Add main code for internal abort functionality.
The internal abort features allows the host controller to abort commands
which are still active in the controller but have not yet been sent to
the slave device.
Typically a command only spends a relatively short time in the
controller when compared to the amount of the time after it is sent to
the slave device.
Two modes of internal abort are supported:
- device
- individual command
For device, when the internal abort is issued all commands in the host
for that device are aborted. For a single command, only that command is
aborted if it is still in the host.
In HW the internal abort command is executed similar to any other sort
of command, like SSP.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
req_table is allocate by kzalloc, so we don't need to zero it again.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We don't need to use kzalloc as we will always memset the
local_atto_ioctl later.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current EQ delay is set to 0 to receive very high max interrupt per sec.
Set EQ delay to 32 - reducing max interrupt rate from 65K to 20K per sec.
Set TCP connection window size to 64K with scale shift count 2.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In very rare scenario, connection gets killed after throwing this error:
scsi host0: BM_2312 : Event CXN_KILLED_BAD_WRB_INDEX_ERROR[15]... CID : 4
connection1:0: detected conn error (1011)
memset ISCSI_WRB descriptor to zero for all allocations of WRB handle.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BUG: unable to handle kernel NULL pointer dereference at 000000000000015e
IP: [<ffffffffa0081700>]
hwi_get_async_handle.isra.23.constprop.39+0x90/0x1d0 [be2iscsi]
PGD 0
Oops: 0000 [#1] SMP
...
Call Trace:
<IRQ>
[<ffffffffa00818bc>] hwi_process_default_pdu_ring+0x7c/0x280 [be2iscsi]
[<ffffffffa0088f51>] beiscsi_process_cq+0x321/0xb90 [be2iscsi]
[<ffffffff810af028>] ? __wake_up_common+0x58/0x90
[<ffffffff810b0d84>] ? __wake_up+0x44/0x50
[<ffffffffa0089a2d>] be_iopoll+0x1d/0xb0 [be2iscsi]
[<ffffffff812d1f61>] blk_iopoll_softirq+0xc1/0x100
[<ffffffff81084b0f>] __do_softirq+0xef/0x280
The symptom observed is multiple async handles get queued for same index
thus causing leak in buffers posted to FW.
The root cause is:
- async handle is continued to be used even if it does not match the
completion.
- list_move operation done on already filled index.
1. Remove use of writables, host_write_ptr and ep_read_ptr.
2. Remove consumed logic to update writables. Instead, use only
free_entries to do the accounting of handles to be posted back.
3. Remove busy_list, instead use simple slot to index handles.
4. Added check no data, header less and overflow to make sure
all async_handles are flushed in error cases.
5. Added code to verify gathering of handles to form PDU by
checking final bit before forwarding PDU.
6. Added code to catch mismatch with CQE and handle gracefully.
7. Use AMAP, traverse cri_wait_queue list to post buffers, log
"async PDU" related errors.
8. Rearranged few data structures and added comments in init &
processing path.
9. Added WARN_ONs to catch any HD ring corruption.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver unload should call COMMON_FUNCTION_RESET. For TPE feature, this
ensures that FW has knowledge about driver getting unloaded and can
reset its bit vector.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sessions are no longer valid, so schedule sess_work to fail the sessions
immediately when error is detected. This is done to avoid iSCSI transport
layer to keep sending NOP-Out which driver any ways fail.
Schedule sess_work immediately in case of HBA error. Old sessions are gone
for good and need to be re-established.
iscsi_session_failure needs process context hence this work.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After UE is detected, check for recoverable error by reading
SLIPORT SEMAPHORE register. If transient parity error i.e. 0xExxx
then schedule recovery work on driver wq.
FLag this error to prevent any transactions for the duration of ue2rp to
restart polling. After that, if FW becomes ready then recover port.
Wake up processes in wq before going offline.
Wait for process to execute before cleaning up.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
mgmt_epfw_cleanup does not implement v1 of OPCODE_COMMON_ISCSI_CLEANUP
IOCTL for SkyHawk.
Replace use of MCCQ with BMBX for issuing the IOCTL.
Remove be_mcc_compl_poll which is no longer needed.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SLIPORT FUNCTION_RESET does not reset the chip.
So POST status needs to be checked before issuing FUNCTION_RESET.
The completion of FUNCTION_RESET is indicated in BMBX Rdy bit.
be_cmd_fw_initialize too needs to be done before issuing any cmd to FW.
be_cmd_fw_initialize is renamed as beiscsi_cmd_special_wrb.
Rearrange and rename few functions in init and cleanup path.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
beiscsi_fail_session is defined in be_cmds.c: move it to be_iscsi.c
Move card configuration commands to be_cmds.c.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BE3 and SH cards can recover from transient parity errors treated
earlier as unrecoverable errors.
Add IOCTL to query FW support for this feature.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UE detection in health check is done in a work scheduled in global wq.
UE caused due to transient parity errors are recoverable and reported
within 1s. If this check for TPE gets delayed, PF0 might initiate
soft-reset and then status of UE recoverable is lost.
Handle UE detection in timer routine. Move out EQ delay update work
from health check. Make the IOCTL for EQ delay update non-blocking
as the completion status is ignored.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Boot work involves:
1. Find and fetch configured boot session and its handle.
2. Attempt to open the session if its not.
3. Get the session details for boot kset creation.
4. Logout of that session owned by FW.
5. Create boot kset for session details.
All these actions were done in blocking call with retries in global wq.
Other works in wq suffered if the IOCTLs stalled or timed out.
This change moves all the boot work to make it non-blocking.
The work queued in global wq just issues the IOCTL depending on the action
to be taken and mcc wq schedules work depending on status of the IOCTL.
Initial boot_work is started on link and ASYNC event.
The other code changes move all boot related functions in one place and
follow naming conventions.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Save ue_detected and fw_timeout errors in state field of beiscsi_hba.
BEISCSI_HBA_RUNNING
BEISCSI_HBA_LINK_UP
BEISCSI_HBA_BOOT_FOUND
BEISCSI_HBA_PCI_ERR
BEISCSI_HBA_FW_TIMEOUT
BEISCSI_HBA_IN_UE
Make sure no PCI transaction happens once in error state.
Add checks in IO path to detect HBA in error.
Skip hwi_purge_eq step which can't be done in error state.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
todo_mcc_cq is not needed as only MCC work is queued.
todo_cq is not used at all.
Rename functions to be consistent.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
alloc_mcc_tag was replaced with alloc_mcc_wrb and is no more used.
beiscsi_pci_soft_reset is not used at all and won't be needed.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Redefine FW IP types.
Before issuing IOCTL to clear IP, check if IP is all zeroes.
All zeroes IP implies IP is not set in FW so FW fails that IOCTL.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Wrong settings displayed for iface:
iface.header_digest = 192.168.197.22
iface.data_digest = 255.255.255.0
iface.immediate_data = 192.168.197.1
Process ISCSI_NET_PARAM only in beiscsi_iface_get_param.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename mgmt_get_if_info to be consistent with APIs name.
Rename create/destroy APIs to indicate IFACE operations.
Remove legacy be2iscsi and use beiscsi.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move mgmt_get_all_if_id before any set param operation.
