Since we have both USB2 and USB3 PHYs for cdns3 controller, it is
better we have unity APIs to handle both USB2 and USB3's power, it
could simplify code for error handling and further power management
implementation.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Make debugging real problems easier by not trying to disable an EP that
was not yet enabled.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This is a follow-on patch for commit a23be4ed8f ("usb: gadget: aspeed:
improve vhub port irq handling"): for_each_set_bit() is replaced with
simple for() loop because for() loop runs faster on ASPEED BMC.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/dwc3/trace.c: note: in included file (through drivers/usb/dwc3/trace.h):
drivers/usb/dwc3/debug.h:374:39: warning: cast to non-scalar
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add interconnect support in dwc3-qcom driver to vote for bus
bandwidth.
This requires for two different paths - from USB to
DDR. The other is from APPS to USB.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The UDC NET2272 driver includes <linux/gpio.h> but does not
use any symbols from this file, so drop the include.
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Drivers should not assume that interface descriptors have been parsed in
any particular order so use the interface number to look up the second
alternate setting. That number is also what the driver later use to
switch setting.
Note that although the driver could end up verifying the existence of
the expected endpoints on the wrong interface, a later sanity check in
usb_wwan_port_probe() would have caught this before it could cause any
real damage.
Fixes: a78b42824d ("USB: serial: add qualcomm wireless modem driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drivers should not assume that interface descriptors have been parsed in
any particular order so match on interface number instead when rejecting
JTAG interfaces.
Also use the interface struct device for notifications so that the
interface number is included.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is adds a device id for HP LD381 which is a pl2303GC-base device.
Signed-off-by: Scott Chen <scott@labau.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
There exist many FT2232-based JTAG+UART adapter designs in which
FT2232 Channel A is used for JTAG and Channel B is used for UART.
The best way to handle them in Linux is to have the ftdi_sio driver
create a ttyUSB device only for Channel B and not for Channel A:
a ttyUSB device for Channel A would be bogus and will disappear as
soon as the user runs OpenOCD or other applications that access
Channel A for JTAG from userspace, causing undesirable noise for
users. The ftdi_sio driver already has a dedicated quirk for such
JTAG+UART FT2232 adapters, and it requires assigning custom USB IDs
to such adapters and adding these IDs to the driver with the
ftdi_jtag_quirk applied.
Boutique hardware manufacturer Falconia Partners LLC has created a
couple of JTAG+UART adapter designs (one buffered, one unbuffered)
as part of FreeCalypso project, and this hardware is specifically made
to be used with Linux hosts, with the intent that Channel A will be
accessed only from userspace via appropriate applications, and that
Channel B will be supported by the ftdi_sio kernel driver, presenting
a standard ttyUSB device to userspace. Toward this end the hardware
manufacturer will be programming FT2232 EEPROMs with custom USB IDs,
specifically with the intent that these IDs will be recognized by
the ftdi_sio driver with the ftdi_jtag_quirk applied.
Signed-off-by: Mychaela N. Falconia <falcon@freecalypso.org>
[johan: insert in PID order and drop unused define]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
For interfaces that lack a union descriptor, probe for a
"combined-interface" before falling back to the call-management
descriptor instead of the other way round.
This allows for the removal of the NO_DATA_INTERFACE quirk and makes the
probe algorithm somewhat easier to follow.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the data-class define provided by USB core and drop the
driver-specific one.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle broken union functional descriptors where the master-interface
doesn't exist or where its class is of neither Communication or Data
type (as required by the specification) by falling back to
"combined-interface" probing.
Note that this still allows for handling union descriptors with switched
interfaces.
This specifically makes the Whistler radio scanners TRX series devices
work with the driver without adding further quirks to the device-id
table.
Reported-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com>
Tested-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2ad9d544f2.
Drop bogus sanity check; an interface in the active configuration will
always have a current altsetting assigned by USB core.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 88b7381a93 ("USB: Select better matching USB drivers when
available") inadvertently broke usbip functionality. The commit in
question allows USB device drivers to be explicitly matched with
USB devices via the use of driver-provided identifier tables and
match functions, which is useful for a specialised device driver
to be chosen for a device that can also be handled by another,
more generic, device driver.
Prior, the USB device section of usb_device_match() had an
unconditional "return 1" statement, which allowed user-space to bind
USB devices to the usbip_host device driver, if desired. However,
the aforementioned commit changed the default/fallback return
value to zero. This breaks device drivers such as usbip_host, so
this commit restores the legacy behaviour, but only if a device
driver does not have an id_table and a match() function.
In addition, if usb_device_match is called for a device driver
and device pair where the device does not match the id_table of the
device driver in question, then the device driver will be disqualified
for the device. This allows avoiding the default case of "return 1",
which prevents undesirable probe() calls to a driver even though
its id_table did not match the device.
Finally, this commit changes the specialised-driver-to-generic-driver
transition code so that when a device driver returns -ENODEV, a more
generic device driver is only considered if the current device driver
does not have an id_table and a match() function. This ensures that
"generic" drivers such as usbip_host will not be considered specialised
device drivers and will not cause the device to be locked in to the
generic device driver, when a more specialised device driver could be
tried.
All of these changes restore usbip functionality without regressions,
ensure that the specialised/generic device driver selection logic works
as expected with the usb and apple-mfi-fastcharge drivers, and do not
negatively affect the use of devices provided by dummy_hcd.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-5-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves a minor bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is related to the way a candidate USB device driver is
compared against the generic USB device driver. The code in
is_dev_usb_generic_driver() assumes that the device driver in question
is a USB device driver by calling to_usb_device_driver(dev->driver)
to downcast; however I have observed that this assumption is not always
true, through code instrumentation.
This commit avoids the incorrect downcast altogether by comparing
the USB device's driver (i.e., dev->driver) to the generic USB
device driver directly. This method was suggested by Alan Stern.
This bug was found while investigating Andrey Konovalov's report
indicating usbip device driver misbehaviour with the recently merged
generic USB device driver selection feature. The report is linked
below.
Fixes: d5643d2249 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-4-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves a bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is in the logic that determines whether a device currently
bound to a generic USB device driver should be re-probed by a
more specific USB device driver or not. The code in
__usb_bus_reprobe_drivers() used to have the following lines:
if (usb_device_match_id(udev, new_udriver->id_table) == NULL &&
(!new_udriver->match || new_udriver->match(udev) != 0))
return 0;
ret = device_reprobe(dev);
As the reader will notice, the code checks whether the USB device in
consideration matches the identifier table (id_table) of a specific
USB device_driver (new_udriver), followed by a similar check, but this
time with the USB device driver's match function. However, the match
function's return value is not checked correctly. When match() returns
zero, it means that the specific USB device driver is *not* applicable
to the USB device in question, but the code then goes on to reprobe the
device with the new USB device driver under consideration. All this to
say, the logic is inverted.
This bug was found by code inspection and instrumentation while
investigating the root cause of the issue reported by Andrey Konovalov,
where usbip took over syzkaller's virtual USB devices in an undesired
manner. The report is linked below.
Fixes: d5643d2249 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-3-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit reverts commit 7a2f2974f2 ("usbip: Implement a match
function to fix usbip").
In summary, commit d5643d2249 ("USB: Fix device driver race")
inadvertently broke usbip functionality, which I resolved in an incorrect
manner by introducing a match function to usbip, usbip_match(), that
unconditionally returns true.
However, the usbip_match function, as is, causes usbip to take over
virtual devices used by syzkaller for USB fuzzing, which is a regression
reported by Andrey Konovalov.
