The Raspberry Pi 3 A+ is similar to the Pi 3 B+ but has only 512 MB RAM,
1 USB 2.0 port and no Ethernet.
Compared to the Raspberry Pi 3 B it isn't possible to control BT_ON and
WL_ON separately.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
This patch adds all SPI instances of the STM32F429 SoC.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This router has BCM4709C0 SoC, 128 MiB NAND flash (MX30LF1G18AC-TI),
512 MiB memory and 3 x LAN and 1 x WAN ports. WiFi chips are
BCM4366C0 x 2. The router has a small LCD and 3 capactive keys driven by
a PIC microcontroller, which is in turn wired to UART1 of main board.
Signed-off-by: Hao Dong <halbertdong@gmail.com>
[rmilecki: drop chosen { }, fix whitespaces, update commit message]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Couple of simple changes to add dynamic-power-coefficient information
for CPUs on TC2 and fix tuple used for uart and mmci interrupts with
lists.
-----BEGIN PGP SIGNATURE-----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=Zh3V
-----END PGP SIGNATURE-----
Merge tag 'vexpress-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv7 Vexpress updates for v5.1
Couple of simple changes to add dynamic-power-coefficient information
for CPUs on TC2 and fix tuple used for uart and mmci interrupts with
lists.
* tag 'vexpress-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm: dts: vexpress-v2p-ca15_a7: Add cpu dynamic-power-coefficient information
ARM: dts: vexpress: use list instead of tuple for mmci interrupts
ARM: dts: mps2: use list instead of tuple for uart interrupts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As usual, this is a random assortment of changes:
- ARM PMU is enabled on the A10
- The first usage of the PIO pinbank regulator supplies added,
for the Bananapi
- Broadcom-based Bluetooth enabled on the Bananapi M2 Magic and M2
Ultra, using the serdev bindings
- Video codec added for the A10
- Display pipeline for the A23 added and enabled for the generic Q8
tablets
-----BEGIN PGP SIGNATURE-----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=WU3N
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT changes for 5.1
As usual, this is a random assortment of changes:
- ARM PMU is enabled on the A10
- The first usage of the PIO pinbank regulator supplies added,
for the Bananapi
- Broadcom-based Bluetooth enabled on the Bananapi M2 Magic and M2
Ultra, using the serdev bindings
- Video codec added for the A10
- Display pipeline for the A23 added and enabled for the generic Q8
tablets
* tag 'sunxi-dt-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i-a23-q8: Set compatible string for LCD panel
ARM: dts: sun8i-q8-common: Enable display pipeline with RGB LCD panel
ARM: dts: sun8i-a23: Add compatible strings to display pipeline device nodes
ARM: dts: sun8i-a33: Move display pipeline nodes to a23/a33 common dtsi
ARM: dts: sun8i-a23-a33: Move NAND controller device node to sort by address
ARM: dts: sun4i-a10: Add Video Engine and reserved memory nodes
ARM: dts: sun4i: Add support for the C1 SRAM region with the SRAM controller
ARM: dts: sunxi: bananapi-m2-plus: Add Bluetooth device node
ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix WiFi regulator definitions
ARM: dts: sun8i: r40: Add pinmux setting for CLK_OUT_A
ARM: dts: sun8i: r40: Add pinmux settings for UART3 on PG pingroup
ARM: dts: sun7i: bananapi: Add GPIO banks regulators
ARM: dts: sun4i-a10: Add PMU node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
tree nodes required by the DRM driver.
-----BEGIN PGP SIGNATURE-----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=ezF7
-----END PGP SIGNATURE-----
Merge tag 'integrator-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
This updates the Integrator DTS files with the device
tree nodes required by the DRM driver.
* tag 'integrator-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Augment panel setting for Integrator/CP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
nodes to the Nomadik NHK8815.
-----BEGIN PGP SIGNATURE-----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=PIyf
-----END PGP SIGNATURE-----
Merge tag 'nomadik-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
This add the new display driver and DRM driver device
nodes to the Nomadik NHK8815.
