Store the upper dword of the register offset in the whitelist as well.
This would allow it to read register where the two halves aren't sitting
right next to each other, and it'll make it easier to make register
access type safe.
While at it change the register offsets to u32 from u64. Our register
space isn't quite that big, yet :)
v2: Use ldw/udw as the suffixes, and add a note about
64bit wide split regs (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446839021-18599-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Most of our register defines follow the convention that if there's a
need for the raw register offset, that one has an underscore sa a
prefix. The define (possibly parametrized) without the underscore is
the one people should normally use, since it will take into account
all the parameters and other potential offsets that are needed.
Fix up the few stragglers that don't follow this convention.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-14-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Handle DC off as a power well where enabling the power well will prevent
the DMC to enter selected DC states (required around modesets and Aux
A). Disabling the power well will allow DC states again. For now the
highest DC state is DC6 for Skylake and DC5 for Broxton but will be
configurable for Skylake in a later patch.
v2: Check both DC5 and DC6 bits in power well enabled function (Ville)
v3:
- Remove unneeded DC_OFF case in skl_set_power_well() (Imre)
- Add PW2 dependency to DC_OFF (Imre)
v4: Put DC_OFF before PW2 in BXT power well array
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[fixed line over 80 and parenthesis alignment checkpatch warns (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1447687201-24759-1-git-send-email-patrik.jakobsson@linux.intel.com
lookup_power_well() expects uniq power well IDs, but atm we have
uninitialized IDs which would clash with those power wells with a 0
ID. This wasn't a problem so far since nothing looked up such a power
well, but an upcoming patch will (Misc IO for SKL), so fix this up on
platforms where this matters.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-2-git-send-email-imre.deak@intel.com
Drop the EDP_PSR_BASE() thing, and just stick the PSR register offset
under dev_priv, like we for DSI and GPIO for example.
TODO: could probably move a bunch of this kind of stuff into the device
info instead...
v2: Drop the spurious whitespace change (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-7-git-send-email-ville.syrjala@linux.intel.com
Currently we determine the location of the AUX registers in a confusing
way. First we assume the PCH registers are used always, but then we
override it for everything but HSW/BDW to use DP+0x10. Very confusing.
Let's just make it straightforward and simply add a few functions to
pick the right AUX_CTL based on the DP port.
To deal with VLV/CHV we'll include the display_mmio_offset into the
AUX register defines.
v2: Reorder patches (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-5-git-send-email-ville.syrjala@linux.intel.com
v2: Keep some MISSING_CASE() stuff (Jani)
s/-1/-PIPE_B/ in the register macro
Fix typo in patch subject
v3: Use PORT_B registers for invalid ports in g4x_aux_ctl_reg() (Jani)
v4: Reorder patches (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v3)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-4-git-send-email-ville.syrjala@linux.intel.com
We check these to determine firmware loading status. Include
them to help to debug causes of firmware loading fails.
v2: Move all CSR specific registers to i915_reg.h (Ville)
v3: Rebase
v4: Rebase (RPM ref)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220487-32691-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
For bxt CSR firmware exposes a count of dc5 entries. Expose
it through debugs
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The CSR firmware expose two counters, handy to check if we are indeed
entering DC5/DC6.
v2: Rebase
v3: Take RPM ref before reading (Imre)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220412-32574-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
SWF18 is set if the display has been initialized by the pre-os. It also
gives what configuration is enabled on which pipe. In skl_sanitize_cdclk,
the DPLL sanity check can pass even if GOP/VBIOS is not loaded as BIOS
enables DPLL for integrated audio codec related programming.
So fisrt check if SWF18 is set and then follow through with other DPLL
and CDCLK verification. If not set then for sure we need to sanitize the
cdclock.
v2: Update the commit message for clarity (Siva)
v3: Correct the mask to check for bits[23:0] instead of only bits[16:0].
Had missed checking for PIPE C altogether. Remaining are reserved (Siva)
v4: Use ILK_SWF macro for SWF register definitions. Taken from Ville's patch
http://lists.freedesktop.org/archives/intel-gfx/2015-November/079480.html
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446726932-14078-1-git-send-email-shobhit.kumar@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Parametrize the SWF registers. This also fixes the register offsets,
which were mostly garbage in the old defines.
Also save/restore only as many SWF registers that each platform has.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PIPE_FRMCOUNT_GM45 and PIPE_FLIPCOUNT_GM45 names have bothered me
for a long time. The work equally well for ELK and onwards, so let's
s/GM45/G4X/.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few register mask defines were missing the '0x' from hex numbers. Or
at least I assume those were meant to be hex numbers. Put the '0x' in
place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always put parens around macro argument evaluations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Keep using the same registers (PCH_*) instead of accidentally
starting to use the other ones (BXT_*)2) (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note that in Bspec you have to dig around in a section called
"Timestamp bases" and Bspec update request is filed.
Signed-off-by: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Add note about state of Bspec.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to support glDispatchComputeIndirect for gen7.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BXT DSI clocks are different than previous platforms. So adding a
new function to program following clocks and dividers:
1. Program variable divider to generate input to Tx clock divider
(Output value must be < 39.5Mhz)
2. Select divide by 2 option to get < 20Mhz for Tx clock
3. Program 8by3 divider to generate Rx clock
v2: Fixed Jani's review comments. Adjusted the Macro definition as
per convention. Simplified the logic for bit definitions for
MIPI PORT A and PORT C in same registers.
v3: Refactored the macros for TX, RX Escape and DPHY clocks as per
Jani's suggestion.
v4: Addressed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains following changes:
1. MIPI device ready changes to support dsi_pre_enable. Changes
are specific to BXT device ready sequence. Added check for
ULPS mode(No effects on VLV).
2. Changes in dsi_enable to pick BXT port control register.
3. Changes in dsi_pre_enable to restrict DPIO programming for VLV
v2: Fixed Jani's review comments. Removed the changes in VLV/CHV
code. Fixed the macros to get proper port offsets.
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register was added on GEN4, by the name INSTDONE_1 whereas the GEN6
specification calls it INSTDONE_2. Keep the original name with a
platform prefix to make it clearer which INSTDONE register instance this
is. Also add a comment about the SNB alternative name.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a bunch of INSTDONE registers for different platforms and
purposes and it's not immediately clear which instance they are just by
looking at the register name. This one was added on GEN2, where it was
the only INSTDONE register, so mark it as such.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use 3 different names to refer to the same render ring INSTDONE
register. This can be confusing when comparing two parts of the code
accessing the register via different names. Although the GEN4 version's
layout is different, we treat it the same way as the GEN7+ version, in
that we simply read it out during error capture. So remove the
duplicates and leave a comment about the GEN4 difference.
Note that there is also a GEN2 version of this register, but that's on a
different address so not handled in this patch.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use SKL_DPLLx symbolic names instead of raw numbers
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added checks for available slices, subslices and EUs for Broadwell. This
information is filled in intel_device_info and is available to user with
GET_PARAM.
Added checks for enabled slices, subslices and EU for Broadwell. This
information is based on available counts but takes power gated slices
into account. It can be read in debugfs.
Introduce new register defines that contain information on slices on
Broadwell.
v2:
- Introduce GT_SLICE_INFO register
- Change Broadwell sseu_device_status function to use GT_SLICE_INFO
register instead of RPCS register
- Undo removal of dev_priv variables in Cherryview and Gen9
sseu_device_satus functions
v3:
- Fix style issues
v4:
- Corrected comment
- Reverted reordering of defines
Cc: Jeff Mcgee <jeff.mcgee@intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Łukasz Daniluk <lukasz.daniluk@intel.com>
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As with the cdclk, read out czclk from CCK as well. This gives us the
real current value and avoids having to decode fuses and whatnot.
Also store it in kHz under dev_priv like we do for cdlck since it's not
just an rps related clock, and having it in kHz is more
standard/convenient for some things.
Imre also pointed out that we currently fail to read czclk on VLV, which
means the PFI credit programming isn't working as expected.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the DISPLAY_TRUNK_* and DISPLAY_FREQUENCY_* bits to CCK_... instead
of DISPLAY_... to make it clear they apply to all CCK clock control registers.
Suggested by Ville.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Hide the 945 vs. rest of gen2/3 difference in the macro
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec update tells that we have to enable oscaledcompmethod instead of
ouniqetrangenmethod for enabling scale value during swing programming.
v2: Adding back 'don't care' values to bxt_ddi_translations_dp and add
error message if ouniquetrangemethod was set (Imre)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>(v1)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIXME: Should there be a WARN(i != 9) or something, or what does the
entry 9 comment mean?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Finally managed to dig up enough hints as to where the stolen
reserved stuff lives on ctg/elk. So add the code to decode it.
This was a combination of old chipset specs, diggin up an old
elk grits release with an ctg/elk AubLoad etc.
This was only tested on an elk as I don't have a ctg here
unfortunately.
This leaves ilk as the only platform that doesn't have a way
to detect this stuff. Looking at the register contents on my
ilk, it might be that the elk way works there too, but I
can't be sure since I can't affect the amount of reserved
memory on that machine, and if I am to trust the register
contents, by default it would reserve 0 bytes.
v2: s/WARN_ON_ONCE/WARN_ON/ since it's in one time init code
anyway (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch modifies dsi_prepare() function to support the same
modeset prepare sequence for BXT also. Main changes are:
1. BXT port control register is different than VLV.
2. BXT modeset sequence needs vdisplay and hdisplay programmed
for transcoder.
3. BXT can select PIPE for MIPI transcoders.
4. BXT needs to program register MIPI_INIT_COUNT for both the ports,
even if only one is being used.
v2: Fixed Jani's review comments. Rectified the DSI Macros to get
proper register offsets using _MIPI_PORT instead of _TRANSCODER
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds new functions for BXT clock and PLL programming.
They are:
1. configure_dsi_pll for BXT.
This function does the basic math and generates the divider ratio
based on requested pixclock, and program clock registers.
2. enable_dsi_pll function.
This function programs the calculated clock values on the PLL.
3. intel_enable_dsi_pll
Wrapper function to use same code for multiple platforms. It checks the
platform and calls appropriate core pll enable function.
v2: Fixed Jani's review comments. Macros are adjusted as per convention.
v3: Removed a redundant change wrt code comment.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normally we determine the backlight PWM modulation frequency (which we
also use as backlight max value) from the backlight registers at module
load time, expecting the registers have been initialized by the BIOS. If
this is not the case, we fail.
The VBT contains the backlight modulation frequency in Hz. Add platform
specific functions to convert the frequency in Hz to backlight PWM
modulation frequency, and use them to initialize the backlight when the
registers are not initialized by the BIOS.
v2: Fix SPT and VLV. Thanks to Clint for the VLV code.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite the BXT hpd setup to match the way we do it on other platforms:
- Throw out BXT_HOTPLUG_CTL since it's the same as PCH_PORT_HOTPLUG
- Enable the HPD bits in the DE port IER in gen8_de_irq_postinstall()
- Update DE port IMR using bdw_update_port_irq()
Also throw out port D from bxt_port_hotplug_long_detect() since BXT only
goes up to C.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL the port A HPD has moved to the PCH. Hook it up.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PORTA HPD defines are not BXT specific. They also exist on SPT,
and partially already on LPT:LP.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Indent the PORTx_HOTPLUG_... defines appropriately, and fix some space
vs. tab issues.
v2: Document pre-HSW/LPT bits, and order another tab (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
At various points when changing the DPIO lane/phy power states,
construct an expected value of the DISPLAY_PHY_STATUS register
and compare it with the real thing.
To construct the expected value we look at our shadow PHY_CONTROL
register value (which should match what we've just written to the
hardware), and we also need to look at the actual state of the cmn
power wells as a disabled power well causes the relevant LDO status
to be reported as 'on' in DISPLAY_PHY_STATUS.
When initially powering up the PHY it performs various internal
calibrations for which it fully powers up. That means that if we check
for the expetected power state immediately upon releasing cmnreset we
would get the occasional false positive. But we can of course
poll until the expected value appears. It shouldn't be too long so
this shouldn't make modesets substantially longer.
One extra complication is introduced when we cross the streams, ie.
drive port B with pipe B. In this case we trick CL2 (where the DPLL lives)
into life by temporaily powering up the lanes in the second channel,
and once the pipe is up and runnign we release the lane power override.
