The check that queue is less or equal to zero is always true
because queue is a u32; queue is decremented and will wrap around
and never go -ve. Fix this by making queue an int.
Detected by CoverityScan, CID#1428988 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_tso_allocator can fail to set the Last Descriptor bit
on a descriptor that actually was the last descriptor.
This happens when the buffer of the last descriptor ends
up having a size of exactly TSO_MAX_BUFF_SIZE.
When the IP eventually reaches the next last descriptor,
which actually has the bit set, the DMA will hang.
When the DMA hangs, we get a tx timeout, however,
since stmmac does not do a complete reset of the IP
in stmmac_tx_timeout, we end up in a state with
completely hung TX.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethoc_reset enables device interrupts, ethoc_interrupt may schedule a
NAPI poll before NAPI is enabled in the ethoc_open, which results in
device being unable to send or receive anything until it's closed and
reopened. In case the device is flooded with ingress packets it may be
unable to recover at all.
Move napi_enable above ethoc_reset in the ethoc_open to fix that.
Fixes: a170285772 ("net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current comparison of entry < 0 will never be true since entry is an
unsigned integer. Make entry an int to ensure -ve error return values
from the call to jumbo_frm are correctly being caught.
Detected by CoverityScan, CID#1238760 ("Macro compares unsigned to 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In f8b45b74cc ("i40e/i40evf: Use build_skb to build frames")
i40e_build_skb updates the page_offset field with an incorrect offset,
which can lead to data corruption. This patch updates page_offset
correctly, by properly setting truesize.
Note that the bug only appears on architectures where PAGE_SIZE is
8192 or larger.
Fixes: f8b45b74cc ("i40e/i40evf: Use build_skb to build frames")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 0da36b9774 ("i40e: use DECLARE_BITMAP for state fields")
introduced changes in the way i40e works with state flags converting
them to bitmaps using kernel bitmap API. This change introduced a
regression due to a mistaken substitution using __I40E_VSI_DOWN instead
of __I40E_DOWN when testing state of a PF at i40e_reset_subtask()
function. This caused a flood in the kernel log with the follow message:
[49.013] i40e 0002:01:00.0: bad reset request 0x00000020
Commit d19cb64b92 ("i40e: separate PF and VSI state flags")
also introduced some misuse of the VSI and PF flags, so both could be
considered as the offenders.
This patch simply fixes the flags where it makes sense by changing
__I40E_VSI_DOWN to __I40E_DOWN.
Fixes: 0da36b9774 ("i40e: use DECLARE_BITMAP for state fields")
Fixes: d19cb64b92 ("i40e: separate PF and VSI state flags")
Reviewed-by: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Granular QoS per VF feature must be enabled in FW before it can be
used.
Thus, the driver cannot modify a QP's qos_vport value (via the UPDATE_QP FW
command) if the feature has not been enabled -- the FW returns an error if
this is attempted.
Fixes: 08068cd568 ("net/mlx4: Added qos_vport QP configuration in VST mode")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our previous patch (cited below) introduced a regression
for RAW Eth QPs.
Fix it by checking if the QP number provided by user-space
exists, hence allowing steering rules to be added for valid
QPs only.
Fixes: 89c557687a ("net/mlx4_en: Avoid adding steering rules with invalid ring")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xgbe_map_rx_buffer is rather confused about what PAGE_ALLOC_COSTLY_ORDER
means. It uses PAGE_ALLOC_COSTLY_ORDER-1 assuming that
PAGE_ALLOC_COSTLY_ORDER is the first costly order which is not the case
actually because orders larger than that are costly. And even that
applies only to sleeping allocations which is not the case here. We
simply do not perform any costly operations like reclaim or compaction
for those. Simplify the code by dropping the order calculation and use
PAGE_ALLOC_COSTLY_ORDER directly.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use software polling (PHY_POLL) to check for link state changes instead
of relying on the EMAC's hardware polling feature. Some PHY drivers
are unable to get a functioning link because the HW polling is not
robust enough.
The EMAC is able to poll the PHY on the MDIO bus looking for link state
changes (via the Link Status bit in the Status Register at address 0x1).
