The openvswitch module fails initialization when used in a kernel
without IPv6 enabled. nf_conncount_init() fails because the ct code
unconditionally tries to initialize the netns IPv6 related bit,
regardless of the build option. The change below ignores the IPv6
part if not enabled.
Note that the corresponding _put() function already has this IPv6
configuration check.
Fixes: 11efd5cb04 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
conntrack mark based dump filtering may falsely skip entries if a mask
is given: If the mask-based check does not filter out the entry, the
else-if check is always true and compares the mark without considering
the mask. The if/else-if logic seems wrong.
Given that the mask during filter setup is implicitly set to 0xffffffff
if not specified explicitly, the mark filtering flags seem to just
complicate things. Restore the previously used approach by always
matching against a zero mask is no filter mark is given.
Fixes: cb8aa9a3af ("netfilter: ctnetlink: add kernel side filtering for dump")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On x86_64, each notification results in one skbuff allocation which
consumes at least 768 bytes due to the skbuff overhead.
This patch coalesces several notifications into one single skbuff, so
each notification consumes at least ~211 bytes, that ~3.5 times less
memory consumption. As a result, this is reducing the chances to exhaust
the netlink socket receive buffer.
Rule of thumb is that each notification batch only contains netlink
messages whose report flag is the same, nfnetlink_send() requires this
to do appropriate delivery to userspace, either via unicast (echo
mode) or multicast (monitor mode).
The skbuff control buffer is used to annotate the report flag for later
handling at the new coalescing routine.
The batch skbuff notification size is NLMSG_GOODSIZE, using a larger
skbuff would allow for more socket receiver buffer savings (to amortize
the cost of the skbuff even more), however, going over that size might
break userspace applications, so let's be conservative and stick to
NLMSG_GOODSIZE.
Reported-by: Phil Sutter <phil@nwl.cc>
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The indexes to the nf_nat_l[34]protos arrays come from userspace. So
check the tuple's family, e.g. l3num, when creating the conntrack in
order to prevent an OOB memory access during setup. Here is an example
kernel panic on 4.14.180 when userspace passes in an index greater than
NFPROTO_NUMPROTO.
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:...
Process poc (pid: 5614, stack limit = 0x00000000a3933121)
CPU: 4 PID: 5614 Comm: poc Tainted: G S W O 4.14.180-g051355490483
Hardware name: Qualcomm Technologies, Inc. SM8150 V2 PM8150 Google Inc. MSM
task: 000000002a3dfffe task.stack: 00000000a3933121
pc : __cfi_check_fail+0x1c/0x24
lr : __cfi_check_fail+0x1c/0x24
...
Call trace:
__cfi_check_fail+0x1c/0x24
name_to_dev_t+0x0/0x468
nfnetlink_parse_nat_setup+0x234/0x258
ctnetlink_parse_nat_setup+0x4c/0x228
ctnetlink_new_conntrack+0x590/0xc40
nfnetlink_rcv_msg+0x31c/0x4d4
netlink_rcv_skb+0x100/0x184
nfnetlink_rcv+0xf4/0x180
netlink_unicast+0x360/0x770
netlink_sendmsg+0x5a0/0x6a4
___sys_sendmsg+0x314/0x46c
SyS_sendmsg+0xb4/0x108
el0_svc_naked+0x34/0x38
This crash is not happening since 5.4+, however, ctnetlink still
allows for creating entries with unsupported layer 3 protocol number.
Fixes: c1d10adb4a ("[NETFILTER]: Add ctnetlink port for nf_conntrack")
Signed-off-by: Will McVicker <willmcvicker@google.com>
[pablo@netfilter.org: rebased original patch on top of nf.git]
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When we clone state only add_time was cloned. It missed values like
bytes, packets. Now clone the all members of the structure.
v1->v3:
- use memcpy to copy the entire structure
Fixes: 80c9abaabf ("[XFRM]: Extension for dynamic update of endpoint address(es)")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
XFRMA_SEC_CTX was not cloned from the old to the new.
Migrate this attribute during XFRMA_MSG_MIGRATE
v1->v2:
- return -ENOMEM on error
v2->v3:
- fix return type to int
Fixes: 80c9abaabf ("[XFRM]: Extension for dynamic update of endpoint address(es)")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
XFRMA_SET_MARK and XFRMA_SET_MARK_MASK was not cloned from the old
to the new. Migrate these two attributes during XFRMA_MSG_MIGRATE
Fixes: 9b42c1f179 ("xfrm: Extend the output_mark to support input direction and masking.")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Since p points at raw xdr data, there's no guarantee that it's NULL
terminated, so we should give a length. And probably escape any special
characters too.
Reported-by: Zhi Li <yieli@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
The unicast packet rerouting code makes several assumptions. For
instance it assumes that there is always exactly one destination in the
TT. This breaks for multicast frames in a unicast packets in several ways:
For one thing if there is actually no TT entry and the destination node
was selected due to the multicast tvlv flags it announced. Then an
intermediate node will wrongly drop the packet.
For another thing if there is a TT entry but the TTVN of this entry is
newer than the originally addressed destination node: Then the
intermediate node will wrongly redirect the packet, leading to
duplicated multicast packets at a multicast listener and missing
packets at other multicast listeners or multicast routers.
Fixing this by not applying the unicast packet rerouting to batman-adv
unicast packets with a multicast payload. We are not able to detect a
roaming multicast listener at the moment and will just continue to send
the multicast frame to both the new and old destination for a while in
case of such a roaming multicast listener.
Fixes: a73105b8d4 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The following deadlock scenario is triggered by syzbot:
Thread A: Thread B:
tcf_idr_check_alloc()
...
populate_metalist()
rtnl_unlock()
rtnl_lock()
...
request_module() tcf_idr_check_alloc()
rtnl_lock()
At this point, thread A is waiting for thread B to release RTNL
lock, while thread B is waiting for thread A to commit the IDR
change with tcf_idr_insert() later.
Break this deadlock situation by preloading ife modules earlier,
before tcf_idr_check_alloc(), this is fine because we only need
to load modules we need potentially.
Reported-and-tested-by: syzbot+80e32b5d1f9923f8ace6@syzkaller.appspotmail.com
Fixes: 0190c1d452 ("net: sched: atomically check-allocate action")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using tp_reserve to calculate netoff can overflow as
tp_reserve is unsigned int and netoff is unsigned short.
This may lead to macoff receving a smaller value then
sizeof(struct virtio_net_hdr), and if po->has_vnet_hdr
is set, an out-of-bounds write will occur when
calling virtio_net_hdr_from_skb.
The bug is fixed by converting netoff to unsigned int
and checking if it exceeds USHRT_MAX.
This addresses CVE-2020-14386
Fixes: 8913336a7e ("packet: add PACKET_RESERVE sockopt")
Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
When an ISM device is removed, all its linkgroups are terminated,
i.e. all the corresponding connections are killed.
Connection killing invokes smc_close_active_abort(), which decreases
the sock refcount for certain states to simulate passive closing.
And it cancels the close worker and has to give up the sock lock for
this timeframe. This opens the door for a passive close worker or a
socket close to run in between. In this case smc_close_active_abort() and
passive close worker resp. smc_release() might do a sock_put for passive
closing. This causes:
[ 1323.315943] refcount_t: underflow; use-after-free.
[ 1323.316055] WARNING: CPU: 3 PID: 54469 at lib/refcount.c:28 refcount_warn_saturate+0xe8/0x130
[ 1323.316069] Kernel panic - not syncing: panic_on_warn set ...
[ 1323.316084] CPU: 3 PID: 54469 Comm: uperf Not tainted 5.9.0-20200826.rc2.git0.46328853ed20.300.fc32.s390x+debug #1
[ 1323.316096] Hardware name: IBM 2964 NC9 702 (z/VM 6.4.0)
[ 1323.316108] Call Trace:
[ 1323.316125] [<00000000c0d4aae8>] show_stack+0x90/0xf8
[ 1323.316143] [<00000000c15989b0>] dump_stack+0xa8/0xe8
[ 1323.316158] [<00000000c0d8344e>] panic+0x11e/0x288
[ 1323.316173] [<00000000c0d83144>] __warn+0xac/0x158
[ 1323.316187] [<00000000c1597a7a>] report_bug+0xb2/0x130
[ 1323.316201] [<00000000c0d36424>] monitor_event_exception+0x44/0xc0
[ 1323.316219] [<00000000c195c716>] pgm_check_handler+0x1da/0x238
[ 1323.316234] [<00000000c151844c>] refcount_warn_saturate+0xec/0x130
[ 1323.316280] ([<00000000c1518448>] refcount_warn_saturate+0xe8/0x130)
[ 1323.316310] [<000003ff801f2e2a>] smc_release+0x192/0x1c8 [smc]
[ 1323.316323] [<00000000c169f1fa>] __sock_release+0x5a/0xe0
[ 1323.316334] [<00000000c169f2ac>] sock_close+0x2c/0x40
[ 1323.316350] [<00000000c1086de0>] __fput+0xb8/0x278
[ 1323.316362] [<00000000c0db1e0e>] task_work_run+0x76/0xb8
[ 1323.316393] [<00000000c0d8ab84>] do_exit+0x26c/0x520
[ 1323.316408] [<00000000c0d8af08>] do_group_exit+0x48/0xc0
[ 1323.316421] [<00000000c0d8afa8>] __s390x_sys_exit_group+0x28/0x38
[ 1323.316433] [<00000000c195c32c>] system_call+0xe0/0x2b4
[ 1323.316446] 1 lock held by uperf/54469:
[ 1323.316456] #0: 0000000044125e60 (&sb->s_type->i_mutex_key#9){+.+.}-{3:3}, at: __sock_release+0x44/0xe0
The patch rechecks sock state in smc_close_active_abort() after
smc_close_cancel_work() to avoid duplicate decrease of sock
refcount for the same purpose.
Fixes: 611b63a127 ("net/smc: cancel tx worker in case of socket aborts")
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC tries to make use of SMCD first. If a problem shows up,
it tries to switch to SMCR. If the SMCD initializing problem shows
up after the SMCD connection has already been initialized, field
rx_off keeps the wrong SMCD value for SMCR, which results in corrupted
data at the receiver.
This patch adds an explicit (re-)setting of field rx_off to zero if the
connection uses SMCR.
Fixes: be244f28d2 ("net/smc: add SMC-D support in data transfer")
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older SMCR implementations had no link failover support and used one
link only. Because the handshake protocol requires to try the
establishment of a second link the old code sent a fake add_link message
and declined any server response afterwards.
The current code supports multiple links and inspects the received fake
add_link message more closely. To tolerate the fake add_link messages
smc_llc_is_local_add_link() needs an improved check of the message to
be able to separate between locally enqueued and fake add_link messages.
And smc_llc_cli_add_link() needs to check if the provided qp_mtu size is
invalid and reject the add_link request in that case.
Fixes: c48254fa48 ("net/smc: move add link processing for new device into llc layer")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot is reporting hung task at nbd_ioctl() [1], for there are two
problems regarding TIPC's connectionless socket's shutdown() operation.
----------
#include <fcntl.h>
#include <sys/socket.h>
#include <sys/ioctl.h>
#include <linux/nbd.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
const int fd = open("/dev/nbd0", 3);
alarm(5);
ioctl(fd, NBD_SET_SOCK, socket(PF_TIPC, SOCK_DGRAM, 0));
ioctl(fd, NBD_DO_IT, 0); /* To be interrupted by SIGALRM. */
return 0;
}
----------
One problem is that wait_for_completion() from flush_workqueue() from
nbd_start_device_ioctl() from nbd_ioctl() cannot be completed when
nbd_start_device_ioctl() received a signal at wait_event_interruptible(),
for tipc_shutdown() from kernel_sock_shutdown(SHUT_RDWR) from
nbd_mark_nsock_dead() from sock_shutdown() from nbd_start_device_ioctl()
is failing to wake up a WQ thread sleeping at wait_woken() from
tipc_wait_for_rcvmsg() from sock_recvmsg() from sock_xmit() from
nbd_read_stat() from recv_work() scheduled by nbd_start_device() from
nbd_start_device_ioctl(). Fix this problem by always invoking
sk->sk_state_change() (like inet_shutdown() does) when tipc_shutdown() is
called.
The other problem is that tipc_wait_for_rcvmsg() cannot return when
tipc_shutdown() is called, for tipc_shutdown() sets sk->sk_shutdown to
SEND_SHUTDOWN (despite "how" is SHUT_RDWR) while tipc_wait_for_rcvmsg()
needs sk->sk_shutdown set to RCV_SHUTDOWN or SHUTDOWN_MASK. Fix this
problem by setting sk->sk_shutdown to SHUTDOWN_MASK (like inet_shutdown()
does) when the socket is connectionless.