At that point the power state of CL2 has somehow gotten entangled with
the power state of the first channel. That means that constructing the
expected DISPLAY_PHY_STATUS value is a bit tricky since based on the
lane power states in the second channel, CL2 should also be powered
down. But we can use the DPLL enable bit to determine when CL2 should
be alive even if the lanes are powered down. However the power state
of CL2 isn't actually tied in with the DPLL state, but to the state
of the lanes in first channel, so we have to avoid checking the
expected state between shutting down the DPLL and powering down
the lanes in the first channel. So no calling assert_chv_phy_status()
before the DISPLAY_PHY_CONTROL write in chv_phy_powergate_lanes(),
but after the write is a safe time to check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add some checks that the state of the DPIO lanes is more or less what we
expect based on the overrides.
The hardware only provides two bits per channel indicating whether all
or some of the lanes are powered down, so we can't do an exact check.
Additionally, CL2 powering down before we can check it adds another
twist. To work around this we simply check for the 0 value of the
CL2 register (which is what we get when it's powered down) and
adjust our expectations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can choose to leave the display PHY CL2 powerdown up to some hardware
signals, or we can force it. The BXT code forces the nonexistent CL2 in
the x1 PHY to power down. Follow suit on CHV. Maybe it can still save
some extra power by disabling some extra logic in CL1, or something.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has supports some form of automagic clock gating for the
DPIO SUS clock. We can simply enable the magic bits and the
hardware should take care of the rest.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.
Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.
With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.
Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.
A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.
We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.
Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.
v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
fallout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: fix one error found by checkpath.pl
v3: Add one ignored break for switch-case. DDI-E hotplug
function doesn't work after updating drm-intel tree,
I checked the code and found this missing which isn't
the root cause for broke DDI-E hp. The broken
DDI-E hp function is fixed by "Adding DDI_E power
well domain".
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Timo Aaltonen <timo.aaltonen@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM instructions are not really
variable length instructions unlike MI_LOAD_REGISTER_IMM where it expects
(reg, addr) pairs so use fixed length for these instructions.
v2: rebase
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Appease checkpatch as Mika spotted in i915_reg.h - it seems
terminally unhappy about i915_cmd_parser.c so that would be a separate
patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turn on interrupt steering to route necessary interrupts to GuC.
v6:
Rebased
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fetches the required firmware image from the filesystem,
then loads it into the GuC's memory via a dedicated DMA engine.
This patch is derived from GuC loading work originally done by
Vinit Azad and Ben Widawsky.
v2:
Various improvements per review comments by Chris Wilson
v3:
Removed 'wait' parameter to intel_guc_ucode_load() as firmware
prefetch is no longer supported in the common firmware loader,
per Daniel Vetter's request.
Firmware checker callback fn now returns errno rather than bool.
v4:
Squash uC-independent code into GuC-specifc loader [Daniel Vetter]
Don't keep the driver working (by falling back to execlist mode)
if GuC firmware loading fails [Daniel Vetter]
v5:
Clarify WOPCM-related #defines [Tom O'Rourke]
Delete obsolete code no longer required with current h/w & f/w
[Tom O'Rourke]
Move the call to intel_guc_ucode_init() later, so that it can
allocate GEM objects, and have it fetch the firmware; then
intel_guc_ucode_load() doesn't need to fetch it later.
[Daniel Vetter].
v6:
Update comment describing intel_guc_ucode_load() [Tom O'Rourke]
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.
v2: Add missing ':' to the pipe config debug dump
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In 64b (48bit canonical) PPGTT addressing, the PDP0 register contains
the base address to PML4, while the other PDP registers are ignored.
In LRC, the addressing mode must be specified in every context
descriptor, and the base address to PML4 is stored in the reg state.
v2: PML4 update in legacy context switch is left for historic reasons,
the preferred mode of operation is with lrc context based submission.
v3: s/gen8_map_page_directory/gen8_setup_page_directory and
s/gen8_map_page_directory_pointer/gen8_setup_page_directory_pointer.
Also, clflush will be needed for bxt. (Akash)
v4: Squashed lrc-specific code and use a macro to set PML4 register.
v5: Rebase after Mika's ppgtt cleanup / scratch merge patch series.
PDP update in bb_start is only for legacy 32b mode.
v6: Rebase after final merged version of Mika's ppgtt/scratch
patches.
v7: There is no need to update the pml4 register value in
execlists_update_context. (Akash)
v8: Move pd and pdp setup functions to a previous patch, they do not
belong here. (Akash)
v9: Check USES_FULL_48BIT_PPGTT instead of GEN8_CTX_ADDRESSING_MODE in
gen8_emit_bb_start to check if emit pdps is needed. (Akash)
Cc: Akash Goel <akash.goel@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I started digging this when I noticed that the BDW code was just
reserving 1mb by coincidence since it was reading reserved fields.
Then I noticed we didn't have any values set for SNB and earlier, and
that the HSW sizes were wrong. After that, I noticed that the reserved
area has a specific start, and may not exactly end where the stolen
memory ends. I also noticed the base pointer can be zero. So I decided
to just write a single patch fixing everything instead of 20 patches
that would be much harder to review.
This patch may solve random stolen memory corruption/problems on
almost all platforms. Notice that since this is always dealing with
the top of the stolen memory, the problems are not so easy to
reproduce - especially since FBC is still disabled by default.
One of the major differences of this patch is that we now look at both
the size and base address. By only looking at the size we were
assuming that the reserved area was always at the very top of
stolen, which is not always true.
After we merge the patch series that allows user space to allocate
stolen memory we'll be able to write IGT tests that maybe catch the
bugs fixed by this patch.
v2:
- s/BIOS reserved/stolen reserved/g (Chris)
- Don't DRM_ERROR if we can't do anything about it (Chris)
- Improve debug messages (Chris).
- Use the gen7 version instead of gen6 on HSW. Tom found some
documentation problems, so I think with gen7 we're on the safer
side (Tom).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a requirement for enabling display port HPD support on the port
A HPD pin. This support is to be added by follow-up patches.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge fixes since it's getting out of hand again with the massive
split due to atomic between -next and 4.2-rc. All the bugfixes in
4.2-rc are addressed already (by converting more towards atomic
instead of minimal duct-tape) so just always pick the version in next
for the conflicts in modeset code.
All the other conflicts are just adjacent lines changed.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
drivers/gpu/drm/i915/intel_ringbuffer.h
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This change adds the programming of the MOCS registers to the gen 9+
platforms. The set of MOCS configuration entries introduced by this
patch is intended to be minimal but sufficient to cover the needs of
current userspace - i.e. a good set of defaults. It is expected to be
extended in the future to provide further default values or to allow
userspace to redefine its private MOCS tables based on its demand for
additional caching configurations. In this setup, userspace should
only utilize the first N entries, higher entries are reserved for
future use.
It creates a fixed register set that is programmed across the different
engines so that all engines have the same table. This is done as the
main RCS context only holds the registers for itself and the shared
L3 values. By trying to keep the registers consistent across the
different engines it should make the programming for the registers
consistent.
v2:
-'static const' for private data structures and style changes.(Matt Turner)
v3:
- Make the tables "slightly" more readable. (Damien Lespiau)
- Updated tables fix performance regression.
v4:
- Code formatting. (Chris Wilson)
- re-privatised mocs code. (Daniel Vetter)
v5:
- Changed the name of a function. (Chris Wilson)
v6:
- re-based
- Added Mesa table entry (skylake & broxton) (Francisco Jerez)
- Tidied up the readability defines (Francisco Jerez)
- NUMBER of entries defines wrong. (Jim Bish)
- Added comments to clear up the meaning of the tables (Jim Bish)
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
v7 (Francisco Jerez):
- Don't write L3-specific MOCS_ESC/SCC values into the e/LLC control
tables. Prefix L3-specific defines consistently with L3_ and
e/LLC-specific defines with LE_ to avoid this kind of confusion in
the future.
- Change L3CC WT define back to RESERVED (matches my hardware
documentation and the original patch, probably a misunderstanding
of my own previous comment).
- Drop Android tables, define new minimal tables more suitable for the
open source stack.
- Add comment that the MOCS tables are part of the kernel ABI.
- Move intel_logical_ring_begin() and _advance() calls one level down
(Chris Wilson).
- Minor formatting and style fixes.
v8 (Francisco Jerez):
- Add table size sanity check to emit_mocs_control/l3cc_table() (Chris
Wilson).
- Add comment about undefined entries being implicitly set to uncached
for forwards compatibility.
v9 (Francisco Jerez):
- Minor style fixes.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the spurious 'A' from the VLV/CHV ref clock enable define,
and add the "REF" to the VLV ref clock selection bit. Also
s/CLOCK/CLK/ for extra consistency.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this WA we need to set GEN8_L3SQCREG4[21:21] and reset it after PIPE_CONTROL
instruction but there is a slight complication as this is applied in WA batch
where the values are only initialized once.
Dave identified an issue with the current implementation where the register value
is read once at the beginning and it is reused; this patch corrects this by saving
the register value to memory, update register with the bit of our interest and
restore it back with original value.
This implementation uses MI_LOAD_REGISTER_MEM which is currently only used
by command parser and was using a default length of 0. This is now updated
with correct length and moved to appropriate place.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also clarify comments on context size that the extra state for
Resource Streamer is included.
v2: Don't remove the extended save/restore enabled for older
platforms. (Ville)
Use new MI_SET_CONTEXT defines for HSW RS save/restore state
instead of extended save/restore. (Daniel)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adds support for enabling the resource streamer on the legacy
ringbuffer for HSW and GEN8.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains changes based on 2 updates to the spec:
Port PLL VCO restriction raised up to 6700.
Port PLL now needs DCO amp override enable for all VCO frequencies.
v2: Sonika's review comment addressed
- dcoampovr_en_h variable not required
Based on a discussion with Siva, the following changes have been made.
- replace dco_amp var with #define BXT_DCO_AMPLITUDE
- set pll10 in a single assignment
v3:
Move DCO amplitude default value to i915_reg.h. Suggested by Siva.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com> [v2]
[danvet: Spell out BUN since not everyone knows what this means.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull intel drm fixes from Jani Nikula:
"Almost all of it is regression fixes all around, with cc: stable, and
then there's Ander's fix for one of the warnings you reported. We're
still working on the rest"
[ Dave is on vacation, and Jani is heading out on vacation too ]
* tag 'drm-intel-next-fixes-2015-07-02' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Clear pipe's pll hw state in hsw_dp_set_ddi_pll_sel()
drm/i915: fix backlight after resume on 855gm
agp/intel: Fix typo in needs_ilk_vtd_wa()
drm/i915/ppgtt: Break loop in gen8_ppgtt_clear_range failure path
drm/i915: Fix IPS related flicker
Add support for reading out the HW state for DDI ports. Since the actual
programming is very similar to the CHV/VLV DPIO PLL programming we can
reuse much of the logic from there.
This fixes the state checker failures I saw on my BXT with HDMI output.
v2:
- rebased on v2 of patch 4/5
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although we have a fixed setting for the PLL9 and EBB4 registers, it
still makes sense to check them together with the rest of PLL registers.
While at it also remove a redundant comment about 10 bit clock enabling.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some 855gm models (at least ThinkPad X40) regressed because of
commit b0cd324fae
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 12 16:25:43 2014 +0200
drm/i915: don't save/restore backlight hist ctl registers
which tried to make our driver more robust by not blindly saving and
restoring registers, but it failed to take into account
commit 0eb96d6ed3
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Oct 14 12:33:41 2009 -0700
drm/i915: save/restore BLC histogram control reg across suspend/resume
Fix the regression by enabling hist ctl on gen2.
v2: Improved the comment.
v3: Improved the comment, again.
Reported-and-tested-by: Philipp Gesang <phg@phi-gamma.net>
References: http://mid.gmane.org/20150623222648.GD12335@acheron
Fixes: b0cd324fae ("drm/i915: don't save/restore backlight hist ctl registers")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Consider which planes are active and compute the FIFO split based on the
relative data rates. Since we only consider the pipe src width rather
than the plane width when computing watermarks it seems best to do the
same when computing the FIFO split as well. This means the only thing we
actually have to consider for the FIFO splut is the bpp, and we can
ignore the rest.
