Some bits from the flags2 field are going to be used in the next
patches, so replace the whole-byte definition with the actual bits and
document their versions.
This patch is based on a patch by Animesh Manna.
Cc: Animesh Manna <animesh.manna@intel.com>
Credits-to: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614221018.19044-2-paulo.r.zanoni@intel.com
ICL DVFS is almost the same as CNL, except for the CDCLK/DDICLK
table. Implement it just like CNL does.
References: commit 48469eced2 ("drm/i915: Use cdclk_state->voltage
on CNL")
References: commit 53e9bf5e81 ("drm/i915: Adjust system agent
voltage on CNL if required by DDI ports")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614221018.19044-1-paulo.r.zanoni@intel.com
We can avoid the mmio read of the CSB pointers after reset based on the
knowledge that the HW always start writing at entry 0 in the CSB buffer.
We need to reset our CSB head tracking after GPU reset (and on
sanitization after resume) so that we are expecting to read from entry
0, hence we reset our head tracking back to the entry before (the last
entry in the ring).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615093137.14270-2-chris@chris-wilson.co.uk
As we want to be able to call i915_reset_engine and co from a softirq or
timer context, we need to be irqsafe at all times. So we have to forgo
the simple spin_lock_irq for the full spin_lock_irqsave.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615093137.14270-1-chris@chris-wilson.co.uk
If client is smart or lucky enough to create a new context
after each hang, our context banning mechanism will never
catch up, and as a result of that it will be saved from
client banning. This can result in a never ending streak of
gpu hangs caused by bad or malicious client, preventing
access from other legit gpu clients.
Fix this by always incrementing per client ban score if
it hangs in short successions regardless of context ban
scoring. The exception are non bannable contexts. They remain
detached from client ban scoring mechanism.
v2: xchg timestamp, tidyup (Chris)
v3: comment, bannable & banned together (Chris)
Fixes: b083a0870c ("drm/i915: Add per client max context ban limit")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615104429.31477-1-mika.kuoppala@linux.intel.com
For each platform, we have a few registers that are rewritten with
different values -- they are not part of a sequence, just different parts
of a masked register set at different times (e.g. platform and gen
workarounds). Consolidate these into a single register write to keep the
table compact, important since we are running of room in the current
fixed sized buffer.
While adjusting the construction of the wa table, make it non fatal so
that the driver still loads but keeping the warning and extra details
for inspection.
Inspecting the changes for a Kabylake system,
Before:
Address val mask read
0x07014 0x20002000 0x00002000 0x00002100
0x0E194 0x01000100 0x00000100 0x00000114
0x0E4F0 0x81008100 0x00008100 0xFFFF8120
0x0E184 0x00200020 0x00000020 0x00000022
0x0E194 0x00140014 0x00000014 0x00000114
0x07004 0x00420042 0x00000042 0x000029C2
0x0E188 0x00080000 0x00000008 0x00008030
0x07300 0x80208020 0x00008020 0x00008830
0x07300 0x00100010 0x00000010 0x00008830
0x0E184 0x00020002 0x00000002 0x00000022
0x0E180 0x20002000 0x00002000 0x00002000
0x02580 0x00010000 0x00000001 0x00000004
0x02580 0x00060004 0x00000006 0x00000004
0x07014 0x01000100 0x00000100 0x00002100
0x0E100 0x00100010 0x00000010 0x00008050
After:
Address val mask read
0x02580 0x00070004 0x00000007 0x00000004
0x07004 0x00420042 0x00000042 0x000029C2
0x07014 0x21002100 0x00002100 0x00002100
0x07300 0x80308030 0x00008030 0x00008830
0x0E100 0x00100010 0x00000010 0x00008050
0x0E180 0x20002000 0x00002000 0x00002000
0x0E184 0x00220022 0x00000022 0x00000022
0x0E188 0x00080000 0x00000008 0x00008030
0x0E194 0x01140114 0x00000114 0x00000114
0x0E4F0 0x81008100 0x00008100 0xFFFF8120
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615120207.13952-1-chris@chris-wilson.co.uk
DP spec 1.4 supports training pattern set 4 (TPS4) for HBR3 link
rate. This will be used in link training's channel equalization
phase if supported by both source and sink.
