* pci/host-dra7xx:
PCI: dra7xx: Remove unneeded use of IS_ERR_VALUE()
* pci/host-imx6:
PCI: imx6: Simplify a trivial if-return sequence
* pci/host-spear:
PCI: spear: Use BUG_ON() instead of condition followed by BUG()
Simplify a trivial if-return sequence by combining it with a preceding
function call.
The semantic patch that makes this change is available in
scripts/coccinelle/misc/simple_return.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lucas Stach <l.stach@pengutronix.de>
Use BUG_ON() instead of an if condition followed by BUG().
The semantic patch that makes this change is available in
scripts/coccinelle/misc/bugon.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
There is no need to use the IS_ERR_VALUE() macro for checking the return
value from pm_runtime_* functions.
Test for a negative pm_runtime_get_sync() return value instead of using
IS_ERR_VALUE().
The semantic patch that makes this change is available in
scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
* pci/host-dra7xx:
ARM: dts: am57xx-evm: Add 'gpios' property with gpio2_8
PCI: dra7xx: Add support to make GPIO drive PERST# line
PCI: dra7xx: Clear MSE bit during suspend so clocks will idle
PCI: dra7xx: Add PM support
PCI: dra7xx: Disable pm_runtime on get_sync failure
* pci/host-iproc:
PCI: iproc: Allow BCMA bus driver to be built as module
PCI: iproc: Add arm64 support
PCI: iproc: Delete unnecessary checks before phy calls
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
Remove pci_ats_enabled(). There are no callers outside the ATS code
itself. We don't need to check ats_cap, because if we don't find an ATS
capability, we'll never set ats_enabled.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Stop caching the Invalidate Queue Depth in struct pci_dev.
pci_ats_queue_depth() is typically called only once per device, and it
returns a fixed value per-device, so callers who need the value frequently
can cache it themselves.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Move ATS declarations to linux/pci.h so they're all in one place.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
There's no need to BUG() if we enable ATS when it's already enabled. We
don't need to BUG() when disabling ATS on a device that doesn't support ATS
or if it's already disabled. If ATS is enabled, certainly we found an ATS
capability in the past, so it should still be there now.
Clean up these error paths.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Use the pci_physfn() helper rather than looking up physfn by hand.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The ATS setup code in ats_alloc_one() is only used by pci_ats_init(), so
inline it there. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
We previously returned -ENODEV for devices that don't support ATS (except
that we always returned 0 for VFs, whether or not they support ATS).
For consistency, always return -EINVAL (not -ENODEV) if the device doesn't
support ATS. Return zero for VFs that support ATS.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The extended capabilities list is linked with 12-bit pointers, and the ATS
Smallest Translation Unit and Invalidate Queue Depth fields are both 5
bits.
Use u16 and u8 to hold the extended capability address and the stu and qdep
values. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The pci_ats struct is small and will get smaller, so I don't think it's
worth allocating it separately from the pci_dev struct.
Embed the ATS fields directly into struct pci_dev.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Previously, we allocated pci_ats structures when an IOMMU driver called
pci_enable_ats(). An SR-IOV VF shares the STU setting with its PF, so when
enabling ATS on the VF, we allocated a pci_ats struct for the PF if it
didn't already have one. We held the sriov->lock to serialize threads
concurrently enabling ATS on several VFS so only one would allocate the PF
pci_ats.
Gregor reported a deadlock here:
pci_enable_sriov
sriov_enable
virtfn_add
mutex_lock(dev->sriov->lock) # acquire sriov->lock
pci_device_add
device_add
BUS_NOTIFY_ADD_DEVICE notifier chain
iommu_bus_notifier
amd_iommu_add_device # iommu_ops.add_device
init_iommu_group
iommu_group_get_for_dev
iommu_group_add_device
__iommu_attach_device
amd_iommu_attach_device # iommu_ops.attach_device
attach_device
pci_enable_ats
mutex_lock(dev->sriov->lock) # deadlock
There's no reason to delay allocating the pci_ats struct, and if we
allocate it for each device at enumeration-time, there's no need for
locking in pci_enable_ats().
Allocate pci_ats struct during enumeration, when we initialize other
capabilities.
Note that this implementation requires ATS to be enabled on the PF first,
before on any of the VFs because the PF controls the STU for all the VFs.