I've just stuffed the logic into the watermark code for now. Eventually
it'll need to move into the atomic update for the crtc.
There's also one extra complication I've not yet considered; Some of the
DSPARB registers contain bits related to multiple pipes. The registers
are double buffered but apparently they update on the vblank of any
active pipe. So doing the FIFO reconfiguration properly when multiple
pipes are active is not going to be fun. But let's ignore that mess for
now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.2.
I've one other new driver from freescale on my radar, it's been posted
and reviewed, I'd just like to get someone to give it a last look, so
maybe I'll send it or maybe I'll leave it.
There is no major nouveau changes in here, Ben was working on
something big, and we agreed it was a bit late, there wasn't anything
else he considered urgent to merge.
There might be another msm pull for some bits that are waiting on
arm-soc, I'll see how we time it.
This touches some "of" stuff, acks are in place except for the fixes
to the build in various configs,t hat I just applied.
Summary:
New drivers:
- virtio-gpu:
KMS only pieces of driver for virtio-gpu in qemu.
This is just the first part of this driver, enough to run
unaccelerated userspace on. As qemu merges more we'll start
adding the 3D features for the virgl 3d work.
- amdgpu:
a new driver from AMD to driver their newer GPUs. (VI+)
It contains a new cleaner userspace API, and is a clean
break from radeon moving forward, that AMD are going to
concentrate on. It also contains a set of register headers
auto generated from AMD internal database.
core:
- atomic modesetting API completed, enabled by default now.
- Add support for mode_id blob to atomic ioctl to complete interface.
- bunch of Displayport MST fixes
- lots of misc fixes.
panel:
- new simple panels
- fix some long-standing build issues with bridge drivers
radeon:
- VCE1 support
- add a GPU reset counter for userspace
- lots of fixes.
amdkfd:
- H/W debugger support module
- static user-mode queues
- support killing all the waves when a process terminates
- use standard DECLARE_BITMAP
i915:
- Add Broxton support
- S3, rotation support for Skylake
- RPS booting tuning
- CPT modeset sequence fixes
- ns2501 dither support
- enable cmd parser on haswell
- cdclk handling fixes
- gen8 dynamic pte allocation
- lots of atomic conversion work
exynos:
- Add atomic modesetting support
- Add iommu support
- Consolidate drm driver initialization
- and MIC, DECON and MIPI-DSI support for exynos5433
omapdrm:
- atomic modesetting support (fixes lots of things in rewrite)
tegra:
- DP aux transaction fixes
- iommu support fix
msm:
- adreno a306 support
- various dsi bits
- various 64-bit fixes
- NV12MT support
rcar-du:
- atomic and misc fixes
sti:
- fix HDMI timing complaince
tilcdc:
- use drm component API to access tda998x driver
- fix module unloading
qxl:
- stability fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
drm/dp/mst: close deadlock in connector destruction.
drm: Always enable atomic API
drm/vgem: Set unique to "vgem"
of: fix a build error to of_graph_get_endpoint_by_regs function
drm/dp/mst: take lock around looking up the branch device on hpd irq
drm/dp/mst: make sure mst_primary mstb is valid in work function
of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/atomic: Don't set crtc_state->enable manually
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
...
Broxton is using a different register and different bit ordering
for rps status capabilities.
Also GT perf freqency register is different for Broxton so update
that.
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Indirect context w/a batch buffer,
WaClearSlmSpaceAtContextSwitch
This WA performs writes to scratch page so it must be valid, this check
is performed before initializing the batch with this WA.
v2: s/PIPE_CONTROL_FLUSH_RO_CACHES/PIPE_CONTROL_FLUSH_L3 (Ville)
v3: GTT bit in scratch address should be mbz (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Indirect context w/a batch buffer,
+WaFlushCoherentL3CacheLinesAtContextSwitch:bdw
v2: Add LRI commands to set/reset bit that invalidates coherent lines,
update WA to include programming restrictions and exclude CHV as
it is not required (Ville)
v3: Avoid unnecessary read when it can be done by reading register once (Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order for gen8+ hardware to guarantee that no context switch
takes place during engine reset and that current context is properly
saved, the driver needs to notify and query hw before commencing
with reset.
There are gpu hangs where the engine gets so stuck that it never will
report to be ready for reset. We could proceed with reset anyway, but
with some hangs with skl, the forced gpu reset will result in a system
hang. By inspecting the unreadiness for reset seems to correlate with
the probable system hang.
We will only proceed with reset if all engines report that they
are ready for reset. If root cause for system hang is found and
can be worked around with another means, we can reconsider if
we can reinstate full reset for unreadiness case.
v2: -EIO, Recovery, gen8 (Chris, Tomas, Daniel)
v3: updated commit msg
v4: timeout_ms, simpler error path (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=89959
References: https://bugs.freedesktop.org/show_bug.cgi?id=90854
Testcase: igt/gem_concurrent_blit/prw-blt-overwrite-source-read-rcs-forked
Testcase: igt/gem_concurrent_blit/gtt-blt-overwrite-source-read-rcs-forked
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tomas Elf <tomas.elf@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Changes for BXT - added a IS_BROXTON check to use the macro related to PPS
registers for BXT.
BXT does not have PP_DIV register. Making changes to handle this.
Second set of PPS registers have been defined but will be used when VBT
provides a selection between the 2 sets of registers.
v2:
[Jani] Added 2nd set of PPS registers and the macro
Jani's review comments
- remove reference in i915_suspend.c
- Use BXT PP macro
Squashing all PPS related patches into one.
v3: Jani's review comments addressed
- Use pp_ctl instead of pp
- ironlake_get_pp_control() is not required for BXT
- correct the use of && in the print statement
- drop the shift in the print statement
v4: Jani's comments
- modify ironlake_get_pp_control() - dont set unlock key for bxt
v5: Sonika's comments addressed
- check alignment
- move pp_ctrl_reg write (after ironlake_get_pp_control())
to !IS_BROXTON case.
- check before subtracting 1 for t11_t12
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already had a few bugs in the past where FBC was compressing
nothing when it was enabled, which makes the feature quite useless.
Add this information to debugfs so the test suites can check for
regressions in this piece of the code.
Our igt/tests/kms_frontbuffer_tracking already has support for this
message.
v2: - Remove pointless VLV check (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GCP infoframes are required to inform the HDMI sink about the color
depth.
Send the GCP infoframe whenever the sink supports any deep color modes
since such sinks must anyway be capable of receiving them. For sinks
that don't support deep color let's skip the GCP in case it might
confuse the sink, although HDMI 1.4 spec does say all sinks must be
capable of reciving them. In theory we could skip the GCP infoframe
for deep color sinks in 8bpc mode as well since sinks must fall back to
8bpc whenever GCP isn't received for some time.
BSpec says we should disable GCP after disabling the port, so do that as
well.
v2: s/intel_set_gcp_infoframe/intel_hdmi_set_gcp_infoframe/
Rebased due to crtc->config changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict with lack of chv phy patches and fixup typo
Chandra spotted.]
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CPT/PPT require a specific procedure for enabling 12bpc HDMI. Implement
it, and to keep things neat pull the code into a function.
v2: Rebased due to crtc->config changes
s/HDMI_GC/HDMIUNIT_GC/ to match spec better
Factor out intel_enable_hdmi_audio()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-By: Chandra Konduru <Chandra.konduru@intel.com>
Testecase: igt/kms_render/*
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for changing cdclk frequency during runtime on BDW.
Also with IPS enabled the actual pixel rate mustn't exceed 95% of cdclk,
so take that into account when computing the max pixel rate.
v2: Grab rps.hw_lock around sandybridge_pcode_write()
v3: Rebase due to power well vs. .global_resources() reordering
v4: Rebased to the latest
v5: Rebased to the latest
v6: Patch order shuffle so that Broadwell CD clock change is
applied before the patch for Haswell CD clock change
v7: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Implement cdclk extraction for g33, 965gm and g4x platforms. The details
came from configdb. Sadly there isn't anything there for other gen3/gen4
chipsets.
So far I've tested this on one ELK where it gave me a HPLL VCO of 5333
MHz and cdclk of 444 MHz which seems perfectly sane for this machine.
v2: Rebased to the latest
v3: Rebased to the latest
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Actually read the HPLLCC register insted of assuming it's 0. Fix the
HPLLCC bit definitions and all the missing ones from the 852GME spec.
852GME, 854 and 855 all seem to match the same HPLLC encoding even
though only some of the values are valid is some of the platforms.
v2: Rebased to the latest
v3: Rebased to the latest
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Expecting CHV power wells to be just an extended versions of the VLV
power wells, a bunch of commented out power wells were added in
anticipation when Punit folks would implement it all. Turns out they
never did, and instead CHV has fewer power wells than VLV. Rip out all
the #if 0'ed junk that's not needed.
v2: Rename the "pipe-a" well to "display" to match VLV
Clarify the pipe A power well relationship to pipes B and C (Deepak)
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not sure which LDO programming sequence delay should be used for the CHV
PHY, but the spec says that 600ns is "Used by default for initial
bringup", and the BIOS seems to use that, so let's do the same.
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GTT caching was disabled by default on gen8 due to not working with
big pages. Some information suggests that it got fixed, but still
GTT caching has been left disabled by default. Or could be it just
meant that the default was changed to off, and hence the problem
got solved.
Enable GTT caching in the hopes of some performance increase.
Whether or not the big pages issue has been fixed is irrelevant
at this stage since we don't use big pages.
This gives me a 1-2% improvement in xonotic on my BSW. Haven't tried
BDW, but supposedly it has larger TLBs so might not benefit as much.
On HSW GTT caching is enabled by default.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Define a TRANS_DP_PIPE_TO_PORT() to make the CPT DP .get_hw_state()
pipe readout neater.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init the display hardware when going out of suspend. This
includes:
- Hooking the PCH to the reset logic
- Restoring CDCDLK
- Enabling the DDB power
Among those, only the CDCDLK one is a bit tricky. There's some
complexity in that:
- DPLL0 (which is the source for CDCLK) has two VCOs, each with a set
of supported frequencies. As eDP also uses DPLL0 for its link rate,
once DPLL0 is on, we restrict the possible eDP link rates the chosen
VCO.
- CDCLK also limits the bandwidth available to push pixels.
So, as a first step, this commit restore what the BIOS set, until I can
do more testing.
In case that's of interest for the reviewer, I've unit tested the
function that derives the decimal frequency field:
#include <stdio.h>
#include <stdint.h>
#include <assert.h>
#define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x)))
static const struct dpll_freq {
unsigned int freq;
unsigned int decimal;
} freqs[] = {
{ .freq = 308570, .decimal = 0b01001100111},
{ .freq = 337500, .decimal = 0b01010100001},
{ .freq = 432000, .decimal = 0b01101011110},
{ .freq = 450000, .decimal = 0b01110000010},
{ .freq = 540000, .decimal = 0b10000110110},
{ .freq = 617140, .decimal = 0b10011010000},
{ .freq = 675000, .decimal = 0b10101000100},
};
static void intbits(unsigned int v)
{
int i;
for(i = 10; i >= 0; i--)
putchar('0' + ((v >> i) & 1));
}
static unsigned int freq_decimal(unsigned int freq /* in kHz */)
{
return (freq - 1000) / 500;
}
static void test_freq(const struct dpll_freq *entry)
{
unsigned int decimal = freq_decimal(entry->freq);
printf("freq: %d, expected: ", entry->freq);
intbits(entry->decimal);
printf(", got: ");
intbits(decimal);
putchar('\n');
assert(decimal == entry->decimal);
}
int main(int argc, char **argv)
{
int i;
for (i = 0; i < ARRAY_SIZE(freqs); i++)
test_freq(&freqs[i]);
return 0;
}
v2:
- Rebase on top of -nightly
- Use (freq - 1000) / 500 for the decimal frequency (Ville)
- Fix setting the enable bit of HSW_NDE_RSTWRN_OPT (Ville)
- Rename skl_display_{resume,suspend} to skl_{init,uninit}_cdclk to
be consistent with the BXT code (Ville)
- Store boot CDCLK in ddi_pll_init (Ville)
- Merge dev_priv's skl_boot_cdclk into cdclk_freq
- Use LCPLL_PLL_LOCK instead of (1 << 30) (Ville)
- Replace various '0' by SKL_DPLL0 to be a bit more explicit that
we're programming DPLL0
- Busy poll the PCU before doing the frequency change. It takes about
3/4 cycles, each separated by 10us, to get the ACK from the CPU
(Ville)
v3:
- Restore dev_priv->skl_boot_cdclk, leaving unification with
dev_priv->cdclk_freq for a later patch (Daniel, Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On B0 and C0 steppings the workaround enable bit would be overriden by
default, so the overriding must be disabled.