Furthermore, in conjunction with the fix of another bug, handled by another
patch titled "usbcore/driver: Fix specific driver selection" in this patch
set, the usbip_match function causes unexpected USB subsystem behaviour
when the usbip_host driver is loaded. The unexpected behaviour can be
qualified as follows:
- If commit 41160802ab8e ("USB: Simplify USB ID table match") is included
in the kernel, then all USB devices are bound to the usbip_host
driver, which appears to the user as if all USB devices were
disconnected.
- If the same commit (41160802ab8e) is not in the kernel (as is the case
with v5.8.10) then all USB devices are re-probed and re-bound to their
original device drivers, which appears to the user as a disconnection
and re-connection of USB devices.
Please note that this commit will make usbip non-operational again,
until yet another patch in this patch set is merged, titled
"usbcore/driver: Accommodate usbip".
Cc: <stable@vger.kernel.org> # 5.8: 41160802ab8e: USB: Simplify USB ID table match
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-2-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_recv() function can handle data on the stack, as
well as properly detecting short reads, so move to use that function
instead of the older usb_control_msg() call. This ends up removing a
lot of extra lines in the driver.
v2: change API of usb_control_msg_send()
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Link: https://lore.kernel.org/r/20200914153756.3412156-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-12-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They need to specify how memory is to be allocated,
as control messages need to work in contexts that require GFP_NOIO.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200923134348.23862-9-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d6a4992495.
Control messages are needed in contexts when memory allocations
are restricted, such as handling device resets and runtime PM.
For this reason the control message API internally uses GFP_NOIO.
This is a band aid introduced because when we recognized the issue,
the call chains were highly convoluted. Continuing this trend
is not a good idea.
So I am shooting the whole kennel here.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200923134348.23862-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DPRAM memory from the USB High Speed Device Port (UDPHS) hardware
block was increased. This patch updates the endpoint allocation for sam9x60
to take advantage of this larger memory. At the same time the
constraint to allocate the endpoints in order was lifted. To handle old
and new hardware in the same driver the ep_prealloc was added.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Use 1 bank endpoints for control transfers
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Simplify the endpoint allocation and cleanup the code.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Instead of trying to match every possible compatible use
of_find_matching_node_and_match() and pass the compatible array.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Call dwc2_debugfs_exit() and dwc2_hcd_remove() (if the HCD was enabled
earlier) when usb_add_gadget_udc() has failed. This ensures that the
debugfs entries created by dwc2_debugfs_init() as well as the HCD are
cleaned up in the error path.
Fixes: 207324a321 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The user may have more information to override the HW parameter to
specify the maximum_speed. However, if the user specifies a
maximum_speed that the controller doesn't support, print out a warning.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the maximum_speed is not specified, default the device speed base on
its HW capability. Don't prematurely check HW capability before
validating the maximum_speed device property. The device property takes
precedence in dwc->maximum_speed.
Fixes: 0e1e5c47f7 ("usb: dwc3: add support for USB 2.0-only core configuration")
Reported-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
According the programming guide (for all DWC3 IPs), when the driver
handles ClearFeature(halt) request, it should issue CLEAR_STALL command
_after_ the END_TRANSFER command completes. The END_TRANSFER command may
take some time to complete. So, delay the ClearFeature(halt) request
control status stage and wait for END_TRANSFER command completion
interrupt. Only after END_TRANSFER command completes that the driver
may issue CLEAR_STALL command.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The function driver may queue new requests right after halting the
endpoint (i.e. queue new requests while the endpoint is stalled).
There's no restriction preventing it from doing so. However, dwc3
currently drops those requests after CLEAR_STALL. The driver should only
drop started requests. Keep the pending requests in the pending list to
resume and process them after the host issues ClearFeature(Halt) to the
endpoint.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
commit 2b74b0a04d ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
adds important bounds checking however it unfortunately also introduces a
bug with respect to section 3.3.1 of the NCM specification.
wDatagramIndex[1] : "Byte index, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramLength[1]: "Byte length, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramIndex[1] and wDatagramLength[1] respectively then may be zero but
that does not mean we should throw away the data referenced by
wDatagramIndex[0] and wDatagramLength[0] as is currently the case.
Breaking the loop on (index2 == 0 || dg_len2 == 0) should come at the end
as was previously the case and checks for index2 and dg_len2 should be
removed since zero is valid.
I'm not sure how much testing the above patch received but for me right now
after enumeration ping doesn't work. Reverting the commit restores ping,
scp, etc.
The extra validation associated with wDatagramIndex[0] and
wDatagramLength[0] appears to be valid so, this change removes the incorrect
restriction on wDatagramIndex[1] and wDatagramLength[1] restoring data
processing between host and device.
Fixes: 2b74b0a04d ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
Cc: Ilja Van Sprundel <ivansprundel@ioactive.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200920170158.1217068-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To show the trb ring of streams, use the exsiting ring files of bulk ep
to show trb ring of one specific stream ID, which stream ID's trb ring
will be shown, is controlled by a new debugfs file stream_id, this is to
avoid to create a large number of dir for every allocate stream IDs,
another debugfs file stream_context_array is created to show all the
allocated stream context array entries.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure xHC completes the configure endpoint command and xhci driver
sets the ring pointers correctly before we create the user readable
debugfs file.
In theory there was a small gap where a user could have read the
debugfs file and cause a NULL pointer dereference error as ring
pointer was not yet set, in practise we want this change to simplify
the upcoming streams debugfs support.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
controllers with XHCI_AVOID_BEI quirk cause too frequent interrupts
and affect power management.
To avoid interrupting on every isochronous interval the BEI (Block
Event Interrupt) flag is set for all except the last Isoch TRB in a URB.
This lead to event ring filling up in case several isoc URB were
queued and cancelled rapidly, which some controllers didn't
handle well, and thus the XHCI_AVOID_BEI quirk was introduced.
see commit 227a4fd801 ("usb: xhci: apply XHCI_AVOID_BEI quirk to all
Intel xHCI controllers")
With the XHCI_AVOID_BEI quirk each Isoch TRB will trigger an interrupt.
This can cause up to 8000 interrupts per second for isochronous transfers
with HD USB3 cameras, affecting power saving.
The event ring fits 256 events, instead of interrupting on every
isochronous TRB if XHCI_AVOID_BEI is set we make sure at least every
8th Isochronous TRB asserts an interrupt, clearing the event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the xhci-plat.c is the platform driver, after the runtime pm is
enabled, the xhci_suspend is called if nothing is connected on
the port. When the system goes to suspend, it will call xhci_suspend again
if USB wakeup is enabled.
Since the runtime suspend wakeup setting is not always the same as
system suspend wakeup setting, eg, at runtime suspend we always need
wakeup if the controller is in low power mode; but at system suspend,
we may not need wakeup. So, we move the judgement after changing
wakeup setting.
[commit message rewording -Mathias]
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this change, there will be a wakeup entry at /sys/../power/wakeup,
and the user could use this entry to choose whether enable xhci wakeup
features (wake up system from suspend) or not.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DRD controllers (eg, dwc3 & cdns3) have PHY management at
their own driver to cover both device and host mode, so add one
priv quirk for such users to skip PHY management from HCD core.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The if {} condition is duplicated with outer if {} condition.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms (eg cdns3) may have special sequences between
xhci_bus_suspend and xhci_suspend, add .suspend_quick for it.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some xhci hosts (eg dwc3 and cdns3) do not use OF to create
platform device, they create xhci-plat platform device runtime.
And these platforms may also have quirks, and the quirks could
be supplied by their parent device through platform data.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Buffers should be u8*, not unsigned char*
Buffers have an unsigned length and using an int
as a boolean is a bit outdated.
