qla2x00_probe_one() allocates IRQs before it initializes rsp_q_map so
IRQs must be freed even if rsp_q_map allocation did not occur. This was
detected by kmemleak.
Fixes: 4fa1834559 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Michael Hernandez <michael.hernandez@cavium.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-By: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the case of a graceful set of detaches, where the virtio-scsi-ccw
disk is removed from the guest prior to the controller, the guest
behaves quite normally. Specifically, the detach gets us into
sd_sync_cache to issue a Synchronize Cache(10) command, which
immediately fails (and is retried a couple of times) because the device
has been removed. Later, the removal of the controller sees two CRWs
presented, but there's no further indication of the removal from the
guest viewpoint.
[ 17.217458] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 17.219257] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 21.449400] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
[ 21.449406] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
However, on s390, the SCSI disks can be removed "by surprise" when an
entire controller (host) is removed and all associated disks are removed
via the loop in scsi_forget_host. The same call to sd_sync_cache is
made, but because the controller has already been removed, the
Synchronize Cache(10) command is neither issued (and then failed) nor
rejected.
That the I/O isn't returned means the guest cannot have other devices
added nor removed, and other tasks (such as shutdown or reboot) issued
by the guest will not complete either. The virtio ring has already been
marked as broken (via virtio_break_device in virtio_ccw_remove), but we
still attempt to queue the command only to have it remain there. The
calling sequence provides a bit of distinction for us:
virtscsi_queuecommand()
-> virtscsi_kick_cmd()
-> virtscsi_add_cmd()
-> virtqueue_add_sgs()
-> virtqueue_add()
if success
return 0
elseif vq->broken or vring_mapping_error()
return -EIO
else
return -ENOSPC
A return of ENOSPC is generally a temporary condition, so returning
"host busy" from virtscsi_queuecommand makes sense here, to have it
redriven in a moment or two. But the EIO return code is more of a
permanent error and so it would be wise to return the I/O itself and
allow the calling thread to finish gracefully. The result is these four
kernel messages in the guest (the fourth one does not occur prior to
this patch):
[ 22.921562] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
[ 22.921580] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
[ 22.921978] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 22.921993] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
I opted to fill in the same response data that is returned from the more
graceful device detach, where the disk device is removed prior to the
controller device.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
mpt3sas has a firmware failure where it can only handle one pass through
ATA command at a time. If another comes in, contrary to the SAT
standard, it will hang until the first one completes (causing long
commands like secure erase to timeout). The original fix was to block
the device when an ATA command came in, but this caused a regression
with
commit 669f044170
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Tue Nov 22 16:17:13 2016 -0800
scsi: srp_transport: Move queuecommand() wait code to SCSI core
So fix the original fix of the secure erase timeout by properly
returning SAM_STAT_BUSY like the SAT recommends. The original patch
also had a concurrency problem since scsih_qcmd is lockless at that
point (this is fixed by using atomic bitops to set and test the flag).
[mkp: addressed feedback wrt. test_bit and fixed whitespace]
Fixes: 18f6084a98 (mpt3sas: Fix secure erase premature termination)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reported-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set the elsiocb contexts to NULL after freeing as others depend on it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no good match of the zoned field of the block device
characteristics page for host-managed devices. For these devices, the
zoning model is derived directly from the device type. So ignore the
zoned field for these drives.
[mkp: typo]
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Zoned block devices force the use of READ/WRITE(16) commands by setting
sdkp->use_16_for_rw and clearing sdkp->use_10_for_rw. This result in
DPOFUA always being disabled for these drives as the assumed use of
the deprecated READ/WRITE(6) commands only looks at sdkp->use_10_for_rw.
Strenghten the test by also checking that sdkp->use_16_for_rw is false.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 01e0e15c8b ("scsi: don't use fc_bsg_job::request and
fc_bsg_job::reply directly") introduced a typo, which causes that the
bsg_request variable in bfad_im_bsg_els_ct_request() is initialized to
itself instead of pointing to the bsg job's request.
Reported-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The call to scsi_is_sas_rphy() needs to be made on the SAS end_device,
not on the SCSI device.