This patch adds the helpers to check if HBR3 is supported and uses
TPS4 in training pattern selection during link training.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611222655.5696-2-paulo.r.zanoni@intel.com
On ICP, port present straps (from SFUSE_STRAP PCH register) are no
longer supported. Software should determine the presence through BIOS
VBT, hotplug or other mechanisms.
v2: Improve commit message (Lucas).
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-14-paulo.r.zanoni@intel.com
Implement the hardware state readout code.
Thanks to Animesh Manna for spotting this problem.
Cc: Animesh Manna <animesh.manna@intel.com>
Credits-to: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-11-paulo.r.zanoni@intel.com
We can stop asserting using WARN_ON as given sufficient CI coverage, we
can rely on using GEM_BUG_ON() to catch problems before merging.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614184218.1606-2-chris@chris-wilson.co.uk
As the most frequent PTE encoding is for the scratch page, cache it upon
creation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614184218.1606-1-chris@chris-wilson.co.uk
As we cannot reliably change used page tables while the context is
active, the earliest opportunity we have to recover excess pages is when
the context becomes idle. So whenever we unbind the context (it must be
idle, and indeed being evicted) free the unused ptes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614134315.5900-2-chris@chris-wilson.co.uk
As we were only supporting aliasing_ppgtt on gen7 for some time, we
saved a few checks by preallocating the page directories on creation.
However, since we need 2MiB of page directories for each ppgtt, to
support arbitrary numbers of user contexts, we need to be more prudent
in our allocations, and defer the page allocation until it is used. We
don't recover unused pages yet as we found that doing so on the fly
(i.e. altering TLB entries) would confuse the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614134315.5900-1-chris@chris-wilson.co.uk
Hangcheck is our back up in case the GPU or the driver gets stuck. It
detects when the GPU is not making any progress and issues a GPU reset.
However, if the driver is failing to make any progress, we can get
ourselves into a situation where we continually try resetting the GPU to
no avail. Employ a second timeout such that if we continue to see the
same seqno (the stalled engine has made no progress at all) over the
course of several hangchecks, declare the driver wedged and attempt to
start afresh.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180602104853.17140-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
In the unlikely case where we have failed to keep submitting to the GPU,
we end up with the ELSP queue empty but a pending queue of requests.
Here, we skip the per-engine reset as there is no guilty request, but in
doing so we also skip the engine restart leaving ourselves with a
permanently hung engine. A quick way to recover is by moving the tasklet
kick to execlists_reset_finish() (from init_hw). We still emit the error
on hanging, so the error is not lost but we should be able to recover.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604073441.6737-2-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
With an old (4.7.3 on 32bit) gcc, it emits a warning for
In file included from drivers/gpu/drm/i915/i915_request.c:1425:0:
drivers/gpu/drm/i915/selftests/i915_request.c: In function ‘live_nop_request’:
drivers/gpu/drm/i915/selftests/i915_request.c:380:21: error: ‘request’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
Silence it by just setting it to NULL on initialisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614124923.18071-1-chris@chris-wilson.co.uk
While Bspec doesn't list a specific sequence for turning off the DP port
on g4x we are getting an underrun if the port is disabled in the
.disable() hook. Looks like the pipe stops when the port stops, and by
that time the plane disable may not have completed yet. Also the plane(s)
seem to end up in some wonky state when this happens as they also signal
another underrun immediately after we turn them back on during the next
enable sequence.
We could add a vblank wait in .disable() to avoid wedging the planes,
but I assume we're still tripping up the pipe in some way. So it seems
better to me to just follow the ILK+ sequence and turn off the DP port
in .post_disable() instead. This sequence doesn't seem to suffer from
this problem. Could be it was always the intended sequence for DP and
the gen4 bspec was just never updated to include it.
