Add i2c bindings for the mcp230xx devices. This is quite a lot simpler
than the spi one as there's no funky sub addressing done (one struct
i2c_client per struct gpio_chip).
The mcp23s08_platform_data structure is reused for i2c, even though
only a single mcp23s08_chip_info structure is needed.
To use, simply fill out a platform_data structure and pass it in
i2c_board_info, E.G.:
static const struct mcp23s08_platform_data mcp23017_data = {
.chip[0] = {
.pullups = 0x00ff,
},
.base = 240,
};
static struct i2c_board_info __initdata i2c_devs[] = {
{ I2C_BOARD_INFO("mcp23017", 0x20),
.platform_data = &smartview_mcp23017_data, },
...
};
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Change spi member of struct mcp23s08 to be a ops-specific opaque data
pointer, and move spi specific knowledge out of mcp23s08_probe_one().
No functional change, but is needed to add i2c support.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There's no in-tree users, and bus notifiers are more generic anyway.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch adds device tree probe support for gpio-mxc driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes
platform_device_id to distinguish the different gpio types, IMX1_GPIO
on i.mx1, IMX21_GPIO on i.mx21 and i.mx27, IMX31_GPIO on all other
i.mx SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The wrong bit was masked when acking langwell gpio interrupts.
Reason for maskig the wrong bit was probably because__ffs() and ffs() functions
return bit indexes differently (0..31 vs 1..32)
This fixes langwell based devices from hanging when a gpio interrupt is
triggered and undoes the breakage which occurred in change set
732063b92b
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The bgpio_init() function does not initialise the shadow register for
the GPIO direction register. Thus, when configuring the first GPIO with
gpio_set_direction() all other GPIOs of the same bank will be
configured as inputs. Since the bgpio layer cannot know whether the
register is readable, the initialisation should be done by the caller
of bgpio_init().
Also, the 'data' shadow variable that is used inside basic_mmio_gpio
to cache the current value of the GPIO_DR register is initialised from
the GPIO_PSR register within bgpio_init(). Thus when setting the
output value of a certain GPIO, the other GPIO outputs of the same
bank will be set or cleared depending on the pin state of the GPIO
inputs during bgpio_init().
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting consolidated into drivers/gpio. While at it,
change the driver name to mpc5200-gpio* to avoid collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
DA9052 PMIC has 16 bit GPIO bus for peripheral control.
This patch add support for the GPIO pins on the DA9052.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Engineering names are more stable than marketing names. Hence, use them
for Device Tree compatible properties instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
with the "for (; i != 0; i--)" sytax, i-- will be executed after the iteration.
thus dev_err shows wrong i value.
Switch to "while(--i >= 0)" which is better in readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The property 'polarity' is handled by the GPIO core, and the 'gpio-base'
should be assigned automatically. It is meaningless in the device-tree,
since GPIO's are identified by the "chip-name"/offset pair.
This way, the whole pca953x_get_alt_pdata() can hopefully soon go away.
We still need to check whether we really want GPIO-interrupt functionality
by simply looking if the I2C node has an interrupts property defined, since
this property is not used for anything else.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In the case that we obtain device-tree data to fill in platform_data, the new
platform data struct was dynamically allocated, but the pointer to it was not
used everywhere it should. It seems easier to fix this issue by removing the
dynamic allocation altogether since its data is only used during driver
probing.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It seems that in the normal case, IRQ_NOREQUEST needs to be explicitly
cleared, otherwise claiming the interrupt fails.
In the case of sparse interrupts, the descriptor needs to be allocated
first.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove cpu_is_* checks from gpio_show_revision() by passing in the
revision address offset from platform data. SoCs with no revision
register (15xx, 7xx, and all MPUIOs) use -1 (actually, USHRT_MAX) to
signify no register.
While here, all GPIO banks are assumed to be the same revision, so fix
show_revision() to only show the revision for the first bank it finds.
This removes duplicate GPIO revision prints during boot.
Thanks to Charulatha V <charu@ti.com> for finding/fixing a few -1s
that were missed in the original patch.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Make _set_gpio_wakeup() generic by removing ifdefs. Code for the
various SoCs/bank-methods was already the same, except for the
non-wakeup GPIO checking. But that flag is set on a per-SoC basis, so
can be used for all SoCs.
While here, use dev_err() and remove GPIO bank calculation assumption
based on subtracting bank pointers.
Signed-off-by: Kevin Hilman <khilman@ti.com>
These functions are useless. They are only called in a few places,
and where they are called, the GPIO has already been converted from an
IRQ or masked, so these functions will never fail.
Signed-off-by: Kevin Hilman <khilman@ti.com>
MPUIO banks have their own dedicated IRQ chip interface, separate from
the "normal" GPIO banks. Convert the MPUIO IRQ chip over to using
the new generic IRQ chip interface.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup GPIO IRQ enable/disable handling by removing SoC-specific
Also split enable/disable IRQ into separate functions for better
readability and also facilitate potentially moving to generic irq_chip
in the future.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup IRQ status handling by passing IRQ status register offsets
via platform data.
Cleans up clearing of GPIO IRQ status and GPIO ISR handler.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add register offset fields to GPIO platform_data for registers.
This patch adds registers that control direction, input and output
data. Using these register offsets in the common driver allows
removal of #ifdefs and greatly improves readability.
Also create dedicated data out functions: one for banks with dedicated
set/clear registers, and another for banks with a single mask
register.
Signed-off-by: Kevin Hilman <khilman@ti.com>
The get_gpio_index() function, littered with cpu_is_* checks can be easily
replaced by using bitops based on the GPIO bank width. Do so.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Rather than having a file-global bank_width variable, move it into
struct gpio_bank so it can be bank-specific. Note the bank width
is already passed per-bank via platform_data, so current code would
be incorrect if any banks had different width.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the OMAP1 #ifdef and MPUIO special case for _clear_gpio_irqbank()
The MPUIOs do not need a register access to ack/clear the IRQ status,
since reading the IRQ status clears it. In addition, the MPUIO
irq_chip has an empty ack method, so _clear_gpio_irqbank() is never
used for MPUIOs.
Signed-off-by: Kevin Hilman <khilman@ti.com>
In commit 78a1a6d341 (ARM: OMAP4: Update
the GPIO support) braces were mistakenly added to included the
register read-back inside the cpu_is_* checking.
Remove the braces, ensuring that a register read-back is done, even
when the IRQSTATUS2 register is not written.
Note that the register read-back might be IRQSTATUS1 or IRQSTATUS2
depending on the CPU, but a read-back of any register in that region
will cause a flush of the posted writes.
Signed-off-by: Kevin Hilman <khilman@ti.com>
If gpio pins from bank[2-5] are marked as wakeup enable and if the wake is
through gpio IO pad wakeup, then that wakeup gpio interrupt is lost.
In the current implementation, GPIO driver stores the context of DATAIN of
all the gpio in the bank. During GPIO resuming, it checks DATAIN with wakeup
enabled pins of gpio bank. If there is status change, then manually toggle
GPIO_LEVELDETECT to generate pseudo interrupt.
