Remove the pseudo-hwmods associated with hardreset lines from the
OMAP4 data file. Future patches will convert this data to register
hwmods by interfaces, rather than registering hwmods directly. The
pseudo-hwmods aren't associated with any interfaces, so this will
create a problem.
After this change, the hwmod code will reset processor IPs at the
hwmod level, rather than by individual hardreset lines. So, for
example, if the IVA device driver code wishes to place one of the
sequencer cores into reset, while leaving the other active, it must do
so itself by calling the appropriate PRM functions.
This patch will cause a change in the initialization behavior of the
DSP, IVA, and IPU.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Due to HW limitation, some IPs should not be accessed just after a
softreset. Since the current hwmod sequence is accessing the sysconfig
register just after the reset, it might lead to OCP bus error in
that case.
Add a new field in the sysconfig structure to specify a delay in usecs
needed after doing a softreset.
In the case of the ISS and FDIF modules, the L3 OCP port will be
disconnected upon a SW reset. That issue was confirmed with HW simulation
and an errata should be available soon. The HW recommendation to avoid
that is to wait for 100 OCP clk cycles, before accessing the IP.
Considering the worse case (OPP50), the L3 bus will run at 100 MHz,
so a 1 usec delay is needed. Add an x2 margin to be safe.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: dropped FDIF change for now since the hwmod data is not
yet upstream; the FDIF change will need to be added later once the FDIF
data is merged]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
CLKS signal for McBSP ports can be selected from internal (PRCM) or
external (ABE_CLKS pin) source. To be able to use existing code we
need to create clock aliases consistent among OMAP2/3/4.
Based on a patch from Péter Ujfalusi <peter.ujfalusi@ti.com>;
the patch description above is his.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Conflicts:
arch/arm/mach-lpc32xx/clock.c
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The conflicts with pxa are non-obvious, we have multiple branches
adding and removing the same clock settings. According to
Haojian Zhuang, removing the sa1100 rtc dummy clock is the correct
fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arch/arm/mach-omap2/: included some headers tiwce:
- arch/arm/mach-omap2/board-ldp.c: 'linux/gpio.h'
- arch/arm/mach-omap2/io.c: 'common.h'
- arch/arm/mach-omap2/omap_hwmod_44xx_data.c: 'plat/i2c.h'
Remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To set sr ntarget values for all volt_domain,
volt_table is retrieved by doing a look_up of 'vdd_name'
field from omap_hwmod but voltage domain pointer does not
belong to omap_hwmod and is not used anywhere else.
As a part of voltage layer and SR Layer clean up volt
pointer is removed from omap_hwmod and added in dev
attributes of SR. The value of the field must match
the voltage domain names for the binding to be effective.
Tested on OMAP3630 SDP, OMAP3530 Beagleboard and
OMAP4430 SDP Board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
To be able to get the memory resources by name from
the DMIC driver (for MPU and for DMA).
Without this patch, functionality that was working in 3.2 breaks in
3.3-rc1. This patch should have gone in as part of the 3.3 merge
window, but was inadvertently missed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: added commit message note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For I2C clockactivity field is added for OMAP3 and OMAP4 that defines how the
interface (OCP) and functional (system) clocks behave when the I2C module is
idle.
The configuration of the clock activity bit field (per TRM) is as follows:
0x0: Both clocks can be cut off
0x1: Only OCP clock must be kept active; system clock
can be cut off
0x3: Both clocks must be kept active
0x2: Only system clock must be kept active; OCP clock
can be cut off
The patch makes 0x2(CLOCKACT_TEST_ICLK) the default for OMAP3 and OMAP4.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Following 2 hwmod structures are added
1. usb_host_hs
The hwmod of usbhs with uhh, ehci and ohci base addresses
functional clock and ehci, ohci irqs
2. usb_tll_hs
hwmod of usbhs with the TLL base address and irq.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[keshava_mgowda@ti.com: rebased to kernel version 3.0, added workarounds for
hardware issues]
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
[paul@pwsan.com: fixed multi-line comments, fixed whitespace, fixed S-o-b
notes, removed spurious TLL->L3 interface]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.
Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.
Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.
This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.
Thanks to Tomi and Sricharan for some additional testing.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP4 HWMOD data currently contains errors with DSS clocks:
dss_hdmi and dss_venc have their main_clks wrong. The clocks should be
dss_48mhz_clk and dss_tv_clk, respectively.
These problems were temporarily fixed with the DSS patches
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), and df5d3ed23c ("OMAP:
DSS2: HDMI: fix hdmi clock name"), which can be reverted after this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This causes the HWMOD frameworks boot-time
reset to fail, possibly leaving the DSS hardware in undefined state.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET for dss_core. The flag
is actually not used on OMAP4, because dss_core hardware does not have
soft-reset functionality and thus the HWMOD framework never resets nor
waits for the reset to finish.
However, while the flag is not strictly needed currently, I think it
represents the HW correctly: all the DSS clocks should be enabled after
power-on to allow DSS hardware to finish its reset.
A custom reset function will be added in the following patches which
manages this correctly for OMAP4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the dss_dss_clk from dss_core's opt-clocks. dss_dss_clk already
defined as the dss main_clk, and thus is not needed as an opt-clock.
Remove opt-clocks for dss_dispc, as dispc only uses the main_clk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add routines to converts dmtimers to platform devices. The device data
is obtained from hwmod database of respective platform and is registered
to device model after successful binding to driver.
In addition, capability attribute of each of the timers is added in
hwmod database.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At Tony's request, remove the OMAP_CHIP* flags from the hwmod data, and
replace it instead with chip family, variant, and ES level-specific lists
of hwmods to register.
Thanks to Gražvydas Ignotas <notasas@gmail.com> for finding a bug in the
AM3517/3505 support, and for other review comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Add a new field to provide the mode supported by the module.
The mode will control the way mandatory clocks are managed by the PRCM.
0 : Module is temporarily disabled by SW. OCP access to module are stalled.
Can be used to change timing parameter of GPMC module.
1 : Module is managed automatically by HW according to clock domain
transition. A clock domain sleep transition put module into idle.
A wakeup domain transition put it back into function.
If CLKTRCTRL=3, any OCP access to module is always granted.
Module clocks may be gated according to the clock domain state.
2 : Module is explicitly enabled. Interface clock (if not used for
functions) may be gated according to the clock domain state.
Functional clocks are guarantied to stay present. As long as
in this configuration, power domain sleep transition cannot happen.
Some modules will have a modulemode initialized at 1 (HWCTRL) by default.
This is the case for interconnect and simple module like GPIO, WDT, MAILBOX.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a 'context_offs' entry in the prcm.omap4 structure to all
IPs when applicable.
The offset will be used to retrieve the per module context lost
information now available on OMAP4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The RSTCTRL register was accessed using an absolute address.
The usage of hardcoded macros to calculate virtual address from physical
one should be avoided as much as possible.
The usage of an offset will allow future improvement like migration from
the current architecture code toward a module driver.
Update prm_xxx accessors, move definition to the proper header file and
update copyrights.
Change the s16 register offset parameter to u16.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use '_prminst_' in function names that are part of the
prminst44xx.c file]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The CLKCTRL register was accessed using an absolute address.
The usage of hardcoded macros to calculate virtual address from physical
one should be avoided as much as possible.
The usage of a offset will allow future improvement like migration from
the current architecture code toward a module driver.
Update cm_xxx accessor, move definition to the proper header file and
update copyrights.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Todd Poynor <toddpoynor@google.com>
[paul@pwsan.com: renamed 'omap4_cm_' fns to 'omap4_cminst_'; removed empty
fn prototype section from cm44xx.h; incorporated comments from Todd;
documented some functions]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In OMAP PRCM terminology, the clock domain is defined as a group of IPs
that share some clocks and most of the time an interface clock.
Every IP does belong to a clockdomain.
For the moment the clock domain attribute is affected to a clock node.
The issue with that approach, is that a clock might or not belong to a
clock domain. Moreover during module transition, it is up to a module
to handle properly the clock domain state and not to a clock node.
Create a clkdm_name attribute to provide this information per hwmod.
Populate this attribute for every OMAP4 hwmod entries.