Link: http://permalink.gmane.org/gmane.linux.kernel.iommu/9433
Reported-by: Gregor Dick <gdick@solarflare.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
gpio2_8 is connected to the PCIe_RESETn line and it has to be driven low to
reset the PCIe cards. Add gpios property to PCIe DT node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The PERST# line in am57x-evm is connected to a GPIO line and PERST# should
be driven high to indicate the clocks are stable (As per Figure 2-10: Power
Up of the PCIe CEM spec 3.0).
Add support to make GPIO drive PERST# line.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DRA7xx requires the MSE bit to be cleared to set the master in standby
mode. (In DRA7xx TRM_vE, section 24.9.4.5.2.2.1 PCIe Controller Master
Standby Behavior advises to use the clearing of the local MSE bit to set
the master in standby. Without this some of the clocks do not idle).
Clear the MSE bit on suspend and enable it on resume. Clearing MSE bit is
required to get clocks to be idled after suspend.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Add PM support to pci-dra7xx so PCI clocks can be disabled during suspend
and enabled during resume without affecting PCI functionality.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Fix the error handling when pm_runtime_get_sync() fails.
If pm_runtime_get_sync() fails, call pm_runtime_disable() so there are no
unbalanced pm_runtime_enable() calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Change CONFIG_PCIE_IPROC_BCMA to tristate to make it possible to build this
driver as a module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ray Jui <rjui@broadcom.com>
The Intel 100-series chipset now includes the integrated Ethernet as part
of a multifunction package. The Ethernet function does not include native
ACS support, but Intel confirms that the device is not capable of peer-to-
peer within the package. We can therefore quirk it to expose the
isolation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: John Ronciak <john.ronciak@gmail.com>
set_irq_flags is ARM-specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in .map()
functions, and we can simply remove the set_irq_flags calls. Some users
also modify IRQ_NOPROBE, and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
We queued interrupt events for the MRL being opened or closed, but the code
in interrupt_event_handler() that handles these events ignored them.
Stop enabling MRL interrupts and remove the ignored events.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The list of interrupt events (INT_BUTTON_IGNORE, INT_PRESENCE_ON, etc.) was
copied from other hotplug drivers, but pciehp doesn't use them all.
Remove the interrupt events that aren't used by pciehp.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's platform-dependent, but an MMIO read to a non-existent PCI device
generally returns data with all bits set. This happens when the host
bridge or Root Complex times out waiting for a response from the device and
fabricates return data to complete the CPU's read.
One example, reported in the bugzilla below, involved this hierarchy:
pci 0000:00:1c.0: PCI bridge to [bus 02-3a] Root Port
pci 0000:02:00.0: PCI bridge to [bus 03-0a] Upstream Port
pci 0000:03:03.0: PCI bridge to [bus 05-07] Downstream Port
pci 0000:05:00.0: PCI bridge to [bus 06-07] Thunderbolt Upstream Port
pci 0000:06:00.0: PCI bridge to [bus 07] Thunderbolt Downstream Port
pci 0000:07:00.0: BCM57762 NIC
Unplugging the Thunderbolt switch and the NIC below it resulted in this:
pciehp 0000:03:03.0: Surprise Removal
tg3 0000:07:00.0: tg3_abort_hw timed out, TX_MODE_ENABLE will not clear MAC_TX_MODE=ffffffff
pciehp 0000:06:00.0: unloading service driver pciehp
pciehp 0000:06:00.0: pcie_isr: intr_loc 11f
pciehp 0000:06:00.0: Switch interrupt received
pciehp 0000:06:00.0: Latch open on Slot
pciehp 0000:06:00.0: Attention button interrupt received
pciehp 0000:06:00.0: Button pressed on Slot
pciehp 0000:06:00.0: Presence/Notify input change
pciehp 0000:06:00.0: Card present on Slot
pciehp 0000:06:00.0: Power fault interrupt received
pciehp 0000:06:00.0: Data Link Layer State change
pciehp 0000:06:00.0: Link Up event
The pciehp driver correctly noticed that the Thunderbolt switch (05:00.0
and 06:00.0) and NIC (07:00.0) had been removed, and it called their driver
remove methods.
Since the NIC was already gone, tg3 received 0xffffffff when it tried to
read from the device. The resulting timeout is a tg3 issue and not of
interest here.
