Now that the irq vector code is in place, we can add the conditional
multiqueue TX code in the driver. This requires the optional
CONFIG_NETDEVICES_MULTIQUEUE=y and will not be enabled without
it.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Waskiewicz Jr, Peter P <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This code abstracts the per-queue MSI-X interrupt vector into
a queue vector layer. This abstraction is needed since there can
be many more queues than available MSI-X vectors in a machine.
The MSI-X irq vectors are remapped to a shared queue vector which
can point to several (both RX and TX) hardware queues. The NAPI
algorithm then cleans the appropriate ring/queues on interrupt
or poll.
The remapping is a delicate and complex calculation to make sure
that we're not unbalancing the irq load, and spreads the irqs
as much as possible, and may combine RX and TX flows onto the
same queue vector.
This effectively enables receive flow hashing across vectors
and helps irq load balance across CPUs.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Waskiewicz Jr, Peter P <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replaced init_module and cleanup_module with static functions and module_init/module_exit.
Signed-off-by: Jon Schindler <jkschind@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replaced init_module and cleanup_module with static functions and module_init/module_exit.
Signed-off-by: Jon Schindler <jkschind@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replaced init_module and cleanup_module with static functions and module_init/module_exit.
Signed-off-by: Jon Schindler <jkschind@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replaced init_module and cleanup_module with static functions and module_init/module_exit.
Signed-off-by: Jon Schindler <jkschind@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replaced init_module and cleanup_module with static functions and module_init/module_exit.
Signed-off-by: Jon Schindler <jkschind@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removes superh board specific configuration from the header file. These boards
will instead be configured using platform data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes sure SMC_insw()/SMC_outsw() are defined for the
default configuration. Without this change BUG()s will be triggered
when using 16-bit only platform data and the default configuration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch introduces struct smc91x_platdata and modifies the driver so
bus width is checked during run time using SMC_nBIT() instead of
SMC_CAN_USE_nBIT.
V2 keeps static configuration lean using SMC_DYNAMIC_BUS_CONFIG.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Pass a private data pointer to macros and functions. This makes it easy
to later on make run time decisions. This patch does not change any logic.
These changes should be optimized away during compilation.
V2 changes the macro argument name from "priv" to "lp".
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Resubmit #3
- Added s2io_vlan_rx_kill_vid entry point function for unregistering vlan.
- Fix to aggregate vlan packets. IP offset is incremented by
4 bytes if the packet contains vlan header.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Resubmit #2
- Transmit fifo selection based on TCP/UDP ports.
- Added tx_steering_type loadable parameter for transmit fifo selection.
0x0 NO_STEERING: Default FIFO is selected.
0x1 TX_PRIORITY_STEERING: FIFO is selected based on skb->priority.
0x2 TX_DEFAULT_STEERING: FIFO is selected based on L4 Ports.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Resubmit #3
Multiqueue netwrok device support implementation.
- Added a loadable parameter "multiq" to enable/disable multiqueue support,
by default it is disabled.
- skb->queue_mapping is not used for queue/fifo selection. FIFO selection is
based on skb->priority.
- Added per FIFO flags FIFO_QUEUE_START and FIFO_QUEUE_STOP. Check this flag
for starting and stopping netif queue and update the flags accordingly.
- In tx_intr_handler added a check to ensure that we have free TXDs before wak-
ing up the queue.
- Added helper functions for queue manipulation(start/stop/wakeup) to invoke
appropriate netif_ functions.
- Calling netif_start/stop for link up/down case respectively.
- As per Andi kleen's review comments, using skb->priority field for FIFO
selection.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
List of major changes and improvements:
no manipulation of the global ARP constructor
clean code split into core, layer 2 and layer 3 functionality
better exploitation of the ethtool interface
better representation of the various hardware capabilities
fix packet socket support (tcpdump), no fake_ll required
osasnmpd notification via udev events
coding style and beautification
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ctc driver is replaced by a new ctcm driver.
The ctcm driver supports the channel-to-channel connections of the
old ctc driver plus an additional MPC protocol to provide SNA
connectivity.
This patch removes the functions of the old ctc driver.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ctcm driver supports the channel-to-channel connections of the
old ctc driver plus an additional MPC protocol to provide SNA
connectivity.
This new ctcm driver replaces the existing ctc driver.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
adapt drivers/s390/net/Kconfig to current IBM wording
and further cosmetics
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rearrange functions to allow removal of some forward declarations.
