Since sata devices can take several seconds to recover the link on reset
the 0.5 seconds that libsas currently waits may not be enough. Instead
if we are rediscovering a phy that was previously attached to a sata
device let libata handle any resets to encourage the device to transmit
the initial fis.
Once sas_ata_hard_reset() and lldds learn how to honor 'deadline' libsas
should stop encountering phys in an intermediate state, until then this
will loop until the fis is transmitted or ->attached_sas_addr gets
cleared, but in the more likely initial discovery case we keep existing
behavior.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
lldds use the SAS_TASK_NEED_DEV_RESET interface to request that eh
perform a reset. In the sata device case defer the commands that
triggered the reset to libata-eh context so it can perform its pre and
post reset management.
In the sas_ata_post_internal() case the reset request is falling on deaf
ears as the sas_task is immediately destroyed without any reset action.
Since it is currently a nop, and likely superfluous given the conversion
to new-style libata-eh, just drop the request.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas-eh if it successfully aborts an ata command will hide the timeout
condition (AC_ERR_TIMEOUT) from libata. The command likely completes
with the all-zero task->task_status it started with. Instead, interpret
a TMF_RESP_FUNC_COMPLETE as the end of the sas_task but keep the scmd
around for libata-eh to handle.
Tested-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Until we have told the lldd to forget a task a timed out operation can
return from the hardware at any time. Since completion frees the task
we need to make sure that no tasks run their normal completion handler
once eh has decided to manage the task. Similar to
ata_scsi_cmd_error_handler() freeze completions to let eh judge the
outcome of the race.
Task collector mode is problematic because it presents a situation where
a task can be timed out and aborted before the lldd has even seen it.
For this case we need to guarantee that a task that an lldd has been
told to forget does not get queued after the lldd says "never seen it".
With sas_scsi_timed_out we achieve this with the ->task_queue_flush
mutex, rather than adding more time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We invoke task->task_done() to free the task in the eh case, but at this
point we are prepared for scsi_eh_flush_done_q() to finish off the scmd.
Introduce sas_end_task() to capture the final response status from the
lldd and free the task.
Also take the opportunity to kill this warning.
drivers/scsi/libsas/sas_scsi_host.c: In function ‘sas_end_task’:
drivers/scsi/libsas/sas_scsi_host.c:102:3: warning: case value ‘2’ not in enumerated type ‘enum exec_status’ [-Wswitch]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since sas_ata does not implement ->freeze(), completions for scmds and
internal commands can still arrive concurrent with
ata_scsi_cmd_error_handler() and sas_ata_post_internal() respectively.
By the time either of those is called libata has committed to completing
the qc, and the ATA_PFLAG_FROZEN flag tells sas_ata_task_done() it has
lost the race.
In the sas_ata_post_internal() case we take on the additional
responsibility of freeing the sas_task to close the race with
sas_ata_task_done() freeing the the task while sas_ata_post_internal()
is in the process of invoking ->lldd_abort_task().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Prior to the conversion to the new-style libata-eh sas_ata_task_done()
may have been the last opportunity to clean up the scmd, but now
libata-eh explicitly handles this case. It also races against sas-eh.
If a lldd completes a task after SAS_TASK_STATE_ABORTED is set it could
trigger a spurious decrement of shost->host_failed. Current lldds have
the band-aid of checking SAS_TASK_STATE_ABORTED before calling
->task_done(), but better to just let the scmds escalate to libata for
race free cleanup.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sas_discover_sata() notifies lldds of sata devices twice. Once to allow
the 'identify' to be sent, and a second time to allow aic94xx (the only
libsas driver that cares about sata_dev.identify) to setup NCQ
parameters before the device becomes known to the midlayer. Replace
this double notification and intervening 'identify' with an explicit
->lldd_ata_set_dmamode notification. With this change all ata internal
commands are issued by libata, so we no longer need sas_issue_ata_cmd().
The data from the identify command only needs to be cached in one
location so ata_device.id replaces domain_device.sata_dev.identify.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libata error handling provides for a timeout for link recovery. libsas
must not rescan for previously known devices in this interval otherwise
it may remove a device that is simply waiting for its link to recover.
Let libata-eh make the determination of when the link is stable and
prevent libsas (host workqueue) from taking action while this
determination is pending.
Using a mutex (ha->disco_mutex) to flush and disable revalidation while
eh is running requires any discovery action that may block on eh be
moved to its own context outside the lock. Probing ATA devices
explicitly waits on ata-eh and the cache-flush-io issued during device
removal may also pend awaiting eh completion. Essentially any rphy
add/remove activity needs to run outside the lock.
This adds two new cleanup states for sas_unregister_domain_devices()
'allocated-but-not-probed', and 'flagged-for-destruction'. In the
'allocated-but-not-probed' state dev->rphy points to a rphy that is
known to have not been through a sas_rphy_add() event. At domain
teardown check if this device is still pending probe and cleanup
accordingly. Similarly if a device has already been queued for removal
then sas_unregister_domain_devices has nothing to do.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In preparation for adding tracking of another device state "destroy".
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Each libsas driver (mvsas, pm8001, and isci) has invented a different
method for managing the ap->lock. The lock is held by the ata
->queuecommand() path. mvsas drops it prior to acquiring any internal
locks which allows it to hold its internal lock across calls to
task->task_done(). This capability is important as it is the only way
the driver can flush task->task_done() instances to guarantee that it no
longer has any in-flight references to a domain_device at
->lldd_dev_gone() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When an lldd invokes ->notify_port_event() it can trigger a chain of libsas
events to:
1/ form the port and find the direct attached device
2/ if the attached device is an expander perform domain discovery
A call to flush_workqueue() will only flush the initial port formation work.