Future cleanup series with remove that information from the OMAP4 clock
when it is relevant.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: fix the mpuss_clkdm name]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The sequence of _ocp_softreset doesn't work for i2c. The i2c module has a
special sequence to reset the module. The sequence is
- Disable the I2C.
- Write to SOFTRESET bit.
- Enable the I2C.
- Poll on the RESETDONE bit.
The sequence is implemented as a function and the i2c_class is updated with
the correct 'reset' pointer. omap_hwmod_softreset function is implemented
which triggers the softreset by writing into sysconfig register. On following
this sequence, i2c module resets properly and timeouts are not seen.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
[paul@pwsan.com: combined this patch with a patch to remove
HWMOD_INIT_NO_RESET from the 44xx hwmod flags; change register
offset conditional code to use the IP block revision; minor code
cleanup]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This adds the new functionality flags for omap i2c unit to all OMAP2
hwmod definitions
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since we cannot trust (or even reliably find) the OMAP I2C
peripheral unit's own revision register, we must inform the
OMAP i2c driver of which IP version it is running on. We
do this by tagging the omap_hwmod_class for i2c on all the
OMAP2+ platform / cpu specific hwmod init and passing it up
to the driver (next patches).
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Peter Maydell noticed when running under QEMU he was getting
errors reporting 32-bit access to I2C peripheral unit registers
that are documented to be 8 or 16-bit only[1][2]
The I2C driver is blameless as it wraps its accesses in a
function using __raw_writew and __raw_readw, it turned out it
is the hwmod stuff.
However the hwmod code already has a flag to force a
perhipheral unit to only be accessed using 16-bit operations.
This patch applies the 16-bit only flag to the 2430,
OMAP3xxx and OMAP44xx hwmod structs. 2420 was already
correctly marked up as 16-bit.
The 2430 change will need testing by TI as arranged
in the comments to the previous patch version.
When the 16-bit flag is or-ed with other flags, it is placed
first as requested in comments.
[1] OMAP4430 Technical reference manual section 23.1.6.2
[2] OMAP3530 Techincal reference manual section 18.6
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently using pm_runtime with DSS requires the DSS driver to enable
the DSS functional clock before calling pm_runtime_get(). That makes it
impossible to use pm_runtime in DSS as it is meant to be used, with
pm_runtime callbacks.
This patch changes the hwmod database for OMAP4 so that enabling the
hwmod via pm_runtime will also enable the DSS functional clock, allowing
us to use pm_runtime properly in DSS driver.
The DSS HWMOD side is not really correct, not before nor after this
patch, and getting DSS to retention will probably not work currently.
However, it is not supported in the mainline kernel anyway, so this
won't break anything.
So this patch allows us to write the pm_runtime adaptation for the DSS
driver the way it should be done, and the HWMOD/PM side can be fixed
later.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add missing DSS optional clocks to HWMOD data for OMAP4xxx.
Add HWMOD_CONTROL_OPT_CLKS_IN_RESET flag for dispc to fix dispc reset.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[b-cousson@ti.com: Remove a comment and update the subject]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: removed DSS "fck" role and some clkdev aliases at Tomi's
request]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The interconnect modules were using a slightly different layout than
the regular modules.
Align the layout for better consitency.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fix .prcm alignement and usb_otg_hs class and hwmod structures.
Add a couple of more potential hwmods in the comment.
Remove hsi, since it is already included in the data.
Remove one blank line.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
A couple of parens were added around some flags.
Remove them, since they are not needed and not used
for any other hwmods.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Change the position of the ocp_if structure to match the template.
Remove unneeded comma at the end of address space flag field.
Remove USER_SDMA since this ocp link is only from the l3_main_1
path that is accessible only from the MPU in that case and not
the SDMA.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Previously, struct omap_hwmod_dma_info arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array. However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.
So far this hasn't been a problem. However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file. When this is done, ARRAY_SIZE() will no longer be usable.
This patch removes ARRAY_SIZE() usage for struct omap_hwmod_dma_info
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Previously, struct omap_hwmod_mpu_irqs arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array. However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.