Reported-by: Philippe Mazet <p-mazet@ti.com>
Tested-by: Philippe Mazet <p-mazet@ti.com>
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
As part of the gpio driver consolidation, this patch moves the Tegra driver
into drivers/gpio
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
The 74x164 GPIO driver has a static inline helper called
gpio_to_chip which clashes with the gpiolib namespace if we
try to expose the function with the same name from gpiolib,
and it's still confusing even if we don't do that. So rename
it to gpio_to_74x164_chip().
Reported-by: H Hartley Sweeten <hartleys@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When calling gpio_get_value, the gpio number other than bit offset
should be passed as the argument.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove miscellaneous use of direct calculation by using resource_size().
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This converts the gpio-ep93xx driver into a platform_driver and uses
the basic_mmio_gpio library.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When using nested threaded irqs, use handle_nested_irq(). This function
does not call the chip handler, so no handler is set.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The interrupt pin of the PCA953x is active low, and on the rising edge
no interrupt should be produced.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It seems that in the normal case, IRQ_NOREQUEST needs to be explicitly
cleared, otherwise claiming the interrupt fails.
In the case of sparse interrupts, the descriptor needs to be allocated
first.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With this driver now being moved from arch/arm/mach-ep93xx/gpio.c to
drivers/gpio/gpio-ep93xx.c the prefix "ep93xx" is now redundant in the
pr_* output. Using KBUILD_MODNAME is sufficient.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The S3C_GPIO_PULL_UP macro value incorrectly maps to a reserved setting of GPIO
pull up/down registers on Exynos4 platform. Fix this incorrect mapping by adding
wrappers to the s3c_gpio_setpull_updown and s3c_gpio_getpull_updown functions.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch converts gpio-mxs driver to use generic irq chip.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The irq_high stuff was mistakenly copied from mxc gpio driver.
The mxs gpio controller has only one irq line for each 32-pin
gpio port. The patch remove irq_high related codes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The gpio-mxs controller complies with basic_mmio_gpio library. This
patch converts the driver to use the library.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
_set_gpio_triggering uses read-modify-write on bank registers,
lock bank->lock around all calls to it to prevent register
corruption if two cpus access gpios in the same bank at the
same time.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setting the IRQWAKEN bit was overwriting previous IRQWAKEN bits,
causing only the last bit set to take effect, resulting in lost
wakeups when the GPIO controller is in idle.
Replace direct writes to IRQWAKEN with MOD_REG_BIT calls to
perform a read-modify-write on the register.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
WARNING: arch/arm/plat-omap/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function omap_gpio_probe() to the function .init.text:omap_gpio_chip_init()
The function __devinit omap_gpio_probe() references
a function __init omap_gpio_chip_init().
If omap_gpio_chip_init is only used by omap_gpio_probe then
annotate omap_gpio_chip_init with a matching annotation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Sort the gpio makefile and enforce the naming convention gpio-*.c for
gpio drivers.
v2: cleaned up filenames in Kconfig and comment blocks
v3: fixup use of BASIC_MMIO to GENERIC_GPIO for mxc
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The interrupt pin of the PCA953x is active low, and on the rising edge
no interrupt should be produced.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The GPIO driver should reside in drivers/gpio.
v3: Change Kconfig option to def_bool y
v2: Make the Kconfig symbol a silent option, dependent on ARCH_EP93XX
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The gpio-mxc controller complies with basic_mmio_gpio library. The
patch convert the driver to use the library.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.
* Add a list to save all mx2 ports references, so that
mx2_gpio_irq_handler can walk through all interrupt status
registers
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxc_gpio_init into mxc_gpio_probe function
* Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
be public at all, and also make some other cleanup on
plat-mxc/include/mach/gpio.h at the same time
And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation. This patch moves the plat-mxc driver. Follow up
patches will clean it up and make it a fine upstanding gpio driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch makes necessary changes on gpio-mxs as below to turn it
into an upstanding gpio driver.
* Clean up the gpio port definition stuff
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxs_gpio_init into mxs_gpio_probe function
And it then migrates mach-mxs to the updated driver by adding
corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation. This patch moves the mxs driver. Follow up patches
will clean it up and make it a fine upstanding example of a gpio
driver.
v2: Removed header file entirely and put struct definition directly
into driver. The struct isn't used anywhere else in the kernel.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove the #define GEN_74X164_GPIO_COUNT since it's only used in
one place and it's meaning is obvious. Also remove the #define
GEN_74X164_DRIVER_NAME and use spi->modalias to set the gpio chip's
label and the string "74x164" for the driver name.
Reorder the code slightly to remove the need to prototype
gen_74x164_set_value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
After the GPIO driver move, some symbols became selectable when they
shouldn't be. Tighten the dependencies.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We had a few drivers move from arch/arm into drivers/gpio, but they
don't actually compile without the ARM platform headers etc. As a
result they were messing up allyesconfig on x86.
Make them depend on ARM.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/pch_gpio: Support new device ML7223
gpio: make gpio_{request,free}_array gpio array parameter const
GPIO: OMAP: move to drivers/gpio
GPIO: OMAP: move register offset defines into <plat/gpio.h>
gpio: Convert gpio_is_valid to return bool
gpio: Move the s5pc100 GPIO to drivers/gpio
gpio: Move the s5pv210 GPIO to drivers/gpio
gpio: Move the exynos4 GPIO to drivers/gpio
gpio: Move to Samsung common GPIO library to drivers/gpio
gpio/nomadik: add function to read GPIO pull down status
gpio/nomadik: show all pins in debug
gpio: move Nomadik GPIO driver to drivers/gpio
gpio: move U300 GPIO driver to drivers/gpio
langwell_gpio: add runtime pm support
gpio/pca953x: Add support for pca9574 and pca9575 devices
gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
gpio_{request,free}_array should not (and do not) modify the passed gpio
array, so make the parameter const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO 1 to 8 are added for TPS65911 chip version. The gpio driver
now handles more than one gpio lines. Subsequent versions of the
chip family can add new GPIO lines with minimal driver changes.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The GPIO driver should reside in drivers/gpio/ for better
organization.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Move the Samsung s5pc100 SoC GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move the Samsung s5pv210 SoC GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move the Samsung Exynos4 series SoCs GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It's common gpiolib for recent Samsung SoCs. Move to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Useful to check the status of the runtime pin muxing.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Squashed, modified to use chip-internal IRQ trigger state]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This moves the Nomadik GPIO driver out of arch/arm/plat-nomadik
and into the desired location indicated by the subsystem
maintainer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[grant.likely: squashed with kconfig fixup]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This moves the U300 GPIO driver out of arch/arm/mach-u300 and into
the desired location indicated by the subsystem maintainer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While this is essentially a no-op for this driver, it has the
side effect of letting the PMU driver snoop D3 requests from
the PCI core for this driver.
