The 'else if' branch never gets the chance as its condition
matches 'if' branch's.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes pending internal scan commands are delayed to give
preference to Tx traffic. 'scan_processing' flag has been
checked at the beginning of delay timer routine to know if in the
meantime scan operation has been cancelled.
There is a corner case where pending scan commands are emptied
after scan_processing flag check is passed. In this case
wrong pointer returned by list_first_entry() is passed to
list_del() which causes system hang.
This patch fixes the issue by adding list_empty() check.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in which rx_reorder_tbl_ptr is accessed
without holding spinlock at few places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The *_bit operations expect unsigned longs.
Instead of casting the pointers, simply define various
bitmaps as unsigned long (instead of u32).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some corner cases with specific timings, we might
try dequeueing tx before we got information about
the link status (e.g. due to recovery during tx).
Instead of NULL dereference, assume all
the links in this case have low priorities.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each 18xx chip contains only 2 real MAC addresses
usable for WLAN, forcing us to use the LAA bit
approach to obtain a third MAC address.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sending the FW a channel switch command on a disconnected
vif may result in a beacon loss event. Avoid this corner case.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the smart config code is in place now,
so register the relevant vendor commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we don't have any actual limitation in the driver, so
increase it arbitrarily to 30 seconds.
The long ROC is needed for the smart config.flow.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add defintions and handling for smart config events
(SMART_CONFIG_SYNC_EVENT_ID and SMART_CONFIG_DECODE_EVENT_ID)
parse the relevant info and send it to userspace as
vendor event.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
userspace can ask to perform various smart config
actions via custom vendor commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These commands configures the fw to set key,
enter smart config mode, and exit it.
Add relevant hw ops as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LAA bit is second bit of the MSB, not of the
third byte.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last tx rate calculation didn't take into account
the different indices of 11a and 11g rates tables.
Add the required alignment (count only from the first
11a rate in case of 11a)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On recovery, we increase the current seq num by
WL1271_TX_SQN_POST_RECOVERY_PADDING in order to
compensate for packets we might have missed during
recovery.
It seems that some GEM APs have issues when the
gap is too big, so use a smaller padding in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We want seq num (freed_pkts) to be initialized
on each new connection, but keep persistent
between recoveries/suspends.
Save the freed_pkts in the private block of the
sta struct (we already do a similar thing for
AP's stations).
However, keep the old wlvif->total_freed_pkts
in order to avoid too intrusive change.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This could be a bit confusing to see warning about lacking support for
5 GHz band if your device supports 2.4 GHz only.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for N-PHY rev 8 with 0x2057 rev 5 is almost ready, but we still
need to figure out how to handle rev 9 first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialization of N-PHY radio revs 5 and 7 requires writing to 0x1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Type of radio has a major meaning for the driver. There is quite some
code that does initialization/calibration depending on the radio rev.
Knowing radio params is quite important to provide help to users, so
print it even with debugging disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ERTM support is disabled, then do not even send ERTM configuration
option even if the remote side supports it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the white list is in use the code would not update the
HCI_CONNECTABLE flag if it gets changed through the ioctl code (e.g.
hciconfig hci0 pscan). Since the flag is important for properly
accepting incoming connections add code to fix it up if necessary and
emit a New Settings mgmt event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for looking up entries in the white list when
HCI_CONNECTABLE is not set. The logic is fairly simple: if we're
connectable check the black list, if we're not connectable check the
white list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Page scan should be enabled either if the connectable setting is set or
if there are any entries in the BR/EDR white list. This patch implements
such behavior by updating the two places that were making decisions on
whether to enable page scan or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The conditions for accepting an incoming connections are already
non-trivial and will become more so once a white list is added. This
patch breaks up the checks for when to reject the request by creating a
helper function for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since page scan might be enabled by Add Device we should not implicitly
set connectable whenever something else than Set Connectable changes it.
This patch makes sure that we don't set HCI_CONNECTABLE for these cases
if there are any entries in the white list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're removing the last item in the white list or adding the first
one to it and HCI_CONNECTABLE is not set we need to update the current
page scan. This patch adds a simple helper function for the purpose and
calls it from the respective mgmt command handlers.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch extends the Add/Remove device commands by letting user space
pass BR/EDR addresses to them. The resulting entries get stored in a new
hdev->whitelist list. The idea is that we can now selectively accept
connections from devices in the list even though HCI_CONNECTABLE is not
set (the actual implementation of this is coming in a subsequent patch).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We already have several lists with struct bdaddr_list entries, and there
will be more in the future. Since the operations for adding, removing,
looking up and clearing entries in these lists are exactly the same it
doesn't make sense to define new functions for every single list. This
patch unifies the functions by passing the list_head to them instead of
a hci_dev pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Authenticated Payload Timeout Expired event is valid for
controllers with BR/EDR Secure Connections support, but also for
LE only controllers supporting LE Ping feature. When either of them
is available enable this event. Previous it was not enabled when
the controller was only supporting LE operation.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All LE controllers always implicitly stop advertising when establishing
connections. Therefore, be sure to clear the flag in the event handler
for new LE connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the connectable state change doesn't require any special HCI commands
the set_connectable_update_settings() function is used instead of the
set_connectable_complete() function. We must therefore make sure to call
hci_update_background_scan() there as well. This code path is used also
when we're powered off, but that's fine since hci_update_background_scan()
has the necessary checks for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The connectable and discoverable mgmt settings are supported both for LE
and BR/EDR controllers so they do not belong behind a lmp_bredr_capable()
condition. This patch fixes the issue in get_supported_settings().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If any of the HCI commands from the hci_stop_discovery function were
successfully sent we need to set the discovery state to STOPPING. The
Stop Discovery code was already handling this, but the code in
clean_up_hci_state was not. This patch updates the hci_stop_discovery to
return a bool to indicate whether it queued any commands and the
clean_up_hci_state() function respectively to look at the return value
and call hci_discovery_set_state() if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are many different places that can disable LE scanning but we only
want to re-enable advertising in hci_cc_le_set_scan_enable() for a very
specific use case, which is when the active scanning part of Start
Discovery is complete. Because of this, fix the discovery state check to
test for the exact state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Many controllers allow simultaneous active scanning and advertising
(e.g. Intel and Broadcom) but some do not (e.g. CSR). It's therefore
safest to implement mutual exclusion of these states in the kernel.
This patch ensures that the two states are never entered simultaneously.
Extra precaution needs to be taken for outgoing connection attempts in
slave role (i.e. through directed advertising) in which case the
operation that came first has precedence and the one that comes after
gets a rejection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Most controllers do not support advertising while initiating an LE
connection. We also have to first disable current advertising if the
initiation is going to happen through direct advertising. Therefore,
simply stop advertising as the first thing when starting to issue
commands to establish an LE connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When deciding to call disable_advertising() we're interested in the real
state instead of the mgmt setting. Use therefore HCI_LE_ADV instead of
the HCI_ADVERTISING flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By adding support for disabling advertising when necessary and doing the
checks for existing LE connections inside the enable_advertising
function we can simplify the calling code quite a lot.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that we have a flag for tracking the real advertising state we
should use that to determine whether it's safe to update the random
address or not. The couple of places that were clearing the flag due to
a pending request need to be updated too.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