No functional change intended.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200917110235.11854-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the comment in usb_alloc_dev correctly states, drivers can't use
the DMA API on usb device, and at least calling dma_set_mask on them
is highly dangerous. Unlike what the comment states upper level drivers
also can't really use the presence of a dma mask to check for DMA
support, as the dma_mask is set by default for most busses.
Setting the dma_mask comes from "[PATCH] usbcore dma updates (and doc)"
in BitKeeper times, as it seems like it was primarily for setting the
NETIF_F_HIGHDMA flag in USB drivers, something that has long been
fixed up since.
Setting the dma_pfn_offset comes from commit b44bbc46a8
("usb: core: setup dma_pfn_offset for USB devices and, interfaces"),
which worked around the fact that the scsi_calculate_bounce_limits
functions wasn't going through the proper driver interface to query
DMA information, but that function was removed in commit 21e07dba9f
("scsi: reduce use of block bounce buffers") years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CRC calculation done by genksyms is triggered when the parser hits
EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the
types of the function parameters, and uses that as the input for the CRC
calculation. In the case of forward-declared structs, the type expands
to 'UNKNOWN'. Following this, it appears that the result of the
expansion of each type is cached somewhere, and seems to be re-used
when/if the same type is seen again for another exported symbol in the
same C file.
Unfortunately, this can cause CRC 'stability' issues when a struct
definition becomes visible in the middle of a C file. For example, let's
assume code with the following pattern:
struct foo;
int bar(struct foo *arg)
{
/* Do work ... */
}
EXPORT_SYMBOL_GPL(bar);
/* This contains struct foo's definition */
#include "foo.h"
int baz(struct foo *arg)
{
/* Do more work ... */
}
EXPORT_SYMBOL_GPL(baz);
Here, baz's CRC will be computed using the expansion of struct foo that
was cached after bar's CRC calculation ('UNKOWN' here). But if
EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol
trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded
late, during baz's CRC calculation, which now has visibility over the
full struct definition, hence resulting in a different CRC for baz.
The proper fix for this certainly is in genksyms, but that will take me
some time to get right. In the meantime, we have seen one occurrence of
this in the ehci-hcd code which hits this problem because of the way it
includes C files halfway through the code together with an unlucky mix
of symbol trimming.
In order to workaround this, move the include done in ehci-hub.c early
in ehci-hcd.c, hence making sure the struct definitions are visible to
the entire file. This improves CRC stability of the ehci-hcd exports
even when symbol trimming is enabled.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20200916171825.3228122-1-qperret@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check and return if there are errors. The response bits are valid
only on no errors.
Fixes: b7404a29cd ("usb: typec: intel_pmc_mux: Definitions for response status bits")
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook.
This notebook come with usb touchpad. And we would like to disable
touchpad wakeup on this notebook by default.
Signed-off-by: Penghao <penghao@uniontech.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907023026.28189-1-penghao@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ROLE_CONTROL register would not have the actual CC terminations
unless the port does not set ROLE_CONTROL.DRP. For DRP ports,
CC_STATUS.cc1/cc2 indicates the final terminations applied
when TCPC enters potential_connect_as_source/_sink.
For DRP ports, infer port role from CC_STATUS and set corresponding
CC terminations before setting the orientation.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20200901025927.3596190-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPCI spec forbids direct access of TX_BUF_BYTE_x register.
The existing version of tcpci driver assumes that those registers
are directly addressible. Add support for tcpci chips which do
not support direct access to TX_BUF_BYTE_x registers. TX_BUF_BYTE_x
can only be accessed by I2C_WRITE_BYTE_COUNT.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20200901025927.3596190-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer has introduced a new macro for recording the result
of a command. Use it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200916094026.30085-3-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Fixes: 115bb1ffa5 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoC expects the USB Type-C ports numbers to be starting with 0.
If the port number is passed as it is, the IOM status will not be
updated. The IOM port status check fails which will eventually
lead to PMC IPC communication failure.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Suggested-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the driver now needs to find the IOM ACPI node, the
driver depends on ACPI. Without the dependency set, the
driver will only fail to compile when ACPI is not enabled.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Fixes: 115bb1ffa5 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the embedded controller firmware does not
terminate the list of alternate modes that the partner
supports in its response to the GET_ALTERNATE_MODES command.
Instead the firmware returns the supported alternate modes
over and over again until the driver stops requesting them.
If that happens, the number of modes for each alternate mode
will exceed the maximum 6 that is defined in the USB Power
Delivery specification. Making sure that can't happen by
adding a check for it.
This fixes NULL pointer dereference that is caused by the
overrun.
Fixes: ad74b8649b ("usb: typec: ucsi: Preliminary support for alternate modes")
Cc: stable@vger.kernel.org
Reported-by: Zwane Mwaikambo <zwanem@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI specification quite clearly states that if a command
can't be completed in 10ms, the firmware must notify
about BUSY condition. Unfortunately almost none of the
platforms (the firmware on them) generate the BUSY
notification even if a command can't be completed in time.
The driver already considered that, and used a timeout
value of 5 seconds, but processing especially the alternate
mode discovery commands takes often considerable amount of
time from the firmware, much more than the 5 seconds. That
happens especially after bootup when devices are already
connected to the USB Type-C connector. For now on those
platforms the alternate mode discovery has simply failed
because of the timeout.
To improve the situation, increasing the timeout value for
the command completion to 1 minute. That should give enough
time for even the slowest firmware to process the commands.
Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_recv() function can handle data on the stack, as
well as properly detecting short reads, so move to use that function
instead of the older usb_control_msg() call. This ends up removing a
lot of extra lines in the driver.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Link: https://lore.kernel.org/r/20200914153756.3412156-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few calls to usb_control_msg() that can be converted to use
usb_control_msg_send() instead, so do that in order to make the error
checking a bit simpler and the code smaller.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200914153756.3412156-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few calls to usb_control_msg() that can be converted to use
usb_control_msg_send() instead, so do that in order to make the error
checking a bit simpler.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200914153756.3412156-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New core functions to make sending/receiving USB control messages easier
and saner.
In discussions, it turns out that the large majority of users of
usb_control_msg() do so in potentially incorrect ways. The most common
issue is where a "short" message is received, yet never detected
properly due to "incorrect" error handling.
Handle all of this in the USB core with two new functions to try to make
working with USB control messages simpler.
No more need for dynamic data, messages can be on the stack, and only
"complete" send/receive will work without causing an error.
Link: https://lore.kernel.org/r/20200914153756.3412156-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_usb_pipe_sanity_check() is a great function, so let's move it into
the USB core so that other parts of the kernel, including the USB core,
can call it.
Name it usb_pipe_type_check() to match the existing
usb_urb_ep_type_check() call, which now uses this function.
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Eli Billauer <eli.billauer@gmail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Tsoy <alexander@tsoy.me>
Cc: "Geoffrey D. Bennett" <g@b4.vu>
Cc: Jussi Laako <jussi@sonarnerd.net>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Dmitry Panchenko <dmitry@d-systems.ee>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jesus Ramos <jesus-ramos@live.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mediatek MT6360 is a multi-functional IC that includes USB Type-C.
It works with Type-C Port Controller Manager to provide USB PD
and USB Type-C functionalities.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1598928042-22115-1-git-send-email-u0084500@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'distrust_firmware' module parameter dates from 2004 and the USB
subsystem is a lot more mature and reliable now than it was then.
Alter the default to false now.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200910212512.16670-2-hamish.martin@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some integrated OHCI controller hubs do not expose all ports of the hub
to pins on the SoC. In some cases the unconnected ports generate
spurious over-current events. For example the Broadcom 56060/Ranger 2 SoC
contains a nominally 3 port hub but only the first port is wired.