This is only for langwell, not for whitney point.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
PCA957x is i2c gpio expander, and similar to PCA953x. Although register
configurations are different between PCA957x and PCA953x. They can share
a lot of components, such as IRQ handling, GPIO IN/OUT. So updating PCA953x
driver to support PCA957x chips.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
cs5535-gpio.c has been split into two, with various setup moved
into cs5535-mfd.c. Given that cs5535-gpio will not load without
the -mfd part, lets make that dependency explicit in Kconfig
Signed-off-by: Ed Wildgoose <kernel@wildgooses.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/via: rename VIA local config struct
basic_mmio_gpio: split into a gpio library and platform device
gpio: remove some legacy comments in build files
gpio: add trace events for setting direction and value
gpio/pca953x: Use handle_simple_irq instead of handle_edge_irq
gpiolib: export gpiochip_find
gpio: remove redundant Kconfig depends on GPIOLIB
basic_mmio_gpio: convert to non-__raw* accessors
basic_mmio_gpio: support direction registers
basic_mmio_gpio: support different input/output registers
basic_mmio_gpio: detect output method at probe time
basic_mmio_gpio: request register regions
basic_mmio_gpio: allow overriding number of gpio
basic_mmio_gpio: convert to platform_{get,set}_drvdata()
basic_mmio_gpio: remove runtime width/endianness evaluation
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
alpha allmodconfig:
drivers/gpio/ml_ioh_gpio.c: In function 'ioh_gpio_probe':
drivers/gpio/ml_ioh_gpio.c:205: error: implicit declaration of function 'kzalloc'
drivers/gpio/ml_ioh_gpio.c:205: warning: assignment makes pointer from integer without a cast
also fix this:
drivers/gpio/ml_ioh_gpio.c:145: warning: 'ioh_gpio_save_reg_conf' defined but not used
drivers/gpio/ml_ioh_gpio.c:154: warning: 'ioh_gpio_restore_reg_conf' defined but not used
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha allmodconfig:
drivers/gpio/vx855_gpio.c: In function 'vx855gpio_probe':
drivers/gpio/vx855_gpio.c:233: error: implicit declaration of function 'kzalloc'
drivers/gpio/vx855_gpio.c:233: warning: assignment makes pointer from integer without a cast
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow GPIO_BASIC_MMIO_CORE to be used to provide an accessor library
for implementing GPIO drivers whilst abstracting the register access
detail. Based on a patch from Anton Vorontsov[1] and adapted to allow
bgpio_chip to be embedded in another structure.
Changes since v1:
- Register the gpio_chip in the platform device probe
1. https://lkml.org/lkml/2011/4/19/401
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The build files for drivers/gpio has some wording and comments
about the directory being reserved exclusively for GPIO expanders
(according to the gpio.txt file these are on external busses) and
this has been false for some time. We already have PL061 and
Xilinx drivers which are in silicon and now I'm moving more
silicon drivers here, so delete this and reword it a bit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch allows to trace gpio operations using ftrace
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make pca953x driver use the simple irq handler since no hardware control
is necessary and the driver lacks an irq_ack function. handle_edge_irq()
calls chip->irq_ack() which crashes since this function does not exist.
Signed-off-by: Erik Botö <erik.boto@pelagicore.com>
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Export function gpiochip_find so that modules can use it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since all the drivers are in a 'if GPIOLIB/endif block', the depends on GPIOLIB
is redundant so remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The __raw_* accessors don't include memory barriers and can cause
problems when writes get stuck in write buffers.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Most controllers require the direction of a GPIO to be set by writing to
a direction register. Add support for either an input direction
register or an output direction register.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some controllers have separate input and output registers. For these
controllers, use "set" for the output and "dat" for the input.
Changes since v2: reuse "set" for output and "dat" for input rather than
adding a new "in" register.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Rather than detecting the output method each time in the .set()
callback, do it at probe time and set the appropriate callback.
Changes since v2: moved the reg_dat initialization into
bgpio_setup_io().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make sure that we get the register regions with request_mem_region()
before ioremap() to make sure we have exclusive access.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some platforms may have a number of GPIO that is less than the register
width of the peripheral.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the platform drvdata helpers rather than working on the struct
device itself.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove endianness/width calculations at runtime by installing function
pointers for bit-to-mask conversion and register accessors.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
dt/fsldma: fix build warning caused by of_platform_device changes
spi: Fix race condition in stop_queue()
gpio/pch_gpio: Fix output value of pch_gpio_direction_output()
gpio/ml_ioh_gpio: Fix output value of ioh_gpio_direction_output()
gpio/pca953x: fix error handling path in probe() call
The pch_gpio_direction_output() function was missing a write to set the
desired output value. The function would properly set the GPIO
direction, but not the output value. The value would have to manually
be set with a follow up call to pch_gpio_set().
Add the missing write so that pch_gpio_direction_output() sets both the
GPIO direction and value.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The ioh_gpio_direction_output() function was missing a write to set the
desired output value. The function would properly set the GPIO
direction, but not the output value. The value would have to manually
be set with a follow up call to ioh_gpio_set().
Add the missing write so that ioh_gpio_direction_output() sets both the
GPIO direction and value.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If the device fails to respond, then the error path tries to remove an
interrupt that never got registered, which causes an backtrace from the
interrupt handling code.
Fix this by ensuring that the cleanup path has two labels and use the
correct path as needed.
fixes the following error:
WARNING: at kernel/irq/manage.c:908 __free_irq+0x80/0x160()
Trying to free already-free IRQ 0
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver is broken in several aspects.
1) old style irq_chip functions. Sigh
2) Abuse of the unlock callback. That's not supposed to be a state
machine for evrything and some more.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To get rid of port expanders, the free GPIOs of ab8500
can be used. There are 42 GPIO pins. Out of which 16
are interrupt capable.This patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[Renamed header file as per MFD structure]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212509.118888535@linutronix.de>
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212509.025730689@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gpiolib plus two gpio implementations in arm fiddle in the guts of
irq_desc in a racy and buggy way. Remove the stuff. I already told the
gpio folks that we can provide that information in a proper way if
necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212508.931638262@linutronix.de>
Almost the same driver for both Poulsbo and Tunnel Creek.
The difference is in quantity of GPIOs powered by the core power
rail and by suspend power supply, default values for some GPIOs, etc.
Detect actual hardware by platform device ID assigned in lpc_sch
and set configuration accordingly.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use mfd_data for passing information from mfd drivers to soc
clients. The mfd_cell's driver_data field is being phased out.
Clients that were using driver_data now access .mfd_data
via mfd_get_data().
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/dw_spi: move dw_spi.h into drivers/spi
spi/dw_spi: Fix missing header
gpio/langwell: Clear edge bit before handling
gpio/langwell: Simplify demux loop
gpio/langwell: Convert irq name space
gpio/langwell: Fix broken irq_eoi change.
gpio; Make Intel chipset gpio drivers depend on x86
gpio/cs5535-gpio: Fix section mismatch
spi/rtc-{ds1390,ds3234,m41t94}: Use spi_get_drvdata() for SPI devices
spi/davinci: Support DMA transfers larger than 65535 words
spi/davinci: Use correct length parameter to dma_map_single calls
gpio: Use __devexit at necessary places
gpio: add MODULE_DEVICE_TABLE to pch_gpio and ml_ioh_gpio
gpio/mcp23s08: support mcp23s17 variant
of_mmc_spi: add card detect irq support
spi/omap_mcspi: catch xfers of non-multiple SPI word size
spi/omap_mcspi: Off-by-one error in finding the right divisor
gpio/pca953x: Fix wrong pointer type
spi/pl022: rid dangling labels
spi: add support for SuperH SPI
...