When the link state changes, the EMAC triggers an interrupt and tells the
driver what the new state is. The feature eliminates the need for
software to poll the MDIO bus.
Unfortunately, this feature is incompatible with phylib, because it
ignores everything that the PHY core and PHY drivers are trying to do.
In particular:
1. It assumes a compatible register set, so PHYs with different registers
may not work.
2. It doesn't allow for hardware errata that have work-arounds implemented
in the PHY driver.
3. It doesn't support multiple register pages. If the PHY core switches
the register set to another page, the EMAC won't know the page has
changed and will still attempt to read the same PHY register.
4. It only checks the copper side of the link, not the SGMII side. Some
PHY drivers (e.g. at803x) may also check the SGMII side, and
report the link as not ready during autonegotiation if the SGMII link
is still down. Phylib then waits for another interrupt to query
the PHY again, but the EMAC won't send another interrupt because it
thinks the link is up.
Cc: stable@vger.kernel.org # 4.11.x
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qlogic's 82xx series adapter doesn't support
tunnel offloads, driver incorrectly assumes that it is
supported and causes firmware hang while running tunnel IO.
This patch fixes this by not advertising tunnel offloads
for 82xx adapters.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original author left the project and so far has not
responded to emails sent to the listed address.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NETDEV WATCHDOG timeout on startup by adding missing register
writes that properly setup SGMII.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take uld mutex to avoid race between cxgb_up() and
cxgb4_register_uld() to enable napi for the same uld
queue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SYSTEMPORT Lite, since we have the main interrupt source in the first
cell, the second cell is the Wake-on-LAN interrupt, yet the code was not
properly updated to fetch the second cell, and instead looked at the
third and non-existing cell for Wake-on-LAN.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently multi-cos isn't working for bnx2x quite some time -
driver implements ndo_select_queue() to allow queue-selection
for FCoE, but the regular L2 flow would cause it to modulo the
fallback's result by the number of queues.
The fallback would return a queue matching the needed tc
[via __skb_tx_hash()], but since the modulo is by the number of TSS
queues where number of TCs is not accounted, transmission would always
be done by a queue configured into using TC0.
Fixes: ada7c19e6d ("bnx2x: use XPS if possible for bnx2x_select_queue instead of pure hash")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.16.45.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver may sleep under a write spin lock, and the function
call path is:
qlcnic_82xx_hw_write_wx_2M (acquire the lock by write_lock_irqsave)
crb_win_lock
qlcnic_pcie_sem_lock
usleep_range
qlcnic_82xx_hw_read_wx_2M (acquire the lock by write_lock_irqsave)
crb_win_lock
qlcnic_pcie_sem_lock
usleep_range
To fix it, the usleep_range is replaced with udelay.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NULL check before dereferencing pointer _id_ in order to avoid
a potential NULL pointer dereference.
Addresses-Coverity-ID: 1397995
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building the driver with CONFIG_SMP disabled results in a harmless
warning:
ethernet/mellanox/mlx5/core/main.c: In function 'mlx5_irq_set_affinity_hint':
ethernet/mellanox/mlx5/core/main.c:615:6: error: unused variable 'irq' [-Werror=unused-variable]
It's better to express the conditional compilation using IS_ENABLED()
here, as that lets the compiler see what the intented use for the variable
is, and that it can be silently discarded.
Fixes: b665d98edc ("net/mlx5: Tolerate irq_set_affinity_hint() failures")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation lacks the logic for providing management
firmware with RDMA-related statistics; [much] worse than that -
it logs such events by default to system logs.
Since the statistics' gathering is done periodically, using sufficiently
new management firmware the system logs would get filled with these
unnecessary prints.
For now, reduce the verbosity of the log so that it would not be
logged by default.
Fixes: 6c75424612 ("qed: Add support for NCSI statistics")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PCI error recovery process, specifically on eeh_err_detected()
we might have a NULL netdev struct, hence a direct dereference will
lead to a kernel oops. This was observed with latest upstream kernel
(v4.12-rc2) on Chelsio adapter T422-CR in PowerPC machines.
