cycle
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw
spinlocks in IRQ handlers to play nice with the realtime
patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8,
PH1-Pro5, ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner
sun4i driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC
subdrivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4QFX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.3 development
cycle.
Like with GPIO it's a lot of stuff. If my subsystems are any sign of
the overall tempo of the kernel v4.3 will be a gigantic diff.
[ It looks like 4.3 is calmer than 4.2 in most other subsystems, but
we'll see - Linus ]
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data(). This series was
created by Thomas Gleixner after the problem was observed by
Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw spinlocks
in IRQ handlers to play nice with the realtime patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8, PH1-Pro5,
ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner sun4i
driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC subdrivers"
* tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (95 commits)
pinctrl: at91: fix null pointer dereference
pinctrl: mediatek: Implement wake handler and suspend resume
pinctrl: mediatek: Fix multiple registration issue.
pinctrl: sh-pfc: r8a7794: add USB pin groups
pinctrl: at91: Use generic irq_{request,release}_resources()
pinctrl: cherryview: Use raw_spinlock for locking
pinctrl: baytrail: Use raw_spinlock for locking
pinctrl: imx6ul: Remove .owner field
pinctrl: zynq: Fix typos in smc0_nand_grp and smc0_nor_grp
pinctrl: sh-pfc: Implement pinconf power-source param for voltage switching
clk: rockchip: add pclk_pd_pmu to the list of rk3288 critical clocks
pinctrl: sun4i: add spdif to pin description.
pinctrl: atlas7: clear ugly branch statements for pull and drivestrength
pinctrl: baytrail: Serialize all register access
pinctrl: baytrail: Drop FSF mailing address
pinctrl: rockchip: only enable gpio clock when it setting
pinctrl/mediatek: fix spelling mistake in dev_err error message
pinctrl: cherryview: Serialize all register access
pinctrl: UniPhier: PH1-Pro5: add I2C ch6 pin-mux setting
pinctrl: nomadik: reflect current input value
...
and the addition of new clock drivers. Stephen Boyd has also done a lot
of subsystem-wide driver clean-ups (thanks!). There are also fixes to
the framework core and changes to better split clock provider drivers
from clock consumer drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QAiQ
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The clk framework changes for 4.3 are mostly updates to existing
drivers and the addition of new clock drivers. Stephen Boyd has also
done a lot of subsystem-wide driver clean-ups (thanks!). There are
also fixes to the framework core and changes to better split clock
provider drivers from clock consumer drivers"
* tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: s5pv210: add missing call to samsung_clk_of_add_provider()
clk: pistachio: correct critical clock list
clk: pistachio: Fix PLL rate calculation in integer mode
clk: pistachio: Fix override of clk-pll settings from boot loader
clk: pistachio: Fix 32bit integer overflows
clk: tegra: Fix some static checker problems
clk: qcom: Fix MSM8916 prng clock enable bit
clk: Add missing header for 'bool' definition to clk-conf.h
drivers/clk: appropriate __init annotation for const data
clk: rockchip: register pll mux before pll itself
clk: add bindings for the Ux500 clocks
clk/ARM: move Ux500 PRCC bases to the device tree
clk: remove duplicated code with __clk_set_parent_after
clk: Convert __clk_get_name(hw->clk) to clk_hw_get_name(hw)
clk: Constify clk_hw argument to provider APIs
clk: Hi6220: add stub clock driver
dt-bindings: clk: Hi6220: Document stub clock driver
dt-bindings: arm: Hi6220: add doc for SRAM controller
clk: atlas7: fix pll missed divide NR in fraction mode
clk: atlas7: fix bit field and its root clk for coresight_tpiu
...
The base addresses for the Ux500 PRCC controllers are hardcoded,
let's move them to the clock node in the device tree and delete
the constants.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The "cpus" node cannot be inside the "soc" node, while this
works for the CoreSight blocks, the early boot code will look
for "cpus" directly under the root node, so this is a hard
convention. So move the CPU nodes.
Augment the "reg" property to match what is actually in the
hardware: 0x300 and 0x301 respectively.
Then add an SMP enablement type to be used by the SMP init
code, "ste,dbx500-smp".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This gets the GPIO ranges out of the driver and into the device
tree where they belong. Standard DT bindings already exist for
this. Since no systems with this are deployed we can just augment
all device trees and the drivers at the same time and simplify
the world.
This also defines the array of GPIO chips related to the pin
controller.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enumerates the PL011 serial ports on the Ux500. This is
necessary to do if we want to remove one of the serial ports,
since userspace depends on console to be present on ttyAMA2
and we must not break userspace.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Ux500 SOCs have a special backup RAM that needs to be
defined in the device tree.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Ux500 like other Cortex-A9 SoC's has a Snoop Control
Unit (SCU) and a Watchdog in the same address range as
the local timers. Add these to the SoC device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Define CPU topology, connect that with CoreSight blocks,
add sensor information to DT boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+QE+
-----END PGP SIGNATURE-----
Merge tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Ux500 Device Tree changes for the v4.2 series" form Linus Walleij:
Define CPU topology, connect that with CoreSight blocks,
add sensor information to DT boards.
* tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: add the sensors to the STUIB board
ARM: ux500: assign the sensor trigger IRQs
ARM: ux500: fix lsm303dlh magnetometer compat string
ARM: ux500: add CoreSight blocks to DTS file
ARM: ux500: define CPU topology
This registers all the CoreSight blocks on the DB8500 SoC:
each core has a PTM (v1.0, r1p0-00rel0) connected, both connected
to a funnel (DK-TM908-r0p1-00rel0) which in turn connects to a
replicator (DM-TM909-r0p1-00rel0). The replicator has two outputs,
port 0 to a TPIU interface and port 1 to an ETB
(DK-TM907-r0p3-00rel0). The CoreSight blocks are all clocked by
the APEATCLK from the PRCMU and their AHB interconnect is clocked
from a separate clock called APETRACECLK.
The SoC also has a CTI/CTM block which can be added later as we
have upstream support in the CoreSight subsystem.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CPU topology is unspecified for Ux500 but will be needed
for things like CoreSight. Let's just add it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO regulator for the SD-card isn't a ux500 SOC configuration, but
instead it's specific to the board. Move the definition of it, into the
board DTSs.
Fixes: c94a4ab7af ("ARM: ux500: Disable the MMCI gpio-regulator by default")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The i2c-nomadik driver handle these devices properly from a runtime PM
perspective. Therefore, let's add them into VAPE PM domain for ux500.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The spi-pl022 driver handle these devices properly from a runtime PM
perspective. Therefore, let's add them into VAPE PM domain for ux500.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mmci driver handle these devices properly from a runtime PM
perspective, including register context save/restore. Therefore let's
add them into VAPE PM domain for ux500.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a DT node for the ux500 PM domains. Follow the DT semantics of the
generic PM domain.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds some missing DMA channel information to the disabled
MMC/SD/SDIO blocks number 3 and 5, and notes that the assignment
of MSP channels vary with ASIC variant.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As noted in recent discussions the name of the core clock for
the PL022 derived SPI blocks is erroneously named in the
Ux500 device trees. The kernel doesn't currently use the name,
but may do so soon so let use rename all these clocks in
accordance with the name given in the PL022 TRM (ARM DDI 0194G).
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we need to connect resources such as pin mappings and clocks
when deleting board files, we create a MCDE node even though there
is no driver for it. As it is only using standard bindings right
now, this does not matter much. When a proper driver is written
for the MCDE, it can augment this node with custom properties.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the SSP and SPI blocks to the device tree and makes
them active. Only this way can their clocks be properly gated
off at boot.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCLK for I2C4 is controlled by bit 10 in the PCKEN registers
while the KCLK is controlled by bit 9 on the KCKEN, it's
one of these odd assymetric things. Correct the PCLK bit to 10.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock assignment in the device tree for GPIO blocks 6
and 7 was incorrect, indicating this was managed by bit 1 on
PRCC 2 while it was in fact bit 11 on PRCC 2.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock assignment in the device tree for GPIO block 8 was
incorrect, indicating this was managed by bit 1 on PRCC 6
while it was in fact bit 1 on PRCC 5.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is required to fetch the ARMSS clock when booting with DT.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The common clock framework will use the 'clock' property provided to do
a clock lookup when Device Tree is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The common clock framework will use the 'clock' property provided to do
a clock lookup when Device Tree is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MTU0 is required for full booting of the system. The driver has
been previously DT:ed and is in use on the Nomadik platform, but we
also need to enable it on ux500 based systems.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The "mentor,musb" binding isn't documented so I was about
to document it.
The node is missing a few properties for configuration like
"multipoint", "dyn_fifo", "num_eps" or "ram_bits". However
I am not sure "missing" is the right word here because some
of those informations might be obtained from the chip itself
but it is not done (yet).
Further the ePARP 2.3.1 says the matching goes from left to
right taking the fist match. Right now there is jus a driver
for "stericsson,db8500-musb" and none for "mentor,musb".
I'm not 100% that it is simply possible to have a generic
since even for DMA we have ifdefs in the driver between
"generic mentor dma" and "ux500 dma" and I mean within musb
and not the dma code.
For that reason (that I am not sure a generic musb binding
is possible and how its binding / required properties will
look like) and the reason that we have here a minor binding
without a driver to look at I suggest to remove that binding.
If the majority of people prefer to keep this binding I'm
curious how the documentation of the binding should look like.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Turns out that they're actually not required and the driver probes just
fine without them. The ID is incorrect at the moment anyway. They actually
currently specify the stn8815.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