[1] https://syzkaller.appspot.com/bug?id=3fe51d307c1f0a845485cf1798aa059d12bf18b2
Reported-by: syzbot <syzbot+e36f41d207137b5d12f7@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit added the possible value of '2', but it cannot be set. Fix
it by adjusting the maximum value to '2'. This is consistent with the
corresponding IPv4 sysctl.
Before:
# sysctl -w net.ipv6.fib_multipath_hash_policy=2
sysctl: setting key "net.ipv6.fib_multipath_hash_policy": Invalid argument
net.ipv6.fib_multipath_hash_policy = 2
# sysctl net.ipv6.fib_multipath_hash_policy
net.ipv6.fib_multipath_hash_policy = 0
After:
# sysctl -w net.ipv6.fib_multipath_hash_policy=2
net.ipv6.fib_multipath_hash_policy = 2
# sysctl net.ipv6.fib_multipath_hash_policy
net.ipv6.fib_multipath_hash_policy = 2
Fixes: d8f74f0975 ("ipv6: Support multipath hashing on inner IP pkts")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error on calling kthread_create_on_node prints wrong function name,
kernel_thread.
Fixes: 94dcf29a11 ("kthread: use kthread_create_on_node()")
Signed-off-by: Leesoo Ahn <dev@ooseel.net>
Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Do not delete clash entries on reply, let them expire instead,
from Florian Westphal.
2) Do not report EAGAIN to nfnetlink, otherwise this enters a busy loop.
Update nfnetlink_unicast() to translate EAGAIN to ENOBUFS.
3) Remove repeated words in code comments, from Randy Dunlap.
4) Several patches for the flowtable selftests, from Fabian Frederick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'this_cpu_ptr()' is used to obtain the AEAD key' TFM on the current
CPU for encryption, however the execution can be preemptible since it's
actually user-space context, so the 'using smp_processor_id() in
preemptible' has been observed.
We fix the issue by using the 'get/put_cpu_ptr()' API which consists of
a 'preempt_disable()' instead.
Fixes: fc1b6d6de2 ("tipc: introduce TIPC encryption & authentication")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its possible that we have more than one packet with the same ct tuple
simultaneously, e.g. when an application emits n packets on same UDP
socket from multiple threads.
NAT rules might be applied to those packets. With the right set of rules,
n packets will be mapped to m destinations, where at least two packets end
up with the same destination.
When this happens, the existing clash resolution may merge the skb that
is processed after the first has been received with the identical tuple
already in hash table.
However, its possible that this identical tuple is a NAT_CLASH tuple.
In that case the second skb will be sent, but no reply can be received
since the reply that is processed first removes the NAT_CLASH tuple.
Do not auto-delete, this gives a 1 second window for replies to be passed
back to originator.
Packets that are coming later (udp stream case) will not be affected:
they match the original ct entry, not a NAT_CLASH one.
Also prevent NAT_CLASH entries from getting offloaded.
Fixes: 6a757c07e5 ("netfilter: conntrack: allow insertion of clashing entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Frontend callback reports EAGAIN to nfnetlink to retry a command, this
is used to signal that module autoloading is required. Unfortunately,
nlmsg_unicast() reports EAGAIN in case the receiver socket buffer gets
full, so it enters a busy-loop.
This patch updates nfnetlink_unicast() to turn EAGAIN into ENOBUFS and
to use nlmsg_unicast(). Remove the flags field in nfnetlink_unicast()
since this is always MSG_DONTWAIT in the existing code which is exactly
what nlmsg_unicast() passes to netlink_unicast() as parameter.
Fixes: 96518518cc ("netfilter: add nftables")
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Drop duplicated words in net/netfilter/ and net/ipv4/netfilter/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When ->init() fails, ->destroy() is called to clean up.
So it is unnecessary to clean up in red_init(), and it
would cause some refcount underflow.
Fixes: aee9caa03f ("net: sched: sch_red: Add qevents "early_drop" and "mark"")
Reported-and-tested-by: syzbot+b33c1cb0a30ebdc8a5f9@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+e5ea5f8a3ecfd4427a1c@syzkaller.appspotmail.com
Cc: Petr Machata <petrm@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data races were reported by KCSAN:
BUG: KCSAN: data-race in netlink_recvmsg / skb_queue_tail
write (marked) to 0xffff8c0986e5a8c8 of 8 bytes by interrupt on cpu 3:
skb_queue_tail+0xcc/0x120
__netlink_sendskb+0x55/0x80
netlink_broadcast_filtered+0x465/0x7e0
nlmsg_notify+0x8f/0x120
rtnl_notify+0x8e/0xb0
__neigh_notify+0xf2/0x120
neigh_update+0x927/0xde0
arp_process+0x8a3/0xf50
arp_rcv+0x27c/0x3b0
__netif_receive_skb_core+0x181c/0x1840
__netif_receive_skb+0x38/0xf0
netif_receive_skb_internal+0x77/0x1c0
napi_gro_receive+0x1bd/0x1f0
e1000_clean_rx_irq+0x538/0xb20 [e1000]
e1000_clean+0x5e4/0x1340 [e1000]
net_rx_action+0x310/0x9d0
__do_softirq+0xe8/0x308
irq_exit+0x109/0x110
do_IRQ+0x7f/0xe0
ret_from_intr+0x0/0x1d
0xffffffffffffffff
read to 0xffff8c0986e5a8c8 of 8 bytes by task 1463 on cpu 0:
netlink_recvmsg+0x40b/0x820
sock_recvmsg+0xc9/0xd0
___sys_recvmsg+0x1a4/0x3b0
__sys_recvmsg+0x86/0x120
__x64_sys_recvmsg+0x52/0x70
do_syscall_64+0xb5/0x360
entry_SYSCALL_64_after_hwframe+0x65/0xca
0xffffffffffffffff
Since the write is under sk_receive_queue->lock but the read
is done as lockless. so fix it by using skb_queue_empty_lockless()
instead of skb_queue_empty() for the read in netlink_rcv_wake()
Signed-off-by: zhudi <zhudi21@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fixes for AQL (airtime queue limits)
* reduce packet loss detection false positives
* a small channel number fix for the 6 GHz band
* a fix for 80+80/160 MHz negotiation
* an nl80211 attribute (NL80211_ATTR_HE_6GHZ_CAPABILITY) fix
* add a missing sanity check for the regulatory code
-----BEGIN PGP SIGNATURE-----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=zMP7
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2020-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have:
* fixes for AQL (airtime queue limits)
* reduce packet loss detection false positives
* a small channel number fix for the 6 GHz band
* a fix for 80+80/160 MHz negotiation
* an nl80211 attribute (NL80211_ATTR_HE_6GHZ_CAPABILITY) fix
* add a missing sanity check for the regulatory code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak in rxkad_verify_response() whereby the response buffer
doesn't get freed if we fail to allocate a ticket buffer.
Fixes: ef68622da9 ("rxrpc: Handle temporary errors better in rxkad security")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=FWHJ
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20200820' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc, afs: Fix probing issues
Here are some fixes for rxrpc and afs to fix issues in the RTT measuring in
rxrpc and thence the Volume Location server probing in afs:
(1) Move the serial number of a received ACK into a local variable to
simplify the next patch.
(2) Fix the loss of RTT samples due to extra interposed ACKs causing
baseline information to be discarded too early. This is a particular
problem for afs when it sends a single very short call to probe a
server it hasn't talked to recently.
(3) Fix rxrpc_kernel_get_srtt() to indicate whether it actually has seen
any valid samples or not.
(4) Remove a field that's set/woken, but never read/waited on.
(5) Expose the RTT and other probe information through procfs to make
debugging of this stuff easier.
(6) Fix VL rotation in afs to only use summary information from VL probing
and not the probe running state (which gets clobbered when next a
probe is issued).
(7) Fix VL rotation to actually return the error aggregated from the probe
errors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that due to a copy & paste error the void pointer
in batadv_choose_backbone_gw() is cast to the wrong type.
Fixing this by using "struct batadv_bla_backbone_gw" instead of "struct
batadv_bla_claim" which better matches the caller's side.
For now it seems that we were lucky because the two structs both have
their orig/vid and addr/vid in the beginning. However I stumbled over
this issue when I was trying to add some debug variables in front of
"orig" in batadv_backbone_gw, which caused hash lookups to fail.
Fixes: 07568d0369 ("batman-adv: don't rely on positions in struct for hashing")
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Fix some comments, including wrong function name, duplicated word and so
on.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the 6 GHz frequency to channel conversion function,
the other way around was previously handled.
Signed-off-by: Amar Singhal <asinghal@codeaurora.org>
Link: https://lore.kernel.org/r/1592599921-10607-1-git-send-email-asinghal@codeaurora.org
[rewrite commit message, hard-code channel 2]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When running a large number of packets per second with a high data rate
and long A-MPDUs, the packet loss threshold can be reached very quickly
when the link conditions change. This frequently shows up as spurious
disconnects.
Mitigate false positives by using a similar logic for regular stations
as the one being used for TDLS, though with a more aggressive timeout.
Packet loss events are only reported if no ACK was received for a second.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200808172542.41628-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix cfg80211_chandef_usable():
consider IEEE80211_VHT_CAP_EXT_NSS_BW when verifying 160/80+80 MHz.
Based on:
"Table 9-272 — Setting of the Supported Channel Width Set subfield and Extended NSS BW
Support subfield at a STA transmitting the VHT Capabilities Information field"
From "Draft P802.11REVmd_D3.0.pdf"
Signed-off-by: Aviad Brikman <aviad.brikman@celeno.com>
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Link: https://lore.kernel.org/r/20200826143139.25976-1-shay.bar@celeno.com
[reformat the code a bit and use u32_get_bits()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Links with low data rates use much smaller aggregates and are much more
sensitive to latency added by bufferbloat.
Tune the assumed aggregation length based on the tx rate duration.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200821163045.62140-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will be used to enhance AQL estimated aggregation length
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200821163045.62140-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since ieee80211_tx_info does not have enough room to encode HE rates, HE
drivers use status->rate to provide rate info.
Store it in struct sta_info and use it for AQL.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200821163045.62140-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
xfrm interfaces currently test for !skb->ignore_df when deciding
whether to update the pmtu on the skb's dst. Because of this, no pmtu
exception is created when we do something like:
ping -s 1438 <dest>
By dropping this check, the pmtu exception will be created and the
next ping attempt will work.
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
napi_disable() makes sure to set the NAPI_STATE_NPSVC bit to prevent
netpoll from accessing rings before init is complete. However, the
same is not done for fresh napi instances in netif_napi_add(),
even though we expect NAPI instances to be added as disabled.
This causes crashes during driver reconfiguration (enabling XDP,
changing the channel count) - if there is any printk() after
netif_napi_add() but before napi_enable().
To ensure memory ordering is correct we need to use RCU accessors.
Reported-by: Rob Sherwood <rsher@fb.com>
Fixes: 2d8bff1269 ("netpoll: Close race condition between poll_one_napi and napi_disable")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After subflow lock is dropped, more wmem might have been made available.
This fixes a deadlock in mptcp_connect.sh 'mmap' mode: wmem is exhausted.
But as the mptcp socket holds on to already-acked data (for retransmit)
no wakeup will occur.
Using 'goto restart' calls mptcp_clean_una(sk) which will free pages
that have been acked completely in the mean time.
Fixes: fb529e62d3 ("mptcp: break and restart in case mptcp sndbuf is full")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9c66d15646 ("taprio: Add support for hardware
offloading") there's a bit of inconsistency when offloading schedules
to the hardware:
In software mode, the gate masks are specified in terms of traffic
classes, so if say "sched-entry S 03 20000", it means that the traffic
classes 0 and 1 are open for 20us; when taprio is offloaded to
hardware, the gate masks are specified in terms of hardware queues.
The idea here is to fix hardware offloading, so schedules in hardware
and software mode have the same behavior. What's needed to do is to
map traffic classes to queues when applying the offload to the driver.
Fixes: 9c66d15646 ("taprio: Add support for hardware offloading")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Aloni reports that when a server disconnects abruptly, a few
memory regions are left DMA mapped. Over time this leak could pin
enough I/O resources to slow or even deadlock an NFS/RDMA client.
I found that if a transport disconnects before pending Send and
FastReg WRs can be posted, the to-be-registered MRs are stranded on
the req's rl_registered list and never released -- since they
weren't posted, there's no Send completion to DMA unmap them.