* tag 'nomadik-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: nomadik: Augment NHK15 panel setting
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
-MPU STM32MP157 platform update:
-Declare DMAs for timers
-Add sleep support for CAN
-Split CAN RAM mapping between the 2 FDCAN instances
-Add support of thermal sensor (DTS)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=660S
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v4.21, round 1
Highlights:
----------
-MPU STM32MP157 platform update:
-Declare DMAs for timers
-Add sleep support for CAN
-Split CAN RAM mapping between the 2 FDCAN instances
-Add support of thermal sensor (DTS)
* tag 'stm32-dt-for-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: add thermal sensor support on STM32MP157c
ARM: dts: stm32: add can1 sleep pins muxing on stm32mp157c-ev1 board
ARM: dts: stm32: add can1 sleep pins muxing
ARM: dts: stm32: change CAN RAM mapping on stm32mp157c
ARM: dts: stm32: don't use timers dmas on stm32mp157c-ev1
ARM: dts: stm32: don't use timers dmas on stm32mp157c-ed1
ARM: dts: stm32: Add dmas to timer on stm32mp157c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the uart1 node such that the clock will be enabled.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the lpc_ctrl node in the quanta-q71l dts such that the LPC_CLK is
enabled.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added uart2 and uart3 in Facebook Tiogapass for routing serial input
from Host to BMC for SoL via LPC.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added lpc control for enabling lpc clock and lpc snoop devices to
Facebook Tiogapass device tree.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add reset property for dma, can and sdram on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
A CPUfreq driver, like the ARM big.LITTLE driver used on the TC2 board,
which provide the Energy Model with power cost information via the
PM_OPP of_dev_pm_opp_get_cpu_power() function, do need the
dynamic-power-coefficient (C) in the device tree.
Method used to obtain the C value:
C is computed by measuring energy (E) consumption of a frequency domain
(FD) over a 10s runtime (t) sysbench workload running at each Operating
Performance Point (OPP) affine to 1 or 2 CPUs of that FD while the other
CPUs of the system are hotplugged out.
By definition all CPUs of a FD have the the same micro-architecture. An
OPP is characterized by a certain frequency (f) and voltage (V) value.
The corresponding power values (P) are calculated by dividing the delta
of the E values between the runs with 2 and 1 CPUs by t.
With n data tuples (P, f, V), n equal to number of OPPs for this
frequency domain, we can solve C by:
P = Pstat + Pdyn
P = Pstat + CV²f
Cx = (Px - P1)/(Vx²fx - V1²f1) with x = {2, ..., n}
The C value is the arithmetic mean out of {C2, ..., Cn}.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The compatible string for the LCD panel used for the Q8 tablets are just
a placeholder that was shown to be compatible with the actual panels
found on these devices. The real panels do not have any identifiable
markings and vary between production runs.
The compatibe string previously used had a pixel clock that could not
be accurately reproduced on Allwinner hardware, and discussions on
whether a margin should be added to the display drivers and how large
a margin was acceptable had stalled.
Now that we have a panel model that is actually used with Allwinner
hardware, has the same dimensions, and the timings have been shown to
work with the nameless panels, we can use that one instead.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A13 Q8 tablet, following the A13 reference tablet design, has the
system's fixed 3.3V rail feed the VCC supply of the LCD panel.
Additional voltage rails used by the panel are generated using a
regulator fed from the unregulated IPSOUT output of the PMIC. The latter
is unrepresentable in the device tree. Both are controlled with MOSFETs
by the enable GPIO added in the previous patch. The actual enable or
reset pin for the panel is tied directly to LCD-VCC after the MOSFET.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the AXP209 GPIOs, we can toggle the LCD panel enable
line. Add the GPIO phandle to the panel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The panel backlight and enable GPIO comments were incorrectly placed
in the input port, while it should have been in the panel node itself.
Move them to the correct position.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the GPIOs on the AXP209, we can control the LCD
backlight with them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The mmc.txt didn't explicitly say disable-wp is for SD card slot
only, but that is what it was designed for in the first place.
