After waking up from full sleep, registers are accessible, but rx/tx
typically fails. A fast channel change will not recover from this, so
ensure that a full-sleep -> wake transition is always followed by a full
reset.
The reason why this hasn't created any serious problems yet is that it's
hidden by the (wrong) behavior of enabling/disabling the radio when the
wiphy idle state changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fixes a regression on single-stream chips introduced in
commit 43c3528430
"ath9k: implement .get_antenna and .set_antenna"
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add interface address so it can be mapped to a local
interface. Add max-ampdu and mpdu-density.
Print out the tid->baw_size
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export how many times each of the reset triggers has fired through debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.
The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
ops.conf_tx = conf_tx_op;
@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
conf_tx_op (
- struct ieee80211_hw *hw,
+ struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u16 queue,
const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For uAPSD implementation, it is necessary to know on
which ACs frames are buffered. mac80211 obviously
knows about the frames it has buffered itself, but
with aggregation many drivers buffer frames. Thus,
mac80211 needs to be informed about this.
For now, since we don't have APSD in any form, this
will unconditionally set the TIM bit for the station
but later with uAPSD only some ACs might cause the
TIM bit to be set.
ath9k is the only driver using this API and I only
modify it in the most basic way, it won't be able
to implement uAPSD with this yet. But it can't do
that anyway since there's no way to selectively
release frames to the peer yet.
Since drivers will buffer frames per TID, let them
inform mac80211 on a per TID basis, mac80211 will
then sort out the AC mapping itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After 'ath9k: optimize ath9k_ps_restore', it would only send the device to
network sleep and not to full sleep anymore, potentially causing more
battery drain.
Reported-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.
Update all the drivers that implement these callbacks.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so, the caldata continues to retain older history
values learned on that channel. It is always safer to start
noise floor calibration from the defaults after the assoication.
So this patch resets the nf history buffer when none of the
STA vifs are associated.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_hw_cycle_counters_update only needs to be called if the power state
changes. Most of the time this does not happen, even when ps_usecount
goes down to 0.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During a reset, rx buffers are flushed after rx has been disabled. To avoid
race conditions, rx needs to stay disabled during the reset, so avoid any
calls to ath9k_hw_rxena in that case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt handler increases the interrupt disable refcount, so the
tasklet needs to always call ath9k_hw_enable_interrupts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On MIMO chips this can be used to enable/disable hardware chains, ensuring
that the MCS information is updated accordingly.
On non-MIMO chips with rx diversity (e.g. 9285), this configures the rx
input antenna.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
reduces unnecessary code duplication. Also takes the sc_pcu_lock within
ath_reset instead of callsites, which makes it possible to always cancel
all queued work items before the reset, possibly fixing a few race
conditions (work items vs reset) along with it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it much easier to add further rework to avoid race conditions
between reset and other work items.
Move other functions to make ath_reset static.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helps with making ath_reset static in the next commit
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we already have ah->{rx,tx}chainmask for the same purpose
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch keep track of number of samples that includes
DMA debugs registers, PCU observe, CR, channel noise,
cycle conters, noisefloor history buffer and last N number
of tx and rx descriptor status. These samples are grouped
in table manner which dumping in debgufs.
Debugfs file location:
<debugfs_mnt>/ieee80211/phy#/ath9k/samples
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this useful for debugging and to keep track of success/failure of
frames such as ACK, RTS and FCS error count in a noisy environment
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While switching b/w HT20/40, the current channel's nf values
are updated into history buffer. Since the current channel's
channel type, channel flag got updated before reading
nf value from hw. This channel type mismatch is causing invalid
readings when hw is on ht20 but getnf tries to read on extn chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever RXEOL is received, both RXORN and RXEOL got cleared
to avoid rx overrun interrupt storm. This was handled only for
edma chips. The same scenario was also observered with AR9280,
doing frequent channel type switch b/w HT20/40 with bidi traffic
that is causing failure to stop rx dma. This patch clears
the RXEOL & RXORN interrupts for all chips.
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020
DMADBG_7=0x000062c0
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:532
ath_stoprecv+0x110/0x120 [ath9k]()
Call Trace:
[<ffffffff8104a55a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104a5a5>] warn_slowpath_null+0x15/0x20
[<ffffffffa0560380>] ath_stoprecv+0x110/0x120 [ath9k]
[<ffffffffa055e6fa>] ath_reset+0x6a/0x200 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this callback is called during suspend/resume and also via iw command.
it configures parameters like sifs, slottime, acktimeout in
ath9k_hw_init_global_settings where few REG_READ, REG_RMW are also done
and hence the need for PS wrappers
Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable ASPM in pci ->probe on upstream (device) and downstream
(PCIe port) component. According to e1000e driver authors this is
required. I did not find that requirement in PCIe spec, but it seems
to be logical for me.
This need to be fixed for CONFIG_PCIEASPM, that will be done later ...
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We always call ->config_pci_powersave() with both restore and power_off
arguments equal to 0 or both equal to 1, so merge them into one
argument.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The received tx status of aggregated frame without BlockAck may
cause deaf state in AR5416 cards. So the driver does a reset to
recover. When this happens, we release the pcu_lock before doing
a reset as ath_rest acquires pcu_lock. This is ugly and also not
atomic. Fixing this addresses the TX DMA failure also.
ath_tx_complete_aggr can be called from different paths which
takes different variants of spin_lock. This patch also addresses
the following warning.
WARNING: at kernel/timer.c:1011 del_timer_sync+0x4e/0x50()
Call Trace:
<IRQ> [<ffffffff8104be3a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104be85>] warn_slowpath_null+0x15/0x20
[<ffffffff8105915e>] del_timer_sync+0x4e/0x50
[<ffffffffa03726be>] ath_reset+0x3e/0x210 [ath9k]
[<ffffffff8135cdaf>] ? _raw_spin_unlock_bh+0x1f/0x30
[<ffffffffa037760a>] ath_tx_complete_aggr.isra.26+0x54a/0xa40 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
during suspend/resume ath9k_stop will always call ath_radio_disable
which will inturn call ath9k_hw_configpcipowersave, so no need to call
it explicitly in ath9k_stop
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add few debug messages for some of the possible scenarios
where we can detect PAPRD failures. this will help us to be
sure that we had really enabled PAPRD
Cc: susinder@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this helps the user to start/stop ANI dynamically.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In PAPRD table initialization path we do some register read, so
make sure the chip is awake during that. Currently PAPRD is disabled.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure ibss node's bss_changes under BSS_CHANGED_IBSS.