Originally we used the bad sequence even on ilk+, but I changed that
in commit 08aff3fe26 ("drm/i915: Move DP port disable to post_disable
for pch platforms") as it was causing issues on those platforms as well.
I left out g4x then only because I didn't have the hardware to test it.
Now that I do it's fairly clear that the ilk+ sequence is also the
right choice for g4x.
v2: Fix whitespace fail (Jani)
Mention the ilk+ commit (Jani)
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
On i965/g4x IIR is edge triggered. So in order for IIR to notice that
there is still a pending interrupt we have to force and edge in ISR.
For the ISR/IIR pipe event bits we can do that by temporarily
clearing all the PIPESTAT enable bits when we ack the status bits.
This will force the ISR pipe event bit low, and it can then go back
high when we restore the PIPESTAT enable bits.
This avoids the following race:
1. stat = read(PIPESTAT)
2. an enabled PIPESTAT status bit goes high
3. write(PIPESTAT, enable|stat);
4. write(IIR, PIPE_EVENT)
The end result is IIR==0 and ISR!=0. This can lead to nasty
vblank wait/flip_done timeouts if another interrupt source
doesn't trick us into looking at the PIPESTAT status bits despite
the IIR PIPE_EVENT bit being low.
Before i965 IIR was level triggered so this problem can't actually
happen there. And curiously VLV/CHV went back to the level triggered
scheme as well. But for simplicity we'll use the same i965/g4x
compatible code for all platforms.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106033
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105225
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106030
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
On ICL for setting the HDMI infoframe the pipe clock needs to be
enabled, otherwise accessing the VIDEO_DIP_CTL register will hang the
machine.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-5-imre.deak@intel.com
The only requirement by BSpec for setting the HDMI infoframes is on DDI
platforms to do that before enabling the HDMI transcoder function, see
VIDEO_DIP_CTL bit 16. Accordingly check for the transcoder function
disabled state instead of the port's disabled state on DDI platforms.
This is needed by the next patch as it will set the infoframe during
crtc disabling where the port is still enabled.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-4-imre.deak@intel.com
On ICL the pipe clock needs to be enabled before setting the HDMI
infoframe, but these steps are in the reverse order atm. Move the pipe
clock enabling to the encoders, so reordering of the two steps can be
done in a clean way.
No functional change.
v2:
- Rebased on drm-tip.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613172746.18525-1-imre.deak@intel.com
crtc->config points to the old crtc state at the point
display.crtc_disable() is called, so use the more descriptive pointer
instead.
v2:
- Convert one remaining instance of the ptr in the function. (Ville)
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-2-imre.deak@intel.com
The immediate enabling was actually not an issue for the
HW perspective for core platforms that have HW tracking.
HW will wait few identical idle frames before transitioning
to actual psr active anyways.
Now that we removed VLV/CHV out of the picture completely
we can safely remove any delays.
Note that this patch also remove the delayed activation
on HSW and BDW introduced by commit 'd0ac896a477d
("drm/i915: Delay first PSR activation.")'. This was
introduced to fix a blank screen on VLV/CHV and also
masked some frozen screens on other core platforms.
Probably the same that we are now properly hunting and fixing.
v2:(DK): Remove unnecessary WARN_ONs and make some other
VLV | CHV more readable.
v3: Do it regardless the timer rework.
v4: (DK/CI): Add VLV || CHV check on cancel work at psr_disable.
v5: Kill remaining items and fully rework activation functions.
v6: Rebase on top of VLV/CHV clean-up and keep the reactivation
on a regular non-delayed work to avoid extra delays on exit
calls and allow us to add few more safety checks before
real activation.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613192600.3955-1-rodrigo.vivi@intel.com
In order to be able to evict the gen6 ppgtt, we have to unpin it at some
point. We can simply use our context activity tracking to know when the
ppgtt is no longer in use by hardware, and so only keep it pinned while
being used a request.
