Commit 9ebf300078 ("xhci: Fix halted endpoint at stop endpoint command
completion") in 5.12 changes how cancelled URBs are given back.
To cancel a URB xhci driver needs to stop the endpoint first.
To clear a halted endpoint xhci driver needs to reset the endpoint.
In rare cases when an endpoint halt (error) races with a endpoint stop we
need to clear the reset before removing, and giving back the cancelled URB.
The above change in 5.12 takes care of this, but it also relies on the
reset endpoint completion handler to give back the cancelled URBs.
There are cases when driver refuses to queue reset endpoint commands,
for example when a link suddenly goes to an inactive error state.
In this case the cancelled URB is never given back.
Fix this by giving back the URB in the stop endpoint if queuing a reset
endpoint command fails.
Fixes: 9ebf300078 ("xhci: Fix halted endpoint at stop endpoint command completion")
CC: <stable@vger.kernel.org> # 5.12
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same way as Intel Tiger Lake TCSS (Type-C Subsystem) the Alder Lake
TCSS xHCI needs to be runtime suspended whenever possible to allow the
TCSS hardware block to enter D3cold and thus save energy.
Cc: stable@vger.kernel.org
Signed-off-by: Abhijeet Rao <abhijeet.rao@intel.com>
Signed-off-by: Nikunj A. Dadhania <nikunj.dadhania@intel.com>
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WWAN framework provides a unified way to handle WWAN/modems and its
control port(s). It has initially been introduced to support MHI/PCI
modems, offering the same control protocols as the USB variants such as
MBIM, QMI, AT... The WWAN framework exposes these control protocols as
character devices, similarly to cdc-wdm, but in a bus agnostic fashion.
This change adds registration of the USB modem cdc-wdm control endpoints
to the WWAN framework as standard control ports (wwanXpY...).
Exposing cdc-wdm through WWAN framework normally maintains backward
compatibility, e.g:
$ qmicli --device-open-qmi -d /dev/wwan0p1QMI --dms-get-ids
instead of
$ qmicli --device-open-qmi -d /dev/cdc-wdm0 --dms-get-ids
However, some tools may rely on cdc-wdm driver/device name for device
detection. It is then safer to keep the 'legacy' cdc-wdm character
device to prevent any breakage. This is handled in this change by
API mutual exclusion, only one access method can be used at a time,
either cdc-wdm chardev or WWAN API.
Note that unknown channel types (other than MBIM, AT or MBIM) are not
registered to the WWAN framework.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch fixes lack of removing request from ep->pending_list on failure
of the stop endpoint command. Driver even after failing this command
must remove request from ep->pending_list.
Without this fix driver can stuck in cdnsp_gadget_ep_disable function
in loop:
while (!list_empty(&pep->pending_list)) {
preq = next_request(&pep->pending_list);
cdnsp_ep_dequeue(pep, preq);
}
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210420042813.34917-1-pawell@gli-login.cadence.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
When cdns3_gadget_start() fails, a pairing PM usage counter
decrement is needed to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210412054908.7975-1-dinghao.liu@zju.edu.cn
Signed-off-by: Peter Chen <peter.chen@kernel.org>
This code generates a Smatch warning:
drivers/usb/cdns3/cdnsp-mem.c:1085 cdnsp_mem_cleanup()
warn: variable dereferenced before check 'pdev->dcbaa' (see line 1067)
The unchecked dereference happens inside the function when we call:
cdnsp_free_priv_device(pdev);
But fortunately, the "pdev->dcbaa" pointer can never be NULL so it
does not lead to a runtime issue. We can just remove the NULL check
which silences the warning and makes the code consistent.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210505055854.40240-1-pawell@gli-login.cadence.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
fw_devlink expects DT device nodes with "compatible" property to have
struct devices created for them. Since the connector node might not be
populated as a device, mark it as such so that fw_devlink knows not to
wait on this fwnode being populated as a struct device.
Without this patch, USB functionality can be broken on some boards.
Fixes: f7514a6630 ("of: property: fw_devlink: Add support for remote-endpoint")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210506004423.345199-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use first-fit instead of best-fit for LS/FS devices under TT,
we found that best-fit will consume more bandwidth for some
cases.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210507021127.54717-4-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use bitfield instead of bool in struct
Refer to coding-style.rst 17) Using bool:
"If a structure has many true/false values, consider consolidating
them into a bitfield with 1 bit members, or using an appropriate
fixed width type, such as u8."
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210507021127.54717-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not_Supported Message is acceptable in VDM AMS. Redirect the VDM state
machine to VDM_STATE_DONE when receiving Not_Supported and finish the
VDM AMS.
Also, after the loop in vdm_state_machine_work, add more conditions of
VDM states to clear the vdm_sm_running flag because those are all
stopping states when leaving the loop.
In addition, finish the VDM AMS if the port partner responds BUSY.
Fixes: 8dea75e113 ("usb: typec: tcpm: Protocol Error handling")
Fixes: 8d3a0578ad ("usb: typec: tcpm: Respond Wait if VDM state machine is running")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210507062300.1945009-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current design, DISCOVER_IDENTITY is queued to VDM state machine
immediately in Ready states and never retries if it fails in the AMS.
Move the process to a delayed work so that when it fails for some
reasons (e.g. Sink Tx No Go), it can be retried by queueing the work
again. Also fix a problem that the vdm_state is not set to a proper
state if it is blocked by Collision Avoidance mechanism.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210507062300.1945009-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dbc6a4ef0 ("usb: typec: ucsi: save power data objects
in PD mode") introduced retrieval of the PDOs when connected to a
PD-capable source. But only the first 4 PDOs are received since
that is the maximum number that can be fetched at a time given the
MESSAGE_IN length limitation (16 bytes). However, as per the PD spec
a connected source may advertise up to a maximum of 7 PDOs.
If such a source is connected it's possible the PPM could have
negotiated a power contract with one of the PDOs at index greater
than 4, and would be reflected in the request data object's (RDO)
object position field. This would result in an out-of-bounds access
when the rdo_index() is used to index into the src_pdos array in
ucsi_psy_get_voltage_now().
With the help of the UBSAN -fsanitize=array-bounds checker enabled
this exact issue is revealed when connecting to a PD source adapter
that advertise 5 PDOs and the PPM enters a contract having selected
the 5th one.
[ 151.545106][ T70] Unexpected kernel BRK exception at EL1
[ 151.545112][ T70] Internal error: BRK handler: f2005512 [#1] PREEMPT SMP
...
[ 151.545499][ T70] pc : ucsi_psy_get_prop+0x208/0x20c
[ 151.545507][ T70] lr : power_supply_show_property+0xc0/0x328
...
[ 151.545542][ T70] Call trace:
[ 151.545544][ T70] ucsi_psy_get_prop+0x208/0x20c
[ 151.545546][ T70] power_supply_uevent+0x1a4/0x2f0
[ 151.545550][ T70] dev_uevent+0x200/0x384
[ 151.545555][ T70] kobject_uevent_env+0x1d4/0x7e8
[ 151.545557][ T70] power_supply_changed_work+0x174/0x31c
[ 151.545562][ T70] process_one_work+0x244/0x6f0
[ 151.545564][ T70] worker_thread+0x3e0/0xa64
We can resolve this by instead retrieving and storing up to the
maximum of 7 PDOs in the con->src_pdos array. This would involve
two calls to the GET_PDOS command.
Fixes: 992a60ed0d ("usb: typec: ucsi: register with power_supply class")
Fixes: 4dbc6a4ef0 ("usb: typec: ucsi: save power data objects in PD mode")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210503074611.30973-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'retval' is known to be -ENODEV here.
This is a hard-coded default error code which is not useful in the error
message. Moreover, another error message is printed at the end of the
error handling path. The corresponding error code (-ENOMEM) is more
informative.
So remove simplify the first error message.
While at it, also remove the useless initialization of 'retval'.
Fixes: 7d50195f6c ("usb: host: Faraday fotg210-hcd driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/94531bcff98e46d4f9c20183a90b7f47f699126c.1620333419.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When extcon is used in combination with dwc3, it is assumed that the dwc3
registers are untouched and as such are only configured if VBUS is valid
or ID is tied to ground.
In case VBUS is not valid or ID is floating, the registers are not
configured as such during driver initialization, causing a wrong
default state during boot.
If the registers are not in a default state, because they are for
instance touched by a boot loader, this can cause for a kernel error.
Signed-off-by: Marcel Hamer <marcel@solidxs.se>
Link: https://lore.kernel.org/r/20210427122118.1948340-1-marcel@solidxs.se
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_for_each_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210504222337.3151726-1-andy.shevchenko@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After receiving Sink Capabilities Message in GET_SINK_CAP AMS, it is
incorrect to call tcpm_pd_handle_state because the Message is expected
and the current state is not Ready states. The result of this incorrect
operation ends in Soft Reset which is definitely wrong. Simply
forwarding to Ready States is enough to finish the AMS.
Fixes: 8dea75e113 ("usb: typec: tcpm: Protocol Error handling")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503171849.2605302-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally, the core and platform drivers were separate modules, so each
had its own module info. Since commit 2d1165a4b9 (usb: dwc2: remove
dwc2_platform.ko) platform.c is included in the core module, which now
contains duplicate module info (from core.c and platform.c).
Due to the linking order and modinfo implementation, running `modinfo`
on the resulting dwc2.ko shows just the info from platform.c, rather
than that from core.c, suggesting that I am the author of the entire
dwc2 module. Since platform.c is just a minor part of the entire module,
this removes its module info in favor of the info from core.c.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Link: https://lore.kernel.org/r/20210503180538.64423-1-matthijs@stdin.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: 6dd2565989 ("usb: dwc3: add imx8mp dwc3 glue layer driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210508015310.1627-1-thunder.leizhen@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New schema of usb controller DT-node should be named with prefix
"^usb(@.*)?", dt changed the node name, but missed counter part
change in driver, fix it by switching to use compatible string as
the dwc3 core compatible string keeps "snps,dwc3" in all dt.
Fixes: d1689cd3c0 ("arm64: dts: imx8mp: Use the correct name for child node "snps, dwc3"")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1619765836-20387-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an error is received when issuing a start or update transfer
command, the error handler will stop all active requests (including
the current USB request), and call dwc3_gadget_giveback() to notify
function drivers of the requests which have been stopped. Avoid
returning an error for kick transfer during EP queue, to remove
duplicate cleanup operations on the request being queued.
Fixes: 8d99087c2d ("usb: dwc3: gadget: Properly handle failed kick_transfer")
cc: stable@vger.kernel.org
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1620410119-24971-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of commit e81a7018d9 ("usb: dwc3: allocate gadget structure
dynamically") the dwc3_gadget_release() was added which will free
the dwc->gadget structure upon the device's removal when
usb_del_gadget_udc() is called in dwc3_gadget_exit().
However, simply freeing the gadget results a dangling pointer
situation: the endpoints created in dwc3_gadget_init_endpoints()
have their dep->endpoint.ep_list members chained off the list_head
anchored at dwc->gadget->ep_list. Thus when dwc->gadget is freed,
the first dwc3_ep in the list now has a dangling prev pointer and
likewise for the next pointer of the dwc3_ep at the tail of the list.
The dwc3_gadget_free_endpoints() that follows will result in a
use-after-free when it calls list_del().
This was caught by enabling KASAN and performing a driver unbind.
The recent commit 568262bf54 ("usb: dwc3: core: Add shutdown
callback for dwc3") also exposes this as a panic during shutdown.
There are a few possibilities to fix this. One could be to perform
a list_del() of the gadget->ep_list itself which removes it from
the rest of the dwc3_ep chain.
Another approach is what this patch does, by splitting up the
usb_del_gadget_udc() call into its separate "del" and "put"
components. This allows dwc3_gadget_free_endpoints() to be
called before the gadget is finally freed with usb_put_gadget().