Reported-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
- Eliminate an oops introduced in v5.8
- Remove a duplicate #include added by nfsd-5.9
-----BEGIN PGP SIGNATURE-----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=czB3
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.9-1' of git://git.linux-nfs.org/projects/cel/cel-2.6
Pull nfs server fixes from Chuck Lever:
- Eliminate an oops introduced in v5.8
- Remove a duplicate #include added by nfsd-5.9
* tag 'nfsd-5.9-1' of git://git.linux-nfs.org/projects/cel/cel-2.6:
SUNRPC: remove duplicate include
nfsd: fix oops on mixed NFSv4/NFSv3 client access
cfpkt_peek_head return 0 and 1, caller is checking error using <0
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Avoid uninitialized memory access when handling DHCP, by Sven Eckelmann
- Fix check for own OGM in OGM receive handler, by Linus Luessing
- Fix netif_rx access for non-interrupt context in BLA, by Jussi Kivilinna
-----BEGIN PGP SIGNATURE-----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=ikYK
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20200824' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- Avoid uninitialized memory access when handling DHCP, by Sven Eckelmann
- Fix check for own OGM in OGM receive handler, by Linus Luessing
- Fix netif_rx access for non-interrupt context in BLA, by Jussi Kivilinna
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function consume_skb is only meaningful when tracing is enabled.
This patch makes it conditional on CONFIG_TRACEPOINTS.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two main problems seen when removing NetLabel
mappings: memory leaks and potentially extra audit noise.
The memory leaks are caused by not properly free'ing the mapping's
address selector struct when free'ing the entire entry as well as
not properly cleaning up a temporary mapping entry when adding new
address selectors to an existing entry. This patch fixes both these
problems such that kmemleak reports no NetLabel associated leaks
after running the SELinux test suite.
The potentially extra audit noise was caused by the auditing code in
netlbl_domhsh_remove_entry() being called regardless of the entry's
validity. If another thread had already marked the entry as invalid,
but not removed/free'd it from the list of mappings, then it was
possible that an additional mapping removal audit record would be
generated. This patch fixes this by returning early from the removal
function when the entry was previously marked invalid. This change
also had the side benefit of improving the code by decreasing the
indentation level of large chunk of code by one (accounting for most
of the diffstat).
Fixes: 63c4168874 ("netlabel: Add network address selectors to the NetLabel/LSM domain mapping")
Reported-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With disabling bh in the whole sctp_get_port_local(), when
snum == 0 and too many ports have been used, the do-while
loop will take the cpu for a long time and cause cpu stuck:
[ ] watchdog: BUG: soft lockup - CPU#11 stuck for 22s!
[ ] RIP: 0010:native_queued_spin_lock_slowpath+0x4de/0x940
[ ] Call Trace:
[ ] _raw_spin_lock+0xc1/0xd0
[ ] sctp_get_port_local+0x527/0x650 [sctp]
[ ] sctp_do_bind+0x208/0x5e0 [sctp]
[ ] sctp_autobind+0x165/0x1e0 [sctp]
[ ] sctp_connect_new_asoc+0x355/0x480 [sctp]
[ ] __sctp_connect+0x360/0xb10 [sctp]
There's no need to disable bh in the whole function of
sctp_get_port_local. So fix this cpu stuck by removing
local_bh_disable() called at the beginning, and using
spin_lock_bh() instead.
The same thing was actually done for inet_csk_get_port() in
Commit ea8add2b19 ("tcp/dccp: better use of ephemeral
ports in bind()").
Thanks to Marcelo for pointing the buggy code out.
v1->v2:
- use cond_resched() to yield cpu to other tasks if needed,
as Eric noticed.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Don't flag SCTP heartbeat as invalid for re-used connections,
from Florian Westphal.
2) Bogus overlap report due to rbtree tree rotations, from Stefano Brivio.
3) Detect partial overlap with start end point match, also from Stefano.
4) Skip netlink dump of NFTA_SET_USERDATA is unset.
5) Incorrect nft_list_attributes enumeration definition.
6) Missing zeroing before memcpy to destination register, also
from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2020-08-21
The following pull-request contains BPF updates for your *net* tree.
We've added 11 non-merge commits during the last 5 day(s) which contain
a total of 12 files changed, 78 insertions(+), 24 deletions(-).
The main changes are:
1) three fixes in BPF task iterator logic, from Yonghong.
2) fix for compressed dwarf sections in vmlinux, from Jiri.
3) fix xdp attach regression, from Andrii.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Following bug was reported via irc:
nft list ruleset
set knock_candidates_ipv4 {
type ipv4_addr . inet_service
size 65535
elements = { 127.0.0.1 . 123,
127.0.0.1 . 123 }
}
..
udp dport 123 add @knock_candidates_ipv4 { ip saddr . 123 }
udp dport 123 add @knock_candidates_ipv4 { ip saddr . udp dport }
It should not have been possible to add a duplicate set entry.
After some debugging it turned out that the problem is the immediate
value (123) in the second-to-last rule.
Concatenations use 32bit registers, i.e. the elements are 8 bytes each,
not 6 and it turns out the kernel inserted
inet firewall @knock_candidates_ipv4
element 0100007f ffff7b00 : 0 [end]
element 0100007f 00007b00 : 0 [end]
Note the non-zero upper bits of the first element. It turns out that
nft_immediate doesn't zero the destination register, but this is needed
when the length isn't a multiple of 4.
Furthermore, the zeroing in nft_payload is broken. We can't use
[len / 4] = 0 -- if len is a multiple of 4, index is off by one.
Skip zeroing in this case and use a conditional instead of (len -1) / 4.
Fixes: 49499c3e6e ("netfilter: nf_tables: switch registers to 32 bit addressing")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Kernel sends an empty NFTA_SET_USERDATA attribute with no value if
userspace adds a set with no NFTA_SET_USERDATA attribute.
Fixes: e6d8ecac9e ("netfilter: nf_tables: Add new attributes into nft_set to store user data.")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Getting creative with nft and omitting the interval_overlap()
check from the set_overlap() function, without omitting
set_overlap() altogether, led to the observation of a partial
overlap that wasn't detected, and would actually result in
replacement of the end element of an existing interval.
This is due to the fact that we'll return -EEXIST on a matching,
pre-existing start element, instead of -ENOTEMPTY, and the error
is cleared by API if NLM_F_EXCL is not given. At this point, we
can insert a matching start, and duplicate the end element as long
as we don't end up into other intervals.
For instance, inserting interval 0 - 2 with an existing 0 - 3
interval would result in a single 0 - 2 interval, and a dangling
'3' end element. This is because nft will proceed after inserting
the '0' start element as no error is reported, and no further
conflicting intervals are detected on insertion of the end element.
This needs a different approach as it's a local condition that can
be detected by looking for duplicate ends coming from left and
right, separately. Track those and directly report -ENOTEMPTY on
duplicated end elements for a matching start.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Checks for partial overlaps on insertion assume that end elements
are always descendant nodes of their corresponding start, because
they are inserted later. However, this is not the case if a
previous delete operation caused a tree rotation as part of
rebalancing.
Taking the issue reported by Andreas Fischer as an example, if we
omit delete operations, the existing procedure works because,
equivalently, we are inserting a start item with value 40 in the
this region of the red-black tree with single-sized intervals:
overlap flag
10 (start)
/ \ false
20 (start)
/ \ false
30 (start)
/ \ false
60 (start)
/ \ false
50 (end)
/ \ false
20 (end)
/ \ false
40 (start)
if we now delete interval 30 - 30, the tree can be rearranged in
a way similar to this (note the rotation involving 50 - 50):
overlap flag
10 (start)
/ \ false
20 (start)
/ \ false
25 (start)
/ \ false
70 (start)
/ \ false
50 (end)
/ \ true (from rule a1.)
50 (start)
/ \ true
40 (start)
and we traverse interval 50 - 50 from the opposite direction
compared to what was expected.
To deal with those cases, add a start-before-start rule, b4.,
that covers traversal of existing intervals from the right.
We now need to restrict start-after-end rule b3. to cases
where there are no occurring nodes between existing start and
end elements, because addition of rule b4. isn't sufficient to
ensure that the pre-existing end element we encounter while
descending the tree corresponds to a start element of an
interval that we already traversed entirely.
Different types of overlap detection on trees with rotations
resulting from re-balancing will be covered by nft test case
sets/0044interval_overlap_1.
Reported-by: Andreas Fischer <netfilter@d9c.eu>
Bugzilla: https://bugzilla.netfilter.org/show_bug.cgi?id=1449
Cc: <stable@vger.kernel.org> # 5.6.x
Fixes: 7c84d41416 ("netfilter: nft_set_rbtree: Detect partial overlaps on insertion")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
b->media->send_msg() requires rcu_read_lock(), as we can see
elsewhere in tipc, tipc_bearer_xmit, tipc_bearer_xmit_skb
and tipc_bearer_bc_xmit().
Syzbot has reported this issue as:
net/tipc/bearer.c:466 suspicious rcu_dereference_check() usage!
Workqueue: cryptd cryptd_queue_worker
Call Trace:
tipc_l2_send_msg+0x354/0x420 net/tipc/bearer.c:466
tipc_aead_encrypt_done+0x204/0x3a0 net/tipc/crypto.c:761
cryptd_aead_crypt+0xe8/0x1d0 crypto/cryptd.c:739
cryptd_queue_worker+0x118/0x1b0 crypto/cryptd.c:181
process_one_work+0x94c/0x1670 kernel/workqueue.c:2269
worker_thread+0x64c/0x1120 kernel/workqueue.c:2415
kthread+0x3b5/0x4a0 kernel/kthread.c:291
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293
So fix it by calling rcu_read_lock() in tipc_aead_encrypt_done()
for b->media->send_msg().
Fixes: fc1b6d6de2 ("tipc: introduce TIPC encryption & authentication")
Reported-by: syzbot+47bbc6b678d317cccbe0@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_ct_handle_fragments() shouldn't free the skb when ip_defrag() call
fails. Otherwise, we will cause a double-free bug.
In such cases, just return the error to the caller.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of output and input streams was never being reduced, eg when
processing received INIT or INIT_ACK chunks.
The effect is that DATA chunks can be sent with invalid stream ids
and then discarded by the remote system.
Fixes: 2075e50caf ("sctp: convert to genradix")
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an IPv4 packet inside an IPv6 GRE packet, and the
IP6_TNL_F_RCV_DSCP_COPY flag is set on the tunnel, the IPv4 header would
get corrupted. This is due to the common ip6_tnl_rcv() function assuming
that the inner header is always IPv6. This patch checks the tunnel
protocol for IPv4 inner packets, but still defaults to IPv6.
Fixes: 308edfdf15 ("gre6: Cleanup GREv6 receive path, call common GRE functions")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
7f0a838254 ("bpf, xdp: Maintain info on attached XDP BPF programs in net_device")
inadvertently changed which XDP mode is assumed when no mode flags are
specified explicitly. Previously, driver mode was preferred, if driver
supported it. If not, generic SKB mode was chosen. That commit changed default
to SKB mode always. This patch fixes the issue and restores the original
logic.
Fixes: 7f0a838254 ("bpf, xdp: Maintain info on attached XDP BPF programs in net_device")
Reported-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/bpf/20200820052841.1559757-1-andriin@fb.com
__smc_diag_dump() is potentially copying uninitialized kernel stack memory
into socket buffers, since the compiler may leave a 4-byte hole near the
beginning of `struct smcd_diag_dmbinfo`. Fix it by initializing `dinfo`
with memset().
Fixes: 4b1b7d3b30 ("net/smc: add SMC-D diag support")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix rxrpc_kernel_get_srtt() to indicate the validity of the returned
smoothed RTT. If we haven't had any valid samples yet, the SRTT isn't
useful.
Fixes: c410bf0193 ("rxrpc: Fix the excessive initial retransmission timeout")
Signed-off-by: David Howells <dhowells@redhat.com>
The Rx protocol has a mechanism to help generate RTT samples that works by
a client transmitting a REQUESTED-type ACK when it receives a DATA packet
that has the REQUEST_ACK flag set.
The peer, however, may interpose other ACKs before transmitting the
REQUESTED-ACK, as can be seen in the following trace excerpt:
rxrpc_tx_data: c=00000044 DATA d0b5ece8:00000001 00000001 q=00000001 fl=07
rxrpc_rx_ack: c=00000044 00000001 PNG r=00000000 f=00000002 p=00000000 n=0
rxrpc_rx_ack: c=00000044 00000002 REQ r=00000001 f=00000002 p=00000001 n=0
...
DATA packet 1 (q=xx) has REQUEST_ACK set (bit 1 of fl=xx). The incoming
ping (labelled PNG) hard-acks the request DATA packet (f=xx exceeds the
sequence number of the DATA packet), causing it to be discarded from the Tx
ring. The ACK that was requested (labelled REQ, r=xx references the serial
of the DATA packet) comes after the ping, but the sk_buff holding the
timestamp has gone and the RTT sample is lost.
This is particularly noticeable on RPC calls used to probe the service
offered by the peer. A lot of peers end up with an unknown RTT because we
only ever sent a single RPC. This confuses the server rotation algorithm.
Fix this by caching the information about the outgoing packet in RTT
calculations in the rxrpc_call struct rather than looking in the Tx ring.
A four-deep buffer is maintained and both REQUEST_ACK-flagged DATA and
PING-ACK transmissions are recorded in there. When the appropriate
response ACK is received, the buffer is checked for a match and, if found,
an RTT sample is recorded.