I don't have the specs for this beast, but it looks a lot like the PXA
GPIO block. Though I bet it's the same IP and the driver should have
reused the PXA code.
Acknowleding the edge detect status after handling one or more gpio
interrupts looks wrong. We might lose an edge which came in while we
handled the previous one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alek Du <alek.du@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
Use __ffs() to find the pending interrupt source instead of looping 32
times.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert to the new irq function names.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 0766d20fd (langwell_gpio: modify EOI handling following change
of kernel irq subsystem) changes
- desc->chip->eoi(irq);
+
+ if (desc->chip->irq_eoi)
+ desc->chip->irq_eoi(irq_get_irq_data(irq));
+ else
+ dev_warn(pg->chip.dev, "missing EOI handler for irq %d\n", irq);
With the following explanation:
"Latest kernel has many changes in IRQ subsystem and its interfaces,
like adding irq_eoi" for struct irq_chip, this patch will make it
support both the new and old interface."
This is completely bogus.
#1) The changelog does not match the patch at all
#2) This driver relies on the assumption that it sits behind an eoi
capable interrupt line. If the implementation of the underlying
chip changes from eoi to irq_eoi then this driver has to follow
that change and not add a total bogosity.
#3) Just mechanically changing eoi to irq_eoi without checking the
background of that change is sloppy at best.
Remove the sillyness and retrieve the interrupt data from irq_desc
directly. No need to go through a sparse irq lookup.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Nothing outside of x86 can use that code.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix section mismatch by annotating using variable name suffix.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entries will be added to
modules.pcimap:
pch_gpio 0x00008086 0x00008803 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
ml_ioh_gpio 0x000010db 0x0000802e 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function gen_74x164_remove and mc33880_remove are used only wrapped
by __devexit_p so define it using __devexit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entries will be added to modules.pcimap:
pch_gpio 0x00008086 0x00008803 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
ml_ioh_gpio 0x000010db 0x0000802e 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
mpc23s17 is very similar to the mcp23s08, except that registers are 16bit
wide, so extend the interface to work with both variants.
The s17 variant also has an additional address pin, so adjust platform
data structure to support up to 8 devices per SPI chipselect.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
pca953x_get_alt_pdata() uses uint16_t* as result type for
of_get_property(), but numeric of values are __be32.
Checking for negative values is bogus because of-property
values are unsigned by definition.
Instead check for proper property size.
v3: - assume big-endian properties
- check property size
v2: - removed bogus check for negative property values
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq_chip->irq_mask/unmask are called with interrupts disabled and
irq_desc->lock held. So we cannot access i2c from this context. That's
what irq_bus_sync_unlock() is for.
Store the masked information in the chip data structure and update the
i2c bus from the irq_bus_sync_unlock() callback.
This does not need a while(pending) loop because the update to this is
always serialized via the bus lock, so we never have more than one pin
update pending.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Gregory Bean <gbean@codeaurora.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a mutex to register communication and handling. Without the mutex,
GPIOs didn't switch as expected when toggled in a fast sequence of
status changes of multiple outputs.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Latest kernel has many changes in IRQ subsystem and its interfaces, like
adding "irq_eoi" for struct irq_chip, this patch is a follow up change
for that.
Also remove the unnecessary cast for a "void *".
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
mfd: ab8500-core chip version cut 2.0 support
mfd: Flag WM831x /IRQ as a wake source
mfd: Convert WM831x away from legacy I2C PM operations
regulator: Support MAX8998/LP3974 DVS-GPIO
mfd: Support LP3974 RTC
i2c: Convert SCx200 driver from using raw PCI to platform device
x86: OLPC: convert olpc-xo1 driver from pci device to platform device
mfd: MAX8998/LP3974 hibernation support
mfd/ab8500: remove spi support
mfd: Remove ARCH_U8500 dependency from AB8500
misc: Make AB8500_PWM driver depend on U8500 due to PWM breakage
mfd: Add __devexit annotation for vx855_remove
mfd: twl6030 irq_data conversion.
gpio: Fix cs5535 printk warnings
misc: Fix cs5535 printk warnings
mfd: Convert Wolfson MFD drivers to use irq_data accessor function
mfd: Convert TWL4030 to new irq_ APIs
mfd: Convert tps6586x driver to new irq_ API
mfd: Convert tc6393xb driver to new irq_ APIs
mfd: Convert t7166xb driver to new irq_ API
...
Commit a1f5f22adc ("gpio: timbgpio:
irq_data conversion") was slightly too enthusiastic in converting
timbgpio_irq() over to take an irq_data * argument instead of an
unsigned int irq argument, as it is a flow handler, which still take
IRQ numbers for now. (And on top of that, it was using the wrong
accessors.)
This fixes it up, and seems to build without warnings.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/gpio/cs5535-gpio.c: In function 'cs5535_gpio_probe':
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Use vsprintf extension %pR to format resource.
Original-patch-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds MODULE_ALIAS entries to the various cs5535 subdevice modules; this
allows the modules to automatically be loaded when cs5535-mfd loads.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cs5535-mfd driver now takes care of the PCI BAR handling; this
simplifies the gpio driver a lot.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ML7213 is a companion chip for Intel Atom E6xx series. This driver can be
used for OKI SEMICONDUCTOR ML7213 IOH(Input/Output Hub) which is for
IVI(In-Vehicle Infotainment) use. This driver can access the IOH's GPIO
device.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Gregory Bean <gbean@codeaurora.org>
Tested-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Yin Kangkai <kangkai.yin@intel.com>
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: "Hennerich, Michael" <Michael.Hennerich@analog.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds (well, re-adds actually) handling for events/IRQs through cs5535
GPIOs. In the wild and wooly world of CS5535, setup_event() is for
assigning an IRQ to a GPIO filter/event pair, and set_irq() sets up the
pair to trigger IRQs.
These should really only be used in highly platform-specific drivers (such
as OLPC's DCON driver). Sadly, because set_irq() uses MSRs, this causes
the driver to become X86-specific.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default for non-READ_BACK GPIO regs is to have the clear bits set;
this means that our original errata fix was too simplistic. This
changes it to the following behavior:
- when setting GPIOs, ignore the higher order bits (they're for
clearing, we don't need to care about them).
- when clearing GPIOs, keep all the bits, but unset (via XOR) the
lower order bit that negates the clear bit that we care about. That
is, if we're clearing GPIO 26 (val = 0x04000000), we first XOR what's
currently in the register with 0x0400 (GPIO 26's SET bit), and then
OR that with the GPIO 26's CLEAR bit.
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The edge detect status GPIOs function differently from the other atomic
model CS5536 GPIO registers; writing 1 to the high bits clears the GPIO,
but writing 1 to the lower bits also clears the bit.
This means that read-modify-write doesn't actually work for it, so don't
apply the errata here. If a negative edge status gets lost after
resume.. well, we tried our best!