And also start/stop ani timer only if the station join/leave
the group.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EDMA based chips (AR9380+) have 8 Tx FIFO slots, which are used to fix the
tx queue start/stop race conditions which have to be worked around for
earlier chips by keeping the last descriptor in the queue. The current code
stores all frames that do not fit onto the 8 FIFO slots in a separate
list. Whenever a FIFO slot is freed up, the next frame (or A-MPDU) from the
pending queue gets moved to that slot.
This process is not only inefficient, but also unnecessary. The code can
be improved visibly by keeping the pending queue fully linked, and moving
the contents of the entire queue to a FIFO slot as it becomes available.
This patch makes the necessary changes for that and also merges some code
that was duplicated for EDMA vs non-EDMA. It changes txq->axq_link to point
to the last descriptor instead of the link pointer, so that
ath9k_hw_set_desc_link can be used, which works on all chips.
With this patch, a small performance increase for non-aggregated traffic
was observed on AR9380 based embedded hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resetting hardware helps to recover from baseband
hang/panic for AR9003 based chips.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we are not doing anything by tracking the number of pending frames.
bail out when we first find a pending frame in any one of the 10 queues.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only leave filtering enabled for AP or VLAN interfaces, clear the
destination mask for all other interfaces.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh beaconing on ath9k was broken by this commit:
commit 4801416c76
Author: Ben Greear <greearb@candelatech.com>
Date: Sat Jan 15 19:13:48 2011 +0000
This patch assigns the right opmode when the device is used in mesh
mode.
Reported-by: Fabrice Deyber fabricedeyber@agilemesh.com
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This beacon rssi will be used to set noisefloor during ani reset.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Processing TSF out of range before RX helps to update beacon
timers so early in the succeeding rx process.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assumsion is that while processing ath9k tasklet,
interrupts were already disabled and it will be enabled
at the completion of ath9k tasklet. But whenever TSFOOR is raised,
the driver configures the beacon timers after having received a
beacon frame from the AP which inturn enables the interrupts.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
during suspend/S3 state drv_flush is called from mac80211 irrespective of
interface count. In ath9k we queue a work in ath9k_flush which we expect
to be cancelled in the drv_stop call back. during suspend process mac80211
calls drv_stop only when the interface count(local->count) is non-zero.
unfortunately when the network manager is enabled, drv_flush is called
while drv_stop is not called as local->count reaches '0'.
So fix this by simply checking for the device presence in the
drv_flush call back in the driver before queueing work or anything else.
this patch fixes the following WARNING
Call Trace:
[<c014c6e2>] warn_slowpath_common+0x72/0xa0
[<fc133f99>] ? ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<fc133f99>] ? ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<c014c75b>] warn_slowpath_fmt+0x2b/0x30
[<fc133f99>] ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<fc134ed1>] ieee80211_queue_delayed_work+0x21/0x50 [mac80211]
[<fc1e5b22>] ath_tx_complete_poll_work+0xb2/0x100 [ath9k]
[<c016399e>] run_workqueue+0x8e/0x150
[<fc1e5a70>] ? ath_tx_complete_poll_work+0x0/0x100 [ath9k]
[<c0163ae4>] worker_thread+0x84/0xe0
[<c0167a60>] ? autoremove_wake_function+0x0/0x50
[<c0163a60>] ? worker_thread+0x0/0xe0
[<c01677d4>] kthread+0x74/0x80
[<c0167760>] ? kthread+0x0/0x80
[<c0104087>] kernel_thread_helper+0x7/0x10
---[ end trace 2aff81010df9215b ]---
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when aggregation protection mode is enabled the hardware needs
to send RTS/CTS for each HT frame. Currently its disabled so
remove the unused call backs.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While draining the txq in flush, the buffers can be
added into the tx queue by tx_tasklet which leads to
unneccesary chip reset.
This issue was originially found with AR9382 and
running heavy uplink udp traffic with higher bandwidth
and doing frequent bgscan.
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Requesting beacon sync up to configure beacon timers properly
in hw, has be done after doing beacon config with default values.
Setting the flags in beacon config is causing the device to not
enter into network sleep on idle state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should protect hw_pll handler with power save wrappers and
also modularize hw_pll handler properly for better readability.
Also add a debug message to track chip resets on pll hang condition.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason why pll work handler should be part of xmit
file. move it to main.c so that reading hw check routines are
all in the same place.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need not wake up the chip even before mutex lock is acquired and also
that it is required only if we are going to drain the txq. So place the
wrappers accordingly and this change is also useful when there are no
pending frames in the txq as we do not wake up the chip unnecessarily.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frame filtering relies on having a valid destination index (keycache slot),
to keep track of the destination. Assigning a keycache slot (configured
to unencrypted, with no key data attached) improves powersave handling in
AP mode with no encryption.
The dummy keycache entry for a station is cleared, when a real key gets
added.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a long standing issue of pending packets in the queue being
sent (and retransmitted many times) to sleeping stations.
This was made worse by aggregation through driver-internal retransmitting
of A-MDPU subframes.
Previously the hardware tx filter was cleared unconditionally for every
single packet - with this patch it uses the IEEE80211_TX_CTL_CLEAR_PS_FILT
for unaggregated frames.
A sta_notify driver op is added to stop aggregation for stations when they
enter powersave mode. Subframes stay buffered inside the driver, to ensure
that the BlockAck window keeps a sane state.