If a received ACK refers to a packet with a later serial number than an
entry in the cache, that entry is presumed lost and the entry is made
available to record a new transmission.
ACKs types other than REQUESTED-type and PING-type cause any matching
sample to be cancelled as they don't necessarily represent a useful
measurement.
If there's no space in the buffer on ping/data transmission, the sample
base is discarded.
Fixes: 50235c4b5a ("rxrpc: Obtain RTT data by requesting ACKs on DATA packets")
Signed-off-by: David Howells <dhowells@redhat.com>
If an sctp connection gets re-used, heartbeats are flagged as invalid
because their vtag doesn't match.
Handle this in a similar way as TCP conntrack when it suspects that the
endpoints and conntrack are out-of-sync.
When a HEARTBEAT request fails its vtag validation, flag this in the
conntrack state and accept the packet.
When a HEARTBEAT_ACK is received with an invalid vtag in the reverse
direction after we allowed such a HEARTBEAT through, assume we are
out-of-sync and re-set the vtag info.
v2: remove left-over snippet from an older incarnation that moved
new_state/old_state assignments, thats not needed so keep that
as-is.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Evidently, when I did this previously, we didn't have more than
10 policies and didn't run into the reallocation path, because
it's missing a memset() for the unused policies. Fix that.
Fixes: d07dcf9aad ("netlink: add infrastructure to expose policies to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove linux/sunrpc/auth_gss.h which is included more than once
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
The Kconfig help text contains the phrase "the the" in the help
text. Fix this and reformat the block of help text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy ethtool userspace tool shows an error when no features could
be changed. It's useful to have a netlink reply to be able to show this
error when __netdev_update_features wasn't called, for example:
1. ethtool -k eth0
large-receive-offload: off
2. ethtool -K eth0 rx-fcs on
3. ethtool -K eth0 lro on
Could not change any device features
rx-lro: off [requested on]
4. ethtool -K eth0 lro on
# The output should be the same, but without this patch the kernel
# doesn't send the reply, and ethtool is unable to detect the error.
This commit makes ethtool-netlink always return a reply when requested,
and it still avoids unnecessary calls to __netdev_update_features if the
wanted features haven't changed.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool-netlink ignores dev->hw_features and may confuse the drivers by
asking them to enable features not in the hw_features bitmask. For
example:
1. ethtool -k eth0
tls-hw-tx-offload: off [fixed]
2. ethtool -K eth0 tls-hw-tx-offload on
tls-hw-tx-offload: on
3. ethtool -k eth0
tls-hw-tx-offload: on [fixed]
Fitler out dev->hw_features from req_wanted to fix it and to resemble
the legacy ethtool behavior.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ethtool-netlink calculates new wanted bits as:
(req_wanted & req_mask) | (old_active & ~req_mask)
It completely discards the old wanted bits, so they are forgotten with
the next ethtool command. Sample steps to reproduce:
1. ethtool -k eth0
tx-tcp-segmentation: on # TSO is on from the beginning
2. ethtool -K eth0 tx off
tx-tcp-segmentation: off [not requested]
3. ethtool -k eth0
tx-tcp-segmentation: off [requested on]
4. ethtool -K eth0 rx off # Some change unrelated to TSO
5. ethtool -k eth0
tx-tcp-segmentation: off # "Wanted on" is forgotten
This commit fixes it by changing the formula to:
(req_wanted & req_mask) | (old_wanted & ~req_mask),
where old_active was replaced by old_wanted to account for the wanted
bits.
The shortcut condition for the case where nothing was changed now
compares wanted bitmasks, instead of wanted to active.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to do 3 things for ipv6_dev_find():
As David A. noticed,
- rt6_lookup() is not really needed. Different from __ip_dev_find(),
ipv6_dev_find() doesn't have a compatibility problem, so remove it.
As Hideaki suggested,
- "valid" (non-tentative) check for the address is also needed.
ipv6_chk_addr() calls ipv6_chk_addr_and_flags(), which will
traverse the address hash list, but it's heavy to be called
inside ipv6_dev_find(). This patch is to reuse the code of
ipv6_chk_addr_and_flags() for ipv6_dev_find().
- dev parameter is passed into ipv6_dev_find(), as link-local
addresses from user space has sin6_scope_id set and the dev
lookup needs it.
Fixes: 81f6cb3122 ("ipv6: add ipv6_dev_find()")
Suggested-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_carve_frag_list() may return -ENOMEM in pskb_carve_inside_nonlinear().
we should handle this correctly or we would get wrong sk_buff.
Fixes: 6fa01ccd88 ("skbuff: Add pskb_extract() helper function")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
batadv_bla_send_claim() gets called from worker thread context through
batadv_bla_periodic_work(), thus netif_rx_ni needs to be used in that
case. This fixes "NOHZ: local_softirq_pending 08" log messages seen
when batman-adv is enabled.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The own OGM check is currently misplaced and can lead to the following
issues:
For one thing we might receive an aggregated OGM from a neighbor node
which has our own OGM in the first place. We would then not only skip
our own OGM but erroneously also any other, following OGM in the
aggregate.
For another, we might receive an OGM aggregate which has our own OGM in
a place other then the first one. Then we would wrongly not skip this
OGM, leading to populating the orginator and gateway table with ourself.
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The gateway client code can try to optimize the delivery of DHCP packets to
avoid broadcasting them through the whole mesh. But also transmissions to
the client can be optimized by looking up the destination via the chaddr of
the DHCP packet.
But the chaddr is currently only done when chaddr is fully inside the
non-paged area of the skbuff. Otherwise it will not be initialized and the
unoptimized path should have been taken.
But the implementation didn't handle this correctly. It didn't retrieve the
correct chaddr but still tried to perform the TT lookup with this
uninitialized memory.
Reported-by: syzbot+ab16e463b903f5a37036@syzkaller.appspotmail.com
Fixes: 6c413b1c22 ("batman-adv: send every DHCP packet as bat-unicast")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Pull networking fixes from David Miller:
"Another batch of fixes:
1) Remove nft_compat counter flush optimization, it generates warnings
from the refcount infrastructure. From Florian Westphal.
2) Fix BPF to search for build id more robustly, from Jiri Olsa.
3) Handle bogus getopt lengths in ebtables, from Florian Westphal.
4) Infoleak and other fixes to j1939 CAN driver, from Eric Dumazet and
Oleksij Rempel.
5) Reset iter properly on mptcp sendmsg() error, from Florian
Westphal.
6) Show a saner speed in bonding broadcast mode, from Jarod Wilson.
7) Various kerneldoc fixes in bonding and elsewhere, from Lee Jones.
8) Fix double unregister in bonding during namespace tear down, from
Cong Wang.
9) Disable RP filter during icmp_redirect selftest, from David Ahern"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (75 commits)
otx2_common: Use devm_kcalloc() in otx2_config_npa()
net: qrtr: fix usage of idr in port assignment to socket
selftests: disable rp_filter for icmp_redirect.sh
Revert "net: xdp: pull ethernet header off packet after computing skb->protocol"
phylink: <linux/phylink.h>: fix function prototype kernel-doc warning
mptcp: sendmsg: reset iter on error redux
net: devlink: Remove overzealous WARN_ON with snapshots
tipc: not enable tipc when ipv6 works as a module
tipc: fix uninit skb->data in tipc_nl_compat_dumpit()
net: Fix potential wrong skb->protocol in skb_vlan_untag()
net: xdp: pull ethernet header off packet after computing skb->protocol
ipvlan: fix device features
bonding: fix a potential double-unregister
can: j1939: add rxtimer for multipacket broadcast session
can: j1939: abort multipacket broadcast session when timeout occurs
can: j1939: cancel rxtimer on multipacket broadcast session complete
can: j1939: fix support for multipacket broadcast message
net: fddi: skfp: cfm: Remove seemingly unused variable 'ID_sccs'
net: fddi: skfp: cfm: Remove set but unused variable 'oldstate'
net: fddi: skfp: smt: Remove seemingly unused variable 'ID_sccs'
...
Passing large uint32 sockaddr_qrtr.port numbers for port allocation
triggers a warning within idr_alloc() since the port number is cast
to int, and thus interpreted as a negative number. This leads to
the rejection of such valid port numbers in qrtr_port_assign() as
idr_alloc() fails.
To avoid the problem, switch to idr_alloc_u32() instead.
Fixes: bdabad3e36 ("net: Add Qualcomm IPC router")
Reported-by: syzbot+f31428628ef672716ea8@syzkaller.appspotmail.com
Signed-off-by: Necip Fazil Yildiran <necip@google.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xiumei reported a bug with espintcp over IPv6 in transport mode,
because xfrm6_transport_finish expects to find IP6CB data (struct
inet6_skb_cb). Currently, espintcp zeroes the CB, but the relevant
part is actually preserved by previous layers (first set up by tcp,
then strparser only zeroes a small part of tcp_skb_tb), so we can just
relocate it to the start of skb->cb.
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This fix wasn't correct: When this function is invoked from the
retransmission worker, the iterator contains garbage and resetting
it causes a crash.
As the work queue should not be performance critical also zero the
msghdr struct.
Fixes: 3575938313 "(mptcp: sendmsg: reset iter on error)"
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to trigger this WARN_ON from user space by triggering a
devlink snapshot with an ID which already exists. We don't need both
-EEXISTS being reported and spamming the kernel log.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using ipv6_dev_find() in one module, it requires ipv6 not to
work as a module. Otherwise, this error occurs in build:
undefined reference to `ipv6_dev_find'.
So fix it by adding "depends on IPV6 || IPV6=n" to tipc/Kconfig,
as it does in sctp/Kconfig.
Fixes: 5a6f6f5791 ("tipc: set ub->ifindex for local ipv6 address")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__tipc_nl_compat_dumpit() has two callers, and it expects them to
pass a valid nlmsghdr via arg->data. This header is artificial and
crafted just for __tipc_nl_compat_dumpit().
tipc_nl_compat_publ_dump() does so by putting a genlmsghdr as well
as some nested attribute, TIPC_NLA_SOCK. But the other caller
tipc_nl_compat_dumpit() does not, this leaves arg->data uninitialized
on this call path.
Fix this by just adding a similar nlmsghdr without any payload in
tipc_nl_compat_dumpit().
This bug exists since day 1, but the recent commit 6ea67769ff
("net: tipc: prepare attrs in __tipc_nl_compat_dumpit()") makes it
easier to appear.
Reported-and-tested-by: syzbot+0e7181deafa7e0b79923@syzkaller.appspotmail.com
Fixes: d0796d1ef6 ("tipc: convert legacy nl bearer dump to nl compat")
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Endianness issue in IPv4 option support in nft_exthdr,
from Stephen Suryaputra.
2) Removes the waitcount optimization in nft_compat,
from Florian Westphal.
3) Remove ipv6 -> nf_defrag_ipv6 module dependency, from
Florian Westphal.
4) Memleak in chain binding support, also from Florian.
5) Simplify nft_flowtable.sh selftest, from Fabian Frederick.
6) Optional MTU arguments for selftest nft_flowtable.sh,
also from Fabian.
7) Remove noise error report when killing process in
selftest nft_flowtable.sh, from Fabian Frederick.
8) Reject bogus getsockopt option length in ebtables,
from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAl83p3MTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqcsSB/9YMSKfcLUNv8eB/J3kPb4n6wlrBO8d
BLHGddA5+qVbki5Tx3rQ7qA+fj60v2bVWQYiwC4okBIE3h+uIi/vq+S+oYjA7ncA
E6bd0804AgKYbsGWaYMQOrOfVlLyJOk886XOsd2szkpopdPCdgHz45RVgx+wXkk/
4fUgeiGuBSNI7Kgei6w+OrMqB+dXyUZR5D0MePobVnN4vMjEZd4UsD6TAB3y4C3L
Ar9lAj/uPiiUEq/ow7J4kYtfw3DibMFM6JRAJ5+B7dXmBZ4TeAPxlG9XxmAKKHMX
R/QxkyZnkE3AIba6YHpIeYLQZyFa41363W5Z70rsA+fQ5Mig5jWXoNnY
=hWSB
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.9-20200815' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2020-08-15
this is a pull request of 4 patches for net/master.
All patches are by Zhang Changzhong and fix broadcast related problems in the
j1939 CAN networking stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We may access the two bytes after vlan_hdr in vlan_set_encap_proto(). So
we should pull VLAN_HLEN + sizeof(unsigned short) in skb_vlan_untag() or
we may access the wrong data.
Fixes: 0d5501c1c8 ("net: Always untag vlan-tagged traffic on input.")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an XDP program changes the ethernet header protocol field,
eth_type_trans is used to recalculate skb->protocol. In order for
eth_type_trans to work correctly, the ethernet header must actually be
part of the skb data segment, so the code first pushes that onto the
head of the skb. However, it subsequently forgets to pull it back off,
making the behavior of the passed-on packet inconsistent between the
protocol modifying case and the static protocol case. This patch fixes
the issue by simply pulling the ethernet header back off of the skb
head.