This patch checks for NULL pointer and avoids the crash, both in
eeh_err_detected() and eeh_resume(). Also, we avoid to trigger
a fatal error or to try disabling interrupts on FW during PCI
error recovery, because: (a) driver might not be able to accurately
access PCI regions in this case, and (b) trigger a fatal error
_during_ the recovery steps is a mistake that could prevent the
recovery path to complete successfully.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ax_init_dev (which is called only from the driver's .probe
function) calls free_irq in the error path without having requested the
irq in the first place. So drop the free_irq call in the error path.
Fixes: 825a2ff189 ("AX88796 network driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least some of the be2net cards do not seem to be capabled
of performing checksum offload computions on Q-in-Q packets.
In these case, the recevied checksum on the remote is invalid
and TCP syn packets are dropped.
This patch adds a call to check disbled acceleration features
on Q-in-Q tagged traffic.
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some TC offloads fixes from Or Gerlitz.
From Erez, mlx5 IPoIB RX fix to improve GRO.
From Mohamad, Command interface fix to improve mitigation against FW
commands timeouts.
From Tariq, Driver load Tolerance against affinity settings failures.
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZJD6WAAoJEEg/ir3gV/o+EJkH+gN9G9jXCkYEkuy0eADCRRMY
Zs1wkJory1whkMyLScA8xO13IpSZ8AmZCp53hPi+Ak17JQrQ26D9MlzkR3WelWL4
4ABZBRDapKdFNsY2SSnGWb7U1INqCmamHF9hOIcezk6rPxKdx9RQ2pkShM5fObKL
vSi+ptrUd5KuMWjikKr/P0v8BfFGYhDTcS5ToNFcITDrbs9srXRjMzgM0MFtvWit
9chXJVpudJdb9vlHjYrlY1nuJopfXyJxtvfBZqjQmviA/+LT0qJ81qkBEjaEyjxk
10Nc6eYfuZKIiDav3AC69xuSTPk73dxrrhOEBpPdqaq6sEOFl8NjpidETYVBnwQ=
=GMLr
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2017-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-fixes-2017-05-23
Some TC offloads fixes from Or Gerlitz.
From Erez, mlx5 IPoIB RX fix to improve GRO.
From Mohamad, Command interface fix to improve mitigation against FW
commands timeouts.
From Tariq, Driver load Tolerance against affinity settings failures.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY require to wait for a bit after the reset GPIO has been
toggled. This adds support for the DT property `phy-reset-post-delay`
which gives the delay in milliseconds to wait after reset.
If the DT property is not given, no delay is observed. Post reset delay
greater than 1000ms are invalid.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tolerance to failures of irq_set_affinity_hint().
Its role is to give hints that optimizes performance,
and should not block the driver load.
In non-SMP systems, functionality is not available as
there is a single core, and all these calls definitely
fail. Hence, do not call the function and avoid the
warning prints.
Fixes: db058a186f ("net/mlx5_core: Set irq affinity hints")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently when firmware command gets stuck or it takes long time to
complete, the driver command will get timeout and the command slot is
freed and can be used for new commands, and if the firmware receive new
command on the old busy slot its behavior is unexpected and this could
be harmful.
To fix this when the driver command gets timeout we return failure,
but we don't free the command slot and we wait for the firmware to
explicitly respond to that command.
Once all the entries are busy we will stop processing new firmware
commands.
Fixes: 9cba4ebcf3 ('net/mlx5: Fix potential deadlock in command mode change')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
IPoIB packet contains the pseudo header area, we need to pull it prior
to reset_mac_header in order to let the GRO work well.
In more details:
GRO checks the mac address of the new coming packet, it does that by
comparing the hard_header_len size of the current packet to the previous
one in that session, the comparison is over hard_header_len size.
Now, the driver prepares that area in the skb by allocating area from the
reserved part and resetting the correct mac header to it.
Fixes: 9d6bd752c6 ("net/mlx5e: IPoIB, RX handler")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The sparse tool emits these correct complaints:
drivers/net/ethernet/mellanox/mlx5/core//en_tc.c:1005:25: warning: cast to restricted __be32
drivers/net/ethernet/mellanox/mlx5/core//en_tc.c:1007:25: warning: cast to restricted __be16
The value is provided from user-space in network order, but there's
no way for them to realize that, avoid the warnings by casting to the
appropriate type.
