Simplify the loop in phy_supported_speeds().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib has some undesirable behaviour when forcing a link mode through
ethtool. phylib uses this code:
idx = phy_find_valid(phy_find_setting(phydev->speed, phydev->duplex),
features);
to find an index in the settings table. phy_find_setting() starts at
index 0, and scans upwards looking for an exact speed and duplex match.
When it doesn't find it, it returns MAX_NUM_SETTINGS - 1, which is
10baseT-Half duplex.
phy_find_valid() then scans from the point (and effectively only checks
one entry) before bailing out, returning MAX_NUM_SETTINGS - 1.
phy_sanitize_settings() then sets ->speed to SPEED_10 and ->duplex to
DUPLEX_HALF whether or not 10baseT-Half is supported or not. This goes
against all the comments against these functions, and 10baseT-Half may
not even be supported by the hardware.
Rework these functions, introducing a new method of scanning the table.
There are two modes of lookup that phylib wants: exact, and inexact.
- in exact mode, we return either an exact match or failure
- in inexact mode, we return an exact match if it exists, a match at
the highest speed that is not greater than the requested speed
(ignoring duplex), or failing that, the lowest supported speed, or
failure.
The biggest difference is that we always check whether the entry is
supported before further consideration, so all unsupported entries are
not considered as candidates.
This results in arguably saner behaviour, better matches the comments,
and is probably what users would expect.
This becomes important as ethernet speeds increase, PHYs exist which do
not support the 10Mbit speeds, and half-duplex is likely to become
obsolete - it's already not even an option on 10Gbit and faster links.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE is able to work in any PHY interface mode, there is nothing which
fundamentally restricts it to only a few modes. For example, EEE works
in SGMII mode with the Marvell 88E1512.
Rather than just adding SGMII mode to the list, Florian suggests
removing the list of interface modes entirely:
It actually sounds like we should just kill the check entirely,
it does not appear that any of the interface mode would not
fundamentally be able to support EEE, because the "lowest" mode
we support is MII, and even there it's quite possible to support
EEE.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the EEE advertisment is changed, we should restart autonegotiation
to update the link partner with the new EEE settings. Add this trigger
but only if the advertisment has changed.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently allow userspace to set any EEE advertisments it desires,
whether or not the PHY supports them. For example:
# ethtool --set-eee eth1 advertise 0xffffffff
# ethtool --show-eee eth1
EEE Settings for eth1:
EEE status: disabled
Tx LPI: disabled
Supported EEE link modes: 100baseT/Full
1000baseT/Full
10000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
1000baseKX/Full
10000baseT/Full
10000baseKX4/Full
10000baseKR/Full
Clearly, this is not sane, we should only allow link modes that are
supported to be advertised (as we do elsewhere.) Ensure that we mask
the MDIO_AN_EEE_ADV value with the capabilities retrieved from the
MDIO_PCS_EEE_ABLE register.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PHY is halted on stop, then do not set the state to PHY_UP. This
ensures the phy will be restarted later in phy_start when the machine is
started again.
Fixes: 00db8189d9 ("This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details.")
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Acked-by: Xander Huff <xander.huff@ni.com>
Acked-by: Kyle Roeschley <kyle.roeschley@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch everyone over to using phy_read_mmd() and phy_write_mmd() now
that they are able to handle both Clause 22 indirect addressing and
Clause 45 direct addressing methods to the MMD registers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the phy_(read|write)__mmd() helpers out of line, they will become
our main MMD accessor functions, and so will be a little more complex.
This complexity doesn't belong in an inline function. Also move the
_indirect variants as well to keep like functionality together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan's static checker caught a potential code path in phy_state_machine() where
we were not checking phydev->drv which is in phy_aneg_done().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 25149ef9d2 ("net: phy: Check phydev->drv")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are number of function calls, originating from user-space,
typically through the Ethernet driver that can make us crash by
dereferencing phydev->drv which will be NULL once we unbind the driver
from the PHY.
There are still functional issues that prevent an unbind then rebind to
work, but these will be addressed separately.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
<linux/phy.h> includes <linux/phy_led_triggers.h>, which is not really
needed. Drop the include from <linux/phy.h>, and add it to all users
that didn't include it explicitly.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_error() is called in the PHY state machine workqueue context, and
calls phy_trigger_machine() which does a cancel_delayed_work_sync() of
the workqueue we execute from, causing a deadlock situation.
Augment phy_trigger_machine() machine with a sync boolean indicating
whether we should use cancel_*_sync() or just cancel_*_work().
Fixes: 3c293f4e08 ("net: phy: Trigger state machine on state change and not polling.")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While in RUNNING state, phy_state_machine() checks for link changes by
comparing phydev->link before and after calling phy_read_status().
This works as long as it is guaranteed that phydev->link is never
changed outside the phy_state_machine().
If in some setups this happens, it causes the state machine to miss
a link loss and remain RUNNING despite phydev->link being 0.