Fixes: 2972495699 ("net: fix generic XDP to handle if eth header was mangled")
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- some code cleanup
- a couple of static analysis fixes
- setattr: try to pick a fid associated with the file rather than the
dentry, which might sometimes matter
-----BEGIN PGP SIGNATURE-----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=hwGq
-----END PGP SIGNATURE-----
Merge tag '9p-for-5.9-rc1' of git://github.com/martinetd/linux
Pull 9p updates from Dominique Martinet:
- some code cleanup
- a couple of static analysis fixes
- setattr: try to pick a fid associated with the file rather than the
dentry, which might sometimes matter
* tag '9p-for-5.9-rc1' of git://github.com/martinetd/linux:
9p: Remove unneeded cast from memory allocation
9p: remove unused code in 9p
net/9p: Fix sparse endian warning in trans_fd.c
9p: Fix memory leak in v9fs_mount
9p: retrieve fid from file when file instance exist.
Highlights include:
Stable fixes:
- pNFS: Don't return layout segments that are being used for I/O
- pNFS: Don't move layout segments off the active list when being used for I/O
Features:
- NFS: Add support for user xattrs through the NFSv4.2 protocol
- NFS: Allow applications to speed up readdir+statx() using AT_STATX_DONT_SYNC
- NFSv4.0 allow nconnect for v4.0
Bugfixes and cleanups:
- nfs: ensure correct writeback errors are returned on close()
- nfs: nfs_file_write() should check for writeback errors
- nfs: Fix getxattr kernel panic and memory overflow
- NFS: Fix the pNFS/flexfiles mirrored read failover code
- SUNRPC: dont update timeout value on connection reset
- freezer: Add unsafe versions of freezable_schedule_timeout_interruptible for NFS
- sunrpc: destroy rpc_inode_cachep after unregister_filesystem
-----BEGIN PGP SIGNATURE-----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=k4pE
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.9-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Stable fixes:
- pNFS: Don't return layout segments that are being used for I/O
- pNFS: Don't move layout segments off the active list when being used for I/O
Features:
- NFS: Add support for user xattrs through the NFSv4.2 protocol
- NFS: Allow applications to speed up readdir+statx() using AT_STATX_DONT_SYNC
- NFSv4.0 allow nconnect for v4.0
Bugfixes and cleanups:
- nfs: ensure correct writeback errors are returned on close()
- nfs: nfs_file_write() should check for writeback errors
- nfs: Fix getxattr kernel panic and memory overflow
- NFS: Fix the pNFS/flexfiles mirrored read failover code
- SUNRPC: dont update timeout value on connection reset
- freezer: Add unsafe versions of freezable_schedule_timeout_interruptible for NFS
- sunrpc: destroy rpc_inode_cachep after unregister_filesystem"
* tag 'nfs-for-5.9-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (32 commits)
NFS: Fix flexfiles read failover
fs: nfs: delete repeated words in comments
rpc_pipefs: convert comma to semicolon
nfs: Fix getxattr kernel panic and memory overflow
NFS: Don't return layout segments that are in use
NFS: Don't move layouts to plh_return_segs list while in use
NFS: Add layout segment info to pnfs read/write/commit tracepoints
NFS: Add tracepoints for layouterror and layoutstats.
NFS: Report the stateid + status in trace_nfs4_layoutreturn_on_close()
SUNRPC dont update timeout value on connection reset
nfs: nfs_file_write() should check for writeback errors
nfs: ensure correct writeback errors are returned on close()
NFSv4.2: xattr cache: get rid of cache discard work queue
NFS: remove redundant initialization of variable result
NFSv4.0 allow nconnect for v4.0
freezer: Add unsafe versions of freezable_schedule_timeout_interruptible for NFS
sunrpc: destroy rpc_inode_cachep after unregister_filesystem
NFSv4.2: add client side xattr caching.
NFSv4.2: hook in the user extended attribute handlers
NFSv4.2: add the extended attribute proc functions.
...
According to SAE J1939/21 (Chapter 5.12.3 and APPENDIX C), for transmit side
the required time interval between packets of a multipacket broadcast message
is 50 to 200 ms, the responder shall use a timeout of 250ms (provides margin
allowing for the maximumm spacing of 200ms). For receive side a timeout will
occur when a time of greater than 750 ms elapsed between two message packets
when more packets were expected.
So this patch fix and add rxtimer for multipacket broadcast session.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1596599425-5534-5-git-send-email-zhangchangzhong@huawei.com
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If timeout occurs, j1939_tp_rxtimer() first calls hrtimer_start() to restart
rxtimer, and then calls __j1939_session_cancel() to set session->state =
J1939_SESSION_WAITING_ABORT. At next timeout expiration, because of the
J1939_SESSION_WAITING_ABORT session state j1939_tp_rxtimer() will call
j1939_session_deactivate_activate_next() to deactivate current session, and
rxtimer won't be set.
But for multipacket broadcast session, __j1939_session_cancel() don't set
session->state = J1939_SESSION_WAITING_ABORT, thus current session won't be
deactivate and hrtimer_start() is called to start new rxtimer again and again.
So fix it by moving session->state = J1939_SESSION_WAITING_ABORT out of if
(!j1939_cb_is_broadcast(&session->skcb)) statement.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1596599425-5534-4-git-send-email-zhangchangzhong@huawei.com
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If j1939_xtp_rx_dat_one() receive last frame of multipacket broadcast message,
j1939_session_timers_cancel() should be called to cancel rxtimer.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1596599425-5534-3-git-send-email-zhangchangzhong@huawei.com
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently j1939_tp_im_involved_anydir() in j1939_tp_recv() check the previously
set flags J1939_ECU_LOCAL_DST and J1939_ECU_LOCAL_SRC of incoming skb, thus
multipacket broadcast message was aborted by receive side because it may come
from remote ECUs and have no exact dst address. Similarly, j1939_tp_cmd_recv()
and j1939_xtp_rx_dat() didn't process broadcast message.
So fix it by checking and process broadcast message in j1939_tp_recv(),
j1939_tp_cmd_recv() and j1939_xtp_rx_dat().
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1596599425-5534-2-git-send-email-zhangchangzhong@huawei.com
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Daniel Borkmann says:
====================
pull-request: bpf 2020-08-15
The following pull-request contains BPF updates for your *net* tree.
We've added 23 non-merge commits during the last 4 day(s) which contain
a total of 32 files changed, 421 insertions(+), 141 deletions(-).
The main changes are:
1) Fix sock_ops ctx access splat due to register override, from John Fastabend.
2) Batch of various fixes to libbpf, bpftool, and selftests when testing build
in 32-bit mode, from Andrii Nakryiko.
3) Fix vmlinux.h generation on ARM by mapping GCC built-in types (__Poly*_t)
to equivalent ones clang can work with, from Jean-Philippe Brucker.
4) Fix build_id lookup in bpf_get_stackid() helper by walking all NOTE ELF
sections instead of just first, from Jiri Olsa.
5) Avoid use of __builtin_offsetof() in libbpf for CO-RE, from Yonghong Song.
6) Fix segfault in test_mmap due to inconsistent length params, from Jianlin Lv.
7) Don't override errno in libbpf when logging errors, from Toke Høiland-Jørgensen.
8) Fix v4_to_v6 sockaddr conversion in sk_lookup test, from Stanislav Fomichev.
9) Add link to bpf-helpers(7) man page to BPF doc, from Joe Stringer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we've copied data from the iterator we need to revert in case we
end up not sending any data.
This bug doesn't trigger with normal 'poll' based tests, because
we only feed a small chunk of data to kernel after poll indicated
POLLOUT. With blocking IO and large writes this triggers. Receiver
ends up with less data than it should get.
Fixes: 72511aab95 ("mptcp: avoid blocking in tcp_sendpages")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAl82a18THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqVbYB/9wF0ekQk66ES0PlIKkTDqDlt8hH8gN
a86yOFow3jjOWOlol1wDyCqh4i+JD0PgRPTCmXJoFYfXUsNwjRQt2ZqVgOlS0dR3
wmxxNw0i7SQ3+LDEf3Dofgk39Y5+VSQGfT3fvM8FfHWi9Mkxmswi2EwCBMx7Cqyp
lghxsJyZoeSnwfx7Wcel75NnYID1WscKUyXR6Qd240V1h7s3oAt6ZdDnYLPJnd7M
zeRSY+HgDa98HBUMmQi627douQcTtXyE5Zpx/PkkRGEOYIS/SEF8XmA2cQ0Vu8R/
R/u/htBqoV7OlL5XdyH1l2+HDOu0M1EKZiNWYMV34yobUqkrGg0oiJut
=NuYv
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.9-20200814' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2020-08-14
this is a pull request of 6 patches for net/master. All patches fix problems in
the j1939 CAN networking stack.
The first patch is by Eric Dumazet fixes a kernel-infoleak in
j1939_sk_sock2sockaddr_can().
The remaining 5 patches are by Oleksij Rempel and fix recption of j1939
messages not orginated by the stack, a use-after-free in j1939_tp_txtimer(),
ensure that the CAN driver has a ml_priv allocated. These problem were found by
google's syzbot. Further ETP sessions with block size of less than 255 are
fixed and a sanity check was added to j1939_xtp_rx_dat_one() to detect packet
corruption.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the stack relays on receiving own packets, it was overwriting own
transmit buffer from received packets.
At least theoretically, the received echo buffer can be corrupt or
changed and the session partner can request to resend previous data. In
this case we will re-send bad data.
With this patch we will stop to overwrite own TX buffer and use it for
sanity checking.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20200807105200.26441-6-o.rempel@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sometimes it makes no sense to search the skb by pkt.dpo, since we need
next the skb within the transaction block. This may happen if we have an
ETP session with CTS set to less than 255 packets.
After this patch, we will be able to work with ETP sessions where the
block size (ETP.CM_CTS byte 2) is less than 255 packets.
Reported-by: Henrique Figueira <henrislip@gmail.com>
Reported-by: https://github.com/linux-can/can-utils/issues/228
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20200807105200.26441-5-o.rempel@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds check to ensure that the struct net_device::ml_priv is
allocated, as it is used later by the j1939 stack.
The allocation is done by all mainline CAN network drivers, but when using
bond or team devices this is not the case.
Bail out if no ml_priv is allocated.
Reported-by: syzbot+f03d384f3455d28833eb@syzkaller.appspotmail.com
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20200807105200.26441-4-o.rempel@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The current stack implementation do not support ECTS requests of not
aligned TP sized blocks.
If ECTS will request a block with size and offset spanning two TP
blocks, this will cause memcpy() to read beyond the queued skb (which
does only contain one TP sized block).
Sometimes KASAN will detect this read if the memory region beyond the
skb was previously allocated and freed. In other situations it will stay
undetected. The ETP transfer in any case will be corrupted.
This patch adds a sanity check to avoid this kind of read and abort the
session with error J1939_XTP_ABORT_ECTS_TOO_BIG.
Reported-by: syzbot+5322482fe520b02aea30@syzkaller.appspotmail.com
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20200807105200.26441-3-o.rempel@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In current J1939 stack implementation, we process all locally send
messages as own messages. Even if it was send by CAN_RAW socket.
To reproduce it use following commands:
testj1939 -P -r can0:0x80 &
cansend can0 18238040#0123
This step will trigger false positive not critical warning:
j1939_simple_recv: Received already invalidated message
With this patch we add additional check to make sure, related skb is own
echo message.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20200807105200.26441-2-o.rempel@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
syzkaller reports splat:
------------[ cut here ]------------
Buffer overflow detected (80 < 137)!
Call Trace:
do_ebt_get_ctl+0x2b4/0x790 net/bridge/netfilter/ebtables.c:2317
nf_getsockopt+0x72/0xd0 net/netfilter/nf_sockopt.c:116
ip_getsockopt net/ipv4/ip_sockglue.c:1778 [inline]
caused by a copy-to-user with a too-large "*len" value.
This adds a argument check on *len just like in the non-compat version
of the handler.
Before the "Fixes" commit, the reproducer fails with -EINVAL as
expected:
1. core calls the "compat" getsockopt version
2. compat getsockopt version detects the *len value is possibly
in 64-bit layout (*len != compat_len)
3. compat getsockopt version delegates everything to native getsockopt
version
4. native getsockopt rejects invalid *len
-> compat handler only sees len == sizeof(compat_struct) for GET_ENTRIES.
After the refactor, event sequence is:
1. getsockopt calls "compat" version (len != native_len)
2. compat version attempts to copy *len bytes, where *len is random
value from userspace
Fixes: fc66de8e16 ("netfilter/ebtables: clean up compat {get, set}sockopt handling")
Reported-by: syzbot+5accb5c62faa1d346480@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
"Some merge window fallout, some longer term fixes:
1) Handle headroom properly in lapbether and x25_asy drivers, from
Xie He.