Default behaviour for ohci-platform driver is to use global over-current
protection mode (AKA "ganged"). This leads to the spurious over-current
events affecting all ports in the hub.
We now alter the default to use per-port over-current protection.
This patch results in the following configuration changes depending
on quirks:
- For quirk OHCI_QUIRK_SUPERIO no changes. These systems remain set up
for ganged power switching and no over-current protection.
- For quirk OHCI_QUIRK_AMD756 or OHCI_QUIRK_HUB_POWER power switching
remains at none, while over-current protection is now guaranteed to be
set to per-port rather than the previous behaviour where it was either
none or global over-current protection depending on the value at
function entry.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200910212512.16670-1-hamish.martin@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci controller found in some Broadcom switches with integrated SoCs
has an issue which causes a soft lockup with large transfers like you
see when running ext4 on USB3 flash drive.
Port the fix from the Broadcom XLDK to increase the OUT_THRESHOLD to
avoid the problem.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200913215926.29880-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Here are some new device ids for 5.9.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCX1embwAKCRALxc3C7H1l
CLYoAQDVrO56s8bOd5JW3NpuDCDUgDSt3dBrXNF+PhHKX0TDAAEAztQesI4MgXLz
p0X1nJvdlwQgRTTJzI84HaUTRZk+EQc=
=1W7v
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.9-rc5
Here are some new device ids for 5.9.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: support dynamic Quectel USB compositions
USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules
USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
This adds support for device data role, and data role
swapping. The driver no longer relies on the cached role, as
it may not be valid (for example after bootup). Instead, the
role is always checked by readding the port status from IOM.
Note. After this, the orientation is always only cached, so
the driver does not support scenario where the role is set
before orientation. It means the typec drivers must always
set the orientation first before role.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Tested-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20200907142428.35838-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PMC microcontroller that we use for configuration, does
not supply any status information back. For port status we
need to talk to another controller on the board called IOM
(I/O manager).
By checking the port status before configuring the muxes, we
can make sure that we do not reconfigure the port after
bootup when the system firmware (for example BIOS) has
already configured it.
Using the status information also to check if DisplayPort
HPD is still asserted when the cable plug is disconnected,
and clearing it if it is.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Tested-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20200907142428.35838-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bits 4 and 5 are reserved in Alternate modes.
SBU Orientation and HSL Orientation needs to be configured only during
initial cable detection in USB connect flow based on device property of
"sbu-orientation" and "hsl-orientation".
Configuring these reserved bits in the Alternate modes may result in delay
in display link training or some unexpected behaviour.
So do not configure them while issuing Alternate Mode requests.
Fixes: ff4a30d5e2 ("usb: typec: mux: intel_pmc_mux: Support for static SBU/HSL orientation")
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bit 14 is reserved in Alternate mode.
In DP Alternate Mode state, if the HPD_STATE (bit 7) field in the
status update command VDO is set to HPD_HIGH, HPD is configured via
separate HPD mode request after configuring DP Alternate mode request.
Configuring reserved bit may show unexpected behaviour.
So do not configure them while issuing the Alternate Mode request.
Fixes: 7990be48ef ("usb: typec: mux: intel: Handle alt mode HPD_HIGH")
Cc: stable@vger.kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the connection descriptors can't be stored into the
list anymore, there is no need for the data structure.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200904125123.83725-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no reason for uas to use a smaller value of max_sectors than
usb-storage.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903181725.2931-3-tom.ty89@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scsi_add_host_with_dma() instead of scsi_add_host().
When the scsi request queue is initialized/allocated, hw_max_sectors is clamped
to the dma max mapping size. Therefore, the correct device that should be used
for the clamping needs to be set.
The same clamping is still needed in uas as hw_max_sectors could be changed
there. The original clamping would be invalidated in such cases.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903181725.2931-2-tom.ty89@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scsi_add_host_with_dma() instead of scsi_add_host().
When the scsi request queue is initialized/allocated, hw_max_sectors is clamped
to the dma max mapping size. Therefore, the correct device that should be used
for the clamping needs to be set.
The same clamping is still needed in usb-storage as hw_max_sectors could be
changed there. The original clamping would be invalidated in such cases.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903181725.2931-1-tom.ty89@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903112554.34263-4-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903112554.34263-3-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903112554.34263-5-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903112554.34263-8-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903112554.34263-9-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8bb54ab573 ("usbcore: add usb_device_driver definition") added
the printk() calls with the error massages spoilt due to the stray tabs
in the middle. Remove these tabs and convert printk() calls to pr_err()
for consistency with the other code, while at it.
Fixes: 8bb54ab573 ("usbcore: add usb_device_driver definition")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/4beb55c4-eb34-7744-155f-033b8f527e23@omprussia.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7a410953d1.
This commit breaks USB on meson-gxl-s905x-libretech-cc. Reverting
the change solves the issue.
In fact, according to the reset framework code, consumers must not use
reset_control_(de)assert() on shared reset lines when reset_control_reset
has been used, and vice-versa.
Moreover, with this commit, usb is not guaranted to be reset since the
reset is likely to be initially deasserted.
Reverting the commit will bring back the suspend warning mentioned in the
commit description. Nevertheless, a warning is much less critical than
breaking dwc3-meson-g12a USB completely. We will address the warning
issue in another way as a 2nd step.
Fixes: 7a410953d1 ("usb: dwc3: meson-g12a: fix shared reset control use")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20200827144810.26657-1-aouledameur@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Failing probe with -EPROBE_DEFER until all dependencies
listed in the _DEP (Operation Region Dependencies) object
have been met.
This will fix an issue where on some platforms UCSI ACPI
driver fails to probe because the address space handler for
the operation region that the UCSI ACPI interface uses has
not been loaded yet.
Fixes: 8243edf441 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace drivers that use a SetConfiguration() request to "lightweight"
reset an already configured usb device might cause data toggles to get out
of sync between the device and host, and the device becomes unusable.
The xHCI host requires endpoints to be dropped and added back to reset the
toggle. If USB core notices the new configuration is the same as the
current active configuration it will avoid these extra steps by calling
usb_reset_configuration() instead of usb_set_configuration().
A SetConfiguration() request will reset the device side data toggles.
Make sure usb_reset_configuration() function also drops and adds back the
endpoints to ensure data toggles are in sync.
To avoid code duplication split the current usb_disable_device() function
and reuse the endpoint specific part.
Cc: stable <stable@vger.kernel.org>
Tested-by: Martin Thierer <mthierer@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pinctrl setting may lost during the system suspend
(eg, imx7ulp), it needs to restore them after system resume.
Meanwhile, some platforms may need to set special pinctrl
for power comsumption.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge 5.9-rc3 into usb-next
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that:
- the usb gadget patch now does not break some systems, and
actually does what it was intended to do. Many thanks to
Marek Szyprowski for quickly noticing and testing the patch
from Andy Shevchenko to resolve this issue.
- some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the original pull request patches are all here, and
they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX0t32g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylFMACeLEQgeN1rmfQfLyo2NHROQEeDhnIAniLMhchZ
p9dXWJ8aNeyI5OrNjD5b
=Vd05
-----END PGP SIGNATURE-----
Merge tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that
the usb gadget patch now does not break some systems, and actually
does what it was intended to do. Many thanks to Marek Szyprowski for
quickly noticing and testing the patch from Andy Shevchenko to resolve
this issue.
Additionally, some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the patches are all here, and they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues"
* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: storage: Add unusual_uas entry for Sony PSZ drives
USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
USB: gadget: u_f: Unbreak offset calculation in VLAs
USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
USB: PHY: JZ4770: Fix static checker warning.
USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
USB: gadget: u_f: add overflow checks to VLA macros
xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
xhci: Do warm-reset when both CAS and XDEV_RESUME are set
usb: host: xhci: fix ep context print mismatch in debugfs
usb: uas: Add quirk for PNY Pro Elite
tools: usb: move to tools buildsystem
USB: Fix device driver race
USB: Also match device drivers using the ->match vfunc
usb: host: xhci-tegra: fix tegra_xusb_get_phy()
usb: host: xhci-tegra: otg usb2/usb3 port init
usb: hcd: Fix use after free in usb_hcd_pci_remove()
usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
...
"tReceiverResponse 15 ms Section 6.6.2
The receiver of a Message requiring a response Shall respond
within tReceiverResponse in order to ensure that the
sender’s SenderResponseTimer does not expire."
When the cpu complex is busy running other lower priority
work items, TCPM's work queue sometimes does not get scheduled
on time to meet the above requirement from the spec.
Moving to kthread_work apis to run with real time priority.
Further, as observed in 1ff688209e, moving to hrtimers to
overcome scheduling latency while scheduling the delayed work.
TCPM has three work streams:
1. tcpm_state_machine
2. vdm_state_machine
3. event_work
tcpm_state_machine and vdm_state_machine both schedule work in
future i.e. delayed. Hence each of them have a corresponding
hrtimer, tcpm_state_machine_timer & vdm_state_machine_timer.
When work is queued right away kthread_queue_work is used.
Else, the relevant timer is programmed and made to queue
the kthread_work upon timer expiry.
kthread_create_worker only creates one kthread worker thread,
hence single threadedness of workqueue is retained.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200818192758.2562908-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.
This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."
The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after tSwapSourceStart(20ms).
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200817183828.1895015-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PSZ-HA* family of USB disk drives from Sony can't handle the
REPORT OPCODES command when using the UAS protocol. This patch adds
an appropriate quirks entry.
Reported-and-tested-by: Till Dörges <doerges@pre-sense.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device does not support UAS properly and a similar entry already
exists in drivers/usb/storage/unusual_uas.h. Without this patch,
storage_probe() defers the handling of this device to UAS, which cannot
handle it either.
Tested-by: Brice Goglin <brice.goglin@gmail.com>
Fixes: bc3bdb12bb ("usb-storage: Disable UAS on JMicron SATA enclosure")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ohci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
Fixes: 62194244cf ("USB: Add Samsung Exynos OHCI diver")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200826144931.1828-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inadvertently the commit b1cd1b65af ("USB: gadget: u_f: add overflow checks
to VLA macros") makes VLA macros to always return 0 due to different scope of
two variables of the same name. Obviously we need to have only one.
Fixes: b1cd1b65af ("USB: gadget: u_f: add overflow checks to VLA macros")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b8 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
Reported-and-tested-by: Jean-Christophe Barnoud <jcbarnoud@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
Link: https://lore.kernel.org/r/20200826194624.GA412633@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernel/cpu.c: don't use snprintf() for sysfs attrs
As per the documentation (Documentation/filesystems/sysfs.rst),
snprintf() should not be used for formatting values returned by sysfs.
In all of these cases, sprintf() suffices as we know that the formatted
strings will be less than PAGE_SIZE in length.
Issue identified by Coccinelle.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200824222322.22962-1-alex.dewar90@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch addresses the compliance test failures while running TDA
2.3.1.1 and TDA 2.3.1.2 of the "PD Communications Engine USB PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
While the purpose of TDA 2.3.1.1 and TDA 2.3.1.2 is to verify that
the static and dynamic electrical capabilities of a Source meet the
requirements for each PDO offered, while doing so, the tests also
monitor that the timing of the VBUS waveform versus the messages meets
the requirements for Hard Reset defined in PROT-PROC-HR-TSTR as
mentioned in step 11 of TDA.2.3.1.1 and step 15 of TDA.2.3.1.2.
TDB.2.2.13.1: PROT-PROC-HR-TSTR Procedure and Checks for Tester
Originated Hard Reset
Purpose: To perform the appropriate protocol checks relating to any
circumstance in which the Hard Reset signal is sent by the Tester.
UUT is behaving as source:
The Tester sends a Hard Reset signal.
1. Check VBUS stays within present valid voltage range for
tPSHardReset min (25ms) after last bit of Hard Reset signal.
[PROT_PROC_HR_TSTR_1]
2. Check that VBUS starts to fall below present valid voltage range by
tPSHardReset max (35ms). [PROT_PROC_HR_TSTR_2]
3. Check that VBUS reaches vSafe0V within tSafe0v max (650 ms).
[PROT_PROC_HR_TSTR_3]
4. Check that VBUS starts rising to vSafe5V after a delay of
tSrcRecover (0.66s - 1s) from reaching vSafe0V. [PROT_PROC_HR_TSTR_4]
5. Check that VBUS reaches vSafe5V within tSrcTurnOn max (275ms) of
rising above vSafe0v max (0.8V). [PROT_PROC_HR_TSTR_5] Power Delivery
Compliance Plan 139 6. Check that Source Capabilities are finished
sending within tFirstSourceCap max (250ms) of VBUS reaching vSafe5v
min. [PROT_PROC_HR_TSTR_6].
This is in line with 7.1.5 Response to Hard Resets of the USB Power
Delivery Specification Revision 3.0, Version 1.2,
"Hard Reset Signaling indicates a communication failure has occurred
and the Source Shall stop driving VCONN, Shall remove Rp from the
VCONN pin and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The
USB connection May reset during a Hard Reset since the VBUS voltage
will be less than vSafe5V for an extended period of time. After
establishing the vSafe0V voltage condition on VBUS, the Source Shall
wait tSrcRecover before re-applying VCONN and restoring VBUS to
vSafe5V. A Source Shall conform to the VCONN timing as specified in
[USB Type-C 1.3]."
With the above guidelines from the spec in mind, TCPM does not turn
off VCONN while entering SRC_HARD_RESET_VBUS_OFF. The patch makes TCPM
turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF and turn it back
on while entering SRC_HARD_RESET_VBUS_ON along with vbus instead of
having VCONN on through hardreset.
Also, the spec clearly states that "After establishing the vSafe0V
voltage condition on VBUS", the Source Shall wait tSrcRecover before
re-applying VCONN and restoring VBUS to vSafe5V.
TCPM does not conform to this requirement. If the TCPC driver calls
tcpm_vbus_change with vbus off signal, TCPM right away enters
SRC_HARD_RESET_VBUS_ON without waiting for tSrcRecover.
For TCPC's which are buggy/does not call tcpm_vbus_change, TCPM
assumes that the vsafe0v is instantaneous as TCPM only waits
tSrcRecover instead of waiting for tSafe0v + tSrcRecover.
This patch also fixes this behavior by making sure that TCPM waits for
tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON when
tcpm_vbus_change is called by TCPC.
When TCPC does not call tcpm_vbus_change, TCPM assumes the worst case
i.e. tSafe0v + tSrcRecover before transitioning into
SRC_HARD_RESET_VBUS_ON.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200817184601.1899929-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 2a6c0b82e6 ("USB: PHY: JZ4770: Add support for new
Ingenic SoCs.") introduced the initialization function for different
chips, but left the relevant code involved in the resetting process
in the original function, resulting in uninitialized variable calls.
Fixes: 2a6c0b82e6 ("USB: PHY: JZ4770: Add support for new Ingenic SoCs.").
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200825081654.18186-2-zhouyanjie@wanyeetech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some values extracted by ncm_unwrap_ntb() could possibly lead to several
different out of bounds reads of memory. Specifically the values passed
to netdev_alloc_skb_ip_align() need to be checked so that memory is not
overflowed.
