The only thing reset_long_term_buff() should do is set
buffer to zero. After doing that, it is not necessary to
send_request_map again to VIOS since it actually does not
change the mapping. So, keep memset function and remove all
others.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mptcpi_local_addr_used and mptcpi_local_addr_max in struct mptcp_info.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that the right argument to be passed is &tcp_ip6_spec->ip6dst,
not &tcp_ip6_spec->ip6src, when calling function ipv6_addr_any().
Addresses-Coverity-ID: 1501734 ("Copy-paste error")
Fixes: efca91e89b ("i40e: Add flow director support for IPv6")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware comes up with default max frame size set to 1518. When using it
with switch it results in actual Ethernet MTU 1492:
1518 - 14 (Ethernet header) - 4 (Broadcom's tag) - 4 (802.1q) - 4 (FCS)
Above means hardware in its default state can't handle standard Ethernet
traffic (MTU 1500).
Define maximum possible Ethernet overhead and always set MAC max frame
length accordingly. This change fixes handling Ethernet frames of length
1506 - 1514.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nobuhiro Iwamatsu says:
====================
net: stmmac: Add Toshiba Visconti SoCs glue driver
This series is the ethernet driver for Toshiba's ARM SoC, Visconti[0].
This provides DT binding documentation, device driver, MAINTAINER files,
and updates to DT files.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ethernet controller node in Toshiba Visconti5 SoC-specific DT file.
And enable this node in TMPV7708 RM main board's board-specific DT file.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entries for Toshiba Visconti ethernet controller binding and driver.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dwmac-visconti to the stmmac driver in Toshiba Visconti ARM SoCs.
This patch contains only the basic function of the device. There is no
clock control, PM, etc. yet. These will be added in the future.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree bindings for ethernet controller of Toshiba Visconti
TMPV7700 SoC series.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
With MTU less than 1500B on all ports, the driver uses per CPU pool mode.
If one of the ports set to jumbo frame MTU size, all ports move
to shared pools mode.
Here, buffer manager TX Flow Control reconfigured on all ports.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1KB is enough for loopback port, so 2KB can be distributed
between other ports.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver has a limitation, extensively described under
Documentation/networking/dsa/sja1105.rst and
Documentation/networking/devlink/sja1105.rst, which says that when the
ports are under a bridge with vlan_filtering=1, traffic to and from
the network stack is not possible, unless the driver-specific
best_effort_vlan_filtering devlink parameter is enabled.
For users, this creates a 'wtf' moment. They need to go to the
documentation and find about the existence of this property, then maybe
install devlink and set it to true.
Having best_effort_vlan_filtering enabled by the kernel by default
delays that 'wtf' moment (maybe up to the point that it never even
happens). The user doesn't need to care that the driver supports
addressing the ports individually by retagging VLAN IDs until he/she
needs to use more than 32 VLAN IDs (since there can be at most 32
retagging rules). Only then do they need to think whether they need the
full VLAN table, at the expense of no individual port addressing, or
not.
But the odds that an sja1105 user will need more than 32 VLANs
terminated by the CPU is probably low. And, if we were to follow the
principle that more advanced use cases should require more advanced
preparation steps, then it makes more sense for ping to 'just work'
while CPU termination of > 32 VLAN IDs to require a bit more forethought
and possibly a driver-specific devlink param.
So we should be able to safely change the default here, and make this
driver act just a little bit more sanely out of the box.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My prior cleanup missed that tcp_data_ready() has to look at SOCK_DONE.
Otherwise, an application using SO_RCVLOWAT will not get EPOLLIN event
if a FIN is received in the middle of expected payload.
The reason SOCK_DONE is not examined in tcp_epollin_ready()
is that tcp_poll() catches the FIN because tcp_fin()
is also setting RCV_SHUTDOWN into sk->sk_shutdown
Fixes: 05dc72aba3 ("tcp: factorize logic into tcp_epollin_ready()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Wei Wang <weiwan@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Fix buggy brport flags offload for SJA1105 DSA
While testing the "Software fallback for bridging in DSA" on sja1105, I
discovered that I managed to introduce two bugs in a single patch
submitted recently to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The prototype of br_vlan_filter_toggle was updated to include a netlink
extack, but the stub definition wasn't, which results in a build error
when CONFIG_BRIDGE_VLAN_FILTERING=n.