Fixes: d79b6df6b1 ('net/mlx5e: Add parsing of TC pedit actions to HW format')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we don't support partial header re-writes through TC pedit
action offloading. However, the code that enforces that wasn't err-ing
on cases where the first and last bits of the mask are set but there is
some zero bit between them, such as in the below example, fix that!
tc filter add dev enp1s0 protocol ip parent ffff: prio 10 flower
ip_proto udp dst_port 2001 skip_sw
action pedit munge ip src set 1.0.0.1 retain 0xff0000ff
Fixes: d79b6df6b1 ('net/mlx5e: Add parsing of TC pedit actions to HW format')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When offloading header re-writes, the HW re-calculates the relevant L3/L4
checksums. Hence, when upper layers (as done by OVS) ask for TC checksum action
offload together with pedit offload, don't err. This command now works:
tc filter add dev ens1f0 protocol ip parent ffff: prio 20 flower skip_sw
ip_proto tcp dst_port 9001
action pedit ex munge tcp dport set 0x1234 pipe
action csum tcp
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We wrongly direcly invoke hlist_del_rcu() and not hash_del_rcu() which
does a slightly different call now and may change later, fix that.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If dma mask checks fail in atl2_probe(), it breaks off initialization,
deallocates all resources, but returns zero.
The patch adds proper error code return value and
make error code setup unified.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we got an FDB notification for a port that doesn't exist we
execute an FDB entry delete to prevent it from re-appearing the next
time we poll for notifications.
If the operation failed we would trigger a NULL pointer dereference as
'mlxsw_sp_port' is NULL.
Fix it by reporting the error using the underlying bus device instead.
Fixes: 12f1501e75 ("mlxsw: spectrum: remove FDB entry in case we get unknown object notification")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EPROBE_DEFER is not an error, hence printing an error message like
sh-eth ee700000.ethernet: failed to initialise MDIO
may confuse the user.
To fix this, suppress the error message in case of probe deferral.
While at it, shorten the message, and add the actual error code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO initialization failure message is printed using the network
device, before it has been registered, leading to:
(null): failed to initialise MDIO
Use the platform device instead to fix this:
sh-eth ee700000.ethernet: failed to initialise MDIO
Fixes: daacf03f0b ("sh_eth: Register MDIO bus before registering the network device")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During rif counter freeing the counter index can be invalid. Add check
of validity before freeing the counter.
Fixes: e0c0afd8aa ("mlxsw: spectrum: Support for counters on router interfaces")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of disabled counters the entry index will be incorrect. Fix this
by moving the entry index set before the counter status check.
Fixes: 2ba5999f00 ("mlxsw: spectrum: Add Support for erif table entries access")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.16.43.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, all the host based DCBX settings from lldpad will fail if the
firmware DCBX agent is running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, bnxt_dcb_init() is called too early before we
determine if the firmware DCBX agent is running or not. As a result,
we are not setting the DCB_CAP_DCBX_HOST and DCB_CAP_DCBX_LLD_MANAGED
flags properly to report to DCBNL.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now reference the arp_tbl, which requires IPv4 support to be
enabled in the kernel, otherwise we get a link error:
drivers/net/built-in.o: In function `mlx5e_tc_update_neigh_used_value':
(.text+0x16afec): undefined reference to `arp_tbl'
drivers/net/built-in.o: In function `mlx5e_rep_neigh_init':
en_rep.c:(.text+0x16c16d): undefined reference to `arp_tbl'
drivers/net/built-in.o: In function `mlx5e_rep_netevent_event':
en_rep.c:(.text+0x16cbb5): undefined reference to `arp_tbl'
This adds a Kconfig dependency for it.
Fixes: 232c001398 ("net/mlx5e: Add support to neighbour update flow")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Track alignment in BPF verifier so that legitimate programs won't be
rejected on !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS architectures.
2) Make tail calls work properly in arm64 BPF JIT, from Deniel
Borkmann.
3) Make the configuration and semantics Generic XDP make more sense and
don't allow both generic XDP and a driver specific instance to be
active at the same time. Also from Daniel.