Resolve this by applying bounds checking to a number of different
indexes and lengths of the structure parsing logic.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
size can potentially hold an overflowed value if its assigned expression
is left unchecked, leading to a smaller than needed allocation when
vla_group_size() is used by callers to allocate memory.
To fix this, add a test for saturation before declaring variables and an
overflow check to (n) * sizeof(type).
If the expression results in overflow, vla_group_size() will return SIZE_MAX.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device added has an FTDI chip inside.
The device is used to connect Xsens USB Motion Trackers.
Cc: stable@vger.kernel.org
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some device drivers call libusb_clear_halt when target ep queue
is not empty. (eg. spice client connected to qemu for usb redir)
Before commit f5249461b5 ("xhci: Clear the host side toggle
manually when endpoint is soft reset"), that works well.
But now, we got the error log:
EP not empty, refuse reset
xhci_endpoint_reset failed and left ep_state's EP_SOFT_CLEAR_TOGGLE
bit still set
So all the subsequent urb sumbits to the ep will fail with the
warn log:
Can't enqueue URB while manually clearing toggle
We need to clear ep_state EP_SOFT_CLEAR_TOGGLE bit after
xhci_endpoint_reset, even if it failed.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: stable <stable@vger.kernel.org> # v4.17+
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes re-plugging a USB device during system sleep renders the device
useless:
[ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[ 176.496485] usb 2-4: Waited 2000ms for CONNECT
[ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[ 176.497103] usb 2-4: can't resume, status -19
[ 176.497438] usb usb2-port4: logical disconnect
Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.
So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dci is 0 based and xhci_get_ep_ctx() will do ep index increment to get
the ep context.
[rename dci to ep_index -Mathias]
Cc: stable <stable@vger.kernel.org> # v4.15+
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two parameters are used to improve USB signal for board level,
in this commit, we read it from the dtb, and write to related register
during the initialization.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Remove unused 'udc' variable to fix compile warnings:
drivers/usb/gadget/udc/s3c2410_udc.c: In function 's3c2410_udc_dequeue':
drivers/usb/gadget/udc/s3c2410_udc.c:1268:22: warning: variable 'udc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200731074122.6484-1-krzk@kernel.org
There is no real phy driver, so s3c-hsudc just pokes the registers
itself. Improve this a little by making it a platform data callback
like we do for gpios.
There is only one board using this driver, and it's unlikely
that another would be added, so this is a minimal workaround.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200806182059.2431-9-krzk@kernel.org
[krzk: Include regs-s3c2443-clock.h in ifdef to fixup build on s3c6400]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The resources are correctly initialized, so just use them
instead of relying on hardcoded data from platform headers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-8-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12
pass-through command (i.e. it just hangs). If it doesn't support this
command, it should respond properly to the host. Let's just add a quirk
to be able to move forward with other operations.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Link: https://lore.kernel.org/r/2b0585228b003eedcc82db84697b31477df152e0.1597803605.git.thinhn@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three ZLP fixes on dwc3 and a resource leak fix on the TCM gadget
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=GSI6
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.9-rc
Three ZLP fixes on dwc3 and a resource leak fix on the TCM gadget
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'fixes-for-v5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: dwc3: gadget: Handle ZLP for sg requests
usb: dwc3: gadget: Fix handling ZLP
usb: dwc3: gadget: Don't setup more than requested
usb: gadget: f_tcm: Fix some resource leaks in some error paths
__check_usb_generic() doesn't explain very well what the
function actually does: It checks to see whether the driver is
non-generic and matches the device.
Change it to check_for_non_generic_match()
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200818110445.509668-2-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new device with a specialised device driver is plugged in, the
new driver will be modprobe()'d but the driver core will attach the
"generic" driver to the device.
After that, nothing will trigger a reprobe when the modprobe()'d device
driver has finished initialising, as the device has the "generic"
driver attached to it.
Trigger a reprobe ourselves when new specialised drivers get registered.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-3-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only ever used the ID table matching before, but we should also support
open-coded match functions.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-1-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tegra_xusb_init_usb_phy() should initialize "otg_usb2_port" and
"otg_usb3_port" with -EINVAL because "0" is a valid value
represents usb2 port 0 or usb3 port 0.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200811093143.699541-1-jckuo@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The board doesn't need the quirks to be run, and takes care of its own
initialization through a reset controller device. So let's bypass them.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-8-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c65822fef4.
The initialization of Raspberry Pi 4's USB chip is now handled through a
reset controller. No need to directly call the firmware routine through a
PCI quirk.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-7-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some atypical users of xhci-pci might need to manually reset their xHCI
controller before starting the HCD setup. Check if a reset controller
device is available to the PCI bus and trigger a reset.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-6-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817090209.26351-8-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817090209.26351-7-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817090209.26351-6-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817090209.26351-5-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817090209.26351-4-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817090209.26351-3-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817090209.26351-2-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_kill_anchored_urbs() is commonly used to cancel all URBs on an
anchor just before releasing resources which the URBs rely on. By doing
so, users of this function rely on that no completer callbacks will take
place from any URB on the anchor after it returns.
However if this function is called in parallel with __usb_hcd_giveback_urb
processing a URB on the anchor, the latter may call the completer
callback after usb_kill_anchored_urbs() returns. This can lead to a
kernel panic due to use after release of memory in interrupt context.
The race condition is that __usb_hcd_giveback_urb() first unanchors the URB
and then makes the completer callback. Such URB is hence invisible to
usb_kill_anchored_urbs(), allowing it to return before the completer has
been called, since the anchor's urb_list is empty.
Even worse, if the racing completer callback resubmits the URB, it may
remain in the system long after usb_kill_anchored_urbs() returns.
Hence list_empty(&anchor->urb_list), which is used in the existing
while-loop, doesn't reliably ensure that all URBs of the anchor are gone.
A similar problem exists with usb_poison_anchored_urbs() and
usb_scuttle_anchored_urbs().
This patch adds an external do-while loop, which ensures that all URBs
are indeed handled before these three functions return. This change has
no effect at all unless the race condition occurs, in which case the
loop will busy-wait until the racing completer callback has finished.
This is a rare condition, so the CPU waste of this spinning is
negligible.
The additional do-while loop relies on usb_anchor_check_wakeup(), which
returns true iff the anchor list is empty, and there is no
__usb_hcd_giveback_urb() in the system that is in the middle of the
unanchor-before-complete phase. The @suspend_wakeups member of
struct usb_anchor is used for this purpose, which was introduced to solve
another problem which the same race condition causes, in commit
6ec4147e7b ("usb-anchor: Delay usb_wait_anchor_empty_timeout wake up
till completion is done").
The surely_empty variable is necessary, because usb_anchor_check_wakeup()
must be called with the lock held to prevent races. However the spinlock
must be released and reacquired if the outer loop spins with an empty
URB list while waiting for the unanchor-before-complete passage to finish:
The completer callback may very well attempt to take the very same lock.
To summarize, using usb_anchor_check_wakeup() means that the patched
functions can return only when the anchor's list is empty, and there is
no invisible URB being processed. Since the inner while loop finishes on
the empty list condition, the new do-while loop will terminate as well,
except for when the said race condition occurs.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200731054650.30644-1-eli.billauer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The exact error that happened trying to get the VBUS supply can be
useful to troubleshoot what's going on.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200806160248.3936771-2-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the connector is the child of a USB port and that USB port already
has a VBUS supply attached to it, it would be redundant to require the
connector to have a VBUS supply. In this case, allow the VBUS supply to
be optional.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200806160248.3936771-1-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a usb_stor_dbg debug message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200810083211.48282-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 081da1325d ("usb: typec: ucsi: displayport: Fix a potential race
during registration") made the ucsi code hold con->lock in
ucsi_register_displayport(). But we really don't want any interactions
with the connector to run before the port-registration process is fully
complete.
