Doing the IBX transcoder B workaround causes underruns on
pipe/transcoder A. Just hide them by disabling underrun reporting for
pipe A around the workaround.
It might be possible to avoid the underruns by moving the workaround
to be applied only when enabling pipe A. But I was too lazy to try it
right now, and the current method has been proven to work, so didn't
want to change it too hastily.
Note that this can re-enable underrun reporting on pipe A if was
already disabled due to a previous actual underrun. But that's OK, we
may just get a second underrun report if another real underron occurrs
on pipe A.
v2: Note that pipe A underruns can get re-enabled due to this (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1446225802-11180-1-git-send-email-ville.syrjala@linux.intel.com
This reverts commit 5d250b0591.
It results on a deadlock on platforms where we need to (at least
partially) re-init hpd interrupts from power domain code, since
->hot_plug might again grab a power well reference (to do edid/dp_aux
transactions. At least chv is affected.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: http://mid.gmane.org/20151008133548.GX26517@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
For all the encoders, call the hot_plug if it is registered.
This is required for connected boot and resume cases to generate
fake hpd resulting in reading of edid.
Removing the initial sdvo hot_plug call too so that it will be called
just once from this loop.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Handle the HDMI aspect ratio property the same way in the SDVO code
as we handle it in the HDMI code.
v2: Remove stray whitespace change
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make adjusted_mode const whereever we don't have to modify it. This only
covers cases when we have a local adjusted_mode variable, and doesn't
make any difference for cases where we just dereference
pipe_config->adjusted_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The adjustead_mode crtc_ timings are what we will program into the hardware,
so it's those timings we should be looking practically everywhere.
The normal and crtc_ timings should differ only when stere doubling is
used. In that case the normal timings are the orignal non-doubled
timigns, and crtc_ timings are the doubled timings used by the hardware.
The only case where we continue to look at the normal timings is when we
pass the adjusted_mode to drm_match_{cea,hdmi}_mode() to find the VIC.
drm_edid keeps the modes aronund in the non-double form only, so it
needs the non-double timings to match against.
Done with sed
's/adjusted_mode->\([vhVH]\)/adjusted_mode->crtc_\1/g'
's/adjusted_mode->clock/adjusted_mode->crtc_clock/g'
with a manual s/VDisplay/vdisplay/ within the comment in intel_dvo.c
v2: Update due to intel_dsi.c changes
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the function argument to 'adjusted_mode' whenever the function
only ever gets passed the adjusted_mode.
v2: Update due to intel_dsi.c changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always name any variable pointing at the adjusted mode as
'adjustead_mode'. This will make it much easier to identify
when we should use the crtc_ timings and when we shoudln't.
Conversion was performed with coccinelle:
@@
expression E;
identifier I;
@@
- struct drm_display_mode *I = &E.adjusted_mode;
+ struct drm_display_mode *adjusted_mode = &E.adjusted_mode;
<...
- I
+ adjusted_mode
...>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
[danvet: Fixup conflicts.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_sdvo_select_ddc_bus() and intel_sdvo_select_i2c_bus() have no used
for the passed in 'reg', so just drop it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most of our char* arrays are markes as const already, but a few slipped
through the cracks. Fix it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A couple of hand rolled ARRAY_SIZE()s caught my eye. Get rid of them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First step in removing dpms and validating atomic state.
There can still be a mismatch in the connector state because the dpms
callbacks are still used, but this can not happen immediately after a modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to properly handle failing dpms calls.
When making a wait in i915 interruptible, I've noticed
that the dpms sequence could fail with -ERESTARTSYS because
it was waiting interruptibly for flips. So from now on
allow drivers to fail in their connector dpms callback.
Encoder and crtc dpms callbacks are unaffected.
Changes since v1:
- Update kerneldoc for the drm helper functions.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Resolve conflicts due to different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.2.
I've one other new driver from freescale on my radar, it's been posted
and reviewed, I'd just like to get someone to give it a last look, so
maybe I'll send it or maybe I'll leave it.
There is no major nouveau changes in here, Ben was working on
something big, and we agreed it was a bit late, there wasn't anything
else he considered urgent to merge.
There might be another msm pull for some bits that are waiting on
arm-soc, I'll see how we time it.
This touches some "of" stuff, acks are in place except for the fixes
to the build in various configs,t hat I just applied.
Summary:
New drivers:
- virtio-gpu:
KMS only pieces of driver for virtio-gpu in qemu.
