On one of my machines the cancellation of TPM commands does not work.
The reason is that by writing into sysfs 'cancel' the tpm_tis_ready
call causes the status flag TPM_STS_VALID to be set in the statusregister.
However, the TIS driver seems to wait for TPM_STS_COMMAND_READY.
Once a 2nd time sysfs 'cancel' is written to, the TPM_STS_COMMAND_READY flag
also gets set, resulting in TPM_STS_VALID|TPM_STS_COMMAND_READY to be
read from the status register.
This patch now converts req_canceled into a function to enable more complex
comparisons against possible cancellation status codes.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
We've been testing an alternative TPM for our embedded products and
found random kernel boot failures due to time outs after the continue
self test command.
This was happening randomly, and has been *very* hard to track down, but
it
looks like with this chip there is some kind of race with the
tpm_tis_status()
check of TPM_STS_COMMAND_READY. If things get there 'too fast' then
it sees the chip is ready, or tpm_tis_ready() works. Otherwise it takes
somewhere over 400ms before the chip will return TPM_STS_COMMAND_READY.
Adding some delay after tpm_continue_selftest() makes things reliably
hit the failure path, otherwise it is a crapshot.
The spec says it should be returning TPM_WARN_DOING_SELFTEST, not
holding
off on ready..
Boot log during this event looks like this:
tpm_tis 70030000.tpm_tis: 1.2 TPM (device-id 0x3204, rev-id 64)
tpm_tis 70030000.tpm_tis: Issuing TPM_STARTUP
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
The other TPM vendor we use doesn't show this wonky behaviour:
tpm_tis 70030000.tpm_tis: 1.2 TPM (device-id 0xFE, rev-id 70)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
When no i2c bus exists, user-space can cause an oops by triggering a
device probe through a message sent to an i2c "new_device" sysfs entry.
Adding a check for a NULL i2c client structure in the probe function
closes the hole.
This patch also fixes accessing the NULL client struct in the print
function call reporting the error.
Reported-by: Peter Hüwe <PeterHuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch converts the suspend and resume functions for
tpm_i2c_stm_st33 to the new dev_pm_ops.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
* STMicroelectronics version 1.2.0, Copyright (C) 2010
* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
* This is free software, and you are welcome to redistribute it
* under certain conditions.
This is the driver for TPM chip from ST Microelectronics.
If you have a TPM security chip from STMicroelectronics working with
an I2C, in menuconfig or .config choose the tpm driver on
device --> tpm and activate the protocol of your choice before compiling
the kernel.
The driver will be accessible from within Linux.
Tested on linux x86/x64, beagleboard REV B & XM REV C and CHROMIUM OS
Signed-off-by: Mathias Leblanc <mathias.leblanc@st.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Store the i2c_client struct in the vendor private pointer. Get rid of
the unnecessary include/linux/i2c/ header. Moved include files into the
driver c file. Fix smatch warnings. Make use of module_i2c_driver().
Removed unused code from the tpm_stm_st33_i2c.h file. Fix return
variable signedness in tpm_stm_i2c_send() and tpm_st33_i2c_probe().
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
"data" was too generic a name for what's being used as a generic
private pointer by vendor-specific code. Rename it to "priv" and provide
a #define for users.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
* STMicroelectronics version 1.2.0, Copyright (C) 2010
* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
* This is free software, and you are welcome to redistribute it
* under certain conditions.
This is the driver for TPM chip from ST Microelectronics.
If you have a TPM security chip from STMicroelectronics working with
an I2C, in menuconfig or .config choose the tpm driver on
device --> tpm and activate the protocol of your choice before compiling
the kernel.
The driver will be accessible from within Linux.
Tested on linux x86/x64 on kernel 3.x
Signed-off-by: Mathias Leblanc <mathias.leblanc@st.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Bool initializations should use true and false. Bool tests don't need
comparisons. Based on contributions from Joe Perches, Rusty Russell
and Bruce W Allan.
The semantic patch that makes this output is available
in scripts/coccinelle/misc/boolinit.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This seems to be preferred these days.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The TPM will respond to TPM_GET_CAP with TPM_ERR_INVALID_POSTINIT if
TPM_STARTUP has not been issued. Detect this and automatically
issue TPM_STARTUP.
This is for embedded applications where the kernel is the first thing
to touch the TPM.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch changes the semantics of the duration calculation for an
ordinal, by masking out the higher bits of a tpm command, which specify
whether it's an TPM_PROTECTED_COMMAND, TPM_UNPROTECTED_COMMAND,
TPM_CONNECTION_COMMAND, TPM_CONNECTION_COMMAND, TPM_VENDOR_COMMAND.
(See TPM Main Spec Part 2 Section 17 for details).
For all TPM_PROTECTED and TPM_CONNECTION commands the results are
unchanged.