This commit moves the taking of con->lock from ucsi_register_displayport()
into ucsi_register_port() to achieve this.
Cc: stable@vger.kernel.org
Fixes: 081da1325d ("usb: typec: ucsi: displayport: Fix a potential race during registration")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().
Push the taking of the lock down into these 2 functions, renaming
ucsi_run_command() to ucsi_send_command() which was an existing
wrapper already taking the lock for its callers.
This simplifies things for the callers and removes the difference
between ucsi_send_command() and ucsi_run_command() which has led
to various locking bugs in the past.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix 2 unlocked ucsi_run_command calls:
1. ucsi_handle_connector_change() contains one ucsi_send_command() call,
which takes the ppm_lock for it; and one ucsi_run_command() call which
relies on the caller have taking the ppm_lock.
ucsi_handle_connector_change() does not take the lock, so the
second (ucsi_run_command) calls should also be ucsi_send_command().
2. ucsi_get_pdos() gets called from ucsi_handle_connector_change() which
does not hold the ppm_lock, so it also must use ucsi_send_command().
This commit also adds a WARN_ON(!mutex_is_locked(&ucsi->ppm_lock)); to
ucsi_run_command() to avoid similar problems getting re-introduced in
the future.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lockdep reports an AB BA lock inversion between ucsi_init() and
ucsi_handle_connector_change():
AB order:
1. ucsi_init takes ucsi->ppm_lock (it runs with that locked for the
duration of the function)
2. usci_init eventually end up calling ucsi_register_displayport,
which takes ucsi_connector->lock
BA order:
1. ucsi_handle_connector_change work is started, takes ucsi_connector->lock
2. ucsi_handle_connector_change calls ucsi_send_command which takes
ucsi->ppm_lock
The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().
This commit fixes the AB BA lock inversion by making ucsi_init drop the
ucsi->ppm_lock before it starts registering ports; and replacing any
ucsi_run_command() calls after this point with ucsi_send_command()
(which is a wrapper around run_command taking the lock while handling
the command).
Some of the replacing of ucsi_run_command with ucsi_send_command
in the helpers used during port registration also fixes a number of
code paths after registration which call ucsi_run_command() without
holding the ppm_lock:
1. ucsi_altmode_update_active() call in ucsi/displayport.c
2. ucsi_register_altmodes() call from ucsi_handle_connector_change()
(through ucsi_partner_change())
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 88b7381a93 ("USB: Select better matching USB drivers when
available") introduced the use of a "match" function to select a
non-generic/better driver for a particular USB device. This
unfortunately breaks the operation of usbip in general, as reported in
the kernel bugzilla with bug 208267 (linked below).
Upon inspecting the aforementioned commit, one can observe that the
original code in the usb_device_match function used to return 1
unconditionally, but the aforementioned commit makes the usb_device_match
function use identifier tables and "match" virtual functions, if either of
them are available.
Hence, this commit implements a match function for usbip that
unconditionally returns true to ensure that usbip is functional again.
This change has been verified to restore usbip functionality, with a
v5.7.y kernel on an up-to-date version of Qubes OS 4.0, which uses
usbip to redirect USB devices between VMs.
Thanks to Jonathan Dieter for the effort in bisecting this issue down
to the aforementioned commit.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208267
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1856443
Link: https://github.com/QubesOS/qubes-issues/issues/5905
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Cc: <stable@vger.kernel.org> # 5.7
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200810160017.46002-1-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lvs_rh_probe() can return some nonnegative value from usb_control_msg()
when it is less than "USB_DT_HUB_NONVAR_SIZE + 2" that is considered as
a failure. Make lvs_rh_probe() return -EINVAL in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200805090643.3432-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang static analysis reports this error
cdc-acm.c:409:3: warning: Use of memory after it is freed
acm_process_notification(acm, (unsigned char *)dr);
There are three problems, the first one is that dr is not reset
The variable dr is set with
if (acm->nb_index)
dr = (struct usb_cdc_notification *)acm->notification_buffer;
But if the notification_buffer is too small it is resized with
if (acm->nb_size) {
kfree(acm->notification_buffer);
acm->nb_size = 0;
}
alloc_size = roundup_pow_of_two(expected_size);
/*
* kmalloc ensures a valid notification_buffer after a
* use of kfree in case the previous allocation was too
* small. Final freeing is done on disconnect.
*/
acm->notification_buffer =
kmalloc(alloc_size, GFP_ATOMIC);
dr should point to the new acm->notification_buffer.
The second problem is any data in the notification_buffer is lost
when the pointer is freed. In the normal case, the current data
is accumulated in the notification_buffer here.
memcpy(&acm->notification_buffer[acm->nb_index],
urb->transfer_buffer, copy_size);
When a resize happens, anything before
notification_buffer[acm->nb_index] is garbage.
The third problem is the acm->nb_index is not reset on a
resizing buffer error.
So switch resizing to using krealloc and reassign dr and
reset nb_index.
Fixes: ea2583529c ("cdc-acm: reassemble fragmented notifications")
Signed-off-by: Tom Rix <trix@redhat.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200801152154.20683-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently dwc3 doesn't handle usb_request->zero for SG requests. This
change checks and prepares extra TRBs for the ZLP for SG requests.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The usb_request->zero doesn't apply for isoc. Also, if we prepare a
0-length (ZLP) TRB for the OUT direction, we need to prepare an extra
TRB to pad up to the MPS alignment. Use the same bounce buffer for the
ZLP TRB and the extra pad TRB.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: d6e5a549cc ("usb: dwc3: simplify ZLP handling")
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The SG list may be set up with entry size more than the requested
length. Check the usb_request->length and make sure that we don't setup
the TRBs to send/receive more than requested. This case may occur when
the SG entry is allocated up to a certain minimum size, but the request
length is less than that. It can also occur when the request is reused
for a different request length.
Cc: <stable@vger.kernel.org> # v4.18+
Fixes: a31e63b608 ("usb: dwc3: gadget: Correct handling of scattergather lists")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a memory allocation fails within a 'usb_ep_alloc_request()' call, the
already allocated memory must be released.
Fix a mix-up in the code and free the correct requests.
Fixes: c52661d60f ("usb-gadget: Initial merge of target module for UASP + BOT")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=SYqr
-----END PGP SIGNATURE-----
Merge tag 'media/v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Legacy soc_camera driver was removed from staging
- New I2C sensor related drivers: dw9768, ch7322, max9271, rdacm20
- TI vpe driver code was re-organized and had new features added
- Added Xilinx MIPI CSI-2 Rx Subsystem driver
- Added support for Infrared Toy and IR Droid devices
- Lots of random driver fixes, new features and cleanups
* tag 'media/v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (318 commits)
media: camss: fix memory leaks on error handling paths in probe
media: davinci: vpif_capture: fix potential double free
media: radio: remove redundant assignment to variable retval
media: allegro: fix potential null dereference on header
media: mtk-mdp: Fix a refcounting bug on error in init
media: allegro: fix an error pointer vs NULL check
media: meye: fix missing pm_mchip_mode field
media: cafe-driver: use generic power management
media: saa7164: use generic power management
media: v4l2-dev/ioctl: Fix document for VIDIOC_QUERYCAP
media: v4l2: Correct kernel-doc inconsistency
media: v4l2: Correct kernel-doc inconsistency
media: dvbdev.h: keep * together with the type
media: v4l2-subdev.h: keep * together with the type
media: videobuf2: Print videobuf2 buffer state by name
media: colorspaces-details.rst: fix V4L2_COLORSPACE_JPEG description
media: tw68: use generic power management
media: meye: use generic power management
media: cx88: use generic power management
media: cx25821: use generic power management
...