Fixes: 9e781401cb ("net: bridge: propagate extack through store_bridge_parm")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev_port_attr_set function prototype was updated only for the
case where CONFIG_SWITCHDEV=y|m, leaving a prototype mismatch with the
stub definition for the disabled case. This results in a build error, so
update that function too.
Fixes: dcbdf1350e ("net: bridge: propagate extack through switchdev_port_attr_set")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch is confused by the fact that a 32-bit BIT(port) macro is passed
as argument to the ocelot_ifh_set_dest function and warns:
ocelot_xmit() warn: should '(((1))) << (dp->index)' be a 64 bit type?
seville_xmit() warn: should '(((1))) << (dp->index)' be a 64 bit type?
The destination port mask is copied into a 12-bit field of the packet,
starting at bit offset 67 and ending at 56.
So this DSA tagging protocol supports at most 12 bits, which is clearly
less than 32. Attempting to send to a port number > 12 will cause the
packing() call to truncate way before there will be 32-bit truncation
due to type promotion of the BIT(port) argument towards u64.
Therefore, smatch's fears that BIT(port) will do the wrong thing and
cause unexpected truncation for "port" values >= 32 are unfounded.
Nonetheless, let's silence the warning by explicitly passing an u64
value to ocelot_ifh_set_dest, such that the compiler does not need to do
a questionable type promotion.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Armin reported that after referenced commit his RTL8105e is dead when
resuming from suspend and machine runs on battery. This patch has been
confirmed to fix the issue.
Fixes: e80bd76fbf ("r8169: work around power-saving bug on some chip versions")
Reported-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Chulski says:
====================
net: mvpp2: Minor non functional driver code improvements
The patch series contains minor code improvements and did not change any functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
GENCONF_CTRL0_PORTX naming improved.
Non functional change.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PTR_ERR_OR_ZERO instead of IS_ERR and PTR_ERR.
Non functional change.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use >= MVPP22 instead of != MVPP21.
Non functional change.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2.1 contain 0 in Version ID register, priv->hw_version check
can be removed.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Propagate extack for switchdev VLANs from DSA
This series moves the restriction messages printed by the DSA core, and
by some individual device drivers, into the netlink extended ack
structure, to be communicated to user space where possible, or still
printed to the kernel log from the bridge layer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers can't dynamically change the VLAN filtering option, or
impose some restrictions, it would be nice to propagate this info
through netlink instead of printing it to a kernel log that might never
be read. Also netlink extack includes the module that emitted the
message, which means that it's easier to figure out which ones are
driver-generated errors as opposed to command misuse.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to communicate their restrictions to user space directly,
instead of printing to the kernel log. Where the conversion would have
been lossy and things like VLAN ID could no longer be conveyed (due to
the lack of support for printf format specifier in netlink extack), I
chose to keep the messages in full form to the kernel log only, and
leave it up to individual driver maintainers to move more messages to
extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The benefit is the ability to propagate errors from switchdev drivers
for the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING and
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL attributes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge sysfs interface stores parameters for the STP, VLAN,
multicast etc subsystems using a predefined function prototype.
Sometimes the underlying function being called supports a netlink
extended ack message, and we ignore it.
Let's expand the store_bridge_parm function prototype to include the
extack, and just print it to console, but at least propagate it where
applicable. Where not applicable, create a shim function in the
br_sysfs_br.c file that discards the extra function argument.
This patch allows us to propagate the extack argument to
br_vlan_set_default_pvid, br_vlan_set_proto and br_vlan_filter_toggle,
and from there, further up in br_changelink from br_netlink.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is identical with br_vlan_filter_toggle.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
PTP for DSA tag_ocelot_8021q
Changes in v2:
Add stub definition for ocelot_port_inject_frame when switch driver is
not compiled in.