Fixes: e81a7018d9 ("usb: dwc3: allocate gadget structure dynamically")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210501093558.7375-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
Fixes: fe0b94abcd ("usb: dwc2: gadget: manage ep0 state in software")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/20210506112200.2893922-1-phil@raspberrypi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device event corresponding to End of Periodic Frame is only
found on older IP revisions (2.10a and prior, according to a
cursory SNPS databook search). On revisions 2.30a and newer,
including DWC3.1, the same event value and corresponding DEVTEN
bit were repurposed to indicate that the link has gone into
suspend state (U3 or L2/L1).
EOPF events had never been enabled before in this driver, and
going forward we expect current and future DWC3-based devices
won't likely to be using such old DWC3 IP revisions either.
Hence rather than keeping the deprecated EOPF macro names let's
rename them to indicate their usage for suspend events.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210428090111.3370-2-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72704f876f ("dwc3: gadget: Implement the suspend entry event
handler") introduced (nearly 5 years ago!) an interrupt handler for
U3/L1-L2 suspend events. The problem is that these events aren't
currently enabled in the DEVTEN register so the handler is never
even invoked. Fix this simply by enabling the corresponding bit
in dwc3_gadget_enable_irq() using the same revision check as found
in the handler.
Fixes: 72704f876f ("dwc3: gadget: Implement the suspend entry event handler")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210428090111.3370-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Intel Merrifield LPM is causing host to reset port after a timeout.
By disabling LPM entirely this is prevented.
Fixes: 066c095934 ("usb: dwc3: pci: Enable extcon driver for Intel Merrifield")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210425150947.5862-1-ftoth@exalondelft.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a cycle of callbacks scheduling works which submit
URBs with those callbacks. This needs to be blocked, stopped
and unblocked to untangle the circle.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20210426092622.20433-1-oneukum@suse.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quieten implicit-fallthrough warnings in fsl_qe_udc.c:
../drivers/usb/gadget/udc/fsl_qe_udc.c: In function 'qe_ep_init':
../drivers/usb/gadget/udc/fsl_qe_udc.c:542:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
542 | if ((max == 128) || (max == 256) || (max == 512))
../drivers/usb/gadget/udc/fsl_qe_udc.c:563:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
563 | if (max <= 1024)
../drivers/usb/gadget/udc/fsl_qe_udc.c:566:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
566 | if (max <= 64)
../drivers/usb/gadget/udc/fsl_qe_udc.c:580:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
580 | if (max <= 1024)
../drivers/usb/gadget/udc/fsl_qe_udc.c:596:5: warning: this statement may fall through [-Wimplicit-fallthrough=]
596 | switch (max) {
This basically just documents what is currently being done.
If any of them need to do something else, just say so or
even make the change.
Cc: Li Yang <leoyang.li@nxp.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210428040855.25907-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The parameters passed to allow_link and drop_link functions are never NULL.
That means the result of container_of() on those parameters is also
never NULL, even though the reference into the structure points to the
first element of the structure. Remove the unnecessary NULL checks.
This change was made automatically with the following Coccinelle script.
A now obsolete 'out:' label was removed manually.
@@
type t;
identifier v;
statement s;
@@
<+...
(
t v = container_of(...);
|
v = container_of(...);
)
...
when != v
- if (\( !v \| v == NULL \) ) s
...+>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210424145443.170413-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the device id for the ADLINK ND-6530 which is a PL2303GC based
device.
Signed-off-by: Zolton Jheng <s6668c2t@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds support for the Startech.com generic serial to USB converter.
It seems to be a bone stock TI_3410. I have been using this patch for
years.
Signed-off-by: Sean MacLennan <seanm@seanm.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Add the IDS GmbH Vendor ID and the Product IDs for SI31A (2xRS232)
and CM31A (LoRaWAN Modem).
Signed-off-by: Dominik Andreas Schorpp <dominik.a.schorpp@ids.de>
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
This series consists of the usual driver updates (ufs, target, tcmu,
smartpqi, lpfc, zfcp, qla2xxx, mpt3sas, pm80xx). The major core
change is using a sbitmap instead of an atomic for queue tracking.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYInvqCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYh2AP0SgqqL
WYZRT2oiyBOKD28v+ceOSiXvgjPlqABwVMC0BAEAn29/wNCxyvzZ1k/b0iPJ4M+S
klkSxLzXKQLzJBgdK5w=
=p5B/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, target, tcmu,
smartpqi, lpfc, zfcp, qla2xxx, mpt3sas, pm80xx).
The major core change is using a sbitmap instead of an atomic for
queue tracking"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (412 commits)
scsi: target: tcm_fc: Fix a kernel-doc header
scsi: target: Shorten ALUA error messages
scsi: target: Fix two format specifiers
scsi: target: Compare explicitly with SAM_STAT_GOOD
scsi: sd: Introduce a new local variable in sd_check_events()
scsi: dc395x: Open-code status_byte(u8) calls
scsi: 53c700: Open-code status_byte(u8) calls
scsi: smartpqi: Remove unused functions
scsi: qla4xxx: Remove an unused function
scsi: myrs: Remove unused functions
scsi: myrb: Remove unused functions
scsi: mpt3sas: Fix two kernel-doc headers
scsi: fcoe: Suppress a compiler warning
scsi: libfc: Fix a format specifier
scsi: aacraid: Remove an unused function
scsi: core: Introduce enum scsi_disposition
scsi: core: Modify the scsi_send_eh_cmnd() return value for the SDEV_BLOCK case
scsi: core: Rename scsi_softirq_done() into scsi_complete()
scsi: core: Remove an incorrect comment
scsi: core: Make the scsi_alloc_sgtables() documentation more accurate
...
- Clean up SCHED_DEBUG: move the decades old mess of sysctl, procfs and debugfs interfaces
to a unified debugfs interface.
- Signals: Allow caching one sigqueue object per task, to improve performance & latencies.
- Improve newidle_balance() irq-off latencies on systems with a large number of CPU cgroups.
- Improve energy-aware scheduling
- Improve the PELT metrics for certain workloads
- Reintroduce select_idle_smt() to improve load-balancing locality - but without the previous
regressions
- Add 'scheduler latency debugging': warn after long periods of pending need_resched. This
is an opt-in feature that requires the enabling of the LATENCY_WARN scheduler feature,
or the use of the resched_latency_warn_ms=xx boot parameter.
- CPU hotplug fixes for HP-rollback, and for the 'fail' interface. Fix remaining
balance_push() vs. hotplug holes/races
- PSI fixes, plus allow /proc/pressure/ files to be written by CAP_SYS_RESOURCE tasks as well
- Fix/improve various load-balancing corner cases vs. capacity margins
- Fix sched topology on systems with NUMA diameter of 3 or above
- Fix PF_KTHREAD vs to_kthread() race
- Minor rseq optimizations
- Misc cleanups, optimizations, fixes and smaller updates
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=E7mz
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2021-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Clean up SCHED_DEBUG: move the decades old mess of sysctl, procfs and
debugfs interfaces to a unified debugfs interface.
- Signals: Allow caching one sigqueue object per task, to improve
performance & latencies.
- Improve newidle_balance() irq-off latencies on systems with a large
number of CPU cgroups.
- Improve energy-aware scheduling
- Improve the PELT metrics for certain workloads
- Reintroduce select_idle_smt() to improve load-balancing locality -
but without the previous regressions
- Add 'scheduler latency debugging': warn after long periods of pending
need_resched. This is an opt-in feature that requires the enabling of
the LATENCY_WARN scheduler feature, or the use of the
resched_latency_warn_ms=xx boot parameter.
- CPU hotplug fixes for HP-rollback, and for the 'fail' interface. Fix
remaining balance_push() vs. hotplug holes/races
- PSI fixes, plus allow /proc/pressure/ files to be written by
CAP_SYS_RESOURCE tasks as well
- Fix/improve various load-balancing corner cases vs. capacity margins
- Fix sched topology on systems with NUMA diameter of 3 or above
- Fix PF_KTHREAD vs to_kthread() race
- Minor rseq optimizations
- Misc cleanups, optimizations, fixes and smaller updates
* tag 'sched-core-2021-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (61 commits)
cpumask/hotplug: Fix cpu_dying() state tracking
kthread: Fix PF_KTHREAD vs to_kthread() race
sched/debug: Fix cgroup_path[] serialization
sched,psi: Handle potential task count underflow bugs more gracefully
sched: Warn on long periods of pending need_resched
sched/fair: Move update_nohz_stats() to the CONFIG_NO_HZ_COMMON block to simplify the code & fix an unused function warning
sched/debug: Rename the sched_debug parameter to sched_verbose
sched,fair: Alternative sched_slice()
sched: Move /proc/sched_debug to debugfs
sched,debug: Convert sysctl sched_domains to debugfs
debugfs: Implement debugfs_create_str()
sched,preempt: Move preempt_dynamic to debug.c
sched: Move SCHED_DEBUG sysctl to debugfs
sched: Don't make LATENCYTOP select SCHED_DEBUG
sched: Remove sched_schedstats sysctl out from under SCHED_DEBUG
sched/numa: Allow runtime enabling/disabling of NUMA balance without SCHED_DEBUG
sched: Use cpu_dying() to fix balance_push vs hotplug-rollback
cpumask: Introduce DYING mask
cpumask: Make cpu_{online,possible,present,active}() inline
rseq: Optimise rseq_get_rseq_cs() and clear_rseq_cs()
...
Here is the big set of USB and Thunderbolt driver updates for 5.13-rc1.
Lots of little things in here, with loads of tiny fixes and cleanups
over these drivers, as well as these "larger" changes:
- thunderbolt updates and new features added
- xhci driver updates and split out of a mediatek-specific xhci
driver from the main xhci module to make it easier to work
with (something that I have been wanting for a while).
- loads of typec feature additions and updates
- dwc2 driver updates
- dwc3 driver updates
- gadget driver fixes and minor updates
- loads of usb-serial cleanups and fixes and updates
- usbip documentation updates and fixes
- lots of other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIa42A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymMEACgkQBzLb5W/IocS+oq7+D7P3V581sAn1Dcy2Qq
Yz370/X2hrjXAyIm7/Cz
=5dj/
-----END PGP SIGNATURE-----
Merge tag 'usb-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
5.13-rc1.
Lots of little things in here, with loads of tiny fixes and cleanups
over these drivers, as well as these "larger" changes:
- thunderbolt updates and new features added
- xhci driver updates and split out of a mediatek-specific xhci
driver from the main xhci module to make it easier to work with
(something that I have been wanting for a while).
- loads of typec feature additions and updates
- dwc2 driver updates
- dwc3 driver updates
- gadget driver fixes and minor updates
- loads of usb-serial cleanups and fixes and updates
- usbip documentation updates and fixes
- lots of other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (371 commits)
usb: Fix up movement of USB core kerneldoc location
usb: dwc3: gadget: Handle DEV_TXF_FLUSH_BYPASS capability
usb: dwc3: Capture new capability register GHWPARAMS9
usb: gadget: prevent a ternary sign expansion bug
usb: dwc3: core: Do core softreset when switch mode
usb: dwc2: Get rid of useless error checks in suspend interrupt
usb: dwc2: Update dwc2_handle_usb_suspend_intr function.
usb: dwc2: Add exit hibernation mode before removing drive
usb: dwc2: Add hibernation exiting flow by system resume
usb: dwc2: Add hibernation entering flow by system suspend
usb: dwc2: Allow exit hibernation in urb enqueue
usb: dwc2: Move exit hibernation to dwc2_port_resume() function
usb: dwc2: Move enter hibernation to dwc2_port_suspend() function
usb: dwc2: Clear GINTSTS_RESTOREDONE bit after restore is generated.
usb: dwc2: Clear fifo_map when resetting core.
usb: dwc2: Allow exiting hibernation from gpwrdn rst detect
usb: dwc2: Fix hibernation between host and device modes.
usb: dwc2: Fix host mode hibernation exit with remote wakeup flow.
usb: dwc2: Reset DEVADDR after exiting gadget hibernation.
usb: dwc2: Update exit hibernation when port reset is asserted
...