Here is the large set of TTY and Serial driver patches for 5.9-rc1.
Lots of bugfixes in here, thanks to syzbot fuzzing for serial and vt and
console code.
Other highlights include:
- much needed vt/vc code cleanup from Jiri Slaby
- 8250 driver fixes and additions
- various serial driver updates and feature enhancements
- locking cleanup for serial/console initializations
- other minor cleanups
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXyv30A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynW+gCgv+OqxT0jeNRAMSQcpMvP3wTBMKIAn1StfjJ4
y8uwZuQQimD49uj8XtDq
=bKSv
-----END PGP SIGNATURE-----
Merge tag 'tty-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large set of TTY and Serial driver patches for 5.9-rc1.
Lots of bugfixes in here, thanks to syzbot fuzzing for serial and vt
and console code.
Other highlights include:
- much needed vt/vc code cleanup from Jiri Slaby
- 8250 driver fixes and additions
- various serial driver updates and feature enhancements
- locking cleanup for serial/console initializations
- other minor cleanups
All of these have been in linux-next with no reported issues"
* tag 'tty-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (90 commits)
MAINTAINERS: enlist Greg formally for console stuff
vgacon: Fix for missing check in scrollback handling
Revert "serial: 8250: Let serial core initialise spin lock"
serial: 8250: Let serial core initialise spin lock
tty: keyboard, do not speculate on func_table index
serial: stm32: Add RS485 RTS GPIO control
serial: 8250_dw: Fix common clocks usage race condition
serial: 8250_dw: Pass the same rate to the clk round and set rate methods
serial: 8250_dw: Simplify the ref clock rate setting procedure
serial: 8250: Add 8250 port clock update method
tty: serial: imx: add imx earlycon driver
tty: serial: imx: enable imx serial console port as module
tty/synclink: remove leftover bits of non-PCI card support
tty: Use the preferred form for passing the size of a structure type
tty: Fix identation issues in struct serial_struct32
tty: Avoid the use of one-element arrays
serial: msm_serial: add sparse context annotation
serial: pmac_zilog: add sparse context annotation
newport_con: vc_color is now in state
serial: imx: use hrtimers for rs485 delays
...
Here is the large set of USB and Thunderbolt patches for 5.9-rc1.
Nothing really magic/major in here, just lots of little changes and
updates:
- clean up language usages in USB core and some drivers
- Thunderbolt driver updates and additions
- USB Gadget driver updates
- dwc3 driver updates (like always...)
- build with "W=1" warning fixups
- mtu3 driver updates
- usb-serial driver updates and device ids
- typec additions and updates for new hardware
- xhci debug code updates for future platforms
- cdns3 driver updates
- lots of other minor driver updates and fixes and cleanups
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXymciA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylVVwCfU7JxgjFhAJTzC9K5efVqsrSHzxQAnijHrqUn
pHgI9M1ZRVGwmv2RNWb3
=9/8I
-----END PGP SIGNATURE-----
Merge tag 'usb-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the large set of USB and Thunderbolt patches for 5.9-rc1.
Nothing really magic/major in here, just lots of little changes and
updates:
- clean up language usages in USB core and some drivers
- Thunderbolt driver updates and additions
- USB Gadget driver updates
- dwc3 driver updates (like always...)
- build with "W=1" warning fixups
- mtu3 driver updates
- usb-serial driver updates and device ids
- typec additions and updates for new hardware
- xhci debug code updates for future platforms
- cdns3 driver updates
- lots of other minor driver updates and fixes and cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (330 commits)
usb: common: usb-conn-gpio: Register charger
usb: mtu3: simplify mtu3_req_complete()
usb: mtu3: clear dual mode of u3port when disable device
usb: mtu3: use MTU3_EP_WEDGE flag
usb: mtu3: remove useless member @busy in mtu3_ep struct
usb: mtu3: remove repeated error log
usb: mtu3: add ->udc_set_speed()
usb: mtu3: introduce a funtion to check maximum speed
usb: mtu3: clear interrupts status when disable interrupts
usb: mtu3: reinitialize CSR registers
usb: mtu3: fix macro for maximum number of packets
usb: mtu3: remove unnecessary pointer checks
usb: xhci: Fix ASMedia ASM1142 DMA addressing
usb: xhci: define IDs for various ASMedia host controllers
usb: musb: convert to devm_platform_ioremap_resource_byname
usb: gadget: tegra-xudc: convert to devm_platform_ioremap_resource_byname
usb: gadget: r8a66597: convert to devm_platform_ioremap_resource_byname
usb: dwc3: convert to devm_platform_ioremap_resource_byname
usb: cdns3: convert to devm_platform_ioremap_resource_byname
usb: phy: am335x: convert to devm_platform_ioremap_resource_byname
...
- Prepare for tasklet API modernization (Romain Perier, Allen Pais, Kees Cook)
-----BEGIN PGP SIGNATURE-----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=hb+e
-----END PGP SIGNATURE-----
Merge tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull tasklets API update from Kees Cook:
"These are the infrastructure updates needed to support converting the
tasklet API to something more modern (and hopefully for removal
further down the road).
There is a 300-patch series waiting in the wings to get set out to
subsystem maintainers, but these changes need to be present in the
kernel first. Since this has some treewide changes, I carried this
series for -next instead of paining Thomas with it in -tip, but it's
got his Ack.
This is similar to the timer_struct modernization from a while back,
but not nearly as messy (I hope). :)
- Prepare for tasklet API modernization (Romain Perier, Allen Pais,
Kees Cook)"
* tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
tasklet: Introduce new initialization API
treewide: Replace DECLARE_TASKLET() with DECLARE_TASKLET_OLD()
usb: gadget: udc: Avoid tasklet passing a global
These are mostly cosmetic changes and minor bugfixes for the SoC
specific code, across the 32-bit at91, mvebu, davinci, samsung, and
omap platforms.
The main notable changes are for the Samsung Exynos platform, which
sees a rewrite of gpio handling and a change to restore and adds
a workaround for a problem with cpuidle support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=IHpg
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"These are mostly cosmetic changes and minor bugfixes for the SoC
specific code, across the 32-bit at91, mvebu, davinci, samsung, and
omap platforms.
The main notable changes are for the Samsung Exynos platform, which
sees a rewrite of gpio handling and a change to restore and adds a
workaround for a problem with cpuidle support"
* tag 'arm-soc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: socfpga: PM: add missing put_device() call in socfpga_setup_ocram_self_refresh()
MAINTAINERS: arm/amlogic: add designated reviewers
ARM: davinci: dm646x-evm: Simplify error handling in 'evm_sw_setup()'
ARM: davinci: Fix trivial spelling
ARM: davinci: Replace HTTP links with HTTPS ones
ARM: s3c24xx: Replace HTTP links with HTTPS ones
ARM: orion/gpio: Make use of for_each_requested_gpio()
ARM: at91: Replace HTTP links with HTTPS ones
ARM: at91: pm: add missing put_device() call in at91_pm_sram_init()
ARM: rpc: Change blacklist to quirklist in ecode.c file
ARM: OMAP: Replace HTTP links with HTTPS ones
ARM: s3c24xx: leds: Convert to use GPIO descriptors
udc: lpc32xx: mark local function static
ARM: exynos: MCPM: Restore big.LITTLE cpuidle support
ARM: exynos: clear L310_AUX_CTRL_FULL_LINE_ZERO in default l2c_aux_val