The WA was added in
commit 83a24979c4
Author: Nick Hoath <nicholas.hoath@intel.com>
Date: Fri Apr 10 13:12:26 2015 +0100
drm/i915/bxt: Add WaForceContextSaveRestoreNonCoherent
Spotted-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BUN 1: prop_coeff, int_coeff, tdctargetcnt programming updated and tied to
VCO frequencies. Program i_lockthresh in PORT_PLL_9.
VCO calculated based on the formula:
Desired Output = Port bit rate in MHz (DisplayPort HBR2 is 5400 MHz)
Fast Clock = Desired Output / 2
VCO = Fast Clock * P1 * P2
Prop_coeff, int_coeff, and tdctargetcnt modified according to above
calculation.
BUN 2: Port PLLs require additional programming at certain frequencies -
DCO amplitude in PORT_PLL_10
Review comments from Siva which were addressed in the initial version of the
patch.
- Change PORT_PLL_LOCK_THRESHOLD to PORT_PLL_LOCK_THRESHOLD_MASK
- Calculate for HDMI
- Correct values for vco = 5.4
- return in case of invalid vco range
v2: Imre's review comments addressed
- change dcoampovr_en to dcoampovr_en_h
- change PORT_PLL_DCO_AMP_OVR_EN to PORT_PLL_DCO_AMP_OVR_EN_H
- Correct lane stagger value for 324MHz
- Make coef common for HDMI and DP
- remove superfluous comments
v3: Imre's comments addressed
- Remove Prop_coeff, int_coeff, tdctargetcnt, dcoampovr_en, gain_ctl,
dcoampovr_en_h from bxt_clk_div and make them local variables.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> [v1]
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake nv12 format requires dbuf (aka. ddb) calculations
and programming for each of y and uv sub-planes. Made minor
changes to reuse current dbuf calculations and programming
for uv plane. i.e., with this change, existing computation
is used for either packed format or uv portion of nv12
depending on incoming format. Added new code for dbuf
computation and programming for y plane.
This patch is a pre-requisite for adding NV12 format support.
Actual nv12 support is coming in later patches.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sometimes (exactly when is a bit unclear) DISPLAY_PHY_CONTROL appears to
get corrupted. The values I've managed to read from it seem to have some
pattern but vary quite a lot. The corruption doesn't seem to just happen
when the register is accessed, but can also happen spontaneosly during
modeset. When this happens during a modeset things go south and the
display doesn't light up.
I've managed to hit the problemn when toggling HDMI on port D on and
off. When things get corrupted the display doesn't light up, but as soon
as I manually write the correct value to the register the display comes
up.
First I was suspicious that we ourselves accidentally overwrite it with
garbage, but didn't catch anything with the reg_rw tracepoint. Also I
sprinkled check all over the modeset path to see exactly when the
corruption happens, and eg. the read back value was fine just before
intel_dp_set_m(), and corrupted immediately after it. I also made my
check function repair the register value whenever it was wrong, and with
this approach the corruption repeated several times during the modeset
operation, always seeming to trigger in the same exact calls to the
check function, while other calls to the function never caught anything.
So far I've not seen this problem occurring when carefully avoiding all
read accesses to DISPLAY_PHY_CONTROL. Not sure if that's just pure luck
or an actual workaround, but we can hope it works. So let's avoid reading
the register and instead track the desired value of the register in dev_priv.
v2: Read out the power well state to determine initial register value
v3: Use DPIO_CHx names instead of raw numbers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set up the chv display PHY lane stagger registers according to
"Programming Guide for 1273 CHV eDP/DP/HDMI Display PHY" v1.04
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Robert noticed that the FF_SLICE_CS_CHICKEN2 offset was wrong. Ooops.
Ville noticed that the write was wrong since FF_SLICE_CS_CHICKEN2 is a
masked register. Re-oops.
A wonder if went through 2 people while having roughly a bug per line...
The problem was introduced in the original patch:
commit 2caa3b260a
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Mon Feb 9 19:33:20 2015 +0000
drm/i915/skl: Implement WaDisableChickenBitTSGBarrierAckForFFSliceCS
v2: Also fix the register write (Ville)
Reported-by: Robert Beckett <robert.beckett@intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Robert Beckett <robert.beckett@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note that we also need this for skl.
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Note that we also need this for skl, requested by Imre.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enabling BLC on BXT.
Includes register definition, and new functions for BXT.
In BXT, there are 2 sets of registers for BLC. Until there is clarity
about which set would be effective, set 1 is being used.
This would have to be re-visited if there is any change or when 2 LFPs are
enabled on BXT.
This patch enables brightness change which would be effected by use of
hot-keys or sysfs entry.
TODO:- BLC implementation will have to re-visited when
1. there is clarity about which set of registers has to be used and when.
2. CDCLK frequency is changed
v2: Jani's review comments
- Modified comment in i915_reg.h
- Renamed register defintions
- Removed definition of duty cycle max. Not required now and its not 64-bit.
v3:
- Rebase on top of VLV/CHV backlight changes, in particuliar
bxt_set_backlight() now has a different prototype (Damien)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Shankar, Uma <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's keep that list sorted!
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the spec, Setting up static BIAS for GPU to improve the
rps performace.
v2: rename reg defn to match spec. (Ville)
v3: Updated bias setting for chv (Deepak)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch just implements the basic enable and disable
functions of DC5 state which is needed for both SKL and BXT.
Its important to load respective CSR program before calling
enable, which anyways will happen as CSR program is executed
during boot.
DC5 is a power saving state where hardware dynamically disables
power well 1 and the CDCLK PLL and saves the associated registers.
DC5 can be entered when software allows it, power well 2 is
disabled, and hardware detects that all pipes are disabled
or pipe A is enabled with PSR active.
Its better to configure display engine to have power well 2 disabled before
getting into DC5 enable function. Hence rpm framework will have to
ensure to check status of power well 2 before calling gen9_enable_dc5.
Rather dc5 entry criteria should be decided based on power well 2 status.
If disabled, then call gen9_enable_dc5.
v2: Replace HAS_ with IS_ check as per Daniel's review comments
v3: Cleared the bits dc5/dc6 enable of DC_STATE_EN register
before setting them as per Satheesh's review comments.
v4: call POSTING_READ for every write to a register to ensure that
its written immediately.
v5: Modified as per review comments from Imre.
- Squashed register definitions into this patch.
- Finetuned comments and functions.
v6:
Avoid redundant writes in gen9_set_dc_state_debugmask_memory_up function.
v7:
- Rebase to latest.
- Move all runtime PM functions defined in intel_display.c to
intel_runtime_pm.c.
v8: Rebased to drm-intel-nightly. (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2015-04-23:
- dither support for ns2501 dvo (Thomas Richter)
- some polish for the gtt code and fixes to finally enable the cmd parser on hsw
- first pile of bxt stage 1 enabling (too many different people to list ...)
- more psr fixes from Rodrigo
- skl rotation support from Chandra
- more atomic work from Ander and Matt
- pile of cleanups and micro-ops for execlist from Chris
drm-intel-next-2015-04-10:
- cdclk handling cleanup and fixes from Ville
- more prep patches for olr removal from John Harrison
- gmbus pin naming rework from Jani (prep for bxt)
- remove ->new_config from Ander (more atomic conversion work)
- rps (boost) tuning and unification with byt/bsw from Chris
- cmd parser batch bool tuning from Chris
- gen8 dynamic pte allocation (Michel Thierry, based on work from Ben Widawsky)
- execlist tuning (not yet all of it) from Chris
- add drm_plane_from_index (Chandra)
- various small things all over
* tag 'drm-intel-next-2015-04-23-fixed' of git://anongit.freedesktop.org/drm-intel: (204 commits)
drm/i915/gtt: Allocate va range only if vma is not bound
drm/i915: Enable cmd parser to do secure batch promotion for aliasing ppgtt
drm/i915: fix intel_prepare_ddi
drm/i915: factor out ddi_get_encoder_port
drm/i915/hdmi: check port in ibx_infoframe_enabled
drm/i915/hdmi: fix vlv infoframe port check
drm/i915: Silence compiler warning in dvo
drm/i915: Update DRIVER_DATE to 20150423
drm/i915: Enable dithering on NatSemi DVO2501 for Fujitsu S6010
rm/i915: Move i915_get_ggtt_vma_pages into ggtt_bind_vma
drm/i915: Don't try to outsmart gcc in i915_gem_gtt.c
drm/i915: Unduplicate i915_ggtt_unbind/bind_vma
drm/i915: Move ppgtt_bind/unbind around
drm/i915: move i915_gem_restore_gtt_mappings around
drm/i915: Fix up the vma aliasing ppgtt binding
drm/i915: Remove misleading comment around bind_to_vm
drm/i915: Don't use atomics for pg_dirty_rings
drm/i915: Don't look at pg_dirty_rings for aliasing ppgtt
drm/i915/skl: Support Y tiling in MMIO flips
drm/i915: Fixup kerneldoc for struct intel_context
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
Add support for enabling codec wakeup override signal to allow
re-enumeration of the controller on SKL after resume from low power state.
In SKL, HDMI/DP codec and PCH HD Audio Controller are in different power
wells, so it's necessary to reset display audio codecs when power well on,
otherwise display audio codecs will disappear when resume from low power
state.
Reset steps when power on:
enable codec wakeup -> azx_init_chip() -> disable codec wakeup
v3 by Jani: Simplify to only support toggling the appropriate chicken bit.
v4 by Han: add explanation and specify the hw swquence.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This WA is avoid problem between shadow vs wake FIFO unload
problem during CPD/RC6 transactions on CHV.
v2: Define individual bits GTFIFOCTL (Ville)
v3: move WA to uncore_early_sanitize (ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: fixed some whitespace issues while applying]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The hardware, according to the specs, is limited to 256 byte transfers,
and current driver has no protections in case users attempt to do larger
transfers. The code will just stomp over status register and mayhem
ensues.
Let's split larger transfers into digestable chunks. Doing this allows
Atmel MXT driver on Pixel 1 function properly (it hasn't since commit
9d8dc3e529 "Input: atmel_mxt_ts -
implement T44 message handling" which tries to consume multiple
touchscreen/touchpad reports in a single transaction).
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
VSwing programming sequence as specified in the updated BXT BSpec
v2: Satheesh's review comments addressed.
- clear value before setting into registers
- move print statement to bxt function
Other changes
- since signal level will not be set into DDI_BUF_CTL, the value need
not be returned to intel_dp_set_signal_levels(). Making the bxt
specific function to return void and setting signal_levels = 0 for
bxt inside intel_dp_set_signal_levels()
- instead of signal levels, printing vswing level and pre-emphasis
level
- in case none of the pre-emphasis levels or vswing levels are set,
setting default of 400mV + 0dB
v3: Satheesh's review comments
- Check for mask before printing signal_levels.
- Removing redundant register writes
- Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT
- Making register write part generic as it will be required for HDMI as
well.
