Conversion from txt to yaml. The binding documents that
as not all boards will make use of the ADC channels via a consumer
driver. It does no harm however, so we will leave it as required.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: David Lechner <david@lechnology.com>
Cc: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20200830161154.3201-3-jic23@kernel.org
Simple binding conversion from txt to yaml.
Only addition was #io-channel-cells to allow for potential consumers
of the channels on this device.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Link: https://lore.kernel.org/r/20200830161154.3201-2-jic23@kernel.org
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock.
The lock protect the state of the device from potential concurrent writes.
The device is configured via a sequence of SPI writes, and this lock is
meant to prevent the start of another sequence before another one has
finished.
This is part of a bigger cleanup.
Link: https://lore.kernel.org/linux-iio/CA+U=Dsoo6YABe5ODLp+eFNPGFDjk5ZeQEceGkqjxXcVEhLWubw@mail.gmail.com/
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200916092731.77220-1-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state from potential concurrent write
accesses from userspace. The write operation requires an SPI write, then
toggling of a GPIO, so the lock aims to protect the sanity of the entire
sequence of operation.
This is part of a bigger cleanup.
Link: https://lore.kernel.org/linux-iio/CA+U=Dsoo6YABe5ODLp+eFNPGFDjk5ZeQEceGkqjxXcVEhLWubw@mail.gmail.com/
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200916092535.76527-1-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock. The lock protects against potential races when
reading the CR reg and then updating, so that the state of pm_runtime
is consistent between the two operations.
This is part of a bigger cleanup.
Link: https://lore.kernel.org/linux-iio/CA+U=Dsoo6YABe5ODLp+eFNPGFDjk5ZeQEceGkqjxXcVEhLWubw@mail.gmail.com/
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Link: https://lore.kernel.org/r/20200916092349.75647-1-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Extend support to read/write byte data from/to the device using
debugfs iio interface.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200910180450.29696-4-nish.malpani25@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Include 'interrupts' property and provide a suitable example for using
a GPIO interrupt line.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Link: https://lore.kernel.org/r/20200910180450.29696-3-nish.malpani25@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Provide a way for continuous data capture by setting up buffer support. The
data ready signal exposed at the SYNC pin of the ADXRS290 is exploited as
a hardware interrupt which triggers to fill the buffer.
Triggered buffer setup was tested with both hardware trigger (DATA_RDY) and
software triggers (sysfs-trig & hrtimer).
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200910180450.29696-2-nish.malpani25@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_add_action_or_reset() hook to switch device into STANDBY
mode during standard resource unwinding. The patch includes a helper
function, in the form of adxrs290_set_mode(), to realise driving the
device into STANDBY mode.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200910122711.16670-1-nish.malpani25@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Conversion of error paths to dev_err_probe() dropped one return
statement. The driver will continue to probe if getting booster
regulator fails.
Fixes: ce30eeb613 ("iio: adc: stm32: Simplify with dev_err_probe()")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1599727927-7776-1-git-send-email-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We found some sensors which are much slower (20% at room temperature)
than nominal. According to the data sheet, up to 27% is possible. Now I
add 33% to the nominal time out, hopefully this is enough.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Link: https://lore.kernel.org/r/20200909154439.10308-1-ceggers@arri.de
Fixes: 403e5586b5 ("iio: light: as73211: New driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since object temperature might be different than the sensor temperature
the infrared sensors should provide an interface to inject ambient
temperature. This was in past done via write to ambient temperature
interface (in_temp_ambient_raw), but I think most people did not know
about it. This solution introduces a new iio type of the CALIBAMBIENT
which is hopefully more descriptive and more explicit about the purpose
and capabilities of the sensors.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200906210231.383976-1-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Hartmut Knaack was an active reviewer and contributor to the IIO
subsystem and drivers. However his last message on LKML is from
October 2015.
In thanks for Hartmut's effort, move him name to the Credits.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio <linux-iio@vger.kernel.org>
Link: https://lore.kernel.org/r/20200903181926.5606-2-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Emails to Beniamin Bia bounce with no such address so remove him from
maintainers. After this removal, many entries for Analog Devices Inc
IIO drivers look exactly the same so consolidate them.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio <linux-iio@vger.kernel.org>
Link: https://lore.kernel.org/r/20200903181926.5606-1-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On one board I found that:
probe of 5-0028 returned 1 after 259547 usecs
While some of this time is attributable to the pile of i2c transfers
that we do at probe time, the lion's share (over 200 ms) is sitting
waiting in the polling loop in sx9310_init_compensation() waiting for
the hardware to indicate that it's done.
There's no reason to block probe of all other devices on our probe.
Turn on async probe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Daniel Campello <campello@chromium.org>
Link: https://lore.kernel.org/r/20200901081920.v2.1.Id02b2f451b3eed71ddd580f4b8b44b3e33e84970@changeid
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There seems no reason to allow for compile-testing on ARM only, so
remove this restriction.
Build-tested with allyesconfig on x86.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200904170416.16061-1-alex.dewar90@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are few blank lines that split structure definitions
with their users. Remove them to increase readability.
While here, update copyright year.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200831090813.78841-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver is quite likely used only on ACPI based platforms and
rarely build with CONFIG_ACPI=n. Even though, the few dozens of bytes
is better than ugly ifdeffery and inclusion of heavy header.