This has been observed running a dsa setup with a process continuously
polling the link states over ethtool each second (SNMPD RFC-1213
agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET
causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to
call phy_read_status() and with that modify the link status - and
with that bricking the phy state machine.
This patch adds a fail-safe check while in RUNNING, which causes to
move to CHANGELINK when the link is gone and we are still RUNNING.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the mdix and mdix_ctrl with corresponding ethtool configuration
parameters.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to disable EEE advertisement in the generic PHY
by providing a mask of prohibited modes corresponding to the value found in
the MDIO_AN_EEE_ADV register.
On some platforms, PHY Low power idle seems to be causing issues, even
breaking the link some cases. The patch provides a convenient way for these
platforms to disable EEE advertisement and work around the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function just calls into genphy_restart_aneg() to perform an
autonegotation restart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make phy_aneg_done() available to drivers so that the result of the
auto-negotiation initiated by phy_start_aneg() can be determined.
Remove the local implementation of phy_aneg_done() from the Aeroflex
driver and use the phy library version.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create an option CONFIG_LED_TRIGGER_PHY (default n), which will create a
set of led triggers for each instantiated PHY device. There is one LED
trigger per link-speed, per-phy.
The triggers are registered during phy_attach and unregistered during
phy_detach.
This allows for a user to configure their system to allow a set of LEDs
not controlled by the phy to represent link state changes on the phy.
LEDS controlled by the phy are unaffected.
For example, we have a board where some of the leds in the
RJ45 socket are controlled by the phy, but others are not. Using the
triggers provided by this patch the leds not controlled by the phy can
be configured to show the current speed of the ethernet connection. The
leds controlled by the phy are unaffected.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_supported_speeds provides a means to get a list of all the speeds a
phy device currently supports.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During phy state machine state transitions some set of actions should
occur whenever the link state changes. These actions should be
encapsulated into a single function
This patch adds the phy_adjust_link function, which is called whenever
phydev->adjust_link would have been called before. Actions that should
occur whenever the phy link is adjusted can now be added to the
phy_adjust_link function.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the fixed name "phy_interrupt" is not very informative in
/proc/interrupts when there are a lot of phys, e.g. a device with an
Ethernet switch. So when requesting the interrupt, use the name of the
phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY interrupts are now handled in a threaded interrupt handler,
which can sleep. The work queue is no longer needed, phy_change() can
be called directly. phy_mac_interrupt() still needs to be safe to call
in interrupt context, so keep the work queue, and use a helper to call
phy_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt lines from PHYs maybe connected to I2C bus expanders, or
from switches on MDIO busses. Such interrupts are sourced from devices
which sleep, so use threaded interrupts. Threaded interrupts require
that the interrupt requester also uses the threaded API. Change the
phylib to use the threaded API, which is backwards compatible with
none-threaded IRQs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_start() is used to indicate the PHY is now ready to do its
work. The state is changed, normally to PHY_UP which means that both
the MAC and the PHY are ready.
If the phy driver is using polling, when the next poll happens, the
state machine notices the PHY is now in PHY_UP, and kicks off
auto-negotiation, if needed.
If however, the PHY is using interrupts, there is no polling. The phy
is stuck in PHY_UP until the next interrupt comes along. And there is
no reason for the PHY to interrupt.
Have phy_start() schedule the state machine to run, which both speeds
up the polling use case, and makes the interrupt use case actually
work.
This problems exists whenever there is a state change which will not
cause an interrupt. Trigger the state machine in these cases,
e.g. phy_error().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kyle Roeschley <kyle.roeschley@ni.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts:
commit 33c133cc75 ("phy: IRQ cannot be shared")
On hardware with multiple PHY devices hooked up to the same IRQ line, allow
them to share it.
Sergei Shtylyov says:
"I'm not sure now what was the reason I concluded that the IRQ sharing
was impossible... most probably I thought that the kernel IRQ handling
code exited the loop over the IRQ actions once IRQ_HANDLED was returned
-- which is obviously not so in reality..."
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
If phy was suspended and is starting, current driver always enable
phy's interrupts, if phy works in polling, phy can raise unexpected
interrupt which will not be handled, the interrupt will block system
enter suspend again. So interrupts should only be re-enabled if phy
works in interrupt.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool callbacks {get|set}_link_ksettings are often the same, so
we add two generics functions phy_ethtool_{get|set}_link_ksettings
to avoid writing severals times the same function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-By: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old ethtool api (get_setting and set_setting) has
generic phy functions phy_ethtool_sset and phy_ethtool_gset.
To supprt the new ethtool api (get_link_ksettings and
set_link_ksettings), we add generic phy function
phy_ethtool_ksettings_get and phy_ethtool_ksettings_set.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5ea94e7686 ("phy: add phy_mac_interrupt()") to use with
PHY_IGNORE_INTERRUPT added a cancel_work_sync() into phy_mac_interrupt()
which is allowed to sleep, whereas phy_mac_interrupt() is expected to be
callable from interrupt context.