Rename mgmt_get_all_if_id to beiscsi_if_get_handle.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
VLAN tag is L2 construct, move VLAN code out from configuring IP.
Rearrange and rename the APIs to make it consistent.
Replace ENOSYS with EPERM.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If BOOTPROTO is changed to static, the DHCP IP address should be released.
All cases are being handled mgmt_set_ip and mgmt_static_ip_modify.
Rearrange IFACE APIs to:
beiscsi_if_clr_ip
beiscsi_if_set_ip
beiscsi_if_en_static
beiscsi_if_en_dhcp
This simplifies release of DHCP IP when BOOTPROTO is set to static.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gateway APIs assume IP type as IPv4. Modify it to be generic to allow
clearing of IPv6 gateway set using BIOS.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ipv4_iface and ipv6_iface fields need to be set to NULL when destroyed.
Before creation these are checked. Use these to report correct states.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver takes significant time to load 1m:20s and unload 40s.
Checkpatch script threw warning:
WARNING: msleep < 20ms can sleep for up to 20ms; see
Documentation/timers/timers-howto.txt
To eliminate this warning msleep(1) was replaced with msleep(20) before
submitting.
msleep(20) in init and uninit path for creation and destroying of number
of WRBQs, CQs, and EQs is adding to load/unload time.
Replace msleep with schedule_timeout_uninterruptible of 1ms as its
enough in most cases.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This got unnecessarily introduced with other changes in previous
commits. mcc_lock is taken only in process contexts.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following configuration is created with what driver exports:
iface.vlan_id = 65535
iface.vlan_priority = 255
iface.vlan_state = <empty>
vlan_state is empty as iscsiadm doesn't process "Disabled".
When applying this configuration, iscsiadm checks for if vlan_state is
"disable" if not it enables with value in vlan_id. 65535 not being valid
value, 0 is applied.
Use "enable" or "disable" for ISCSI_NET_PARAM.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter file descriptor was previously cached within the kernel for
a given context in order to support performing a close on behalf of an
application. This is no longer needed as applications are now required
to perform a close on the adapter file descriptor.
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Caching the adapter file descriptor and performing a close on behalf of
an application is a poor design. This is due to the fact that once a
file descriptor in installed, it is free to be altered without the
knowledge of the cxlflash driver. This can lead to inconsistencies
between the application and kernel. Furthermore, the nature of the
former design is more exploitable and thus should be abandoned.
To support applications performing a close on the adapter file that is
associated with a context, a new flag is introduced to the user API to
indicate to applications that they are responsible for the close
following the cleanup (detach) of a context. The documentation is also
updated to reflect this change in behavior.
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, context user references are tracked via the list of LUNs that
have attached to the context. While convenient, this is not intuitive
without a deep study of the code and is inconsistent with the existing
reference tracking patterns within the kernel. This design choice can
lead to future bug injection.
To improve code comprehension and better protect against future bugs,
add explicit reference counting to contexts and migrate the context
removal code to the kref release handler.
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The context removal routine requires access to the owning adapter
structure to reset the context within the AFU as part of the tear down
sequence. In order to support kref adoption, the owning adapter must be
accessible from the release handler. As the kref framework only provides
the kref reference as the sole parameter, another means is needed to
derive the owning adapter.
As a remedy, the owning adapter reference is saved off within the
context during initialization.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Context information structures are protected by a mutex that is held
when accessing/manipulating the context. When the code that manages
these structures was authored, a decision was made to include taking the
mutex as part of the allocation/initialization sequence and also handle
the scenario where the mutex was already held when freeing the context.
While not a problem outright, this design decision has been deemed as
too flexible and the code should be made more rigid to avoid future
bugs. In addition, further review of the code yields that the existing
mutex manipulations in both of these context management paths are
superfluous.
This commit removes the obtaining of the context mutex in the context
initialization routine and assumes the mutex is not held in the context
free path.
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When all exchanges are reset the upper layers have already logged out of
the remote port, so the exchanges can be reset without sending any ABTS.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chad Dupuis <chad.dupuis@qlogic.com>
Tested-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FC-LS mandates that we should invalidate all sequences before sending a
LOGO. And we should set the event to RPORT_EV_STOP when a LOGO request
has been received to signal that all exchanges are terminated.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chad Dupuis <chad.dupuis@qlogic.com>
Tested-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running in point-to-multipoint mode PLOGI is done after FLOGI
completed. So when the PLOGI fails we should be sending a LOGO to the
remote port.
[mkp: Applied by hand]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chad Dupuis <chad.dupuis@qlogic.com>
Tested-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When receiving a PRLO it just means that the operating parameters have
changed, it does _not_ mean that the port doesn't want to communicate
with us. So instead of implicitly logging out we should be issueing a
PRLI to figure out the new operating parameters. We can always recover
once PRLI fails.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chad Dupuis <chad.dupuis@qlogic.com>
Tested-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As there are no more users of is_sas_attached() left, remove it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use scsi_is_sas_rphy() instead of is_sas_attached() to decide whether we
should obtain the SAS address from a scsi device or not. This will
prevent us from tripping on the BUG_ON() in sas_sdev_to_rdev() if the
rphy isn't attached to the SAS transport class, like it is with hpsa's
logical devices.
Fixes: 3f8d6f2a0 ('ses: fix discovery of SATA devices in SAS enclosures')
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
"Universal Xport" LUN is used for in-band storage array management.
Cc: Sean Stewart <Sean.Stewart@netapp.com>
Cc: Christophe Varoqui <christophe.varoqui@opensvc.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Cc: device-mapper development <dm-devel@redhat.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Sean Stewart <Sean.Stewart@netapp.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 655ee63cf3 ("scsi constants: command, sense key + additional
sense string") added a "Completed" sense string with key 0xF to
snstext[], but failed to updated the upper bounds check of the sense key
in scsi_sense_key_string().
Fixes: 655ee63cf3 ("[SCSI] scsi constants: command, sense key + additional sense strings")
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we free the resources backing the enclosure device before we
call device_unregister(). This is racy: during rmmod of low-level SCSI
drivers that hook into enclosure, we end up with a small window of time
during which writing to /sys can OOPS. Example trace with mpt3sas:
general protection fault: 0000 [#1] SMP KASAN
Modules linked in: mpt3sas(-) <...>
RIP: [<ffffffffa0388a98>] ses_get_page2_descriptor.isra.6+0x38/0x220 [ses]
Call Trace:
[<ffffffffa0389d14>] ses_set_fault+0xf4/0x400 [ses]
[<ffffffffa0361069>] set_component_fault+0xa9/0xf0 [enclosure]
[<ffffffff8205bffc>] dev_attr_store+0x3c/0x70
[<ffffffff81677df5>] sysfs_kf_write+0x115/0x180
[<ffffffff81675725>] kernfs_fop_write+0x275/0x3a0
[<ffffffff8151f810>] __vfs_write+0xe0/0x3e0
[<ffffffff8152281f>] vfs_write+0x13f/0x4a0
[<ffffffff81526731>] SyS_write+0x111/0x230
[<ffffffff828b401b>] entry_SYSCALL_64_fastpath+0x13/0x94
Fortunately the solution is extremely simple: call device_unregister()
before we free the resources, and the race no longer exists. The driver
core holds a reference over ->remove_dev(), so AFAICT this is safe.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This initial commit contains Microsemi's smartpqi module.