Currently libsas users need to call scsi_flush_work() up to the max depth of
chain (which will grow from 2 to 3 when ata discovery is moved to its own
discovery event). Instead of open coding multiple calls switch to use
drain_workqueue() to flush sas work.
drain_workqueue() does not handle new work submitted during the drain so
libsas needs a bit of infrastructure to hold off unchained work submissions
while a drain is in flight. A lldd ->notify() event is considered 'unchained'
while a sas_discover_event() is 'chained'. As Tejun notes:
"For now, I think it would be best to add private wrapper in libsas to
support deferring unchained work items while draining."
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In preparation for adding new states (SAS_HA_DRAINING, SAS_HA_FROZEN),
convert ha->state into a set of flags.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The locks only served to make sure the pending event bitmask was updated
consistently.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
These are never freed in the nominal path. A domain_device has a
different lifetime than a sas_rphy we need a dev->rphy independent way
of identifying sata devices.
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Arrange for the deallocation of a struct domain_device object when it no
longer has:
1/ any children
2/ references by any scsi_targets
3/ references by a lldd
The comment about domain_device lifetime in
Documentation/scsi/libsas.txt is stale as it appears mainline never had
a version of a struct domain_device that was registered as a kobject.
We now manage domain_device reference counts on behalf of external
agents.
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Per commit 3e4ec344 "libata: kill ATA_FLAG_DISABLED" needing to set
ATA_DEV_NONE is a holdover from before libsas converted to the
"new-style" ata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 1e34c838 "[SCSI] libsas: remove spurious sata control register
read/write" removed the routines to fake the presence of the sata
control registers, now remove the unused data structure fields to kill
any remaining confusion.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We have experienced several devices which fail in a fashion we do not
currently handle gracefully in SCSI. After a failure these devices will
respond to the SCSI primary command set (INQUIRY, TEST UNIT READY, etc.)
but any command accessing the storage medium will time out.
The following patch adds an callback that can be used by upper level
drivers to inspect the results of an error handling command. This in
turn has been used to implement additional checking in the SCSI disk
driver.
If a medium access command fails twice but TEST UNIT READY succeeds both
times in the subsequent error handling we will offline the device. The
maximum number of failed commands required to take a device offline can
be tweaked in sysfs.
Also add a new error flag to scsi_debug which allows this scenario to be
easily reproduced.
[jejb: fix up integer parsing to use kstrtouint]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The virtio-scsi HBA is the basis of an alternative storage stack
for QEMU-based virtual machines (including KVM). Compared to
virtio-blk it is more scalable, because it supports many LUNs
on a single PCI slot), more powerful (it more easily supports
passthrough of host devices to the guest) and more easily
extensible (new SCSI features implemented by QEMU should not
require updating the driver in the guest).
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some other older controllers also do have problems to perform a kdump.
Adding controllers to this list means that the driver will signal
this non-ability via a resettable flag correctly.
The unsupported list was created after a consultation with HP.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Permanent target failures are non-retryable and should be classified as
TARGET_ERROR; otherwise dm-multipath will retry an IO request that will
always fail at the target.
A SCSI command that fails with ILLEGAL_REQUEST sense and Additional
sense 0x20, 0x21, 0x24 or 0x26 represents a permanent TARGET_ERROR.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The provisioning_mode parameter in sysfs did not get updated in the
SD_LBP_DISABLE case. Make sure the provisioning mode is always set
correctly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The error reported up the stack for a discard failure did not clearly
indicate that the command was processed and subsequently failed by the
target device.
Return -EREMOTEIO so multipathing does not classify this condition as a
path failure.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The __get_free_pages can fail, so the return value should be checked.
Spotted thanks to Stanislaw.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added ping support for network connection diagnostics.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added ping support for iscsi adapter, application can use this
interface for diagnostic network connection.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support to post kernel host event to application using
netlink interface.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support to post kernel host event to application using
netlink interface.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On ROM lock acquiring timeout failure, driver spews lot of warning
messages in a for loop, remove the unwanted warning message to reduce
kernel messages clutter.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In some configurations user may not have boot targets configured.
In such cases the debug messages printed out by driver look like
some kind of failure happening. However this could be a valid
case, so modified the messages to appear as warning messages
versus failure messages.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla4xxx_verify_boot_idx can falsely report a DDB to be boot target
if ha->pri_ddb_idx and ha->sec_ddb_idx are not initialized correctly.
What this could cause is if there is DDB entry in FLash at index 0, then
qla4xxx_verify_boot_idx would return wrong result as ha->pri_ddb_idx is not
set correctly. Fixed the qla4xxx_get_boot_info to set the ha->pri_ddb_idx and
ha->sec_ddb_idx correctly.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix the un-necessary wait for completion of a sendtarget on an
invalid DDB entry. The state of an invalid DDB entry is 0 (unassigned)
This will also avoid the delays during system boot.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This code initially added for FW debugging, we don't need this
code now so taking it out.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While we wait for GPN_FT response, if the ctlr link goes down, the stack
generates a completion for GPN_FT with error FC_EXCH_CLOSED, and reports a
discovery error. Discovery is not retried in this case, and rightly so.
However, the 'pending' flag stays set, which does not allow subsequent
discovery to succeed as GPN_FT will never be issued. Fix it by clearing the
pending flag when the discovery fails due to GPN_FT failure.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adding and removing the host into the zone causes this panic.
BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0
IP: [<ffffffffa0491707>] fc_exch_recv+0xc57/0xe70 [libfc]
Call Trace:
[<ffffffffa050e04b>] bnx2fc_l2_rcv_thread+0x37b/0x430 [bnx2fc]
[<ffffffffa050dcd0>] ? bnx2fc_l2_rcv_thread+0x0/0x430 [bnx2fc]
[<ffffffff81090886>] kthread+0x96/0xa0
[<ffffffff8100c14a>] child_rip+0xa/0x20
[<ffffffff810907f0>] ? kthread+0x0/0xa0
[<ffffffff8100c140>] ? child_rip+0x0/0x20
During fc_exch_reset, the active exchanges are aborted and the exch is deleted.
As part of processing ABTS response, due to 'ep' being NULL, any access to ep in
fc_exch_recv_bls() causes this panic. Fixed to access 'ep' only if non-NULL.
Reviewed-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The reference counting was necessary on these instances
because it was possible for NPIV ports to be destroyed
after the N_Port. A previous patch ensures that all NPIV
ports are destroyed before the N_Port making the need to
track references on the interface unnecessary.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently all port deletion is routed though the FCoE
workqueue (fcoe_wq). When fc_remove_host is called on
an N_Port (for example, from fcoe_destroy) the vports
are queued into a FC Transport workqueue. fc_remove_host
flushes that queue and each vport is passed to fcoe's
fcoe_vport_destroy, which simply queues the associated
fcoe_ports for later deletion. This queue cannot be
flushed within the N_Ports destroy path because of
circular locking issues. The result is that the NPIV
ports are destroyed after the N_Port, which is reverse
of how they are created.
This quirk causes fcoe to keep references on the
fcoe_interface shared by each of these ports (N_Port
and NPIV). Changing the ordering such that NPIV ports
are destroyed before the N_Port will allow us to remove
reference counting on the fcoe_interface instances.
This patch simply allows fcoe_vport_destory to destroy
NPIV ports without deferring them to a workqueue context.
This ensures that when fc_remove_host is called the
NPIV ports will be destroyed first before the N_Port and
allows reference counting on the fcoe's fcoe_interface
to be remove in a later patch.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The label implies that it should be called when
there is 'nomod.' I read that to mean that the
module reference 'get' failed. However, it's only
called when the module reference 'get' succeeded.
I think it makes more sense to name the label,
'out_putmod' since it should be called when we
need to 'put' the module reference taken in the
routine before returning.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow FDMI attributes to be exposed via the fc_host
class object for the fcoe driver.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is more of a debug statement. As a KERN_ERR we generate
log entries anytime any netdev goes up or down, so when booting
there are notification log entries for all system interfaces
including 'lo'. This is too much. Let's just log when necessary.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows the controller to do WRITE_INSERT and READ_STRIP for SAS
disks that support protection information. SAS disks must be formatted
with protection information to use this feature via sg_format.
sg3_utils-1.32 -- sg_format version 1.19 20110730
sg_format usage:
sg_format --format --verbose --pinfo /dev/sda
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A device logout sent in the delete path of a fcport would clear the
port handle binding inside the firmware. This could lead to queued
work items for the fcport, if any, getting incorrect results. This
patch fixes the issue by checking for device name changes after a
call to get port database.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add a field to the qla_hw_data struct to allow us to set the maximum number of
fabric devices on a per adapter basis based on ISP type.
[jejb: fix up missing rval = QLA_SUCCESS to prevent uninit var warning]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rather than continuously allocating and freeing swl within the discovery
process, simply pre-allocate it the first time that it's needed, cache it
through the rest of the lifecycle of the driver and free it at module unload.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Don't use default 30 second mailbox-command timeout for these
serial requests, instead, limit the TMO to the standard 2*RATOV
plus some fudge-factor.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During command failure/non-recognition, the upper-layer
FC-transport expects the drivers to set
job-reply->reply_payload_rcv_len. Do this in a consistent manner
to avoid duplication.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During rport tear-down, make sure we do an implicit LOGO of the fcport in our
firmware to try to clear any residual commands associated with that fcport.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make sure that all calls to ha->isp_ops->fabric_login() check the
return value for failure.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When thermal temperature initially fails, return a blank string to the
sysfs interface. This fixes the initial display of 0.00 followed by
subsequent display of blank line; the initial 0.00 should have not
displayed for cards that do not support thermal temperature.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of processing each RSCN individually, use only the name server results
from the switch to tell the existance of a given fcport.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver is logging a slew of 'good' status requests for ELS/CT passthrough
commands. Change some log messages from:
* ql_log() -> ql_dbg()
* ql_log_info -> ql_dbg_user
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rework the structures related to SRB processing to minimize the memory
allocations per I/O and manage resources associated with and completions
from common routines.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Original 'defaults' were not OUI valid.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added Sync. mode to support Series 7/8/9 controller families: This is a
compatibility mode for all these controller families. The Async. (Performance)
mode can be changed in the future. First Async. mode version added for Series
7; Controller parameter aac_sync_mode added
Signed-off-by: Mahesh Rajashekhara <aacraid@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The error_mask module param overrides has a bug which prevented
the new module param values to take effect.
Also changed the type attribute of the error_mask1/2 module params
from int to uint to allow the MSB to be set.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
bnx2i_percpu_thread_create() create per cpu kthread, and should use
proper NUMA aware API.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If 'drv_fcxp = kzalloc(sizeof(struct bfad_fcxp), GFP_KERNEL);' fails
and returns NULL, then we'll leak the memory allocated to 'bsg_fcpt'
when we jump to 'out:' and the variable subsequently goes out of
scope.