4) Don't crash on resume in xen-netfront, from Vitaly Kuznetsov.
5) Fix use-after-free in VRF driver, from Gao Feng.
6) Use netdev_alloc_skb_ip_align() to avoid unaligned IP headers in
qca_spi driver, from Stefan Wahren.
7) Always run cleanup routines in BPF samples when we get SIGTERM, from
Andy Gospodarek.
8) The mdio phy code should bring PHYs out of reset using the shared
GPIO lines before invoking bus->reset(). From Florian Fainelli.
9) Some USB descriptor access endian fixes in various drivers from
Johan Hovold.
10) Handle PAUSE advertisements properly in mlx5 driver, from Gal
Pressman.
11) Fix reversed test in mlx5e_setup_tc(), from Saeed Mahameed.
12) Cure netdev leak in AF_PACKET when using timestamping via control
messages. From Douglas Caetano dos Santos.
13) netcp doesn't support HWTSTAMP_FILTER_ALl, reject it. From Miroslav
Lichvar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
ldmvsw: stop the clean timer at beginning of remove
ldmvsw: unregistering netdev before disable hardware
net: netcp: fix check of requested timestamping filter
ipv6: avoid dad-failures for addresses with NODAD
qed: Fix uninitialized data in aRFS infrastructure
mdio: mux: fix device_node_continue.cocci warnings
net/packet: fix missing net_device reference release
net/mlx4_core: Use min3 to select number of MSI-X vectors
macvlan: Fix performance issues with vlan tagged packets
net: stmmac: use correct pointer when printing normal descriptor ring
net/mlx5: Use underlay QPN from the root name space
net/mlx5e: IPoIB, Only support regular RQ for now
net/mlx5e: Fix setup TC ndo
net/mlx5e: Fix ethtool pause support and advertise reporting
net/mlx5e: Use the correct pause values for ethtool advertising
vmxnet3: ensure that adapter is in proper state during force_close
sfc: revert changes to NIC revision numbers
net: ch9200: add missing USB-descriptor endianness conversions
net: irda: irda-usb: fix firmware name on big-endian hosts
net: dsa: mv88e6xxx: add default case to switch
...
Stop the clean timer earlier to be sure there's no asynchronous
interference while stopping the port.
Orabug: 25748241
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running LDom binding/unbinding test, kernel may panic
in ldmvsw_open(). It is more likely that because we're removing
the ldc connection before unregistering the netdev in vsw_port_remove(),
we set up a window of time where one process could be removing the
device while another trying to UP the device. This also sometimes causes
vio handshake error due to opening a device without closing it completely.
We should unregister the netdev before we disable the "hardware".
Orabug: 25980913, 25925306
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't support timestamping of all received packets and
should return error when trying to enable the HWTSTAMP_FILTER_ALL
filter.
Cc: WingMan Kwok <w-kwok2@ti.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Misc fixes for mlx5 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZGDM8AAoJEEg/ir3gV/o+svMH/1lAl+FIGCWgZ82/UbFHCZCW
SIXEnP2id+Nic7JxQSa/RVQ43I75wkM8pN929hFoyz8p/pPLhZkpo7vX6yLWG2SL
fTx/4Qn5jR/eow/D+fdrlyKMPg0A7fijY+ZnvDPsQkjtakIedCgc/A1xDufpKi7+
I7nOJa4yACuZK0gzy32VGgpJw02q32eRTJjKHRiEYdmNQSIJpmRbG2m4e0z/me2s
hrMt358/llPOZNwkAPD2SHZxH68oSq5EbSRmz5jDwXfTVFkjWNQVowwm3pCFjsQn
3xDtkjakVPVBUagR3hngtLPcsDpUR4GU3tHr4l/UPp0wFBXVKgdupC7B+mCkSp4=
=ubJG
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2017-05-12-V2' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-05-12
This series contains some mlx5 fixes for net.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5e: Fix ethtool pause support and advertise reporting") kernels >= 4.8
("net/mlx5e: Use the correct pause values for ethtool advertising") kernels >= 4.8
v1->v2:
Dropped statistics spinlock patch, it needs some extra work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