[mkp: Minor tweaks to apply to 4.9/scsi-queue]
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit b195d5e2bf ("ipr: Wait to do async scan until scsi host is
initialized") fixed async scan for ipr, but broke sync scan. This fixes
sync scan back up.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Found one megaraid_sas HBA probe fails,
[ 187.235190] scsi host2: Avago SAS based MegaRAID driver
[ 191.112365] megaraid_sas 0000:89:00.0: BAR 0: can't reserve [io 0x0000-0x00ff]
[ 191.120548] megaraid_sas 0000:89:00.0: IO memory region busy!
and the card has resource like,
[ 125.097714] pci 0000:89:00.0: [1000:005d] type 00 class 0x010400
[ 125.104446] pci 0000:89:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 125.110686] pci 0000:89:00.0: reg 0x14: [mem 0xce400000-0xce40ffff 64bit]
[ 125.118286] pci 0000:89:00.0: reg 0x1c: [mem 0xce300000-0xce3fffff 64bit]
[ 125.125891] pci 0000:89:00.0: reg 0x30: [mem 0xce200000-0xce2fffff pref]
that does not io port resource allocated from BIOS, and kernel can not
assign one as io port shortage.
The driver is only looking for MEM, and should not fail.
It turns out megasas_init_fw() etc are using bar index as mask. index 1
is used as mask 1, so that pci_request_selected_regions() is trying to
request BAR0 instead of BAR1.
Fix all related reference.
Fixes: b6d5d8808b ("megaraid_sas: Use lowest memory bar for SR-IOV VF support")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In aacraid's ioctl_send_fib() we do two fetches from userspace, one the
get the fib header's size and one for the fib itself. Later we use the
size field from the second fetch to further process the fib. If for some
reason the size from the second fetch is different than from the first
fix, we may encounter an out-of- bounds access in aac_fib_send(). We
also check the sender size to insure it is not out of bounds. This was
reported in https://bugzilla.kernel.org/show_bug.cgi?id=116751 and was
assigned CVE-2016-6480.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Fixes: 7c00ffa31 '[SCSI] 2.6 aacraid: Variable FIB size (updated patch)'
Cc: stable@vger.kernel.org
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "if (test_bit(UNLOADING..." line was indented one tab more than it
should have been. There was an extra parenthesis around the
qla2x00_reset_active() function call. I lined up the conditions a bit
so that it shows how they group together.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _scsih_io_done() we test if the ioc->logging_level does _not_ have
the MPT_DEBUG_REPLY bit set and if it hasn't we print the debug
messages. This unfortunately is the wrong way around.
Note, the actual bug is older than af0094115 but this commit removed the
CONFIG_SCSI_MPT3SAS_LOGGING Kconfig option which hid the bug.
Fixes: af0094115 'mpt2sas, mpt3sas: Remove SCSI_MPTXSAS_LOGGING entry from Kconfig'
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial non-functional changes for a couple annoying things:
1) Functions local to files are not declared static, which is
frustrating when reading the code because it's non-obvious at first
glance what's actually called from other files.
2) Set-but-unused variables abound, presumably to mask -Wunused-result
errors in the past. None of these are flagged today though (with one
exception noted below), so remove them.
Fixing (2) exposed the fact that we improperly ignore the return value
of scsi_device_reprobe() in _scsih_reprobe_lun(). Fixing the calling
code to deal with the potential error is non-trivial, so for now just
WARN().
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With the exception of a single call to wait_for_doorbell_int(), all this
conditional sleeping code is dead. So delete it.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This flag that conditionally acquires the mutex is confusing and prone
to bugginess: refactor it into two separate function calls, and make the
unlocked one complain if it's called outside the mutex.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We blindly trust the hardware to give us NUL-terminated strings, which
is a bad idea because it doesn't always do that. For example:
[ 481.184784] mpt3sas_cm0: enclosure level(0x0000), connector name( \x3)
In this case, connector_name is four spaces. We got lucky here because
the 2nd byte beyond our character array happens to be a NUL. Fix this by
explicitly writing '\0' to the end of the string to ensure we don't run
off the edge of the world in printk().
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is seven basic fixes (plus one MAINTAINER update) which came in
close to the merge window.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=826r
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is seven basic fixes (plus one MAINTAINER update) which came in
close to the merge window"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ipr: Fix error return code in ipr_probe_ioa()
fcoe: add missing destroy_workqueue() on error in fcoe_init()
lpfc: Fix possible NULL pointer dereference
fcoe: Use default VLAN for FIP VLAN discovery
ipr: Wait to do async scan until scsi host is initialized
MAINTAINERS: Update cxlflash maintainers
cxlflash: Verify problem state area is mapped before notifying shutdown
lpfc: fix oops in lpfc_sli4_scmd_to_wqidx_distr() from lpfc_send_taskmgmt()
Use kfree_skb() instead of kfree() to free sk_buff.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull SCSI target updates from Nicholas Bellinger:
"The most notable item is IBM virtual SCSI target driver, that was
originally ported to target-core back in 2010 by Tomo-san, and has
been brought forward to v4.x code by Bryant Ly, Michael Cyr and co
over the last months.
Also included are two ORDERED task related bug-fixes Bryant + Michael
found along the way using ibmvscsis with AIX guests, plus a few
miscellaneous target-core + iscsi-target bug-fixes with associated
stable tags"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: fix spelling mistake: "limitiation" -> "limitation"
target: Fix residual overflow handling in target_complete_cmd_with_length
tcm_fc: set and unset FCP_SPPF_TARG_FCN
iscsi-target: Fix panic when adding second TCP connection to iSCSI session
ibmvscsis: Initial commit of IBM VSCSI Tgt Driver
target: Fix ordered task CHECK_CONDITION early exception handling
target: Fix ordered task target_setup_cmd_from_cdb exception hang
target: Fix max_unmap_lba_count calc overflow
target: Fix race between iscsi-target connection shutdown + ABORT_TASK
target: Fix missing complete during ABORT_TASK + CMD_T_FABRIC_STOP
Fix to return error code -ENOMEM from the workqueue alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the missing destroy_workqueue() before return from fcoe_init() in
the fcoe transport register failed error handling case.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check for the existence of piocb->vport before accessing it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
This update includes the usual round of driver updates (fcoe, lpfc,
ufs, qla2xxx, hisi_sas). The most important other change is removing
the flag to allow non-blk_mq on a per host basis (it's unused); there
is still a global module parameter for all of SCSI just in case. The
rest are an assortment of minor fixes and typo updates.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vRgI
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of driver updates (fcoe, lpfc,
ufs, qla2xxx, hisi_sas). The most important other change is removing
the flag to allow non-blk_mq on a per host basis (it's unused); there
is still a global module parameter for all of SCSI just in case.
