Current handling of CHECKSUM_COMPLETE packets by the UDP stack is
incorrect for any packet that has an incorrect checksum value.
udp4/6_csum_init() will both make a call to
__skb_checksum_validate_complete() to initialize/validate the csum
field when receiving a CHECKSUM_COMPLETE packet. When this packet
fails validation, skb->csum will be overwritten with the pseudoheader
checksum so the packet can be fully validated by software, but the
skb->ip_summed value will be left as CHECKSUM_COMPLETE so that way
the stack can later warn the user about their hardware spewing bad
checksums. Unfortunately, leaving the SKB in this state can cause
problems later on in the checksum calculation.
Since the the packet is still marked as CHECKSUM_COMPLETE,
udp_csum_pull_header() will SUBTRACT the checksum of the UDP header
from skb->csum instead of adding it, leaving us with a garbage value
in that field. Once we try to copy the packet to userspace in the
udp4/6_recvmsg(), we'll make a call to skb_copy_and_csum_datagram_msg()
to checksum the packet data and add it in the garbage skb->csum value
to perform our final validation check.
Since the value we're validating is not the proper checksum, it's possible
that the folded value could come out to 0, causing us not to drop the
packet. Instead, we believe that the packet was checksummed incorrectly
by hardware since skb->ip_summed is still CHECKSUM_COMPLETE, and we attempt
to warn the user with netdev_rx_csum_fault(skb->dev);
Unfortunately, since this is the UDP path, skb->dev has been overwritten
by skb->dev_scratch and is no longer a valid pointer, so we end up
reading invalid memory.
This patch addresses this problem in two ways:
1) Do not use the dev pointer when calling netdev_rx_csum_fault()
from skb_copy_and_csum_datagram_msg(). Since this gets called
from the UDP path where skb->dev has been overwritten, we have
no way of knowing if the pointer is still valid. Also for the
sake of consistency with the other uses of
netdev_rx_csum_fault(), don't attempt to call it if the
packet was checksummed by software.
2) Add better CHECKSUM_COMPLETE handling to udp4/6_csum_init().
If we receive a packet that's CHECKSUM_COMPLETE that fails
verification (i.e. skb->csum_valid == 0), check who performed
the calculation. It's possible that the checksum was done in
software by the network stack earlier (such as Netfilter's
CONNTRACK module), and if that says the checksum is bad,
we can drop the packet immediately instead of waiting until
we try and copy it to userspace. Otherwise, we need to
mark the SKB as CHECKSUM_NONE, since the skb->csum field
no longer contains the full packet checksum after the
call to __skb_checksum_validate_complete().
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Fixes: c84d949057 ("udp: copy skb->truesize in the first cache line")
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an address, route or netconf dump request is sent for AF_UNSPEC, then
rtnl_dump_all is used to do the dump across all address families. If one
of the dumpit functions fails (e.g., invalid attributes in the dump
request) then rtnl_dump_all needs to propagate that error so the user
gets an appropriate response instead of just getting no data.
Fixes: effe679266 ("net: Enable kernel side filtering of route dumps")
Fixes: 5fcd266a9f ("net/ipv4: Add support for dumping addresses for a specific device")
Fixes: 6371a71f3a ("net/ipv6: Add support for dumping addresses for a specific device")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing a route dump across all address families, do not error out
if the table does not exist. This allows a route dump for AF_UNSPEC
with a table id that may only exist for some of the families.
Do return the table does not exist error if dumping routes for a
specific family and the table does not exist.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tgt_net is set based on IFA_TARGET_NETNSID attribute in the dump
request, make sure all error paths call put_net.
Fixes: 6371a71f3a ("net/ipv6: Add support for dumping addresses for a specific device")
Fixes: ed6eff1179 ("net/ipv6: Update inet6_dump_addr for strict data checking")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tgt_net is set based on IFA_TARGET_NETNSID attribute in the dump
request, make sure all error paths call put_net.
Fixes: 5fcd266a9f ("net/ipv4: Add support for dumping addresses for a specific device")
Fixes: c33078e3df ("net/ipv4: Update inet_dump_ifaddr for strict data checking")
Reported-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
readability improvements for the formatted output, some LICENSES updates
including the addition of the ISC license, the removal of the unloved and
unmaintained 00-INDEX files, the deprecated APIs document from Kees, more
MM docs from Mike Rapoport, and the usual pile of typo fixes and
corrections.
-----BEGIN PGP SIGNATURE-----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=C0wt
-----END PGP SIGNATURE-----
Merge tag 'docs-4.20' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"This is a fairly typical cycle for documentation. There's some welcome
readability improvements for the formatted output, some LICENSES
updates including the addition of the ISC license, the removal of the
unloved and unmaintained 00-INDEX files, the deprecated APIs document
from Kees, more MM docs from Mike Rapoport, and the usual pile of typo
fixes and corrections"
* tag 'docs-4.20' of git://git.lwn.net/linux: (41 commits)
docs: Fix typos in histogram.rst
docs: Introduce deprecated APIs list
kernel-doc: fix declaration type determination
doc: fix a typo in adding-syscalls.rst
docs/admin-guide: memory-hotplug: remove table of contents
doc: printk-formats: Remove bogus kobject references for device nodes
Documentation: preempt-locking: Use better example
dm flakey: Document "error_writes" feature
docs/completion.txt: Fix a couple of punctuation nits
LICENSES: Add ISC license text
LICENSES: Add note to CDDL-1.0 license that it should not be used
docs/core-api: memory-hotplug: add some details about locking internals
docs/core-api: rename memory-hotplug-notifier to memory-hotplug
docs: improve readability for people with poorer eyesight
yama: clarify ptrace_scope=2 in Yama documentation
docs/vm: split memory hotplug notifier description to Documentation/core-api
docs: move memory hotplug description into admin-guide/mm
doc: Fix acronym "FEKEK" in ecryptfs
docs: fix some broken documentation references
iommu: Fix passthrough option documentation
...
Pull tty ioctl updates from Al Viro:
"This is the compat_ioctl work related to tty ioctls.
Quite a bit of dead code taken out, all tty-related stuff gone from
fs/compat_ioctl.c. A bunch of compat bugs fixed - some still remain,
but all more or less generic tty-related ioctls should be covered
(remaining issues are in things like driver-private ioctls in a pcmcia
serial card driver not getting properly handled in 32bit processes on
64bit host, etc)"
* 'work.tty-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (53 commits)
kill TIOCSERGSTRUCT
change semantics of ldisc ->compat_ioctl()
kill TIOCSER[SG]WILD
synclink_gt(): fix compat_ioctl()
pty: fix compat ioctls
compat_ioctl - kill keyboard ioctl handling
gigaset: add ->compat_ioctl()
vt_compat_ioctl(): clean up, use compat_ptr() properly
gigaset: don't try to printk userland buffer contents
dgnc: don't bother with (empty) stub for TCXONC
dgnc: leave TIOC[GS]SOFTCAR to ldisc
remove fallback to drivers for TIOCGICOUNT
dgnc: break-related ioctls won't reach ->ioctl()
kill the rest of tty COMPAT_IOCTL() entries
dgnc: TIOCM... won't reach ->ioctl()
isdn_tty: TCSBRK{,P} won't reach ->ioctl()
kill capinc_tty_ioctl()
take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()
synclink: reduce pointless checks in ->ioctl()
complete ->[sg]et_serial() switchover
...