This is just the first part of this driver, enough to run
unaccelerated userspace on. As qemu merges more we'll start
adding the 3D features for the virgl 3d work.
- amdgpu:
a new driver from AMD to driver their newer GPUs. (VI+)
It contains a new cleaner userspace API, and is a clean
break from radeon moving forward, that AMD are going to
concentrate on. It also contains a set of register headers
auto generated from AMD internal database.
core:
- atomic modesetting API completed, enabled by default now.
- Add support for mode_id blob to atomic ioctl to complete interface.
- bunch of Displayport MST fixes
- lots of misc fixes.
panel:
- new simple panels
- fix some long-standing build issues with bridge drivers
radeon:
- VCE1 support
- add a GPU reset counter for userspace
- lots of fixes.
amdkfd:
- H/W debugger support module
- static user-mode queues
- support killing all the waves when a process terminates
- use standard DECLARE_BITMAP
i915:
- Add Broxton support
- S3, rotation support for Skylake
- RPS booting tuning
- CPT modeset sequence fixes
- ns2501 dither support
- enable cmd parser on haswell
- cdclk handling fixes
- gen8 dynamic pte allocation
- lots of atomic conversion work
exynos:
- Add atomic modesetting support
- Add iommu support
- Consolidate drm driver initialization
- and MIC, DECON and MIPI-DSI support for exynos5433
omapdrm:
- atomic modesetting support (fixes lots of things in rewrite)
tegra:
- DP aux transaction fixes
- iommu support fix
msm:
- adreno a306 support
- various dsi bits
- various 64-bit fixes
- NV12MT support
rcar-du:
- atomic and misc fixes
sti:
- fix HDMI timing complaince
tilcdc:
- use drm component API to access tda998x driver
- fix module unloading
qxl:
- stability fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
drm/dp/mst: close deadlock in connector destruction.
drm: Always enable atomic API
drm/vgem: Set unique to "vgem"
of: fix a build error to of_graph_get_endpoint_by_regs function
drm/dp/mst: take lock around looking up the branch device on hpd irq
drm/dp/mst: make sure mst_primary mstb is valid in work function
of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/atomic: Don't set crtc_state->enable manually
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
...
In the commit below, I missed the connector allocation in the function
intel_sdvo_analog_init(), leading to those connectors to have a NULL
state pointer.
commit 08d9bc920d
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri Apr 10 10:59:10 2015 +0300
drm/i915: Allocate connector state together with the connectors
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
While at it also remove the redundant/unneeded w/a like done for hdmi
already.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Mention that this also removes the unneeded w/a, as suggested
by Jesse.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the IBX transcoder B workarounds are not working correctly.
Well, the HDMI one seems to be working somewhat, but the DP one is
definitely busted.
After a bit of experimentation it looks like the best way to make this
work is first disable the port on transcoder B, and then re-enable it
transcoder A, and immediately disable it again.
We can also clean up the code by noting that we can't be called without
a valid crtc. And also note that port A on ILK does not need the
workaround, so let's check for that one too.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On IBX the SDVO/HDMI register write may be masked when enabling the
port, so it may need to written twice. The HDMI code does this, but
the SDVO code does not. Add the workaround to the SDVO code as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use POSTING_READ() in intel_sdvo_write_sdvox() as appropriate.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Connector states were being allocated in intel_setup_outputs() in loop
over all connectors. That meant hot-added connectors would have a NULL
state. Since the change to use a struct drm_atomic_state for the legacy
modeset, connector states are necessary for the i915 driver to function
properly, so that would lead to oopses.
Broken by
commit 944b0c7657
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri Mar 20 16:18:07 2015 +0200
drm/i915: Copy the staged connector config to the legacy atomic state
v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-tested-by: Nicolas Kalkhof <nkalkhof@web.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Connector states were being allocated in intel_setup_outputs() in loop
over all connectors. That meant hot-added connectors would have a NULL
state. Since the change to use a struct drm_atomic_state for the legacy
modeset, connector states are necessary for the i915 driver to function
properly, so that would lead to oopses.
v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-tested-by: Nicolas Kalkhof <nkalkhof@web.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be helpful for adding future platforms. It is better to keep
the information in the single point of truth (the table) instead of
duplicating it into the validity function.