Remove all disable-wp from emmc or sdio controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The change removes redundant #address-cells and #size-cells properties from
gpio-keys-polled compatible device nodes found in lpc4357-ea4357-devkit and
lpc4350-hitex-eval board DTS files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Commit 225da7e65a ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7c ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org>
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 225da7e65a ("ARM: dts: add eMMC reset line for exynos4412-odroid-common")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Q8 tablets follow the A23/A33 tablet reference design, and normally
use a "generic" 800x480 LCD panel. The actual panel may vary between
production runs, and there are no visible markings denoting its model.
This patch uses a panel that has the same dimensions and timings that
are close to what was provided in the vendor fex files.
Since there are also A33 Q8 tablets with 1024x600 panels, this patch
only sets the compatible string for A23 Q8 tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Q8 design for A23/A33 tablets have an 18-bit RGB LCD panel connected
to the LCD interface on the SoC, the DC1SW output on the PMIC providing
power for the LCD, and PH7 toggling the reset pin for the panel.
This patch adds a device node for the panel, describing the above, and
enables the display pipeline.
The actual model or compatible string for the panel should be added in
the tablet device tree file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that the compatible strings for the display pipeline on the A23 have
been added to the bindings, add the corresponding compatibles to the
device nodes already in the A23/A33 shared dtsi.
While the A23 has the TCON ch1 clock defined in the CCU, and the channel
1 registers are available, it does not have any means to use channel 1
due to a lack of downstream encoders, and the enable bit for channel 1 is
hard-wired to 0 (off). Hence the ch1 clock is left out.
As the MIPI DSI output device is not officially documented, and there
are no reference devices to test it, it is not covered by this patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The display pipeline has the same structure, resources and connections
on both the A23 and A33. The differences include:
- compatible strings
- extra clock, reset control, and IO region for SAT in the backend
only found on the A33
- missing ch1 clock for the TCON
However, while the A23 has the TCON ch1 clock defined in the CCU, and
the channel 1 registers are available, it does not have any means to
use channel 1 due to a lack of downstream encoders, and the enable bit
for channel 1 is hard-wired to 0 (off).
As the MIPI DSI output device is not officially documented, and there
are no A23 reference devices to test it, it is not covered by this
patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The NAND controller device node was inserted into the wrong position,
probably due to a rebase or merge, as the file's structure does not
provide enough context for git to accurately match the previous device
node block.
Fixes: d7b843df13 ("ARM: dts: sun8i: add NAND controller node for A23/A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is an ARM + FPGA instrumentation board used at telescopes in
Antarctica, Chile, and Canada:
https://pole.uchicago.edu/https://arxiv.org/abs/1608.03025https://chime-experiment.ca/
With these commits and a suitable userspace, we can boot the board, load
a FPGA bitstream, and communicate with the RTL design. Most of the board's
telemetry sensors (temperatures, voltages) are functional but detailed
testing is to follow.
We are weaning ourselves off TI's "official" kernel for this SOC, which
has been stuck at 2.6.37 and is not really fit for use. To anyone at TI:
despite good silicon and some dedicated support enginers, your
open-source software strategy for these parts has not worked well.
Please get in touch with me if you'd like to have a constructive
discussion about ways to improve it.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: dropped fpga@1 as linux,spidev is still undocumented]
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO3/4 and MCSPI2/3/4 are now present. Lightly tested on am3874
platform.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: split to apply hwmod and dts changes separately]
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO3/4 and MCSPI2/3/4 are now present. Lightly tested on am3874
platform.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: split to apply hwmod and dts changes separately]
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no functional change here; the I2C and ELM entries leaked
into each other and this separates them again.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ethernet works in kernel only if we use some binary u-boot from the
past which have support for KS8851.
The u-boot sources are not available for this mysterious u-boot image
people tends to hold on... Mainline u-bott does not have ethernet support
for sdp4430 and if we use that the ethernet is not working.