Re-structure the code to include an array for vswing related values, set
signal levels
v4: Satheesh's review comments
- Rebase over latest renaming patches
- use hsw_signal_levels for HAS_DDI
Other changes
- Modified vswing_sequence() func definition
- Rebased on top of register macro definitions
v5: Satheesh's review comments
- Check ddi translation table size
v6: Imre's review comments
- removed comments in vswing sequence
- added vswing, pre-emphasis prints in intel_dp_set_signal_levels
- added comment explaining use of DP vswing values for eDP
- initialize n_entries and ddi_transaltion table based on encoder type
- create bxt_ddi_buf_trans structure and use decimal values
- adding a flag in bxt buffer translation table to indicate def entry
v7: (imre)
- squash in Vandana's "VSwing register definition",
"HDMI VSwing programming", "Re-enable vswing programming",
"Fix vswing sequence" patches
- use BXT_PORT_* regs directly instead of via a temp var
- simplify BXT_PORT_* macro definitions
- add code comment why we read lane while write group registers
- fix readout of DP_TRAIN_PRE_EMPHASIS in debug message
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Plug bxt PLL code into existing shared DPLL framework.
v2: (imre)
- squash in Satheeshakrishna's "Define BXT clock registers" and
"Add state variables for bxt clock registers" patches
- squash in Vandanas's "Change grp access to lane access for PLL"
- fix group vs. lane access in bxt_ddi_pll_get_hw_state
- add code comment why we read from lane registers while writing to
group registers
- clean up register macros
- use BXT_PORT_PLL_* macros instead of open-coding the same
- check if BXT_PORT_PCS_DW12_LN01 matches BXT_PORT_PCS_DW12_LN23
during hardware state readout
- add missing LANESTAGGER_STRAP_OVRD masking
- add note about missing step according to the latest BUN for
PORT_PLL_9/lockthresh
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Modified as per review comments from Imre
- Mention enabling instead of allowing in the debug trace and
remove unnecessary comments.
v3:
- Rebase to latest.
- Move DC9-related functions from intel_display.c to intel_runtime_pm.c.
v4: (imre)
- remove DC5 disabling, it's a nop at this point
- squashed in Suketu's "Assert the requirements to enter or exit DC9"
patch
- remove check for RUNTIME_PM from assert_can_enable_dc9, it's not a
dependency
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com> (v3)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extend the VLV/CHV DPIO (PHY) documentation with the BXT specifics.
v2:
- add more detail about the mapping between ports and transcoders (ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add PHY specific display initialization sequence as per BSpec.
Note that the PHY initialization/uninitialization are done
at their current place only for simplicity, in a future patch - when more
of the runtime PM features will be enabled - these will be moved to
power well#1 and modeset encoder enabling/disabling hooks respectively.
The call to uninitialize the PHY during system/runtime suspend will be
added later in this patchset.
v1: Added function definitions in header files
v2: Imre's review comments addressed
- Moved CDCLK related definitions to i915_reg.h
- Removed defintions for CDCLK frequency
- Split uninit_cdclk() by adding a phy_uninit function
- Calculate freq and decimal based on input frequency
- Program SSA precharge based on input frequency
- Use wait_for 1ms instead 200us udelay for DE PLL locking
- Removed initial value for divider, freq, decimal, ratio.
- Replaced polling loops with wait_for
- Parameterized latency optim setting
- Fix the parts where DE PLL has to be disabled.
- Call CDCLK selection from mode set
v3: (imre)
- add note about the plan to move the cdclk/phy init to a better place
- take rps.hw_lock around pcode access
- fix DDI PHY timeout value
- squash in Vandana's "PORT_CL2CM_DW6_A BUN fix",
"DDI PHY programming register defn", "Do ddi_phy_init always",
- move PHY register macros next to the corresponding CHV/VLV macros
- move DE PLL register macros here from another patch since they are
used here first
- add BXT_ prefix to CDCLK flags
- s/COMMON_RESET/COMMON_RESET_DIS/ and clarify related code comments
- fix incorrect read value for the RMW of BXT_PHY_CTL_FAMILY_DDI
- fix using GT_DISPLAY_EDP_POWER_ON vs. GT_DISPLAY_DDI_POWER_ON
when powering on DDI ports
- fix incorrect port when setting BXT_PORT_TX_DW14_LN for DDI ports
- add missing masking when programming CDCLK_FREQ_DECIMAL
- add missing powering on for DDI-C port, rename OCL2_LDOFUSE_PWR_EN
to OCL2_LDOFUSE_PWR_DIS to reduce confusion
- add note about mismatch with bspec in the PORT_REF_DW6 fields
- factor out PHY init code to a new function, so we can call it for
PHY1 and PHY0, instead of open-coding the same
v4: (ville)
- split the CDCLK/PHY parts into two patches, update commit message
accordingly
- use the existing dpio_phy enum instead of adding a new one for the
same purpose
- flip the meaning of PHYs so that PHY_A is PHY1 and PHY_BC is PHY0 to
better match CHV
- s/BXT_PHY/_BXT_PHY/
- use _PIPE for _BXT_PHY instead of open-coding it
- drop _0_2_0_GTTMMADR suffix from BXT_P_CR_GT_DISP_PWRON
- define GT_DISPLAY_POWER_ON in a more standard way
- make a note that the CHV ConfigDB also disagrees about GRC_CODE field
definitions
- fix lane optimization refactoring fumble from v3
- add per PHY uninit functions to match the init counterparts
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add CDCLK specific display clock initialization sequence as per BSpec.
Note that the CDCLK initialization/uninitialization are done at their
current place only for simplicity, in a future patch - when more of the
runtime PM features will be enabled - these will be moved to power
well#1 and modeset encoder enabling/disabling hooks respectively. This
also means that atm dynamic power gating power well #1 is effectively
disabled.
The call to uninitialize CDCLK during system/runtime suspend will be
added later in this patchset.
v1: Added function definitions in header files
v2: Imre's review comments addressed
- Moved CDCLK related definitions to i915_reg.h
- Removed defintions for CDCLK frequency
- Split uninit_cdclk() by adding a phy_uninit function
- Calculate freq and decimal based on input frequency
- Program SSA precharge based on input frequency
- Use wait_for 1ms instead 200us udelay for DE PLL locking
- Removed initial value for divider, freq, decimal, ratio.
- Replaced polling loops with wait_for
- Parameterized latency optim setting
- Fix the parts where DE PLL has to be disabled.
- Call CDCLK selection from mode set
v3: (imre)
- add note about the plan to move the cdclk/phy init to a better place
- take rps.hw_lock around pcode access
- move DE PLL register macros here from another patch since they are
used here first
- add BXT_ prefix to CDCLK flags
- add missing masking when programming CDCLK_FREQ_DECIMAL
v4: (ville)
- split the CDCLK/PHY parts into two patches, update commit message
accordingly
- s/DISPLAY_PCU_CONTROL/HSW_PCODE_DE_WRITE_FREQ_REQ/
- simplify BXT_DE_PLL_RATIO macros
- fix BXT_DE_PLL_RATIO_MASK
- s/bxt_select_cdclk_freq/broxton_set_cdclk_freq/
- move cdclk init/uninit/set code from intel_ddi.c to intel_display.c
- remove redundant code comments for broxton_set_cdclk_freq()
- sanitize fixed point<->integer frequency value conversion
- use DRM_ERROR instead of WARN
- do RMW when programming BXT_DE_PLL_CTL for safety
- add note about PLL lock timeout being exactly 200us
- make PCU error messages more descriptive
- instead of using 0 freq to mean PLL off/bypass freq use 19200
for clarity, as the latter one is the actual rate
- simplify pcode programming, removing duplicated
sandybridge_pcode_write() call
- sanitize code flow, remove unnecessary scratch vars in
broxton_set_cdclk() (imre)
- Remove bound check for maxmimum freq to match current code.
This check will be added later at a more proper platform
independent place once atomic support lands.
- add note to remove freq guard band which isn't needed on BXT
- add note to reduce freq to minimum if no pipe is enabled
- combine broxton_modeset_global_pipes() with
valleyview_modeset_global_pipes()
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This wrong logic and useless define came from first versions and
came along with all rework. Just now I notice how ugly, wrong and
useless this is.
val is already defined as 0 anyway and logic is completelly wrong
and useless. So let's starting the link_standby fix with this
cleaning.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GMBUS interrupt has been moved to CPU side in BXT.
What this patch does is:
1. Enable GMBUS IRQ in de_post_install function
2. Handle this interrupt as a port interrupt in display irq
handler
v2: Rebase on top of the for_each_pipe() change adding dev_priv as
first argument (Damien).
v3: read BXT_DE_PORT_GMBUS IIR flag only on BXT on other platforms
it's reserved (imre)
v4: (jani)
- remove redundant 'BXT GMBUS' comment
- fix formatting of BXT_DE_PORT_GMBUS definition
Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In BXT, DDI hotplug control has been moved to CPU from PCH.
This patch adds a new IRQ setup function for BXT which:
1. Checks which HPD ports are requested to be enabled by encoders.
2. Enables those ports in the hot plug control register.
3. Un-masks these port interrupts in the IMR register.
4. Enables these port interrupts in the IER register.
V3: Kept the default HPD filter count to default (500 us) as per
satheesh's comment
v4: Remove unused HPD filter defines (Damien)
v5: warn if trying to setup HPD on port A (imre)
v6: fix order of definitions for register bitfields (Daniel)
v7: (jani)
- define the size of the hpd_bxt array explicitly for bound checking
- use for_each_intel_encoder instead of open coding it
- fix format/order of definitions for BXT_HOTPLUG_CTL reg bitfields
Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> (v4)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For BXT gmbus is pulled from PCH to CPU. From implementation point of
view only pin pair configuration will change. The existing
implementation supports all platforms previous to GEN8 and also SKL. But
for BXT pin pair configuration is completely different than SKL or other
previous GEN's. This patch introduces the new pin pair configuration
structure specific to BXT and also ensures every real gmbus port has a
gpio pin.
v3 by Jani: with the platform independent prep work in place, the bxt
enabling reduces to a fairly trivial patch. Credits are due Sunil for
giving me the ideas (with his patches) what the platform independent
parts should look like.
v4: Fix intel_hdmi_init_connector() for bxt. Abstract gmbus_pin access
more. s/GPU/PCH/ in commit message.
v5: Rebase.
Issue: VIZ-3574
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Separate topic branch for bxt didn't work out since we needed to
refactor the gmbus code a bit to make it look decent. So backmerge.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Set TLBPF in TILECTL. This fixes an issue with BXT HW seeing
corrupted pte entries.
v2:
- move the workaround to bxt_init_clock_gating (imre)
Signed-off-by: Robert Beckett <robert.beckett@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Moving creation of property in a function, checking for 90/270
rotation simultaneously (Chris)
Letting primary plane to be positioned
v3: Adding if/else for 90/270 and rest params programming, adding check for
pixel_format, some cleanup (review comments)
v4: Adding right pixel_formats, using src_* params instead of crtc_* for offset
and size programming (Ville)
v5: Rebased on -nightly and Tvrtko's series for gtt remapping.
v6: Rebased on -nightly (Tvrtko's series merged)
v7: Moving pixel_format check to intel_atomic_plane_check (Matt)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reuse the same reclocking strategy for Baytail as on its bigger brethren,
Sandybridge and Ivybridge. In particular, this makes the device quicker
to reclock (both up and down) though the tendency now is to downclock
more aggressively to compensate for the RPS boosts.
v2: Rebase
v3: Exclude Cherrytrail as Deepak was concerned that the increased
number of register writes would wake the common powerwell too often.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Modify the Gen9 SSEU device status logic to support Broxton.
Broxton reuses the Skylake power gate acknowledgment registers but
has at most 1 slice and 3 subslices. Broxton supports subslice
power gating within its single slice.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Modify the Gen9 SSEU info initialization logic to support
Broxton. Broxton reuses the SKL fuse registers but has at most
1 slice and 6 EU per subslice.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Program the default initial value of the L3SqcReg1 on BDW for performance
v2: Default confirmed and using intel_ring_emit_wa as Mika pointed out.
v3: Spec shows now a different value. It tells us to set to 0x784000
instead the 0x610000 that is there already.
Also rebased after a long time so using WA_WRITE now.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We make use of HW tracking for Selective update region and enable frame sync on
sink. We use hardware's hardcoded data values for frame sync and GTC.
v2: Add 3200x2000 resolution restriction with PSR2, move psr2_support to i915_psr
struct, add aux_frame_sync to independently control aux frame sync, rename the
TP2 TIME macro for 2500us (Rodrigo, Siva)
v3: Moving the resolution restriction to intel_psr_enable so that we check it
only once(Durga)
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Index the gmbus tables directly using the pin instead of having a
confusing "port = i + 1" mapping. This finishes off removing the "gmbus
port" as a notion, and leaves us with just the "gmbus pin".