For the kernel_context (and thus aliasing_ppgtt), it remains pinned at
all times, as the kernel_context itself is pinned at all times.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-5-chris@chris-wilson.co.uk
Currently we use %08x for the row offset, and %08x for the binary
contents of the buffer. This makes it very easily to confuse the two, so
switch to using [%04x] for the start-of-row offset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-3-chris@chris-wilson.co.uk
Sometimes we need to see what instructions we emitted for a request to
try and gather a glimmer of insight into what the GPU is doing when it
stops responding.
v2: Move ring dumping into its own routine
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614122150.17552-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Pass a local acpi_handle around instead of having a static dsm priv
structure. If we need it later, we can always move it to dev_priv, and
the change at hand will make that easier as well.
Care is taken to preserve old behaviour, particularly using the last
non-NULL acpi handle, whether it makes sense or not.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614104709.2808-1-jani.nikula@intel.com
This should be a no-op in terms of our control flow, we move the
sanitization (GPU reset) from the bottom of the early resume phase to
the top of the next. However, following hibernation debug, the power
code skips the early resume phase, but as we are about to completely
restore the GTT mappings, we first need to stop the GPU using them i.e.
perform a GPU reset (i915_gem_sanitize()).
Testcase: igt/gem_exec_suspend/basic-S4-devices
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
For symmetry, simplicity and ensuring the request is always truly idle
upon its completion, always emit the closing flush prior to emitting the
request breadcrumb. Previously, we would only emit the flush if we had
started a user batch, but this just leaves all the other paths open to
speculation (do they affect the GPU caches or not?) With mm switching, a
key requirement is that the GPU is flushed and invalidated before hand,
so for absolute safety, we want that closing flush be mandatory.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612105135.4459-1-chris@chris-wilson.co.uk
When encountering a connector with the scaling mode property both
intel and modesetting ddxs sometimes add tons of DBLSCAN modes
to the output's mode list. The idea presumably being that since the
output will be going through the panel fitter anyway we can pretend
to use any kind of mode.
Sadly that means we can't reject user modes with the DBLSCAN flag
until we know whether we're going to be using the panel's native
mode or the user mode directly. Doing otherwise means X clients using
xf86vidmode/xrandr will get a protocol error (and often self
terminate as a result) when the kernel refuses to use the requested
mode with the DBLSCAN flag.
To undo the regression we'll move the DBLSCAN checks into the
connector->mode_valid() and encoder->compute_config() hooks.
Cc: stable@vger.kernel.org
Cc: Vito Caputo <vcaputo@pengaru.com>
Reported-by: Vito Caputo <vcaputo@pengaru.com>
Fixes: e995ca0b81 ("drm/i915: Provide a device level .mode_valid() hook")
References: https://lkml.org/lkml/2018/5/21/715
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180524125403.23445-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106804
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Enable KVMGT for BXT.
is_supported_device() acting as the gatekeeper of GVT-g init.
If all supported platforms share the same configurations for some
specific feature, platform check will rely on this check only.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Leverage most SKL/KBL mmio init info and add different mmio to
BXT specific function init_bxt_mmio_info().
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Virtual monitor on BXT start from port B.
Unlike SKL/KBL, digital display port connectivity is detected via
GEN8_DE_PORT_ISR so emulate monitor state change by setting it.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
BXT forcewake is handled in the same way as SKL/KBL.
v2: Add missing inhibit_context restore for BXT.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Handle BXT cmd_parser as SKL/KBL.
v2: All supported platforms share the same routines.
Remove the platform check by now and let is_supported_device()
be the gate keeper.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Handle pending tlb flush, mocs/mmio switch and context as KBL.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Initialize BXT irq handler as SKL/KBL.
v2: All supported platforms share the same irq ops and map.
Remove the platform check by now and let is_supported_device()
be the gate keeper.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Initialize BXT gtt as SKL/KBL.
v2: All supported platforms share the same gtt ops.
Remove the platform check by now and let is_supported_device()
be the gate keeper.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Initialize BXT device info as SKL/KBL.
v2: All supported platforms share the same device configuration.
Remove the platform check by now and let is_supported_device()
be the gate keeper.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Broxton belongs to GEN9 family so add to SKL and GEN9 plus.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