With EDT model, SRTT no longer is inflated by pacing delays.
This means that RTO and some other xmit timers might be setup
incorrectly. This is particularly visible with either :
- Very small enforced pacing rates (SO_MAX_PACING_RATE)
- Reduced rto (from the default 200 ms)
This can lead to TCP flows aborts in the worst case,
or spurious retransmits in other cases.
For example, this session gets far more throughput
than the requested 80kbit :
$ netperf -H 127.0.0.2 -l 100 -- -q 10000
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 127.0.0.2 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
540000 262144 262144 104.00 2.66
With the fix :
$ netperf -H 127.0.0.2 -l 100 -- -q 10000
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 127.0.0.2 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
540000 262144 262144 104.00 0.12
EDT allows for better control of rtx timers, since TCP has
a better idea of the earliest departure time of each skb
in the rtx queue. We only have to eventually add to the
timer the difference of the EDT time with current time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dd979b4df8.
This broke tcp_poll for SMC fallback: An AF_SMC socket establishes an
internal TCP socket for the initial handshake with the remote peer.
Whenever the SMC connection can not be established this TCP socket is
used as a fallback. All socket operations on the SMC socket are then
forwarded to the TCP socket. In case of poll, the file->private_data
pointer references the SMC socket because the TCP socket has no file
assigned. This causes tcp_poll to wait on the wrong socket.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer need to worry about whether or not the entry is hashed in
order to figure out if the contents are valid. We only care whether or
not the refcount is non-zero.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree:
1) rbtree lookup from control plane returns the left-hand side element
of the range when the interval end flag is set on.
2) osf extension is not supported from the input path, reject this from
the control plane, from Fernando Fernandez Mancera.
3) xt_TEE is leaving output interface unset due to a recent incorrect
netns rework, from Taehee Yoo.
4) xt_TEE allows to select an interface which does not belong to this
netnamespace, from Taehee Yoo.
5) Zero private extension area in nft_compat, just like we do in x_tables,
otherwise we leak kernel memory to userspace.
6) Missing .checkentry and .destroy entries in new DNAT extensions breaks
it since we never load nf_conntrack dependencies, from Paolo Abeni.
7) Do not remove flowtable hook from netns exit path, the netdevice handler
already deals with this, also from Taehee Yoo.
8) Only cleanup flowtable entries that reside in this netnamespace, also
from Taehee Yoo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller triggered a use-after-free [1], caused by a combination of
skb_get() in llc_conn_state_process() and usage of sk_eat_skb()
sk_eat_skb() is assuming the skb about to be freed is only used by
the current thread. TCP/DCCP stacks enforce this because current
thread holds the socket lock.
llc_conn_state_process() wants to make sure skb does not disappear,
and holds a reference on the skb it manipulates. But as soon as this
skb is added to socket receive queue, another thread can consume it.
This means that llc must use regular skb_unlink() and kfree_skb()
so that both producer and consumer can safely work on the same skb.
[1]
BUG: KASAN: use-after-free in atomic_read include/asm-generic/atomic-instrumented.h:21 [inline]
BUG: KASAN: use-after-free in refcount_read include/linux/refcount.h:43 [inline]
BUG: KASAN: use-after-free in skb_unref include/linux/skbuff.h:967 [inline]
BUG: KASAN: use-after-free in kfree_skb+0xb7/0x580 net/core/skbuff.c:655
Read of size 4 at addr ffff8801d1f6fba4 by task ksoftirqd/1/18
CPU: 1 PID: 18 Comm: ksoftirqd/1 Not tainted 4.19.0-rc8+ #295
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c4/0x2b6 lib/dump_stack.c:113
print_address_description.cold.8+0x9/0x1ff mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
check_memory_region_inline mm/kasan/kasan.c:260 [inline]
check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267
kasan_check_read+0x11/0x20 mm/kasan/kasan.c:272
atomic_read include/asm-generic/atomic-instrumented.h:21 [inline]
refcount_read include/linux/refcount.h:43 [inline]
skb_unref include/linux/skbuff.h:967 [inline]
kfree_skb+0xb7/0x580 net/core/skbuff.c:655
llc_sap_state_process+0x9b/0x550 net/llc/llc_sap.c:224
llc_sap_rcv+0x156/0x1f0 net/llc/llc_sap.c:297
llc_sap_handler+0x65e/0xf80 net/llc/llc_sap.c:438
llc_rcv+0x79e/0xe20 net/llc/llc_input.c:208
__netif_receive_skb_one_core+0x14d/0x200 net/core/dev.c:4913
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:5023
process_backlog+0x218/0x6f0 net/core/dev.c:5829
napi_poll net/core/dev.c:6249 [inline]
net_rx_action+0x7c5/0x1950 net/core/dev.c:6315
__do_softirq+0x30c/0xb03 kernel/softirq.c:292
run_ksoftirqd+0x94/0x100 kernel/softirq.c:653
smpboot_thread_fn+0x68b/0xa00 kernel/smpboot.c:164
kthread+0x35a/0x420 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:413
Allocated by task 18:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0xc7/0xe0 mm/kasan/kasan.c:553
kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:490
kmem_cache_alloc_node+0x144/0x730 mm/slab.c:3644
__alloc_skb+0x119/0x770 net/core/skbuff.c:193
alloc_skb include/linux/skbuff.h:995 [inline]
llc_alloc_frame+0xbc/0x370 net/llc/llc_sap.c:54
llc_station_ac_send_xid_r net/llc/llc_station.c:52 [inline]
llc_station_rcv+0x1dc/0x1420 net/llc/llc_station.c:111
llc_rcv+0xc32/0xe20 net/llc/llc_input.c:220
__netif_receive_skb_one_core+0x14d/0x200 net/core/dev.c:4913
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:5023
process_backlog+0x218/0x6f0 net/core/dev.c:5829
napi_poll net/core/dev.c:6249 [inline]
net_rx_action+0x7c5/0x1950 net/core/dev.c:6315
__do_softirq+0x30c/0xb03 kernel/softirq.c:292
Freed by task 16383:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/kasan.c:521
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kmem_cache_free+0x83/0x290 mm/slab.c:3756
kfree_skbmem+0x154/0x230 net/core/skbuff.c:582
__kfree_skb+0x1d/0x20 net/core/skbuff.c:642
sk_eat_skb include/net/sock.h:2366 [inline]
llc_ui_recvmsg+0xec2/0x1610 net/llc/af_llc.c:882
sock_recvmsg_nosec net/socket.c:794 [inline]
sock_recvmsg+0xd0/0x110 net/socket.c:801
___sys_recvmsg+0x2b6/0x680 net/socket.c:2278
__sys_recvmmsg+0x303/0xb90 net/socket.c:2390
do_sys_recvmmsg+0x181/0x1a0 net/socket.c:2466
__do_sys_recvmmsg net/socket.c:2484 [inline]
__se_sys_recvmmsg net/socket.c:2480 [inline]
__x64_sys_recvmmsg+0xbe/0x150 net/socket.c:2480
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8801d1f6fac0
which belongs to the cache skbuff_head_cache of size 232
The buggy address is located 228 bytes inside of
232-byte region [ffff8801d1f6fac0, ffff8801d1f6fba8)
The buggy address belongs to the page:
page:ffffea000747dbc0 count:1 mapcount:0 mapping:ffff8801d9be7680 index:0xffff8801d1f6fe80
flags: 0x2fffc0000000100(slab)
raw: 02fffc0000000100 ffffea0007346e88 ffffea000705b108 ffff8801d9be7680
raw: ffff8801d1f6fe80 ffff8801d1f6f0c0 000000010000000b 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801d1f6fa80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff8801d1f6fb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8801d1f6fb80: fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc
^
ffff8801d1f6fc00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8801d1f6fc80: fb fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in the following command:
# tc action add action police rate <r> burst <b> conform-exceed <c1>/<c2>
'goto chain x' is allowed only for c1: setting it for c2 makes the kernel
crash with NULL pointer dereference, since TC core doesn't initialize the
chain handle.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in the following command:
# tc action add action <c1> random <rand_type> <c2> <rand_param>
'goto chain x' is allowed only for c1: setting it for c2 makes the kernel
crash with NULL pointer dereference, since TC core doesn't initialize the
chain handle.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an RTM_GETADDR dump request has ifa_index set in the ifaddrmsg
header, then return only the addresses for that device.
