This will give us the ability to set the pixel and HDMI state machine
clocks for the VC4 KMS driver, change the CPU frequency, and
potentially gate clocks in the future (once we also write a power
domain driver). It also gives the uart an explicit clock reference,
so that we don't need to change the physical addresses of the old
fixed clk_bcm2835.c clocks for Raspberry Pi 2 port.
Two clocks get their frequencies updated as a result of this. One is
uart's apb_pclk, which was previously accidentally grabbing the fixed
uart0_pclk due to the apb_pclk not having clk_register_clkdev()
called. The uart doesn't seem to do anything with apb_pclk other than
make sure it's on, so that appears safe (also, as far as I can see,
the apb clock is actually the same as the VPU clock). The other is
EMMC, which according to the docs was supposed to be in the 50-100Mhz
range, but it turns out the firmware needed to change to running it at
the 250Mhz core clock speed to avoid a bug in clock domain crossing.
Additionally, anything using BCM2835_CLOCK_VPU will now have a correct
clock rate if the user configures the boot-time core clock speed using
config.txt.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The MSI Primo81 is an A31s based tablet, with 1G RAM, 16G NAND,
768x1024 IPS LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
rear camera, 3500 mAh battery, gt911 touchscreen, mma8452 accelerometer
and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
(both volume buttons are also connected to the UBOOT_SEL pin). The
external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
OTG and 3.5mm headphone jack.
USB OTG is enabled in host only mode. AXP221 USB power supply and
GPIO support are required for full USB OTG support.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Karsten Merker <merker@debian.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some boards, such as tablets, have regulators providing power to parts
of the display pipeline, like signal converters and LCD panels.
Add labels to the simplefb device nodes so that we can reference them
in the board dts files to add regulator supply properties.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable on-chip audio codec on the Marsboard A10.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Add support for severals Armada-370-based Seagate NAS
- Fix Ready NAS device tree
- Modify SDHCI binding for A388-GP allowing using it on old and new
version of the board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlYhOjIACgkQCwYYjhRyO9VTWACeJDBHZ1+ojF5irnZzNe/9PKaF
zJQAnjBmJxI1auTY+SQHVkZN3w2HOhwU
=Dvfj
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.4 (part 2)
- Add support for severals Armada-370-based Seagate NAS
- Fix Ready NAS device tree
- Modify SDHCI binding for A388-GP allowing using it on old and new
version of the board
* tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: set SW polling as SDHCI card detection on A388-GP
arm: mvebu: reorder nodes under internal-regs by address in RN2120 .dts file
arm: mvebu: disable unused Armada RTC on ReadyNAS 102, 104 and 2120
ARM: mvebu: add DT support for Seagate Personal Cloud
ARM: mvebu: add DT support for Seagate NAS 2 and 4-Bay
Signed-off-by: Olof Johansson <olof@lixom.net>
The keyboard driver for GPIO buttons(gpio-keys) checks for one of the
two boolean properties to enable gpio buttons as wakeup source:
1. "wakeup-source" or
2. the legacy "gpio-key,wakeup"
However juno, ste-snowball and emev2-kzm9d dts file have a undetected
"wakeup" property to indictate the wakeup source.
This patch fixes it by making use of "wakeup-source" property.
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd screen,
microsd slot, headphones, mini hdmi, mini usb b and power barrel connectors.
It uses a rtl8188cus usb wifi chip and a RDA 5875Y bluetooth chip attached
to uart2. It has a bma250 accelerometer attached to i2c1 addr 0x18, this
only works when ldo3 is set to 2.8 volt, otherwise i2c1 gets stuck, so
for now we mark i2c1 as failed.
It has a pixcir,pixcir_tangoc compatible touchscreen attached to i2c2 addr
0x5c. This is not enabled in this dts, because this variant of the
pixcir_tangoc has separate wakeup and enable pins both of which need
to be driven low before the touchscreen will work. Before we can enable
this the pixcir driver and devicetree-bindings need to be extended to
support these pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cubieboard uses the internal codec to output sound to its mini-jack.
Enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CHIP v0.2 has a composite output on a mini-jack connector, the audio
part being provided by the on-SoC codec. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Enable the audio-codec on the Mele A1000 top-set box.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The cubieboard2 uses the internal codec to output sound to its mini-jack.
Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
This commit enables the on-chip audio codec present on the A20 SoC
for the Cubietruck.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A20 SoC includes the Allwinner audio codec, capable of both 24-bit
playback and capture. This commit adds a device node for it.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A13 and A10s also have the audio codec present. List it in the device
tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A10 SoC includes the Allwinner audio codec, capable of both 24-bit
playback and capture. This commit adds a device node for it.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A20 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). Add it to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A13 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). However, it has a
different divider configuration than the A10, hence the difference
compatible.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A10 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). Add it to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Fix wrong compatible for A385 DB AP preventing using suspend
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlYhNEwACgkQCwYYjhRyO9XX9gCgnabcvdHrfFqAD3IFICLCgkOM
U1AAnReiDUjcUhz6oTl6I2+e3PLHY7RO
=BkFw
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.3-2' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu fixes for 4.3 (part 2)" from Gregory CLEMENT:
Fix wrong compatible for A385 DB AP preventing using suspend
* tag 'mvebu-fixes-4.3-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: correct a385-db-ap compatible string
- Fix oops with LPAE and moew than 2GB of memory by enabling
ZONE_DMA for LPAE. Probably no need for stable on this one as we
only recently ran into this with the mainline kernel
- Fix imprecise external abort caused by bogus SRAM init. This affects
dm814x recently merged, so no need for stable on this one AFAIK
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWJnm9AAoJEBvUPslcq6VzJHMP/i8DVa6R3OwssmGS3Cp/XKPV
m1GCXReauql0oUfFR0baiVnBKL6x8jEHW91iQeV3b3cUz+8l3jL7Q4yc+voPyjHz
ud890cId4wP54PWtDo4lpzDKi3lQkGBI+zJVAyWLfNPt97xcTh1yXW2HdDQ2Hlf4
nyksDKI1CE42h22l5odB9i0yf7Y/XXl8CYl0ZggHV1XReKSZGveTf8+Qcd1uME2s
ovLoxEOHDsmxwERXxeSw7Vw4MwefCBdXhKZf1a6l++/pyD/HqWNpJqpS+VEX4yaw
9ZGT5wmTZQXzzAx60bfO9kokFaKzKiae1UYZusR1aoEKKvFwh8+7ziTTv5q8Do+s
PRaeczB0tJA9OniwZaZEHNyckMgLlReH3PH5mwYV9DNNnG4LWRDjsx8LWDZ7lcjL
HxvDjbB6Ir51jGCxa4GVH0NZy0NZ+UHFTMv6bgiEc3uO4PMu35syDXfLws4VJWXZ
jC4bR2ShUbrAaGQj8R4aYQFus2MzXu58eqwceDGqeuf9M+wn10IO0/OaAXg5oPhk
TfqB/6+yC8GjyWyRaKV7PrgJKsqcm4S9P2WCuZL+lU5GgnfSrFTb1+OBQl4BQFXD
89Mj/oYOoKQd3qQFmsk2ZKwRqT9kLixKvih0bvkos4saOJipW2aNpLBTwNpQEpRk
N9J0CUyn/p1tQEBVCJj5
=EP6s
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Fixes for omaps for v4.3-rc cycle" from Tony Lindgren:
- Fix oops with LPAE and moew than 2GB of memory by enabling
ZONE_DMA for LPAE. Probably no need for stable on this one as we
only recently ran into this with the mainline kernel
- Fix imprecise external abort caused by bogus SRAM init. This affects
dm814x recently merged, so no need for stable on this one AFAIK
* tag 'omap-for-v4.3/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix imprecise external abort caused by bogus SRAM init
ARM: OMAP2+: Fix oops with LPAE and more than 2GB of memory
Use the AM33XX pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the AM33xx pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the OMAP3 pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am437x-gp-evm, pixcir_i2c_ts can wakeup the system from low power
state via pinctrl and IO daisy chain using generic wakeirq framework.
With commit 3fffd12839 ("i2c: allow specifying separate wakeup
interrupt in device tree") i2c core allows optional wakeirq to be
specified via device tree. Add wakeup irq entry to enable pixcir_i2c_ts
to wake the system from low power state.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I see that people are still sending emails to my old address (that no
longer exists) since is the one mentioned in the IGEP DTS. Replace it
with my current email address to avoid this.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the current implementation of GPIO hogging and with
gpio-pcf857x is built as module, ethernet doesn't work on boot
and doesn't throw any error/warning to user. Ethernet becomes
operational when inserting gpio-pcf857x module, even this time
there is no error/warning logs to user that ethernet is
operational.