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If GPIO request succeeds, but configuration fails, it should be released.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rdc321x-gpio currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Most of the register layout, client IRQ numbers on the TC35892 is shared also
by other variants. Make this generic as tc3589x
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the tc35892 core/gpio drivers to tc3589x to include
new variants in the same mfd core
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the header file to include further variants within
the same mfd core driver
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
The AMD Geode CS5536 Companion Device Silicon Revision B1 Specification
Update mentions the follow as issue #36:
"Atomic write transactions to the atomic GPIO High Bank Feature Bit
registers should only affect the bits selected [...]"
"after Suspend, an atomic write transaction [...] will clear all
non-selected bits of the accessed register."
In other words, writing to the high bank for a single GPIO bit will
clear every other GPIO bit (but only sometimes after a suspend).
The workaround described is obvious and simple; do a read-modify-write.
This patch does that, and documents why we're doing it.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several of the GPIOs on the WM8994 are fixed function on the WM8958 so
error out if the user tries to request them with gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is needed for supporting the upcoming VX855 camera and OLPC DCON
drivers, as well as the advanced viafb features on non-OLPC hardware
based on this chip.
Based on earlier work by Harald Welte.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Free allocated memory. Call stmpe_disable() if it was enabled.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch removes the requirement that gpio base be supplied in
platform data.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
GPIOs on these controller are multi-functional. If you decided to use
some of them e.g. as input channels for the ADC, you surely don't want
those pins to be reassigned as simple GPIOs (which may be triggered even
from userspace via 'export'). Same for the touchscreen controller pins.
Since knowledge about the hardware is needed to decide which GPIOs to
reserve, let this bitmask be inside platform_data and provide some
defines to assist potential users.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In this case the logic is very similar but the IRQs are not exposed and
the device is not picked up via PCI
Based on a separate internal whitney point driver by Yin Kangkai.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Yin Kangkai <kangkai.yin@intel.com>
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Deweird this driver.
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. Topcliff PCH has
GPIO I/F. Using this I/F, it is able to access system devices connected
to GPIO.
[akpm@linux-foundation.org: ese DEFINE_PCI_DEVICE_TABLE (per Joe Perches)]
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tomoya MORINAGA <morinaga526@dsn.okisemi.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement irq_chip functionality on ADP5588/5587 GPIO expanders. Only
level sensitive interrupts are supported. Interrupts provided by this
irq_chip must be requested using request_threaded_irq().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for generic 74x164 serial-in/parallel-out 8-bits shift
register. This driver can be used as a GPIO output expander.
[akpm@linux-foundation.org: remove unused local `refresh']
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Juhos Gabor <juhosg@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some versions of the hardware can trash the IER register if simultaneous
interrupts occur. This patch works around it by using a local copy of the
register and restoring it after every interrupt.
Signed-off-by: Tomas Hallenberg <tomas.hallenberg@pelagicore.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The basic GPIO controllers may be found in various on-board FPGA and ASIC
solutions that are used to control board's switches, LEDs, chip-selects,
Ethernet/USB PHY power, etc.
These controllers may not provide any means of pin setup
(in/out/open drain).
The driver supports:
- 8/16/32/64 bits registers;
- GPIO controllers with clear/set registers;
- GPIO controllers with a single "data" register;
- Big endian bits/GPIOs ordering (mostly used on PowerPC).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Our Moorestown platform has two max7315 chips which is covered by pca953x
i2c gpio driver.
A while ago this driver got updated with nested irq thread support, and it
broke the compatibity with "request_irq". For example, the gpio_keys.c
driver can not work with this driver now. This patch fixes the issue by
switching to generic_handle_irq.
Also fix the irq_base issue: irq_base == 0 is valid, and a "-1" value
should mean invalid. IRQ 0 is not a valid IRQ, irq_base of 0 is valid.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
mtd/m25p80: add support to parse the partitions by OF node
of/irq: of_irq.c needs to include linux/irq.h
of/mips: Cleanup some include directives/files.
of/mips: Add device tree support to MIPS
of/flattree: Eliminate need to provide early_init_dt_scan_chosen_arch
of/device: Rework to use common platform_device_alloc() for allocating devices
of/xsysace: Fix OF probing on little-endian systems
of: use __be32 types for big-endian device tree data
of/irq: remove references to NO_IRQ in drivers/of/platform.c
of/promtree: add package-to-path support to pdt
of/promtree: add of_pdt namespace to pdt code
of/promtree: no longer call prom_ functions directly; use an ops structure
of/promtree: make drivers/of/pdt.c no longer sparc-only
sparc: break out some PROM device-tree building code out into drivers/of
of/sparc: convert various prom_* functions to use phandle
sparc: stop exporting openprom.h header
powerpc, of_serial: Endianness issues setting up the serial ports
of: MTD: Fix OF probing on little-endian systems
of: GPIO: Fix OF probing on little-endian systems
DTB is always big-endian that's why is necessary
to convert it.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For board-specific initialization.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the arbitrary software-reset call from the device-probe
method, because:
- It is defective. To work correctly, it should be two byte writes,
not a single word write. As it stands, it does nothing.
- Some devices with sx150x expanders installed have their NRESET pins
ganged on the same line, so resetting one causes the others to reset -
not a nice thing to do arbitrarily!
- The probe, usually taking place at boot, implies a recent hard-reset,
so a software reset at this point is just a waste of energy anyway.
Therefore, make it optional, defaulting to off, as this will match the
common case of probing at powerup and also matches the current broken
no-op behavior.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The debounce times are approximate, they can be selected using the two
input functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the GPIOs on STMPE I/O Expanders.
[l.fu@pengutronix.de: fix set direction input]
[l.fu@pengutronix.de: set GPIO alternate function while requesting]
Acked-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The pca953x driver requires the use of threaded irqs as its irq
demultiplexer can sleep. Our irq handler can be called from any context,
so use request_any_context_irq to allow threaded irqs as well.
Signed-off-by: Daniel Gl?ckner <dg@emlix.com>
Reported-by: Ian Jeffray <ian@jeffray.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As sysfs_notify_dirent has been made irq safe, there is no reason to not
call it directly from irq. With the work_struct removed, the remaining
element in poll_desc is a sysfs_dirent pointer which may not be NULL. We
can therefore store it directly in the idr and pass it as context to the
irq handler.
Most part of the patch deals with renaming defines and variables to
reflect their new use without functional change.
I also took the opportunity to initialize the idr statically.
Signed-off-by: Daniel Gl?ckner <dg@emlix.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Be more consistent about runtime programming interface abuse warnings,
which can reduce some confusion and trigger bugfixes. Based on an
observation and patch from Jani Nikula.
Also update doc to highlight some sleeping-call issues and to match some
recent changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: "Ryan Mallon" <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide sane defaults for pcf857x, so the driver can be used w/o providing
platform data (and thus can be simply bound via OF tree).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gpios on the max730x chips have support for internal pullups while in
input mode.
This patch adds support for configuring these pullups via platform data.
A new member ("input_pullup_active") to the platform data struct is
introduced. A set bit in this variable activates the pullups while the
respective port is in input mode. This is a compatible enhancement since
unset bits lead to disables pullups which was the default in the original
driver.
_Note_: the 4 lowest bits in "input_pullup_active" are unused because the
first 4 ports of the controller are not used, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
When freeing a gpio that has not been exported, gpio_unexport() prints a
debug message when it should just fall through silently.