Since inet6_dump_addr is reused for multicast and anycast addresses,
this adds support for device specfic dumps of RTM_GETMULTICAST and
RTM_GETANYCAST as well.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an RTM_GETADDR dump request has ifa_index set in the ifaddrmsg
header, then return only the addresses for that device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_idx is always 0 going into in6_dump_addrs; it is passed as a pointer
to save the last good index into cb. Since cb is already argument to
in6_dump_addrs, just save the value there.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv6 move the logic that walks over the ipv4 address list
for a device into a helper.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have seen the following race scenario:
1) named_distribute() builds a "bulk" message, containing a PUBLISH
item for a certain publication. This is based on the contents of
the binding tables's 'cluster_scope' list.
2) tipc_named_withdraw() removes the same publication from the list,
bulds a WITHDRAW message and distributes it to all cluster nodes.
3) tipc_named_node_up(), which was calling named_distribute(), sends
out the bulk message built under 1)
4) The WITHDRAW message arrives at the just detected node, finds
no corresponding publication, and is dropped.
5) The PUBLISH item arrives at the same node, is added to its binding
table, and remains there forever.
This arrival disordering was earlier taken care of by the backlog queue,
originally added for a different purpose, which was removed in the
commit referred to below, but we now need a different solution.
In this commit, we replace the rcu lock protecting the 'cluster_scope'
list with a regular RW lock which comprises even the sending of the
bulk message. This both guarantees both the list integrity and the
message sending order. We will later add a commit which cleans up
this code further.
Note that this commit needs recently added commit d3092b2efc ("tipc:
fix unsafe rcu locking when accessing publication list") to apply
cleanly.
Fixes: 37922ea4a3 ("tipc: permit overlapping service ranges in name table")
Reported-by: Tuong Lien Tong <tuong.t.lien@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Got below warning with gcc 8.2 compiler.
net/tipc/topsrv.c: In function ‘tipc_topsrv_start’:
net/tipc/topsrv.c:660:2: warning: ‘strncpy’ specified bound depends on the length of the source argument [-Wstringop-overflow=]
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/topsrv.c:660:27: note: length computed here
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~
So change it to correct length and use strscpy.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for performing remote object copies using the 'copy-from'
operation.
[ Add COPY_FROM to get_num_data_items(). ]
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
setup_request_data() adds message data items to both request and reply
messages, but only checks request num_data_items before proceeding with
the loop. This is wrong because if an op doesn't have any request data
items but has a reply data item (e.g. read), a duplicate data item gets
added to the message on every resend attempt.
This went unnoticed for years but now that message data items are
preallocated, it promptly crashes in ceph_msg_data_add(). Amend the
signature to make it clear that setup_request_data() operates on both
request and reply messages. Also, remove data_len assert -- we have
another one in prepare_write_message().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Currently message data items are allocated with ceph_msg_data_create()
in setup_request_data() inside send_request(). send_request() has never
been allowed to fail, so each allocation is followed by a BUG_ON:
data = ceph_msg_data_create(...);
BUG_ON(!data);
It's been this way since support for multiple message data items was
added in commit 6644ed7b7e ("libceph: make message data be a pointer")
in 3.10.
There is no reason to delay the allocation of message data items until
the last possible moment and we certainly don't need a linked list of
them as they are only ever appended to the end and never erased. Make
ceph_msg_new2() take max_data_items and adapt the rest of the code.
Reported-by: Jerry Lee <leisurelysw24@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The current requirement is that ceph_osdc_alloc_messages() should be
called after oid and oloc are known. In preparation for preallocating
message data items, move ceph_osdc_alloc_messages() further down, so
that it is called when OSD op codes are known.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
ceph_osdc_alloc_messages() call will be moved out of
alloc_linger_request() in the next commit, which means that
ceph_osdc_watch() will need to call ceph_osdc_alloc_messages()
twice. Add a helper for that.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Register lingers directly in linger_submit(). This avoids allocating
memory for notify pagelist while holding osdc->lock and simplifies both
callers of linger_submit().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
ceph_msgpool_get() can fall back to ceph_msg_new() when it is asked for
a message whose front portion is larger than pool->front_len. However
the caller always passes 0, effectively disabling that code path. The
allocation goes to the message pool and returns a message with a front
that is smaller than requested, setting us up for a crash.
One example of this is a directory with a large number of snapshots.
If its snap context doesn't fit, we oops in encode_request_partial().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Because send_mds_reconnect() wants to send a message with a pagelist
and pass the ownership to the messenger, ceph_msg_data_add_pagelist()
consumes a ref which is then put in ceph_msg_data_destroy(). This
makes managing pagelists in the OSD client (where they are wrapped in
ceph_osd_data) unnecessarily hard because the handoff only happens in
ceph_osdc_start_request() instead of when the pagelist is passed to
ceph_osd_data_pagelist_init(). I counted several memory leaks on
various error paths.
Fix up ceph_msg_data_add_pagelist() and carry a pagelist ref in
ceph_osd_data.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
struct ceph_pagelist cannot be embedded into anything else because it
has its own refcount. Merge allocation and initialization together.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Implement two new kind of BPF maps, that is, queue and stack
map along with new peek, push and pop operations, from Mauricio.