So far this hasn't been a problem. However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file. When this is done, ARRAY_SIZE() will no longer be usable.
This patch removes ARRAY_SIZE() usage for struct omap_hwmod_mpu_irqs
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Previously, struct omap_hwmod_addr_space arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array. However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.
So far this hasn't been a problem. However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file. When this is done, ARRAY_SIZE() will no longer be usable.
This patch removes ARRAY_SIZE() usage for struct omap_hwmod_addr_space
arrays and uses a null structure member as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the flag to every IPs that support it to allow the
framework to enable it instead of the SMART_STANDBY default
mode.
Without that, an IP with busmaster capability will not
be able to wakeup the interconnect at all.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 407a6888f7 (OMAP4: hwmod data:
Add AESS, McPDM, bandgap, counter_32k, MMC, KBD, ISS & IPU) added the
entry for keypad, but did not enable it.
Enable the keypad in the hwmod database so it works.
Signed-off-by: Shubhrajyoti D<shubhrajyoti@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP2420, 2430 and 3xxx were using the OMAP4 end address
that unfortunately is not located at the same base address.
Moreover the OMAP4 size was set to 256 instead of 4096.
Change all .pa_end to set them to .pa_start + 0xfff
Cc: "G, Manjunath Kondaiah" <manjugk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Reported-by: Michael Fillinger <m-fillinger@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod change is aligned with Benoit Cousson.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
The following commit: 38698be:
OMAP2+: clockevent: set up GPTIMER clockevent hwmod right before timer init
Fixed properly the issue with early init for the timer1
So reverts commit 3b03b58dab that is now
generated a warning at boot time.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a device attribute to hwmod data of omap2430, omap3, omap4.
Currently the device attribute holds information regarding dual volt MMC card
support by the controller which will be later passed to the host driver via
platform data.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename omap_hwmod_init() to omap_hwmod_register(). Rename
omap_hwmod_late_init() to omap_hwmod_setup_all(). Also change all of
the callers to reflect the new names. While here, update some
copyrights.
Suggested by Tony Lindgren <tony@atomide.com>.
N.B. The comment in mach-omap2/serial.c may no longer be correct, given
recent changes in init order.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Added a name to address space belonging to SDMA and MPU facilitating
the driver to get the address space info by name. Added a revision
member inorder to facilitate the driver to differentiate between
mcbsp in different omap.
Also added a platform_get_irq in probe to get irq number by index since
from OMAP4, there will be a single irq line.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since the timer1 is now started before the hwmod_init, we cannot
reset it and idle it anymore.
Add the appropriate flags to prevent the hwmod framework to do that.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Add a rev attribute to identify various McSPI IP version.
- Add a dev_attr structure to provide the number of chipselect
supported by the instance.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 hwmod data structures are populated with base address, L3 and L4
interface clocks, IRQs and sysconfig register details.
As per OMAP USBOTG specification, need to configure the USBOTG
to smart idle/standby or no idle/standby during data transfer and
force idle/standby when not in use to support retention and offmode.
By setting HWMOD_SWSUP_SIDLE and HWMOD_SWSUP_MSTANDBY flags,framework
will take care of configuring to no idle/standby when module is enabled
and force idle/standby when idled.
Signed-off-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[b-cousson@ti.com: Fix position, opt_clk, and author]
Add more hwmod structures but keep them commented out for the moment
until the driver adaptation to hwmod / omap_device is done.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Add mcbsp data including a revision member in hwmod_class in
order to provide mcbsp revision information in different omap.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
[b-cousson@ti.com: Remove the mcbsp4 memory name, re-order
properly the structures]
Add HWMOD entries for the OMAP DMIC. The HWMOD entires define the system
resource requirements for the driver such as DMA addresses, channels,
and IRQ's. Placing this information in the HWMOD database allows for
more generic drivers to be written and having the specific implementation
details defined in HWMOD.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: David Lambert <dlambert@ti.com>
[b-cousson@ti.com: Change the wrong hwmod name,
add missing flag and re-order structures]
Mailbox hwmod data for omap4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[b-cousson@ti.com: Re-order the structures
and remove the irq line name]
Add dss, dispc, dsi1, dsi2, hdmi, rfbi and venc hwmods.