Example spurious message:
gpio_unexport: gpio0 status -22
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
Cc: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found in the Versatile build:
WARNING: drivers/built-in.o(.data+0x14c): Section mismatch in reference from the variable pl061_gpio_driver to the (unknown reference) .init.data:(unknown)
The variable pl061_gpio_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x40f8): Section mismatch in reference from the variable pl011_driver to the (unknown reference) .init.data:(unknown)
The variable pl011_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x5ab4): Section mismatch in reference from the variable pl031_driver to the (unknown reference) .init.data:(unknown)
The variable pl031_driver references
the (unknown reference) __initdata (unknown)
Basically, amba_id structures must not be __initdata. Also fix:
WARNING: drivers/built-in.o(.data+0x138): Section mismatch in reference from the variable pl061_gpio_driver to the function .init.text:pl061_probe()
The variable pl061_gpio_driver references
the function __init pl061_probe()
which is an incorrectly annotated probe function. Fix it to reflect
the other AMBA bus probe functions by removing the __init attributation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
My Collabora address is no longer enabled - update the MODULE_AUTHOR
fields of drivers to my current email address.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement generic OF gpio hooks and thus make device-enabled GPIO chips
(i.e. the ones that have gpio_chip->dev specified) automatically attach
to the OpenFirmware subsystem. Which means that now we can handle I2C and
SPI GPIO chips almost* transparently.
* "Almost" because some chips still require platform data, and for these
chips OF-glue is still needed, though with this change the glue will
be much smaller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
CC: linux-kernel@vger.kernel.org
CC: devicetree-discuss@lists.ozlabs.org
Currently the kernel uses the struct device_node.data pointer to resolve
a struct gpio_chip pointer from a device tree node. However, the .data
member doesn't provide any type checking and there aren't any rules
enforced on what it should be used for. There's no guarantee that the
data stored in it actually points to an gpio_chip pointer.
Instead of relying on the .data pointer, this patch modifies the code
to add a lookup function which scans through the registered gpio_chips
and returns the gpio_chip that has a pointer to the specified
device_node.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Anton Vorontsov <avorontsov@ru.mvista.com>
CC: Grant Likely <grant.likely@secretlab.ca>
CC: David Brownell <dbrownell@users.sourceforge.net>
CC: Bill Gatliff <bgat@billgatliff.com>
CC: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Jean Delvare <khali@linux-fr.org>
CC: linux-kernel@vger.kernel.org
CC: devicetree-discuss@lists.ozlabs.org
The OF gpio infrastructure is great for describing GPIO connections within
the device tree. However, using a GPIO binding still requires changes to
the gpio controller just to add an of_gpio structure. In most cases, the
gpio controller doesn't actually need any special support and the simple
OF gpio mapping function is more than sufficient. Additional, the current
scheme of using of_gpio_chip requires a convoluted scheme to maintain
1:1 mappings between of_gpio_chip and gpio_chip instances.
If the struct of_gpio_chip data members were moved into struct gpio_chip,
then it would simplify the processing of OF gpio bindings, and it would
make it trivial to use device tree OF connections on existing gpiolib
controller drivers.
This patch eliminates the of_gpio_chip structure and moves the relevant
fields into struct gpio_chip (conditional on CONFIG_OF_GPIO). This move
simplifies the existing code and prepares for adding automatic device tree
support to existing drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Hopefully it makes the code look nicer and makes it easier to extend
this function.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: devicetree-discuss@lists.ozlabs.org
CC: linux-kernel@vger.kernel.org
Update Kconfig and Makefile in drivers/gpio to discourage inappropriate
addition of platform-specific code.
[akpm@linux-foundation.org: fix tpyo]
Signed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rdc_gpio_set_value_impl has the gpio data registers 1 and 2 inverted, fix this.
Signed-off-by: Bernhard Loos <bernhardloos@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The rdc321x southbridge PCI device has no MEM PCI resources that we could
pass to mfd_add_devices. Since 33254dd5, mfd_add_device checks for the
mem_base argument that we set to NULL. Changing the resources passed to
our MFD cells from IORESOURCE_MEM to IORESOURCE_IO fixes that. Since we use
those resources as offsets to the PCI configuration space base address of
the southbridge device this is also more adequate.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix rdc321x-southbridge build: GPIO_RDC321X needs to select
MFD_CORE so that the core is built at the same (or higher)
tristate level.
rdc321x-southbridge.c:(.devinit.text+0x6103): undefined reference to `mfd_add_devices'
rdc321x-southbridge.c:(.devexit.text+0xe5f): undefined reference to `mfd_remove_devices'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a GPIO driver to support the GPIOs on the TC35892 I/O Expander.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Janz VMOD-TTL is a MODULbus daughterboard which fits onto any MODULbus
carrier board. It essentially consists of some various logic and a Zilog
Z8536 CIO Counter/Timer and Parallel IO Unit.
The board must be physically configured with jumpers to enable a user to
drive output signals. I am only interested in outputs, so I have made this
driver as simple as possible. It only supports a very minimal subset of the
features provided by the Z8536 chip.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a new GPIO driver for the RDC321x SoC GPIO controller.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This eliminates the following build warning:
drivers/gpio/it8761e_gpio.c: In function `it8761e_gpio_exit':
drivers/gpio/it8761e_gpio.c:220: warning: ignoring return value of `gpiochip_remove', declared with attribute warn_unused_result
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel Penwell chip has two 96 pins GPIO blocks, which are very similiar as
Intel Langwell chip GPIO block, except for pin number difference. This
patch expends the original Langwell GPIO driver to support Penwell's.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few architectures, like OMAP, allow you to set a debouncing time for the
gpio before generating the IRQ. Teach gpiolib about that.
Mark said:
: This would be generally useful for embedded systems, especially where
: the interrupt concerned is a wake source. It allows drivers to avoid
: spurious interrupts from noisy sources so if the hardware supports it
: the driver can avoid having to explicitly wait for the signal to become
: stable and software has to cope with fewer events. We've lived without
: it for quite some time, though.
David said:
: I looked at adding debounce support to the generic GPIO calls (and thus
: gpiolib) some time back, but decided against it. I forget why at this
: time (check list archives) but it wasn't because of lack of utility in
: certain contexts.
:
: One thing to watch out for is just how variable the hardware capabilities
: are. Atmel GPIOs have something like a fixed number of 32K clock cycles
: for debounce, twl4030 had something odd, OMAPs were more like the Atmel
: chips but with a different clock. In some cases debouncing had to be
: ganged, not per-GPIO. And so forth.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current message, 'not registered' is confusing as it implies it was
not registered with something, whereas printing 'failed to register'
implies it was the gpiochip_add() call that did not work correctly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug I noticed while hacking on the max732x driver for interrupt
support. According to the datasheets, open-drain pins have to be
configured as output-high (which in that case is actually high impedance)
to be used as input.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setup both client_group_a and client_group_b if nr_port > 8 (not including
nr_port==8).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The valid offset value is 0..PL061_GPIO_NR-1, this patch corrects the
offset value range checking.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpiolib doesn't need to modify the names and I assume most initializers
use string constants that shouldn't be modified anyhow.