When using with NFS rootfs and gpio-pcf857x as module, board
doesn't boot as it doesn't get any ip address and doesn't throw
any error/warning. To over come this, now cpsw driver tries to
get mode-gpios. When gpio-pcf857x is built as module it will
throw error, so that user can decide either to built in
gpio-pcf857x to continue with nfs boot or choose alternate rootfs
filesystem like sd/ramdisk.
When using mmc/ramdisk as root fs, cpsw will probe defer and
re-probes again when gpio-pcf857x module is inserted and ethernet
becomes operational.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The indentation for properties in the SATA device tree node on Tegra124
deviates from the rest of the device tree file. Restore consistency and
get rid of a couple of gratuitous blank lines while at it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The OTG arrangement on the LinkSprite pcDuino v3 Nano is the same as the
pcDuino 1/2/3: the OTG port's 5V line is connected directly to the 5V
bus (it's not switchable), and the OTG port's ID pin is connected to PH4
on the A20.
Tested successfully in both host and device modes.
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The second macb is present on all the sama5d4 SoCs. Let's add a node
reflecting it in the device tree.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
MMC data lines may be left floating if nothing is currently driving the
data lines, which is the case when mmc is in idle state, thus consuming
a useless extra amount of power. Add pullup on mmc2 data signals in the
same way it was previously done for mmc0 and mmc1.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add regulator nodes of PMIC ACT8945A chip on the board.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix instances of "disable" instead of "disabled"
in the at91rm9200 dtsi.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The PMC is not only used to drive the clocks but also has some registers
related to other functions. One of those is for example the USB gadget
bias.
Using a syscon allows to properly separate those functions.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some omaps are producing imprecise external aborts because we are
wrongly trying to init SRAM for device tree based booting. Only
omap3 is still using the legacy SRAM code, so we need to make it
omap3 specific. Otherwise we can get errors like this on at least
dm814x:
Unhandled fault: imprecise external abort (0xc06) at 0xc08b156c
...
(omap_rev) from [<c08b12e0>] (omap_sram_init+0xf8/0x3e0)
(omap_sram_init) from [<c08aca0c>] (omap_sdrc_init+0x10/0xb0)
(omap_sdrc_init) from [<c08b581c>] (pdata_quirks_init+0x18/0x44)
(pdata_quirks_init) from [<c08b5478>] (omap_generic_init+0x10/0x1c)
(omap_generic_init) from [<c08a57e0>] (customize_machine+0x1c/0x40)
(customize_machine) from [<c00098a4>] (do_one_initcall+0x80/0x1dc)
(do_one_initcall) from [<c08a2ec4>] (kernel_init_freeable+0x218/0x2e8)
(kernel_init_freeable) from [<c063a554>] (kernel_init+0x8/0xec)
(kernel_init) from [<c000f890>] (ret_from_fork+0x14/0x24)
Let's fix the issue by making sure omap_sdrc_init only gets called for
omap3. To do that, we need to have compatible "ti,omap3" in the dts
files. And let's also use "ti,omap3630" instead of "ti,omap36xx" like
we're supposed to.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "snps,quirk-frame-length-adjustment" property to
USB3 node for erratum A009116. This property provides
value of GFLADJ_30MHZ for post silicon frame length
adjustment.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The property name should be "gpio", not "gpios". Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix a typo, replacing "pinctrl-name" by "pinctrl-names"
in the Phytec phyFLEX-i.MX6 Quad dtsi.
Also fix a typo in the board name
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct core clock of spdif is SPDIF_GCLK, which is added to
clock tree. So the dts also need to be updated.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable NAND access by adding pinmux and NAND flash controller node
to device tree. The NAND chips currently used on the Colibri VF61
requires 8-bit ECC per 512 byte page, hence specify 32-bit ECC
strength per 2k page size.
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the NAND flash controller (NFC) peripherial. The driver
supports the SLC NAND chips found on Freescale's Vybrid Tower System
Module. The Micron NAND chip on the module needs 4-bit ECC per 512
byte page. Use 24-bit ECC per 2k page, which is supported by the
driver.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Based on i.MX6 Quad with 4GB of DDR3.
http://boundarydevices.com/product/nitrogen6max/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the different touchscreens that can be connected using
the displays available for this board.
http://boundarydevices.com/product-category/displays/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the 7" LCD display available for Sabrelite:
http://boundarydevices.com/product/7-800x480-display/
Also add label to backlight_lcd and connect it to the panel.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the 7" LCD display available for Nitrogen6x:
http://boundarydevices.com/product/7-800x480-display/
Also add label to backlight_lcd and connect it to the panel.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree node for touchscreen support on Colibri VF50. The
touchscreen functionality on VF50 uses the ADC channels of Vybrid
and some GPIOs. Also add pinctrl nodes for proper pinmux.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree node to support iomuxc-lpsr controller, fsl,input-sel
phandle allows to get input select register base address which is
shared from main iomuxc controller.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The INA220 monitors both shunt drop and supply voltage.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds dma-coherent property for eTSEC nodes, so
coherent DMA operations are supported.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for USBOTG1 and USBOTG2.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add imx6ul touchscreen controller support.