2) Add support for MSG_PEEK flag when redirecting into an ingress
psock sk_msg queue, and add a new helper bpf_msg_push_data() for
insert data into the message, from John.
3) Allow for BPF programs of type BPF_PROG_TYPE_CGROUP_SKB to use
direct packet access for __skb_buff, from Song.
4) Use more lightweight barriers for walking perf ring buffer for
libbpf and perf tool as well. Also, various fixes and improvements
from verifier side, from Daniel.
5) Add per-symbol visibility for DSO in libbpf and hide by default
global symbols such as netlink related functions, from Andrey.
6) Two improvements to nfp's BPF offload to check vNIC capabilities
in case prog is shared with multiple vNICs and to protect against
mis-initializing atomic counters, from Jakub.
7) Fix for bpftool to use 4 context mode for the nfp disassembler,
also from Jakub.
8) Fix a return value comparison in test_libbpf.sh and add several
bpftool improvements in bash completion, documentation of bpf fs
restrictions and batch mode summary print, from Quentin.
9) Fix a file resource leak in BPF selftest's load_kallsyms()
helper, from Peng.
10) Fix an unused variable warning in map_lookup_and_delete_elem(),
from Alexei.
11) Fix bpf_skb_adjust_room() signature in BPF UAPI helper doc,
from Nicolas.
12) Add missing executables to .gitignore in BPF selftests, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern's dump indexing bug fix in 'net' overlapped the
change of the function signature of inet6_fill_ifaddr() in
'net-next'. Trivially resolved.
Signed-off-by: David S. Miller <davem@davemloft.net>
They are not used anymore and therefore should be removed.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This reverts commit 8e326289e3.
This patch results in unnecessary netlink notification when one
tries to delete a neigh entry already in NUD_FAILED state. Found
this with a buggy app that tries to delete a NUD_FAILED entry
repeatedly. While the notification issue can be fixed with more
checks, adding more complexity here seems unnecessary. Also,
recent tests with other changes in the neighbour code have
shown that the INCOMPLETE and PROBE checks are good enough for
the original issue.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loop wants to skip previously dumped addresses, so loops until
current index >= saved index. If the message fills it wants to save
the index for the next address to dump - ie., the one that did not
fit in the current message.
Currently, it is incrementing the index counter before comparing to the
saved index, and then the saved index is off by 1 - it assumes the
current address is going to fit in the message.
Change the index handling to increment only after a succesful dump.
Fixes: 502a2ffd73 ("ipv6: convert idev_list to list macros")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows user to push data into a msg using sk_msg program types.
The format is as follows,
bpf_msg_push_data(msg, offset, len, flags)
this will insert 'len' bytes at offset 'offset'. For example to
prepend 10 bytes at the front of the message the user can,
bpf_msg_push_data(msg, 0, 10, 0);
This will invalidate data bounds so BPF user will have to then recheck
data bounds after calling this. After this the msg size will have been
updated and the user is free to write into the added bytes. We allow
any offset/len as long as it is within the (data, data_end) range.
However, a copy will be required if the ring is full and its possible
for the helper to fail with ENOMEM or EINVAL errors which need to be
handled by the BPF program.
This can be used similar to XDP metadata to pass data between sk_msg
layer and lower layers.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-10-20
Here's one more bluetooth-next pull request for the 4.20 kernel.
- Added new USB ID for QCA_ROME controller
- Added debug trace support from QCA wcn3990 controllers
- Updated L2CAP to conform to latest Errata Service Release
- Fix binding to non-removable BCM43430 devices
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree:
1) Use lockdep_is_held() in ipset_dereference_protected(), from Lance Roy.
2) Remove unused variable in cttimeout, from YueHaibing.
3) Add ttl option for nft_osf, from Fernando Fernandez Mancera.
4) Use xfrm family to deal with IPv6-in-IPv4 packets from nft_xfrm,
from Florian Westphal.
5) Simplify xt_osf_match_packet().
6) Missing ct helper alias definition in snmp_trap helper, from Taehee Yoo.
7) Remove unnecessary parameter in nf_flow_table_cleanup(), from Taehee Yoo.
8) Remove unused variable definitions in nft_{dup,fwd}, from Weongyo Jeong.
9) Remove empty net/netfilter/nfnetlink_log.h file, from Taehee Yoo.
10) Revert xt_quota updates remain option due to problems in the listing
path for 32-bit arches, from Maze.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We've been getting checksum errors involving small UDP packets, usually
59B packets with 1 extra non-zero padding byte. netdev_rx_csum_fault()
has been complaining that HW is providing bad checksums. Turns out the
problem is in pskb_trim_rcsum_slow(), introduced in commit 88078d98d1
("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends").
The source of the problem is that when the bytes we are trimming start
at an odd address, as in the case of the 1 padding byte above,
skb_checksum() returns a byte-swapped value. We cannot just combine this
with skb->csum using csum_sub(). We need to use csum_block_sub() here
that takes into account the parity of the start address and handles the
swapping.
Matches existing code in __skb_postpull_rcsum() and esp_remove_trailer().
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Signed-off-by: Dimitris Michailidis <dmichail@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a problem introduced by:
commit 2cde6acd49 ("netpoll: Fix __netpoll_rcu_free so that it can hold the rtnl lock")
When using netconsole on a bond, __netpoll_cleanup can asynchronously
recurse multiple times, each __netpoll_free_async call can result in
more __netpoll_free_async's. This means there is now a race between
cleanup_work queues on multiple netpoll_info's on multiple devices and
the configuration of a new netpoll. For example if a netconsole is set
to enable 0, reconfigured, and enable 1 immediately, this netconsole
will likely not work.
Given the reason for __netpoll_free_async is it can be called when rtnl
is not locked, if it is locked, we should be able to execute
synchronously. It appears to be locked everywhere it's called from.
Generalize the design pattern from the teaming driver for current
callers of __netpoll_free_async.
CC: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before using the psock returned by sk_psock_get() when adding it to a
sockmap we need to ensure it is actually a sockmap based psock.
Previously we were only checking this after incrementing the reference
counter which was an error. This resulted in a slab-out-of-bounds
error when the psock was not actually a sockmap type.
This moves the check up so the reference counter is only used
if it is a sockmap psock.
Eric reported the following KASAN BUG,
BUG: KASAN: slab-out-of-bounds in atomic_read include/asm-generic/atomic-instrumented.h:21 [inline]
BUG: KASAN: slab-out-of-bounds in refcount_inc_not_zero_checked+0x97/0x2f0 lib/refcount.c:120
Read of size 4 at addr ffff88019548be58 by task syz-executor4/22387
CPU: 1 PID: 22387 Comm: syz-executor4 Not tainted 4.19.0-rc7+ #264
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c4/0x2b4 lib/dump_stack.c:113
print_address_description.cold.8+0x9/0x1ff mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
check_memory_region_inline mm/kasan/kasan.c:260 [inline]
check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267
kasan_check_read+0x11/0x20 mm/kasan/kasan.c:272
atomic_read include/asm-generic/atomic-instrumented.h:21 [inline]
refcount_inc_not_zero_checked+0x97/0x2f0 lib/refcount.c:120
sk_psock_get include/linux/skmsg.h:379 [inline]
sock_map_link.isra.6+0x41f/0xe30 net/core/sock_map.c:178
sock_hash_update_common+0x19b/0x11e0 net/core/sock_map.c:669
sock_hash_update_elem+0x306/0x470 net/core/sock_map.c:738
map_update_elem+0x819/0xdf0 kernel/bpf/syscall.c:818
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tests are added to make sure CGROUP_SKB cannot access:
tc_classid, data_meta, flow_keys
and can read and write:
mark, prority, and cb[0-4]
and can read other fields.