[akpm@linux-foundation.org: fix drivers/gpio/cs5535-gpio.c]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the GPIO expanders supported by the max732x driver have interrupt
generation capability by reporting changes on input pins through an INT#
pin. This patch implements the irq_chip functionnality (edge detection
only).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jebediah Huang <jebediah.huang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The problem. When implementing a network namespace I need to be able
to have multiple network devices with the same name. Currently this
is a problem for /sys/class/net/*, /sys/devices/virtual/net/*, and
potentially a few other directories of the form /sys/ ... /net/*.
What this patch does is to add an additional tag field to the
sysfs dirent structure. For directories that should show different
contents depending on the context such as /sys/class/net/, and
/sys/devices/virtual/net/ this tag field is used to specify the
context in which those directories should be visible. Effectively
this is the same as creating multiple distinct directories with
the same name but internally to sysfs the result is nicer.
I am calling the concept of a single directory that looks like multiple
directories all at the same path in the filesystem tagged directories.
For the networking namespace the set of directories whose contents I need
to filter with tags can depend on the presence or absence of hotplug
hardware or which modules are currently loaded. Which means I need
a simple race free way to setup those directories as tagged.
To achieve a reace free design all tagged directories are created
and managed by sysfs itself.
Users of this interface:
- define a type in the sysfs_tag_type enumeration.
- call sysfs_register_ns_types with the type and it's operations
- sysfs_exit_ns when an individual tag is no longer valid
- Implement mount_ns() which returns the ns of the calling process
so we can attach it to a sysfs superblock.
- Implement ktype.namespace() which returns the ns of a syfs kobject.
Everything else is left up to sysfs and the driver layer.
For the network namespace mount_ns and namespace() are essentially
one line functions, and look to remain that.
Tags are currently represented a const void * pointers as that is
both generic, prevides enough information for equality comparisons,
and is trivial to create for current users, as it is just the
existing namespace pointer.
The work needed in sysfs is more extensive. At each directory
or symlink creating I need to check if the directory it is being
created in is a tagged directory and if so generate the appropriate
tag to place on the sysfs_dirent. Likewise at each symlink or
directory removal I need to check if the sysfs directory it is
being removed from is a tagged directory and if so figure out
which tag goes along with the name I am deleting.
Currently only directories which hold kobjects, and
symlinks are supported. There is not enough information
in the current file attribute interfaces to give us anything
to discriminate on which makes it useless, and there are
no potential users which makes it an uninteresting problem
to solve.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SIO chip contains 16 possible gpio lines, not 14. The schematic was
not read carefully.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
spi: spidev_test gives error upon 1-byte transfer
omap2_mcspi: small fixes of output data format
omap2_mcspi: Flush posted writes
spi: spi_device memory should be released instead of device.
spi: release device claimed by bus_find_device_by_name
of: check for IS_ERR()
serial/mpc52xx_uart: Drop outdated comments
gpio: potential null dereference
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6061/1: PL061 GPIO: Bug fix - setting gpio for HIGH_LEVEL interrupt is not working.
ARM: 5957/1: ARM: RealView SD/MMC Card detection and write-protect using GPIOLIB
ARM: 6030/1: KS8695: enable console
ARM: 6060/1: PL061 GPIO: Setting gpio val after changing direction to OUT.
ARM: 6059/1: PL061 GPIO: Changing *_irq_chip_data with *_irq_data for real irqs.
ARM: 6023/1: update bcmring_defconfig to latest version and fix build error
ARM: fix build error in arch/arm/kernel/process.c
In current implementation of PL061, setting type of irq to HIGH_LEVEL is not
working. This patch fixes this bug.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Smatch found a potential null dereference in gpio_setup_irq(). The
"pdesc" variable is allocated with idr_find() that can return NULL. If
gpio_setup_irq() is called with 0 as gpio_flags and "pdesc" is null, it
would OOPs here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Bill Gatliff reported the following bug when using the irq_chip facility
of the pca953x driver on a PPC platform:
BUG: scheduling while atomic: insmod/1530/0x00000002
He traced it back to an i2c transaction in pca953x_irq_set_type(), which
can be called with interrupt disabled (from __setup_irq()). As the i2c
controller can sleep while sending a message, this qualifies as a bad
idea.
This patch moves the i2c transaction to pca953x_irq_bus_sync_unlock(),
where it is actually safe to send an i2c message.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Reported-by: Bill Gatliff <bgat@billgatliff.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pl061_direction_output doesn't set value of gpio to value passed to it.
This patch sets value of GPIO pin to requested value after changing direction
to OUT.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL061 driver is using set_irq_chip_data and get_irq_chip_data for real
irq lines. It must be using *_irq_data functions instead. As chip_data
is used by interrupt controllers also, which makes vic write at incorrect
addresses.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In an error handling case the lock is not unlocked. The return is
converted to a goto, to share the unlock at the end of the function.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E1;
identifier f;
@@
f (...) { <+...
* spin_lock_irqsave (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
According to the header in max730x it is licensed GPLv2.
Add a MODULE_LICENSE to avoid getting the kernel tainted.
[w.sang@pengutronix.de: add MODULE_AUTHOR and MODULE_DESCRIPTION also]
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.
Also drivers can extend the attributes with own data fields
and use that in the low level function.
This makes the class attributes the same as sysdev_class attributes
and plain attributes.
This will allow further cleanups in drivers.
Full tree sweep converting all users.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
LPC_SCH is selected by GPI_SCH and I2C_ISCH, even when PCI is not
enabled, but LPC_SCH depends on PCI, so make GPI_SCH and I2C_ISCH
also depend on PCI.
Those 2 selects also need to select what LPC_SCH selects,
since kconfig does not follow selects.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the chip default but it's possible the bootloader or OTP
will have been configured to a different mode (eg, to provide
feedback during startup).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Revision B of the WM831x devices changes the sense of the tristate
bit for GPIO configuration, inverting it to become an enable instead.
Take account of this in the gpiolib driver.
A current sink regulation status bit has also been added in revision B,
add a flag indicating if it's present but don't use it yet.
This revision also adds an interrupt on key up for the ON pin event
which the existing code is able to take advantage of.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
wm831x_gpio_direction_output() ignored the state passed into it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cs5535-gpio driver's get() function was returning the output value.
This means that the GPIO pins would never work as an input, even if
configured as an input.
The driver should return the READ_BACK value, which is the sensed line
value. To make that work when the direction is 'output', INPUT_ENABLE
needs to be set.
In addition, the driver was not disabling OUTPUT_ENABLE when the direction
is set to 'input'. That would cause the GPIO to continue to drive the pin
if the direction was ever set to output.
This issue was noticed when attempting to use the gpiolib driver to read
an external input. I had previously been using the char/cs5535-gpio
driver.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org> [2.6.33.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the GPIO expanders controlled by the pca953x driver are able to
report changes on the input pins through an *INT pin.
This patch implements the irq_chip functionality (edge detection only).
The driver has been tested on an Arcom Zeus.
[akpm@linux-foundation.org: the compiler does inlining for us nowadays]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce support for triggering interrupts on both rising and falling
edge.