TSC module need ADC2 module to measure the touchscreen
coordinate value. This patch put TSC and ADC2 together,
make ADC2 module only be used for TSC, can't be used as
a normal ADC.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DCP block present on MX6SL is compatible with the one on MX28,
so add the compatible string and also complete the interrupt entries.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch enables On Chip OTP support for i.MX23 and i.MX28 SoCs,
but keeps the old compatible string.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-sdb board has a eMMC5.0 on usdhc3. This eMMC support HS400.
This patch add usdhc3 support for HS400
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6UL can be powered off by programming SNVS.
When long press ON/OFF button(5 seconds),
PMIC_ON_REQ pin will be set to low and external
PMIC will be powered off.
And system can be powered on by long press ON/OFF
button again.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SRAM support for i.MX6UL, it has 128KB ocram
starting from 0x900000.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a pinmux setting for using mmc2 in regular 4 bit mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When the gpio interrupt bindings where changed to add a bank to the
specifier list, the r_pio nodes of A23/A31/A33 where not updated to
match and neither was the pio node of the A80, this fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With omap5-board-common.dtsi, we can now easily add support for various omap5
board variants. Let's add minimal support for isee igepv5.
So far I've tested that basic things work, such as serial, USB Ethernet, HDMI
and WLAN.
Note that like omap5-uevm, these boards seem to need to reserve 16MB for a
trap section as in commit 03178c66d2 ("ARM: dts: omap5-evm: Update
available memory to 2032 MB") and also noted in a u-boot commit at
http://marc.info/?l=u-boot&m=134376852603255 and also at
http://patchwork.ozlabs.org/patch/159881/.
Not sure why this is not needed for omap5-cm-t54.dts, maybe because of
different u-boot configuration.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like thevarious omap5-uevm models and igepv5 are very similar. So let's
create omap5-board-common.dtsi to allow fixing up things properly for mainline
kernel to support all these.
Even if we eventually end up having only PMIC + MMC + eMMC + SDIO WLAN + SATA +
USB + HDMI configuration in the omap5-board-common.dtsi, this is the easiest
way to add support for other boards rather than diffing various versions of
out of tree dts files.
My guess is that also omap5-sbc-t54.dts can use this, but I don't have that
board so that will need to be dealt with later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 99f84cae43 ("ARM: dts: add wl12xx/wl18xx bindings") added
device tree bindings for the TI WLAN SDIO on many omap variants.
I recall wondering how come omap5-uevm did not have the WLAN
added and this issue has been bugging me for a while now, and
I finally tracked it down to a bad pinmux regression, and a missing
deferred probe handling for the 32k clock from palmas that's
requested by twl6040.
Basically 392adaf796 ("ARM: dts: omap5-evm: Add mcspi data")
added pin muxing for mcspi4 that conflicts with the onboard
WLAN. While some omap5-uevm don't have WLAN populated, the
pins are not reused for other devices. And as the SDIO bus
should be probed, let's try to enable WLAN by default.
Let's fix the regression and add the WLAN configuration as
done for the other boards in 99f84cae43 ("ARM: dts: add
wl12xx/wl18xx bindings"). And let's use the new MMC pwrseq for
the 32k clock as suggested by Javier Martinez Canillas
<javier@dowhile0.org>.
Note that without a related deferred probe fix for twl6040,
the 32k clock is not initialized if palmas-clk is a module
and twl6040 is built-in.
Let's also use the generic "non-removable" instead of the
legacy "ti,non-removable" property while at it.
And finally, note that omap5 seems to require WAKEUP_EN for
the WLAN GPIO interrupt.
Fixes: 392adaf796 ("ARM: dts: omap5-evm: Add mcspi data")
Cc: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The newest revisions of A388-GP (v1.5 and higher) support only
DAT3-based card detection. Revisions < v1.5 based on GPIO detection
via I2C expander, but this solution is supposed to be deprecated on
new boards. In order to satisfy all type of hardware this commit
changes card detection to use software polling mechanism. Also a
comment is added on possible card detection options in A388-GP
DT board file.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The sorting policy for this file is alphabetically.