Since the driver uses software aggregation, the clearing of the tx filter
needs to be handled by the driver instead of mac80211 for aggregated frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: configure beacons based on hw opmode" introduced
a regression which leads to kernel panic. Failed to stop ani timer
during the driver unload while any of the beaconing vif is running.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function returns true if there is atleast one frame
in any one of the tx queues.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These missing chip wakeups mainly cause crashes on AR5416 cards in MIPS
boards, but have also been reported to cause radio stability issues on
AR9285.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current ath9k code does not handle beacon timers on opmode
specific. One such example is that a STA beacon config overwrites
already configured AP vif's beacon timers during scan.
On multi station vif case, configure beacon timers beased
on primary vif selected. This also helps while moving back
to single STA vif from multi STA vifs, where the power save
is enabled and hw has to be reconfigured with proper
beacon and bssid/aid. Otherwise connection poll will be triggered
so frequently due to beacon loss.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now bssid/aid is overridden with recently changed vif's
bss config. This may cause improper beacon updation due to
bssid/aid mismatch. On station mode, select an associated
sta vif as primary vif and configure that vif's bss into hw.
Update the primary vif on interface change and bss info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused bssid from ath_vif and set av_bslot on beacon
alloc/return.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The present check denies the IBSS interface addtion if we
already have any other vifs. But it fails to deny interface
addition if IBSS was already present.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for using RSN IBSS with ath9k. For now, this uses software
crypto for group addressed frames in RSN IBSS, but that may be
optimized in the future by extending the key cache design to support
per-STA RX GTK.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is still asleep when ath9k_start is called,
ath9k_hw_configpcipowersave can trigger a data bus error.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 86271e460a introduced a
regression that caused mac80211 queues in stopped state.
ath_drain_all_txq is called in driver flush which would reset
the stopped flag and the mac80211 queues were never started
after that. iperf traffic is completely stalled due to this issue.
Restart the mac80211 queues in driver flush only if the txqs were
drained.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the flush op and reuses ath_drain_all_txq for
flushing out pending frames if necessary. It also uses a global timeout
of 200ms instead of the per-queue 60ms timeout.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize txq to avoid this warning:
drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_flush’:
drivers/net/wireless/ath/ath9k/main.c:2138: warning: ‘txq’ may be used uninitialized in this function
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pll_work should be cancelled on full_sleep or it may cause
redundant chip reset.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).
Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.
Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When op_flush() is called with no drop (drop=false), the driver
tries to tx as many frames as possible in about 100ms on every
hw queue. During this time period frames from sw queue are also
scheduled on to respective hw queue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beaconing should be disabled before stopping beacon queue.
Not doing so could queue up beacons in hw that causes
failure to stop Tx DMA, due to pending frames in hw
and also unnecessary beacon tasklet schedule.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable appears in both ath_softc and ath_beacon_config.
The struct ath_beacon_config is embedded in ath_softc. The redundant
variable was added by commit id 57c4d7b4c4.
Signed-off-by: Steve Brown <sbrown@cortland.com>
Reviewed-by: Mohammed Shafi <shafi.ath9k@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since even with the latest changes the false positive issue of the baseband
hang check is not fully solved yet, additional checks are needed.
If the baseband hang occurs, the rx_clear signal will be stuck to high, so
we can use the cycle counters to confirm it.
With this patch, a hardware reset is only triggered if the baseband hang
check returned true three times in a row, with a beacon interval between
each check and if the busy time was also 99% or more during the check
intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beaconing vif addition is based on max beacon slot
available. So it is better to reserve a beacon slot
on interface addition and let it be configured properly
on bss_info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The opmode recalculation is accessing hw registers.
When it is called from remove interface callback and
if there are no vifs present then hw is moved to FULL SLEEP
by radio disable. So use power save wrappers before
accessing hw registers in calculating opmode state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
move ath_update_txpow to common to remove code duplication
in both ath9k & ath9k_htc.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this PLL hang issue is seen, both Rx and Tx fail to work.
The sqsum_dvc needs to be below 2000 for a good chip. During
this issue the sqsum_dvc value is beyond 80000 and only a
full reset can solve this problem.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this change, less CPU time is spent trying to look for consecutive
pages for rx skbs. This also reduces the socket memory required for IP/UDP
reassembly.
Only two buffers per frame are supported. Frames spanning more buffers
will be dropped, but the buffer size is enough to handle the required
AMSDU size.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of spreading ath_wake_mac80211_queue() calls over multiple places
in the tx path that process the tx queue for completion, call it only
where the pending frames counter gets decremented, eliminating some
redundant checks.
To prevent queue draining from waking the queues prematurely (e.g. during
a hardware reset), reset the queue stop state when draining all queues,
as the caller in main.c will run ieee80211_wake_queues(hw) anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.
This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.
ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.
I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stations hold the ath_node, which holds the tid
and other xmit logic structures. In order to debug
stuck xmit logic, we need a way to print out the tid
state for the stations.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several places where ath_reset() was called without proper
calls to ath9k_ps_wakeup/ath9k_ps_restore. To fix this, add those calls
directly to ath_reset and drop them from callers where it makes sense.
Also add them to the config callback around ath_update_txpow to fix a
crash that happens when the tx power changed before any vif is brought up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.
In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.
Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using a mixture of AP and Station interfaces,
the hardware mode was using the type of the
last VIF registered. Instead, we should keep track
of the number of different types of vifs and set the
mode accordingly.
In addtion, use the vif type instead of hardware opmode
when dealing with beacons.
Attempt to move some of the common setup code into smaller
methods so we can re-use it when changing vif mode as
well as adding/deleting vifs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since baseband hangs are rare, but the hang check function has a high
false positive rate in some situations, we need to add more reliable
indicators.
In AP mode we can use blocked beacon transmissions as an indicator,
they should be rare enough.
In station mode, we can skip the hang check entirely, since a true
hang will trigger beacon loss detection, and mac80211 will rescan,
which leads to a hw reset that will bring the hardware back to life.
To make this more reliable, we need to skip fast channel changes
if the hardware appears to be stuck.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restart the beacon timers only if the beacon
was already configured. Otherwise beacons timers
are restarted unnecessarily in unassociated state too.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disabling BH is not required while running from a tasklet context
and so replace spin_lock_bh with just spin_lock.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a missing unlock when we hit the "No beacon slot available"
error condition.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restricting the chainmask to 1 for legacy mode disables useful features
such as MRC, and it reduces the available transmit power.