Also remove the cast of the kzalloc() return value. kzalloc() returns
a void* which is implicitly converted, so the explicit cast is
pointless.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Enabling clock gating for power savings on entry to controller ready
state. Disable SCU clock gating for power savings on exit from the
controller ready state.
The gating is fully automated by silicon after setting the mode.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the driver/lib has called scsi_done and cleaned up internally but
scsi layer has not yet called blk_mark_rq_complete when the command
times out we hit a problem if the timeout code calls blk_mark_rq_complete first.
When the time out code calls into the driver we were returning
BLK_EH_RESET_TIMER and that causes the timeout code to just call
us again later.
We need to be calling BLK_EH_HANDLED so the timeout code can complete
the completion process because it had called blk_mark_rq_complete
on the command and now owns its processing.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem description from Xi Wang:
A large max_r2t could lead to integer overflow in subsequent call to
iscsi_tcp_r2tpool_alloc(), allocating a smaller buffer than expected
and leading to out-of-bounds write.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
NETLINK_CREDS's pid now returns 0, so I guess we are supposed to
be using NETLINK_CB. This changed while the patch to export the
pid was getting merged upstream, so it was not noticed until both
the network and iscsi changes were in the same tree.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes the host byte settings DID_TARGET_FAILURE and
DID_NEXUS_FAILURE. The function __scsi_error_from_host_byte, tries to reset
the host byte to DID_OK. But that does not happen because of the OR operation.
Here is the flow.
scsi_softirq_done-> scsi_decide_disposition -> __scsi_error_from_host_byte
Let's take an example with DID_NEXUS_FAILURE. In scsi_decide_disposition,
result will be set as DID_NEXUS_FAILURE (=0x11). Then in
__scsi_error_from_host_byte, when we do OR with DID_OK. Purpose is to reset
it back to DID_OK. But that does not happen. This patch fixes this issue.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When there are 255 NPIV ports, and the interface is brought down & up, both
physical and NPIV ports are logged off and never logged back in. Since
discovery happens on single CPU, XID resources on that CPU will be limited,
which when exhausted the discovery fails. Increase the XID resource range to
ensure that the discovery completes successfully. Also ensure that
fc_exch_mgr_alloc() doesn't fail on the system that has lower number of CPUs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Host drops sessions when flood of unsolicited LOGOs are received from the
target. Because of unsufficient PLOGI retries, upon exceeding the retry count
of 3, the target sessions are dropped. Increased the retry count to 255 to
allow sufficient retries in this scenario.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
System panics while accessing stale pointer - timer_work_queue - in the IO path
before bnx2fc_stop is called. Fix is to destroy the workqueue after the destroy
operation is complete.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow FDMI attributes to be exposed via the fc_host
class object for the fcoe driver.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This adds support for updating the FC-GS FDMI attributes
in the fcoe driver.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support for Fabric Device Management
Interface as per FC-GS-4 spec. in libfc. Any driver
making use of libfc can enable fdmi state machine
for a given lport.
If lport has enabled FDMI support the lport state
machine will transition into FDMI after completing
the DNS states and before entering the SCR state.
The FDMI state transition is such that if there is an
error, it won't stop the lport state machine from
transitioning and the it will behave as if there was
no FDMI support.
The FDMI HBA attributes are registed with the Management
server via Register HBA (RHBA) command and the port
attributes are reigstered using the Register Port(RPA)
command.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently the libfc Common Transport(CT) calls assume that
the CT requests are Name Server specific only. This patch
makes it more flexible to allow more FC-GS services to make
use of these routines.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This adds FC-GS Fabric Device Management Interface
(FDMI) related attributes to fc_host_attr structure.
This is in preparation for allowing FDMI attributes
to be registered via libfc.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use find_first_zero_bit to find the first cleared bit in a memory region.
This also includes the following minor changes.
- Use bitmap_zero
- Reduce unnecessary atomic bitops usage
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The SCSI GET LBA STATUS command was introduced in SBC-3 revision
20 in September 2009. At that time the Parameter Data Length
field in the response had an associated byte offset of 8.
Then in SBC-3 revision 25 (October 2010) that byte offset was
changed to 4. The sg_get_lba_status utility in sg3_utils version
1.33 (released earlier today) has been changed to calculate
the newer response length. However the implementation of
GET LBA STATUS command in the scsi_debug driver still uses the
original byte offset.
modify the Parameter Data Length field value in the GET LBA STATUS command
response to comply with the change in SBC-3 revision 25
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Certain types of changes to devices should not be interpreted as a device
change that would cause the device to be removed and re-added. These include
RAID level and Firmware revision changes. However, these attribute changes DO
need to be reflected in the controller info structure's dev structure list, so
that sysfs and /proc info files for the devices will reflect the new values.
Signed-off-by: Scott Teel <scott.stacy.teel@hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reduce confusion and inaccuracy caused by dated naming of vars and functions
referring to external target devices.
CURRENT NAMING: PROPOSED NAMING:
"MSA2xxx devices" "external target devices"
msa2xxx_model ext_target_model
is_msa2xxx is_ext_target
add_msa2xxx_enclosure add_ext_target_dev
nmsa2xxx_enclosures n_ext_target_devs
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver limits SAS external target IDs to range 1-8.
Need to increase limit and clean up overlapping concepts of targets and paths
in the code.