In OMAP4 there are severals IPs that can be reached by differents
interconnect paths depending of the access initiator (MPU vs. SDMA).
In the case of the DSS, both L3 direct path and L4 CFG path can be
used to access all the DSS IPs. The two ocp_ip already exists to support
the two address spaces.
+------------+-- L3_MAIN --+ MPU
IP | |
+-- L4_CFG --+
L3 main address range is specified first, since it is used by default.
dss is also considered as an IP as dispc, rfbi, and named as dss_core.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
[b-cousson@ti.com: Re-organize structures to match file
convention and remove irq entry from dss_hwmod]
Add the data for the 11 timers IPs.
OMAP4 contains two differents IP variants for the timers:
- 8 x regular timer (3, 4, 5, 6, 7, 8, 9 & 11)
- 3 x 1ms timer (1, 2 & 10)
The regular timers registers programming model was changed due to the
adaptation to the new IP interface. Unfortunately the 1ms version
still use the previous programming model. The driver will have
to take care of theses differences.
Please note that the capability and the partitioning is also
different depending of the instance.
- timer 1 is inside the wakeup domain
- timers 5, 6, 7 & 8 are inside in the ABE (audio backend)
- timers 2, 3, 4, 9, 10 & 11 are inside the PER power domain
The timer was previously named gptimerX or dmtimerX, it is
now simply named timerX.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
[b-cousson@ti.com: Fix alignement in class attribute,
re-order flags and update the changelog]
Add hwspinlock hwmod data for OMAP4 chip
Signed-off-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Paul Walmsley <paul@pwsan.com>
[b-cousson@ti.com: Move the data to keep the original
order and add missing SIDLE_SMART_WKUP flag]
In order to be fully aligned with the Python generator output,
change a couple of fields.
- Add tab in class structures to align attributes
- Add a comma at the end of the following line to simplify
the generation by having always the same eol:
".pre_shutdown = &omap2_wd_timer_disable,"
- Add a blank line before the first entry of the
omap44xx_hwmods array.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The merge of the DMA series on top of the already modified
omap_hwmod_data_44xx.c put the dma_system structures at
the wrong position in the file.
Re-order it properly.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The merge of the SR series on top of the already modified
omap_hwmod_data_44xx.c moved the smartreflex structures at the wrong
position in the file.
- Re-order the structures properly.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the missing SIDLE_SMART_WKUP flag in idlemodes field of
the smartreflex sysconfig structure.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Thara Gopinath <thara@ti.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the hwmod details for OMAP4 smartreflex modules.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
uart, gpio, wd_timer and i2c does support the new smart-idle with wakeup
added in OMAP4.
Add the flag to allow the hwmod core to enable this mode when applicable.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Fix opt clocks name in clock framework and hwmod.
Add the missing iclk in the ocp_if structure.
Add the HWMOD_CONTROL_OPT_CLKS_IN_RESET flag to ensure
the the GPIO optional clock is enable during reset.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Charulatha V <charu@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Add IVA and DSP hwmods in order to allow the pm code to
initialize properly the processors devices during
omap2_init_processor_devices.
It will avoid the following warnings.
_init_omap_device: could not find omap_hwmod for iva
_init_omap_device: could not find omap_hwmod for dsp
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The DMM is a piece of interconnect that need to be configured properly
for the tiler functionnality. It thus exposes some configuration registers
that were missing previously.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Update the data for GPIO, UART, WD_TIMER and I2C in order to
support the new reset status flag introduce in the following
commit:
commit 2cb068149c
OMAP: hwmod: Fix softreset status check for some new OMAP4 IPs
Without this flag properly set, the reset is done, but the hwmod
core code will not wait for the reset completion to continue its
excecution.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Charulatha V <charu@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The original OMAP4 hwmod data files is fully generated from HW
database. But since the file is introduced incrementaly along
with driver that uses the data, it has to be splitted by the driver
owner and then re-merged by the maintainer.
Because of the similarity of the data, git is completely lost
during such merge and thus the data does not look like the original one
at the end.