2) Fetch MAC address from correct r8152 device node, from Thierry
Reding.
3) In the sw kTLS path we should allow MSG_CMSG_COMPAT in sendmsg,
from Rouven Czerwinski.
4) Correct fdputs in socket layer, from Miaohe Lin.
5) Revert troublesome sockptr_t optimization, from Christoph Hellwig.
6) Fix TCP TFO key reading on big endian, from Jason Baron.
7) Missing CAP_NET_RAW check in nfc, from Qingyu Li.
8) Fix inet fastreuse optimization with tproxy sockets, from Tim
Froidcoeur.
9) Fix 64-bit divide in new SFC driver, from Edward Cree.
10) Add a tracepoint for prandom_u32 so that we can more easily
perform usage analysis. From Eric Dumazet.
11) Fix rwlock imbalance in AF_PACKET, from John Ogness"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (49 commits)
net: openvswitch: introduce common code for flushing flows
af_packet: TPACKET_V3: fix fill status rwlock imbalance
random32: add a tracepoint for prandom_u32()
Revert "ipv4: tunnel: fix compilation on ARCH=um"
net: accept an empty mask in /sys/class/net/*/queues/rx-*/rps_cpus
net: ethernet: stmmac: Disable hardware multicast filter
net: stmmac: dwmac1000: provide multicast filter fallback
ipv4: tunnel: fix compilation on ARCH=um
vsock: fix potential null pointer dereference in vsock_poll()
sfc: fix ef100 design-param checking
net: initialize fastreuse on inet_inherit_port
net: refactor bind_bucket fastreuse into helper
net: phy: marvell10g: fix null pointer dereference
net: Fix potential memory leak in proto_register()
net: qcom/emac: add missed clk_disable_unprepare in error path of emac_clks_phase1_init
ionic_lif: Use devm_kcalloc() in ionic_qcq_alloc()
net/nfc/rawsock.c: add CAP_NET_RAW check.
hinic: fix strncpy output truncated compile warnings
drivers/net/wan/x25_asy: Added needed_headroom and a skb->len check
net/tls: Fix kmap usage
...
To avoid some issues, for example RCU usage warning and double free,
we should flush the flows under ovs_lock. This patch refactors
table_instance_destroy and introduces table_instance_flow_flush
which can be invoked by __dp_destroy or ovs_flow_tbl_flush.
Fixes: 50b0e61b32 ("net: openvswitch: fix possible memleak on destroy flow-table")
Reported-by: Johan Knöös <jknoos@google.com>
Reported-at: https://mail.openvswitch.org/pipermail/ovs-discuss/2020-August/050489.html
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After @blk_fill_in_prog_lock is acquired there is an early out vnet
situation that can occur. In that case, the rwlock needs to be
released.
Also, since @blk_fill_in_prog_lock is only acquired when @tp_version
is exactly TPACKET_V3, only release it on that exact condition as
well.
And finally, add sparse annotation so that it is clearer that
prb_fill_curr_block() and prb_clear_blk_fill_status() are acquiring
and releasing @blk_fill_in_prog_lock, respectively. sparse is still
unable to understand the balance, but the warnings are now on a
higher level that make more sense.
Fixes: 632ca50f2c ("af_packet: TPACKET_V3: replace busy-wait loop")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to patch ("bpf: sock_ops ctx access may stomp registers") if the
src_reg = dst_reg when reading the sk field of a sock_ops struct we
generate xlated code,
53: (61) r9 = *(u32 *)(r9 +28)
54: (15) if r9 == 0x0 goto pc+3
56: (79) r9 = *(u64 *)(r9 +0)
This stomps on the r9 reg to do the sk_fullsock check and then when
reading the skops->sk field instead of the sk pointer we get the
sk_fullsock. To fix use similar pattern noted in the previous fix
and use the temp field to save/restore a register used to do
sk_fullsock check.
After the fix the generated xlated code reads,
52: (7b) *(u64 *)(r9 +32) = r8
53: (61) r8 = *(u32 *)(r9 +28)
54: (15) if r9 == 0x0 goto pc+3
55: (79) r8 = *(u64 *)(r9 +32)
56: (79) r9 = *(u64 *)(r9 +0)
57: (05) goto pc+1
58: (79) r8 = *(u64 *)(r9 +32)
Here r9 register was in-use so r8 is chosen as the temporary register.
In line 52 r8 is saved in temp variable and at line 54 restored in case
fullsock != 0. Finally we handle fullsock == 0 case by restoring at
line 58.
This adds a new macro SOCK_OPS_GET_SK it is almost possible to merge
this with SOCK_OPS_GET_FIELD, but I found the extra branch logic a
bit more confusing than just adding a new macro despite a bit of
duplicating code.
Fixes: 1314ef5611 ("bpf: export bpf_sock for BPF_PROG_TYPE_SOCK_OPS prog type")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/159718349653.4728.6559437186853473612.stgit@john-Precision-5820-Tower
I had a sockmap program that after doing some refactoring started spewing
this splat at me:
[18610.807284] BUG: unable to handle kernel NULL pointer dereference at 0000000000000001
[...]
[18610.807359] Call Trace:
[18610.807370] ? 0xffffffffc114d0d5
[18610.807382] __cgroup_bpf_run_filter_sock_ops+0x7d/0xb0
[18610.807391] tcp_connect+0x895/0xd50
[18610.807400] tcp_v4_connect+0x465/0x4e0
[18610.807407] __inet_stream_connect+0xd6/0x3a0
[18610.807412] ? __inet_stream_connect+0x5/0x3a0
[18610.807417] inet_stream_connect+0x3b/0x60
[18610.807425] __sys_connect+0xed/0x120
After some debugging I was able to build this simple reproducer,
__section("sockops/reproducer_bad")
int bpf_reproducer_bad(struct bpf_sock_ops *skops)
{
volatile __maybe_unused __u32 i = skops->snd_ssthresh;
return 0;
}
And along the way noticed that below program ran without splat,
__section("sockops/reproducer_good")
int bpf_reproducer_good(struct bpf_sock_ops *skops)
{
volatile __maybe_unused __u32 i = skops->snd_ssthresh;
volatile __maybe_unused __u32 family;
compiler_barrier();
family = skops->family;
return 0;
}
So I decided to check out the code we generate for the above two
programs and noticed each generates the BPF code you would expect,
0000000000000000 <bpf_reproducer_bad>:
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
0: r1 = *(u32 *)(r1 + 96)
1: *(u32 *)(r10 - 4) = r1
; return 0;
2: r0 = 0
3: exit
0000000000000000 <bpf_reproducer_good>:
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
0: r2 = *(u32 *)(r1 + 96)
1: *(u32 *)(r10 - 4) = r2
; family = skops->family;
2: r1 = *(u32 *)(r1 + 20)
3: *(u32 *)(r10 - 8) = r1
; return 0;
4: r0 = 0
5: exit
So we get reasonable assembly, but still something was causing the null
pointer dereference. So, we load the programs and dump the xlated version
observing that line 0 above 'r* = *(u32 *)(r1 +96)' is going to be
translated by the skops access helpers.
int bpf_reproducer_bad(struct bpf_sock_ops * skops):
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
0: (61) r1 = *(u32 *)(r1 +28)
1: (15) if r1 == 0x0 goto pc+2
2: (79) r1 = *(u64 *)(r1 +0)
3: (61) r1 = *(u32 *)(r1 +2340)
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
4: (63) *(u32 *)(r10 -4) = r1
; return 0;
5: (b7) r0 = 0
6: (95) exit
int bpf_reproducer_good(struct bpf_sock_ops * skops):
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
0: (61) r2 = *(u32 *)(r1 +28)
1: (15) if r2 == 0x0 goto pc+2
2: (79) r2 = *(u64 *)(r1 +0)
3: (61) r2 = *(u32 *)(r2 +2340)
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
4: (63) *(u32 *)(r10 -4) = r2
; family = skops->family;
5: (79) r1 = *(u64 *)(r1 +0)
6: (69) r1 = *(u16 *)(r1 +16)
; family = skops->family;
7: (63) *(u32 *)(r10 -8) = r1
; return 0;
8: (b7) r0 = 0
9: (95) exit
Then we look at lines 0 and 2 above. In the good case we do the zero
check in r2 and then load 'r1 + 0' at line 2. Do a quick cross-check
into the bpf_sock_ops check and we can confirm that is the 'struct
sock *sk' pointer field. But, in the bad case,
0: (61) r1 = *(u32 *)(r1 +28)
1: (15) if r1 == 0x0 goto pc+2
2: (79) r1 = *(u64 *)(r1 +0)
Oh no, we read 'r1 +28' into r1, this is skops->fullsock and then in
line 2 we read the 'r1 +0' as a pointer. Now jumping back to our spat,
[18610.807284] BUG: unable to handle kernel NULL pointer dereference at 0000000000000001
The 0x01 makes sense because that is exactly the fullsock value. And
its not a valid dereference so we splat.
To fix we need to guard the case when a program is doing a sock_ops field
access with src_reg == dst_reg. This is already handled in the load case
where the ctx_access handler uses a tmp register being careful to
store the old value and restore it. To fix the get case test if
src_reg == dst_reg and in this case do the is_fullsock test in the
temporary register. Remembering to restore the temporary register before
writing to either dst_reg or src_reg to avoid smashing the pointer into
the struct holding the tmp variable.
Adding this inline code to test_tcpbpf_kern will now be generated
correctly from,
9: r2 = *(u32 *)(r2 + 96)
to xlated code,
12: (7b) *(u64 *)(r2 +32) = r9
13: (61) r9 = *(u32 *)(r2 +28)
14: (15) if r9 == 0x0 goto pc+4
15: (79) r9 = *(u64 *)(r2 +32)
16: (79) r2 = *(u64 *)(r2 +0)
17: (61) r2 = *(u32 *)(r2 +2348)
18: (05) goto pc+1
19: (79) r9 = *(u64 *)(r2 +32)
And in the normal case we keep the original code, because really this
is an edge case. From this,
9: r2 = *(u32 *)(r6 + 96)
to xlated code,
22: (61) r2 = *(u32 *)(r6 +28)
23: (15) if r2 == 0x0 goto pc+2
24: (79) r2 = *(u64 *)(r6 +0)
25: (61) r2 = *(u32 *)(r2 +2348)
So three additional instructions if dst == src register, but I scanned
my current code base and did not see this pattern anywhere so should
not be a big deal. Further, it seems no one else has hit this or at
least reported it so it must a fairly rare pattern.
Fixes: 9b1f3d6e5a ("bpf: Refactor sock_ops_convert_ctx_access")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/159718347772.4728.2781381670567919577.stgit@john-Precision-5820-Tower
syzbot found a memory leak in nf_tables_addchain() because the chain
object is not free'd correctly on error.
Fixes: d0e2c7de92 ("netfilter: nf_tables: add NFT_CHAIN_BINDING")
Reported-by: syzbot+c99868fde67014f7e9f5@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_ct_frag6_gather is part of nf_defrag_ipv6.ko, not ipv6 core.
The current use of the netfilter ipv6 stub indirections causes a module
dependency between ipv6 and nf_defrag_ipv6.
This prevents nf_defrag_ipv6 module from being removed because ipv6 can't
be unloaded.
Remove the indirection and always use a direct call. This creates a
depency from nf_conntrack_bridge to nf_defrag_ipv6 instead:
modinfo nf_conntrack
depends: nf_conntrack,nf_defrag_ipv6,bridge
.. and nf_conntrack already depends on nf_defrag_ipv6 anyway.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Enforce XDP_FLAGS_UPDATE_IF_NOEXIST only if new BPF program to be attached is
non-NULL (i.e., we are not detaching a BPF program).
Fixes: d4baa9368a ("bpf, xdp: Extract common XDP program attachment logic")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200812022923.1217922-1-andriin@fb.com
This reverts commit 06a7a37be5.
The bug was already fixed, this added a dup include.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must accept an empty mask in store_rps_map(), or we are not able
to disable RPS on a queue.
Fixes: 07bbecb341 ("net: Restrict receive packets queuing to housekeeping CPUs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Cc: Alex Belits <abelits@marvell.com>
Cc: Nitesh Narayan Lal <nitesh@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With certain configurations, a 64-bit ARCH=um errors
out here with an unknown csum_ipv6_magic() function.