Now that we have fixed how the PHY state machine treats
PHY_IGNORE_INTERRUPT with respect to state changes, we can just set the
new link state, and queue the PHY state machine for execution so it is
going to read the new link state.
For that to work properly, we need to update phy_change() not to try to
invoke any interrupt callbacks if we have configured the PHY device for
PHY_IGNORE_INTERRUPT, because that PHY device and its driver are not
required to implement those.
Fixes: 5ea94e7686 ("phy: add phy_mac_interrupt() to use with PHY_IGNORE_INTERRUPT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2c7b49212a ("phy: fix the use of PHY_IGNORE_INTERRUPT") changed
a hunk in phy_state_machine() in the PHY_RUNNING case which was not
needed. The change essentially makes the PHY library treat PHY devices
with PHY_IGNORE_INTERRUPT to keep polling for the PHY device, even
though the intent is not to do it.
Fix this by reverting that specific hunk, which makes the PHY state
machine wait for state changes, and stay in the PHY_RUNNING state for as
long as needed.
Fixes: 2c7b49212a ("phy: fix the use of PHY_IGNORE_INTERRUPT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for moving some of the phy_device structure members,
add macros for printing errors and debug information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix scripts/checkpatch.pl's messages like:
CHECK: Comparison to NULL could be written "!phydrv->read_mmd_indirect"
BTW, it doesn't detect the reversed comparisons (which I've fixed as well).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy layer is missing locking for the above two functions - it
has been observed that two threads (userspace and the phy worker
thread) can race, entering the bus ->write or ->read functions
simultaneously.
This causes the FEC driver to initialise a completion while another
thread is waiting on it or while the interrupt is calling complete()
on it, which causes spinlock unlock-without-lock, spinlock lockups,
and completion timeouts.
Fixes: a59a4d192 ("phy: add the EEE support and the way to access to the MMD registers.")
Fixes: 0c1d77dfb ("net: libphy: Add phy specific function to access mmd phy registers")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if phy state is PHY_RUNNING, we always register a CHANGE
when phy works in polling or interrupt ignored, this will make the
adjust_link being called even the phy link did Not changed.
checking the phy link to make sure the link did changed before we
register a CHANGE, if link did not changed, we do nothing.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support manually setting the polarity to mdi or mdix
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the mdix setting from ethtool down to the phy driver, to allow
driver specific implementations of manually setting the polarity.
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update all open-coded tests for all 4 PHY_INTERFACE_MODE_RGMII* values
to use the newly introduced helper: phy_interface_is_rgmii.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an alternative way of fixing:
commit db9683fb41 ("net: phy: Make sure PHY_RESUMING state change
is always processed")
When the PHY state transitions from PHY_HALTED to PHY_RESUMING, there are
two things we need to do:
1). Re-enable interrupts (and power up the physical link, if powered down)
2). Update the PHY state and net-device based on the link status.
There's no strict reason why #1 has to be done from within the main
phy_state_machine() function. There is a risk that other changes to the
PHY (e.g. setting speed/duplex, which calls phy_start_aneg()) could cause
a subsequent state transition before phy_state_machine() has processed
the PHY_RESUMING state change. This would leave the PHY with interrupts
disabled and/or still in the BMCR_PDOWN/low-power mode.
Moving enabling the interrupts and phy_resume() into phy_start() will
guarantee this work always gets done. As the PHY is already in the HALTED
state and interrupts are disabled, it shouldn't conflict with any work
being done in phy_state_machine(). The downside of this change is that if
the PHY_RESUMING state is ever entered from anywhere else, it'll also have
to repeat this work.
Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
If phy_start_aneg() was called while the phydev is in the PHY_RESUMING
state, then its state would immediately transition to PHY_AN (or
PHY_FORCING). This meant the phy_state_machine() never processed the
PHY_RESUMING state change, which meant interrupts weren't enabled for the
PHY. If the PHY used low-power mode (i.e. using BMCR_PDOWN), then the
physical link wouldn't get powered up again.
There seems no point for phy_start_aneg() to make the PHY_RESUMING -->
PHY_AN transition, as the state machine will do this anyway. I'm not sure
about the case where autoneg is disabled, as my patch will change
behaviour so that the PHY goes to PHY_NOLINK instead of PHY_FORCING. An
alternative solution would be to move the phy_config_interrupt() and
phy_resume() work out of the state machine and into phy_start().
The background behind this: we're running linux v3.16.7 and from user-space
we want to enable the eth port (i.e. do a SIOCSIFFLAGS ioctl with the
IFF_UP flag) and immediately afterward set the interface's speed/duplex.
Enabling the interface calls .ndo_open() then phy_start() and the PHY
transitions PHY_HALTED --> PHY_RESUMING. Setting the speed/duplex ends up
calling phy_ethtool_sset(), which calls phy_start_aneg() (meanwhile the
phy_state_machine() hasn't processed the PHY_RESUMING state change yet).
Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can be useful to debug the PHY state machine, add dynamic debug
prints of the old and new PHY devices state under a friendly format.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