Fixes: 835831c57e ("ses: use scsi_is_sas_rphy instead of is_sas_attached")
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set variables initialized in lpfc_sli4_alloc_resource_identifiers() to
NULL if an error occurred. Otherwise, lpfc_sli4_driver_resource_unset()
attempts to free the memory again.
Signed-off-by: Roberto Sassu <rsassu@suse.de>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that qla2xxx uses the IRQ layer affinity assignment, affinity won't
change over the life time of a device and the notifiers are useless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The first two or three vectors in qla2xxx adapter are global and not
associated with a specific queue. They should not have IRQ affinity
assigned.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 093df73771 ("scsi: qla2xxx: Fix Target mode handling with
Multiqueue changes.") introduces two bodies of code that look similar
but with s/req/rsp/ in the second instance. But in one case, it looks
like this conversion was missed.
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Quinn Tran <Quinn.Tran@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a race condition with qla2xxx optrom functions where one thread
might modify optrom buffer, optrom_state while other thread is still
reading from it.
In couple of crashes, it was found that we had successfully passed the
following 'if' check where we confirm optrom_state to be
QLA_SREADING. But by the time we acquired mutex lock to proceed with
memory_read_from_buffer function, some other thread/process had already
modified that option rom buffer and optrom_state from QLA_SREADING to
QLA_SWAITING. Then we got ha->optrom_buffer 0x0 and crashed the system:
if (ha->optrom_state != QLA_SREADING)
return 0;
mutex_lock(&ha->optrom_mutex);
rval = memory_read_from_buffer(buf, count, &off, ha->optrom_buffer,
ha->optrom_region_size);
mutex_unlock(&ha->optrom_mutex);
With current optrom function we get following crash due to a race
condition:
[ 1479.466679] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1479.466707] IP: [<ffffffff81326756>] memcpy+0x6/0x110
[...]
[ 1479.473673] Call Trace:
[ 1479.474296] [<ffffffff81225cbc>] ? memory_read_from_buffer+0x3c/0x60
[ 1479.474941] [<ffffffffa01574dc>] qla2x00_sysfs_read_optrom+0x9c/0xc0 [qla2xxx]
[ 1479.475571] [<ffffffff8127e76b>] read+0xdb/0x1f0
[ 1479.476206] [<ffffffff811fdf9e>] vfs_read+0x9e/0x170
[ 1479.476839] [<ffffffff811feb6f>] SyS_read+0x7f/0xe0
[ 1479.477466] [<ffffffff816964c9>] system_call_fastpath+0x16/0x1b
Below patch modifies qla2x00_sysfs_read_optrom,
qla2x00_sysfs_write_optrom functions to get the mutex_lock before
checking ha->optrom_state to avoid similar crashes.
The patch was applied and tested and same crashes were no longer
observed again.
Tested-by: Milan P. Gandhi <mgandhi@redhat.com>
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bna & bfa firmware version 3.2.5.1 was submitted to linux-firmware on
Feb 17 19:10:20 2015 -0500 in 0ab54ff1dc ("linux-firmware: Add QLogic BR
Series Adapter Firmware").
bna was updated to use the newer firmware on Feb 19 16:02:32 2015 -0500 in
3f307c3d70 ("bna: Update the Driver and Firmware Version")
bfa was not updated. I presume this was an oversight but it broke support
for bfa+bna cards such as the following
04:00.0 Fibre Channel [0c04]: Brocade Communications Systems, Inc.
1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
04:00.1 Fibre Channel [0c04]: Brocade Communications Systems, Inc.
1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
04:00.2 Ethernet controller [0200]: Brocade Communications Systems,
Inc. 1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
04:00.3 Ethernet controller [0200]: Brocade Communications Systems,
Inc. 1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
Currently, if the bfa module is loaded first, bna fails to probe the
respective devices with
[ 215.026787] bna: QLogic BR-series 10G Ethernet driver - version: 3.2.25.1
[ 215.043707] bna 0000:04:00.2: bar0 mapped to ffffc90001fc0000, len 262144
[ 215.060656] bna 0000:04:00.2: initialization failed err=1
[ 215.073893] bna 0000:04:00.3: bar0 mapped to ffffc90002040000, len 262144
[ 215.090644] bna 0000:04:00.3: initialization failed err=1
Whereas if bna is loaded first, bfa fails with
[ 249.592109] QLogic BR-series BFA FC/FCOE SCSI driver - version: 3.2.25.0
[ 249.610738] bfa 0000:04:00.0: Running firmware version is incompatible with the driver version
[ 249.833513] bfa 0000:04:00.0: bfa init failed
[ 249.833919] scsi host6: QLogic BR-series FC/FCOE Adapter, hwpath: 0000:04:00.0 driver: 3.2.25.0
[ 249.841446] bfa 0000:04:00.1: Running firmware version is incompatible with the driver version
[ 250.045449] bfa 0000:04:00.1: bfa init failed
[ 250.045962] scsi host7: QLogic BR-series FC/FCOE Adapter, hwpath: 0000:04:00.1 driver: 3.2.25.0
Increase bfa's requested firmware version. Also increase the driver
version. I only tested that all of the devices probe without error.