As pin 0 is invalid by definition and the gmbus tables will have a gap
at that index, add pin validity check to all the loops. This will be
benefitial for supporting platforms that have different numbers of pins,
or gaps.
v2: s/GMBUS_PIN_MAX/GMBUS_NUM_PINS/ (Ville, Daniel)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs refer to pin pairs. Start moving towards using pin rather than
port all around to avoid confusion. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The faulting virtual address is >32bits and has been moved
to different registers. Add to error state and output upper
register first, in the same line for easy reconstruction of
the fault address.
v2: correct gen masking (Michel)
v3: s/TBL/TLB (Ville)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use both up/down manual ei calcuations for symmetry and greater
flexibility for reclocking, instead of faking the down interrupt based
on a fixed integer number of up interrupts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite commit 31685c258e
Author: Deepak S <deepak.s@linux.intel.com>
Date: Thu Jul 3 17:33:01 2014 -0400
drm/i915/vlv: WA for Turbo and RC6 to work together.
Other than code clarity, the major improvement is to disable the extra
interrupts generated when idle. However, the reclocking remains rather
slow under the new manual regime, in particular it fails to downclock as
quickly as desired. The second major improvement is that for certain
workloads, like games, we need to combine render+media activity counters
as the work of displaying the frame is split across the engines and both
need to be taken into account when deciding the global GPU frequency as
memory cycles are shared.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For SKL, register definition for RPNSWREQ (A008), RPSTAT1(A01C)
have changed slightly. Also on SKL, frequency is specified in
units of 16.66 MHZ, compared to 50 MHZ for most of the earlier
platforms and the time values are expressed in units of 1.33 us,
compared to 1.28 us for earlier platforms.
Added new macros for the aforementioned changes.
v2: Renamed the GT_FREQ_FROM_PERIOD macro to GT_INTERVAL_FROM_US (Damien)
v3: Removed the implicit use of dev_priv in GT_INTERVAL_FROM_US macro (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the FW_WM() macro from the VLV wm code to polish up the wm
code for older gmch platforms.
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wrap the FW register value shift+mask operations into a macro to hide
the ugliness a bit. Also might avoid bugs due to typos.
Also rename all the primary/sprite plane low order bit masks to have the
_VLV suffix, so that we can use the FW_WM_VLV() macro instead of the
FW_WM() macro for them in a consistent manner. Cursor and all the high
order bits are left to use the FW_WM() macro as there's no real
confusion with them.
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DDR DVFS introduces massive memory latencies which can't be handled by
the PND deadline stuff. Instead the watermarks will need to be
programmed to compensate for the latency and the deadlines will need to
be programmed to tight fixed values. That means DDR DVFS can only be
enabled if the display FIFOs are large enough, and that pretty much
means we have to manually repartition them to suit the needs of the
moment.
That's a lot of change, so in the meantime let's just disable DDR DVFS
to get the display(s) to be stable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has a new knob in Punit to select between some memory power savings
modes PM2 and PM5. We can allow the deeper PM5 when maxfifo mode is
enabled, so let's do so in the hopes for moar power savings.
v2: Put the thing into a separate function to avoid churn later
v3: Don't break VLV
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PFI credit programming is required when CD clock (related to data flow from
display pipeline to end display) is greater than CZ clock (related to data
flow from memory to display plane). This programming should be done when all
planes are OFF to avoid intermittent hangs while accessing memory even from
different Gfx units (not just display).
If cdclk/czclk >=1, PFI credits could be set as any number. To get better
performance, larger PFI credit can be assigned to PND. Otherwise if
cdclk/czclk<1, the default PFI credit of 8 should be set.
v2:
- Change log to lower log level instead of DRM_ERROR
- Change function name to valleyview_program_pfi_credits
- Move program PFI credits to modeset_init instead of intel_set_mode
- Change magic numbers to logical constants
[vsyrjala v3:
- only program in response to cdclk update
- program the credits also when cdclk<czclk
- add CHV bits
v4:
- Change CHV cdclk<czclk credits to 12 (Vijay)]
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Assuming the PND deadline mechanism works reasonably we should do
memory requests as early as possible so that PND has schedule the
requests more intelligently. Currently we're still calculating
the watermarks as if VLV/CHV are identical to g4x, which isn't
the case.
The current code also seems to calculate insufficient watermarks
and hence we're seeing some underruns, especially on high resolution
displays.
To fix it just rip out the current code and replace is with something
that tries to utilize PND as efficiently as possible.
We now calculate the WM watermark to trigger when the FIFO still has
256us worth of data. 256us is the maximum deadline value supoorted by
PND, so issuing memory requests earlier would mean we probably couldn't
utilize the full FIFO as PND would attempt to return the data at
least in at least 256us. We also clamp the watermark to at least 8
cachelines as that's the magic watermark that enabling trickle feed
would also impose. I'm assuming it matches some burst size.
In theory we could just enable trickle feed and ignore the WM values,
except trickle feed doesn't work with max fifo mode anyway, so we'd
still need to calculate the SR watermarks. It seems cleaner to just
disable trickle feed and calculate all watermarks the same way. Also
trickle feed wouldn't account for the 256us max deadline value, thoguh
that may be a moot point in non-max fifo mode sicne the FIFOs are fairly
small.
On VLV max fifo mode can be used with either primary or sprite planes.
So the code now also checks all the planes (apart from the cursor)
when calculating the SR plane watermark.
We don't have to worry about the WM1 watermarks since we're using the
PND deadline scheme which means the hardware ignores WM1 values.
v2: Use plane->state->fb instead of plane->fb
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch implements latest PHY changes in Gain, prop and int co-efficients
based on the vco freq.
v2: Split the original changes into multiple smaller patches based on
review by Ville
v3: Addressed Ville's review comments. Fixed the error introduced in v2.
Clear the old bits before we modify those bits as part of RMW.
v4: TDC target cnt is 10 bits and not 8 bits (Ville)
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Initialize lock detect threshold and select coarse threshold for the
case where M2 fraction division is disabled.
v2: Split the changes into multiple smaller patches (Ville)
v3: Clear out the old bits before we modify those bits as RMW (Ville)
v4: Reset coarse threshold when M2 fraction is enabled (Ville)
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2 : Handle M2 frac division for both M2 frac and int cases
v3 : Addressed Ville's review comments. Cleared the old bits for RMW
v4 : Fix feedfwd gain (Ville)
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Collect the currently enabled counts of slice, subslice, and
execution units using the power gate control ack message
registers specific to Cherryview.
Slice/subslice/EU info and hardware status can now be
determined for CHV, so allow the debugfs SSEU status dump
to proceed for CHV devices.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Total EU was already being detected on CHV, so we just add the
additional info parameters. The detection method is changed to
be more robust in the case of subslice fusing - we don't want
to trust the EU fuse bits corresponding to subslices which are
fused-off.
v2: Fixed subslice disable bitmasks and removed unnecessary ?
operation (Ville)
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Poke at the CBR1_VLV register during init_clock_gating to make sure the
PND deadline scheme is used.
The hardware has two modes of operation wrt. watermarks:
1) PND deadline mode:
- memory request deadline is calculated from actual FIFO level * DDL
- WM1 watermark values are unused (AFAIK)
- WM watermark level defines when to start fetching data from memory
(assuming trickle feed is not used)
2) backup mode
- deadline is based on FIFO status, DDL is unused
- FIFO split into three regions with WM and WM1 watermarks, each
part specifying a different FIFO status
We want to use the PND deadline mode, so let's make sure the chicken
bit is in the correct position on init.
Also take the opportunity to refactor the shared code between VLV and
CHV to a shared function.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have similar DSPARB registers as older platforms, just more of
them due to more planes. Add a bit of code to read out the current FIFO
split from the registers. Will be useful later when we improve the WM
calculations.
v2: Add display_mmio_offset to DSPARB
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the DDL precision handling into vlv_compute_drain_latency() so the
callers don't have to duplicate the same code to deal with it.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Kill the silly DRAIN_LATENCY_PRECISION_* defines and just use the raw
number instead.
v2: Move the sprite 32/16 -> 16/8 preision multiplier
change to another patch (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we must yet halve the DDL drain latency from what we're
using currently. This little nugget is not in any spec, but came
down through the grapevine.
This makes the displays a bit more stable. Not quite fully stable but at
least they don't fall over immediately on driver load.
v2: Update high_precision in valleyview_update_sprite_wm() too (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Change 'mutliple' to 'multiple'
Change 'mutlipler' to 'multiplier'
Change 'Haswel' to 'Haswell'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Definition of VLV RR switch bit and corresponding toggling in
set_drrs function.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When one EU is disabled in a particular subslice, we can tune how the
work is spread between subslices to improve EU utilization.
v2: - Use a bitfield to record which subslice(s) has(have) 7 EUs. That
will also make the machinery work if several sublices have 7 EUs.
(Jeff Mcgee)
- Only apply the different hashing algorithm if the slice is
effectively unbalanced by checking there's a single subslice with
7 EUs. (Jeff Mcgee)
v3: Fix typo in comment (Jeff Mcgee)
Issue: VIZ-3845
Cc: Jeff Mcgee <jeff.mcgee@intel.com>
Reviewed-by: Jeff Mcgee <jeff.mcgee@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Gen9 the render power gating can leave slice/subslice/EU in
a partially enabled state. We must make an explicit request for
full SSEU enablement through the Render Power Clock State
register when resuming render work. This register is save/
restored in the logical ring context image for execlist
submission mode. Initialize its value in each LRC image to
request full enablement according to the device SSEU config.
Thanks to Sharma Ankitprasad and Akash Goel for highlighting the
issue and proposing the initial fix on which this patch is based.
v2: Adjusted the names of the power gating support flags to fit
update of an earlier patch.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: "Akash Goel <akash.goel@intel.com>"
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new section to the 'i915_sseu_status' debugfs entry to
report the currently enabled counts of slice, subslice, and
execution units on the device. The count of enabled subslice
per slice represents the most enabled subslice on any one
slice for devices where imbalances may exist. Similarly, the
count of enabled EU per subslice represents the most enabled
EU on any one subslice.
Collect this device status for Skylake by reading the Gen9
power gate control ack message registers. Power gate control
operates on EU in pairs, therefore our reported counts of
enabled EU can be overestimated by one for each pair in which
one EU is fused-off.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read fuse registers to determine the available slice total,
subslice total, subslice per slice, EU total, and EU per subslice
counts of the SKL device. The EU per subslice attribute is more
precisely defined as the maximum EU available on any one subslice,
since available EU counts may vary across subslices due to fusing.
Set flags indicating the SKL device's slice/subslice/EU (SSEU)
power gating capability. Make all values available via debugfs
entry 'i915_sseu_status'.
v2: Several small clean-ups suggested by Damien. Most notably,
used smaller types for the new device info fields to reduce
memory usage and improved the clarity/readability of the
method used to extract attribute values from the fuse
registers.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added new PHY register definitions to control TDC buffer calibration and
digital lock threshold.
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This W/A is put in a gen9 specific function because it may well be
needed on other gen9 platforms.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's also take the opportunity the remove the comment telling it's a
pre-prod W/A, it should be obvious from the stepping test.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment we compare the whole EDRAM_PRESENT/EDRAMCAP register value
to 1 while EDRAM_PRESENT is only bit 0 (the rest may be used to describe
eDRAM capabilities).