Here is the big set of tty and serial driver updates for 5.13-rc1.
Actually busy this release, with a number of cleanups happening:
- much needed core tty cleanups by Jiri Slaby
- removal of unused and orphaned old-style serial drivers. If
anyone shows up with this hardware, it is trivial to restore
these but we really do not think they are in use anymore.
- fixes and cleanups from Johan Hovold on a number of termios
setting corner cases that loads of drivers got wrong as well
as removing unneeded code due to tty core changes from long
ago that were never propagated out to the drivers
- loads of platform-specific serial port driver updates and
fixes
- coding style cleanups and other small fixes and updates all
over the tty/serial tree.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIa3NQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykMXgCfX3FZgKveI4l94ChXSy4OyKwycHUAn00BzrMC
/7BwA1FnjQnC4zSzuHnm
=bAas
-----END PGP SIGNATURE-----
Merge tag 'tty-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.13-rc1.
Actually busy this release, with a number of cleanups happening:
- much needed core tty cleanups by Jiri Slaby
- removal of unused and orphaned old-style serial drivers. If anyone
shows up with this hardware, it is trivial to restore these but we
really do not think they are in use anymore.
- fixes and cleanups from Johan Hovold on a number of termios setting
corner cases that loads of drivers got wrong as well as removing
unneeded code due to tty core changes from long ago that were never
propagated out to the drivers
- loads of platform-specific serial port driver updates and fixes
- coding style cleanups and other small fixes and updates all over
the tty/serial tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
serial: extend compile-test coverage
serial: stm32: add FIFO threshold configuration
dt-bindings: serial: 8250: update TX FIFO trigger level
dt-bindings: serial: stm32: override FIFO threshold properties
dt-bindings: serial: add RX and TX FIFO properties
serial: xilinx_uartps: drop low-latency workaround
serial: vt8500: drop low-latency workaround
serial: timbuart: drop low-latency workaround
serial: sunsu: drop low-latency workaround
serial: sifive: drop low-latency workaround
serial: txx9: drop low-latency workaround
serial: sa1100: drop low-latency workaround
serial: rp2: drop low-latency workaround
serial: rda: drop low-latency workaround
serial: owl: drop low-latency workaround
serial: msm_serial: drop low-latency workaround
serial: mpc52xx_uart: drop low-latency workaround
serial: meson: drop low-latency workaround
serial: mcf: drop low-latency workaround
serial: lpc32xx_hs: drop low-latency workaround
...
DWC_usb32 IP introduces a new behavior when handling NoStream event for
IN endpoints. If the controller is capable of DEV_TXF_FLUSH_BYPASS, then
the driver does not need to force to restart stream for IN endpoints.
The controller will generate ERDY and restart the stream periodically.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/65c3070c666cd6b8beeee62d7f8e3e704ebf2d32.1619134559.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is that "req->actual" is a u32, "req->status" is an int, and
iocb->ki_complete() takes a long. We would expect that a negative error
code in "req->status" would translate to a negative long value.
But what actually happens is that because "req->actual" is a u32, the
error codes is type promoted to a high positive value and then remains
a positive value when it is cast to long. (No sign expansion).
We can fix this by casting "req->status" to long.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YIE7RrBPLWc3XtMg@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: John Stultz <john.stultz@linaro.org>
According to the programming guide, to switch mode for DRD controller,
the driver needs to do the following.
To switch from device to host:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(host mode)
3. Reset the host with USBCMD.HCRESET
4. Then follow up with the initializing host registers sequence
To switch from host to device:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(device mode)
3. Reset the device with DCTL.CSftRst
4. Then follow up with the initializing registers sequence
Currently we're missing step 1) to do GCTL.CoreSoftReset and step 3) of
switching from host to device. John Stult reported a lockup issue seen
with HiKey960 platform without these steps[1]. Similar issue is observed
with Ferry's testing platform[2].
So, apply the required steps along with some fixes to Yu Chen's and John
Stultz's version. The main fixes to their versions are the missing wait
for clocks synchronization before clearing GCTL.CoreSoftReset and only
apply DCTL.CSftRst when switching from host to device.
[1] https://lore.kernel.org/linux-usb/20210108015115.27920-1-john.stultz@linaro.org/
[2] https://lore.kernel.org/linux-usb/0ba7a6ba-e6a7-9cd4-0695-64fc927e01f1@gmail.com/
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Ferry Toth <fntoth@gmail.com>
Cc: Wesley Cheng <wcheng@codeaurora.org>
Cc: <stable@vger.kernel.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Wesley Cheng <wcheng@codeaurora.org>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/374440f8dcd4f06c02c2caf4b1efde86774e02d9.1618521663.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Squashed from Douglas Anderson's suggested commit
"usb: dwc2: Get rid of useless error checks for
hibernation/partial power down"
- After this commit there should never be any
case where dwc2_enter_partial_power_down() and
dwc2_enter_hibernation() are called when
'params.power_down' is not correct. Get rid of
the pile of error checking.
- As part of this cleanup some of the error messages
not to have __func__ in them. That's not needed
for dev_err() calls since they already have the
device name as part of the message.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210416124843.9EDCDA005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid working in two modes (partial power down
and hibernation) changed conditions for entering
partial power down or hibernation.
Instead of checking hw_params.power_optimized and
hw_params.hibernation now checking power_down
param which already set to one of the options
(Hibernation or Partial Power Down) based on
OTG_EN_PWROPT.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124835.9F257A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc2 core is in hibernation mode loading
driver again causes driver fail. Because in
that mode registers are not accessible.
In order to exit from hibernation checking
dwc2 core power saving state in "dwc2_driver_remove()"
function. If core is in hibernation, then checking the
operational mode of the driver. To check whether dwc2 core
is operating in host mode or device mode there is one way
which is retrieving the backup value of "gotgctl" and compare
the "CurMod" value. If previously core entered hibernation
in host mode then the exit is performed for host if not then
exit is performed for device mode. The introduced checking
is because in hibernation state all registers are not
accessible.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124827.9BB59A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a new flow of exiting hibernation when PC is resumed
from suspend state.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124819.A3B26A005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a new flow of entering hibernation when PC is
hibernated or suspended.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124811.BBFDBA005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When core is in hibernation state and an external
hub is connected, upper layer sends URB enqueue request,
which results in port reset issue.
- Added exit from hibernation state to avoid port
reset issue and process upper layer request properly.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124803.D1C1FA005F@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This move is done to call hibernation exit handler in
"dwc2_port_resume()" function when core receives port resume.
Otherwise it could be confusing to exit hibernation in
"dwc2_hcd_hub_control()" function but other power saving modes
in "dwc2_port_resume()" function.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124755.E47F3A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This move is done to call enter hibernation handler in
"dwc2_port_suspend()" function when core receives port suspend.
Otherwise it could be confusing to enter to hibernation in
"dwc2_hcd_hub_control()" function but other power saving modes
in "dwc2_port_suspend()" function.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124747.EE79EA005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When hibernation exit is performed the dwc2_hib_restore_common()
function is called. In that function we wait until GINTSTS_RESTOREDONE
bit is set. However, after the setting of that bit we get a lot of
(dwc2_hsotg_irq:) interrupts which indicates that (GINTSTS.RstrDoneInt)
restore done interrupt is asserted.
To avoid restore done interrupt storm after restore is generated
clear GINTSTS_RESTOREDONE bit in GINTSTS register.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124739.D6269A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switching from device mode to host mode by disconnecting
device cable core enters and exits form hibernation.
However, the fifo map remains not cleared. It results
to a WARNING (WARNING: CPU: 5 PID: 0 at drivers/usb/dwc2/
gadget.c:307 dwc2_hsotg_init_fifo+0x12/0x152 [dwc2])
if in host mode we disconnect the micro a to b host
cable. Because core reset occurs.
To avoid the WARNING, fifo_map should be cleared
in dwc2_core_reset() function by taking into account configs.
fifo_map must be cleared only if driver is configured in
"CONFIG_USB_DWC2_PERIPHERAL" or "CONFIG_USB_DWC2_DUAL_ROLE"
mode.
- Added "static inline void dwc2_clear_fifo_map()" helper
function to clear fifo_map with peripheral or dual role mode.
- Added a dummy version of "dwc2_clear_fifo_map()" helper
for host-only mode.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124731.C500AA005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device cable is disconnected core receives suspend
interrupt and enters hibernation. After entering
into hibernation GPWRDN_RST_DET and GPWRDN_STS_CHGINT
interrupts are asserted.
Allowed exit from gadget hibernation from
GPWRDN_RST_DET by checking only linestate.
Changed the return type of "dwc2_handle_gpwrdn_intr()"
function from void to int because exit from hibernation
functions have a return value.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124723.B6F17A005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When core is in hibernation in host mode and a device cable
was connected then driver exited from device hibernation.
However, registers saved for host mode and when exited from
device hibernation register restore would be done for device
register which was wrong because there was no device registers
stored to restore.
- Added dwc_handle_gpwrdn_disc_det() function which handles
gpwrdn disconnect detect flow and exits hibernation
without restoring the registers.
- Updated exiting from hibernation in GPWRDN_STS_CHGINT with
calling dwc_handle_gpwrdn_disc_det() function. Here no register
is restored which is the solution described above.
Fixes: 65c9c4c6b0 ("usb: dwc2: Add dwc2_handle_gpwrdn_intr() handler")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124715.75355A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added setting "port_connect_status_change" flag to "1" in order
to re-enumerate, because after exit from hibernation port
connection status is not detected.
Fixes: c5c403dc43 ("usb: dwc2: Add host/device hibernation functions")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124707.5EEC2A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially resetting device address was done in dwc2_hsotg_irq()
interrupt handler. However, when core is hibernated USB RESET
is not handled in dwc2_hsotg_irq() handler, instead USB RESET
interrupt is handled in dwc2_handle_gpwrdn_intr() handler.
- Added reset device address to zero when core exits from gadget
hibernation.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124659.652CFA005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to check for "DWC2_POWER_DOWN_PARAM_HIBERNATION" param
as "hsotg->hibernated" flag is already enough for exiting from
hibernation mode.
- Removes checking of "DWC2_POWER_DOWN_PARAM_HIBERNATION" param.
- For code readability Hibernation exit code moved after
debug message print.