Include the right header file to always have it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported this issue where in the vsock_poll() we find the
socket state at TCP_ESTABLISHED, but 'transport' is null:
general protection fault, probably for non-canonical address 0xdffffc0000000012: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097]
CPU: 0 PID: 8227 Comm: syz-executor.2 Not tainted 5.8.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:vsock_poll+0x75a/0x8e0 net/vmw_vsock/af_vsock.c:1038
Call Trace:
sock_poll+0x159/0x460 net/socket.c:1266
vfs_poll include/linux/poll.h:90 [inline]
do_pollfd fs/select.c:869 [inline]
do_poll fs/select.c:917 [inline]
do_sys_poll+0x607/0xd40 fs/select.c:1011
__do_sys_poll fs/select.c:1069 [inline]
__se_sys_poll fs/select.c:1057 [inline]
__x64_sys_poll+0x18c/0x440 fs/select.c:1057
do_syscall_64+0x60/0xe0 arch/x86/entry/common.c:384
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This issue can happen if the TCP_ESTABLISHED state is set after we read
the vsk->transport in the vsock_poll().
We could put barriers to synchronize, but this can only happen during
connection setup, so we can simply check that 'transport' is valid.
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Reported-and-tested-by: syzbot+a61bac2fcc1a7c6623fe@syzkaller.appspotmail.com
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sent to all available MDSes once per second now. Other than that, we
have a lot of fixes and cleanups all around the filesystem, including
a tweak to cut down on MDS request resends in multi-MDS setups from
Yanhu and fixups for SELinux symlink labeling and MClientSession
message decoding from Jeff.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAl80I3MTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi7rlB/4/tegnfsB+O6MQPt+DkSxjQ6+90J/O
aDj3jnwHoUBUitTP92wHdy/TanlZMX0UQqq4caWt1Ot0Rveb6XTfTIzEDtG2ejYQ
dcH6LB3dS9Qvjrwh7oRawx8Xux/RdIIA99OvAX7K+4IeLKP5PjmwfdM1Mm0agfoS
V8qXm8cGyqF2lWown092Znr8s6OSsDEaUbjB2tlz5msWeK9rSFD5bDYOBdOTkBCU
5v5BIUwWWoU9YFMWDJgVNS5l2Scq5yTDEleZcCCJMovKNrhBi9DcwUDKrDQJ3+5v
UmfI5M/L99Ng7yAcPqbeOZ1HibuOrdmqAoR6lCiD+PPEPrf99rVLRinQ
=2NtI
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.9-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"Xiubo has completed his work on filesystem client metrics, they are
sent to all available MDSes once per second now.
Other than that, we have a lot of fixes and cleanups all around the
filesystem, including a tweak to cut down on MDS request resends in
multi-MDS setups from Yanhu and fixups for SELinux symlink labeling
and MClientSession message decoding from Jeff"
* tag 'ceph-for-5.9-rc1' of git://github.com/ceph/ceph-client: (22 commits)
ceph: handle zero-length feature mask in session messages
ceph: use frag's MDS in either mode
ceph: move sb->wb_pagevec_pool to be a global mempool
ceph: set sec_context xattr on symlink creation
ceph: remove redundant initialization of variable mds
ceph: fix use-after-free for fsc->mdsc
ceph: remove unused variables in ceph_mdsmap_decode()
ceph: delete repeated words in fs/ceph/
ceph: send client provided metric flags in client metadata
ceph: periodically send perf metrics to MDSes
ceph: check the sesion state and return false in case it is closed
libceph: replace HTTP links with HTTPS ones
ceph: remove unnecessary cast in kfree()
libceph: just have osd_req_op_init() return a pointer
ceph: do not access the kiocb after aio requests
ceph: clean up and optimize ceph_check_delayed_caps()
ceph: fix potential mdsc use-after-free crash
ceph: switch to WARN_ON_ONCE in encode_supported_features()
ceph: add global total_caps to count the mdsc's total caps number
ceph: add check_session_state() helper and make it global
...
In the case of TPROXY, bind_conflict optimizations for SO_REUSEADDR or
SO_REUSEPORT are broken, possibly resulting in O(n) instead of O(1) bind
behaviour or in the incorrect reuse of a bind.
the kernel keeps track for each bind_bucket if all sockets in the
bind_bucket support SO_REUSEADDR or SO_REUSEPORT in two fastreuse flags.
These flags allow skipping the costly bind_conflict check when possible
(meaning when all sockets have the proper SO_REUSE option).
For every socket added to a bind_bucket, these flags need to be updated.
As soon as a socket that does not support reuse is added, the flag is
set to false and will never go back to true, unless the bind_bucket is
deleted.
Note that there is no mechanism to re-evaluate these flags when a socket
is removed (this might make sense when removing a socket that would not
allow reuse; this leaves room for a future patch).
For this optimization to work, it is mandatory that these flags are
properly initialized and updated.
When a child socket is created from a listen socket in
__inet_inherit_port, the TPROXY case could create a new bind bucket
without properly initializing these flags, thus preventing the
optimization to work. Alternatively, a socket not allowing reuse could
be added to an existing bind bucket without updating the flags, causing
bind_conflict to never be called as it should.
Call inet_csk_update_fastreuse when __inet_inherit_port decides to create
a new bind_bucket or use a different bind_bucket than the one of the
listen socket.
Fixes: 093d282321 ("tproxy: fix hash locking issue when using port redirection in __inet_inherit_port()")
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Tim Froidcoeur <tim.froidcoeur@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the fastreuse update code in inet_csk_get_port into a small
helper function that can be called from other places.
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Tim Froidcoeur <tim.froidcoeur@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we failed to assign proto idx, we free the twsk_slab_name but forget to
free the twsk_slab. Add a helper function tw_prot_cleanup() to free these
together and also use this helper function in proto_unregister().
Fixes: b45ce32135 ("sock: fix potential memory leak in proto_register()")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a raw AF_NFC socket, CAP_NET_RAW needs to be checked first.
Signed-off-by: Qingyu Li <ieatmuttonchuan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When MSG_OOB is specified to tls_device_sendpage() the mapped page is
never unmapped.
Hold off mapping the page until after the flags are checked and the page
is actually needed.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Untangle the header spaghetti which causes build failures in various
situations caused by the lockdep additions to seqcount to validate that
the write side critical sections are non-preemptible.
- The seqcount associated lock debug addons which were blocked by the
above fallout.
seqcount writers contrary to seqlock writers must be externally
serialized, which usually happens via locking - except for strict per
CPU seqcounts. As the lock is not part of the seqcount, lockdep cannot
validate that the lock is held.
This new debug mechanism adds the concept of associated locks.
sequence count has now lock type variants and corresponding
initializers which take a pointer to the associated lock used for
writer serialization. If lockdep is enabled the pointer is stored and
write_seqcount_begin() has a lockdep assertion to validate that the
lock is held.
Aside of the type and the initializer no other code changes are
required at the seqcount usage sites. The rest of the seqcount API is
unchanged and determines the type at compile time with the help of
_Generic which is possible now that the minimal GCC version has been
moved up.
Adding this lockdep coverage unearthed a handful of seqcount bugs which
have been addressed already independent of this.
While generaly useful this comes with a Trojan Horse twist: On RT
kernels the write side critical section can become preemtible if the
writers are serialized by an associated lock, which leads to the well
known reader preempts writer livelock. RT prevents this by storing the
associated lock pointer independent of lockdep in the seqcount and
changing the reader side to block on the lock when a reader detects
that a writer is in the write side critical section.
- Conversion of seqcount usage sites to associated types and initializers.
-----BEGIN PGP SIGNATURE-----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=7Gj+
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2020-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Thomas Gleixner:
"A set of locking fixes and updates:
- Untangle the header spaghetti which causes build failures in
various situations caused by the lockdep additions to seqcount to
validate that the write side critical sections are non-preemptible.
- The seqcount associated lock debug addons which were blocked by the
above fallout.
seqcount writers contrary to seqlock writers must be externally
serialized, which usually happens via locking - except for strict
per CPU seqcounts. As the lock is not part of the seqcount, lockdep
cannot validate that the lock is held.
This new debug mechanism adds the concept of associated locks.
sequence count has now lock type variants and corresponding
initializers which take a pointer to the associated lock used for
writer serialization. If lockdep is enabled the pointer is stored
and write_seqcount_begin() has a lockdep assertion to validate that
the lock is held.
Aside of the type and the initializer no other code changes are
required at the seqcount usage sites. The rest of the seqcount API
is unchanged and determines the type at compile time with the help
of _Generic which is possible now that the minimal GCC version has
been moved up.
Adding this lockdep coverage unearthed a handful of seqcount bugs
which have been addressed already independent of this.
While generally useful this comes with a Trojan Horse twist: On RT
kernels the write side critical section can become preemtible if
the writers are serialized by an associated lock, which leads to
the well known reader preempts writer livelock. RT prevents this by
storing the associated lock pointer independent of lockdep in the
seqcount and changing the reader side to block on the lock when a
reader detects that a writer is in the write side critical section.
- Conversion of seqcount usage sites to associated types and
initializers"
* tag 'locking-urgent-2020-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
locking/seqlock, headers: Untangle the spaghetti monster
locking, arch/ia64: Reduce <asm/smp.h> header dependencies by moving XTP bits into the new <asm/xtp.h> header
x86/headers: Remove APIC headers from <asm/smp.h>
seqcount: More consistent seqprop names
seqcount: Compress SEQCNT_LOCKNAME_ZERO()
seqlock: Fold seqcount_LOCKNAME_init() definition
seqlock: Fold seqcount_LOCKNAME_t definition
seqlock: s/__SEQ_LOCKDEP/__SEQ_LOCK/g
hrtimer: Use sequence counter with associated raw spinlock
kvm/eventfd: Use sequence counter with associated spinlock
userfaultfd: Use sequence counter with associated spinlock
NFSv4: Use sequence counter with associated spinlock
iocost: Use sequence counter with associated spinlock
raid5: Use sequence counter with associated spinlock
vfs: Use sequence counter with associated spinlock
timekeeping: Use sequence counter with associated raw spinlock
xfrm: policy: Use sequence counters with associated lock
netfilter: nft_set_rbtree: Use sequence counter with associated rwlock
netfilter: conntrack: Use sequence counter with associated spinlock
sched: tasks: Use sequence counter with associated spinlock
...
When TFO keys are read back on big endian systems either via the global
sysctl interface or via getsockopt() using TCP_FASTOPEN_KEY, the values
don't match what was written.
For example, on s390x:
# echo "1-2-3-4" > /proc/sys/net/ipv4/tcp_fastopen_key
# cat /proc/sys/net/ipv4/tcp_fastopen_key
02000000-01000000-04000000-03000000
Instead of:
# cat /proc/sys/net/ipv4/tcp_fastopen_key
00000001-00000002-00000003-00000004
Fix this by converting to the correct endianness on read. This was
reported by Colin Ian King when running the 'tcp_fastopen_backup_key' net
selftest on s390x, which depends on the read value matching what was
written. I've confirmed that the test now passes on big and little endian
systems.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Fixes: 438ac88009 ("net: fastopen: robustness and endianness fixes for SipHash")
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Eric Dumazet <edumazet@google.com>
Reported-and-tested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commits 6d04fe15f7 and
a31edb2059.
It turns out the idea to share a single pointer for both kernel and user
space address causes various kinds of problems. So use the slightly less
optimal version that uses an extra bit, but which is guaranteed to be safe
everywhere.
Fixes: 6d04fe15f7 ("net: optimize the sockptr_t for unified kernel/user address spaces")
Reported-by: Eric Dumazet <edumazet@google.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: CPU: 1 PID: 16059 at lib/refcount.c:31 refcount_warn_saturate+0xdf/0xf
[..]
__nft_mt_tg_destroy+0x42/0x50 [nft_compat]
nft_target_destroy+0x63/0x80 [nft_compat]
nf_tables_expr_destroy+0x1b/0x30 [nf_tables]
nf_tables_rule_destroy+0x3a/0x70 [nf_tables]
nf_tables_exit_net+0x186/0x3d0 [nf_tables]
Happens when a compat expr is destoyed from abort path.
There is no functional impact; after this work queue is flushed
unconditionally if its pending.
This removes the waitcount optimization. Test of repeated
iptables-restore of a ~60k kubernetes ruleset doesn't indicate
a slowdown. In case the counter is needed after all for some workloads
we can revert this and increment the refcount for the
!= NFT_PREPARE_TRANS case to avoid the increment/decrement imbalance.
While at it, also flush for match case, this was an oversight
in the original patch.
Fixes: ffe8923f10 ("netfilter: nft_compat: make sure xtables destructors have run")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On big-endian machine, the returned register data when the exthdr is
present is not being compared correctly because little-endian is
assumed. The function nft_cmp_fast_mask(), called by nft_cmp_fast_eval()
and nft_cmp_fast_init(), calls cpu_to_le32().
The following dump also shows that little endian is assumed:
$ nft --debug=netlink add rule ip recordroute forward ip option rr exists counter
ip
[ exthdr load ipv4 1b @ 7 + 0 present => reg 1 ]
[ cmp eq reg 1 0x01000000 ]
[ counter pkts 0 bytes 0 ]
Lastly, debug print in nft_cmp_fast_init() and nft_cmp_fast_eval() when
RR option exists in the packet shows that the comparison fails because
the assumption:
nft_cmp_fast_init:189 priv->sreg=4 desc.len=8 mask=0xff000000 data.data[0]=0x10003e0
nft_cmp_fast_eval:57 regs->data[priv->sreg=4]=0x1 mask=0xff000000 priv->data=0x1000000
v2: use nft_reg_store8() instead (Florian Westphal). Also to avoid the
warnings reported by kernel test robot.