Reorder all nodes, that are out of place.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The NMI interrupt controller is in charge of the NMI pin exposed by
the SoC to the PMIC. The PMIC signals interrupts through this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add FPGA manager to device tree for SoCFPGA.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
* Implement id_table driver matching in SMD
* Avoid NULL pointer exception on remove of SMEM
* Reorder SMEM/SMD configs
* Make qcom_smem_get() return a pointer
* Handle big endian CPUs correctly in SMEM
* Represent SMD channel layout in structures
* Use __iowrite32_copy() in SMD
* Remove use of VLAIs in SMD
* Handle big endian CPUs correctly in SMD/RPM
* Handle big endian CPUs corretly in SMD
* Reject sending SMD packets that are too large
* Fix endianness issue in SCM __qcom_scm_is_call_available
* Add missing prototype for qcom_scm_is_available()
* Correct SMEM items for upper channels
* Use architecture level to build SCM correctly
* Delete unneeded of_node_put in SMD
* Correct active/slep state flagging in SMD/RPM
* Move RPM message ram out of SMEM DT node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hprv
-----END PGP SIGNATURE-----
Merge tag 'qcom-soc-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm into next/drivers
Pull "Qualcomm ARM Based SoC Updates for 4.4" from Andy Gross:
* Implement id_table driver matching in SMD
* Avoid NULL pointer exception on remove of SMEM
* Reorder SMEM/SMD configs
* Make qcom_smem_get() return a pointer
* Handle big endian CPUs correctly in SMEM
* Represent SMD channel layout in structures
* Use __iowrite32_copy() in SMD
* Remove use of VLAIs in SMD
* Handle big endian CPUs correctly in SMD/RPM
* Handle big endian CPUs corretly in SMD
* Reject sending SMD packets that are too large
* Fix endianness issue in SCM __qcom_scm_is_call_available
* Add missing prototype for qcom_scm_is_available()
* Correct SMEM items for upper channels
* Use architecture level to build SCM correctly
* Delete unneeded of_node_put in SMD
* Correct active/slep state flagging in SMD/RPM
* Move RPM message ram out of SMEM DT node
* tag 'qcom-soc-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm:
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
soc: qcom: smd_rpm: Handle big endian CPUs
soc: qcom: smd: Remove use of VLAIS
soc: qcom: smd: Use __iowrite32_copy() instead of open-coding it
soc: qcom: smd: Represent channel layout in structures
soc: qcom: smem: Handle big endian CPUs
soc: qcom: Make qcom_smem_get() return a pointer
soc: qcom: Reorder SMEM/SMD configs
soc: qcom: smem: Avoid NULL pointer exception on remove
soc: qcom: smd: Implement id_table driver matching
- DCAN sleep pins for am437x-gp-evm
- A series of changes to add audio support for dra7
- Add support for gpio keys and LEDs on dra7
- Regulator clean-up for am335x-wega
- A series of changes to enable IOMMUs and mailboxes for dra7
accelerators
- Add support for am335x-bonegreen
- Fix up GPIO flags where 0 was used instead of GPIO_ACTIVE_HIGH
- Fix omap3-lilly-am33x IRQ level flag
- Remove duplicate uart2 pinmux for igep and fix indentation and
update igep to use pinctrl macros for the register offsets
- Fix MMC cd-gpios usage
Note that this branch is against v4.3-rc4 as that contains critical
MMC related fixes to boot with MMC working on most omaps.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWHr4GAAoJEBvUPslcq6Vzhr8QAMAH0SNDea4C48F7vPkjA31V
D0x1hGnLkeXbInR9H+pDjULuLdY8bQubCi0gdpH0OAxUarga2WneTC9A0IaNs3gm
YR3fS3RnusrPdderNJ00fkJaz1taaQmEdbKAxgPG2XabOZtUDqRhE4JafUnMN2QI
jOde4CS3XDbzEfsDLxrxzsw8x1wHnPRQ4LWHVxuUYIPVRsbwbU+Ur23NPxUU7JtQ
g+Lf86PR5B3AtXqh+1x0cdpoybyCpKSqFnvFBEQS997B+7DQYKXwVWRZctBtSsV0
66BccG/dN3YSG+WdRno4R8ikrebuhhdVTn8bOUIFN83o5BjDAuWKBsYXYkVHsusk
wLRnFkLwkNoil8C4DWY9+RfdX7uLwcCPppBB4PF6P541rbPGpV8O19/D5v1qBCVQ
p4GxNarygJdXWEzYb22x9KEwVBHz8waPNfuRz82TrgcttTyDWUtiUbRnxRtI137a
V8g5/TrR8p1WwRFlp4X7UFhZACqn1CSoNW9J1eax7VpGm5I8DEECAOzSHUId98k5