I can't think of a good reason to do this in legacy mode, so let's just
get rid of that code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Target Tx power available in eeprom is for PAPRD. If PAPRD
fails, paprd scale factor needs to be detected from this
target tx power.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PM-QOS value can be user specified via module parameter.
This patch adds few comments regarding this in the driver
code.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the pm-qos value to be user configurable by making it as
a module parameter.This will help our customers to configure the pm-qos
value according to the effect in throughput due to the DMA latency problem
which was observed in Intel Pinetrail platforms.
The tested value of '55' will be filled as the default
pm-qos-value incase the user does not specifies pm-qos value as a
module parameter.
example usage: sudo modprobe ath9k pmqos=65
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM contains scale factors for the tx power, which define
the range of allowable difference between target power and training
power. If the difference is too big, PA predistortion cannot be used.
For 2.4 GHz there is only one scale factor, for 5 GHz there are
three, depending on the specific frequency range.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be able to measure the thermal values correctly for PAPRD, we need
to send training frames before setting up the gain table for the measurement,
and then again afterwards for the actual training.
For further improvement, send training frames at MCS0 instead of 54 MBit/s
legacy. That way we can use the No-ACK flag for the transmission, which
speeds up PAPRD training in general, as the hardware won't have to
retransmit and wait for ACK timeout (was previously set to 4 * 6
transmission attempts).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be awake when accessing registers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to change interface type
without bringing down the interface.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 will notify drivers when to go idle and ath9k
assumed that it would get further notifications for idle
states after a device stop() config call but as per agreed
semantics the idle state of the radio is left up to driver
after mac80211 issues the stop() callback. The driver is
resposnbile for ensuring the device remains idle after
that even between suspend / resume calls.
This fixes suspend/resume when you issue suspend and resume
twice on ath9k when ath9k_stop() was already called. We need
to put the radio to full sleep in order for resume to work
correctly.
What might seem fishy is we are turning the radio off
after resume. The reason why we do this is because we know
we should not have anything enabled after a mac80211 tells
us to stop(), if we resume and never get a start() we won't
get another stop() by mac80211 so to be safe always bring
the 802.11 device with the radio disabled after resume,
this ensures that if we suspend we already have the radio
disabled and only a start() will ever trigger it on.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon a failure we never call ath9k_ps_restore() on ath_radio_enable(),
this will throw off the sc->ps_usecount. When the sc->ps_usecount
is > 0 we never put the chip to full sleep. This drains battery,
and will also make the chip fail upon resume with:
ath: Starting driver with initial channel: 5745 MHz
ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
This would make the chip useless upon resume.
I cannot prove this can happen but in theory it is so best to
avoid this race completely and not have users complain about
a broken device after resume.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not be idle when we get the ATH9K_INT_TIM_TIMER,
otherwise its a sign of something broken in our design with
our idle state machine and mac80211. Skip these and WARN once
just in case this is triggerable.
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So these errors are always emitted at KERN_ERR level.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon tasklet is accesssing the bslot info for beacon generation.
Meanwhile the same slot can be freed on interface deletion.
Current the remove_interface disables the beacon alert after freeing the slot.
This may leads to null pointer access.
This patch disables SWBA and kills the beacon tasklet to prevent access
to the slot to be freed. After releasing the slot, swba will be enabled again
upon the availablity of beaconing interfaces.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset
happens at a very problematic point in time, when the hardware rx path has
not been stopped yet. This could lead to memory corruption, hardware hangs
or other issues.
To fix these issues, simply remove the reset entirely and check the tx DMA
stop status to prevent problems with fast channel changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature is to mitigate the problem of certain 3
stream chips that exceed the PCIe power requirements.An EEPROM flag
controls which chips have APM enabled which is basically read from
miscellaneous configuration element of the EEPROM header.
This workaround will reduce power consumption by using 2 Tx chains for
Single and Double stream rates (5 GHz only).All self generated frames
(regardless of rate) are sent on 2 chains when this feature is
enabled(Chip Limitation).
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Tested-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
while removing beaconing mode interface, SWBA interrupt
was never disabled when there are no other beaconing interfaces.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver uses a shared pm_qos_request_list structure for all
devices. This causes the following warning if more than one device is
present in the system:
WARNING: at kernel/pm_qos_params.c:234 ath9k_init_device+0x5e8/0x6b0()
pm_qos_add_request() called for already added request
Modules linked in:
Call Trace:
[<802b1cdc>] dump_stack+0x8/0x34
[<8007dd90>] warn_slowpath_common+0x78/0xa4
[<8007de44>] warn_slowpath_fmt+0x2c/0x38
[<801b0828>] ath9k_init_device+0x5e8/0x6b0
[<801bc508>] ath_pci_probe+0x2dc/0x39c
[<80176254>] pci_device_probe+0x64/0xa4
[<8019471c>] driver_probe_device+0xbc/0x188
[<80194854>] __driver_attach+0x6c/0xa4
[<80193e20>] bus_for_each_dev+0x60/0xb0
[<80193580>] bus_add_driver+0xcc/0x268
[<80194c08>] driver_register+0xe0/0x198
[<801764e0>] __pci_register_driver+0x50/0xe0
[<80365f48>] ath9k_init+0x3c/0x6c
[<8006050c>] do_one_initcall+0xfc/0x1d8
[<80355340>] kernel_init+0xd4/0x174
[<800639a4>] kernel_thread_helper+0x10/0x18
---[ end trace 5345fc6f870564a6 ]---
This patch fixes that warning by using a separate pm_qos_request_list
sructure for each device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge initial processing for the CAB queue and regular tx.
Also move ath_tx_cabq() to beacon.c and make it static.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current ath9k tx queue handling code showed a few issues that could
lead to locking issues, tx stalls due to stopped queues, and maybe even
DMA issues.
The main source of these issues is that in some places the queue is
selected via skb queue mapping in places where this mapping may no
longer be valid. One such place is when data frames are transmitted via
the CAB queue (for powersave buffered frames). This is made even worse
by a lookup WMM AC values from the assigned tx queue (which is
undefined for the CAB queue).