Similarly, since the 06:00.0 Thunderbolt switch was already gone,
pcie_isr() received 0xffff when it tried to read PCI_EXP_SLTSTA, and pciehp
thought that was valid status showing that many events had happened: the
latch had been opened, the attention button had been pressed, a card was
now present, and the link was now up. These are all wrong, of course, but
pciehp went on to try to power up and enumerate devices below the
non-existent bridge:
pciehp 0000:06:00.0: PCI slot - powering on due to button press
pciehp 0000:06:00.0: Surprise Insertion
pci 0000:07:00.0 id reading try 50 times with interval 20 ms to get ffffffff
[bhelgaas: changelog, also check in pcie_poll_cmd() & pcie_do_write_cmd()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99841
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/irq:
PCI/MSI: Free legacy IRQ when enabling MSI/MSI-X
PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed
PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()
PCI: Add pcibios_alloc_irq() and pcibios_free_irq()
* pci/misc:
PCI: Remove unused "pci_probe" flags
PCI: Add VPD function 0 quirk for Intel Ethernet devices
PCI: Add dev_flags bit to access VPD through function 0
PCI / ACPI: Fix pci_acpi_optimize_delay() comment
PCI: Remove a broken link in quirks.c
PCI: Remove useless redundant code
PCI: Simplify pci_find_(ext_)capability() return value checks
PCI: Move PCI_FIND_CAP_TTL to pci.h and use it in quirks
PCI: Add pcie_downstream_port() (true for Root and Switch Downstream Ports)
PCI: Fix pcie_port_device_resume() comment
PCI: Shift PCI_CLASS_NOT_DEFINED consistently with other classes
PCI: Revert aeb30016fe ("PCI: add Intel USB specific reset method")
PCI: Fix TI816X class code quirk
PCI: Fix generic NCR 53c810 class code quirk
PCI: Use PCI_CLASS_SERIAL_USB instead of bare number
PCI: Add quirk for Intersil/Techwell TW686[4589] AV capture cards
PCI: Remove Intel Cherrytrail D3 delays
* pci/resource:
PCI: Call pci_read_bridge_bases() from core instead of arch code
* pci/virtualization:
PCI: Restore ACS configuration as part of pci_restore_state()
* pci/host-designware:
PCI: designware: Don't complain missing *config* reg space if va_cfg0 is set
* pci/host-xgene:
PCI: xgene: Add support for a 64-bit prefetchable memory window
arm64: dts: Add APM X-Gene PCIe 64-bit prefetchable window
PCI: xgene: Drop owner assignment from platform_driver
* pci/host-xilinx:
PCI: xilinx: Check for MSI interrupt flag before handling as INTx
Previously, pci_setup_device() and similar functions searched the
pci_bus->slots list without any locking. It was possible for another
thread to update the list while we searched it.
Add pci_dev_assign_slot() to search the list while holding pci_slot_mutex.
[bhelgaas: changelog, fold in CONFIG_SYSFS fix]
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rajat Jain reported a deadlock when PCIe hot-add and AER recovery happen at
the same time:
thread 1:
pciehp_enable_slot
pciehp_configure_device
pci_bus_add_devices
pci_bus_add_device
device_attach
device_lock(dev) # acquire device lock
...
pciehp_probe
init_slot
pci_hp_register
pci_create_slot
down_write(pci_bus_sem) # deadlock here
thread 2:
aer_isr_one_error
aer_process_err_device
do_recovery
broadcast_error_message(..., report_error_detected)
pci_walk_bus(..., cb=report_error_detected, ...)
down_read(&pci_bus_sem) # acquire pci_bus_sem
report_error_detected(dev) # cb()
device_lock(dev) # deadlock here
Previously, the bus->devices and bus->slots list were protected by
pci_bus_sem. In pci_create_slot(), we held it for writing so we could
add to the bus->slots list.
Add a new local pci_slot_mutex to protect bus->slots. Hold pci_bus_sem for
reading while searching the bus->devices list.
[bhelgaas: changelog]
Link: http://lkml.kernel.org/r/CAA93t1qpPqbih+UB0McA_d_+2rVaNkXsinAUxYzK9+JXSS+L-g@mail.gmail.com
Reported-by: Rajat Jain <rajatja@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Once MSI/MSI-X is enabled by the device driver, a PCI device won't use
legacy IRQs again until MSI/MSI-X is disabled.
Call pcibios_free_irq() when enabling MSI/MSI-X and pcibios_alloc_irq()
when disabling MSI/MSI-X. This allows arch code to manage resources
associated with the legacy IRQ.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Add pci_has_managed_irq(), pci_set_managed_irq(), and
pci_reset_managed_irq() to simplify code. No functional change.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
To support IOAPIC hotplug, we need to allocate PCI IRQ resources on demand
and free them when not used anymore.
Implement pcibios_alloc_irq() and pcibios_free_irq() to dynamically
allocate and free PCI IRQs.