While at it, add dev_priv parameter to the function, also to prepare for
adding future platform support.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename intel_gmbus_is_port_valid to intel_gmbus_is_valid_pin, and rename
port parameters to pin as well. This matches usage all around, as
usually a pin is passed to the validity check function. No functional
changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs refer to pin pairs. Start moving towards using pin rather than
port all around to avoid confusion. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So that we can add connector states to the drm_atomic_state used in the
legacy modeset.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Change 'mutliple' to 'multiple'
Change 'mutlipler' to 'multiplier'
Change 'Haswel' to 'Haswell'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even though we only support atomic plane updates at the moment, we still
need to add an .atomic_get_property() entrypoint for connectors before
we allow the driver to flip on the DRIVER_ATOMIC bit. As soon as that
bit gets set, the DRM core will start adding atomic connector properties
(in addition to the plane properties we care about at the moment), so we
need to be able to handle the new way the DRM core will interact with
us.
For simplicity, we just lookup driver-specific connector properties in
the usual shadow array maintained by the core. Once we get real atomic
modeset support for crtc's and planes, this code should be re-written to
pull the data out of crtc/connector state structures.
v2: Fix intel_dvo and intel_dsi that I missed on the first pass (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to enable/test plane updates via the atomic interface, but as
soon as we flip DRIVER_ATOMIC on, the DRM core will take some atomic
codepaths to lookup properties during drmModeGetConnector() and some of
those codepaths unconditionally dereference connector->state
(specifically when looking up the CRTC ID property in
drm_atomic_connector_get_property()). Create a dummy connector state
for each connector at init time to ensure the DRM core doesn't try to
dereference a NULL connector->state. The actual connector properties
will never be updated or contain useful information, but since we're
doing this specifically for testing/debug of the plane operations (and
only when a specific kernel module option is given), that shouldn't
really matter.
Once we start creating connector states, the DRM core will want to be
able to clean them up for us. We also need to hook up the destruction
entrypoint to the core's helper.
v2: Squash in the patch to set the state destruction hook (Ander & Bob)
v3: Only create dummy connector states when we're actually faking
atomic support. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To match the semantics of drm_crtc->state, which this will eventually
become. The allocation of the memory for config will be fixed in a
followup patch. By adding the extra _config field to intel_crtc it was
possible to generate this entire patch with the cocci script below.
@@ @@
struct intel_crtc {
...
-struct intel_crtc_state config;
+struct intel_crtc_state _config;
+struct intel_crtc_state *config;
...
}
@@ struct intel_crtc *crtc; @@
-memset(&crtc->config, 0, sizeof(crtc->config));
+memset(crtc->config, 0, sizeof(*crtc->config));
@@ @@
__intel_set_mode(...) {
<...
-to_intel_crtc(crtc)->config = *pipe_config;
+(*(to_intel_crtc(crtc)->config)) = *pipe_config;
...>
}
@@ @@
intel_crtc_init(...) {
...
WARN_ON(drm_crtc_index(&intel_crtc->base) != intel_crtc->pipe);
+intel_crtc->config = &intel_crtc->_config;
return;
...
}
@@ struct intel_crtc *crtc; @@
-&crtc->config
+crtc->config
@@ struct intel_crtc *crtc; identifier member; @@
-crtc->config.member
+crtc->config->member
@@ expression E; @@
-&(to_intel_crtc(E)->config)
+to_intel_crtc(E)->config
@@ expression E; identifier member; @@
-to_intel_crtc(E)->config.member
+to_intel_crtc(E)->config->member
v2: Clarify manual changes by splitting them into another patch. (Matt)
Improve cocci script to generate even more of the changes. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The objective is to make this structure usable with the atomic helpers,
so let's start with the rename. Patch generated with coccinelle:
@@ @@
-struct intel_crtc_config {
+struct intel_crtc_state {
...
}
@@ @@
-struct intel_crtc_config
+struct intel_crtc_state
v2: Completely generate the patch with cocci. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
915 doens't support hotplug at all, so we shouldn't try to pretend
otherwise in the SDVO code.
Note: i915 does have hotplug support in hw, we simply never enabled it
in i915.ko: There's only one hpd bit for all outputs, so not worth the
bother to add this special case for this rather old platform.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Clarify that only i915.ko doesn't support hpd on i915g.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When drm properties are created, they are added to mode_config.property_list,
which is then used in drm_mode_config_cleanup() to destroy every single
property created by the driver.
Cc: Chandra Konduru <chandra.konduru@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
misc core patches picked up by Daniel and Jani.
