The kernel does not properly clear the EBIU Error Master (EBIU_ERRMST) Register
on BF548, which causes the kernel to panic.
We need to make sure that we clear the EBIU_ERRMST (necessary on BF54x)
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
a global _sys_trace will cause the assembler to fail, it should be fixed in toolchain side firstly.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Apply ANOMALY_05000283 & ANOMALY_05000315
Workaround also to the EXCEPTION path.
Cover evt_ivhw also with ANOMALY_05000315
The Workaround needs to be prior to accesses (either read or write) to
any system MMR.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- remove cheesy read_iloc() function
- move invalidate_entire_icache function to lock.S
- export proper prototypes for functions in lock.S
- only build lock.S when BFIN_ICACHE_LOCK is enabled
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- Disable all bits in SIC_IWR unless we are going into a real (DPMC)
power saving mode. Any Interrupt can wake the core form it's idle state.
- Remove deep sleep mode as it is not going to be used anywhere:
We support sleep, sleep deeper and hibernate.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- Skip single step if global interrupt disable bit is set.
- Extend bernds' patch r4673 to skip single step in any interrupt entry
that interrupts the code which is under single stepping. Bernds' patch
only allow user space single stepping.
Singed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Skip single step if event priority of current instruction is higher than
that of the first instruction, from which gdb starts single step.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Enable: PM_SUSPEND_MEM -> Blackfin Hibernate to SDRAM
This feature requires a special bootloader (u-boot)
supporting return from hibernate.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
use kernel command line mem and max_mem bootargs to limit
availabe memory instead.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
When transferring to IRQ5 from an exception, save SYSCFG in memory across the
transfer and clear the trace bit.
When we get a single step exception, check whether we can safely clear the
trace bit in SYSCFG. We can (and should) clear it after the first instruction
of the interrupt handler; the first insn saves SYSCFG to the stack in all
handlers.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
In the double fault handler, set up the PT_RETI slot so that
we print out the correct return address in the dumping code.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Remove the circular buffering mechanism for exceptions. Instead, point RETX
at a safe location from which to fetch three NOPs.
This safe location is now in the fixed code area, and also used for certain
anomaly workarounds, to ensure that user space can find a valid ICPLB when
things are built with CONFIG_MPU.
Also, save I/DCPLB_FAULT_ADDRESS when lowering to level 5, since the hardware
reg is valid only at exception level.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The irq setup code no longer calls gpio request and free.
This patch also changes the default gpio_free behavior on Blackfin.
A freed GPIO keeps it's last state, and is not defaulted back to
an input. This is also what all other architectures do.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
detect the memory available in the system on the fly by default
rather than forcing people to set this manually in the kconfig
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
There were a couple of problems with the way the trace buffer state
is saved/restored in assembly. The DEBUG_HWTRACE_SAVE/RESTORE macros
save a value to the stack, which is not immediately obvious; the CPLB
exception code needed changes to load the correct value of the stack
pointer. The other problem is that the SAVE/RESTORE macros weren't
pushing and popping the value downwards on the stack, but rather moving
it _upwards_, which is of course completely broken.
We also need to make sure there's a matching DEBUG_HWTRACE_RESTORE in
the error case of the CPLB handler.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