There are several defined constants that control this:
HPSA_MAX_TARGETS_PER_CTLR 16
MAX_MSA2XXX_ENCLOSURES 32
HPSA_MAX_PATHS 8
We can condense this to one constant:
MAX_EXT_TARGETS 32
SAS switches allow for 8 connections, and there is capacity for 4 switches per
enclosure in largest blade enclosure type.
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It should call hpsa_set_bus_target_lun rather
than individually setting bus, target and lun.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some distros have a "rescan-scsi-bus.sh" script which depends on
SCSI REPORT LUNs not reporting something different than what the
driver tells the kernel, even if the driver uses scan_start and
scan_finished methods of the SCSI host template to override the
usual SCSI midlayer discovery code. Previously, 1 was added to
the LUN to make room to insert the RAID controller device at
LUN 0. Now, the RAID controller is moved to bus 3, and 1 is no
longer added to the LUN. However, SCSI REPORT LUNS on Smart Array
doesn't report physical devices like tape drives or auto-loaders
as it turns out, so those particular device types still won't match.
Generally the logical drives are reported first however, so at
least those should match.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Upgraded firmware on Smart Array P7xx (and some others) made them show up as
SCSI revision 5 devices and this caused the driver to fail to map MSA2xxx
logical drives to the correct bus/target/lun. A symptom of this would be that
the target ID of the logical drives as presented by the external storage array
is ignored, and all such logical drives are assigned to target zero,
differentiated only by LUN. Some multipath software reportedly does not deal
well with this behavior, failing to recognize different paths to the same
device as such.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sometimes, for testing purposes (e.g. testing rmmod on a system
that normally boots using hpsa) it's nice to rename the driver
and split it into two drivers and restrict it to certain
controllers. This makes that easier.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
hpsa_register_scsi just calls hpsa_scsi_detect. Move
the guts of hpsa_scsi_detect into hpsa_register_scsi and
get rid of hpsa_scsi_detect.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We had both h->max_sg_entries and h->maxsgentries in the per controller
structure which is terribly confusing. max_sg_entries was really
just a constant, 32, which defines how big the "block fetch table"
is, which is as large as the max number of SG elements embedded
within a command (excluding SG elements in chain blocks).
MAXSGENTRIES was the constant used to denote the max number of SG
elements embedded within a command, also a poor name.
So renamed MAXSGENTREIS to SG_ENTRIES_IN_CMD, and removed
h->max_sg_entries and replaced it with SG_ENTRIES_IN_CMD.
h->maxsgentries is unchanged, and is the maximum number of sg
elements the controller will support in a command, including
those in chain blocks, minus 1 for the chain block pointer..
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Note: this is a replacement patch for the issue pointed out in
http://www.gossamer-threads.com/lists/linux/kernel/1477270
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC Discovery state machine fixes.
- Fix bug with driver returning the inactive ndlp (125743)
- Fix discovery problem when in pt2pt by copying old ndlp state before
state change (126887)
- Fix ndlp nodelist not empty wait timeout during driver unloading (127052)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
T10 Diff fixes and enhancements:
- Add SLI4 Lancer support for T10 DIF / BlockGuard (121980)
- Fix SLI4 BlockGuard behavior when protection data is generated by HBA (121980)
- Enhance debugfs for injecting T10 DIF errors (123966, 132966)
- Fix Incorrect usage of bghm for BlockGuard errors (127022)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
SLI related fixes:
- Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state (126230)
- Fix ELS FDISC failing with local reject / invalid RPI. (126350)
- Fix reset port when reset is needed during fw_dump (125807)
- Fix unbounded firmware revision string from port cause panic (126560)
- Fix driver behavior when receiving an ADISC (126654)
- Fix driver not returning when bad ndlp found in abts error event
handling (126209)
- Add more driver logs in area of SLI4 port error attention and reset
recovery (126813, 124466)
- Fix failure in handling large CQ/EQ identifiers in an IOV
environment (126856)
- Fix for driver using duplicate RPIs after lancer port reset (126723)
- Clear vport->fc_myDID in lpfc_els_issue_fdisc to guarentee a
zero SID (126779, 126897)
- Fix for SLI4 Port delivery for BLS ABORT ACC (126289)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
BSG and User interface fixes:
- Fix driver processing an els command using 16Gb FC Adapter (126345)
- Change SLI4 FC port internal loopback to inner internal (126409)
- Fix bug with driver dump command type 4 using 16Gb FC Adapter (126406)
- Create character device to take a reference on the driver (126082)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
IO_XFER_ERROR_BREAK and IO_XFER_OPEN_RETRY_TIMEOUT are deficient of the
required actions as outlined in the programming manual for the pm8001. Due to
the overlapping code requirements of these recovery responses, we found it
necessary to bundle them together into one patch.
When a break is received during the command phase (ssp_completion), this is a
result of a timeout or interruption on the bus. Logic suggests that we should
retry the command.
When a break is received during the data-phase (ssp_event), the task must be
aborted on the target or it will retain a data-phase lock turning the target
reticent to all future media commands yet will successfully respond to TUR,
INQUIRY and ABORT leading eventually to target failure through several
abort-cycle loops.
The open retry interval is exceedingly short resulting in occasional target
drop-off during expander resets or when targets push-back during bad-block
remapping. Increased effective timeout from 130ms to 1.5 seconds for each try
so as to trigger after the administrative inquiry/tur timeout in the scsi
subsystem to keep error-recovery harmonics to a minimum.
When an open retry timeout event is received, the action required by the
targets is to issue an abort for the outstanding command then logic suggests
we retry the command as this state is usually an indication of a credit block
or busy condition on the target.