Make certain global functions static along the way.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make needlessly global functions static. In a couple of cases this
requires removing forward declarations and reordering functions.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add some debug printks if we encounter a potentially bad receive
return descriptor.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use netif_msg_* for console messages emitted by the driver. Add a
parameter to allow control of messaging at driver startup, and also
add the ability to control it with ethtool.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use skb->csum_start for tx checksum offload preparation. Also swap
the variables css and cso so they hold the intended values of csum
start and offset, respectively.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit packet descriptor consists of four 32-bit words, with word 3
upper bits overloaded depending upon the condition of its bits 3 and 4.
The driver currently duplicates all word 2 and some word 3 register bit
definitions unnecessarily and also uses a set of nested structures in its
definition of the TPD without good cause. This patch adds a lengthy
comment describing the TPD, eliminates duplicate TPD bit definitions,
and simplifies the TPD structure itself. It also expands the TSO check
to correctly handle custom checksum versus TSO processing using the revised
TPD definitions. Finally, shorten some variable names in the transmit
processing path to reduce line lengths, rename some variables to better
describe their purpose (e.g., nseg versus m), and add a comment or two
to better describe what the code is doing.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the ethtool register dump option to the atl1 driver.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The L1 tx packet descriptor expects TCP Header Length to be expressed as a
number of 32-bit dwords. The atl1 driver uses tcp_hdrlen() to populate the
field, but tcp_hdrlen() returns the header length in bytes, not in dwords.
Add a shift to convert tcp_hdrlen() to dwords when we write it to the tpd.
Also, some of our bit assignments are made to the wrong tpd words. Change
those to the correct words.
Finally, since all this fixes TSO, enable TSO by default.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The future atl2 driver and the existing atl1 driver can share certain
functions and definitions. Move these shareable functions and definitions
out of atl1-specific files and into atlx.c and atlx.h. Some transitory
hackery will be present until atl2 is merged.
Reduce the number of source files by moving ethtool, hw, and param
functions from separate files into atl1_main.c, then rename it to just
atl1.c.
Move all atl1-specific definitions from atl1_hw.h to atl1.h.
Finally, clean up to make checkpatch.pl happy.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In preparation for a future Atheros L2 NIC driver (called atl2), relocate
the atl1 driver into a new /drivers/net/atlx directory that will ultimately
be shared with the future atl2 driver.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The xircom_tulip_cb driver has been replaced the xircom_cb driver, and
since it depended on BROKEN_ON_SMP it e.g. was no longer present in many
distribution kernels.
This patch therefore removes it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All the hardware supported by this driver is now supported
by the skge driver. The last remaining issue was support for ancient
dual port SysKonnect fiber boards, and the skge driver now does these
correctly (p.s. sk98lin was always broken on these old dual port
boards anyway).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- move boot_args[] into the init section
- move $global$ into the read_mostly section
- fix the following two section mismatches:
WARNING: vmlinux.o(.text+0x9c): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
WARNING: vmlinux.o(.text+0xa0): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
Signed-off-by: Helge Deller <deller@gmx.de>
SIgned-off-by: Kyle McMartin <kyle@mcmartin.ca>
Commit a0c1e9073e added code to futex.c
to detect whether futex_atomic_cmpxchg_inatomic was implemented at run
time:
+ curval = cmpxchg_futex_value_locked(NULL, 0, 0);
+ if (curval == -EFAULT)
+ futex_cmpxchg_enabled = 1;
This is bogus on parisc, since page zero in kernel virtual space is the
gateway page for syscall entry, and should not be read from the kernel.
(That, and we really don't like the kernel faulting on its own address
space...)
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
When we show_regs, we obviously have a struct pt_regs of the calling
frame. Use these in show_stack so we don't have the entire bogus call trace
up to the show_stack call.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This patch adds the known pa8900 CPUs to the inventory list and removes
the Crestone Peak one which apparently never escaped into the wild.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This patch moves the default parisc defconfig to
arch/parisc/configs/generic_defconfig where it belongs and selects it as
the default defconfig through KBUILD_DEFCONFIG.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Commit 721fdf3416 introduced a subtle bug
by accidently removing the "static" from iodc_dbuf. This resulted in, what
appeared to be, a trap without *current set to a task. Probably the result of
a trap in real mode while calling firmware.
Also do other misc clean ups. Since the only input from firmware is non
blocking, share iodc_dbuf between input and output, and spinlock the
only callers.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Originally, show_stack was used in BUG() output. However, a recent commit
changed it to print register state (no idea what that's supposed to help,
really...) and parisc was missing a backtrace because of it.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>