- Added "dwc2_exit_hibernation()" function error checking.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124651.51C8DA005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 5.13-rc1, including:
- better type detection for pl2303
- support for more line speeds for pl2303 (TA/TB)
- fixed CSIZE handling for the new xr driver
- core support for multi-interface functions
- TIOCGSERIAL and TIOCSSERIAL fixes
- generic TIOCSSERIAL support (e.g. for closing_wait)
- fixed return value for unsupported ioctls
- support for gpio valid masks in cp210x
- drain-delay fixes and improvements
- support for multi-port devices for xr
- generalisation of the xr driver to support three new device classes
(XR21B142X, XR21B1411 and XR2280X)
Included are also various clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYIE2iwAKCRALxc3C7H1l
CFJsAQCd6rX6VyteR6RUmmTjmGDyRwxsXGniw9bf36dzhlKncwEAga2E+47FGHYm
YiNQzfcETfjGO21usS1BWhNvzf/gsgs=
=1FU1
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.13-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.13-rc1
Here are the USB-serial updates for 5.13-rc1, including:
- better type detection for pl2303
- support for more line speeds for pl2303 (TA/TB)
- fixed CSIZE handling for the new xr driver
- core support for multi-interface functions
- TIOCGSERIAL and TIOCSSERIAL fixes
- generic TIOCSSERIAL support (e.g. for closing_wait)
- fixed return value for unsupported ioctls
- support for gpio valid masks in cp210x
- drain-delay fixes and improvements
- support for multi-port devices for xr
- generalisation of the xr driver to support three new device classes
(XR21B142X, XR21B1411 and XR2280X)
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.13-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (72 commits)
USB: cdc-acm: add more Maxlinear/Exar models to ignore list
USB: serial: xr: add copyright notice
USB: serial: xr: reset FIFOs on open
USB: serial: xr: add support for XR22801, XR22802, XR22804
USB: serial: xr: add support for XR21B1411
USB: serial: xr: add support for XR21B1421, XR21B1422 and XR21B1424
USB: serial: xr: add type abstraction
USB: serial: xr: drop type prefix from shared defines
USB: serial: xr: move pin configuration to probe
USB: serial: xr: rename GPIO-pin defines
USB: serial: xr: rename GPIO-mode defines
USB: serial: xr: add support for XR21V1412 and XR21V1414
USB: serial: ti_usb_3410_5052: clean up termios CSIZE handling
USB: serial: ti_usb_3410_5052: use kernel types consistently
USB: serial: ti_usb_3410_5052: add port-command helpers
USB: serial: ti_usb_3410_5052: clean up vendor-request helpers
USB: serial: ti_usb_3410_5052: drop unnecessary packed attributes
USB: serial: io_ti: drop unnecessary packed attributes
USB: serial: io_ti: use kernel types consistently
USB: serial: io_ti: add read-port-command helper
...
The programming guide incorrectly stated that the DCFG.bInterval_m1 must
be set to 0 when operating in fullspeed. There's no such limitation for
all IPs. See DWC_usb3x programming guide section 3.2.2.1.
Fixes: a1679af85b ("usb: dwc3: gadget: Fix setting of DEPCFG.bInterval_m1")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5d4139ae89d810eb0a2d8577fb096fc88e87bfab.1618472454.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PM will take care of the status of child device, so no need
check each port anymore.
Suggested-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618555706-6810-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2 driver has everything we need to run
in ACPI mode except for the ACPI module device table
boilerplate. With that added and identified as "BCM2848",
an id in use by other OSs for this device, the dw2
controller on the BCM2711 will work.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20210413215834.3126447-2-jeremy.linton@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
suspend() does its poisoning conditionally, resume() does it
unconditionally. On a device with combined interfaces this
will balance, on a device with two interfaces the counter will
go negative and resubmission will fail.
Both actions need to be done conditionally.
Fixes: 6069e3e927 ("USB: cdc-acm: untangle a circular dependency between callback and softint")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210421074513.4327-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)
Information of this hub:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=5487 Rev= 1.47
S: Manufacturer=Dell Inc.
S: Product=Dell dock
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.
The quirky hub needs the reset-resume quirk to function correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable status is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed and move the
declaration of status to the scope where it is used.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210420110622.377339-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable result is being assigned with a value that is
never read, the assignment is redundant and can be removed.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210420113818.378478-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.
The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:
usb_gadget_disconnect(udc->gadget);
if (udc->gadget->irq)
synchronize_irq(udc->gadget->irq);
udc->driver->unbind(udc->gadget);
usb_gadget_udc_stop(udc);
usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.
But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.
To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.
Reported-by: syzbot+eb4674092e6cc8d9e0bd@syzkaller.appspotmail.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210419033713.3021-1-mail@anirudhrb.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The START_TRANSFER command needs to be executed while in ON/U0 link
state (with an exception during register initialization). Don't use
dwc->link_state to check this since the driver only tracks the link
state when the link state change interrupt is enabled. Check the link
state from DSTS register instead.
Note that often the host already brings the device out of low power
before it sends/requests the next transfer. So, the user won't see any
issue when the device starts transfer then. This issue is more
noticeable in cases when the device delays starting transfer, which can
happen during delayed control status after the host put the device in
low power.
Fixes: 799e9dc829 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/bcefaa9ecbc3e1936858c0baa14de6612960e909.1618884221.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon driver unbind usb_free_all_descriptors() function frees all
speed descriptor pointers without setting them to NULL. In case
gadget speed changes (i.e from super speed plus to super speed)
after driver unbind only upto super speed descriptor pointers get
populated. Super speed plus desc still holds the stale (already
freed) pointer. Fix this issue by setting all descriptor pointers
to NULL after freeing them in usb_free_all_descriptors().
Fixes: f5c61225cf ("usb: gadget: Update function for SuperSpeedPlus")
cc: stable@vger.kernel.org
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1619034452-17334-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply"
introduced a regression for req_out_volt and req_op_curr calculation.
req_out_volt should consider the newly calculated max voltage instead
of previously accepted max voltage by the port partner. Likewise,
req_op_curr should consider the newly calculated max current instead
of previously accepted max current by the port partner.
Fixes: e3a0720224 ("usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210415050121.1928298-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A dedicated wakeup irq will be used to handle runtime suspend/resume,
we use dev_pm_set_dedicated_wake_irq API to take care of requesting
and attaching wakeup irq, then the suspend/resume framework will help
to enable/disable wakeup irq.
The runtime PM is default off since some platforms may not support it.
users can enable it via power/control (set "auto") in sysfs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618031406-15347-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a PD charger advertising Rp-3.0 is connected to a sink port, the
sink port current limit would 3A, during SNK_DISCOVERY, till power
negotiation starts. Once the negotiation starts the power limit needs
to drop down to pSnkStby(500mA @ 5V) and to negotiated current limit
once the explicit contract is in place. Not all charging loops can ramp
up to 3A and drop down to 500mA within tSnkStdby which is 15ms. The port
partner might hard reset if tSnkStdby is not met.
To solve this problem, this patch introduces slow-charger-loop which
when set makes the port request PD_P_SNK_STDBY_MW upon entering
SNK_DISCOVERY(instead of 3A or the 1.5A during SNK_DISCOVERY) and the
actual currrent limit after RX of PD_CTRL_PSRDY for PD link or during
SNK_READY for non-pd link.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a shutdown callback to USB DWC core driver to ensure that
it is properly shutdown in reboot/shutdown path. This is required
where SMMU address translation is enabled like on SC7180
SoC and few others. If the hardware is still accessing memory after
SMMU translation is disabled as part of SMMU shutdown callback in
system reboot or shutdown path, then IOVAs(I/O virtual address)
which it was using will go on the bus as the physical addresses which
might result in unknown crashes (NoC/interconnect errors).
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Link: https://lore.kernel.org/r/1618380209-20114-1-git-send-email-sanm@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the controller handles single stream only. So, Ignore Packet
Pending bit for stream selection and don't search for another stream if
the host sends Data Packet with PP=0 (for OUT direction) or ACK with
NumP=0 and PP=0 (for IN direction). This slightly improves the stream
performance.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/097ba9e104c143f7ba0195ebff29390ec3043692.1618282705.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is another branded 8153 device that doesn't work well with LPM
enabled:
[ 400.597506] r8152 5-1.1:1.0 enx482ae3a2a6f0: Tx status -71
So disable LPM to resolve the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1922651
Link: https://lore.kernel.org/r/20210412135455.791971-1-kai.heng.feng@canonical.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch complains about a potential missing error code:
drivers/usb/typec/port-mapper.c:168 typec_link_port()
warn: missing error code 'ret'
This is a false positive and returning zero is intentional. Let's
re-arrange the code to silence the warning and make the intent more
clear.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YHadaACH8Mq/10F7@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the xr_serial got support for other models, add their USB IDs
as well.
The Maxlinear/Exar USB UARTs can be used in either ACM mode using the
cdc-acm driver or in "custom driver" mode in which further features such
as hardware and software flow control, GPIO control and in-band
line-status reporting are available.
In ACM mode the device always enables RTS/CTS flow control, something
which could prevent transmission in case the CTS input isn't wired up
correctly.
Ensure that cdc_acm will not bind to these devices if the custom
USB-serial driver is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/5155887a764cbc11f8da0217fe08a24a77d120b4.1616571453.git.mchehab+huawei@kernel.org
[ johan: rewrite commit message, clean up entries ]
Cc: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reset the transmit and receive FIFOs before enabling the UARTs as part
of open() in order to flush any stale data.
Note that the XR21V141X needs a type-specific implementation due to its
UART Manager registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
The XR22801, XR22802 and XR22804 are compound devices with an embedded
hub and up to seven downstream USB devices including one, two or four
UARTs respectively.
The UART function is similar to XR21B142X but most registers are offset
by 0x40, the register requests are different and are directed at the
device rather than interface, and 5 and 6-bit words are not supported.
Signed-off-by: Johan Hovold <johan@kernel.org>
The single-port XR21B1411 is similar to the XR21B142X type but uses
12-bit registers and 16-bit register addresses, the register requests
are different and are directed at the device rather than interface, and
5 and 6-bit words are not supported.
The register layout is very similar to XR21B142X except that most
registers are offset by 0xc00 (corresponding to a channel index of 12 in
the MSB of wIndex). As the device is single-port so that the derived
channel index is 0, the current register accessors can be reused after
simply changing the address width.
Signed-off-by: Johan Hovold <johan@kernel.org>
The XR21B1421, XR21B1422 and XR21B1424 are the one-, two- and four-port
models of a second XR21B142X type of the Maxlinear/Exar USB UARTs.
The XR21B142X type differs from XR21V141X in several ways, including:
- register layout
- register width (16-bit instead of 8-bit)
- vendor register requests
- UART enable/disable sequence
- custom-driver mode flag
- three additional GPIOs (9 instead of 6)
As for XR21V141X, the XR21B142X vendor requests encode the channel index
in the MSB of wIndex, but it lacks the UART Manager registers which
have been replaced by regular UART registers. The new type also uses the
interface number of the control interface (0, 2, 4, 6) as channel index
instead of the channel number (0, 1, 2, 3).
The XR21B142X lacks the divisor and format registers used by XR21V141X
and instead uses the CDC SET_LINE_CONTROL request to configure the line
settings.
Note that the currently supported XR21V141X type lacks the custom-driver
mode flag that prevents the device from entering CDC-ACM mode when a CDC
requests is received. This specifically means that the SET_LINE_CONTROL
request cannot be used with XR21V141X even though it is otherwise
supported.
The UART enable sequence for XR21B142X does not involve explicitly
enabling the FIFOs, but according to datasheet the UART must be disabled
when writing any register but GPIO_SET, GPIO_CLEAR, TX_BREAK and
ERROR_STATUS.
Signed-off-by: Johan Hovold <johan@kernel.org>
There are at least four types of Maxlinear/Exar USB UARTs which differ
in various ways such as in their register layouts:
XR21V141X
XR21B142X
XR21B1411
XR22804
It is not clear whether the device type can be inferred from the
descriptors so encode it in the device-id table for now.
Add a type structure that can be used to abstract the register layout
and other features, and use it when accessing the XR21V141X UART
registers that are shared by all types.
Note that the currently supported XR21V141X type is the only type that
has a set of UART Manager registers and that these will need to be
handled specifically.
Similarly, XR21V141X is the only type which has the divisor registers
and that needs to use the format register when configuring the line
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation for adding support for further types, drop the type
prefix from defines that are not specific to XR21V141X.
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to configure the pins on every open and judging from the
vendor driver and datasheet it can be done before enabling the UART.
Move pin configuration from open() to port probe and make sure to
deassert DTR and RTS after configuring all pins as GPIO.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add support for the two- and four-port variants of XR21V1410.