This messed up the pending frame counting, which in turn caused issues
with queues getting stopped, but not woken again.
To fix these issues, this patch removes an unnecessary abstraction
separating a driver internal queue number from the skb queue number
(not to be confused with the hardware queue number).
It seems that this abstraction may have been necessary because of tx
queue preinitialization from the initvals. This patch avoids breakage
here by pushing the software <-> hardware queue mapping to the function
that assigns the tx queues and redefining the WMM AC definitions to
match the numbers used by mac80211 (also affects ath9k_htc).
To ensure consistency wrt. pending frame count tracking, these counters
are moved to the ath_txq struct, updated with the txq lock held, but
only where the tx queue selected by the skb queue map actually matches
the tx queue used by the driver for the frame.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps align resets / RX enable & disable / TX stop / start.
Locking around the PCU is important to ensure the hardware doesn't
get stale data when working with DMA'able data.
This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCU lock should be used to contend TX DMA as well,
this will be done next.
This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new PCU lock is better placed so we can just contend
against that when trying to reset hardware.
This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_set_txpowerlimit gets an extra boolean parameter that - if set -
causes the rate txpower table and the regulatory limit to be calculated
and stored, without changing hardware registers.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI needs the RSSI average only in station mode, and only for tracking
the signal strength of beacons of the AP that it is connected to.
Adjust the code to track on the beacon RSSI, and store the average of that
in the ath_wiphy struct.
With these changes, we can get rid of this extra station lookup in the
rx path, which saves precious CPU cycles.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OProfile showed that ath9k was spending way too much time in
ath9k_hw_set_interrupts. Since most of the interrupt mask changes only
need to globally enable/disable interrupts, it makes sense to split
this part into separate functions, replacing all calls to
ath9k_hw_set_interrupts(ah, 0) with ath9k_hw_disable_interrupts(ah).
ath9k_hw_set_interrupts(ah, ah->imask) only gets changed to
ath9k_hw_enable_interrupts(ah), whenever ah->imask was not changed
since the point where interrupts were disabled.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_ps_wakeup() clears the cycle counters after waking up the
hardware using ath9k_hw_setpower, however if power save is disabled,
then the counters will contain useful data, which then gets discarded.
Fix this by checking the old power mode before discarding any data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Throughput was severely affected in Intel Pinetrail platforms
because of a DMA problem in C3 state. This patch fixes this
issue.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW opmode is blindly set to monitor type on monitor mode
change notification. This overrides the opmode when one of the
interfaces is still running as non-monitor iftype. So the monitoring
information needs to be maintained seperately.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apart from locking the start and stop PCU we need
to ensure we also content starting and stopping the PCU
between hardware resets.
This is part of a series that will help resolve the bug:
https://bugzilla.kernel.org/show_bug.cgi?id=14624
For more details about this issue refer to:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The real way to lock RX is to contend on the PCU
and reset, this will be fixed in the next patch but for
now just do the renames so that the next patch which changes
the locking order is crystal clear.
This is part of a series that will help resolve the bug:
https://bugzilla.kernel.org/show_bug.cgi?id=14624
For more details about this issue refer to:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since aggregation is usually triggered by tx completion, a hardware
reset (because of beacon stuck, tx hang or baseband hang) can
significantly delay the transmission of the next AMPDU (until the next
tx completion event).
Fix this by rescheduling aggregation after such a reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If ah->curchan is uninitialized, the channel index is bogus, which leads
to invalid memory access when the cycle counters are updated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the rate table in the rc module properly based on band and
HT capabilities instead, which was already partially done, but
not for every mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_proc_mib_event updates the cycle counters, so it common->cc_lock
must be acquired.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While the chip is in powersave mode, the cycle counter updates do not
contain useful values. While the chip is in full sleep, the rx_clear
signal stays high, indicating a busy medium.
To ensure sane values, update cycle counters before going into
powersave, and clear them right after switching back to awake.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows mac80211 to enable receiving of Probe Request frames in
station mode which is needed for P2P.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Results for the active channel are updated whenever a new survey dump
is requested, the old data is kept to allow multiple processes to
make their own channel utilization averages.
All other channels only contain the data for the last time that the
hardware was on the channel, i.e. the last scan result or other
off-channel activity.
Running a background scan does not clear the data for the active
channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of keeping track of wraparound, clear the counters on every
access and keep separate deltas for ANI and later survey use.
Also moves the function for calculating the 'listen time' for ANI
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drv_config callback is called only after the ack for the nullframe
is received and so driver need not do anything special for this.
So remove NULLFUNC_COMPLETED, PS_ENABLED flags and bf_isnullfunc
flags from ath9k as mac80211 already handles them properly.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split out the PHY error counter update from ath9k_hw_ani_monitor_*, reuse
it in ath9k_hw_proc_mib_event (merged from ath9k_hw_proc_mib_event_old
and ath9k_hw_proc_mib_event_new).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
common->ani.noise_floor is now only used for a similar redundant debug
message similar to the one that was removed from ath9k_htc in an earlier
patch. Remove it from ath9k as well now.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paprd needs to be done only on active chains(not for all the chains
that hw can support). The paprd training frames which are sent
for inactive chains would be hanging on the hw queue without
getting transmitted and would make the connection so unstable.
This issue happens only with the hw which supports paprd cal(ar9003).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new aggregation session start can be issued by mac80211, even when the
cleanup of the previous session has not completed yet. Since the data structure
for the session is not recreated, this could corrupt the block ack window
and lock up the aggregation session. Fix this by delaying the new session
until the old one has been cleaned up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k's entire logic with SC_OP_SCANNING is incorrect due to the
way mac80211 currently implements the scan complete callback and
we handle it in ath9k. This patch removes the flag completely in
preference for the SC_OP_OFFCHANNEL which is really what we wanted.
The scanning flag was used to ensure we reset ANI to the old values
when we go back to the home channel, but if we are offchannel we
use some defaults. The flag was also used to re-enable the TX monitor.