After some debugging I have managed to get the ethernet working with
mainline u-boot while not breaking the networking with the case when we
boot with the mysterious binary u-boot.
Basically we were missing bunch of pinmux settings and the 'magic'
gpio_138 handling in kernel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the legacy "linux,wakeup" boolean property is already replaced
with "wakeup-source". However few occurrences of old property has popped
up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source" property
introduced in the commit aeda5003d0 ("Input: matrix_keypad - change
name of wakeup property to "wakeup-source"")
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the unnecessary properties #address-cells and #size-cells
of node pinmux as there are no child-nodes with property reg.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CSI controller found on the H3 (and H5) is a reduced version of the
one found on the A31. It only has 1 channel, instead of 4 channels for
time-multiplexed BT.656. Since the H3 is a reduced version, it cannot
"fallback" to a compatible that implements more features than it
supports.
Drop the A31 fallback compatible.
Fixes: f89120b6f5 ("ARM: dts: sun8i: Add the H3/H5 CSI controller")
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Xen-swiotlb hooks into the arm/arm64 arch code through a copy of the DMA
DMA mapping operations stored in the struct device arch data.
Switching arm64 to use the direct calls for the merged DMA direct /
swiotlb code broke this scheme. Replace the indirect calls with
direct-calls in xen-swiotlb as well to fix this problem.
Fixes: 356da6d0cd ("dma-mapping: bypass indirect calls for dma-direct")
Reported-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
This patch enable HDMI output on sun8i-h3-nanopi-m1-plus.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add support for Renesas RZ/A2M evaluation board.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the RZ/A2 (R7S9210) SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the device tree bindings for USB OTG support. Driver was tested
using on a LG Nexus 5 (hammerhead) phone. This patch is based on work
from Jonathan Marek and from the other msm8974 devices.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the gpio-ranges property to pm8941_gpios so that the GPIO
pins are initialized by the GPIO framework and not pinctrl. This fixes
a circular dependency so GPIO hogging can be used on this board.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds WiFi support to the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[masneyb@onstation.org: Enabled wlan_regulator_pin and wlan_sleep_clk_pin]
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
All the GSBI blocks are marking their GIC IRQ lines as
"IRQ_TYPE_NONE" but there is no such thing: all GIC IRQ
lines have a trigger type.
That yields the following warning from the GIC driver:
WARNING: CPU: 0 PID: 1 at ../drivers/irqchip/irq-gic.c:1016
gic_irq_domain_translate+0xdc/0xe4
(...)
Mark all of these IRQ_TYPE_LEVEL_HIGH as is common so this
warning goes away.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The GSBI module complains:
gsbi 16500000.gsbi: missing mode configuration
gsbi: probe of 16500000.gsbi failed with error -22
gsbi 16600000.gsbi: missing mode configuration
gsbi: probe of 16600000.gsbi failed with error -22
gsbi 19800000.gsbi: GSBI port protocol: 2 crci: 0
So we should mark these GSBIs as "disabled" in the SoC
file by default.
If boards appear that make use of them, we can simply
set status = "ok" in the DTS for them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Vexpress motherboard MMCI requires dedicated interrupts for CMD and PIO,
which obviously should be expressed as a list. Current form uses tuple
and it works fine since interrupt-cells equal to 1.
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
MPS2 UART requires dedicated interrupts for RX, TX and overflow, which
obviously should be expressed as a list. Current form uses tuple and
it has worked so far because NVIC has interrupt-cells equal to 1.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Inspur on5263m5 is an Intel Xeon OCP server that uses the ASPEED
AST2500 BMC.
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
[joel: Rework commit message]
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds nodes for the Video Engine and the associated reserved memory
for the A10. Up to 96 MiB of memory are dedicated to the CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for the A10 platform. The region is shared
between the Video Engine and the CPU.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Based on Rev. 1.00 of the R-Car H1 datasheet.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Added ADC and other sensor devices present in the Facebook Tiogapass
machine.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the description of the four Keyboard Controller Style (KCS)
IPMI communication channels present in the ASPEED BMC. They are disabled
by default.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Allows the GPIO controller to be used as an interrupt parent.
of_irq_find_parent() skips interrupt controller nodes that do
not have the #interrupt-cells property.