The TPM_UNPROTECTED commands are TSS commands and thus irrelevant as
they are not sent to the tpm.
For vendor commands the semantics change for ordinals 10 and 11 but
they were probably wrong anyway.
For everything else which has the ordinal set to 10 or 11 the semantics
change as it now uses TPM_UNDEFINED instead of TPM_SHORT which was
probably wrong anyway (but irrelevant as not defined by the standard).
This patch also gets rid of the (false positive) smatch warning:
drivers/char/tpm/tpm.c:360 tpm_calc_ordinal_duration() error: buffer
overflow 'tpm_protected_ordinal_duration' 12 <= 243
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The entries in tpm_protected_ordinal_duration are exactly the same as
the first 12 in tpm_ordinal_duration, so we can simply remove this one,
and save some bytes.
This does not change the behavior of the driver.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Remove MIN, MAX and ABS macros that are duplicates kernel's native
implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
In existing use case, copying of the decoded data is unnecessary in
pkcs_1_v1_5_decode_emsa. It is just enough to get pointer to the message.
Removing copying and extra buffer allocation.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Different hooks can require different methods for appraising a
file's integrity. As a result, an integrity appraisal status is
cached on a per hook basis.
Only a hook specific rule, requires the inode to be re-appraised.
This patch eliminates unnecessary appraisals.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
With the new IMA policy 'appraise_type=' option, different hooks
can require different methods for appraising a file's integrity.
For example, the existing 'ima_appraise_tcb' policy defines a
generic rule, requiring all root files to be appraised, without
specfying the appraisal method. A more specific rule could require
all kernel modules, for example, to be signed.
appraise fowner=0 func=MODULE_CHECK appraise_type=imasig
appraise fowner=0
As a result, the integrity appraisal results for the same inode, but
for different hooks, could differ. This patch caches the integrity
appraisal results on a per hook basis.
Changelog v2:
- Rename ima_cache_status() to ima_set_cache_status()
- Rename and move get_appraise_status() to ima_get_cache_status()
Changelog v0:
- include IMA_APPRAISE/APPRAISED_SUBMASK in IMA_DO/DONE_MASK (Dmitry)
- Support independent MODULE_CHECK appraise status.
- fixed IMA_XXXX_APPRAISE/APPRAISED flags
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
In preparation for hook specific appraise status results, increase
the iint flags size.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
The 'security.ima' extended attribute may contain either the file data's
hash or a digital signature. This patch adds support for requiring a
specific extended attribute type. It extends the IMA policy with a new
keyword 'appraise_type=imasig'. (Default is hash.)
Changelog v2:
- Fixed Documentation/ABI/testing/ima_policy option syntax
Changelog v1:
- Differentiate between 'required' vs. 'actual' extended attribute
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
This patch forbids write access to files with digital signatures, as they
are considered immutable.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Define a new function ima_d_path(), which returns the full pathname.
This function will be used further, for example, by the directory
verification code.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
This patch reduces size of the iint structure by 8 bytes.
It saves about 15% of iint cache memory.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Hexdump is not really helping. Audit messages prints error messages.
Remove it.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Based on the IMA appraisal policy, files are appraised. For those
files appraised, the IMA hooks return the integrity appraisal result,
assuming IMA-appraisal is in enforcing mode. This patch combines
both of these criteria (in policy and enforcing file integrity),
removing the checking duplication.
Changelog v1:
- Update hook comments
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
When a file system is mounted read-only, setting the xattr value in
fix mode fails with an error code -EROFS. The xattr should be fixed
after the file system is remounted read-write. This patch verifies
that the set xattr succeeds, before setting the appraise status value
to INTEGRITY_PASS.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
EVM cannot be built as a kernel module. Remove the unncessary __exit
functions.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Although the IMA policy does not change, the LSM policy can be
reloaded, leaving the IMA LSM based rules referring to the old,
stale LSM policy. This patch updates the IMA LSM based rules
to reflect the reloaded LSM policy.
Reported-by: Sven Vermeulen <sven.vermeulen@siphos.be>
tested-by: Sven Vermeulen <sven.vermeulen@siphos.be>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Eric Paris <eparis@parisplace.org>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Pull LED fix from Bryan Wu.
* 'fixes-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: leds-gpio: set devm_gpio_request_one() flags param correctly
commit a99d76f leds: leds-gpio: use gpio_request_one
changed the leds-gpio driver to use gpio_request_one() instead
of gpio_request() + gpio_direction_output()
Unfortunately, it also made a semantic change that breaks the
leds-gpio driver.
The gpio_request_one() flags parameter was set to:
GPIOF_DIR_OUT | (led_dat->active_low ^ state)
Since GPIOF_DIR_OUT is 0, the final flags value will just be the
XOR'ed value of led_dat->active_low and state.