Without this patch we simply never re-enabled ANI and the TX monitor
after going offchannel. This means that after one background
scan we are prone to noise issues and if we had a TX hang we would
not recover. To get this to work properly we must enable ANI after
we have configured the beacon timers, otherwise hardware acts really
oddly.
This patch has stable fixes which apply down to [2.6.36+], there
*may* be a to fix this on older kernels but requires a bit of
work since this patch relies on the new mac80211 flag
IEEE80211_CONF_OFFCHANNEL which was introduced as of 2.6.36.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we return to the home channel we were never reseting our beacon
timers, this was casued by the fact that the scanning flag was still
on even after we returned to our home channel. There are also other
reasons why we would get a reset and if we are not off channel
we always need to resynch our beacon timers, because a reset will
clear them.
This bug is a regression introduced on 2.6.36. The order of the
changes are as follows:
5ee08656 - Sat Jul 31 - ath9k: prevent calibration during off-channel activity
a0daa0e7 - Tue Jul 27 - Revert "mac80211: fix sw scan bracketing"
543708be - Fri Jun 18 - mac80211: fix sw scan bracketing
mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
--contains 5ee0865615
v2.6.36-rc1~43^2~34^2~22
mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
--contains a0daa0e759
v2.6.36-rc1~571^2~64^2~13
mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
--contains 543708be32
v2.6.36-rc1~571^2~107^2~187
So 5ee08656 would have worked if a0daa0e7 was not committed but
it was so this means 5ee08656 was broken since it assumed that
when we were in the channel change routine the scan flag would
be lifted. As it turns out the scan flag will be set when we
are already on the home channel.
For more details refer to:
http://code.google.com/p/chromium-os/issues/detail?id=5715
These issues will need to be considered for our solution on
reshifting the scan complete callback location on mac80211 on
current development kernel work.
This patch has stable fixes which apply down to [2.6.36+]
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k has a race on putting the chip into network sleep and
having registers read from hardware. The race occurs because
although ath9k_ps_restore() locks its own callers it makes use
of some variables which get altered in the driver at different
code paths. The variables are the ps_enabled and ps_flags.
This is easily reprodicible in large network environments when
roaming with the wpa_supplicant simple bgscan. You'd get some
0xdeadbeef read out on certain registers such as:
ath: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000 != 0x00000000
ath: RX failed to go idle in 10 ms RXSM=0xdeadbeef
ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
ath: Chip reset failed
The fix is to protect the ath9k_config(hw, IEEE80211_CONF_CHANGE_PS)
calls with a spin_lock_irqsave() which will disable contendors for
these variables from interrupt context, timers, re-entry from mac80211
on the same callback, and most importantly from ath9k_ps_restore()
which is the only call which will put the device into network sleep.
There are quite a few threads and bug reports on these a few of them are:
https://bugs.launchpad.net/ubuntu/karmic/+source/linux/+bug/407040http://code.google.com/p/chromium-os/issues/detail?id=5709http://code.google.com/p/chromium-os/issues/detail?id=5943
Stable fixes apply to [2.6.32+]
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use key management functions which have been moved to ath/key.c and remove
ath9k copies of these functions and other now unused definitions.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the time the .add_interface driver op is called, the interface has not
been marked as running yet, so ieee80211_iterate_active_interfaces will
not pass it to the iterator function.
Because of this, the calculated BSSID mask is wrong, which breaks multi-BSS
operation.
Additionally, the current way of comparing all addresses against each other
is pointless, as the hardware only uses the hardware MAC address and the BSSID
mask for matching the destination address, so all the address array
reallocation is completely unnecessary.
This patch simplifies the logic by setting the initial mask bytes to 0xff
and removing all bits in the iterator call that don't match the hardware MAC
address. It also calls the iterator for the vif that was passed to
add_interface()
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the noise floor limits are being bypassed because of strong
interference, sensitivity is also reduced.
In order to recover from this as quickly as possible, trigger a
long periodic calibration every second instead of every 30 seconds,
until the NF median is within limits again. This is especially important
if the interference lasts for a while, since it takes multiple clean
NF calibrations to bring the median back to normal.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps us debug channel changes better.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.
This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.
For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.
For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the software scan callback was used to indicate to the hardware,
when it was safe to calibrate. This didn't really work properly, because it
depends on a specific order of software scan callbacks vs. channel changes.
Also, software scans are not the only thing that triggers off-channel
activity, so it's better to use the newly added indication from mac80211 for
this and not use the software scan callback for anything calibration related.
This fixes at least some of the invalid noise floor readings that I've seen
in AP mode on AR9160
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When updating the PAPRD table in hardware, PAPRD itself needs to be
disabled first, otherwise the hardware can throw a data bus error,
which upsets at least some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issuing two consecutive scans you could often end up
getting in the logs:
"ath9k: Two wiphys trying to scan at the same time"
This message is due to a race in mac80211 but addressing
that race requires some more major changes on the driver
and perhaps optimizations on mac80211 like removing the
scan complete callback alltogether. Its too late to address
this this kernel release so supress the complaint and annotate
this needs fixing for later.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/main.c:282:26: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/main.c:282:26: expected restricted __le16 [usertype] duration_id
drivers/net/wireless/ath/ath9k/main.c:282:26: got int
Signed-off-by: John W. Linville <linville@tuxdriver.com>
num_sec_wiphy means max secondary wifis that the driver can accomudate.
So cancelling wiphy work should be based on the presence of
secondary wifis.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED should be ON when the radio is put into FULL SLEEP mode during the idle
unassociated state.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_check_alive() occasionally returns false, as the hardware
is still processing data in a specific state. Fix this issue by
repeating the test a few times with longer delay inbetween attempts.