We hijacked the pm8001_handle_event work queue handler so that it will handle
task as an argument instead of device for the workers in support of the
deferred handling outlined above.
Moderate to Heavy bad-path testing on a 2.6.32 vintage kernel, compile-testing
on scsi-misc-2.6 kernel ...
Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jack noticed I dropped a patch fragment associated with a flags automatic
variable in mpi_set_phys_g3_with_ssc (ooops) and that the pre-emptive locking
that piggy-backed this patch was not in-fact necessary because of underlying
atomic accesses to the hardware. Here is the updated patch fixing these two
issues.
The pm8001 driver is missing the FUNC_GET_EVENTS handler in the phy control
function. Since the pm8001_bar4_shift function was not designed to be called
at runtime, added locking surrounding the adjustment for all accesses.
Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
pm8001_phy_control PHY_FUNC_HARD_RESET locks up on second try via
smp_phy_control because response HW_EVENT_PHY_START_STATUS fails to complete
previous command. The PM8001F_RUN_TIME flag is not treated as a bit, but a
state in all readers, yet once we are operational or in the run time state,
the flags use a bit-set operation.
Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This implements basic power management for SCSI tapes.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch (as1520) fixes a bug in the SCSI layer's power management
implementation.
LUN scanning can be carried out asynchronously in do_scan_async(), and
sd uses an asynchronous thread for the time-consuming parts of disk
probing in sd_probe_async(). Currently nothing coordinates these
async threads with system sleep transitions; they can and do attempt
to continue scanning/probing SCSI devices even after the host adapter
has been suspended. As one might expect, the outcome is not ideal.
This is what the "prepare" stage of system suspend was created for.
After the prepare callback has been called for a host, target, or
device, drivers are not allowed to register any children underneath
them. Currently the SCSI prepare callback is not implemented; this
patch rectifies that omission.
For SCSI hosts, the prepare routine calls scsi_complete_async_scans()
to wait until async scanning is finished. It might be slightly more
efficient to wait only until the host in question has been scanned,
but there's currently no way to do that. Besides, during a sleep
transition we will ultimately have to wait until all the host scanning
has finished anyway.
For SCSI devices, the prepare routine calls async_synchronize_full()
to wait until sd probing is finished. The routine does nothing for
SCSI targets, because asynchronous target scanning is done only as
part of host scanning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In do_scan_async(), calling scsi_autopm_put_host(shost) may reference
freed shost, and cause Posison overwitten warning.
Yes, this case can happen, for example, an USB is disconnected just
when do_scan_async() thread starts to run, then scsi_host_put() called
in scsi_finish_async_scan() will lead to shost be freed(because the
refcount of shost->shost_gendev decreases to 1 after USB disconnects),
at this point, if references shost again, system will show following
warning msg.
To make scsi_autopm_put_host(shost) always reference a valid shost,
put it just before scsi_host_put() in function
scsi_finish_async_scan().
[ 299.281565] =============================================================================
[ 299.281634] BUG kmalloc-4096 (Tainted: G I ): Poison overwritten
[ 299.281682] -----------------------------------------------------------------------------
[ 299.281684]
[ 299.281752] INFO: 0xffff880056c305d0-0xffff880056c305d0. First byte
0x6a instead of 0x6b
[ 299.281816] INFO: Allocated in scsi_host_alloc+0x4a/0x490 age=1688
cpu=1 pid=2004
[ 299.281870] __slab_alloc+0x617/0x6c1
[ 299.281901] __kmalloc+0x28c/0x2e0
[ 299.281931] scsi_host_alloc+0x4a/0x490
[ 299.281966] usb_stor_probe1+0x5b/0xc40 [usb_storage]
[ 299.282010] storage_probe+0xa4/0xe0 [usb_storage]
[ 299.282062] usb_probe_interface+0x172/0x330 [usbcore]
[ 299.282105] driver_probe_device+0x257/0x3b0
[ 299.282138] __driver_attach+0x103/0x110
[ 299.282171] bus_for_each_dev+0x8e/0xe0
[ 299.282201] driver_attach+0x26/0x30
[ 299.282230] bus_add_driver+0x1c4/0x430
[ 299.282260] driver_register+0xb6/0x230
[ 299.282298] usb_register_driver+0xe5/0x270 [usbcore]
[ 299.282337] 0xffffffffa04ab03d
[ 299.282364] do_one_initcall+0x47/0x230
[ 299.282396] sys_init_module+0xa0f/0x1fe0
[ 299.282429] INFO: Freed in scsi_host_dev_release+0x18a/0x1d0 age=85
cpu=0 pid=2008
[ 299.282482] __slab_free+0x3c/0x2a1
[ 299.282510] kfree+0x296/0x310
[ 299.282536] scsi_host_dev_release+0x18a/0x1d0
[ 299.282574] device_release+0x74/0x100
[ 299.282606] kobject_release+0xc7/0x2a0
[ 299.282637] kobject_put+0x54/0xa0
[ 299.282668] put_device+0x27/0x40
[ 299.282694] scsi_host_put+0x1d/0x30
[ 299.282723] do_scan_async+0x1fc/0x2b0
[ 299.282753] kthread+0xdf/0xf0
[ 299.282782] kernel_thread_helper+0x4/0x10
[ 299.282817] INFO: Slab 0xffffea00015b0c00 objects=7 used=7 fp=0x
(null) flags=0x100000000004080
[ 299.282882] INFO: Object 0xffff880056c30000 @offset=0 fp=0x (null)
[ 299.282884]
...