This is part two of the errata workaround begun here:
https://patchwork.kernel.org/project/netdevbpf/cover/20210129010009.3959398-1-olteanv@gmail.com/
Now that we have basic traffic support when we operate the Ocelot DSA
switches without an NPI port, it would be nice to regain some of the
features lost due to the lack of the NPI port functionality. An
important one is PTP timestamping, which is intimately tied to the DSA
frame header added by the NPI port: on TX, we put a "timestamp request
ID" in the Injection Frame Header, while on RX, the Extraction Frame
Header contains a partial 32-bit PTP timestamp. Get rid of the NPI port
and replace it with a VLAN-based tagger, and you lose PTP, right?
Well, not quite, this is what this patch series is about. The NPI port
is basically a regular Ethernet port configured to service the packets
in and out of the switch's CPU port module (which has other non-DSA I/O
mechanisms too, such as register-based MMIO and DMA). If we disable the
NPI port, we can in theory still access the packets delivered to the CPU
port module by doing exactly what the ocelot switchdev driver does:
extracting Ethernet packets through registers (yes, it is as icky as it
sounds).
However, there's a catch. The Felix switch was integrated into NXP
LS1028A with the idea in mind that it will operate as DSA, i.e. using
the CPU port module connected to the NPI port, not having I/O over
register-based MMIO which is painfully slow and CPU intensive. So
register-based packet I/O not supposed to work - those registers aren't
even documented in the hardware reference manual for Felix. However
they kinda do, with the exception of the fact that an RX interrupt was
really not wired to the CPU cores - so we don't know when the CPU port
module receives a new packet. But we can hack even around that, by
replicating every packet that goes to the CPU port module and making it
also go to a plain internal Ethernet port. Then drop the Ethernet packet
and read the other copy of it from the CPU port module, this time
annotated with the much-wanted RX timestamp.
This is all fine and it works, but it does raise some questions about
what DSA even is anymore, if we start having switches that inject some
of their packets over Ethernet and some through registers, where do we
draw the line. In principle I believe these concerns are founded, but at
the same time, the way that the Felix driver uses register MMIO based
packet I/O is fundamentally the same as any other DSA driver capable of
PTP makes use of a side-channel for timestamps like a FIFO (just that
this one is a lot more complicated, and comes with the entire actual
packet, not just the timestamp).
Nonetheless, I tried to keep the extra pressure added by this ERR
workaround upon the DSA subsystem as small as possible, so some of the
patches are just a revisit of some of Andrew's complaints w.r.t. the
fact that tag_ocelot already violates any driver <-> tagger boundary,
and as a consequence, is not able to be used on testbeds such as
dsa_loop (which it now can). So now, the tag_ocelot and tag_ocelot_8021q
drivers should be dsa_loop-clean, and have the ERR workarounds as
self-contained as possible, using all the designated features for PTP
timestamping and nothing more.
Comments appreciated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For TX timestamping, we use the felix_txtstamp method which is common
with the regular (non-8021q) ocelot tagger. This method says that skb
deferral is needed, prepares a timestamp request ID, and puts a clone of
the skb in a queue waiting for the timestamp IRQ.
felix_txtstamp is called by dsa_skb_tx_timestamp() just before the
tagger's xmit method. In the tagger xmit, we divert the packets
classified by dsa_skb_tx_timestamp() as PTP towards the MMIO-based
injection registers, and we declare them as dead towards dsa_slave_xmit.
If not PTP, we proceed with normal tag_8021q stuff.
Then the timestamp IRQ fires, the clone queued up from felix_txtstamp is
matched to the TX timestamp retrieved from the switch's FIFO based on
the timestamp request ID, and the clone is delivered to the stack.
On RX, thanks to the VCAP IS2 rule that redirects the frames with an
EtherType for 1588 towards two destinations:
- the CPU port module (for MMIO based extraction) and
- if the "no XTR IRQ" workaround is in place, the dsa_8021q CPU port
the relevant data path processing starts in the ptp_classify_raw BPF
classifier installed by DSA in the RX data path (post tagger, which is
completely unaware that it saw a PTP packet).