The rest are an assortment of minor fixes and typo updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (101 commits)
scsi:libsas: fix oops caused by assigning a freed task to ->lldd_task
fnic: pci_dma_mapping_error() doesn't return an error code
scsi: lpfc: avoid harmless comparison warning
fcoe: implement FIP VLAN responder
fcoe: Rename 'fip_frame' to 'fip_vn2vn_notify_frame'
lpfc: call lpfc_sli_validate_fcp_iocb() with the hbalock held
scsi: ufs: remove unnecessary goto label
hpsa: change hpsa_passthru_ioctl timeout
hpsa: correct skipping masked peripherals
qla2xxx: Update driver version to 8.07.00.38-k
qla2xxx: Fix BBCR offset
qla2xxx: Fix duplicate message id.
qla2xxx: Disable the adapter and skip error recovery in case of register disconnect.
qla2xxx: Separate ISP type bits out from device type.
qla2xxx: Correction to function qla26xx_dport_diagnostics().
qla2xxx: Add support to handle Loop Init error Asynchronus event.
qla2xxx: Let DPORT be enabled purely by nvram.
qla2xxx: Add bsg interface to support statistics counter reset.
qla2xxx: Add bsg interface to support D_Port Diagnostics.
qla2xxx: Check for device state before unloading the driver.
...
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
FC-BB-6 states: FIP protocols shall be performed on a per-VLAN basis. It
is recommended to use the FIP VLAN discovery protocol on the default
VLAN.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When performing an async scan, make sure the kthread doing scanning
doesn't start before the scsi host is fully initialized.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an EEH or some other hard error occurs while the adapter instance was
being initialized, on the subsequent shutdown of the device, the system
could crash with:
[c000000f1da03b60] c0000000005eccfc pci_device_shutdown+0x6c/0x100
[c000000f1da03ba0] c0000000006d67d4 device_shutdown+0x1b4/0x2c0
[c000000f1da03c40] c0000000000ea30c kernel_restart_prepare+0x5c/0x80
[c000000f1da03c70] c0000000000ea48c kernel_restart+0x2c/0xc0
[c000000f1da03ce0] c0000000000ea970 SyS_reboot+0x1c0/0x2d0
[c000000f1da03e30] c000000000009204 system_call+0x38/0xb4
This crash is due to the AFU not being mapped when the shutdown
notification routine is called and is a regression that was inserted
recently with Commit 704c4b0ddc ("cxlflash: Shutdown notify support
for CXL Flash cards").
As a fix, shutdown notification should only occur when the AFU is
mapped.
Fixes: 704c4b0ddc ("cxlflash: Shutdown notify support for CXL Flash cards")
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
later merged with 'for-4.8/core' to pickup the QUEUE_FLAG_DAX commits
that DM depends on to provide its DAX support
- clean up the bio-based vs request-based DM core code by moving the
request-based DM core code out to dm-rq.[hc]
- reinstate bio-based support in the DM multipath target (done with the
idea that fast storage like NVMe over Fabrics could benefit) -- while
preserving support for request_fn and blk-mq request-based DM mpath
- SCSI and DM multipath persistent reservation fixes that were
coordinated with Martin Petersen.
- the DM raid target saw the most extensive change this cycle; it now
provides reshape and takeover support (by layering ontop of the
corresponding MD capabilities)
- DAX support for DM core and the linear, stripe and error targets
- A DM thin-provisioning block discard vs allocation race fix that
addresses potential for corruption
- A stable fix for DM verity-fec's block calculation during decode
- A few cleanups and fixes to DM core and various targets
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXkRZmAAoJEMUj8QotnQNat2wH/i4LpkoGI5tI6UhyKWxRkzJp
vKaJ0zuZ2Ez73DucJujNuvaiyHq1IjHD5pfr8JQO3E8ygDkRC2KjF2O8EXp0Has6
U1uLahQej72MAs0ZJTpvfE+JiY6qyIl4K+xxuPmYm2f2S5TWTIgOetYjJQmcMlQo
Y8zFfcDYn4Dv5rMdvDT4+1ePETxq74wcBwTxyW3OAbHE1f0JjsUGdMKzXB1iTWcM
VjLjWI//ETfFdIlDO0w2Qbd90aLUjmTR2k67RGnbPj5kNUNikv/X6iiY32KERR/0
vMiiJ7JS+a44P7FJqCMoAVM/oBYFiSNpS4LYevOgHb0G0ikF8kaSeqBPC6sMYvg=
=uYt9
-----END PGP SIGNATURE-----
Merge tag 'dm-4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- initially based on Jens' 'for-4.8/core' (given all the flag churn)
and later merged with 'for-4.8/core' to pickup the QUEUE_FLAG_DAX
commits that DM depends on to provide its DAX support
- clean up the bio-based vs request-based DM core code by moving the
request-based DM core code out to dm-rq.[hc]
- reinstate bio-based support in the DM multipath target (done with the
idea that fast storage like NVMe over Fabrics could benefit) -- while
preserving support for request_fn and blk-mq request-based DM mpath
- SCSI and DM multipath persistent reservation fixes that were
coordinated with Martin Petersen.
- the DM raid target saw the most extensive change this cycle; it now
provides reshape and takeover support (by layering ontop of the
corresponding MD capabilities)
- DAX support for DM core and the linear, stripe and error targets
- a DM thin-provisioning block discard vs allocation race fix that
addresses potential for corruption
- a stable fix for DM verity-fec's block calculation during decode
- a few cleanups and fixes to DM core and various targets
* tag 'dm-4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (73 commits)
dm: allow bio-based table to be upgraded to bio-based with DAX support
dm snap: add fake origin_direct_access
dm stripe: add DAX support
dm error: add DAX support
dm linear: add DAX support
dm: add infrastructure for DAX support
dm thin: fix a race condition between discarding and provisioning a block
dm btree: fix a bug in dm_btree_find_next_single()
dm raid: fix random optimal_io_size for raid0
dm raid: address checkpatch.pl complaints
dm: call PR reserve/unreserve on each underlying device
sd: don't use the ALL_TG_PT bit for reservations
dm: fix second blk_delay_queue() parameter to be in msec units not jiffies
dm raid: change logical functions to actually return bool
dm raid: use rdev_for_each in status
dm raid: use rs->raid_disks to avoid memory leaks on free
dm raid: support delta_disks for raid1, fix table output
dm raid: enhance reshape check and factor out reshape setup
dm raid: allow resize during recovery
dm raid: fix rs_is_recovering() to allow for lvextend
...
Pull block driver updates from Jens Axboe:
"This branch also contains core changes. I've come to the conclusion
that from 4.9 and forward, I'll be doing just a single branch. We
often have dependencies between core and drivers, and it's hard to
always split them up appropriately without pulling core into drivers
when that happens.
That said, this contains:
- separate secure erase type for the core block layer, from
Christoph.
- set of discard fixes, from Christoph.
- bio shrinking fixes from Christoph, as a followup up to the
op/flags change in the core branch.
- map and append request fixes from Christoph.
- NVMeF (NVMe over Fabrics) code from Christoph. This is pretty
exciting!
- nvme-loop fixes from Arnd.
- removal of ->driverfs_dev from Dan, after providing a
device_add_disk() helper.
- bcache fixes from Bhaktipriya and Yijing.
- cdrom subchannel read fix from Vchannaiah.
- set of lightnvm updates from Wenwei, Matias, Johannes, and Javier.
- set of drbd updates and fixes from Fabian, Lars, and Philipp.