Use the interface number of each control interface (e.g. 0, 2, 4, 6) to
derive the zero-based channel index:
XR21V1410 0
XR21V1412 0, 1
XR21V1414 0, 1, 2, 3
Note that the UART registers reside in separate blocks per channel,
while the UART Manager functionality is implemented using per-channel
registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove the random white space from the CSIZE switch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add two port-command helpers to handle the UART module-id parameter
instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make the vendor-request helpers data parameters be void pointers and
drop the caller casts.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop unnecessary packed attributes from structures that don't need it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop unnecessary packed attributes from structures that don't need it
and use the __packed macro consistently.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use kernel types consistently by replacing the remaining __uXX types.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a read-port-command helper analogous to the send-port-command
helper to take care of the UART module id instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a send-port-command helper which takes care of determining the UART
module id when sending commands instead of doing so at every call site.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the vendor-request helpers by using kernel-types consistently
and using void pointers for the data arguments, which allows removing
a cast from one caller.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Unlike the TUSB5052, the TUSB3410 has an LSR TEMT bit to tell if both
the transmitter data and shift registers are empty.
Make sure to check also the shift register on TUSB3410 when waiting for
the transmit buffer to drain during close and drop the time-based
one-char delay which is otherwise needed (e.g. 90 ms at 110 bps).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The three-character drain delay was added by commit f1175daa53 ("USB:
ti_usb_3410_5052: kill custom closing_wait") when removing the custom
closing-wait implementation, which used a fixed 20 ms poll period and
drain delay.
This was likely a bit too conservative as a one-character timeout (e.g.
33 ms at 300 bps) should be enough to compensate for the lack of a
transmitter empty bit in the TUSB5052 line-status register.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Document that the device line-status register doesn't tell when the
transmitter shift register has emptied and that this is why the
one-character drain delay is needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The f81232 driver now waits for the transmit FIFO to drain during close
so there is no need to keep the time-based drain delay, which would add
up to two seconds on every close for low line speeds.
Fixes: 98405f8103 ("USB: serial: f81232: add tx_empty function")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When dwc2 core is in clock gating mode loading driver
again causes driver fail. Because in that mode
registers are not accessible.
Added a flow of exiting clock gating mode
to avoid the driver reload failure.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073731.3C81BA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not hibernation nor partial power down are supported,
port resume is done using the clock gating programming flow.
Adds a new flow of exiting clock gating when PC is
resumed.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073723.BA0FEA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not hibernation nor partial power down are supported,
clock gating is used to save power.
Adds a new flow of entering clock gating when PC is
suspended.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073716.30C13A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When core is in clock gating state and an external
hub is connected, upper layer sends URB enqueue request,
which results in port reset issue.
Added exit from clock gating state to avoid port
reset issue and process upper layer request properly.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073708.ADFC6A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updates the implementation of exiting clock gating mode
when core receives port resume.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_exit_clock_gating()" function.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073701.367E0A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updates the implementation of entering clock gating mode
when core receives port suspend.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_enter_clock_gating()" function.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073653.9F493A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds clock gating exit flow when set port feature
reset is received in suspended state.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073646.27217A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added exit from clock gating mode when wakeup interrupt
is detected. To exit from the clock gating
in device mode "dwc2_gadget_exit_clock_gating()"
function is used with rem_wakeup parameter 0. To exit
clock gating in host mode "dwc2_host_exit_clock_gating()"
with rem_wakeup parameter 1.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073630.EF2CEA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If core doesn't support hibernation or partial power
down power saving options, power can still be saved
using clock gating on all the clocks.
- Added entering clock gating state from USB_SUSPEND
interrupt.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073623.65355A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added device clock gating support functions according
programming guide.
Moved "bus_suspended" flag to "dwc2_hsotg" struct because
we need to set that flag while entering to clock gating
in case when the driver is built in peripheral mode.
Added function names:
dwc2_gadget_enter_clock_gating()
dwc2_gadget_exit_clock_gating()
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073607.F41E8A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add recovery during resume if the controller was lost power at system suspend
- Reduce DMA memory footprint
- Other small improvements
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmB0S50ACgkQSFkpgVDW
cbthMggAnH0oPq93dipS9g2WhHxmwKGJimWTFU82RxuuX6MefvllXEkWCHJdPplp
dyKhzaFQxFksR7GJ8UCoZg3wg0rk38suLiN+W+k9re6QaHPFWJiMEm83mN3/YaNn
stVLiuMRl+VIApIIWbf3MW8/a3j9N5oRI+MbqmvhcA4TFu3Z1xTe9xhs8eDtzeUV
cGI6JbrZr5Q3pcsvvZPwj2nFgjJ7eYum9Z1CsAopHyVnYu/NK2jh2+W+L37dUSan
cwUOIRoNvSYNHyXFVszOEmfxtTAKiISQ7L4+8tXr4X+qC8tUNd8Rw1ow5BAo8gh+
bBL8+NZVVGoTvNpYPhLLUHncE5Fn9Q==
=+ZMP
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Several Cadence3 improvements are introduced in v5.13-rc1:
- Add recovery during resume if the controller was lost power at system suspend
- Reduce DMA memory footprint
- Other small improvements
* tag 'usb-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdnsp: Fixes issue with Configure Endpoint command
usb: cdnsp: remove redundant initialization of variable ret
usb: cdns3: delete repeated clear operations
usb: cdns3: Optimize DMA request buffer allocation
usb: cdns3: Use dma_pool_* api to alloc trb pool
usb: cdns3: fix static checker warning.
usb: cdns3: imx: mark cdns_imx_system_resume as __maybe_unused
usb: cdns3: trace: delete the trace parameter for request->trb
usb: cdns3: imx: add power lost support for system resume
usb: cdns3: add power lost support for system resume
Patch adds flag EP_UNCONFIGURED to detect whether endpoint was
unconfigured. This flag is set in cdnsp_reset_device after Reset Device
command. Among others this command disables all non control endpoints.
Flag is used in cdnsp_gadget_ep_disable to protect controller against
invoking Configure Endpoint command on disabled endpoint. Lack of this
protection in some cases caused that Configure Endpoint command completed
with Context State Error code completion.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The variable ret is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
dma_alloc_coherent already zeroes out memory, so memset is not needed.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
dma_alloc_coherent() might fail on the platform with a small
DMA region.
To avoid such failure in cdns3_prepare_aligned_request_buf(),
dma_alloc_coherent() is replaced with dma_alloc_noncoherent()
to allocate aligned request buffer of dynamic length.
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Allocation of DMA coherent memory in atomic context using
dma_alloc_coherent() might fail on platforms with smaller
DMA region.
To fix it, dma_alloc_coherent() is replaced with dma_pool
API to allocate a smaller chunk of DMA coherent memory for
TRB rings.
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The patch c450e48eb570: "usb: cdns3: add power lost support for
system resume" from Feb 18, 2021, leads to the following static
checker warning:
drivers/usb/cdns3/core.c:551 cdns_resume()
error: uninitialized symbol 'ret'.
drivers/usb/cdns3/core.c
544
545 if (!role_changed) {
546 if (cdns->role == USB_ROLE_HOST)
547 ret = cdns_drd_host_on(cdns);
548 else if (cdns->role == USB_ROLE_DEVICE)
549 ret = cdns_drd_gadget_on(cdns);
"ret" is uninitialized at else branch.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The function cdns_imx_system_resume() may have no callers depending
on configuration, so it must be marked __maybe_unused to avoid
harmless warning:
drivers/usb/cdns3/cdns3-imx.c:378:12: warning:
'cdns_imx_system_resume' defined but not used [-Wunused-function]
378 | static int cdns_imx_system_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~
Fixes: 67982dfa59de ("usb: cdns3: imx: add power lost support for system resume")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
It is not correct using %pa to print virtual address of request->trb, and
it is hard to print its physical address due to the virtual address is
zero before using. It could use index (start_trb/end_trb) to know the
current trb position, so no matter virtual address or physical address
for request-trb is not so meaningful.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
imx need special handle when controller lost power
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
If the controller lost its power during the system suspend, we need
to do all initialiation operations.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Add a debug printk to dump the GPIO configuration stored in EEPROM
during probe.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new GPIO valid-mask feature to inform gpiolib which pins are
available for use instead of handling that in a request callback.
This also allows user space to figure out which pins are available
through the chardev interface without having to request each pin in
turn.
Note that the return value when requesting an unavailable pin will now
be -EINVAL instead of -ENODEV.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add the missing unlock before return from function usbip_sockfd_store()
in the error handling case.
Fixes: bd8b820422 ("usbip: vudc synchronize sysfs code paths")
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408112305.1022247-1-yebin10@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In accordance with the USB HCD/DRD schema all the USB controllers are
supposed to have DT-nodes named with prefix "^usb(@.*)?". Since the
existing DT-nodes will be renamed in a subsequent patch let's fix the DWC3
Qcom-specific code to detect the DWC3 sub-node just by checking its
compatible string to match the "snps,dwc3". The semantic of the code
won't change seeing all the DWC USB3 nodes are supposed to have the
compatible property with any of those strings set.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210409113029.7144-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210410024818.65659-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return the exactly delay time given by root hub descriptor,
this helps to reduce resume time etc.
Due to the root hub descriptor is usually provided by the host
controller driver, if there is compatibility for a root hub,
we can fix it easily without affect other root hub
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618017645-12259-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.
When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.
Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port struct device rather than tty class device for debugging.
Note that while USB serial doesn't support serdev yet (due to serdev not
handling hotplugging), serdev ttys do not have a corresponding class
device and would have been logged using a "(NULL device *):" prefix.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when it is
not used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected, but might as well be left unset when it is not
known (which is the case for CDC).
Fix the cdc-acm TIOCGSERIAL implementation by dropping its custom
interpretation of the unused xmit_fifo_size and baud_base fields, which
overflowed the former with the URB buffer size and set the latter to the
current line speed. Also return the port line number, which is the only
other value used besides the close parameters.
Note that the current line speed can still be retrieved through the
standard termios interfaces.
Fixes: 18c75720e6 ("USB: allow users to run setserial with cdc-acm")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b401f8c4f4.
The offending commit claimed that trying to set the values reported back
by TIOCGSERIAL as a regular user could result in an -EPERM error when HZ
is 250, but that was never the case.
With HZ=250, the default 0.5 second value of close_delay is converted to
125 jiffies when set and is converted back to 50 centiseconds by
TIOCGSERIAL as expected (not 12 cs as was claimed, even if that was the
case before an earlier fix).
Comparing the internal current and new jiffies values is just fine to
determine if the value is about to change so drop the bogus workaround
(which was also backported to stable).
For completeness: With different default values for these parameters or
with a HZ value not divisible by two, the lack of rounding when setting
the default values in tty_port_init() could result in an -EPERM being
returned, but this is hardly something we need to worry about.
Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for altmodes described in the usb-connector fwnode
associated with the Type-C controller by calling the new
typec_port_register_altmodes_from_fwnode() helper for this.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This can be used by Type-C controller drivers which use a standard
usb-connector fwnode, with altmodes sub-node, to describe the available
altmodes.
Note there are is no devicetree bindings documentation for the altmodes
node, this is deliberate. ATM the fwnodes used to register the altmodes
are only used internally to pass platform info from a drivers/platform/x86
driver to the type-c subsystem.
When a devicetree user of this functionally comes up and the dt-bindings
have been hashed out the internal use can be adjusted to match the
dt-bindings.
Currently the typec_port_register_altmodes() function expects
an "altmodes" child fwnode on port->dev with this "altmodes" fwnode having
child fwnodes itself with each child containing 2 integer properties:
1. A "svid" property, which sets the id of the altmode, e.g. displayport
altmode has a svid of 0xff01.