To be more future proof, only look at bit 0 to detect eDRAM presence.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This one doesn't have one of these nice cryptic names unfortunately.
v2: Added missing register bitmap
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch implements core logic of SKL display power well.
v2: Addressed Imre's comments
- Added respective DDIs under power well #1 and #2
- Simplified repetitive code in power well programming
v3: Implemented Imre's comments
- Further simplified power well programming
- Made sure that PW 1 is enabled prior to PW 2
v4: Fix minor conflict with the the cherryview support (Damien)
v5: Add the PLL power domain to the always on power well (Damien)
v6: Disable BIOS power well (Imre)
Use power well data for comparison (Imre)
Put the PLL power domain into PW1 as its needed for CDCLK (Satheesh,
Damien)
v7: Addressed Imre's comments
- Lowered the time out to 1ms
- Added parantheses in macro
- Moved debug message and fixed wait_for interval
v8:
- Add a WARN() when swiching on an unknown power well (Imre, done by Damien)
- Whitespace fixes (spaces instead of tabs) (Damien)
v9: (Imre, done by Damien)
- Merge the register definitions with this patch
- Merge the MISC IO power well in this patch
v10: (Imre, done by Damien)
- Define the Misc I/O power domains to be the power well 1 ones as Misc I/O
needs to be enabled with PW1
- Added Transcoder A and VGA domains to PW 2
- Remove the MISC_IO power domains as well in the the always on
domains definition
- Move Misc I/O power well at the top of the power well list so it's turned
on right after PW1.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3,v6,v7)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mainly taking care of some register offsets, otherwise things are similar to
hsw. Also, programming ddi aux to use hardcoded values for psr data select.
v2: introduce EDP_PSR_AUX_BASE macro (Chris)
v3: Moving to HW tracking for SKL+ platforms, so activating source psr during
psr_enabling and then avoiding psr entries and exits for each frontbuffer
updates.
v4: Using SKL DDI AUX regs instead of changing PSR_AUX regs definition (Rodrigo)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Drop the hunks to short-circuit sw tracking: We'd need to
push this down one level, and I don't fully trust the test coverage
yet to do so. So much prefer we pick a whitelist approach for the
cases we know work correctly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable coarse power gating for Gen9. This feature allows render and
media engine to enter RC6 independently. Policies are configured
together with RC6. This feature will only be enabled when RC6 is
enabled.
v2: Rebase after Chris'/Mika's forcewake change (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use new Sideband offset to read max/min/gaur freq based on the SKU it
is running on. Based on the Number of EU, we read different bits to
identify the max frequencies at which system can run.
v2: reuse mask definitions & INTEL_INFO() to get device info (Ville)
v3: add break in switch conditions (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting with Cherryview, devices may have a varying number of EU for
a given ID due to creative fusing. Punit support different frequency for
different fuse data. We use this patch to help get total eu enabled and
read the right offset to get RP0
Based upon a patch from Jeff, but reworked to only store eu_total and
avoid sending info to userspace
v2: Format register definitions (Jani)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Acked-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Found by reading the HIZ_CHICKEN documentation.
Improves performance in a HiZ microbenchmark by around 50%.
Improves performance in OglZBuffer by around 18%.
Thanks to Chris Wilson for helping me figure out where to put this.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
drivers/gpu/drm/i915/intel_runtime_pm.c
Separate branch so that Takashi can also pull just this refactoring
into sound-next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Haswell significantly improved the performance of sampler_c messages,
but the optimization appears to be off by default. Later platforms
remove this bit, and apparently always enable the optimization.
Improves performance in "Counter Strike: Global Offensive" by 18%
at default settings on Iris Pro.
This may break sampling of paletted formats (P8/A8P8/P8A8). It's
unclear whether it affects sampling of paletted formats in general,
or just the sample_c message (which is never used).
While libva does have support for using paletted formats (primarily
for OSDs), that support appears to have been broken for at least a
year, so I couldn't observe a regression from this:
I tried to get libva-intel to use paletted formats, and observe a
regression...but the only thing I found that used it was mplayer's OSD
(on screen display). Even without my patch, the colors were totally
wrong with that, and it's according to a few distro wikis, that's been
the case for over a year.
If libva's code for paletted formats /is/ broken, they could always
add code to disable this bit using the command validator when fixing
it.
Further investigation from Haihao shows that libva mplayer OSD seems
to work at least on his setup (still unclear what's wron with Ken's),
and that it's not affected by this patch. Quoting the discussion
between Haihao and Ken:
> > > If you use "-vo gl" or "-vo xv", the OSD is solid white text with a black
> > > border around it. I presume that it's supposed to be white with vaapi as
> > > well, but I guess I'm not entirely sure.
> > >
> > > It's possible that the optimization doesn't affect the palette as long as
> > > you never use sample_c with the paletted textures.
> >
> > I verified the palette takes effect in the following way:
> >
> > 1. Only support P8A8 format in the driver
> >
> > 2. ran the above command and I saw white OSD text
> >
> > 3. Only support P4A4 format in the driver and don't use
> > 3DSTATE_SAMPLER_PALETTE_LOAD0 to load the value to the texture palette,
> > so the palette keeps unchanged.
> >
> > 4. ran the above command and I saw black OSD text.
> >
> > 5. Load the right value to the texture palette and ran the above command
> > again, I saw white OSD text.
> >
> > Hence I think sample_c with the paletted textures is used in the driver.
>
> That sounds like the palette is actually working, then. Great :)
>
> I doubt that libva would use sample_c - sampling with a shadow comparison?
> It looks like it just uses sample and sample+killpix.
You are right, libva driver doesn't use sample_c message.
> I'm pretty sure the sample_c optimization just uses the palette memory as
> storage for some stuff, so it's quite possible it just works if you're
> only using sample and sample+killpix.
Thanks for the explanation, it makes sense to me.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Add wa name from Ville's review to the comment and copypaste
the explanation why we don't care about libva (already broken) from
Ken. Also add conclusion from libva devs that&why this is all fine.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: "Xiang, Haihao" <haihao.xiang@intel.com>
Cc: libva@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There exists a current workaround to prevent a hang on context switch
should the ring go to sleep in the middle of the restore,
WaProgramMiArbOnOffAroundMiSetContext (applicable to all gen7+). In
spite of disabling arbitration (which prevents the ring from powering
down during the critical section) we were still hitting hangs that had
the hallmarks of the known erratum. That is we are still seeing hangs
"on the last instruction in the context restore". By comparing -nightly
(broken) with requests (working), we were able to deduce that it was the
semaphore LRI cross-talk that reproduced the original failure. The key
was that requests implemented deferred semaphore signalling, and
disabling that, i.e. emitting the semaphore signal to every other ring
after every batch restored the frequent hang. Explicitly disabling PSMI
sleep on the RCS ring was insufficient, all the rings had to be awake to
prevent the hangs. Fortunately, we can reduce the wakelock to the
MI_SET_CONTEXT operation itself, and so should be able to limit the extra
power implications.
Since the MI_ARB_ON_OFF workaround is listed for all gen7 and above
products, we should apply this extra hammer for all of the same
platforms despite so far that we have only been able to reproduce the
hang on certain ivb and hsw models. The last question is whether we want
to always use the extra hammer or only when we know semaphores are in
operation. At the moment, we only use LRI on non-RCS rings for
semaphores, but that may change in the future with the possibility of
reintroducing this bug under subtle conditions.
v2: Make it explicit that the PSMI LRI are an extension to the original
workaround for the other rings.
v3: Bikeshedding variable names and whitespacing
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80660
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83677
Cc: Simon Farnsworth <simon@farnz.org.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Peter Frühberger <fritsch@xbmc.org>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In the gen7 pipe control there is an extra bit to flush the media
caches, so let's set it during cache invalidation flushes.
v2: Rename to MEDIA_STATE_CLEAR to be more inline with spec.
Cc: Simon Farnsworth <simon@farnz.org.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This will allow us to read the number of dispatched compute threads
for GL_ARB_pipeline_statistics_query.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Should probably just init this in the GMbus code all the time, based on
the cdclk and HPLL like we do on newer platforms. Ville has code for
that in a rework branch, but until then we can fix this bug fairly
easily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76301
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Nikolay <mar.kolya@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
To get stable CRCs from the DP CRC source we need to reset the
scrambler for each frame. Enable the reset feature when grabbing
CRCs for pipe C on CHV. Pipes A and B were already covered due
sharing the code with VLV.
We can safely extend PIPE_SCRAMBLE_RESET_MASK to deal with CHV since
the extra bit was MBZ on the older platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Was missing.
Issue: VIZ-4701
Signed-off-by: Michael H. Nguyen <michael.h.nguyen@intel.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was playing with clang and oh surprise! a warning trigerred by
-Wshift-overflow (gcc doesn't have this one):
WA_SET_BIT_MASKED(GEN7_GT_MODE,
GEN6_WIZ_HASHING_MASK | GEN6_WIZ_HASHING_16x4);
drivers/gpu/drm/i915/intel_ringbuffer.c:786:2: warning: signed shift result
(0x28002000000) requires 43 bits to represent, but 'int' only has 32 bits
[-Wshift-overflow]
WA_SET_BIT_MASKED(GEN7_GT_MODE,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/intel_ringbuffer.c:737:15: note: expanded from macro
'WA_SET_BIT_MASKED'
WA_REG(addr, _MASKED_BIT_ENABLE(mask), (mask) & 0xffff)
Turned out GEN6_WIZ_HASHING_MASK was already shifted by 16, and we were
trying to shift it a bit more.
The other thing is that it's not the usual case of setting WA bits here, we
need to have separate mask and value.
To fix this, I've introduced a new _MASKED_FIELD() macro that takes both the
(unshifted) mask and the desired value and the rest of the patch ripples
through from it.
This bug was introduced when reworking the WA emission in:
Commit 7225342ab5
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Tue Oct 7 17:21:26 2014 +0300
drm/i915: Build workaround list in ring initialization
v2: Invert the order of the mask and value arguments (Daniel Vetter)
Rewrite _MASKED_BIT_ENABLE() and _MASKED_BIT_DISABLE() with
_MASKED_FIELD() (Jani Nikula)
Make sure we only evaluate 'a' once in _MASKED_BIT_ENABLE() (Dave Gordon)
Add check to ensure the value is within the mask boundaries (Chris Wilson)
v3: Ensure the the value and mask are 16 bits (Dave Gordon)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
For dual link MIPI Panels, each port needs half of pixel clock. Pixel overlap
can be enabled if needed by panel, then in that case, pixel clock will be
increased for extra pixels.
v2 : Address review comments by Jani
- Removed the bit mask used for ->dual_link
- Used DSI instead of MIPI for #define variables
v3: Added the VLV_DISPLAY_BASE to VLV_CHICKEN_3 register
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Dual Link MIPI Panels, both Port A and Port C should be enabled
during the MIPI encoder enabling sequence. Similarly, during the
disabling sequence, both ports needs to be disabled.
v2: Used for_each_dsi_port macro instead of for loop
v3: Used intel_dsi->ports instead of dual_link var for dual link configuration check
v4: Masking of the required MIPI port bits before writing proper values
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MI_STORE_DWORD_IMM length has been the same ever since gen4. Rename
the define to avoid potential confusion if someone tries to use this
on pre-gen8.
Also correct the comment on MI_MEM_VIRTUAL bit. It's present on 945,g33
and 965 only.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add USE_GGTT define for g4x+ too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MIPI DSI works on ports A and C, which map to pipes A and B,
respectively. Things are going to get more complicated with the
introduction of dual link DSI support, so clean up the register defines
and code to match reality.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Baytrail (Valleyview) and Braswell (Cherryview) uses a complete different
implementation of PSR that we currently have supported for
Haswell and Broadwell. So let's start by adding registers definitions.
I usually don't like commit that adds just registers without using,
but after I put all in one commit I realized that no one would want
to take the AR to review it so I decided to split in order to make
reviewer's life easier. Only last commit in this series will actually
enable the PSR on intel enable panel path.
But as it happens currently with HSW/BDW the plan is to let it
disabled by default (protected by kernel parameter)
while we are able to fully validate it.
v2: Remove a unused bit definition that isn't used on vlv and
reserved on chv as pointed out by Durgadoss.
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
915/945 have the same reset registers as 965, so share the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ctg the reset bit directly controls the reset signal. We must
assert it for >=20usec and then deassert it. Bit 1 is a RO status bit
which should also go down when the reset is no longer asserted.
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's just throw in the towel on this one and take the cheap way out.
Based on a patch from Chris Wilson, but checking for a different bit.
Chris' patch checked for even bank layout, this one here for a magic
bit. Given the evidence we've gathered (not much) both work I think,
but checking for the magic bit might be more accurate.
Anyway, works on my gm45 here.
For paranoi restrict to gen4 (and mobile), since we've only ever seen
this on gm45 and i965gm.
Also add some debugfs output so that we can skip the tiled swapping
tests properly in these cases.
v2: Clean up the quirk'ed pin count in free_object to avoid upsetting
the WARN_ON. Spotted by Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28813
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45092
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added gen6_init_rps_frequencies() to initialize
the rps frequency values. This function replaces
parse_rp_state_cap(). In addition to reading RPn,
RP0, and RP1 from RP_STATE_CAP register, the new
function reads efficient frequency (aka RPe) from
pcode for Haswell and Broadwell and sets the turbo
softlimits. The turbo minimum frequency softlimit
is set to RPe for Haswell and Broadwell and to RPn
otherwise.