To make selftest with skb->sk work, a dummy sk is added in
bpf_prog_test_run_skb().
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
BPF programs of BPF_PROG_TYPE_CGROUP_SKB need to access headers in the
skb. This patch enables direct access of skb for these programs.
Two helper functions bpf_compute_and_save_data_end() and
bpf_restore_data_end() are introduced. There are used in
__cgroup_bpf_run_filter_skb(), to compute proper data_end for the
BPF program, and restore original data afterwards.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Queue/stack maps implement a FIFO/LIFO data storage for ebpf programs.
These maps support peek, pop and push operations that are exposed to eBPF
programs through the new bpf_map[peek/pop/push] helpers. Those operations
are exposed to userspace applications through the already existing
syscalls in the following way:
BPF_MAP_LOOKUP_ELEM -> peek
BPF_MAP_LOOKUP_AND_DELETE_ELEM -> pop
BPF_MAP_UPDATE_ELEM -> push
Queue/stack maps are implemented using a buffer, tail and head indexes,
hence BPF_F_NO_PREALLOC is not supported.
As opposite to other maps, queue and stack do not use RCU for protecting
maps values, the bpf_map[peek/pop] have a ARG_PTR_TO_UNINIT_MAP_VALUE
argument that is a pointer to a memory zone where to save the value of a
map. Basically the same as ARG_PTR_TO_UNINIT_MEM, but the size has not
be passed as an extra argument.
Our main motivation for implementing queue/stack maps was to keep track
of a pool of elements, like network ports in a SNAT, however we forsee
other use cases, like for exampling saving last N kernel events in a map
and then analysing from userspace.
Signed-off-by: Mauricio Vasquez B <mauricio.vasquez@polito.it>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6fe9487892.
It is causing more serious regressions than the RCU warning
it is fixing.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e9837e55b0.
When talking to Maze and Chenbo, we agreed to keep this back by now
due to problems in the ruleset listing path with 32-bit arches.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nft_dup_netdev_ingress_ops and nft_fwd_netdev_ingress_ops variables are
no longer used at the code.
Signed-off-by: Weongyo Jeong <weongyo.linux@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When interface is down, offload cleanup function(nf_flow_table_do_cleanup)
is called and that checks whether interface index of offload and
index of link down interface is same. but only interface index checking
is not enough because flowtable is not pernet list.
So that, if other netns's interface that has index is same with offload
is down, that offload will be removed.
This patch adds netns checking code to the offload cleanup routine.
Fixes: 59c466dd68 ("netfilter: nf_flow_table: add a new flow state for tearing down offloading")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
parameter net of nf_flow_table_cleanup() is not used.
So that it can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 058214a4d1 ("ip6_tun: Add infrastructure for doing
encapsulation") added the ip6_tnl_encap() call in ip6_tnl_xmit(), before
the call to ipv6_push_frag_opts() to append the IPv6 Tunnel Encapsulation
Limit option (option 4, RFC 2473, par. 5.1) to the outer IPv6 header.
As long as the option didn't actually end up in generated packets, this
wasn't an issue. Then commit 89a23c8b52 ("ip6_tunnel: Fix missing tunnel
encapsulation limit option") fixed sending of this option, and the
resulting layout, e.g. for FoU, is:
.-------------------.------------.----------.-------------------.----- - -
| Outer IPv6 Header | UDP header | Option 4 | Inner IPv6 Header | Payload
'-------------------'------------'----------'-------------------'----- - -
Needless to say, FoU and GUE (at least) won't work over IPv6. The option
is appended by default, and I couldn't find a way to disable it with the
current iproute2.
Turn this into a more reasonable:
.-------------------.----------.------------.-------------------.----- - -
| Outer IPv6 Header | Option 4 | UDP header | Inner IPv6 Header | Payload
'-------------------'----------'------------'-------------------'----- - -
With this, and with 84dad55951 ("udp6: fix encap return code for
resubmitting"), FoU and GUE work again over IPv6.
Fixes: 058214a4d1 ("ip6_tun: Add infrastructure for doing encapsulation")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported the following warning triggered while running CRIU tests:
tcp_clean_rtx_queue()
...
last_ackt = tcp_skb_timestamp_us(skb);
WARN_ON_ONCE(last_ackt == 0);
This is caused by 5f6188a800 ("tcp: do not change tcp_wstamp_ns
in tcp_mstamp_refresh"), as we end up having skbs in retransmit queue
with a zero skb->skb_mstamp_ns field.
We could fix this bug in different ways, like making sure
tp->tcp_wstamp_ns is not zero at socket creation, but as Neal pointed
out, we also do not want that pacing status of a repaired socket
could push tp->tcp_wstamp_ns far ahead in the future.
So we prefer changing tcp_write_xmit() to not call tcp_update_skb_after_send()
and instead do what is requested by TCP_REPAIR logic.
Fixes: 5f6188a800 ("tcp: do not change tcp_wstamp_ns in tcp_mstamp_refresh")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We initialize a struct tipc_event allocated on the kernel stack to
zero to avert info leak to user space.
Reported-by: syzbot+057458894bc8cada4dee@syzkaller.appspotmail.com
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ethtool_ioctl(), the ioctl command 'ethcmd' is checked through a switch
statement to see whether it is necessary to pre-process the ethtool
structure, because, as mentioned in the comment, the structure
ethtool_rxnfc is defined with padding. If yes, a user-space buffer 'rxnfc'
is allocated through compat_alloc_user_space(). One thing to note here is
that, if 'ethcmd' is ETHTOOL_GRXCLSRLALL, the size of the buffer 'rxnfc' is
partially determined by 'rule_cnt', which is actually acquired from the
user-space buffer 'compat_rxnfc', i.e., 'compat_rxnfc->rule_cnt', through
get_user(). After 'rxnfc' is allocated, the data in the original user-space
buffer 'compat_rxnfc' is then copied to 'rxnfc' through copy_in_user(),
including the 'rule_cnt' field. However, after this copy, no check is
re-enforced on 'rxnfc->rule_cnt'. So it is possible that a malicious user
race to change the value in the 'compat_rxnfc->rule_cnt' between these two
copies. Through this way, the attacker can bypass the previous check on
'rule_cnt' and inject malicious data. This can cause undefined behavior of
the kernel and introduce potential security risk.