This gets rid of excessive hardware resets that appear frequently on
some AR9132 based devices, but could also happen on AR9280.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move ath9k_ps_wakeup() down just before accessing hw registers.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possbile that the transmission of paprd test frame
might not get completed in 100ms if tx is stuck. Freeing
this skb upon timeout in ath_paprd_calibrate() will result
in accessing already freed memory when the associated pending
buffer is drained in txq. This patch fixes this issue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are few places where ANI is started without checking
if it is right to start. This might lead to a case where ani
timer would be left undeleted and cause improper memory acccess
during module unload. This bug is clearly exposed with
paprd support where the driver detects tx hang and does a
chip reset. During this reset ani is (re)started without checking
if it needs to be started. This would leave a timer scheduled
even after all the resources are freed and cause a panic.
This patch introduces a bit in sc_flags to indicate if ani
needs to be started in sw_scan_start() and ath_reset().
This would fix the following panic. This issue is easily seen
with ar9003 + paprd.
BUG: unable to handle kernel paging request at 0000000000003f38
[<ffffffff81075391>] ? __queue_work+0x41/0x50
[<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370
[<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110
[<ffffffff81061f69>] __do_softirq+0xb9/0x1f0
[<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160
[<ffffffff8100af5c>] call_softirq+0x1c/0x30
[<ffffffff8100c9f5>] do_softirq+0x65/0xa0
[<ffffffff81061e25>] irq_exit+0x85/0x90
[<ffffffff8155e095>] do_IRQ+0x75/0xf0
[<ffffffff815570d3>] ret_from_intr+0x0/0x11
<EOI>
[<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119
[<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119
[<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140
[<ffffffff81008da3>] cpu_idle+0xb3/0x110
[<ffffffff81550722>] start_secondary+0x1ee/0x1f5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendors require the LED to be ON always irrespective of any
radio activity. Introducing a module parameter to disable blinking,
so that one can choose between always on or led blink during
activity.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace calls that read this capability with accesses to ath9k_hw's
regulatory data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.
The old ANI implementation is left intact.
Details of the new ANI implemention:
* ANI adjustment logic is now table driven so that each ANI level
setting is parameterized. This makes adjustments much more
deterministic than the old procedure based logic and allows
adjustments to be made incrementally to several parameters per
level.
* ANI register settings are now relative to INI values; so ANI
param zero level == INI value. Appropriate floor and ceiling
values are obeyed when adjustments are combined with INI values.
* ANI processing is done once per second rather that every 100ms.
The poll interval is now a set upon hardware initialization and
can be picked up by the core driver.
* OFDM error and CCK error processing are made in a round robin
fashion rather than allowing all OFDM adjustments to be made
before CCK adjustments.
* ANI adjusts MRC CCK off in the presence of high CCK errors
* When adjusting spur immunity (SI) and OFDM weak signal detection,
ANI now sets register values for the extension channel too
* When adjusting FIR step (ST), ANI now sets register for FIR step
low too
* FIR step adjustments now allow for an extra level of immunity for
extremely noisy environments
* The old Noise immunity setting (NI), which changes coarse low, size
desired, etc have been removed. Changing these settings could affect
up RIFS RX as well.
* CCK weak signal adjustment is no longer used
* ANI no longer enables phy error interrupts; in all cases phy hw
counting registers are used instead
* The phy error count (overflow) interrupts are also no longer used
for ANI adjustments. All ANI adjustments are made via the polling
routine and no adjustments are possible in the ISR context anymore
* A history settings buffer is now correctly used for each channel;
channel settings are initialized with the defaults but later
changes are restored when returning back to that channel
* When scanning, ANI is disabled settings are returned to (INI) defaults.
* OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
low/high water marks, providing increased stability/hysteresis when
changing levels.
* Similarly CCK phy error thresholds are now 300 & 600 (errors/second)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because there is a limited number of tx buffers available, once the
queue has been filled to a certain point, ath9k needs to stop accepting
new frames from mac80211. In order to prevent a full WMM queue from
stopping another queue with fewer frames, this patch limits the number
of queued frames to a quarter of the total available tx buffers, minus
some reserved frames to be used for other purposes (e.g. beacons).
Because tx buffers are reserved for frames when they're staged in
software queues as well, the actual queue depth cannot be used for
this, so this patch stores a reference to the tx queue in the ath_buf
struct and keeps track of the total number of pending frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx should not be disabed/disabled when hw supports auto sleeping.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables the baseband watchdog events for the AR9003
family on ath9k. Upon an a baseband watchdog interrupt we reset
the hardware, this should address corner case conditions where
normal operation can stall. Enable ATH_DBG_RESET to be able
to review details of the bb watchdog interrupt once it happens.
If you're curious how often this happens just grep the debugfs
interrupt file.
Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.
The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.
It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.
I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.
Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.
Signed-off-by: Daniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ah variable in the functions that didn't have it and used sc->imask.
Replace sc->sc_ah with ah in those functions.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts ath9k to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If split tkip key is used, ath_delete_key should delete
rx key and rx mic key. This patch fixes the leak of hw
keycache in the case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM timer interrupt is enabled even before the ACK of nullqos
is received which is unnecessary.
Also clean up the CONF_PS part of config callback properly for
better readability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Numeric channel is hard to get, so it won't be printed. Replace Mhz
with MHz on the affected lines and add commas as needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IDLE PS (Full Sleep) doesn't work when ifconfig up
is done during Idle unassociated state.
Fix this by restoring FULL SLEEP in ps_restore if CONF_IDLE
is set.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cleaning up beacon buffers and slots, ath9k currently checks if
sc->ah->opmode is set to a beacon related mode before cleaning up
buffers.
An unfortunate ordering of interface up/down commands can lead to
sc->ah->opmode being set to monitor mode, while there are AP interfaces
present on the same wiphy.
Always cleaning up beacon buffers if present fixes this issue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users wishing to tweak tx power want it to happen immediately,
try to respect that. This was tested by Lorenzo by measuring the
received signal strength from an AP with ath9k and the patch.
Changing the tx power on the AP produced these results:
1) iwconfig wlan0 txpower 20 ---> Rx power -37dbm
2) iwconfig wlan0 txpower 15 ---> Rx power -41dbm
3) iwconfig wlan0 txpower 10 ---> Rx power -45dbm
4) iwconfig wlan0 txpower 5 ---> Rx power -51dbm
5) iwconfig wlan0 txpower 0 ---> Rx power -37dbm
The result with 0 is an anomoly and would need to be
addressed through a separate patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously ath9k left the initialization of slot timing and ACK/CTS
timeout to the mode specific initvals. This does not handle short vs
long slot in 2.4 GHz and uses a rather strange value for the 2.4 GHz
ACK timeout (64 usec).