- mg_disk error path fix from Bart.
- user notification for failed device add for loop, from Minfei.
- NVMe in general:
+ NVMe delay quirk from Guilherme.
+ SR-IOV support and command retry limits from Keith.
+ fix for memory-less NUMA node from Masayoshi.
+ use UINT_MAX for discard sectors, from Minfei.
+ cancel IO fixes from Ming.
+ don't allocate unused major, from Neil.
+ error code fixup from Dan.
+ use constants for PSDT/FUSE from James.
+ variable init fix from Jay.
+ fabrics fixes from Ming, Sagi, and Wei.
+ various fixes"
* 'for-4.8/drivers' of git://git.kernel.dk/linux-block: (115 commits)
nvme/pci: Provide SR-IOV support
nvme: initialize variable before logical OR'ing it
block: unexport various bio mapping helpers
scsi/osd: open code blk_make_request
target: stop using blk_make_request
block: simplify and export blk_rq_append_bio
block: ensure bios return from blk_get_request are properly initialized
virtio_blk: use blk_rq_map_kern
memstick: don't allow REQ_TYPE_BLOCK_PC requests
block: shrink bio size again
block: simplify and cleanup bvec pool handling
block: get rid of bio_rw and READA
block: don't ignore -EOPNOTSUPP blkdev_issue_write_same
block: introduce BLKDEV_DISCARD_ZERO to fix zeroout
NVMe: don't allocate unused nvme_major
nvme: avoid crashes when node 0 is memoryless node.
nvme: Limit command retries
loop: Make user notify for adding loop device failed
nvme-loop: fix nvme-loop Kconfig dependencies
nvmet: fix return value check in nvmet_subsys_alloc()
...
Pull core block updates from Jens Axboe:
- the big change is the cleanup from Mike Christie, cleaning up our
uses of command types and modified flags. This is what will throw
some merge conflicts
- regression fix for the above for btrfs, from Vincent
- following up to the above, better packing of struct request from
Christoph
- a 2038 fix for blktrace from Arnd
- a few trivial/spelling fixes from Bart Van Assche
- a front merge check fix from Damien, which could cause issues on
SMR drives
- Atari partition fix from Gabriel
- convert cfq to highres timers, since jiffies isn't granular enough
for some devices these days. From Jan and Jeff
- CFQ priority boost fix idle classes, from me
- cleanup series from Ming, improving our bio/bvec iteration
- a direct issue fix for blk-mq from Omar
- fix for plug merging not involving the IO scheduler, like we do for
other types of merges. From Tahsin
- expose DAX type internally and through sysfs. From Toshi and Yigal
* 'for-4.8/core' of git://git.kernel.dk/linux-block: (76 commits)
block: Fix front merge check
block: do not merge requests without consulting with io scheduler
block: Fix spelling in a source code comment
block: expose QUEUE_FLAG_DAX in sysfs
block: add QUEUE_FLAG_DAX for devices to advertise their DAX support
Btrfs: fix comparison in __btrfs_map_block()
block: atari: Return early for unsupported sector size
Doc: block: Fix a typo in queue-sysfs.txt
cfq-iosched: Charge at least 1 jiffie instead of 1 ns
cfq-iosched: Fix regression in bonnie++ rewrite performance
cfq-iosched: Convert slice_resid from u64 to s64
block: Convert fifo_time from ulong to u64
blktrace: avoid using timespec
block/blk-cgroup.c: Declare local symbols static
block/bio-integrity.c: Add #include "blk.h"
block/partition-generic.c: Remove a set-but-not-used variable
block: bio: kill BIO_MAX_SIZE
cfq-iosched: temporarily boost queue priority for idle classes
block: drbd: avoid to use BIO_MAX_SIZE
block: bio: remove BIO_MAX_SECTORS
...
Pull libata updates from Tejun Heo:
"libata saw quite a bit of activities in this cycle:
- SMR drive support still being worked on
- bug fixes and improvements to misc SCSI command emulation
- some low level driver updates"
* 'for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (39 commits)
libata-scsi: better style in ata_msense_*()
AHCI: Clear GHC.IS to prevent unexpectly asserting INTx
ata: sata_dwc_460ex: remove redundant dev_err call
ata: define ATA_PROT_* in terms of ATA_PROT_FLAG_*
libata: remove ATA_PROT_FLAG_DATA
libata: remove ata_is_nodata
ata: make lba_{28,48}_ok() use ATA_MAX_SECTORS{,_LBA48}
libata-scsi: minor cleanup for ata_scsi_zbc_out_xlat
libata-scsi: Fix ZBC management out command translation
libata-scsi: Fix translation of REPORT ZONES command
ata: Handle ATA NCQ NO-DATA commands correctly
libata-eh: decode all taskfile protocols
ata: fixup ATA_PROT_NODATA
libsas: use ata_is_ncq() and ata_has_dma() accessors
libata: use ata_is_ncq() accessors
libata: return boolean values from ata_is_*
libata-scsi: avoid repeated calculation of number of TRIM ranges
libata-scsi: reject WRITE SAME (16) with n_block that exceeds limit
libata-scsi: rename ata_msense_ctl_mode() to ata_msense_control()
libata-scsi: fix D_SENSE bit relection in control mode page
...
Fix following sparse warnings
warning: symbol 'cxgb3i_ofld_init' was not declared. Should it be static?
warning: symbol 'cxgb4i_cplhandlers' was not declared. Should it be static?
warning: symbol 'cxgb4i_ofld_init' was not declared. Should it be static?
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export cxgbi_ppm_release() to release
ppod manager and cxgbi_tagmask_set() to
set tag mask, they are used by cxgb3i, cxgb4i
and cxgbit.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add iSCSI DDP support in cxgb3i driver
using common iSCSI DDP Page Pod Manager.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add iSCSI DDP support in cxgb4i driver
using common iSCSI DDP Page Pod Manager.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove old ddp code from cxgb3i,cxgb4i,libcxgbi.
Next two commits adds DDP support using
common iSCSI DDP Page Pod Manager.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A freed task has been assigned to ->lldd_task when lldd_execute_task()
failed in sas_ata_qc_issue(), and access of ->lldd_task will cause an
oops:
Call trace:
[<ffffffc000641f64>] sas_ata_post_internal+0x6c/0x150
[<ffffffc0006c0d64>] ata_exec_internal_sg+0x32c/0x588
[<ffffffc0006c1048>] ata_exec_internal+0x88/0xe8
[<ffffffc0006c13b4>] ata_dev_read_id+0x204/0x5e0
[<ffffffc0006c17f0>] ata_dev_reread_id+0x60/0xc8
[<ffffffc0006c3098>] ata_dev_revalidate+0x88/0x1e0
[<ffffffc0006cf828>] ata_eh_recover+0xcf8/0x13a8
[<ffffffc0006d075c>] ata_do_eh+0x5c/0xe0
[<ffffffc0006d0828>] ata_std_error_handler+0x48/0x98
[<ffffffc0006d042c>] ata_scsi_port_error_handler+0x474/0x658
[<ffffffc000641b78>] async_sas_ata_eh+0x50/0x80
[<ffffffc0000ca664>] async_run_entry_fn+0x64/0x180
[<ffffffc0000c085c>] process_one_work+0x164/0x438
[<ffffffc0000c0c74>] worker_thread+0x144/0x4b0
[<ffffffc0000c70fc>] kthread+0xfc/0x110
Fix this by reassigning NULL to ->lldd_task in error path.