This time we can't reuse the same implementation of .port_rxtstamp that
also works with the default ocelot tagger. That is because felix_rxtstamp
is given an skb with a freshly stripped DSA header, and it says "I don't
need deferral for its RX timestamp, it's right in it, let me show you";
and it just points to the header right behind skb->data, from where it
unpacks the timestamp and annotates the skb with it.
The same thing cannot happen with tag_ocelot_8021q, because for one
thing, the skb did not have an extraction frame header in the first
place, but a VLAN tag with no timestamp information. So the code paths
in felix_rxtstamp for the regular and 8021q tagger are completely
independent. With tag_8021q, the timestamp must come from the packet's
duplicate delivered to the CPU port module, but there is potentially
complex logic to be handled [ and prone to reordering ] if we were to
just start reading packets from the CPU port module, and try to match
them to the one we received over Ethernet and which needs an RX
timestamp. So we do something simple: we tell DSA "give me some time to
think" (we request skb deferral by returning false from .port_rxtstamp)
and we just drop the frame we got over Ethernet with no attempt to match
it to anything - we just treat it as a notification that there's data to
be processed from the CPU port module's queues. Then we proceed to read
the packets from those, one by one, which we deliver up the stack,
timestamped, using netif_rx - the same function that any driver would
use anyway if it needed RX timestamp deferral. So the assumption is that
we'll come across the PTP packet that triggered the CPU extraction
notification eventually, but we don't know when exactly. Thanks to the
VCAP IS2 trap/redirect rule and the exclusion of the CPU port module
from the flooding replicators, only PTP frames should be present in the
CPU port module's RX queues anyway.
There is just one conflict between the VCAP IS2 trapping rule and the
semantics of the BPF classifier. Namely, ptp_classify_raw() deems
general messages as non-timestampable, but still, those are trapped to
the CPU port module since they have an EtherType of ETH_P_1588. So, if
the "no XTR IRQ" workaround is in place, we need to run another BPF
classifier on the frames extracted over MMIO, to avoid duplicates being
sent to the stack (once over Ethernet, once over MMIO). It doesn't look
like it's possible to install VCAP IS2 rules based on keys extracted
from the 1588 frame headers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the tag_8021q tagger is software-defined, it has no means by
itself for retrieving hardware timestamps of PTP event messages.
Because we do want to support PTP on ocelot even with tag_8021q, we need
to use the CPU port module for that. The RX timestamp is present in the
Extraction Frame Header. And because we can't use NPI mode which redirects
the CPU queues to an "external CPU" (meaning the ARM CPU running Linux),
then we need to poll the CPU port module through the MMIO registers to
retrieve TX and RX timestamps.
Sadly, on NXP LS1028A, the Felix switch was integrated into the SoC
without wiring the extraction IRQ line to the ARM GIC. So, if we want to
be notified of any PTP packets received on the CPU port module, we have
a problem.
There is a possible workaround, which is to use the Ethernet CPU port as
a notification channel that packets are available on the CPU port module
as well. When a PTP packet is received by the DSA tagger (without timestamp,
of course), we go to the CPU extraction queues, poll for it there, then
we drop the original Ethernet packet and masquerade the packet retrieved
over MMIO (plus the timestamp) as the original when we inject it up the
stack.
Create a quirk in struct felix is selected by the Felix driver (but not
by Seville, since that doesn't support PTP at all). We want to do this
such that the workaround is minimally invasive for future switches that
don't require this workaround.
The only traffic for which we need timestamps is PTP traffic, so add a
redirection rule to the CPU port module for this. Currently we only have
the need for PTP over L2, so redirection rules for UDP ports 319 and 320
are TBD for now.