Reported-by: Tim Ehlers <tehlers@gwdg.de>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Rasesh Mody <rasesh.mody@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a call to mempool_create_slab_pool() in snic_probe() returns NULL,
return -ENOMEM to indicate failure. mempool_creat_slab_pool() only fails
if it cannot allocate memory.
https://bugzilla.kernel.org/show_bug.cgi?id=189061
Reported-by: bianpan2010@ruc.edu.cn
Signed-off-by: Burak Ok <burak-kernel@bur0k.de>
Signed-off-by: Andreas Schaertl <andreas.schaertl@fau.de>
Acked-by: Narsimhulu Musini <nmusini@cisco.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This fix is to avoid calling fnic_fw_reset_handler through
fnic_host_reset when a finc reset is alreay in progress.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix build of SCSI qedi driver. It uses uio interfaces so it should
depend on UIO.
ERROR: "uio_unregister_device" [drivers/scsi/qedi/qedi.ko] undefined!
ERROR: "uio_event_notify" [drivers/scsi/qedi/qedi.ko] undefined!
ERROR: "__uio_register_device" [drivers/scsi/qedi/qedi.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: QLogic-Storage-Upstream@cavium.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ensure that if scsi-mq is enabled that scsi_internal_device_block()
waits until ongoing shost->hostt->queuecommand() calls have finished.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Ledford <dledford@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A race between scanning and fc_remote_port_delete() may result in a
permanent stop if the device gets blocked before scsi_sysfs_add_sdev()
and unblocked after. The reason is that blocking a device sets both the
SDEV_BLOCKED state and the QUEUE_FLAG_STOPPED. However,
scsi_sysfs_add_sdev() unconditionally sets SDEV_RUNNING which causes the
device to be ignored by scsi_target_unblock() and thus never have its
QUEUE_FLAG_STOPPED cleared leading to a device which is apparently
running but has a stopped queue.
We actually have two places where SDEV_RUNNING is set: once in
scsi_add_lun() which respects the blocked flag and once in
scsi_sysfs_add_sdev() which doesn't. Since the second set is entirely
spurious, simply remove it to fix the problem.
Cc: <stable@vger.kernel.org>
Reported-by: Zengxi Chen <chenzengxi@huawei.com>
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for request iopriority handling in the mpt3sas
layer. This works only when a ATA device is behind the SATL. The ATA
device also has to indicate that it supports command priorities in the
identify information that is pulled from the SATL.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Fix race condition between dpc_thread accessing Multiqueue resources
and qla2x00_remove_one thread trying to free resource.
- Fix out of order free for Multiqueue resources. Also, Multiqueue
interrupts needs a workqueue. Interrupt needed to stop before
the wq can be destroyed.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tell the SCSI layer how many hardware queues we have based on the number
of max queue pairs created. The number of max queue pairs created will
depend on number of MSI-X vector count.
This feature can be turned on via CONFIG_SCSI_MQ_DEFAULT or passing
scsi_mod.use_blk_mq=Y as a parameter to the kernel
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaced existing multiple queue functionality with framework
that allows for the creation of pairs of request and response queues,
either at start of day or dynamically.
Queue pair creation depend on module parameter "ql2xmqsupport",
which need to be enabled to create queue pair.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaces the old pci_enable_msi[x]* and pci_disable_msi[x] calls.
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is allowing only ROM mailbox command which are
necessary to initialize chip after a reset has been issued.