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pci_dma_mapping_error() returns true on error and false on success.
Fixes: fd6ddfa4c1 ('fnic: check pci_map_single() return value')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building with -Wextra, we get a lot of warnings for the lpfc driver
concerning expressions that are always true, starting with:
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_enable_npiv_init':
drivers/scsi/lpfc/lpfc_attr.c:2786:77: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_enable_rrq_init':
drivers/scsi/lpfc/lpfc_attr.c:2802:76: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_suppress_link_up_init':
drivers/scsi/lpfc/lpfc_attr.c:2812:2050: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_log_verbose_init':
drivers/scsi/lpfc/lpfc_attr.c:3064:1930: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
The code works as intended, but it would be nice to shut up the warning
so we don't clutter up build logs with this. Using a separate inline
function for it makes it clear to the compiler that the comparison is
necessary in the caller but still lets it do the constant-folding.
[mkp: fix typo]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running in VN2VN mode there is no central instance which would send
out any FIP VLAN discovery notifications. So this patch adds a new sysfs
attribute 'fip_vlan_responder' which will activate a FIP VLAN discovery
responder.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do not use a generic name to avoid confusions with other usages.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Call lpfc_sli_validate_fcp_iocb() with the hbalock held, as the pointer
to iocbq is not guaranteed to still be valid after looking it up.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I wish the OSD code could simply use blk_rq_map_* helpers like
everyone else, but the complex nature of deciding if we have
DATA IN and/or DATA OUT buffers might make this impossible
(at least for a mere human like me).
But using blk_rq_append_bio at least allows sharing the setup code
between request with or without dat a buffers, and given that this
is the last user of blk_make_request it allows getting rid of that
somewhat awkward interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Boaz Harrosh <ooo@electrozaur.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This driver is a pick up of the old IBM VIO scsi Target Driver
that was started by Nick and Fujita 2-4 years ago.
http://comments.gmane.org/gmane.linux.scsi/90119
The driver provides a virtual SCSI device on IBM Power Servers.
This patch contains the fifth version for an initial merge of the
tcm ibmvscsis driver. More information on this driver and config
can be found:
https://github.com/powervm/ibmvscsis/wiki/Configurationhttp://www.linux-iscsi.org/wiki/IBM_vSCSI
(Drop extra libsrp review breakage + Fix kconfig typo - nab)
Signed-off-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: FUJITA Tomonori <tomof@acm.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the CXL_KERNEL_API and CXL_EEH Kconfig options, as they were only
needed to coordinate the merging of the cxlflash driver. Also remove the
stub implementation of cxl_perst_reloads_same_image() in cxlflash which is
only used if CXL_EEH isn't defined (i.e. never).
Suggested-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These only work if the we use the same initiator ID for all path,
which might not be true if we use different protocols, or even just
different HBAs.
Instead dm-mpath will grow support to register all path manually
later in this series.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When buff_ascii kmalloc failed, there is no need to call kfree, it
should return -ENOMEM directly, this patch fixes it.
Signed-off-by: Tiezhu Yang <kernelpatch@126.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Was not alloting for FW Flash times.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SA controller spins down RAID drive spares.
A REGNEWD event causes an inquiry to be sent to all physical
drives. This causes the SA controller to spin up the spare.
The controller suspends all I/O to a logical volume until
the spare is spun up. The spin-up can take over 50 seconds.
This can result in one or both of the following:
- SML sends down aborts and resets to the logical volume
and can cause the logical volume to be off-lined.
- a negative impact on the logical volume's I/O performance
each time a REGNEWD is triggered.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes: 969a619 ("qla2xxx: Add support for buffer to buffer credit value for ISP27XX.")
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If there is error recovery going on due to command timeout and
there is register disconnect, then disable the adapter.
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During hot swap of PCI device, there can be PCI error on device,
during normal driver unload. The race between normal driver unload and
driver unload due to PCI error, can lead to system crash.Fix is to check
if there is unload going on and allow that function to unload the driver.
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Properly initialize IO statistics to avoid initial 0xFFFFFFF (-1) values.
Cleanup/simplify usage of pointer to statistics structure.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When VP decoupling enabled, there could be a window where, FLOGI from initiators
can be dropped before VP0 is enabled, causing link level recovery.
Retry FLOGI to avoid link level recovery.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 11.2.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Copyright updates
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Disable FDMI probing if not connected to a fabric
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct issue with ioremap() call on 32bit kernel
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Re-organize source for easier driver attribute management
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove global lpfc_sli_mode attribute in leiu of per-hba lpfc_sli_mode
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove global lpfc_delay_discovery attribute in leiu of per-hba
lpfc_delay_discovery
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove global lpfc_enable_npiv attribute in leiu of per-hba lpfc_enable_npiv
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct Port reset resulting in FC port going offline
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for XLane LUN priority
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct RDP response Revision location
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Re-organize source for easier device-id management
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct FCOE discovery to avoid loss of storage devices after system reboot
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix SLI mode 2 config failure
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add MDS Diagnostics Support
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add sysfs proc_name support
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reject RDP ELS if port has no login
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct Buffer credit descriptor values in RDP response
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add recovery from adapter parity errors on some SLI4 adapters
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct RDP response sizing issue
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix Transgression Flag of Optical Element descriptor for RDP on Linux
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
My static checker complains that we need to unlock on this path. Seems
true.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We've had scsi-mq for 2.5 years now, so we can remove the unused flag to
disable the code on a per-host basis that was put in for unexpected
emergencies during bringup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code was checking on PA_CONNECTEDRXLANES and PA_CONNECTEDTXLANES
attributes to program the Lane#1 attributes. The correct attributes are
PA_AVAILRXDATALANES and PA_AVAILTXDATALANES respectively.
Signed-off-by: Manjunath M B <manjumb@synopsys.com>
Tested-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The _scsih_pci_mmio_enabled called if scsih_pci_error_detected returns
PCI_ERS_RESULT_CAN_RECOVER, at this point, read/write to the device
still works, no need to reset slot.
Or the mpt3sas_base_map_resources in scsih_pci_slot_reset will fail,
and iounamp ioc->chip, then we will meet issue when read ioc->chip
in mpt3sas_base_get_iocstate from _base_fault_reset_work.