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Cc: stable@kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With IOs running and PegHalt testing the system reboots when memory reset is
performed during device initialization.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Complete the mailbox command timed out before initiating another abort cycle
to recover so that mailbox commands issued during next reset cycle don't fail
due to pending mailbox access timeout.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove the check for a NULL fcport so that the host reset will run
unconditionally to unwedge any commands before the device is offlined and to
prevent a quick runthrough of the SCSI error handling.
Signed-off-by: Michael Christie <mchristi@redhat.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ISP2200 adapters only have 24 mailbox registers so read only that many.
Reported-by: Olatunji Ruwase <oor@cs.cmu.edu>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This can cause instability in mailbox command state machine handling.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Not clearing the options flags in mbx1 could lead the firmware
into interpreting old data in mbx1 through mbx8. This could
lead to inadvertent DMA read/write operations to stale memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Many locations within the driver would use an inconsistent set of
checks to determine ISP-reset state. Consolidate the checks into
this inline-helper.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
NULL orom ptr passed in for verification which caused page fault.
We will set a default version when we don't have orom struct.
Reported-by: Dan Melnic <dan@seamicro.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In some scenarios, an EEH error can take a long time to be detected, since the
driver issues an MMIO read only after a device reset command times out and we
try to reset the adapter. This patch adds some code in ipr_cancel_op() to read
a hardware register so we detect the error earlier in case the op is being
aborted because of a timeout caused by a frozen adapter slot.
Another problem in such scenarios is that in __ipr_eh_host_reset() we change the
dump state flag from WAIT_FOR_DUMP to GET_DUMP, and the flag is later changed
from GET_DUMP to READ_DUMP in ipr_reset_restore_cfg_space(). However, if when
__ipr_eh_host_reset() is called by the SCSI error handling the function
ipr_reset_restore_cfg_space() has already been called by the PCI EEH code, we
end up with the flag in an inconsistent state. This patch also prevents this
problem.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If ioc->pci_error_recovery is set, goto out in mpt2sas_base_hard_reset_handler()
leads to unlock unheld ioc->reset_in_progress_mutex.
The patch fixes the issue by jumping afer mutex_unlock() call.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Says Jens:
"Time to push off some of the pending items. I really wanted to wait
until we had the regression nailed, but alas it's not quite there yet.
But I'm very confident that it's "just" a missing expire on exit, so
fix from Tejun should be fairly trivial. I'm headed out for a week on
the slopes.
- Killing the barrier part of mtip32xx. It doesn't really support
barriers, and it doesn't need them (writes are fully ordered).
- A few fixes from Dan Carpenter, preventing overflows of integer
multiplication.
- A fixup for loop, fixing a previous commit that didn't quite solve
the partial read problem from Dave Young.
- A bio integer overflow fix from Kent Overstreet.
- Improvement/fix of the door "keep locked" part of the cdrom shared
code from Paolo Benzini.
- A few cfq fixes from Shaohua Li.
- A fix for bsg sysfs warning when removing a file it did not create
from Stanislaw Gruszka.
- Two fixes for floppy from Vivek, preventing a crash.
- A few block core fixes from Tejun. One killing the over-optimized
ioc exit path, cleaning that up nicely. Two others fixing an oops
on elevator switch, due to calling into the scheduler merge check
code without holding the queue lock."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix lockdep warning on io_context release put_io_context()
relay: prevent integer overflow in relay_open()
loop: zero fill bio instead of return -EIO for partial read
bio: don't overflow in bio_get_nr_vecs()
floppy: Fix a crash during rmmod
floppy: Cleanup disk->queue before caling put_disk() if add_disk() was never called
cdrom: move shared static to cdrom_device_info
bsg: fix sysfs link remove warning
block: don't call elevator callbacks for plug merges
block: separate out blk_rq_merge_ok() and blk_try_merge() from elevator functions
mtip32xx: removed the irrelevant argument of mtip_hw_submit_io() and the unused member of struct driver_data
block: strip out locking optimization in put_io_context()
cdrom: use copy_to_user() without the underscores
block: fix ioc locking warning
block: fix NULL icq_cache reference
block,cfq: change code order
Quoth David:
1) GRO MAC header comparisons were ethernet specific, breaking other
link types. This required a multi-faceted fix to cure the originally
noted case (Infiniband), because IPoIB was lying about it's actual
hard header length. Thanks to Eric Dumazet, Roland Dreier, and
others.
2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
From Anisse Astier.
3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.
4) ipv4 TCP reset generation needs to respect any network interface
binding from the socket, otherwise route lookups might give a
different result than all the other segments received. From Shawn
Lu.
5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
Graf.
6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.
7) Revert skge PCI mapping changes that are causing crashes for some
folks, from Stephen Hemminger.
8) IPV4 route lookups fill in the wildcarded fields of the given flow
lookup key passed in, which is fine most of the time as this is
exactly what the caller's want. However there are a few cases that
want to retain the original flow key values afterwards, so handle
those cases properly. Fix from Julian Anastasov.
9) IGB/IXGBE VF lookup bug fixes from Greg Rose.
10) Properly null terminate filename passed to ethtool flash device
method, from Ben Hutchings.
11) S3 resume fix in via-velocity from David Lv.
12) Fix double SKB free during xmit failure in CAIF, from Dmitry
Tarnyagin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
netprio_cgroup: don't allocate prio table when a device is registered
netprio_cgroup: fix an off-by-one bug
bna: fix error handling of bnad_get_flash_partition_by_offset()
isdn: type bug in isdn_net_header()
net: Make qdisc_skb_cb upper size bound explicit.
ixgbe: ethtool: stats user buffer overrun
ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
ixgbe: do not update real num queues when netdev is going away
ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
ixgbe: Fix case of Tx Hang in PF with 32 VFs
ixgbe: fix vf lookup
igb: fix vf lookup
e1000: add dropped DMA receive enable back in for WoL
gro: more generic L2 header check
IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
net: enable TC35815 for MIPS again
...