In a target environment, there could be a user space daemon
which can issue statistics and other management mailbox command
which are non-critical. This patch will timeout non critical
mailbox commands immediately rather than waiting for timeout,
if driver detects that chip reset has been issued or chip reset
is in progress.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch cleanup warning reported by checkpatch.pl WARNING: Possible
unnecessary 'out of memory' message With no available memory, a warn on
message already gets printed by page alloc apis and modified goto use if
memory unallocated.
Signed-off-by: Amit Kushwaha <kushwaha.a@samsung.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change updates the 3ware drivers (3w-xxxx, 3w-9xxx, 3w-sas) email
addresses from linuxraid@lsi.com to aradford@gmail.com, since the old
email address doesn't exist.
This patch was updated to remove www.lsi.com text.
[mkp: applied by hand]
Signed-off-by: Adam Radford <aradford@gmail.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do not post hw active open cmd if IFF_UP is not set or link is down on
the interface, return -ENETDOWN in this case.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add module_put() in cxgbi_sock_act_open_req_arp_failure() to release
module reference in case of arp failure, also check return value of
try_module_get() before posting active open hw cmd.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
T6 adapters reduce number of completions to host by generating single
completion for all the directly placed(DDP) iSCSI pdus in a sequence.
This patch adds new structure for completion hw cmd (struct
cpl_rx_iscsi_cmp) and implements T6 completion feature.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add T6 active open cmd to open active connections on T6 adapters.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cxgb4_tp_smt_idx() is defined in cxgb4 driver, it returns smt_idx for
T4,T5,T6 adapters.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The QLogic FastLinQ Driver for iSCSI (qedi) is the iSCSI specific module
for 41000 Series Converged Network Adapters by QLogic.
This patch consists of following changes:
- MAINTAINERS Makefile and Kconfig changes for qedi,
- PCI driver registration,
- iSCSI host level initialization,
- Debugfs and log level infrastructure.
The following indiviual changes are merged into this commit:
qedi: Add LL2 iSCSI interface for offload iSCSI.
qedi: Add support for iSCSI session management.
qedi: Add support for data path.
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@cavium.com>
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJYT5HMAAoJELDendYovxMvhNQH/1g/3ahM4JKN8Z0SbjKBEdQm
yj2xOj6cE3l6wMSUblKjZD2DLLhpmcHT/E97Xro/lZQEfQJoMXXWWDFowMU/P1LA
mJxb7Fzq5Wr+6eGSAlIQB270MrpNi/luf+CWHMwVA3V7R3KRXwonOdGQSkISIzCd
tgIydEA3a9r2+HgeIBpZFZ4GcSrJQU75krMyl2tjD1C+jeYVd+zdoj2OnDsZQDZQ
hDWApMpNbpSBAn7JtSSdXWSTBsGH0lUECebeYPhPQ2sX2P6Y8+UCGwA7i6FFdbTa
agXfVSdRz8dCe3k19VcKDAw6nK9BTTMnEeEHmkmygIh6wuHPP44CzigTXIbJoXI=
=zjfm
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen features and fixes for 4.10
These are some fixes, a move of some arm related headers to share them
between arm and arm64 and a series introducing a helper to make code
more readable.
The most notable change is David stepping down as maintainer of the
Xen hypervisor interface. This results in me sending you the pull
requests for Xen related code from now on"
* tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (29 commits)
xen/balloon: Only mark a page as managed when it is released
xenbus: fix deadlock on writes to /proc/xen/xenbus
xen/scsifront: don't request a slot on the ring until request is ready
xen/x86: Increase xen_e820_map to E820_X_MAX possible entries
x86: Make E820_X_MAX unconditionally larger than E820MAX
xen/pci: Bubble up error and fix description.
xen: xenbus: set error code on failure
xen: set error code on failures
arm/xen: Use alloc_percpu rather than __alloc_percpu
arm/arm64: xen: Move shared architecture headers to include/xen/arm
xen/events: use xen_vcpu_id mapping for EVTCHNOP_status
xen/gntdev: Use VM_MIXEDMAP instead of VM_IO to avoid NUMA balancing
xen-scsifront: Add a missing call to kfree
MAINTAINERS: update XEN HYPERVISOR INTERFACE
xenfs: Use proc_create_mount_point() to create /proc/xen
xen-platform: use builtin_pci_driver
xen-netback: fix error handling output
xen: make use of xenbus_read_unsigned() in xenbus
xen: make use of xenbus_read_unsigned() in xen-pciback
xen: make use of xenbus_read_unsigned() in xen-fbfront
...