This value were used to distinguish between HIGH/LOW output initial
level and call gpio_direction_output() accordingly.
With this new semantic gpio_request_one() will take the flags value
of 1 as a configuration of input direction (GPIOF_DIR_IN) and will
call gpio_direction_input() instead of gpio_direction_output().
int gpio_request_one(unsigned gpio, unsigned long flags, const char *label)
{
..
if (flags & GPIOF_DIR_IN)
err = gpio_direction_input(gpio);
else
err = gpio_direction_output(gpio,
(flags & GPIOF_INIT_HIGH) ? 1 : 0);
..
}
The right semantic is to evaluate led_dat->active_low ^ state and
set the output initial level explicitly.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reported-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes some small errors in the new da9055 driver, eliminates a
compiler warning and adds DT support for the twl4030_wdt driver (so
that we can have multiple watchdogs with DT on the omap platforms)."
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: twl4030_wdt: add DT support
watchdog: omap_wdt: eliminate unused variable and a compiler warning
watchdog: da9055: Don't update wdt_dev->timeout in da9055_wdt_set_timeout error path
watchdog: da9055: Fix invalid free of devm_ allocated data
PCI: Reduce Ricoh 0xe822 SD card reader base clock frequency to 50MHz
PCI: Remove spurious error for sriov_numvfs store and simplify flow
PCI: Add PCIe Link Capability link speed and width names
PCI/PM: Do not suspend port if any subordinate device needs PME polling
PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=Ehs+
-----END PGP SIGNATURE-----
Merge tag '3.8-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Some fixes for v3.8. They include a fix for the new SR-IOV sysfs
management support, an expanded quirk for Ricoh SD card readers, a
Stratus DMI quirk fix, and a PME polling fix."
* tag '3.8-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Reduce Ricoh 0xe822 SD card reader base clock frequency to 50MHz
PCI/PM: Do not suspend port if any subordinate device needs PME polling
PCI: Add PCIe Link Capability link speed and width names
PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)
PCI: Remove spurious error for sriov_numvfs store and simplify flow
Commit 56c176c9ca ("UAPI: strip the _UAPI prefix from header guards
during header installation") strips the _UAPI prefix from header guards,
but only if there's a single space between the cpp directive and the
label.
Make it more flexible and able to handle tabs and multiple white space
characters.
Signed-off-by: David Howells <dhowell@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Empty files can get deleted by the patch program, so remove empty Kbuild
files and their links from the parent Kbuilds.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
overwriting a full page in the eCryptfs page cache, skip reading in and
decrypting the corresponding lower page.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JNeQ
-----END PGP SIGNATURE-----
Merge tag 'ecryptfs-3.8-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Two self-explanatory fixes and a third patch which improves
performance: when overwriting a full page in the eCryptfs page cache,
skip reading in and decrypting the corresponding lower page."
* tag 'ecryptfs-3.8-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
fs/ecryptfs/crypto.c: make ecryptfs_encode_for_filename() static
eCryptfs: fix to use list_for_each_entry_safe() when delete items
eCryptfs: Avoid unnecessary disk read and data decryption during writing
Pull Ceph fixes from Sage Weil:
"Two of Alex's patches deal with a race when reseting server
connections for open RBD images, one demotes some non-fatal BUGs to
WARNs, and my patch fixes a protocol feature bit failure path."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: fix protocol feature mismatch failure path
libceph: WARN, don't BUG on unexpected connection states
libceph: always reset osds when kicking
libceph: move linger requests sooner in kick_requests()
Sasha was fuzzing with trinity and reported the following problem:
BUG: sleeping function called from invalid context at kernel/mutex.c:269
in_atomic(): 1, irqs_disabled(): 0, pid: 6361, name: trinity-main
2 locks held by trinity-main/6361:
#0: (&mm->mmap_sem){++++++}, at: [<ffffffff810aa314>] __do_page_fault+0x1e4/0x4f0
#1: (&(&mm->page_table_lock)->rlock){+.+...}, at: [<ffffffff8122f017>] handle_pte_fault+0x3f7/0x6a0
Pid: 6361, comm: trinity-main Tainted: G W
3.7.0-rc2-next-20121024-sasha-00001-gd95ef01-dirty #74
Call Trace:
__might_sleep+0x1c3/0x1e0
mutex_lock_nested+0x29/0x50
mpol_shared_policy_lookup+0x2e/0x90
shmem_get_policy+0x2e/0x30
get_vma_policy+0x5a/0xa0
mpol_misplaced+0x41/0x1d0
handle_pte_fault+0x465/0x6a0
This was triggered by a different version of automatic NUMA balancing
but in theory the current version is vunerable to the same problem.
do_numa_page
-> numa_migrate_prep
-> mpol_misplaced
-> get_vma_policy
-> shmem_get_policy
It's very unlikely this will happen as shared pages are not marked
pte_numa -- see the page_mapcount() check in change_pte_range() -- but
it is possible.