This patch avoids the above issue via copying the value acquired by
get_user() to 'rxnfc->rule_cn', if 'ethcmd' is ETHTOOL_GRXCLSRLALL.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping classes by parent, kernel would return classes twice:
| # tc qdisc add dev lo root prio
| # tc class show dev lo
| class prio 8001:1 parent 8001:
| class prio 8001:2 parent 8001:
| class prio 8001:3 parent 8001:
| # tc class show dev lo parent 8001:
| class prio 8001:1 parent 8001:
| class prio 8001:2 parent 8001:
| class prio 8001:3 parent 8001:
| class prio 8001:1 parent 8001:
| class prio 8001:2 parent 8001:
| class prio 8001:3 parent 8001:
This comes from qdisc_match_from_root() potentially returning the root
qdisc itself if its handle matched. Though in that case, root's classes
were already dumped a few lines above.
Fixes: cb395b2010 ("net: sched: optimize class dumps")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable bugfixes:
- Reset credit grant properly after a disconnect
Other bugfixes and cleanups:
- xprt_release_rqst_cong is called outside of transport_lock
- Create more MRs at a time and toss out old ones during recovery
- Various improvements to the RDMA connection and disconnection code:
- Improve naming of trace events, functions, and variables
- Add documenting comments
- Fix metrics and stats reporting
- Fix a tracepoint sparse warning
-----BEGIN PGP SIGNATURE-----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=SxSD
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-for-4.20-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
NFS RDMA client updates for Linux 4.20
Stable bugfixes:
- Reset credit grant properly after a disconnect
Other bugfixes and cleanups:
- xprt_release_rqst_cong is called outside of transport_lock
- Create more MRs at a time and toss out old ones during recovery
- Various improvements to the RDMA connection and disconnection code:
- Improve naming of trace events, functions, and variables
- Add documenting comments
- Fix metrics and stats reporting
- Fix a tracepoint sparse warning
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Commits ffb6ca33b0 and e08ea3a96f prevent setting xprt_min_resvport
greater than xprt_max_resvport, but may also break simple code that sets
one parameter then the other, if the new range does not overlap the old.
Also it looks racy to me, unless there's some serialization I'm not
seeing. Granted it would probably require malicious privileged processes
(unless there's a chance these might eventually be settable in unprivileged
containers), but still it seems better not to let userspace panic the
kernel.
Simpler seems to be to allow setting the parameters to whatever you want
but interpret xprt_min_resvport > xprt_max_resvport as the empty range.
Fixes: ffb6ca33b0 "sunrpc: Prevent resvport min/max inversion..."
Fixes: e08ea3a96f "sunrpc: Prevent rexvport min/max inversion..."
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
sk->sk_wmem_queued is used to count the size of chunks in out queue
while sk->sk_wmem_alloc is for counting the size of chunks has been
sent. sctp is increasing both of them before enqueuing the chunks,
and using sk->sk_wmem_alloc to check for writable space.
However, sk_wmem_alloc is also increased by 1 for the skb allocked
for sending in sctp_packet_transmit() but it will not wake up the
waiters when sk_wmem_alloc is decreased in this skb's destructor.
If msg size is equal to sk_sndbuf and sendmsg is waiting for sndbuf,
the check 'msg_len <= sctp_wspace(asoc)' in sctp_wait_for_sndbuf()
will keep waiting if there's a skb allocked in sctp_packet_transmit,
and later even if this skb got freed, the waiting thread will never
get waked up.
This issue has been there since very beginning, so we change to use
sk->sk_wmem_queued to check for writable space as sk_wmem_queued is
not increased for the skb allocked for sending, also as TCP does.
SOCK_SNDBUF_LOCK check is also removed here as it's for tx buf auto
tuning which I will add in another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now it's confusing that asoc sndbuf_used is doing memory accounting with
SCTP_DATA_SNDSIZE(chunk) + sizeof(sk_buff) + sizeof(sctp_chunk) while sk
sk_wmem_alloc is doing that with skb->truesize + sizeof(sctp_chunk).
It also causes sctp_prsctp_prune to count with a wrong freed memory when
sndbuf_policy is not set.
To make this right and also keep consistent between asoc sndbuf_used, sk
sk_wmem_alloc and sk_wmem_queued, use skb->truesize + sizeof(sctp_chunk)
for them.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-10-18
1) Remove an unnecessary dev->tstats check in xfrmi_get_stats64.
From Li RongQing.
2) We currently do a sizeof(element) instead of a sizeof(array)
check when initializing the ovec array of the secpath.
Currently this array can have only one element, so code is
OK but error-prone. Change this to do a sizeof(array)
check so that we can add more elements in future.
From Li RongQing.
3) Improve xfrm IPv6 address hashing by using the complete IPv6
addresses for a hash. From Michal Kubecek.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-10-18
1) Free the xfrm interface gro_cells when deleting the
interface, otherwise we leak it. From Li RongQing.
2) net/core/flow.c does not exist anymore, so remove it
from the MAINTAINERS file.
3) Fix a slab-out-of-bounds in _decode_session6.
From Alexei Starovoitov.
4) Fix RCU protection when policies inserted into
thei bydst lists. From Florian Westphal.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the skb space ends in an unresolved entry while dumping we'll miss
some unresolved entries. The reason is due to zeroing the entry counter
between dumping resolved and unresolved mfc entries. We should just
keep counting until the whole table is dumped and zero when we move to
the next as we have a separate table counter.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 8fb472c09b ("ipmr: improve hash scalability")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit eb63f2964d ("udp6: add missing checks on edumux packet
processing") used the same return code convention of the ipv4 counterpart,
but ipv6 uses the opposite one: positive values means resubmit.
This change addresses the issue, using positive return value for
resubmitting. Also update the related comment, which was broken, too.
Fixes: eb63f2964d ("udp6: add missing checks on edumux packet processing")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Centralize the code that sets gains used for computing cwnd and pacing
rate. This simplifies the code and makes it easier to change the state
machine or (in the future) dynamically change the gain values and
ensure that the correct gain values are always used.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust TCP BBR for the new departure time pacing model in the recent
commit ab408b6dc7 ("tcp: switch tcp and sch_fq to new earliest
departure time model").
With TSQ and pacing at lower layers, there are often several skbs
queued in the pacing layer, and thus there is less data "in the
network" than "in flight".
With departure time pacing at lower layers (e.g. fq or potential
future NICs), the data in the pacing layer now has a pre-scheduled
("baked-in") departure time that cannot be changed, even if the
congestion control algorithm decides to use a new pacing rate.
This means that there can be a non-trivial lag between when BBR makes
a pacing rate change and when the inter-skb pacing delays
change. After a pacing rate change, the number of packets in the
network can gradually evolve to be higher or lower, depending on
whether the sending rate is higher or lower than the delivery
rate. Thus ignoring this lag can cause significant overshoot, with the
flow ending up with too many or too few packets in the network.