eRhfC5r/tLWDl3IkSnKrGnQ2hVu6dcazFj3nMJacYkpmRghoHvp+7ElepxffZCae
+V8TXFP6ehEajkvrExPRL8Ey9UdMJEXeof5t/o2Vt0b2w+XeLOpuoDrKbcJsYPMb
RWisiAUU/KWk6UQYOPj5
=Sbup
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree changes for omaps for v4.4 merge window:" from Tony Lindgren:
- DCAN sleep pins for am437x-gp-evm
- A series of changes to add audio support for dra7
- Add support for gpio keys and LEDs on dra7
- Regulator clean-up for am335x-wega
- A series of changes to enable IOMMUs and mailboxes for dra7
accelerators
- Add support for am335x-bonegreen
- Fix up GPIO flags where 0 was used instead of GPIO_ACTIVE_HIGH
- Fix omap3-lilly-am33x IRQ level flag
- Remove duplicate uart2 pinmux for igep and fix indentation and
update igep to use pinctrl macros for the register offsets
- Fix MMC cd-gpios usage
Note that this branch is against v4.3-rc4 as that contains critical
MMC related fixes to boot with MMC working on most omaps.
* tag 'omap-for-v4.4/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (33 commits)
ARM: dts: omap3-igep: Use OMAP3_CORE1_IOPAD pinmux macro
ARM: dts: dra7xx: am57xx: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: am43xx: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: am335x: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: omap3-igep0020: Remove duplicate uart2 pinmux
ARM: dts: omap3-igep: Fix indentation
ARM: dts: omap3-lilly-a83x: Don't use IRQ level flag for a GPIO
ARM: dts: DRA74x: Add IOMMU nodes for DSP2
ARM: dts: DRA7: Add common IOMMU nodes
ARM: dts: DRA74x: Add dsp2_system syscon node
ARM: dts: DRA7: Add dsp1_system syscon node
ARM: dts: Use defined GPIO constants in flags cell for OMAP2+ boards
ARM: dts: Add am335x-bonegreen
ARM: dts: beagle-x15: Enable the system mailboxes 5 and 6
ARM: dts: dra72-evm: Enable the system mailboxes 5 and 6
ARM: dts: dra7-evm: Enable the system mailboxes 5 and 6
ARM: dts: DRA72x: Add IPC sub-mailbox nodes for IPU1, IPU2 & DSP1
ARM: dts: DRA74x: Add IPC sub-mailbox nodes for all IPUs & DSPs
ARM: dts: am335x-wega: Clean up regulators
ARM: dts: dra7-evm: add gpio key support
...
While the addition of these properties is technically correct it unveils
a bug with deferred probe. The problem is that the presence of the gpio-
range property causes the gpio-tegra driver to defer probe (it needs the
pinctrl driver to be ready). That's technically correct, but it causes a
couple of issues:
- The keyboard on Chromebooks stops working. The reason for that is
that the gpio-tegra device has not registered an IRQ domain by the
time the EC SPI device is registered, hence the interrupt number
resolves to 0. This is technically a bug in the SPI core, since it
should really resolve the interrupt at probe time and defer if the
IRQ domain isn't available yet. This is similar to what's done for
I2C and platform device already.
- The gpio-tegra device deferring probe means that it is moved to the
end of the dpm_list. This list defines the suspend/resume order for
devices. However the core lacks a way to move all users of the
gpio-tegra device to the end of the dpm_list at the same time. This
in turn results in a subtle bug on Jetson TK1, where the gpio-keys
device is used to expose the power key as input. The power key is a
convenient way to wake the system from suspend. Interestingly, the
gpio-keys device ends up getting probed at a point after gpio-tegra
has been probed successfully from having been deferred earlier. As
such the driver doesn't need to defer the probe itself, and hence
the device isn't moved to the end of the dpm_list. This causes the
gpio-tegra device to be suspended before gpio-keys, which in turn
leaves gpio-keys unable to wake the system from suspend.
There are patches in the works to fix both of the above issues, but they
are too involved to make it into v4.3, so in the meantime let's fix the
regressions by commenting out the gpio-ranges properties until the fixes
have landed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