This feature requires version 3 or newer of the IP, a version check is
done when triggering on both edges is requested.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpio_request() without initial configuration of the GPIO is normally
useless, introduce gpio_request_one() together with GPIOF_ flags for
input/output direction and initial output level.
gpio_{request,free}_array() for multiple GPIOs.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the MAX7300-I2C variant of the MAX7301-SPI version. Both chips share
the same core logic, so the generic part of the in-kernel SPI-driver is
refactored into a generic part. The I2C and SPI specific funtions are
then wrapped into seperate drivers picking up the generic part.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename for_each_bit to for_each_set_bit in the kernel source tree. To
permit for_each_clear_bit(), should that ever be added.
The patch includes a macro to map the old for_each_bit() onto the new
for_each_set_bit(). This is a (very) temporary thing to ease the migration.
[akpm@linux-foundation.org: add temporary for_each_bit()]
Suggested-by: Alexey Dobriyan <adobriyan@gmail.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use of get_irq_chip_data() et al. requires including linux/irq.h
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously enabled poll(2) support on one edge was never reconfigured when
sysfs polarity change was triggered from kernel, because 'struct device
*dev' shadowed an earlier definition.
Found by sparse, which I should've run much earlier.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers may use gpiolib sysfs as part of their public user space
interface. The GPIO number and polarity might change from board to
board. The gpio_export_link() call can be used to hide the GPIO number
from user space. Add support for also hiding the GPIO line polarity
changes from user space.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A GPIO driver for the Timberdale FPGA found on the Intel Atom board
Russellville.
The GPIO driver also has an IRQ-chip to support interrupts on the pins.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The wrong test was used, gpio is unsigned and it had an off-by-one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With generic modular drivers handling all of this stuff, the
geode-specific code can go away. The cs5535-gpio, cs5535-mfgpt, and
cs5535-clockevt drivers now handle this.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changed number of gpio pins to 32 (according to datasheet)
Added mask to disable some pins
Added gpio_request for checking mask and disabling special pin functions
Added pin names
[dilinger@collabora.co.uk: make printk usage consistent]
Signed-off-by: Tobias Mueller <Tobias_Mueller@twam.info>
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This creates a CS5535/CS5536 GPIO driver which uses a gpio_chip backend
(allowing GPIO users to use the generic GPIO API if desired) while also
allowing architecture-specific users directly (via the cs5535_gpio_*
functions).
Tested on an OLPC machine. Some Leemotes also use CS5536 (with a mips
cpu), which is why this is in drivers/gpio rather than arch/x86.
Currently, it conflicts with older geode GPIO support; once MFGPT support
is reworked to also be more generic, the older geode code will be removed.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: David Brownell <david-b@pacbell.net>
Reviewed-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The common adp5520 mfd defines were namespaced to avoid collisions, so
update the define used in this driver accordingly. The structs were also
renamed to fix a spelling typo.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This supports future devices with fewer GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- Remove wrong and unnecessary unmask operation
- Remove extra GEDR reading
This fixes the loss of interrupts which occurs when two or more pins are
triggered in close succession.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case of failure, device_create() returns not NULL but the error code.
The current code checks for non-NULL though which causes kernel oops in
sysfs_create_group() when device_create() fails. Check for error using
IS_ERR() and propagate the error value using PTR_ERR() instead of fixed
-ENODEV code returned now...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gpio_twl4030_probe() function calls gpio_twl4030_remove(), and the
former has __devinit, so the latter cannot use __devexit. Otherwise we
hit the section mismatch warning:
WARNING: drivers/gpio/built-in.o(.devinit.text+0x71a): Section mismatch
in reference from the function _gpio_twl4030_probe() to the function
.devexit.text:_gpio_twl4030_remove()
The function __devinit _gpio_twl4030_probe() references a function
__devexit _gpio_twl4030_remove().
This is often seen when error handling in the init function uses
functionality in the exit path.
The fix is often to remove the __devexit annotation of
_gpio_twl4030_remove() so it may be used outside an exit section.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Clearly mark ACPI drivers as such
i2c: Add driver for SMBus Control Method Interface
i2c-pnx: Correct use of request_region/request_mem_region
MAINTAINERS: Add maintainer for AT24 and PCA9564/PCA9665
i2c-piix4: Add AMD SB900 SMBus device ID
i2c/chips: Remove deprecated pcf8574 driver
i2c/chips: Remove deprecated pca9539 driver
i2c/chips: Remove deprecated pcf8575 driver
gpio/pcf857x: Copy i2c_device_id from old pcf8574 driver
i2c/scx200_acb: Provide more information on bus errors
i2c: Provide compatibility links for i2c adapters
i2c: Convert i2c adapters to bus devices
i2c: Convert i2c clients to a device type
i2c/tsl2550: Use combined SMBus transactions
i2c-taos-evm: Switch echo off to improve performance
i2c: Drop unused i2c_driver.id field
Many gpio chips allow to generate interrupts when the value of a pin
changes. This patch gives usermode application the opportunity to make
use of this feature by calling poll(2) on the /sys/class/gpio/gpioN/value
sysfs file. The edge to trigger can be set in the edge file in the same
directory. Possible values are "none", "rising", "falling", and "both".
Using level triggers is not possible with current sysfs since nothing
changes the GPIO value (and the IRQ keeps triggering). Edge triggering
will "just work". Note that if there was an event between read() and
poll(), the poll() returns immediately.
Also note that this version only supports true GPIO interrupts. Some
later patch might be able to synthesize this behavior by timer-driven
polling; some systems seem to need that.
[dbrownell@users.sourceforge.net: align ids to 16 bit ids; whitespace]
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers should be including <linux/gpio.h> not <asm/gpio.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MAX7315 is pin and software compatible with PCA9534, so add it to the I2C
device ID table of pca953x driver.
http://www.datasheetcatalog.org/datasheet/maxim/MAX7315.pdf
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Langwell chip is the IO hub for Intel Moorestown platform which has a
64-pin gpio block device inside. It is exposed as a dedicated PCI device.
We use it to control outside peripheral as well as to do IRQ demuxing.
The gpio block uses MSI to send level type interrupt to IOAPIC.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A GPIO driver for the Freescale MC33880 High/Low side switch
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 926b663ce8 (gpiolib: allow GPIOs to
be named) already provides naming on the chip level. This patch provides
more flexibility by allowing multiple names where ever in sysfs on a per
GPIO basis.
Adapted from David Brownell's comments on a similar concept:
http://lkml.org/lkml/2009/4/20/203.
[randy.dunlap@oracle.com: fix build for CONFIG_GENERIC_GPIO=n]
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial patch which adds the __init/__exit macro to the init/exit functions of
drivers/gpio/bt8xxgpio.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The deprecated pcf8574 driver is going to be removed. Make sure the
replacement driver inherits all i2c_device_ids for a smooth transition.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the GPIO pins on the WM831x. No direct support is
currently supplied for configuring non-gpiolib functionality such
as pull configuration and alternate functions, soft configuration
of these will be provided in a future patch.
Currently use of these pins as interrupts is not supported due to
the ongoing issues with generic irq not support interrupt controllers
on interrupt driven buses. Users can directly request the interrupts
with the wm831x-specific APIs currently provided if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