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2xxx first calls request_irq() and then does the setup of the queue
entry data needed in the interrupt handlers in when using MSI-X. This
could lead to a NULL pointer dereference when an IRQ fires between the
request_irq() call and the assignment of the qentry data structure to
the rsp->msix field. A possible case for such a race would be in the
kdump case when the HBA's IRQs are still enabled but the driver is
undergoing a new initialisation and thus is not aware of already
activated IRQs in the HBA.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use accessors instead of the raw protocol value.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[hch: trivial cleanup of the ata_task assignments]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Increase MSIX vectors from 2 to 16 by default.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the appropriate definitions and table entries for new adapters
support.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The field is only used by the 53c700 driver, so move it into the
driver-private device data instead of having it in the common structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was an issue reported by Lucz Geza on Dell Perc 6i. As per issue
reported, megaraid_sas driver goes into an infinite error reporting loop
as soon as there is a change in the status of one of the
arrays (degrade, resync online etc ). Below are the error logs reported
continuously-
Jun 25 08:49:30 ns8 kernel: [ 757.757017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.778017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.799017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.820018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.841018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
This issue is very much specific to controllers which do not support
DCMD- MR_DCMD_PD_LIST_QUERY. In case of any hotplugging/rescanning of
drives, AEN thread will be scheduled by driver and fire DCMD-
MR_DCMD_PD_LIST_QUERY and if this DCMD is failed then driver will fail
this event processing and will not go ahead for further events. This
will cause infinite loop of same event getting retried infinitely and
causing above mentioned logs.
Fix for this problem is: not to fire DCMD MR_DCMD_PD_LIST_QUERY for
controllers which do not support it and send DCMD SUCCESS status to AEN
function so that it can go ahead with other event processing.
Reported-by: Lucz Geza <geza@lucz.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use defines from ethtool for 20Gbit and 40Gbit speeds instead of magic
numbers.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the FIP mode is changed we need to update the multicast addresses
to ensure we get the correct frames.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'->realdev' is always set, so this check is pointless.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The FIP mode is independent on the FIP state machine, so use a separate
enum for that instead of overloading it with state machine values.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update to latest FC-BB-6 draft to include FIP VN2VN VLAN notifications
and additional flags.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the receive path libfc extracts a cpu number from the ox_id in the
fiber channel header and uses that to do a per_cpu_ptr conversion. If,
for some reason, a frame is received with an invalid ox_id, per_cpu_ptr
will return an invalid pointer and the libfc receive path will panic the
system trying to use it.
I'm currently looking at such a case, and I don't yet know why a cpu
number > nr_cpu_ids is appearing in an exchange id. But adding a sanity
check in libfc prevents a system panic, and seems like good idea when
dealing with frames coming in from the network.
Signed-off-by: Chris Leech <cleech@redhat.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver creates its own per-CPU threads which are updated based on
CPU hotplug events. It is also possible to use kworkers and remove some
of the kthread infrastrucure.
The code checked ->thread to decide if there is an active per-CPU
thread. By using the kworker infrastructure this is no longer
possible (or required). The thread pointer is saved in `kthread' instead
of `thread' so anything trying to use thread is caught by the
compiler. Currently only the bnx2fc driver is using struct fcoe_percpu_s
and the kthread member.
After a CPU went offline, we may still enqueue items on the "offline"
CPU. This isn't much of a problem. The work will be done on a random
CPU. The allocated crc_eof_page page won't be cleaned up. It is probably
expected that the CPU comes up at some point so it should not be a
problem. The crc_eof_page memory is released of course once the module
is removed.
This patch was only compile-tested due to -ENODEV.
Cc: Vasu Dev <vasu.dev@intel.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: fcoe-devel@open-fcoe.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If there is a dma mapping error snic kfree()s buf right before printing
it. Change the order to not accidently trip on memory that's not owned
by us anymore.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Narsimhulu Musini <nmusini@cisco.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enabling format checking in dprintk() shows that wd7000_biosparam uses
an incorrect format string for sector_t:
drivers/scsi/wd7000.c: In function 'wd7000_biosparam':
drivers/scsi/wd7000.c:1594:21: error: format '%d' expects argument of type 'int', but argument 3 has type 'sector_t {aka long long unsigned int}' [-Werror=format=]
As sector_t can be 32-bit wide, this adds a cast to 'u64' and prints
that with the correct format. The change to use no_printk() generally
helps with finding this kind of hidden format string bug, and I found
that when building with "-Wextra", which warned about an empty else
clause in
} else
dprintk("ok!\n");
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fc_get_host_stats() function contains a complex conversion from
jiffies to timespec to seconds. As we try to get rid of uses of struct
timespec, we can clean this up and replace it with a simpler
computation.
Simply dividing the difference in jiffies by HZ is not only much more
efficient, it also avoids a problem that causes the
seconds_since_last_reset value to be incorrect if jiffies has overrun
since the 'boot_time' value was recorded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When enabling the debug options NCR_700_DEBUG and NCR_700_TAG_DEBUG
various printk format warnings can be seen like:
drivers/scsi/53c700.c:357:2: warning: format %p expects argument of type void * , but argument 4 has type dma_addr_t [-Wformat=]
script_patch_32(hostdata->dev, script, MessageLocation,
Fix them by using the right printk format specifiers.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some CXL Flash cards need notification of device shutdown in order to
flush pending I/Os.
A PCI notification hook for shutdown has been added where the driver
notifies the card and returns. When the device is removed in the PCI
remove path, notification code will wait for shutdown processing to
complete.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Device dependent flags are needed to support functions that are specific
to a particular device.
One such case is - some CXL Flash cards need to be notified of device
shutdown. For other CXL devices, this feature does not prove to be
useful yet. Such distinct features need to be identified in the driver
to bypass or invoke specific functionality.
In this patch, a member 'flags' has been added to device dependent
values. These flags will be used and expanded in the future to support
various device specific functions.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While running 'sg_reset -H' in a loop with a user-space application active,
hit the following exception:
cpu 0x2: Vector: 300 (Data Access)
pc: : afu_attach+0x50/0x240 [cxlflash]
lr: : cxlflash_afu_recover+0x3dc/0x7d0 [cxlflash]
pid = 20365, comm = run_block_fvt
Linux version 4.5.0-491-26f710d+
cxlflash_afu_recover+0x3dc/0x7d0 [cxlflash]
cxlflash_ioctl+0x5a8/0x6f0 [cxlflash]
scsi_ioctl+0x3b0/0x4c0
sd_ioctl+0x110/0x190
blkdev_ioctl+0x28c/0xc20
block_ioctl+0xa4/0xd0
do_vfs_ioctl+0xd8/0x8c0
SyS_ioctl+0xd4/0xf0
system_call+0x38/0xb4
The problem here is that the problem space area is unmapped while the
application issues the DK_CXLFLASH_RECOVER_AFU ioctl.
This is the order I observe:
proc1 proc2
1) sg_reset
2) ioctl(DK_CXLFLASH_RECOVER_AFU)
3) sg_reset again
causing a PSA unmap
4) continues RECOVER_AFU processing
The resolution to this problem is to have the reset handler drain all
outstanding user space initiated ioctls before proceeding. It is safe
to drain after the state has been changed to STATE_RESET. Also since
drain_ioctls() was static, it had to be moved up a bit to be before
cxlflash_eh_host_reset_handler().