Remove mp_should_keep_irq(), which is no longer used.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Add pcibios_alloc_irq() and pcibios_free_irq(), which are called when
binding/unbinding PCI device drivers.
PCI arch code may implement these to manage IRQ resources for hotplugged
devices.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
The following flags are only used on x86, but they got copied to FR-V,
MN10300, and SuperH:
PCI_PROBE_BIOS
PCI_PROBE_CONF1
PCI_PROBE_CONF2
PCI_ASSIGN_ROMS
PCI_NO_CHECKS
PCI_BIOS_IRQ_SCAN
PCI_ASSIGN_ALL_BUSSES
FR-V and MN10300 do test for PCI_ASSIGN_ROMS, but they never set it, so
it's dead code.
Remove the unused flags above.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
Currently on Keystone SoCs, we always complain:
keystone-pcie 21021000.pcie: missing *config* reg space
Keystone uses an older version of DesignWare hardware that doesn't have
ATU support. So va_cfg0_base and va_cfg1_base are already set up in
ks_dw_pcie_host_init() before calling dw_pcie_host_init(), and they point
to the remote config space address va (both same for Keystone). Add a
check to avoid this boot noise on Keystone.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add arm64 support to the iProc PCIe driver.
Note that on arm32, bus->sysdata points to the arm32-specific pci_sys_data
struct, and pci_sys_data.private_data contains the iproc_pcie pointer.
For arm64, there's nothing corresponding to pci_sys_data, so we keep the
iproc_pcie pointer directly in bus->sysdata.
In addition, arm64 does IRQ mapping in pcibios_add_device(), so it doesn't
need pci_fixup_irqs() as arm32 does.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.
[bhelgaas: changelog]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
CC: stable@vger.kernel.org
Add a dev_flags bit, PCI_DEV_FLAGS_VPD_REF_F0, to access VPD through
function 0 to provide VPD access on other functions. This is for hardware
devices that provide copies of the same VPD capability registers in
multiple functions. Because the kernel expects that each function has its
own registers, both the locking and the state tracking are affected by VPD
accesses to different functions.
On such devices for example, if a VPD write is performed on function 0,
*any* later attempt to read VPD from any other function of that device will
hang. This has to do with how the kernel tracks the expected value of the
F bit per function.
Concurrent accesses to different functions of the same device can not only
hang but also corrupt both read and write VPD data.
When hangs occur, typically the error message:
vpd r/w failed. This is likely a firmware bug on this device.
will be seen.
Never set this bit on function 0 or there will be an infinite recursion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
CC: stable@vger.kernel.org
Add a large window (up to 64GB) for X-Gene PCIe nodes to support devices
that require huge BARs.
Each X-Gene PCIe node will now have two memory windows: a 32-bit
non-prefetchable window and a 64-bit prefetchable window.
[bhelgaas: changelog]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we did not restore ACS state after a PCIe reset. This meant
that we could not reassign interfaces after a system suspend because the
D0->D3 transition disabled ACS, and we didn't restore it when going back to
D0.
Restore ACS configuration in pci_restore_state().
[bhelgaas: changelog]
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Allen Kay <allen.m.kay@intel.com>
CC: Chris Wright <chris@sous-sol.org>
CC: Alex Williamson <alex.williamson@redhat.com>
Occasionally both MSI and INTx bits in the interrupt decode register are
set at once by the Xilinx AXI PCIe Bridge, so the MSI flag in the interrupt
message should be checked to ensure that the correct handler is used.
If this check is not in place and the interrupt message type is MSI, the
INTx handler will be used erroneously when both type bits are set. This
will also be followed by a second read of the message FIFO, which can
result in the function returning early and the interrupt decode register
not being cleared if the FIFO is now empty.
Signed-off-by: Russell Joyce <russell.joyce@york.ac.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We check the ATS state (enabled/disabled) and fetch the PCI ATS Invalidate
Queue Depth in performance-sensitive paths. It's easy to cache these,
which removes dependencies on PCI.
Remember the ATS enabled state. When enabling, read the queue depth once
and cache it in the device_domain_info struct. This is similar to what
amd_iommu.c does.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Move first slot status read into while to simplify code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now in pci_hotplug_core.c, we randomly name a struct hotplug_slot and a
struct pci_slot. It's easy to confuse them, so let us use "slot" for a
struct hotplug_slot and "pci_slot" for a struct pci_slot.
No functional change.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function takes ACPI handle, not the device itself. Fix the
comment
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