For RPe, the efficiency is based on the frequency/power
ratio (MHz/W); this is considering GT power and not
package power. The efficent frequency is the highest
frequency for which the frequency/power ratio is within
some threshold of the highest frequency/power ratio.
A fixed decrease in frequency results in smaller
decrease in power at frequencies less than RPe than
at frequencies above RPe.
v2: Following suggestions from Chris Wilson and
Daniel Vetter to extend and rename parse_rp_state_cap
and to open-code a poorly named function.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Remove unused variables.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits [18:16] of GEN6_GT_THREAD_STATUS_REG have always had the same
meaning since SNB. So treating them as something special for HSW doesn't
make sense to me.
Also the bits *seem* to work exactly the same way on IVB, HSW GT2 and
HSW GT3. At least intel_reg_read gives the identical results on all
platforms with and without forcewake.
Also the HSW PM guide rev 0.99 (ww05 2013) doesn't say anything about
those bits. It just says to poll for bits [2:0]. As does the more recent
BDW PM guide.
So just drop the HSW special case and treat all platforms the same way.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the magic number for the GPLLENABLE bit by adding a name for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville found out that the DATA1 register exists since SNB with some
scarce apparitions in the specs throughout the times. In his own words:
Also according to Bspec the mailbox data1 register already existed
since snb. The hsw cdclk change sequence also mentions that it should
be set to 0, but eg. the bdw IPS sequence doesn't mention it. I guess
in theory some pcode command might cause it to be clobbered, so I'm
thinking we should just explicitly set it to 0 for all platforms in
the pcode read/write functions
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new AUX port irq bits where needed.
v2: Rebase on top of upstream changes
v3: Rebase on top of Oscar change to write IIR as soon as possible (Damien)
v4: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This moved around on SKL, so we need to make sure we read/write the
correct regs.
v2: fixup WIN_POS offsets (Paulo)
zero out WIN_POS reg at disable time (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuougseek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few bits have changed in MI_DISPLAY_FLIP to accomodate the new planes.
DE_RRMR seems to have kept its plane flip bits backward compatible.
v2: Rebase on top of nightly
v3: Rebase on top of nightly (minor conflict in i915_reg.h)
v4: Remove code that is now part of intel_crtc_page_flip()
Don't use BUG() in default:
Use intel_crtc->unpin_work->gtt_offset
(Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Fixup compilation due to the removal of the intel_ddi_dpll_id enum.
And add a fixme about the abuse of pipe_config here.
v3: Rebase on top of the hsw_ddi_clock_get() rename (Damien)
v4: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines the necessary SKL registers for implementing the
new clocking mechanism.
v2: Addressed review comments by Damien
- Added code comment
- Introduced enum for WRPLL values
v3: Rebase on top of nightly (minor conflict in i915_reg.h)
v4: Use 0x, not 0X (Ville)
v5: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3,v4)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The predicate source registers are needed to implement conditional
rendering without stalling. The two source registers are used to load
the previous values of the PS_DEPTH_COUNT register saved from
PIPE_CONTROL commands. These can then be compared and used to set the
predicate enable bit via the MI_PREDICATE command.
The command parser version number is increased to 2 to make it easier
to detect the new functionality in user space.
Signed-off-by: Neil Roberts <neil@linux.intel.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com> (v1)
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next so that I can keep merging patches. Specifically I
want:
- atomic stuff, yay!
- eld parsing patch from Jani.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Implement common forcewake functions shared by Gen9 features.
v2: Make the focewake_{get,put} functions static (Mika)
Small coding style fix in the function definition (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Adapt to the planes/cursor split
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines SKL specific PLANE_WM Watermark registers. It also
defines macros to get the addresses of different LP levels within a pipe.
v2: Reworked the register definitions and associated macros to make it more
generic and be able to use for_each_pipe in values computation.
Incorporated Damien's review comments and indentation.
v3: Added default values for lines and blocks. Provided mask for blocks.
v4: Prefix intermedidate (internal-only) macros with _ (Ville)
v5: Remove the lines and block defaults value (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch reads the memory latency values for all the 8 levels for
SKL. These values are needed for the Watermark computation.
v2: Incorporated the review comments from Damien on register
indentation.
v3: Updated the code to use the sandybridge_pcode_read for reading
memory latencies for GEN9.
v4: Don't put gen 9 in the middle of an ordered list of ifs
(Damien)
v5: take the rps.hw_lock around sandybridge_pcode_read() (Damien)
v6: Use gen >= 9 in the pcode_read() function for data1.
Move the defines near the gen6 ones and prefix them with PCODE.
Remove unused timeout define (the pcode_read() code has a larger
timeout already).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make audio related register defines conform to existing style: Add _MASK
where relevant, indent the defines for register contents, don't indent
the defines for register addresses, prefix pipe specific register
address defines with underscores, drop self explanatory comments.
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just various stuff all over from a bunch of people. Shortlog gives a beter
overview, it's really all misc drm patches.
* tag 'topic/core-stuff-2014-11-05' of git://anongit.freedesktop.org/drm-intel:
drm/edid: add #defines and helpers for ELD
drm/dp: Add counters in the drm_dp_aux struct for I2C NACKs and DEFERs
drm: Remove compiler BUG_ON() test
drm: Fix DRM_FORCE_ON_DIGITAL use
drm/gma500: Don't destroy DRM properties in the driver
drm/i915: Don't destroy DRM properties in the driver
drm: Add a note to drm_property_create() about property lifetime
gpu: drm: Fix warning caused by a parameter description in drm_crtc.c
drm/dp-helper: Move the legacy helpers to gma500
drm/crtc: Remove duplicated ioctl code
drm/crtc: Fix two typos
gpu:drm: Fix typo in Documentation/DocBook/drm.xml
gpu: drm: drm_dp_mst_topology.c: Fix improper use of strncat
drm: drm_err: Remove unnecessary __func__ argument
drm: Implement O_NONBLOCK support on /dev/dri/cardN
CHV has a programmable CSC unit on the pipe B sprites. Program the unit
appropriately for BT.601 limited range YCbCr to full range RGB color
conversion. This matches the programming we currently do for sprites
on the other pipes and on other platforms.
It seems the CSC only works when the input data is YCbCr. For RGB
pixel formats it doesn't matter what we program into the CSC registers.
Doesn't make much sense to me especially since the register names give
the impression that RGB input data would also work. But that's how
it behaves here.
In the review discussions there's been some nice math to explain the
values obtained here. First about the YCbCr->RGB matrix:
"I had the RGB->YCbCr matrix, inverted it and the values came out. But they
should match the wikipedia article. Also keep in mind that the coefficients
are in .12 in fixed point format, hence we need a 1<<12 factor. So let's
try it:
Kb=.114
Kr=.299
(1<<12) * 255/219 ~= 4769
-(1<<12) * 255/112*(1-Kb)*Kb/(1-Kb-Kr) ~= -1605
-(1<<12) * 255/112*(1-Kr)*Kr/(1-Kb-Kr) ~= -3330
(1<<12) * 255/112*(1-Kr) ~= 6537
(1<<12) * 255/112*(1-Kb) ~= 8263
"Looks like the same values to me."
And then about the limits used for clamping:
"> where did you get these min/max?
"The hardware apparently deals in 10bit values, so we need to multiply everything
by 4 when we start with the 8bit min/max values.
Y = [16:235] * 4 = [64:940]
CbCr = ([16:240] - 128) * 4 = [-112:112] * 4 = [-448:448]
"The -128 being the -0.5 bias that the hardware already applied before
the data entered the CSC unit."
Raw data is also supplied in 10bpc in the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Copypaste explanations&math from the review discussion.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV adds a bunch of new registers for primary plane size/position and
pipe blender setup. Initialize all those registers to avoid nasty
surprises. PRIMSIZE is especially important as without programming it
the outout will be garbled whenever the primary plane size would not
match what the BIOS set up.
Also program the sprite constant alpha register to disable the constant
alpha blending factor. This applies to vlv as well as chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor plane also supports 180 degree rotation. Add a new
"cursor-rotation" property on the crtc which controls this.
Unlike sprites, the cursor has a fixed size, so if you have a small
cursor image with the rest of the bo filled by transparent pixels,
simply flipping the rotation property will cause the visible part
of the cursor to shift. This is something to keep in mind when
using cursor rotation.
v2: Fix gen4/vlv by offsetting the base address appropriately
v3: Removing cursor-rotation property and using rotation property on cursor
plane.
v4: Changing the author name back to Ville.
v5 (by Matt Roper): Slight tweaking to apply against latest di-nightly
codebase.
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by (IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Current chv spec teels we can only use either 16 or 32 bits as precision.
Although in the past VLV went from 16/32 to 32/64 and spec might not be updated,
these precision values brings stability and fixes some issues Wayne was facing.
Cc: Wayne Boyer <wayne.boyer@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Wayne Boyer <wayne.boyer@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Sprinkle const as requested by Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I managed to fumble the per spline PCS DW11 register defines in:
commit 570e2a747b
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Aug 18 14:42:46 2014 +0300
drm/i915: Clear TX FIFO reset master override bits on chv
Fortunately the bit in DW0 that was cleared due to this didn't have
any effect as long as the bit we meant to clear was already zero.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fix commit ref as pointed out by Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for 180 degree rotation for primary and sprite planes
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I've sent the first pull request to Dave and I expect his request
for a merge tree any second now ;-)
More seriously I have some pending patches for 3.19 that depend upon
both trees, hence backmerge. Conflicts are all trivial.
Conflicts:
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/intel_display.c
v2: Of course I've forgotten the fixup script for the silent conflict.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This patch fix spelling typos found in drm.xml.
It is because the file is generated from comments in
source codes, I have to fix the typos within source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clear the override bits to make sure the hardware manages
the TX FIFO reset master on its own.
v2: Squash with the earlier attempt at forcing the override bits
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The register can house two different swing marging/deemph settings at
once. However only one gets used based on some other bits. Make sure we
set those bits correctly to make the hardware use the settings we
provided.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use pack_aux() to construct the PSR exit DPMS D0 AUX message,
and use the defines from dp_dp_helper.h to populate the message
contents.
v2: Use sizeof() for message size (Jani)
Use a generic loop to write EDP_PSR_AUX_DATA registers
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell and later silicon has added a new pixel replication register
to the pipe timings for each transcoder. Now in addition to the
DPLL_A_MD register for the pixel clock double, we also need to write
to the TRANS_MULT_n (0x6002c) register to double the pixel data. Writing
to the DPLL only double the pixel clock.
ver2: Macro name change from MULTIPLY to PIPE_MULTI. (Daniel)
ver3: Do not set pixel multiplier if transcoder is eDP (Ville)
ver4: Macro name change to PIPE_MULT and default else pixel_multiplier
Cc: Ville =?iso-8859-1?Q?Syrj=E4l=E4?= <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Appease checkpatch and move one hunk back into the right
place that git am misplace!?]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL stage 1 patches still need polish so will likely miss the 3.18
merge window. We've decided to postpone to 3.19 so let's pull this in
to make patch merging and conflict handling easier.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This reverts commit c76bb61a71.
It's apparently too broken so that Rodrigo submitted a patch to add a
config option for it. Given that the design is also ... suboptimal and
that I've only merged this to get lead engineers and managers off my
back for one second let's just revert this.
/me puts on combat gear again
It was worth a shot ...
References: http://mid.mail-archive.com/1411686380-1953-1-git-send-email-rodrigo.vivi@intel.com
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Daisy Sun <daisy.sun@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
SKL Uses the same hardware for all planes now, so called "universal"
planes. Ie both the primary planes and sprite planes share the same
logic. This patch implements the drm_plane vfuncs for "sprites" ie
planes that aren't the primary plane.
v2: Couple of fixes:
- Actually enabled the planes and fix the plane number
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To accomodate the extra planes, the bit definitions were shuffled around
a bit.
v2: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
v3: Rebase after yet another change int that area (done with wiggle)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