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In this post: http://www.spinics.net/lists/linux-scsi/msg97124.html the
author shows some kernel infrastructure complaining about a sleep in an
invalid context. Remove offending call to vmalloc(). Instead of using
kzalloc() which reviewers didn't like, use a bucket system (64 bytes on
the stack) and potentially multiple calls to sg_pcopy_from_buffer() to
construct the 'data-in' buffer for the SCSI REPORT LUNS command.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Originally libfc would just be initializing the refcount to '1', and
using the disc_mutex to synchronize if and when the final put should be
happening. This has a race condition as the mutex might be delayed,
causing other threads to access an invalid structure. This patch
updates the rport reference counting to increase the reference every
time 'rport_lookup' is called, and decreases the reference
correspondingly. This removes the need to hold 'disc_mutex' when
removing the structure, and avoids the above race condition.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix build when CONFIG_ISA_DMA_API is not enabled. Fixes these build
errors (on x86_64):
../drivers/scsi/ultrastor.c: In function 'ultrastor_14f_detect':
../drivers/scsi/ultrastor.c:519:5: error: implicit declaration of function 'request_dma' [-Werror=implicit-function-declaration]
if (config.dma_channel && request_dma(config.dma_channel,"Ultrastor")) {
^
../drivers/scsi/ultrastor.c: In function 'ultrastor_release':
../drivers/scsi/ultrastor.c:658:3: error: implicit declaration of function 'free_dma' [-Werror=implicit-function-declaration]
free_dma(shost->dma_channel);
^
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in printk message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support in v2 hw driver for ACPI.
A check on whether an ACPI handle is available for the device is used to
decide on whether to use ACPI reset handler or syscon for hw reset.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a virtual scsi DVD device is present with no image file
attached the storvsc driver logs all resulting unnecessary sense errors
whenever IO is issued to the device.
[storvsc] Sense Key : Not Ready [current]
[storvsc] Add. Sense: Medium not present - tray closed
[mkp: Fixed whitespace]
Signed-off-by: Cathy Avery <cavery@redhat.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "fcp_rsp_code = %d" message isn't an error, it's meant to be
informative only. This patch prevents a flood of such messages in some
situations.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If _scsih_sas_host_add's call to mpt3sas_config_get_sas_iounit_pg0
fails, ioc->sas_hba.parent_dev may be left uninitialized. A later
device probe could invoke mpt3sas_transport_port_add which will call
sas_port_alloc_num [scsi_transport_sas] with a NULL parent_dev pointer.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _scsih_sas_host_add, the number of HBA phys are determined and then
later used to allocate an array of struct _sas_phy's. If the routine
sets ioc->sas_hba.num_phys, but then fails to allocate the
ioc->sas_hba.phy array (by kcalloc error or other intermediate
error/exit path), ioc->sas_hba is left in a dangerous state: all readers
of ioc->sas_hba.phy[] do so by indexing it from 0..ioc->sas_hba.num_phys
without checking that the space was ever allocated.
Modify _scsih_sas_host_add to set ioc->sas_hba.num_phys only after
successfully allocating ioc->sas_hba.phy[].
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds license info to the tc-dwc-g210 and ufshcd-dwc files in
order for them to have access to some ufshcd symbols when all are built
as modules.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
firmare -> firmware
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a glue pci driver for the Synopsys G210 Test Chip.
[mkp: Fixed Kconfig depends and module name]
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a glue platform driver for the Synopsys G210 Test Chip.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for Synopsys G210 Test Chip.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch has the goal to add support for DesignWare UFS Controller
specific operations.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add link status to ufshci.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add unipro attributes.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add UFS 2.0 support to the UFS core driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed typo in ufshcd-pltfrm.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit b704f70ce2 ("SCSI: fix bug in scsi_dev_info_list matching")
changed the way vendor- and model-string matching was carried out in the
routine that looks up entries in a SCSI devinfo list. The new matching
code failed to take into account the case of a maximum-length string; in
such cases it could end up testing for a terminating '\0' byte beyond
the end of the memory allocated to the string. This out-of-bounds bug
was detected by UBSAN.
I don't know if anybody has actually encountered this bug. The symptom
would be that a device entry in the blacklist might not be matched
properly if it contained an 8-character vendor name or a 16-character
model name. Such entries certainly exist in scsi_static_device_list.
This patch fixes the problem by adding a check for a maximum-length
string before the '\0' test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: b704f70ce2 ("SCSI: fix bug in scsi_dev_info_list matching")
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
CC: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we fall back to using LSI on the Croc or Crocodile chip we need to
clear the interrupt so we don't hang the system.
Cc: <stable@vger.kernel.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For block drivers that specify a parent device, convert them to use
device_add_disk().
This conversion was done with the following semantic patch:
@@
struct gendisk *disk;
expression E;
@@
- disk->driverfs_dev = E;
...
- add_disk(disk);
+ device_add_disk(E, disk);
@@
struct gendisk *disk;
expression E1, E2;
@@
- disk->driverfs_dev = E1;
...
E2 = disk;
...
- add_disk(E2);
+ device_add_disk(E1, E2);
...plus some manual fixups for a few missed conversions.
Cc: Jens Axboe <axboe@fb.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that we do have pci_request_mem_regions() and pci_release_mem_regions()
at hand, use it in the lpfc driver.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
CC: James Smart <james.smart@avagotech.com>
CC: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
CC: Martin K. Petersen <martin.petersen@oracle.com>
That macros uses logical "&&" instead of bit-wise "&" which is
apparently wrong. Since the macro is completely unused, simply
remove it, so that nobody can accidentially use it anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The untagged command case in the 53c700 driver has been broken since
host wide tags were enabled because the replaced scsi_find_tag()
function had a special case for the tag value SCSI_NO_TAG to retrieve
sdev->current_cmnd. The replacement function scsi_host_find_tag() has
no such special case and returns NULL causing untagged commands to
trigger a BUG() in the driver. Inspection shows that the 53c700 is the
only driver using this SCSI_NO_TAG case, so a local fix in the driver
suffices to fix this problem globally.
Fixes: 64d513ac31 - "scsi: use host wide tags by default"
Cc: stable@vger.kernel.org # 4.4+
Reported-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_ata_strategy_handler() adds the works of the ata error handler to
system_unbound_wq. This workqueue asynchronously runs work items, so the
ata error handler will be performed concurrently on different CPUs. In
this case, ->host_failed will be decreased simultaneously in
scsi_eh_finish_cmd() on different CPUs, and become abnormal.
It will lead to permanently inequality between ->host_failed and
->host_busy, and scsi error handler thread won't start running. IO
errors after that won't be handled.
Since all scmds must have been handled in the strategy handler, just
remove the decrement in scsi_eh_finish_cmd() and zero ->host_busy after
the strategy handler to fix this race.
Fixes: 50824d6c56 ("[SCSI] libsas: async ata-eh")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This adds a REQ_OP_FLUSH operation that is sent to request_fn
based drivers by the block layer's flush code, instead of
sending requests with the request->cmd_flags REQ_FLUSH bit set.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch drops the compat definition of req_op where it matches
the rq_flag_bits definitions, and drops the related old and compat
code that allowed users to set either the op or flags for the operation.
We also then store the operation in the bi_rw/cmd_flags field similar
to how we used to store the bio ioprio where it sat in the upper bits
of the field.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The req operation REQ_OP is separated from the rq_flag_bits
definition. This converts the block layer drivers to
use req_op to get the op from the request struct.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the simple bi_rw use cases in the block,
drivers, mm and fs code to set/get the bio operation using
bio_set_op_attrs/bio_op
These should be simple one or two liner cases, so I just did them
in one patch. The next patches handle the more complicated
cases in a module per patch.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