* tag 'topic/core-stuff-2014-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/fb-helper: Remove unnecessary list empty check in drm_fb_helper_debug_enter()
drm/fb-helper: Redundant info->fix.type_aux setting in drm_fb_helper_fill_fix()
drm/debugfs: add an "edid_override" file per connector
drm/debugfs: add a "force" file per connector
drm: add register and unregister functions for connectors
drm: fix uninitialized acquire_ctx fields (v2)
drm: Driver-specific ioctls range from 0x40 to 0x9f
drm: Don't export internal module variables
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On certain platforms pixel_multiplier is read out in
.get_pipe_config(), but it also gets used to calculate the
pixel clock in intel_sdvo_get_config(). If the pipe is disable
but some SDVO outputs are active, we may end up dividing by zero
in intel_sdvo_get_config().
To avoid the problem simply check for zero pixel_multiplier and skip
the division. Another attempt at fixing this involved populating
pixel_multiplier to 1 even for disabled pipes, but that triggered a
WARN because SDVO_CMD_GET_CLOCK_RATE_MULT command failed and thus
encoder_pixel_multiplier was left at zero and didn't match
pipe_config->pixel_multiplier.
The "divide by pixel_multiplier" operation got introduced here:
commit 18442d0878
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 13 16:00:08 2013 +0300
drm/i915: Fix port_clock and adjusted_mode.clock readout all over
and it has caused a regression on certain machines since they would
hit the div-by-zero during resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76520
Cc: <stable@vger.kernel.org> # 3.13+
Tested-by: Tim Richardson <tim@tim-richardson.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This way we can rely on the state cross-checker to have a bit
assurance that we'll get it right.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on those platforms which have a simple bit and don't rely
on the fully programmable CSC unit to do this.
Note that with the current code this includes CHV, but I guess that
platform will match BYT.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We in the pre_enable hook we should only rely on the pipe config and
not on some other state set through properties or detect functions.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SDVO is used by both crtcs using the i9xx_ and the ironlake_
functions. For both cases there is nothing between the
encoder->mode_set and the encoder->pre_enable calls that touches the
hardware.
The vlv_ functions are different since they enable the pll before the
->pre_enable hook. But SDVO isn't supported on vlv platforms, so this
doesn't matter.
We've also already clean up all the sdvo state computation logic, all
relevant parts are already in the ->compute_config hook. So we can
just get rid of the ->mode_set hook by converting it to a ->pre_enable
hook.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When linking the i2c sysfs file into the connector's directory
pass directory and link target in the right order.
This code was introduced with:
commit 931c1c2698
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Feb 11 17:12:51 2014 +0200
drm/i915: sdvo: add i2c sysfs symlink to the connector's directory
This is the same what we do for DP connectors, so make things more
consistent.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_sdvo_get_trained_inputs() returns a bool, check the status
accordingly.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we allow encoders to indicate whether they can be part of a
cloned set with just one flag. That's not flexible enough to describe
the actual hardware capabilities. Instead make it a bitmask of encoder
types with which the current encoder can be cloned.
For now we set the bitmask to allow DVO+DVO and DVO+VGA, which should
match what the old boolean flag allowed. We will add some more cloning
options in the future.
Note that this patch also removes the encoder.possible_clones setting
from encoder setup code - we compute this dynamically.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add Ville's explanation why removing the encoder
possible_clones is save.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the same what we do for DP connectors, so make things more
consistent.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit d9255d5714
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Sep 26 20:05:59 2013 -0300
it became clear that we need to separate the unload sequence into two
parts:
1. remove all interfaces through which new operations on some object
(crtc, encoder, connector) can be started and make sure all pending
operations are completed
2. do the actual tear down of the internal representation of the above
objects
The above commit achieved this separation for connectors by splitting
out the sysfs removal part from the connector's destroy callback and
doing this removal before calling drm_mode_config_cleanup() which does
the actual tear-down of all the drm objects.
Since we'll have to customize the interface removal part for different
types of connectors in the upcoming patches, add a new unregister
callback and move the interface removal part to it.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't modify the packed infoframe data, so we should keep the
const qualifier in place. Just pass the buffer as 'const void *'
instead of 'const uint8_t *' and we can drop the cast entirely.
v2: Do intel_sdvo_write_infoframe() as well
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We had some mode_valid() vfuncs returning an int, others the enum. Let's
use the latter everywhere.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