Note that for the workaround of matching of PTP-over-Ethernet-port with
PTP-over-MMIO queues to work properly, both channels need to be
absolutely lossless. There are two parts to achieving that:
- We keep flow control enabled on the tag_8021q CPU port
- We put the DSA master interface in promiscuous mode, so it will never
drop a PTP frame (for the profiles we are interested in, these are
sent to the multicast MAC addresses of 01-80-c2-00-00-0e and
01-1b-19-00-00-00).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the felix DSA driver will need to poll the CPU port module for
extracted frames as well, let's create some common functions that read
an Extraction Frame Header, and then an skb, from a CPU extraction
group.
We abuse the struct ocelot_ops :: port_to_netdev function a little bit,
in order to retrieve the DSA port net_device or the ocelot switchdev
net_device based on the source port information from the Extraction
Frame Header, but it's all in the benefit of code simplification -
netdev_alloc_skb needs it. Originally, the port_to_netdev method was
intended for parsing act->dev from tc flower offload code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot tagger is a hot mess currently, it relies on memory
initialized by the attached driver for basic frame transmission.
This is against all that DSA tagging protocols stand for, which is that
the transmission and reception of a DSA-tagged frame, the data path,
should be independent from the switch control path, because the tag
protocol is in principle hot-pluggable and reusable across switches
(even if in practice it wasn't until very recently). But if another
driver like dsa_loop wants to make use of tag_ocelot, it couldn't.
This was done to have common code between Felix and Ocelot, which have
one bit difference in the frame header format. Quoting from commit
67c2404922 ("net: dsa: felix: create a template for the DSA tags on
xmit"):
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
The really interesting part is that Seville should have had its own
tagging protocol defined - it is not compatible on the wire with Ocelot,
even for that single bit. In principle, a packet generated by
DSA_TAG_PROTO_OCELOT when booted on NXP LS1028A would look in a certain
way, but when booted on NXP T1040 it would look differently. The reverse
is also true: a packet generated by a Seville switch would be
interpreted incorrectly by Wireshark if it was told it was generated by
an Ocelot switch.
Actually things are a bit more nuanced. If we concentrate only on the
DSA tag, what I said above is true, but Ocelot/Seville also support an
optional DSA tag prefix, which can be short or long, and it is possible
to distinguish the two taggers based on an integer constant put in that
prefix. Nonetheless, creating a separate tagger is still justified,
since the tag prefix is optional, and without it, there is again no way
to distinguish.
Claiming backwards binary compatibility is a bit more tough, since I've
already changed the format of tag_ocelot once, in commit 5124197ce5
("net: dsa: tag_ocelot: use a short prefix on both ingress and egress").
Therefore I am not very concerned with treating this as a bugfix and
backporting it to stable kernels (which would be another mess due to the
fact that there would be lots of conflicts with the other DSA_TAG_PROTO*
definitions). It's just simpler to say that the string values of the
taggers have ABI value starting with kernel 5.12, which will be when the
changing of tag protocol via /sys/class/net/<dsa-master>/dsa/tagging
goes live.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is one place where we cannot avoid accessing driver data, and that
is 2-step PTP TX timestamping, since the switch wants us to provide a
timestamp request ID through the injection header, which naturally must
come from a sequence number kept by the driver (it is generated by the
.port_txtstamp method prior to the tagger's xmit).
However, since other drivers like dsa_loop do not claim PTP support
anyway, the DSA_SKB_CB(skb)->clone will always be NULL anyway, so if we
move all PTP-related dereferences of struct ocelot and struct ocelot_port
into a separate function, we can effectively ensure that this is dead
code when the ocelot tagger is attached to non-ocelot switches, and the
stateful portion of the tagger is more self-contained.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.
Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).
The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taggers should be written to do something valid irrespective of the
switch driver that they are attached to. This is even more true now,
because since the introduction of the .change_tag_protocol method, a
certain tagger is not necessarily strictly associated with a driver any
longer, and I would like to be able to test all taggers with dsa_loop in
the future.