Signed-off-by: Mark Walton <mark.walton@serialtek.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add Delta Electronics power supply DPS-650-AB.
Signed-off-by: Xiaoting Liu <xiaoting.liu@hxt-semitech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add reset property for gpio, i2c, sdmmc, nand, qspi, spi, uart, and
watchdog on base socfpga and socfpga_arria10.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This matches licensing used by other BCM53573 files and BCM5301X.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds missing deassert functionality to the ARC HSDK reset driver,
fixes some indentation and grammar issues in the kernel docs, adds a
helper to count the number of resets on a device for the non-DT case
as well, adds an early reset driver for SoCFPGA and simple reset driver
support for Stratix10, and generalizes the uniphier USB3 glue layer
reset to also cover AHCI.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCXDTOiBcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwMnMAP9u9pJr0g6t/8NwiDNQGYIupFMQ
vH3hIUP7pwkELeN36AEAuFJG66r1Y96icDQCLn9x6vxwgTDmJGgGHM3CWEftsQI=
=vFwq
-----END PGP SIGNATURE-----
Merge tag 'reset-for-5.0-rc2' of git://git.pengutronix.de/git/pza/linux into fixes
Late reset controller changes for v5.0
This adds missing deassert functionality to the ARC HSDK reset driver,
fixes some indentation and grammar issues in the kernel docs, adds a
helper to count the number of resets on a device for the non-DT case
as well, adds an early reset driver for SoCFPGA and simple reset driver
support for Stratix10, and generalizes the uniphier USB3 glue layer
reset to also cover AHCI.
* tag 'reset-for-5.0-rc2' of git://git.pengutronix.de/git/pza/linux:
reset: uniphier-glue: Add AHCI reset control support in glue layer
dt-bindings: reset: uniphier: Add AHCI core reset description
reset: uniphier-usb3: Rename to reset-uniphier-glue
dt-bindings: reset: uniphier: Replace the expression of USB3 with generic peripherals
ARM: socfpga: dts: document "altr,stratix10-rst-mgr" binding
reset: socfpga: add an early reset driver for SoCFPGA
reset: fix null pointer dereference on dev by dev_name
reset: Add reset_control_get_count()
reset: Improve reset controller kernel docs
ARC: HSDK: improve reset driver
Signed-off-by: Olof Johansson <olof@lixom.net>
They are all device tree fixes which also worth being in stable:
- Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
this area and crashing while doing it.
- Use correct PCIe reset signal on MACCHIATOBin (Armada 8040 based)
- Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXDjK7AAKCRALBhiOFHI7
1eZfAJ0X/MrjG/MB1NSlJ2kUGmBs5MnnswCdFZpNF4okkjtwyWoCoBsp9X3kUkw=
=vYNz
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 5.0
They are all device tree fixes which also worth being in stable:
- Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
this area and crashing while doing it.
- Use correct PCIe reset signal on MACCHIATOBin (Armada 8040 based)
- Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)
* tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: Fix polarity of GPIO fan lines
arm64: dts: marvell: mcbin: fix PCIe reset signal
arm64: dts: marvell: armada-ap806: reserve PSCI area
Signed-off-by: Olof Johansson <olof@lixom.net>
- Handle failed allocations in the IM/PC bus attachment.
- Use struct_size() for allocation.
-----BEGIN PGP SIGNATURE-----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=KT88
-----END PGP SIGNATURE-----
Merge tag 'integrator-fixes-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into fixes
Fixes for the Integrator:
- Handle failed allocations in the IM/PC bus attachment.
- Use struct_size() for allocation.