As a result, replace acpi.h with mod_devicetable.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200831090813.78841-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert to use ->read_avail() instead of open-coded attribute handling.
While here, fix the typo in array definition and append comma in case of
the future extension.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200831090813.78841-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Potentially bma220_init() and bma220_deinit() may return positive codes.
Fix the logic to return proper error codes instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200831090813.78841-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drops the deprecated compatibles without the vendor name.
Whilst the driver continues to support these for old dt blobs,
any dt bindings that are actuallly verified against this document should
be fixed to add the vendor name.
Added the #io-channel-cells property to allow for consumers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Oskar Andero <oskar.andero@gmail.com>
Link: https://lore.kernel.org/r/20200809111753.156236-2-jic23@kernel.org
A transfer may fall shorter than the bytes in the block.
This information is available in the residue from the DMA engine, so we can
compute actual `bytes_used` with that by subtracting the residue.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20200826052011.13348-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simple binding so easy to convert.
Dropped the stated value of maximum spi bus frequency as it does
not seem to correspond to the datasheet. The value of 200kHz
is the max sampling frequency of the ADC, not the clock frequency of
the SPI bus.
Added #io-channel-cells to allow use as a provider of channels to
other devices via the consumer binding.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-By: Phil Reid <preid@electromag.com.au>
Cc: Phil Reid <preid@electromag.com.au>
Link: https://lore.kernel.org/r/20200809111753.156236-14-jic23@kernel.org
JC: Seems that I messed up applying the original driver patches, and
this file never actually made it into the tree.
I have picked up original Ack and Sign-off so as to record the
history.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200809111753.156236-13-jic23@kernel.org
Simple binding. Only addition to txt version is
as a provider of channels to other devices using the consumer
binding.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Link: https://lore.kernel.org/r/20200809111753.156236-10-jic23@kernel.org
Simple binding conversion of this SPI ADC binding, with reference
voltage.
Added the optional property #io-channel-cells to allow for
consumers of channels if that makes sense for a given board.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Link: https://lore.kernel.org/r/20200809111753.156236-7-jic23@kernel.org
Simple conversion for this ADC driver. Note that I haven't put
limits on the spi-max-sampling-frequency because the adc161s626
doesn't state one clearly defined value.
Added the #io-channel-cells property to allow for consumers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Link: https://lore.kernel.org/r/20200809111753.156236-6-jic23@kernel.org
Very simple binding for this i2c device with a reference supply.
Added the #io-channel-cells property to allow for consumers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20200809111753.156236-5-jic23@kernel.org
Very simple conversion of spi device with reference supply.
Added the #io-channel-cells property to allow for consumers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/20200809111753.156236-4-jic23@kernel.org
These i2c devices have simple bindings, well described by trivial-device.yaml
so rather than convert the binding doc to yaml, let us just add them to
trivial devices and drop the old binding document.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Link: https://lore.kernel.org/r/20200809111753.156236-3-jic23@kernel.org
By default, if all three channels (x, y, z) are enabled, sample sets of
concurrent 3-axis data is stored in the FIFO. This patch adds the option
to configure the FIFO to store peak acceleration (x, y and z) of every
over-threshold event. When pushing to iio buffer we push only enabled
axis data.
Currently the driver configures adxl372 to work in loop mode.
The inactivity and activity timings decide how fast the chip
will loop through the awake and waiting states and the
thresholds on x,y,z axis decide when activity or inactivity
will be detected.
This patch adds standard events sysfs entries for the inactivity
and activity timings: thresh_falling_period/thresh_rising_period
and for the in_accel_x_thresh_falling/rising_value.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200810093257.65929-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is some inconsistency and whitespace cleanup performed in this
patch. It was done on top of my other patches, but I can rebase to head
of the togreg branch if it would go in sooner.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200818213737.140613-6-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For some time the market wants medical grade accuracy in medical range,
while still retaining the declared accuracy outside of the medical range
within the same sensor. That is why we created extended calibration
which is automatically switched to when object temperature is too high.
This patch also introduces the object_ambient_temperature variable which
is needed for more accurate calculation of the object infra-red
footprint as sensor's ambient temperature might be totally different
than what the ambient temperature is at object and that is why we can
have some more errors which can be eliminated. Currently this temperature
is fixed at 25, but the interface to adjust it by user (with external
sensor or just IR measurement of the other object which acts as ambient),
will be introduced in another commit.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200818213737.140613-5-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduce number of lines and improve readability to convert polling while
loops to regmap_read_poll_timeout.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200818213737.140613-4-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Document internal/private struct for mlx90632 device.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200818213737.140613-3-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
TAdut4 was calculated each iteration although it did not change. In light
of near future additions of the Extended range DSP calculations, this
function refactoring will help reduce unrelated changes in that series as
well as reduce the number of new functions needed.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200818213737.140613-2-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Insert a missing mutex_init() call during the probe that initializes
the driver's local lock to unlocked state.
Fixes: 2c8920fff1 ("iio: gyro: Add driver support for ADXRS290")
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Link: https://lore.kernel.org/r/20200825124552.11155-1-nish.malpani25@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20200829064726.26268-18-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200829064726.26268-17-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200829064726.26268-16-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200829064726.26268-15-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200829064726.26268-14-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