To address this, this patch restores sp->lock as originally implemented
by Kosaki Motohiro. In the path where get_vma_policy() is called, it
should not be calling sp_alloc() so it is not necessary to treat the PTL
specially.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
which could cause file system corruptions when performing file punch
operations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=9R/D
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Various bug fixes for ext4. Perhaps the most serious bug fixed is one
which could cause file system corruptions when performing file punch
operations."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid hang when mounting non-journal filesystems with orphan list
ext4: lock i_mutex when truncating orphan inodes
ext4: do not try to write superblock on ro remount w/o journal
ext4: include journal blocks in df overhead calcs
ext4: remove unaligned AIO warning printk
ext4: fix an incorrect comment about i_mutex
ext4: fix deadlock in journal_unmap_buffer()
ext4: split off ext4_journalled_invalidatepage()
jbd2: fix assertion failure in jbd2_journal_flush()
ext4: check dioread_nolock on remount
ext4: fix extent tree corruption caused by hole punch
Remove the unused argument (formerly no_context) from mpol_parse_str()
and from mpol_to_str().
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently I suggested using "mount -o remount,mpol=local /tmp" in NUMA
mempolicy testing. Very nasty. Reading /proc/mounts, /proc/pid/mounts
or /proc/pid/mountinfo may then corrupt one bit of kernel memory, often
in a page table (causing "Bad swap" or "Bad page map" warning or "Bad
pagetable" oops), sometimes in a vm_area_struct or rbnode or somewhere
worse. "mpol=prefer" and "mpol=prefer:Node" are equally toxic.
Recent NUMA enhancements are not to blame: this dates back to 2.6.35,
when commit e17f74af35 "mempolicy: don't call mpol_set_nodemask() when
no_context" skipped mpol_parse_str()'s call to mpol_set_nodemask(),
which used to initialize v.preferred_node, or set MPOL_F_LOCAL in flags.
With slab poisoning, you can then rely on mpol_to_str() to set the bit
for node 0x6b6b, probably in the next page above the caller's stack.
mpol_parse_str() is only called from shmem_parse_options(): no_context
is always true, so call it unused for now, and remove !no_context code.
Set v.nodes or v.preferred_node or MPOL_F_LOCAL as mpol_to_str() might
expect. Then mpol_to_str() can ignore its no_context argument also,
the mpol being appropriately initialized whether contextualized or not.
Rename its no_context unused too, and let subsequent patch remove them
(that's not needed for stable backporting, which would involve rejects).
I don't understand why MPOL_LOCAL is described as a pseudo-policy:
it's a reasonable policy which suffers from a confusing implementation
in terms of MPOL_PREFERRED with MPOL_F_LOCAL. I believe this would be
much more robust if MPOL_LOCAL were recognized in switch statements
throughout, MPOL_F_LOCAL deleted, and MPOL_PREFERRED use the (possibly
empty) nodes mask like everyone else, instead of its preferred_node
variant (I presume an optimization from the days before MPOL_LOCAL).
But that would take me too long to get right and fully tested.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EPOLL_CTL_MOD sets the interest mask before calling f_op->poll() to
ensure events are not missed. Since the modifications to the interest
mask are not protected by the same lock as ep_poll_callback, we need to
ensure the change is visible to other CPUs calling ep_poll_callback.
We also need to ensure f_op->poll() has an up-to-date view of past
events which occured before we modified the interest mask. So this
barrier also pairs with the barrier in wq_has_sleeper().
This should guarantee either ep_poll_callback or f_op->poll() (or both)
will notice the readiness of a recently-ready/modified item.
This issue was encountered by Andreas Voellmy and Junchang(Jason) Wang in:
http://thread.gmane.org/gmane.linux.kernel/1408782/
Signed-off-by: Eric Wong <normalperson@yhbt.net>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andreas Voellmy <andreas.voellmy@yale.edu>
Tested-by: "Junchang(Jason) Wang" <junchang.wang@yale.edu>
Cc: netdev@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to
probe when booting with DT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We forgot to delete this in the commit 4f4753d9 (watchdog: omap_wdt:
convert to devm_ functions), and as a result the following compilation
warning was introduced:
drivers/watchdog/omap_wdt.c: In function 'omap_wdt_remove':
drivers/watchdog/omap_wdt.c:299:19: warning: unused variable 'res' [-Wunused-variable]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Otherwise, WDIOC_GETTIMEOUT returns wrong value if set_timeout fails.
This patch also removes unnecessary ret variable in da9055_wdt_ping function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is not required to free devm_ allocated data. Since kref_put
needs a valid release function, da9055_wdt_release_resources()
is not deleted.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