Re-order properly the structures to stay in sync with original data set.
This makes it much easier to diff the autogenerated script output with
what's in mainline, see differences, and generate patches for those
diffs. The goal is to stay in sync with the autogenerated data from now
on.
Add a comment that does contain all the IPs that can have a hwmod, but
do not have it in the file for the moment. It gives a good indication
of the progress.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: updated to apply against current core integration branch,
commit message slightly amplified; fixed opt_clks_cnt whitespace]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Cc: Charulatha V <charu@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Split the existing cm44xx.h file into cm1_44xx.h and cm2_44xx.h files
so they match their underlying OMAP hardware modules. Add clockdomain
offset information.
Add header files for the MPU local PRCM, prcm_mpu44xx.h, and for the
SCRM, scrm44xx.h. SCRM register offsets still need to be added; TI
should do this.
Move the "_MOD" macros out of the prcm-common.h header file, into the
header file of the hardware module that they belong to. For example,
OMAP4430_PRM_*_MOD macros have been moved into the prm44xx.h header.
Adjust #includes of all files that used the old PRCM header file names
to point to the new filenames.
The autogeneration scripts have been updated accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The OMAP watchdog timer IP blocks require a specific set of register
writes to occur before they will be disabled[1], even if the device
clocks appear to be disabled in the CM_*CLKEN registers. In the MPU
watchdog case, failure to execute this reset sequence will eventually
cause the watchdog to reset the OMAP unexpectedly.
Previously, the code to disable this watchdog was manually called from
mach-omap2/devices.c during device initialization. This causes the
watchdog to be unconditionally disabled for a portion of kernel
initialization. This should be controllable by the board-*.c files,
since some system integrators will want full watchdog coverage of
kernel initialization. Also, the watchdog disable code was not
connected to the hwmod shutdown code. This means that calling
omap_hwmod_shutdown() will not, in fact, disable the watchdog, and the
goal of omap_hwmod_shutdown() is to be able to shutdown any on-chip
OMAP device.
To resolve the latter problem, populate the pre_shutdown pointer in
the watchdog timer hwmod classes with a function that executes the
watchdog shutdown sequence. This allows the hwmod code to fully
disable the watchdog.
Then, to allow some board files to support watchdog coverage
throughout kernel initialization, add common code to mach-omap2/io.c
to cause the MPU watchdog to be disabled on boot unless a board file
specifically requests it to remain enabled. Board files can do this
by changing the watchdog timer hwmod's postsetup state between the
omap2_init_common_infrastructure() and omap2_init_common_devices()
function calls.
1. OMAP34xx Multimedia Device Silicon Revision 3.1.x Rev. ZH
[SWPU222H], Section 16.4.3.6, "Start/Stop Sequence for WDTs (Using
WDTi.WSPR Register)"
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Charulatha Varadarajan <charu@ti.com>
Add OMAP4 DMA hwmod data. In addition to original dma hwmod data,
the following changes are added.
1. DMA device attributes structure is introduced for diffenrenciating
OMAP cpu's based on DMA features.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP4
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add uart1-4 hwmod data into omap4_hwmod data file.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add watchdog timer hwmod data for OMAP4 chip
Note: wd_timer3 in enabled in the hwmod list but it is
not yet supported by the watchdog driver.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current version contains only the interconnects and the
mpu hwmods.
The remaining hwmods will be introduced by further patches on
top of this one.
- enable as well omap_hwmod.c build for OMAP4 Soc
Please not that this file uses the new naming convention for
naming HW IPs. This convention will be backported soon for previous
OMAP2 & 3 data files.
new name trm name
------------- -------------------
counter_32k synctimer_32k
l3_main l3
timerX gptimerX / dmtimerX
mmcX mmchsX / sdmmcX
dma_system sdma
smartreflex_X sr_X / sr?
usb_host_fs usbfshost
usb_otg_hs hsusbotg
usb_tll_hs usbtllhs_config
wd_timerX wdtimerX
ipu cortexm3 / ducati
dsp c6x / tesla
iva ivahd / iva2.2
kbd kbdocp / keyboard
mailbox system_mailbox
mpu cortexa9 / chiron
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