This commit changes BBR to adapt its pacing rate based on the amount
of data in the network that it estimates has already been "baked in"
by previous departure time decisions. We estimate the number of our
packets that will be in the network at the earliest departure time
(EDT) for the next skb scheduled as:
in_network_at_edt = inflight_at_edt - (EDT - now) * bw
If we're increasing the amount of data in the network ("in_network"),
then we want to know if the transmit of the EDT skb will push
in_network above the target, so our answer includes
bbr_tso_segs_goal() from the skb departing at EDT. If we're decreasing
in_network, then we want to know if in_network will sink too low just
before the EDT transmit, so our answer does not include the segments
from the skb departing at EDT.
Why do we treat pacing_gain > 1.0 case and pacing_gain < 1.0 case
differently? The in_network curve is a step function: in_network goes
up on transmits, and down on ACKs. To accurately predict when
in_network will go beyond our target value, this will happen on
different events, depending on whether we're concerned about
in_network potentially going too high or too low:
o if pushing in_network up (pacing_gain > 1.0),
then in_network goes above target upon a transmit event
o if pushing in_network down (pacing_gain < 1.0),
then in_network goes below target upon an ACK event
This commit changes the BBR state machine to use this estimated
"packets in network" value to make its decisions.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds OEM Broadcom commands and response handling. It also
defines OEM Get MAC Address handler to get and configure the device.
ncsi_oem_gma_handler_bcm: This handler send NCSI broadcom command for
getting mac address.
ncsi_rsp_handler_oem_bcm: This handles response received for all
broadcom OEM commands.
ncsi_rsp_handler_oem_bcm_gma: This handles get mac address response and
set it to device.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sctp_wait_for_connect is called to wait for connect ready
for sp->strm_interleave in sctp_sendmsg_to_asoc, a panic could
be triggered if cpu is scheduled out and the new asoc is freed
elsewhere, as it will return err and later the asoc gets freed
again in sctp_sendmsg.
[ 285.840764] list_del corruption, ffff9f0f7b284078->next is LIST_POISON1 (dead000000000100)
[ 285.843590] WARNING: CPU: 1 PID: 8861 at lib/list_debug.c:47 __list_del_entry_valid+0x50/0xa0
[ 285.846193] Kernel panic - not syncing: panic_on_warn set ...
[ 285.846193]
[ 285.848206] CPU: 1 PID: 8861 Comm: sctp_ndata Kdump: loaded Not tainted 4.19.0-rc7.label #584
[ 285.850559] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 285.852164] Call Trace:
...
[ 285.872210] ? __list_del_entry_valid+0x50/0xa0
[ 285.872894] sctp_association_free+0x42/0x2d0 [sctp]
[ 285.873612] sctp_sendmsg+0x5a4/0x6b0 [sctp]
[ 285.874236] sock_sendmsg+0x30/0x40
[ 285.874741] ___sys_sendmsg+0x27a/0x290
[ 285.875304] ? __switch_to_asm+0x34/0x70
[ 285.875872] ? __switch_to_asm+0x40/0x70
[ 285.876438] ? ptep_set_access_flags+0x2a/0x30
[ 285.877083] ? do_wp_page+0x151/0x540
[ 285.877614] __sys_sendmsg+0x58/0xa0
[ 285.878138] do_syscall_64+0x55/0x180
[ 285.878669] entry_SYSCALL_64_after_hwframe+0x44/0xa9
This is a similar issue with the one fixed in Commit ca3af4dd28
("sctp: do not free asoc when it is already dead in sctp_sendmsg").
But this one can't be fixed by returning -ESRCH for the dead asoc
in sctp_wait_for_connect, as it will break sctp_connect's return
value to users.
This patch is to simply set err to -ESRCH before it returns to
sctp_sendmsg when any err is returned by sctp_wait_for_connect
for sp->strm_interleave, so that no asoc would be freed due to
this.
When users see this error, they will know the packet hasn't been
sent. And it also makes sense to not free asoc because waiting
connect fails, like the second call for sctp_wait_for_connect in
sctp_sendmsg_to_asoc.
Fixes: 668c9beb90 ("sctp: implement assign_number for sctp_stream_interleave")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported an use-after-free involving sctp_id2asoc. Dmitry Vyukov
helped to root cause it and it is because of reading the asoc after it
was freed:
CPU 1 CPU 2
(working on socket 1) (working on socket 2)
sctp_association_destroy
sctp_id2asoc
spin lock
grab the asoc from idr
spin unlock
spin lock
remove asoc from idr
spin unlock
free(asoc)
if asoc->base.sk != sk ... [*]
This can only be hit if trying to fetch asocs from different sockets. As
we have a single IDR for all asocs, in all SCTP sockets, their id is
unique on the system. An application can try to send stuff on an id
that matches on another socket, and the if in [*] will protect from such
usage. But it didn't consider that as that asoc may belong to another
socket, it may be freed in parallel (read: under another socket lock).
We fix it by moving the checks in [*] into the protected region. This
fixes it because the asoc cannot be freed while the lock is held.
Reported-by: syzbot+c7dd55d7aec49d48e49a@syzkaller.appspotmail.com
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pid_task() dereferences rcu protected tasks array.
But there is no rcu_read_lock() in shutdown_umh() routine so that
rcu_read_lock() is needed.
get_pid_task() is wrapper function of pid_task. it holds rcu_read_lock()
then calls pid_task(). if task isn't NULL, it increases reference count
of task.
test commands:
%modprobe bpfilter
%modprobe -rv bpfilter
splat looks like:
[15102.030932] =============================
[15102.030957] WARNING: suspicious RCU usage
[15102.030985] 4.19.0-rc7+ #21 Not tainted
[15102.031010] -----------------------------
[15102.031038] kernel/pid.c:330 suspicious rcu_dereference_check() usage!
[15102.031063]
other info that might help us debug this:
[15102.031332]
rcu_scheduler_active = 2, debug_locks = 1
[15102.031363] 1 lock held by modprobe/1570:
[15102.031389] #0: 00000000580ef2b0 (bpfilter_lock){+.+.}, at: stop_umh+0x13/0x52 [bpfilter]
[15102.031552]
stack backtrace:
[15102.031583] CPU: 1 PID: 1570 Comm: modprobe Not tainted 4.19.0-rc7+ #21
[15102.031607] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/08/2015
[15102.031628] Call Trace:
[15102.031676] dump_stack+0xc9/0x16b
[15102.031723] ? show_regs_print_info+0x5/0x5
[15102.031801] ? lockdep_rcu_suspicious+0x117/0x160
[15102.031855] pid_task+0x134/0x160
[15102.031900] ? find_vpid+0xf0/0xf0
[15102.032017] shutdown_umh.constprop.1+0x1e/0x53 [bpfilter]
[15102.032055] stop_umh+0x46/0x52 [bpfilter]
[15102.032092] __x64_sys_delete_module+0x47e/0x570
[ ... ]
Fixes: d2ba09c17a ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the "'hash' may be used uninitialized in this function"
net/unix/af_unix.c:1041:20: warning: 'hash' may be used uninitialized in this function [-Wmaybe-uninitialized]
addr->hash = hash ^ sk->sk_type;
Signed-off-by: Kyeongdon Kim <kyeongdon.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, an FDB entry only ceases being offloaded when it is deleted.
