Instead of hard wiring the WCLK frequency at probe time do it runtime.
The hard wired 88_96KHz was not even setting the correct bits since it was
defined as (1 << 6) which will change the I2S_OUT_SEL bit and will leave
the amplifier configured for 8KHz.
At the same time clean up and fix the CFG3 register bits.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Configure the word length based on the params_width of the stream.
Also configure the clock per frame value which is used when tas2552 is bus
master.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain sequence need to be followed in order to have smooth power up and
power down performance.
Execute this sequence via DAPM_POST widget.
Remove patching the RESERVED_0D register at probe time since it has to be
handled every time when we stop or start the amplifier.
In order to be able to execute the sequence at the correct time, the driver
need to request to ignore the pmdown time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The last parameter for DECLARE_TLV_DB_SCALE() is to tell if the gain will
be muted or not when it is set to raw 0. IN this case it is not muted.
The PGA_GAIN is in 0-4 bits in the register. Fix the offset in the
SOC_SINGLE_TLV() for this.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The strings should be: 'static const char * const tas2552_input_texts[]'
SOC_DAPM_ENUM should have "Route" in place of xname and no need to have it
as an array.
Also align the parameters.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM support is achieved using DSP transfer mode and setting a programmable
offset which specifies where data begins with respect to the frame sync.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use names from the datasheet for the definitions.
Correct the data format definitions since they were not correct.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP_A mode require one bit delay from the FS, DSP_B is without data delay.
When checking the requested format, also match the bit and fs inversion
flag along with the format since it is not possible to change inversion.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of hard wiring the PLL_CLKIN and PDM_CLK to be sourced from BCLK add
proper clock configuration via the set_dai_sysclk callback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Binding header file for clock input selection and configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prevents frequent panic on boot, if the irq handler rt5645_irq
gets called before the workqueue rt5645_jack_detect_work is
initialized.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
MCLK is one of the possible source for the pll_clkin frequency. Make this
clear by renaming the variable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function name and parameters of:
tas2552_sw_shutdown(struct tas2552_data *tas_data, int sw_shutdown)
implies that if sw_shutdown is 1 we should be entering to the software
shutdown mode.
The code can be simplified as well within the function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialize the cfg1_reg to 0 and set the mute bit only when it is needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the _MASK postfix of the bit definitions, collect the CFG1 bit
definition in one place and correct the bit shifts at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PDM clock can be selected via bit0-1.
PDM_DATA_ES bit is at bit2.
The code were trying to select BCLK as PDM reference clock but instead
it was selecting PLL and set the DATA_ES bit to 1.
Selecting the PLL output as reference clock as default does make sense,
but the driver should not change the PDM data edge.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SOC_DAPM_SINGLE("Playback AMP", ..) should not be under kcontrols. It
causes kernel crash (NULL pointer) when the mixers are listed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the card is not part of any card the tas_data->codec is NULL since it is
set only during snd_soc_codec_driver.probe, which is not yet called.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Do not fail the probe if the enable-gpio is not specifiedbut handle
deferred probe case.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following error:-
All error/warnings (new ones prefixed by >>):
>
> sound/built-in.o: In function `soc_tplg_dapm_widget_create':
> >> :(.text+0x25a90): undefined reference to `snd_soc_dapm_new_control'
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure userspace can define TLV controls for topology using the correct
type numbers and channel mappings.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The topology core parses the FW topology file for known block types and
instanciates any common ALSA/ASoC objects that it discovers. The core
also passes any block that is does not understand to client component
drivers for enumeration.
The core exports some APIs to client drivers in order to load and unload
firmware topology data as use case require.
Currently the core deals with the following object types :-
o kcontrols. This includes TLV, enumerated and bytes controls.
o DAPM widgets. All types with any associated kcontrol.
o DAPM graph.
o FE PCM. FE PCM capabilities and configuration can be defined.
o BE DAI Link. BE DAI link capabilities and configuration can be defined.
o Codec <-> codec style links capabilities and configuration.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC topology UAPI header defines the structures
required to define any DSP firmware audio topology and control objects from
userspace.
The following objects are supported :-
o kcontrols including TLV controls.
o DAPM widgets and graph elements
o Vendor bespoke objects.
o Coefficient data
o FE PCM capabilities and config.
o BE link capabilities and config.
o Codec <-> codec link capabilities and config.
o Topology object manifest.
The file format is simple and divided into blocks for each object type and
each block has a header that defines it's size and type. Blocks can be in
any order of type and can either all be in a single file or spread across
more than one file. Blocks also have a group identifier ID so that they can
be loaded and unloaded by ID.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If an ASoC component device does not have a device tree node, use its
parent's node instead, when looking for a matching DAI based on a
device tree reference.
This allows video device drivers to register a separate child device
for their ASoC side audio functionality. [And MFDs in general --
broonie]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using the driver for the internal regulator to also enable/disable
the codec internal clock frequency controller is an unexpected
side-effect for a regulator, and also means that the core clocks
won't be changed as expected if an external regulator is used to
power the codec.
The DVFS is now handled by the codec driver so can be removed from
the LDO1 driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8997 and WM5102 codecs need to boost DVFS for higher sample rates.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In theory the ADSP driver should not need to know anything
about the codec it is part of. But the WM5102 needs DVFS
control based on ADSP clocking speed. This was being handled
by bundling part of the knowledge of this into the ADSP driver.
This change moves this handling out of the ADSP driver and
into the WM5102 driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM5102 and WM8997 codecs have an internal dynamic clock booster.
When this booster is active, the DCVDD voltage must be increased.
If all the currently active audio paths can run with the root SYSCLK
we can disable the booster, allowing us to turn down DCVDD voltage
to save power.
Previously this was being done by having the booster enable bit set
as a side-effect of the LDO1 regulator driver, which is unexpected
behaviour of a regulator and not compatible with using an external
regulator. [Originally this was documented as a feature of the internal
LDO -- broonie]
This patch exports functions to handle the booster enable and
DCVDD voltage, with each relevant subsystem flagging whether it can
currently run without the booster. Note that these subsystems are
stateless and none of them are nestable, so there's no need for
reference counting, we only need a simple boolean for each subsystem
of whether their current condition could require the booster or will
allow us to turn the codec down to lower operating power.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch is a fixup to correct dependencies in patch 9bae4880ac
("ASoC: qcom: move ipq806x specific bits out of lpass driver.")
Originally this change-set was suggested by Arnd on mailing list.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The change fixes the following compilation problem:
sound/soc/soc-dapm.c: In function 'dapm_kcontrol_data_alloc':
sound/soc/soc-dapm.c:388:4: error: implicit declaration of function
'snd_soc_dapm_new_control' [-Werror=implicit-function-declaration]
data->widget = snd_soc_dapm_new_control(widget->dapm,
^
sound/soc/soc-dapm.c:387:17: warning: assignment makes pointer
from integer without a cast [enabled by default]
data->widget = snd_soc_dapm_new_control(widget->dapm,
^
sound/soc/soc-dapm.c: At top level:
sound/soc/soc-dapm.c:3269:1: error: conflicting types for
'snd_soc_dapm_new_control'
snd_soc_dapm_new_control(struct snd_soc_dapm_context *dapm,
^
In addition to the fix add static qualifier to
snd_soc_dapm_new_control() function to silence checkpatch.
Fixes: 02aa78abec ("ASoC: DAPM: Add APIs to create individual DAPM controls.")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