* tag 'integrator-fixes-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: impd1: use struct_size() in devm_kzalloc()
gpio: pl061: handle failed allocations
Signed-off-by: Olof Johansson <olof@lixom.net>
rv1108-elgin-r1 board is based on Rockchip RV1108 SoC.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the pin settings for the SPI pins so they can be used across
multiple boards.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pass the 'dma-names' property to the SPI ports so that DMA can
be supported.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds the core display subsystem and vop nodes to rk3066.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NHK15 panel is specified inside the display controller,
which works for the DPI-type DT parsing the old fbdev code
used, but for the DRM driver it needs to be spawn as its own
device, so we move it out of the display controller.
We also drop the panel timings: this should be determined
by the hardware or a device-specific compatible string, not
by this type of encoding into the device tree. It turns out
that this hardware is strapped to the right configuration
at boot already and we the driver just reads out the
hardware-specified resolution and timings. Drop the
"panel,dpi" compatible string altogether.
Fix a comment error in the DTS file while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
LDO20 regulator provides power for the MMC card on Odroid U3 boards. That
regulator has been marked as 'boot-on' since the beginning of Odroid X/U3
support, but such flag is not really needed for it. That regulator is
correctly described as supply for eMMC card and controlled by its driver.
Commit 05f224ca66 ("regulator: core: Clean enabling always-on regulators
+ their supplies") changed the way the boot-on regulators are handled and
since then regulators marked as 'boot-on' got increased reference count
and are not turned off for the system suspend time.
The new approach turned out to break suspend/resume support on Odroid U3
with eMMC card, because the card is not properly shutdown due to missing
of power cycle. Fix this by removing excessive 'boot-on' flag and let
MMC driver to control turning power on and off.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Bindings of the fixed-regulator, which precedes support for GPIO flags
passed via phandle descriptor, introduced its own method annotating
that the given GPIO line is active low or high - by using
'enable-active-high' property. The driver always ignored flags passed
via GPIO descriptor.
Fix the conflicting GPIO flags to match the status forced by the
'enable-active-high' property to avoid future confusion.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix the DTC warning for xti node:
arch/arm/boot/dts/s3c2416-smdk2416.dts:23.12-28.5:
Warning (simple_bus_reg): /clocks/xti: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
According to Devicetree specification, the unit-address must match the
first address specified in the reg property of the node. Fix the DTC
warning onenand node:
arch/arm/boot/dts/s5pv210.dtsi:81.29-93.5:
Warning (simple_bus_reg): /soc/onenand@b0000000: simple-bus unit address format error, expected "b0600000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
This commit adds DMC (Dynamic Memory Controller) nodes, which are needed
by S5Pv210 cpufreq driver to work.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This commit enables following devices present on Aries based phones:
- pwm-vibrator attached to PWM 1
- poweroff support
- Atmel maXTouch touchscreen, connected to I2C-2
- Broadcom BCM4329 Bluetooth over UART-0
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
THis commit adds memory reservation required by MFC (Multi Format Codec)
to run. On S5PV210 both regions needs to be on separate memory banks.
Size of both regions is taken from vendor Linux kernel sources.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
devm_kzalloc(), devm_kstrdup() and devm_kasprintf() all can
fail internal allocation and return NULL. Using any of the assigned
objects without checking is not safe. As this is early in the boot
phase and these allocations really should not fail, any failure here
is probably an indication of a more serious issue so it makes little
sense to try and rollback the previous allocated resources or try to
continue; but rather the probe function is simply exited with -ENOMEM.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 684284b64a ("ARM: integrator: add MMCI device to IM-PD1")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These two lines are active high, not active low. The bug was
found when we changed the kernel to respect the polarity defined
in the device tree.
Fixes: 1b90e06b14 ("ARM: kirkwood: Use devicetree to define DNS-32[05] fan")
Cc: Jamie Lentin <jm@lentin.co.uk>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Julien D'Ascenzio <jdascenzio@posteo.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Reported-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Tested-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds the actual VGA DAC bridge that is used in the
Versatile AB, and sets the mode to 640x480 VGA and
routes the CLCD pads appropriately.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To avoid the following error:
asoc-simple-card sound: ASoC: Failed to create card debugfs directory
Which is because the card name contains '/' character, which can not be
used in file or directory names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add the board level fixed regulators for 3.3V and 1.8V which is used to
power - among other things - the tlv320aic3106 codec.