This changes with VxLAN encapsulation.
Devices capable of performing VxLAN encapsulation usually have only one
FDB table, unlike the software data path which has two - one in the
bridge driver and another in the VxLAN driver.
Therefore, bridge FDB entries pointing to a VxLAN device are only
offloaded if there is a corresponding entry in the VxLAN FDB.
Allow clearing the offload indication in case the corresponding entry
was deleted from the VxLAN FDB.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the MSG_PEEK flag when doing redirect to ingress
and receiving on the sk_msg psock queue. Previously the flag was
being ignored which could confuse applications if they expected the
flag to work as normal.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When converting sockmap to new skmsg generic data structures we missed
that the recvmsg handler did not correctly use sg.size and instead was
using individual elements length. The result is if a sock is closed
with outstanding data we omit the call to sk_mem_uncharge() and can
get the warning below.
[ 66.728282] WARNING: CPU: 6 PID: 5783 at net/core/stream.c:206 sk_stream_kill_queues+0x1fa/0x210
To fix this correct the redirect handler to xfer the size along with
the scatterlist and also decrement the size from the recvmsg handler.
Now when a sock is closed the remaining 'size' will be decremented
with sk_mem_uncharge().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Eric reported that syzkaller triggered a splat in tcp_cleanup_ulp()
where assertion sock_owned_by_me() failed. This happened through
inet_csk_prepare_forced_close() first releasing the socket lock,
then calling into tcp_done(newsk) which is called after the
inet_csk_prepare_forced_close() and therefore without the socket
lock held. The sock_owned_by_me() assertion can generally be
removed as the only place where tcp_cleanup_ulp() is called from
now is out of inet_csk_destroy_sock() -> sk->sk_prot->destroy()
where socket is in dead state and unreachable. Therefore, add a
comment why the check is not needed instead.
Fixes: 8b9088f806 ("tcp, ulp: enforce sock_owned_by_me upon ulp init and cleanup")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 2eb0f624b7 ("netfilter: add NAT support for shifted
portmap ranges") did not set the checkentry/destroy callbacks for
the newly added DNAT target. As a result, rulesets using only
such nat targets are not effective, as the relevant conntrack hooks
are not enabled.
The above affect also nft_compat rulesets.
Fix the issue adding the missing initializers.
Fixes: 2eb0f624b7 ("netfilter: add NAT support for shifted portmap ranges")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
According to rfc7496 section 4.3 or 4.4:
sprstat_policy: This parameter indicates for which PR-SCTP policy
the user wants the information. It is an error to use
SCTP_PR_SCTP_NONE in sprstat_policy. If SCTP_PR_SCTP_ALL is used,
the counters provided are aggregated over all supported policies.
We change to dump pr_assoc and pr_stream all status by SCTP_PR_SCTP_ALL
instead, and return error for SCTP_PR_SCTP_NONE, as it also said "It is
an error to use SCTP_PR_SCTP_NONE in sprstat_policy. "
Fixes: 826d253d57 ("sctp: add SCTP_PR_ASSOC_STATUS on sctp sockopt")
Fixes: d229d48d18 ("sctp: add SCTP_PR_STREAM_STATUS sockopt for prsctp")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to upload helper module automatically, helper alias name
is needed. so that MODULE_ALIAS_NFCT_HELPER() should be added.
And unlike other nat helper modules, the nf_nat_snmp_basic can be
used independently.
helper name is "snmp_trap" so that alias name will be
"nfct-helper-snmp_trap" by MODULE_ALIAS_NFCT_HELPER(snmp_trap)
test command:
%iptables -t raw -I PREROUTING -p udp -j CT --helper snmp_trap
%lsmod | grep nf_nat_snmp_basic
We can see nf_nat_snmp_basic module is uploaded automatically.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Eyal says:
doesn't the use of nft_pf(pkt) in this context limit the matching of
encapsulated packets to the same family?
IIUC when an e.g. IPv6-in-IPv4 packet is matched, the nft_pf(pkt) will
be the decapsulated packet family - IPv6 - whereas the state may be
IPv4. So this check would not allow matching the 'underlay' address in
such cases.
I know this was a limitation in xt_policy. but is this intentional in
this matcher? or is it possible to use state->props.family when
validating the match instead of nft_pf(pkt)?
Userspace already tells us which address family it expects to match, so
we can just use the real state family rather than the hook family.
so change it as suggested above.
Reported-by: Eyal Birger <eyal.birger@gmail.com>
Suggested-by: Eyal Birger <eyal.birger@gmail.com>
Fixes: 6c47260250 ("netfilter: nf_tables: add xfrm expression")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add ttl option support to the nftables "osf" expression.
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes gcc '-Wunused-but-set-variable' warning:
net/netfilter/nfnetlink_cttimeout.c: In function 'cttimeout_default_set':
net/netfilter/nfnetlink_cttimeout.c:353:8: warning:
variable 'l3num' set but not used [-Wunused-but-set-variable]
It not used any more after
commit dd2934a957 ("netfilter: conntrack: remove l3->l4 mapping information")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Florian Westphal <fw@strlen.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <netfilter-devel@vger.kernel.org>
Cc: <coreteam@netfilter.org>
Cc: <netdev@vger.kernel.org>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Unlike IPv6, IPv4 does not have routes marked with RTF_PREFIX_RT. If the
flag is set in the dump request, just return.
In the process of this change, move the CLONE check to use the new
filter flags.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, IPv6 fib no longer contains cloned routes. If a user
requests a route dump for only cloned entries, no sense walking the FIB
and returning everything.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the dump request parsing in MPLS for the non-INET case to
enable kernel side filtering. If INET is disabled the only filters
that make sense for MPLS are protocol and nexthop device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update parsing of route dump request to enable kernel side filtering.
Allow filtering results by protocol (e.g., which routing daemon installed
the route), route type (e.g., unicast), table id and nexthop device. These
amount to the low hanging fruit, yet a huge improvement, for dumping
routes.
ip_valid_fib_dump_req is called with RTNL held, so __dev_get_by_index can
be used to look up the device index without taking a reference. From
there filter->dev is only used during dump loops with the lock still held.
Set NLM_F_DUMP_FILTERED in the answer_flags so the user knows the results
have been filtered should no entries be returned.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement kernel side filtering of routes by egress device index and
table id. If the table id is given in the filter, lookup table and
call mr_table_dump directly for it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move per-table loops from mr_rtm_dumproute to mr_table_dump and export
mr_table_dump for dumps by specific table id.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement kernel side filtering of routes by egress device index and
protocol. MPLS uses only a single table and route type.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement kernel side filtering of routes by table id, egress device
index, protocol, and route type. If the table id is given in the filter,
lookup the table and call fib6_dump_table directly for it.
Move the existing route flags check for prefix only routes to the new
filter.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement kernel side filtering of routes by table id, egress device index,
protocol and route type. If the table id is given in the filter, lookup the
table and call fib_table_dump directly for it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