Fixes: dbb5281a1f ("netfilter: nf_tables: add support for matching IPv4 options")
Fixes: c078ca3b0c ("netfilter: nft_exthdr: Add support for existence check")
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
- Support for user extended attributes on NFS (RFC 8276)
- Further reduce unnecessary NFSv4 delegation recalls
Notable fixes:
- Fix recent krb5p regression
- Address a few resource leaks and a rare NULL dereference
Other:
- De-duplicate RPC/RDMA error handling and other utility functions
- Replace storage and display of kernel memory addresses by tracepoints
-----BEGIN PGP SIGNATURE-----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=OEpF
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.9' of git://git.linux-nfs.org/projects/cel/cel-2.6
Pull NFS server updates from Chuck Lever:
"Highlights:
- Support for user extended attributes on NFS (RFC 8276)
- Further reduce unnecessary NFSv4 delegation recalls
Notable fixes:
- Fix recent krb5p regression
- Address a few resource leaks and a rare NULL dereference
Other:
- De-duplicate RPC/RDMA error handling and other utility functions
- Replace storage and display of kernel memory addresses by tracepoints"
* tag 'nfsd-5.9' of git://git.linux-nfs.org/projects/cel/cel-2.6: (38 commits)
svcrdma: CM event handler clean up
svcrdma: Remove transport reference counting
svcrdma: Fix another Receive buffer leak
SUNRPC: Refresh the show_rqstp_flags() macro
nfsd: netns.h: delete a duplicated word
SUNRPC: Fix ("SUNRPC: Add "@len" parameter to gss_unwrap()")
nfsd: avoid a NULL dereference in __cld_pipe_upcall()
nfsd4: a client's own opens needn't prevent delegations
nfsd: Use seq_putc() in two functions
svcrdma: Display chunk completion ID when posting a rw_ctxt
svcrdma: Record send_ctxt completion ID in trace_svcrdma_post_send()
svcrdma: Introduce Send completion IDs
svcrdma: Record Receive completion ID in svc_rdma_decode_rqst
svcrdma: Introduce Receive completion IDs
svcrdma: Introduce infrastructure to support completion IDs
svcrdma: Add common XDR encoders for RDMA and Read segments
svcrdma: Add common XDR decoders for RDMA and Read segments
SUNRPC: Add helpers for decoding list discriminators symbolically
svcrdma: Remove declarations for functions long removed
svcrdma: Clean up trace_svcrdma_send_failed() tracepoint
...
Convert the uses of fallthrough comments to fallthrough macro.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper function ip_is_fragment() to check ip fragment.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The out_fs jump label has nothing to do but goto out.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should fput() file iff FDPUT_FPUT is set. So we should set fput_needed
accordingly.
Fixes: 00e188ef6a ("sockfd_lookup_light(): switch to fdget^W^Waway from fget_light")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper function fdput() to fput() the file iff FDPUT_FPUT is set.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_INET_XFRM_TUNNEL is set but CONFIG_IPV6 is n,
net/ipv4/ip_vti.c:493:27: warning: 'vti_ipip6_handler' defined but not used [-Wunused-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Trying to use ktls on a system with 32-bit userspace and 64-bit kernel
results in a EOPNOTSUPP message during sendmsg:
setsockopt(3, SOL_TLS, TLS_TX, …, 40) = 0
sendmsg(3, …, msg_flags=0}, 0) = -1 EOPNOTSUPP (Operation not supported)
The tls_sw implementation does strict flag checking and does not allow
the MSG_CMSG_COMPAT flag, which is set if the message comes in through
the compat syscall.
This patch adds MSG_CMSG_COMPAT to the flag check to allow the usage of
the TLS SW implementation on systems using the compat syscall path.
Note that the same check is present in the sendmsg path for the TLS
device implementation, however the flag hasn't been added there for lack
of testing hardware.
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2020-08-08
The following pull-request contains BPF updates for your *net* tree.
We've added 11 non-merge commits during the last 2 day(s) which contain
a total of 24 files changed, 216 insertions(+), 135 deletions(-).
The main changes are:
1) Fix UAPI for BPF map iterator before it gets frozen to allow for more
extensions/customization in future, from Yonghong Song.
2) Fix selftests build to undo verbose build output, from Andrii Nakryiko.
3) Fix inlining compilation error on bpf_do_trace_printk() due to variable
argument lists, from Stanislav Fomichev.
4) Fix an uninitialized pointer warning at btf__parse_raw() in libbpf,
from Daniel T. Lee.
5) Fix several compilation warnings in selftests with regards to ignoring
return value, from Jianlin Lv.
6) Fix interruptions by switching off timeout for BPF tests, from Jiri Benc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit b93df08ccd ("mptcp: explicitly track the fully
established status"), the status of unaccepted mptcp closed in
mptcp_sock_destruct() changes from TCP_SYN_RECV to TCP_ESTABLISHED.
As a result mptcp_sock_destruct() does not perform the proper
cleanup and inet_sock_destruct() will later emit a warn.
Address the issue updating the condition tested in mptcp_sock_destruct().
Also update the related comment.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/66
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Fixes: b93df08ccd ("mptcp: explicitly track the fully established status")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=5TFR
-----END PGP SIGNATURE-----
Merge tag 'seccomp-v5.9-rc1-fix1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp fix from Kees Cook:
"This fixes my typo in the SCM_RIGHTS refactoring that broke compat
handling.
Thanks to Thadeu Lima de Souza Cascardo for tracking it down, and to
Christian Zigotzky and Alex Xu for their reports"
* tag 'seccomp-v5.9-rc1-fix1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
net/scm: Fix typo in SCM_RIGHTS compat refactoring
When refactoring the SCM_RIGHTS code, I accidentally mis-merged my
native/compat diffs, which entirely broke using SCM_RIGHTS in compat
mode. Use the correct helper.
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Link: https://lists.ozlabs.org/pipermail/linuxppc-dev/2020-August/216156.html
Reported-by: "Alex Xu (Hello71)" <alex_y_xu@yahoo.ca>
Link: https://lore.kernel.org/lkml/1596812929.lz7fuo8r2w.none@localhost/
Suggested-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Fixes: c0029de509 ("net/scm: Regularize compat handling of scm_detach_fds()")
Tested-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Merge misc updates from Andrew Morton:
- a few MM hotfixes
- kthread, tools, scripts, ntfs and ocfs2
- some of MM
Subsystems affected by this patch series: kthread, tools, scripts, ntfs,
ocfs2 and mm (hofixes, pagealloc, slab-generic, slab, slub, kcsan,
debug, pagecache, gup, swap, shmem, memcg, pagemap, mremap, mincore,
sparsemem, vmalloc, kasan, pagealloc, hugetlb and vmscan).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (162 commits)
mm: vmscan: consistent update to pgrefill
mm/vmscan.c: fix typo
khugepaged: khugepaged_test_exit() check mmget_still_valid()
khugepaged: retract_page_tables() remember to test exit
khugepaged: collapse_pte_mapped_thp() protect the pmd lock
khugepaged: collapse_pte_mapped_thp() flush the right range
mm/hugetlb: fix calculation of adjust_range_if_pmd_sharing_possible
mm: thp: replace HTTP links with HTTPS ones
mm/page_alloc: fix memalloc_nocma_{save/restore} APIs
mm/page_alloc.c: skip setting nodemask when we are in interrupt
mm/page_alloc: fallbacks at most has 3 elements
mm/page_alloc: silence a KASAN false positive
mm/page_alloc.c: remove unnecessary end_bitidx for [set|get]_pfnblock_flags_mask()
mm/page_alloc.c: simplify pageblock bitmap access
mm/page_alloc.c: extract the common part in pfn_to_bitidx()
mm/page_alloc.c: replace the definition of NR_MIGRATETYPE_BITS with PB_migratetype_bits
mm/shuffle: remove dynamic reconfiguration
mm/memory_hotplug: document why shuffle_zone() is relevant
mm/page_alloc: remove nr_free_pagecache_pages()
mm: remove vm_total_pages
...
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This set includes a some improvements to the dlm
networking layer: improving the ability to trace
dlm messages for debugging, and improved handling
of bad messages or disrupted connections.
-----BEGIN PGP SIGNATURE-----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=qgti
-----END PGP SIGNATURE-----
Merge tag 'dlm-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm updates from David Teigland:
"This set includes a some improvements to the dlm networking layer:
improving the ability to trace dlm messages for debugging, and
improved handling of bad messages or disrupted connections"
* tag 'dlm-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
fs: dlm: implement tcp graceful shutdown
fs: dlm: change handling of reconnects
fs: dlm: don't close socket on invalid message
fs: dlm: set skb mark per peer socket
fs: dlm: set skb mark for listen socket
net: sock: add sock_set_mark
dlm: Fix kobject memleak
drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events, temperature
and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8q7tsACgkQqDIjiipP
6E+5Rwf7BFEn5YXPvng8cmnAlgvEBc9DdT6mGSo0NpFm9MdUxXlaqvw3WWSGyqWQ
+z0Ka7lmn5XyiMsVN11++Snp+79X17HzZf9SXO3glyIpAn+5prTDRhzzj0/jPrtS
sEeI++DrILsKKMGVljzftLmwNJN9DkUDNcnmWmZdCDbYVEKtP9Pjf2wBjAnXj7sX
JA3CkHRMwYLEQbfaKz37M11cYM+LqbDOlb6U11YWgAGGJ7d7zNYRf2/YSYPM4AN6
iE6j0E+3jIlXesULsap1AzeJaBq+wFxj1FL2TUZ8KscvRrm3AucqzNAT2M/Bc5Az
XLKKzc6Gp9JfqB5KXhX2EDu7VRnDBg==
=cSMN
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add support to enable/disable the thermal zones resulting on core
code and drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events,
temperature and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian
Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz
Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
* tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (40 commits)
thermal: intel: intel_pch_thermal: Add Cannon Lake Low Power PCH support
thermal: mediatek: Add tsensor support for V2 thermal system
thermal: mediatek: Prepare to add support for other platforms
thermal: Update power allocator and devfreq cooling to SPDX licensing
MAINTAINERS: update entry to thermal governors file name prefixing
thermal: core: Add thermal zone enable/disable notification
thermal: qcom: tsens-v0_1: Add support for MSM8939
dt-bindings: tsens: qcom: Document MSM8939 compatible
thermal: core: Fix thermal zone lookup by ID
thermal: int340x: processor_thermal: fix: update Jasper Lake PCI id
thermal: imx8mm: Support module autoloading
thermal: ti-soc-thermal: Fix reversed condition in ti_thermal_expose_sensor()
MAINTAINERS: Add maintenance information for IPA
thermal: rcar_gen3_thermal: Do not shadow thcode variable
dt-bindings: thermal: Get rid of thermal.txt and replace references
thermal: core: Move initialization after core initcall
thermal: netlink: Improve the initcall ordering
net: genetlink: Move initialization to core_initcall
thermal: rcar_gen3_thermal: Add r8a774e1 support
thermal/drivers/clock_cooling: Remove clock_cooling code
...
Commit a5cbe05a66 ("bpf: Implement bpf iterator for
map elements") added bpf iterator support for
map elements. The map element bpf iterator requires
info to identify a particular map. In the above
commit, the attr->link_create.target_fd is used
to carry map_fd and an enum bpf_iter_link_info
is added to uapi to specify the target_fd actually
representing a map_fd:
enum bpf_iter_link_info {
BPF_ITER_LINK_UNSPEC = 0,
BPF_ITER_LINK_MAP_FD = 1,
MAX_BPF_ITER_LINK_INFO,
};
This is an extensible approach as we can grow
enumerator for pid, cgroup_id, etc. and we can
unionize target_fd for pid, cgroup_id, etc.
But in the future, there are chances that
more complex customization may happen, e.g.,
for tasks, it could be filtered based on
both cgroup_id and user_id.
This patch changed the uapi to have fields
__aligned_u64 iter_info;
__u32 iter_info_len;
for additional iter_info for link_create.
The iter_info is defined as
union bpf_iter_link_info {
struct {
__u32 map_fd;
} map;
};
So future extension for additional customization
will be easier. The bpf_iter_link_info will be
passed to target callback to validate and generic
bpf_iter framework does not need to deal it any
more.
Note that map_fd = 0 will be considered invalid
and -EBADF will be returned to user space.
Fixes: a5cbe05a66 ("bpf: Implement bpf iterator for map elements")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200805055056.1457463-1-yhs@fb.com
This patch adds a new socket helper function to set the mark value for a
kernel socket.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