Apart from removing the following warning during boot:
tlv320aic3x-codec 0-0018: Invalid supply voltage(s) AVDD: -22, DVDD: -22
With the correct voltages the driver can select correct OCMV value to
reduce pop noise.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
To avoid the following error:
asoc-simple-card sound: ASoC: Failed to create card debugfs directory
Which is because the card name contains '/' character, which can not be
used in file or directory names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add the board level fixed regulators for 3.3V and 1.8V which is used to
power - among other things - the tlv320aic3106 codec.
Apart from removing the following warning during boot:
tlv320aic3x-codec 0-0018: Too high supply voltage(s) AVDD: 5000000, DVDD: 5000000
With the correct voltages the driver can select correct OCMV value to
reduce pop noise.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") the gpiochip label no longer has an ID
suffix. Update the GPIO lookup entries.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") the gpiochip label no longer has an ID
suffix. Update the GPIO lookup entries.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") the gpiochip label no longer has an ID
suffix. Update the GPIO lookup entries.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") the gpiochip label no longer has an ID
suffix. Update the GPIO lookup entries.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") the gpiochip label no longer has an ID
suffix. Update the GPIO lookup entries.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add devicetree support for 96Boards Chameleon96 board from Novtech, Inc.
based on Altera CycloneV SoC FPGA. This board is one of the Consumer
Edition boards of the 96Boards family and has the following key features:
* SoC - Intel Cyclone V SoC FPGA
* GPU - Graphics based on Intel Video Suite for FPGA
* RAM - 512MB DDR3L
* USB - 2x USB2.0 Host, 1x USB2.0 OTG
* Wireless - Wifi, BT
More information about this board can be found in 96Boards product
page: https://www.96boards.org/product/chameleon96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART1 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, the board's
fixed 3.3V power regulator provides overall power via VBAT and I/O power
via VDDIO. The RTC clock output from the SoC provides the LPO low power
clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART3 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO1 and
DLDO2 regulator outputs from the PMIC provide overall power via VBAT and
I/O power via VDDIO. The CLK_OUT_A clock output from the SoC provides
the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
The LPO clock is fed from CLK_OUT_A, which needs to be muxed on pin
PI12. This can be represented in multiple ways. This patch puts the
pinctrl property in the pin controller node. This is due to limitations
in Linux, where pinmux settings, even the same one, can not be shared
by multiple devices. Thus we cannot put it in both the WiFi and
Bluetooth device nodes. Putting it the CCU node is another option, but
Linux's CCU driver does not handle pinctrl. Also the pin controller is
guaranteed to be initialized after the CCU, when clocks are available.
And any other devices that use muxed pins are guaranteed to be
initialized after the pin controller. Thus having the CLK_OUT_A pinmux
reference be in the pin controller node is a good choice without having
to deal with implementation issues.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The design of the Bananapi M2 Ultra has both DLDO1 and DLDO2 regulators
provide power to the WiFi+BT module, which is based on the Broadcom
BCM43438 or BCM43430 chip. Each regulator output from the PMIC can supply
up to 200 mA. The datasheet of the chip suggests a maximum power draw of
up to 360 mA when transmitting, thus requiring two outputs from the PMIC
to handle the load. However the device tree only references one of them,
leaving the other unused and possibly turned off.
This patch marks both as always-on, since we don't have a proper binding
to specify two regulators as "bound together". The name and constraints
of DLDO2 are also added.
Fixes: da7ac948fa ("ARM: dts: sun8i: Add board dts file for Banana Pi M2
Ultra")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
CLK_OUT_A, an external clock output function driven from the clock
control unit, on the R40 is sometimes used to provide a low rate low
power clock to a WiFi or Bluetooth controller.
This patch adds a pinmux setting for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