2. A "vdo" property, typically used as a bitmask describing the
capabilities of the altmode, the bits in the vdo are specified in the
specification of the altmode.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_role_switch_find_by_fwnode() returns a reference to the role-switch
which must be put by calling usb_role_switch_put().
usb_role_switch_put() calls module_put(sw->dev.parent->driver->owner),
add a matching try_module_get() to usb_role_switch_find_by_fwnode(),
making it behave the same as the other usb_role_switch functions
which return a reference.
This avoids a WARN_ON being hit at kernel/module.c:1158 due to the
module-refcount going below 0.
Fixes: c6919d5e0c ("usb: roles: Add usb_role_switch_find_by_fwnode()")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409124136.65591-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clocks are configured by devm_clk_bulk_get_all() in this driver. In
case of any error the clocks freeing will be handled automatically.
There is no need to explicitly free the clocks. Fix the same.
Fixes: 84770f028f ("usb: dwc3: Add driver for Xilinx platforms")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1617904448-74611-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel-doc run gave a warning for Xilinx DWC3 driver:
drivers/usb/dwc3/dwc3-xilinx.c:27: warning: expecting prototype for
dwc3(). Prototype was for XLNX_USB_PHY_RST_EN() instead
Basically it was due to an extra '*' in line:2. This patch fixes the same.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1617904448-74611-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408130831.56239-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408091836.55227-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092947.3271507-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mutex lock can be initialized automatically with DEFINE_MUTEX()
rather than explicitly calling mutex_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20210405101434.14878-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to platform_get_resource can potentially return a NULL pointer
on failure, so add this check and return -EINVAL if it fails.
Fixes: c41442474a ("usb: gadget: R8A66597 peripheral controller support.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Dereference null return")
Link: https://lore.kernel.org/r/20210406184510.433497-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The connectors may be registered after the ports, so the
"connector" links need to be created for the ports also when
ever a new connector gets registered.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407065555.88110-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing usb_for_each_port(). It works the same way as
usb_for_each_dev(), but instead of going through every USB
device in the system, it walks through the USB ports in the
system.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407065555.88110-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding functions that can be used to link/unlink ports -
USB ports, TBT3/USB4 ports, DisplayPorts and so on - to
the USB Type-C connectors they are attached to inside a
system. The symlink that is created for the port device is
named "connector".
Initially only ACPI is supported. ACPI port object shares
the _PLD (Physical Location of Device) with the USB Type-C
connector that it's attached to.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407065555.88110-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
power_supply_changed needs to be called to notify clients
after the partner accepts the requested values for the pps
case.
Also, remove the redundant power_supply_changed at the end
of the tcpm_reset_port as power_supply_changed is already
called right after usb_type is changed.
Fixes: f2a8aa053c ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_pd_select_pps_apdo overwrites port->pps_data.min_volt,
port->pps_data.max_volt, port->pps_data.max_curr even before
port partner accepts the requests. This leaves incorrect values
in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values in req_min_volt, req_max_volt, req_max_curr, req_out_volt,
req_op_curr. min_volt, max_volt, max_curr gets updated once the
partner accepts the request. current_limit, supply_voltage gets updated
once local port's tcpm enters SNK_TRANSITION_SINK when the accepted
current_limit and supply_voltage is enforced.
Fixes: f2a8aa053c ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_pd_build_request overwrites current_limit and supply_voltage
even before port partner accepts the requests. This leaves stale
values in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values of current limit/supply voltage in req_current_limit
and req_supply_voltage. current_limit/supply_voltage gets updated
once the port partner accepts the request.
Fixes: f2a8aa053c ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc2 core is in partial power down mode
loading driver again causes driver fail. Because in
that mode registers are not accessible.
Added a flow of exiting the partial power down mode
to avoid the driver reload failure.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094615.8AE35A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the implementation of exiting from partial power down
power saving mode when PC is resumed.
Added port connection status checking which prevents exiting from
Partial Power Down mode from _dwc2_hcd_resume() if not in Partial
Power Down mode.
Rearranged the implementation to get rid of many "if"
statements.
NOTE: Switch case statement is used for hibernation partial
power down and clock gating mode determination. In this patch
only Partial Power Down is implemented the Hibernation and
clock gating implementations are planned to be added.
Fixes: 6f6d70597c ("usb: dwc2: bus suspend/resume for hosts with DWC2_POWER_DOWN_PARAM_NONE")
Cc: <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094607.1A9BAA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With current implementation the port power is being disabled,
which is not required by the programming guide. Also, if there
is a system which works only in "DWC2_POWER_DOWN_PARAM_NONE"
(clock gating) mode the current implementation does not set
Gate hclk bit in pcgctl register.
Rearranges and updates the implementation of entering to partial
power down power saving mode when PC is suspended to get
rid of many "if" statements and removes disabling of port power.
NOTE: Switch case statement is used for hibernation partial
power down and clock gating mode determination. In this patch
only Partial Power Down is implemented the Hibernation and
clock gating implementations are planned to be added.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094559.33541A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to programming guide in host mode, port
power must be turned on in session request
interrupt handlers.
Fixes: 21795c826a ("usb: dwc2: exit hibernation on session request")
Cc: <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094550.75484A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When core is in partial power down state and an external
hub is connected, upper layer sends URB enqueue request,
which results in port reset issue.
Added exit from partial power down state to avoid port
reset issue and process upper layer request correctly.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094542.685BAA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before changing to connector B exiting from Partial
Power Down is required.
- Added exiting from Partial Power Down mode when
connector ID status changes to "connId B".
Because if connector ID status changed to B connector
while core was in partial power down mode, HANG would
accrue from a soft reset.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094534.4AA7AA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds Partial Power Down exiting flow when set port feature
reset is received in suspended state.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094526.4DD7AA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added flow of exiting Partial Power Down in
"dwc2_port_resume()" function when core receives resume.
NOTE: Switch case statement is used for hibernation partial
power down and clock gating mode determination. In this patch
only Partial Power Down is implemented the Hibernation and
clock gating implementations are planned to be added.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094518.6DA1DA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds flow of entering Partial Power Down in
"dwc2_port_suspend()" function when core receives suspend.
NOTE: Switch case statement is used for hibernation partial
power down and clock gating mode determination. In this patch
only Partial Power Down is implemented the Hibernation and
clock gating implementations are planned to be added.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094510.6C4E9A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Earlier "dwc2_port_suspend()" and "dwc2_port_resume()" functions
were implemented without proper description and host or device mode
difference.
- Added "dwc2_port_suspend" and "dwc2_port_resume" functions to
"core.h" header file.
- Updated function description in documentation.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094502.61D18A0232@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to programming guide added host partial power
down exit flow in wakeup detected interrupt handler.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094454.5BBCBA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are wrapper functions which are calling device or host
enter/exit partial power down functions.
This change is done because we need to separate device and
host partial power down functions as the programming flow
has a lot of difference between host and device. With this
update during partial power down exit driver relies on
backup value of "GOTGCTL_CURMODE_HOST" to determine the
mode of core before entering to PPD.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094446.6491BA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For host mode Partial Power Down entering and exiting
separate functions are needed to implement the logic.
Earlier the logic was implemented in one function. Which was
confusing the readability. Also both host and device implementations
were in the same function.
- Added host partial power down functions which must be called
by dwc2_enter_partial_power_down()/dwc2_exit_partial_power_down()
functions.
Added function names:
dwc2_host_enter_partial_power_down()
dwc2_host_exit_partial_power_down()
NOTE: There is a checkpatch "CHECK" warning on "udelay(100)".
The delay is needed to properly exit gadget Partial Power Down
A delay less than 100 doesn't work.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094438.56CFBA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For device mode Partial Power Down entering and exiting
separate functions are needed to implement the logic.
Earlier the logic was implemented in one function. Which was
confusing the readability. Also both host and device implementations
were in the same function.
- Added device partial power down functions which must be called
by dwc2_enter_partial_power_down()/dwc2_exit_partial_power_down()
functions.
- Added "in_ppd" flag in "dwc2_hsotg" struct to indicate the
core state after entering into partial power down mode.
Added function names:
dwc2_gadget_enter_partial_power_down()
dwc2_gadget_exit_partial_power_down()
NOTE: There is a checkpatch "CHECK" warning on "udelay(100)".
The delay is needed to properly exit gadget Partial Power Down
A delay less than 100 doesn't work.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094430.383B9A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop unused definitions relating to a never mainlined custom
proc-interface and some likewise unused string descriptor definitions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Switch to using the system-wide default 30-second closing-wait timeout
instead of the driver specific 40-second timeout.
The timeout can be changed per port using TIOCSSERIAL (setserial) if
needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The ti_usb_3410_5052 has supported changing the closing_wait parameter
through TIOCSSERIAL (setserial) for about a decade and commit
f1175daa53 ("USB: ti_usb_3410_5052: kill custom closing_wait").
It's time to drop the corresponding driver-specific module parameter.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Switch to using the system-wide default 30-second closing-wait timeout
instead of the driver specific 40-second timeout.
The timeout can be changed per port using TIOCSSERIAL (setserial) if
needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that all USB serial drivers supports setting the closing_wait
parameter through TIOCSSERIAL (setserial) it's time to drop the
corresponding io_ti module parameter.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The TIOCSSERIAL implementation needs to compare the old flag and divisor
settings with the new to detect ASYNC_SPD changes, but there's no need
to copy all driver state to the stack for that.
While at it, unbreak the function parameter list.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Changing the deprecated custom_divisor field is an unprivileged
operation so after verifying that flag field does not contain any
privileged changes both updates can be carried out by any user.
Combine the two branches and drop the erroneous comment.
Note that private flags field is only used for ASYNC flags so there's no
need to try to retain any other bits when updating the flags.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The TIOCSSERIAL error handling is inconsistent at best, but drivers tend
to ignore requests to change parameters which cannot be changed rather
than return an error.
The FTDI driver ignores change requests for all immutable parameters but
baud_base so return success also in this case for consistency.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The TIOCGSERIAL ioctl can be used to set and retrieve the UART type for
legacy UARTs, but some USB serial drivers have been reporting back
random types in order to "make user-space happy".
Some applications have historically expected TIOCGSERIAL to be
implemented, but judging from the Debian sources, the port type not
being PORT_UNKNOWN is only used to check for the existence of legacy
serial ports (ttySn).
Drivers like ftdi_sio have been using PORT_UNKNOWN for twenty years (and
option for 10 years) without anyone complaining so let's stop reporting
back anything else.
In the unlikely event that this do cause problems, this should be fixed
tree-wide anyway (e.g. for all USB serial drivers and also CDC-ACM).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The closing_wait parameter determines how long to wait for the transfer
buffers to drain during close and the default timeout of 30 seconds may
not be sufficient at low line speeds. In other cases, when for example
flow is stopped, the default timeout may instead be too long.
Add generic support for TIOCSSERIAL and TIOCGSERIAL with handling of the
three common parameters close_delay, closing_wait and line for the
benefit of all USB serial drivers while still allowing drivers to
implement further functionality through the existing callbacks.
This currently includes a few drivers that report their base baud clock
rate even if that is really only of interest when setting custom
divisors through the deprecated ASYNC_SPD_CUST interface; an interface
which only the FTDI driver actually implements.
Some drivers have also been reporting back a fake UART type, something
which should no longer be needed and will be dropped by a follow-on
patch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drivers should return -ENOTTY ("Inappropriate I/O control operation")
when an ioctl isn't supported, while -EINVAL is used for invalid
arguments.
Fix up the TIOCMGET, TIOCMSET and TIOCGICOUNT helpers which returned
-EINVAL when a USB serial driver did not implement the corresponding
methods.
Note that the TIOCMGET and TIOCMSET helpers predate git and do not get a
corresponding Fixes tag below.
Fixes: d281da7ff6 ("tty: Make tiocgicount a handler")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The baud_base parameter could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
Fix the usb_wwan TIOCGSERIAL implementation by dropping its custom
interpretation of the unused port and baud_base fields, which were set
to the port index and current line speed, respectively.