This patch uses the proper ath9k_hw functions for setting slot time and
timeouts and also implements the switch between short and long slot
time in 2.4 GHz
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 passes appropriate flags indicating whether
monitor mode is being used. Use this to set the HW opmode.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX queues have to be stopped during an
internal reset. Not handling this would result
in packet loss - fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sc_flags has slowly become a kitchen sink over time.
Move powersave related flags to a separate variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move initialization/de-initialization related
code to this file.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all LED/RFKILL/BTCOEX related code
to gpio.c
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The newer single chip hardware family of chipsets have not been
experiencing issues with power saving set by default with recent
fixes merged (even into stable). The remaining issues are only
reported with AR5416 and since enabling PS by default can increase
power savings considerably best to take advantage of that feature
as this has been tested properly.
For more details on this issue see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=14267
We leave AR5416 with PS disabled by default, that seems to require
some more work.
Cc: stable@kernel.org
Cc: Peter Stuge <peter@stuge.se>
Cc: Justin P. Mattock <justinmattock@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMDPDU actions poke hardware for TX operation, as such
we want to turn hardware on for these actions. AMDPU RX operations
do not require hardware on as nothing is done in hardware for
those actions. Without this we cannot guarantee hardware has
been programmed correctly for each AMPDU TX action.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove a IBSS/AP/Mesh interface we stop DMA
but to do this we should ensure hardware is on. Awaken
the device prior to these calls. This should ensure
DMA is stopped upon suspend and plain device removal.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure the device is awake prior to trying to tell hardware
to stop it. Impact of not doing this is we can likely leave
the device in an undefined state likely causing issues with
suspend and resume. This patch ensures harware is where it
should be prior to suspend.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable the TX hang monitoring routine when doing a scan.
Monitoring for a hung situation is not really necessary during
a scan run.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cancel/restart the ANI timer directly.
With this patch, the ANI lock can be removed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIB counters are disabled when doing a chip reset.
Since ANI depends on the MIB registers for its operation, relying
on the contents of said registers during HW reset results in sub-optimal
performance.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the 2GHz band is enabled unconditionally, even if the device
does not support it.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the beacon queue parameters with best effort queue parameters for
IBSS mode. This reduces the number of beacons generated by ath9k and
ensures a fair beacon distribution when there are multiple IBSS stations.
Also CWmin is quadrupled to achieve the expected percentage of
distribution.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Software padding is done on the TX path and software unpadding is done on the
RX path. This patch corrects the position where the padding occurs. A specific
function computes the pad position and this function is used in the TX and RX
path. This patch has been tested by generating every possible 802.11 frames
with every possible frame_control field and a varying length. This patch is
useful for analyzing non standard 802.11 frames going over the air
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 was telling us to go into Powersave we listened
and immediately turned RX off. This meant hardware would not
see the ACKs from the AP we're associated with and hardware
we'd end up retransmiting the null data frame in a loop
helplessly.
Fix this by keeping track of the transmitted nullfunc frames
and only when we are sure the AP has sent back an ACK do we
go ahead and shut RX off.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Vivek Natarajan <Vivek.Natarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes ath9k to pass proper MCS indexes and flags
between the RC and the rest of the driver code.
sc->cur_rate_table remains, as it's used by the RC code internally,
but the rest of the driver code no longer uses it, so a potential
new RC for ath9k would not have to update it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copied from original one-line patch here:
http://bugzilla.kernel.org/show_bug.cgi?id=14267#c26
(This is for 2.6.33 and beyond, where the bool was changed to a flag by
"cfg80211: convert bools into flags". -- JWL)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The entire aggregation code currently operates on the
hw pointer and station addresses, but that needs to
change to make stations purely per-vif; As one step
preparing for that make the aggregation code callable
with the station, or by the combination of virtual
interface and station address.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Remove a code chunk dealing with operating mode changes.
As noted, all such policy changes are to be done in
add_interface.
* Remove pointless check for empty BSSID.
Also, remove mode checks - mac80211 does all the needed checks.
* Handle enabling/disabling beacon transmission properly.
* Handle beacon interval changes for AP mode.
The original code depended on config_interface() to update
the HW TSF. Since that callback has been removed, handle
it properly.
* Remove unneeded code dealing with key/privacy.
* Set the chainmasks to 1x1 for IBSS when the BSSID is set.
This was happening uncondionally before.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will make sharing code easier between ath9k and ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be shared between ath9k and ath9k_htc. It will also
help with sharing routine helpers on the RX path.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use the ieee80211_hw for radio enable/disable but the wrong
structure hw was being used in consideration for virtual wiphys
as each virtual wiphy has its own ieee80211_hw struct.
Just pass the hw struct to ensure we use the right one. This should
fix the hw used and passed for radio enable/disable. This includes
the stoping / starting of the software TX queues so mac80211 doesn't
send us data for a specific virtual wiphy. ath9k already takes care
of pausing virtual wiphys and stopping the respective queues on its
own, but this should handle the idle mac80211 conf calls as well.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way idle configuration detection was implemented as
busted due to the fact that it assumed the ath9k virtual wiphy,
the aphy, would be marked as inactive if it was not used but
it turns out an aphy is always active if its the only wiphy
present. We need to distinguish between aphy activity and
idleness so we now add an idle bool for the aphy and mark
it as such based on the passed IEEE80211_CONF_CHANGE_IDLE
from mac80211.
Previous to all_wiphys_idle would never be true when using
only one device so we never really were using
IEEE80211_CONF_CHANGE_IDLE -- we never turned the radio
off or on upon IEEE80211_CONF_CHANGE_IDLE changes as radio
changes depended on all_wiphys_idle being true either to
turn the radio on or off. Since it was always false for
one device this code was doing nothing.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are shared between ath9k and the future ath9k_htc driver.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