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/radeon: do not continue after error from r600_ib_test
drivers/gpu/drm/drm_ioc32.c: initialize all fields
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KZgACgkQMUfUDdst+yk0HgCeIdU3VTWqdxZDXp3G1sFIXZ1b
47YAnRAMAar+/aLaNhqGrcz7aa5y2cUU
=8sr8
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Serial/TTY fixes for the 3.3-rc3 tree
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
m32r: relocate drivers back out of 8250 dir
tty: fix a build failure on sparc
serial: samsung: Add support for EXYNOS5250
serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KLYACgkQMUfUDdst+ykhiwCg2ctSu4umygA1ErAedAA+sJkv
psYAn20OZQDyuBcBAIzL2L+Y/BUz8bXt
=xvyx
-----END PGP SIGNATURE-----
Merge tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Staging tree patches for 3.3-rc3
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
staging: pohmelfs: remove drivers/staging/pohmelfs
staging: android/ram_console: Don't build on arches w/o ioremap
staging: r8712u: Use asynchronous firmware loading
staging: usbip: fix to prevent potentially using uninitialized spinlock
staging: r8712u: Fix problem when CONFIG_R8712_AP is set
staging: tidspbridge: fix incorrect free to drv_datap
staging: tidspbridge: fix bridge_open memory leaks
staging: android: lowmemorykiller: Don't wait more than one second for a process to die
MAINTAINERS: staging: iio: add iio information
staging: zcache: fix serialization bug in zv stats
staging: fix go7007-usb license
Staging: android: binder: Fix crashes when sharing a binder file between processes
Staging: android: Remove pmem driver
Staging: asus_oled: fix NULL-ptr crash on unloading
Staging: asus_oled: fix image processing
Staging: android: binder: Don't call dump_stack in binder_vma_open
staging: r8712u: Add new Sitecom UsB ID
zcache: Set SWIZ_BITS to 8 to reduce tmem bucket lock contention.
zcache: fix deadlock condition
staging: drm/omap: fix locking issue
...
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80J1cACgkQMUfUDdst+ylYfgCcClIeUw4njh3Tup9BpRrdBprr
fBsAoLKKhaZDsnma85PJRDAvtM2guoi7
=0TZ9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Driver core fixes for the 3.3-rc3 tree.
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: cpu: fix kobject warning when hotplugging a cpu
ACPI: remove duplicated lines of merging problems with acpi_processor_add
docbook: fix fatal errors in device-drivers docbook and add DMA Management section
drivers/base/memory.c: fix memory_dev_init() long delay
driver core: cpu: remove kernel warning when removing a cpu
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80HSAACgkQMUfUDdst+ymFsQCghwKbV9B9z5fgUXYwFQJ/pD2j
GhsAn3J2mhhHN/vtSPQAN9Vu59Xb/tCi
=VZaE
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Minor char-misc fixes for 3.3-rc3
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mmc: cb710 core: Add missing spin_lock_init for irq_lock of struct cb710_chip
cs5535-mfgpt: don't call __init function from __devinit
vmw_balloon: fix for a -Wuninitialized warning
drivers: misc: Remove MISC_DEVICES config option
c2port: fix build error for duramar2150 due to missing header.
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80Ki4ACgkQMUfUDdst+ymp3wCfUG2LtQOC2qpzpnl1bcivSA18
11gAn09DbcldfH4k12HyCr7PuBnjILQh
=vfEv
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB fixes for 3.3-rc3
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbserial: add new PID number (0xa951) to the ftdi driver
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
usb: musb: fix a build error on mips
uwb & wusb & usb wireless controllers: fix kconfig error & build errors
usb: Skip PCI USB quirk handling for Netlogic XLP
powerpc/usb: fix issue of CPU halt when missing USB PHY clock
usb: otg: mv_otg: Add dependence
usb: host: Distinguish Kconfig text for Freescale controllers
USB: add new zte 3g-dongle's pid to option.c
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
USB: qcserial: don't enable autosuspend
USB: qcserial: add several new serial devices
usb: otg: mv_otg: Add dependence
usb: gadget: zero: fix bug in loopback autoresume handling
The current error handling doesn't work because we flash_part is a u32
so the checks for negative error codes don't work. I considered making
things signed but I don't know the hardware enough to say if that's a
problem. Really, we don't use the error codes so just returning zero
for all problems is fine.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use len to store the return value from eth_header(). eth_header()
can return -ETH_HLEN (-14). We want to pass this back instead of
truncating it to 65522 and returning that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat pwmX as a measured value, not as a (mostly static) limit value, so
that it is updated more frequently from the device register.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The receive FIFO wakeup latency estimate in the omap-serial driver is
three orders of magnitude too small. This effectively prevents the
MPU from going to a low-power state when CONFIG_CPU_IDLE=y. This is a
major power management regression and masks some other FIFO-related
bugs in the driver.
Fix by correcting the most egregious problem in the RX wakeup latency
estimate. There are several other flaws in the estimator; these will
be fixed by a separate patch series intended for 3.4.
The difference in low-power states with this patch can be observed via
debugfs in pm_debug/count.
This estimate does not have any effect when CONFIG_CPU_IDLE=n.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