Fixes: 02303f7337 ("usb-wwan: implement TIOCGSERIAL and TIOCSSERIAL to avoid blocking close(2)")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the usb_wwan implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: 02303f7337 ("usb-wwan: implement TIOCGSERIAL and TIOCSSERIAL to avoid blocking close(2)")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The port close_delay and closing_wait parameters set by TIOCSSERIAL are
specified in jiffies and not milliseconds.
Add the missing conversions so that the TIOCSSERIAL works as expected
also when HZ is not 1000.
Fixes: 02303f7337 ("usb-wwan: implement TIOCGSERIAL and TIOCSSERIAL to avoid blocking close(2)")
Cc: stable@vger.kernel.org # 2.6.38
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Changing the port closing-wait parameter is a privileged operation so
make sure to return -EPERM if a regular user tries to change it.
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
close_delay, but let's report back the default value actually used (0.5
seconds).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Fixes: 52af954599 ("USB: add USB serial ssu100 driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The baud_base parameter could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
these, but let's report back the default values actually used (0.5 and
30 seconds, respectively).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Fixes: faac64ad9c ("USB: serial: opticon: add serial line ioctls")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Fixes: 0f64478cbc ("USB: add USB serial mos7720 driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing close_delay, but let's report back the default value actually
used (0.5 seconds).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the uart base clock when it
could not be detected, but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The FTDI driver is the only USB serial driver supporting the deprecated
ASYNC_SPD flags, which are reported back as they should by TIOCGSERIAL,
but the returned parameters did not include the line number.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
these, but let's report back the default values actually used (0.5 and
30 seconds, respectively).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
these, but let's report back the default values actually used (0.5 and
30 seconds, respectively).
Fixes: aac1fc386f ("USB: serial: add Fintek F81232 usb to serial driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
these, but let's report back the default values actually used (0.5 and
30 seconds, respectively).
Fixes: aac1fc386f ("USB: serial: add Fintek F81232 usb to serial driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The baud_base parameter could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
these, but let's report back the default values actually used (0.5 and
30 seconds, respectively).
Fixes: 2f430b4bba ("USB: ark3116: Add TIOCGSERIAL and TIOCSSERIAL ioctl calls.")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The same values are parsed several times from transfer and event
TRBs by different functions in the same call path, all while processing
one transfer event.
As the TRBs are in DMA memory and can be accessed by the xHC host we want
to avoid this to prevent double-fetch issues.
To resolve this pass the already parsed values to the different functions
in the path of parsing a transfer event
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210406070208.3406266-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Max Interrupters supported by the controller is given in a 10bit
wide bitfield, but the driver uses a fixed 128 size array to index these
interrupters.
Klockwork reports a possible array out of bounds case which in theory
is possible. In practice this hasn't been hit as a common number of Max
Interrupters for new controllers is 8, not even close to 128.
This needs to be fixed anyway
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210406070208.3406266-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is only to make the handling of the class consistent
with the two other susbsystems - the alt mode bus and the
mux class.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210401105847.13026-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fuzzing uncovered race condition between sysfs code paths in usbip
drivers. Device connect/disconnect code paths initiated through
sysfs interface are prone to races if disconnect happens during
connect and vice versa.
This problem is common to all drivers while it can be reproduced easily
in vhci_hcd. Add a sysfs_lock to usbip_device struct to protect the paths.
Use this in vhci_hcd to protect sysfs paths. For a complete fix, usip_host
and usip-vudc drivers and the event handler will have to use this lock to
protect the paths. These changes will be done in subsequent patches.
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+a93fba6d384346a761e3@syzkaller.appspotmail.com
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/b6568f7beae702bbc236a545d3c020106ca75eac.1616807117.git.skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmBnsXkACgkQSFkpgVDW
cbvHhwf/Qz/B3QY+D4nedwuwJJNk021/9cjkQ6X7whvh4c1qAgmw3j73WrbSVsyd
m45atawjE7uKsBTouh6fJoHId5uNKE6zpHtjMP6WDC1xcrHqMXW3WLyCxf84i5OC
RWRVmGs/DHDAamVrpUGpcEulp6Ih+TvzlRUsRzHLc3BRxfphq6CYg0XhRKJMK/7r
YvpkhtwmqVppyrgUr8Xm2e++qMZWwHHBmBo+rf8/BkctKaLlJotuXTioUH68JchO
iYtPl/QmsFNIB7ewVZFAjjIKqyqzcmY9tXlCcg6mLn05fOQzIcic9h0y9ArbAd/+
VmlDUNw0F8+4ix5MCdLuCdrhYxJYrw==
=OrtC
-----END PGP SIGNATURE-----
Merge tag 'v5.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Fixes one issue with dequeuing requests after disabling endpoint for cdnsp udc driver
* tag 'v5.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdnsp: Fixes issue with dequeuing requests after disabling endpoint
The xHCI driver support usb2 HW LPM by default, here add support
XHCI_HW_LPM_DISABLE quirk, then we can disable usb2 lpm when
need it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1617181553-3503-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MediaTek 0.96 xHCI controller on some platforms does not
support bulk stream even HCCPARAMS says supporting, due to MaxPSASize
is set a default value 1 by mistake, here use XHCI_BROKEN_STREAMS
quirk to fix it.
Fixes: 94a631d91a ("usb: xhci-mtk: check hcc_params after adding primary hcd")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1617181553-3503-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The oops happens when unbind driver through sysfs as following,
because xhci_mtk_drop_ep() try to drop the endpoint of root hub
which is not added by xhci_add_endpoint() and the virtual device
is not allocated, in fact also needn't drop it, so should skip it.
Call trace:
xhci_mtk_drop_ep+0x1b8/0x298
usb_hcd_alloc_bandwidth+0x1d8/0x380
usb_disable_device_endpoints+0x8c/0xe0
usb_disable_device+0x128/0x168
usb_disconnect+0xbc/0x2c8
usb_remove_hcd+0xd8/0x210
xhci_mtk_remove+0x98/0x108
platform_remove+0x28/0x60
device_release_driver_internal+0x110/0x1e8
device_driver_detach+0x18/0x28
unbind_store+0xd4/0x108
drv_attr_store+0x24/0x38
Fixes: 14295a1500 ("usb: xhci-mtk: support to build xhci-mtk-hcd.ko")
Reported-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1617179142-2681-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The remainder of the last bandwidth bugdget is wrong,
it's the value alloacted in last bugdget, not unused.
Reported-by: Yaqii Wu <Yaqii.Wu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1617179142-2681-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IS_ERR() and PTR_ERR() use wrong pointer, it should be
udc->virt_addr, fix it.
Fixes: 1b9f35adb0 ("usb: gadget: udc: Add Synopsys UDC Platform driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210330130159.1051979-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just fix the following checkpatch error:
ERROR: Macros with complex values should be enclosed in parentheses.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Link: https://lore.kernel.org/r/1617001556-61868-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the virtual port_dev device is passed to DMA API, and this is
wrong because the device passed to DMA API calls must be the actual
hardware device performing the DMA.
The patch replaces usb_gadget_map_request/usb_gadget_unmap_request APIs
with usb_gadget_map_request_by_dev/usb_gadget_unmap_request_by_dev APIs
so the DMA capable platform device can be passed to the DMA APIs.
The patch fixes below backtrace detected on Facebook AST2500 OpenBMC
platforms:
[<80106550>] show_stack+0x20/0x24
[<80106868>] dump_stack+0x28/0x30
[<80823540>] __warn+0xfc/0x110
[<8011ac30>] warn_slowpath_fmt+0xb0/0xc0
[<8011ad44>] dma_map_page_attrs+0x24c/0x314
[<8016a27c>] usb_gadget_map_request_by_dev+0x100/0x1e4
[<805cedd8>] usb_gadget_map_request+0x1c/0x20
[<805cefbc>] ast_vhub_epn_queue+0xa0/0x1d8
[<7f02f710>] usb_ep_queue+0x48/0xc4
[<805cd3e8>] ecm_do_notify+0xf8/0x248
[<7f145920>] ecm_set_alt+0xc8/0x1d0
[<7f145c34>] composite_setup+0x680/0x1d30
[<7f00deb8>] ast_vhub_ep0_handle_setup+0xa4/0x1bc
[<7f02ee94>] ast_vhub_dev_irq+0x58/0x84
[<7f0309e0>] ast_vhub_irq+0xb0/0x1c8
[<7f02e118>] __handle_irq_event_percpu+0x50/0x19c
[<8015e5bc>] handle_irq_event_percpu+0x38/0x8c
[<8015e758>] handle_irq_event+0x38/0x4c
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20210331045831.28700-1-rentao.bupt@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when dwc3 handles request cancelled, dwc3 just returns
-ECONNRESET for all requests. It will cause USB function drivers
can't know if the requests are cancelled by other reasons.
This patch will replace DWC3_REQUEST_STATUS_CANCELLED with the
reasons below.
- DWC3_REQUEST_STATUS_DISCONNECTED
- DWC3_REQUEST_STATUS_DEQUEUED
- DWC3_REQUEST_STATUS_STALLED
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Ray Chi <raychi@google.com>
Link: https://lore.kernel.org/r/20210327181742.1810969-1-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/usb/dwc3/dwc3-exynos.c follows this syntax, but the
content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc:
"warning: expecting prototype for dwc3(). Prototype was for DWC3_EXYNOS_MAX_CLOCKS() instead"
Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210329140318.27742-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
There are certain files in drivers/usb/dwc3, which follow this syntax,
but the content inside does not comply with kernel-doc.
Such lines were probably not meant for kernel-doc parsing, but are parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warnings from kernel-doc.
E.g., presence of kernel-doc like comment in drivers/usb/dwc3/io.h at
header causes this warnings by kernel-doc:
"warning: expecting prototype for h(). Prototype was for __DRIVERS_USB_DWC3_IO_H() instead"
Similarly for other files too.
Provide a simple fix by replacing such occurrences with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210329135108.27128-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/usb/dwc3/dwc3-st.c follows this syntax, but the
content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc:
"warning: expecting prototype for dwc3(). Prototype was for CLKRST_CTRL() instead"
Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210329132014.24304-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/usb/dwc3/dwc3-imx8mp.c follows this syntax, but the
content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc:
"warning: expecting prototype for dwc3(). Prototype was for USB_WAKEUP_CTRL() instead"
Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210329142604.28737-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new multi-interface support in USB serial core to properly claim
also the control interface during probe. This prevents having another
driver claim the control interface and makes core allocate resources
also for the interrupt endpoint (currently unused).
Switch to probing only Communication Class interfaces and use the Union
functional descriptor to determine the corresponding data interface.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A single USB function can be implemented using a group of interfaces and
this is for example commonly used for Communication Class devices.
Add support for multi-interface functions to USB serial core and export
an interface that allows drivers to claim a second sibling interface.
The interface could easily be extended to allow claiming further
interfaces if ever needed.
When a driver claims a sibling interface in probe(), core allocates
resources for any bulk in, bulk out, interrupt in and interrupt out
endpoints found also on the sibling interface.
Disconnect is implemented so that unbinding either interface will
release the other interface while disconnect() is called precisely once.
Similarly, suspend() is called when the first sibling interface is
suspended and resume() is called when the last sibling interface is
resumed by USB core.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Refactor endpoint classification and replace the build-time
endpoint-array sanity checks with runtime checks in preparation for
handling endpoints from a sibling interface.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The suspending flag was added back in 2009 but no users ever followed.
Remove it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The XR21V141X does not have a 5- or 6-bit mode, but the current
implementation failed to properly restore the old setting when CS5 or
CS6 was requested. Instead an invalid request would be sent to the
device.