In the case of ocelot, it needs to move the classified VLAN from the DSA
tag into the skb if the port is VLAN-aware. We can allow it to do that
by looking at the dp->vlan_filtering property, no need to invoke
structures which are specific to ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix DSA driver will inject some frames through register MMIO, same
as ocelot switchdev currently does. So we need to be able to reuse the
common code.
Also create some shim definitions, since the DSA tagger can be compiled
without support for the switch driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks a bit nicer than the open-coded "(x + 3) % 4" idiom.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_rx_frame_word() function can return a negative error code,
however this isn't being checked for consistently. Errors being ignored
have not been seen in practice though.
Also, some constructs can be simplified by using "goto" instead of
repeated "break" statements.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that the intention of this snippet of code is to not exit
ocelot_xtr_irq_handler() while in the middle of extracting a frame.
The problem in extracting it word by word is that future extraction
attempts are really easy to get desynchronized, since the IRQ handler
assumes that the first 16 bytes are the IFH, which give further
information about the frame, such as frame length.
But during normal operation, "err" will not be 0, but 4, set from here:
for (i = 0; i < OCELOT_TAG_LEN / 4; i++) {
err = ocelot_rx_frame_word(ocelot, grp, true, &ifh[i]);
if (err != 4)
break;
}
if (err != 4)
break;
In that case, draining the extraction queue is a no-op. So explicitly
make this code execute only on negative err.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the xtr (extraction) IRQ of the ocelot switch is not shared, then
if it fired, it means that some data must be present in the queues of
the CPU port module. So simplify the code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Error recovery optimizations.
This series implements some optimizations to error recovery. One
patch adds an echo/reply mechanism with firmware to enhance error
detection. The other patches speed up the recovery process by
polling config space earlier and to selectively initialize
context memory during re-initialization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only log the error recovery settings if it is enabled.
In some cases, firmware disables error recovery after it was
initially enabled. Without logging anything, the user will not be
aware of this change in setting.
Log it when error recovery is disabled. Also, change the reset count
value from hexadecimal to decimal.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new async message that the firmware can send to check if it
can communicate with the driver. This is an added error detection
scheme that firmware can use if it suspects errors in the PCIe
interface. When the driver receives this async message, it will reply
back echoing some data in the async message. If the firmware is not
getting the reply with the proper data after some retries, error
recovery will kick in.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware provides the offset to the "context kind" field of the
relevant context memory blocks, we'll initialize just that field for
each block instead of initializing all of context memory.
Populate the bnxt_mem_init structure with the proper offset returned
by firmware. If it is older firmware and the information is not
available, we set the offset to an invalid value and fall back to
the old behavior of initializing every byte. Otherwise, we initialize
only the "context kind" byte at the offset.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver calls memset() to set all relevant context memory
used by the chip to the initial value. This can take many milliseconds
with the potentially large number of context pages allocated for the
chip.
To make this faster, we only need to initialize the "context kind" field
of each block of context memory. This patch sets up the infrastructure
to do that with the bnxt_mem_init structure. In the next patch, we'll
add the logic to obtain the offset of the "context kind" from the
firmware. This patch is not changing the current behavior of calling
memset() to initialize all relevant context memory.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During some fatal firmware error conditions, the PCI config space
register 0x2e which normally contains the subsystem ID will become
0xffff. This register will revert back to the normal value after
the chip has completed core reset. If we detect this condition,
we can poll this config register immediately for the value to revert.
Because we use config read cycles to poll this register, there is no
possibility of Master Abort if we happen to read it during core reset.
This speeds up recovery significantly as we don't have to wait for the
conservative min_time before polling MMIO to see if the firmware has
come out of reset. As soon as this register changes value we can
proceed to re-initialize the device.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer devices may have local context memory instead of relying on the
host for backing store. In these cases, HWRM_FUNC_BACKING_STORE_QCAPS
will return a zero entry size to indicate contexts for which the host
should not allocate backing store.
Selectively allocate context memory based on device capabilities and
only enable backing store for the appropriate contexts.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main changes are the echo request/response from firmware for error
detection and the NO_FCS feature to transmit frames without FCS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