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
Instead of allocating a single unused biovec for discard requests, send
them down without any payload. Instead we allow the driver to add a
"special" payload using a biovec embedded into struct request (unioned
over other fields never used while in the driver), and overloading
the number of segments for this case.
This has a couple of advantages:
- we don't have to allocate the bio_vec
- the amount of special casing for discard requests in the block
layer is significantly reduced
- using this same scheme for other request types is trivial,
which will be important for implementing the new WRITE_ZEROES
op on devices where it actually requires a payload (e.g. SCSI)
- we can get rid of playing games with the request length, as
we'll never touch it and completions will work just fine
- it will allow us to support ranged discard operations in the
future by merging non-contiguous discard bios into a single
request
- last but not least it removes a lot of code
This patch is the common base for my WIP series for ranges discards and to
remove discard_zeroes_data in favor of always using REQ_OP_WRITE_ZEROES,
so it would be good to get it in quickly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of requesting a new slot on the ring to the backend early, do
so only after all has been setup for the request to be sent. This
makes error handling easier as we don't need to undo the request id
allocation and ring slot allocation.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
One small fix for a regression in a prior fix (again). This time the
condition in the prior fix BUG_ON proved to be wrong under certain
circumstances causing a BUG to trigger where it shouldn't in the lpfc
driver.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cyir
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One small fix for a regression in a prior fix (again).
This time the condition in the prior fix BUG_ON proved to be wrong
under certain circumstances causing a BUG to trigger where it
shouldn't in the lpfc driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: fix oops/BUG in lpfc_sli_ringtxcmpl_put()
And simplify the MSI-X logic in general - just request the two vectors
directly instead of going through an indirection table.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the hip06 and hip07 SoCs, the interrupt lines from the SAS
controllers are connected to mbigen hw module [1]. The mbigen module is
probed with module_init, and, as such, is not guaranteed to probe before
the SAS driver. So we need to support deferred probe.
We check for probe deferral in the hw layer probe, so we not probe into
the main layer and allocate shost, memories, etc., to later learn that
we need to defer the probe.
[1] ./Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[mkp: fixed bad indentation]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NetApp did confirm this is not required.
Cc: Martin George <Martin.George@netapp.com>
Cc: Robert Stankey <Robert.Stankey@netapp.com>
Cc: Steven Schremmer <Steven.Schremmer@netapp.com>
Cc: Sean Stewart <Sean.Stewart@netapp.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christophe Varoqui <christophe.varoqui@opensvc.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Cc: device-mapper development <dm-devel@redhat.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Reviewed-by: Sean Stewart <sean.stewart@netapp.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable ret is reset in the loop, and its value will be 0 during the
second and after repeat of the loop. If pci_alloc_consistent() returns a
NULL pointer then, it will leaves with return value 0. 0 means no error,
which is contrary to the fact. This patches fixes the bug, explicitly
assigning "-ENOMEM" to return variable ret on the path that the call to
pci_alloc_consistent() fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188951
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jitendra Bhivare <Jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable ret is reset in the loop, and its value will be 0 during the
second and after repeat of the loop. If pci_alloc_consistent() returns a
NULL pointer then, it will leaves with return value 0. 0 means no error,
which is contrary to the fact. This patches fixes the bug, explicitly
assigning "-ENOMEM" to return variable ret on the path that the call to
pci_alloc_consistent() fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188941
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jitendra Bhivare <Jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Older SmartArray controllers (eg SmartArray 64xx) do not support the
extended REPORT PHYS command, so fallback to use the legacy version
here.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that sparse complains about RCU pointer dereferences.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: tang.junhui <tang.junhui@zte.com.cn>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Passing one instead of 8 or 16 arguments reduces the size of the
generated code somewhat:
add/remove: 2/3 grow/shrink: 1/4 up/down: 1772/-2137 (-365)
There's one more candidate, unique_id_show, but that uses %02X, and I'm
not sure it would be ok to start using lowercase there, so I've left it
alone for now.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