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan@kernel.org>
The variable error is initialized to 0 and is set to 1 this
value is never read as it is on an immediate return path. The
only read of error is to check it is 0 and this check is always
true at that point of the code. The variable is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some 'clk_prepare_enable()' and 'clk_get()' must be undone in the error
handling path of the probe function, as already done in the remove
function.
Fixes: 3fc154b6b8 ("USB Gadget driver for Samsung s3c2410 ARM SoC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/2bee52e4ce968f48b4c32545cf8f3b2ab825ba82.1616830026.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 188db4435a ("usb: gadget: s3c: use platform resources"),
'request_mem_region()' and 'ioremap()' are no more used, so they don't need
to be undone in the error handling path of the probe and in the remove
function.
Remove these calls and the unneeded 'rsrc_start' and 'rsrc_len' global
variables.
Fixes: 188db4435a ("usb: gadget: s3c: use platform resources")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/b317638464f188159bd8eea44427dd359e480625.1616830026.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newer usb_control_msg_{send|recv}() API ensures that a short read is
treated as an error, data can be used off the stack, and raw usb pipes
need not be created in the calling functions.
For this reason, instances of usb_control_msg() have been replaced with
usb_control_msg_send() appropriately.
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20210326223251.753952-4-anant.thazhemadam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newer usb_control_msg_{send|recv}() API ensures that a short read is
treated as an error, data can be used off the stack, and raw usb pipes need
not be created in the calling functions.
For this reason, the instance of usb_control_msg() has been replaced with
usb_control_msg_send() appropriately.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20210326223251.753952-3-anant.thazhemadam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newer usb_control_msg_{send|recv}() API ensures that a short read
is treated as an error, data can be used off the stack, and raw usb
pipes need not be created in the calling functions.
For this reason, instances of usb_control_msg() have been replaced with
usb_control_msg_{recv|send}() appropriately.
Now, we also test for a short device descriptor (which USB core
should already have fetched if you get to probe this driver), but which
wasn't verified again here before.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20210326223251.753952-2-anant.thazhemadam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, vbus_draw callback used wrong scale for power_supply.
The unit of power supply should be uA.
Therefore, this patch will fix this problem.
Fixes: 99288de360 ("usb: dwc3: add an alternate path in vbus_draw callback")
Reported-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ray Chi <raychi@google.com>
Link: https://lore.kernel.org/r/20210327182809.1814480-2-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In host mode port connection status flag is "0" when loading
the driver. After loading the driver system asserts suspend
which is handled by "_dwc2_hcd_suspend()" function. Before
the system suspend the port connection status is "0". As
result need to check the "port_connect_status" if it is "0",
then skipping entering to suspend.
Cc: <stable@vger.kernel.org> # 5.2
Fixes: 6f6d70597c ("usb: dwc2: bus suspend/resume for hosts with DWC2_POWER_DOWN_PARAM_NONE")
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210326102510.BDEDEA005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increased the waiting timeout for HPRT0.PrtSusp register field
to be set, because on HiKey 960 board HPRT0.PrtSusp wasn't
generated with the existing timeout.
Cc: <stable@vger.kernel.org> # 4.18
Fixes: 22bb5cfdf1 ("usb: dwc2: Fix host exit from hibernation flow.")
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210326102447.8F7FEA005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pinephone running on Allwinner A64 fails to suspend with USB devices
connected as reported by Bhushan Shah <bshah@kde.org>. Reverting
commit 5fbf7a2534 ("usb: musb: fix idling for suspend after
disconnect interrupt") fixes the issue.
Let's add suspend checks also for suspend after disconnect interrupt
quirk handling like we already do elsewhere.
Fixes: 5fbf7a2534 ("usb: musb: fix idling for suspend after disconnect interrupt")
Reported-by: Bhushan Shah <bshah@kde.org>
Tested-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210324071142.42264-1-tony@atomide.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MediaTek 0.96 xHCI controller on some platforms does not
support bulk stream even HCCPARAMS says supporting, due to MaxPSASize
is set a default value 1 by mistake, here use XHCI_BROKEN_STREAMS
quirk to fix it.
Fixes: 94a631d91a ("usb: xhci-mtk: check hcc_params after adding primary hcd")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that dep->flags are cleared until after stop active transfers
is completed. Otherwise, the ENDXFER command will not be executed
during ep disable.
Fixes: f09ddcfcb8 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616610664-16495-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support ip-sleep wakeup for MT8183, it's similar to MT8173,
and it's also a specific one, but not following IPM rule.
Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~10 for later
revision that follows the IPM rule.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support ip-sleep wakeup for MT8183, it's similar to MT8173,
and it's also a specific one, but not following IPM rule.
Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~10 for
later revision that follows the IPM rule.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need DMI to identify Intel Minnowboard (v1) since it has
properly set PCI sub IDs. So, drop unneeded DMI level of identification.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210325135508.70350-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use __maybe_unused for the suspend()/resume() hooks and get rid of
the CONFIG_PM_SLEEP ifdefery to improve the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210325135508.70350-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A short packet indicates the end of a transfer and marks the request as
complete.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-8-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this, it wrote as much as available into the buffer, even if it
didn't fit.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-7-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently it leaves unhandled interrupts unmasked, but those are never
acked. In the case of a "device idle" interrupt, this leads to an
effectively frozen system until plugging it in.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-5-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the EP0 IN request was not completed but less than a packet sent,
it would complete the request successfully. That doesn't make sense
and can't really happen as fotg210_start_dma always sends
min(length, maxpkt) bytes.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-4-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a 134 Byte packet, it sends the first two 64 Byte packets just fine,
but then notice that less than a packet is remaining and call fotg210_done
without actually sending the rest.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-3-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a 75 Byte request, it would send the first 64 separately, then detect
that the remaining 11 Byte fit into a single DMA, but due to this bug set
the length to the original 75 Bytes. This leads to a DMA failure (which is
ignored...) and the request completes without the remaining bytes having
been sent.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-2-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently dwc3 only prints the virtual address of a register when doing
register read/write. However, these hashed addresses are difficult to read.
Also, since we use %p, we may get some useless (___ptrval___) prints if the
address is not randomized enough. Let's include the register offset to help
read the register read and write tracepoints.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cb38aa7dec109a8965691b53039a8b317d026189.1616636706.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sparse tool complains as follows:
drivers/usb/typec/tcpm/tcpci_maxim.c:55:34: warning:
symbol 'max_tcpci_tcpci_write_table' was not declared. Should it be static?
This symbol is not used outside of tcpci_maxim.c, so this
commit marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210324144253.1011234-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Minnowboard (v1) uses SCH GPIO line SUS7 (i.e. 12)
for VBUS sense. Provide a DMI based quirk to have it's being used.
Fixes: e20849a8c8 ("usb: gadget: pch_udc: Convert to use GPIO descriptors")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During conversion to use GPIO descriptors the device pointer,
which is applied to devm_gpiod_get(), is not yet initialized.
Move initialization in the ->probe() in order to have it set before use.
Fixes: e20849a8c8 ("usb: gadget: pch_udc: Convert to use GPIO descriptors")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a121 completely.
While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.
Fixes: d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
Fixes: 9903b6bedd ("usb: gadget: pch-udc: fix lock")
Fixes: 1d23d16a88 ("usb: gadget: pch_udc: reorder spin_[un]lock to avoid deadlock")
Cc: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel doc and the content described by it shouldn't be torn apart.
Otherwise validator is not happy:
.../pch_udc.c:573: warning: expecting prototype for pch_udc_reconnect(). Prototype was for pch_udc_init() instead
Fixes: 1c575d2d2e ("usb: gadget: pch_udc: Fix usb/gadget/pch_udc: Fix ether gadget connect/disconnect issue")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA mapping might fail, we have to check it with dma_mapping_error().
Otherwise DMA-API is not happy:
DMA-API: pch_udc 0000:02:02.4: device driver failed to check map error[device address=0x00000000027ee678] [size=64 bytes] [mapped as single]
Fixes: abab0c67c0 ("usb: pch_udc: Fixed issue which does not work with g_serial")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have a separate routine for VBUS sense, the interrupt may occur
before gadget driver is present. Hence, ->setup() call may oops the kernel:
[ 55.245843] BUG: kernel NULL pointer dereference, address: 00000010
...
[ 55.245843] EIP: pch_udc_isr.cold+0x162/0x33f
...
[ 55.245843] <IRQ>
[ 55.245843] ? pch_udc_svc_data_out+0x160/0x160
Check if driver is present before calling ->setup().
Fixes: f646cf9452 ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Either way ~0 will be in the correct byte order, hence
replace cpu_to_le32() by lower_32_bits(). Moreover,
it makes sparse happy, otherwise it complains:
.../pch_udc.c:1813:27: warning: incorrect type in assignment (different base types)
.../pch_udc.c:1813:27: expected unsigned int [usertype] dataptr
.../pch_udc.c:1813:27: got restricted __le32 [usertype]
Fixes: f646cf9452 ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current xhci_create_usb3_bos_desc() uses a static bos u8 array and
various magic numbers and offsets making it difficult to extend support
for USB 3.2. Let's rewrite this entire function to support dual-lane in
USB 3.2.
The hub driver matches the port speed ID from the extended port status
to the SSID of the sublink speed attributes to detect if the device
supports SuperSpeed Plus. Currently we don't provide the default gen1x2
and gen2x2 sublink speed capability descriptor for USB 3.2 roothub. The
USB stack depends on this to detect and match the correct speed.
In addition, if the xHCI host provides Protocol Speed ID (PSI)
capability, then make sure to convert Protocol Speed ID Mantissa and
Exponent (PSIM & PSIE) to lane speed for gen1x2 and gen2x2.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/19cd09b03f96346996270579fd27d38b8a6844aa.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some hosts incorrectly use sub-minor version for minor version (i.e.
0x02 instead of 0x20 for bcdUSB 0x320 and 0x01 for bcdUSB 0x310).
Currently the xHCI driver works around this by just checking for minor
revision > 0x01 for USB 3.1 everywhere. With the addition of USB 3.2,
checking this gets a bit cumbersome. Since there is no USB release with
bcdUSB 0x301 to 0x309, we can assume that sub-minor version 01 to 09 is
incorrect. Let's try to fix this and use the minor revision that matches
with the USB/xHCI spec to help with the version checking within the
driver.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ed330e95a19dc367819c5b4d78bf7a541c35aa0a.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/function/f_fs.c:3829:8-15: WARNING opportunity for memdup_user
Use memdup_user rather than duplicating its implementation
This is a little bit restricted to reduce false positives
Generated by: scripts/coccinelle/api/memdup_user.cocci
Fixes: 8704fd73bf ("USB: gadget: f_fs: remove likely/unlikely")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210308070951.GA83949@8a16bdd473dc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When usb_otg_descriptor_alloc() returns NULL to usb_desc, no error
return code of msg_bind() is assigned.
To fix this bug, status is assigned with -ENOMEM in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20210323123648.3997-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This LTE modem (M.2 card) has a bug in its power management:
there is some kind of race condition for U3 wake-up between the host and
the device. The modem firmware sometimes crashes/locks when both events
happen at the same time and the modem fully drops off the USB bus (and
sometimes re-enumerates, sometimes just gets stuck until the next
reboot).
Tested with the modem wired to the XHCI controller on an AMD 3015Ce
platform. Without the patch, the modem dropped of the USB bus 5 times in
3 days. With the quirk, it stayed connected for a week while the
'runtime_suspended_time' counter incremented as excepted.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210319124802.2315195-1-vpalatin@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not log the successful-probe message until the tty device has been
registered.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to always claim the data interface and bail out if binding
fails.
Note that the driver had a check to verify that the data interface was
not already bound to a driver but would not detect other failures (e.g.
if the interface was not authorised).
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
