If a GPIO driver uses gpiochip_add_pin_range() (which is usually the
case for GPIO/PFC combos), the GPIO hogging mechanism configured from DT
doesn't work:
requesting hog GPIO led1-high (chip r8a73a4_pfc, offset 28) failed
The actual error code is -517 == -EPROBE_DEFER.
The problem is that PFC+GPIO registration is handled in multiple steps:
1. pinctrl_register(),
2. gpiochip_add(),
3. gpiochip_add_pin_range().
Configuration of the hogs is handled in gpiochip_add():
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_hogs
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
pinctrl_request_gpio
pinctrl_get_device_gpio_range
However, at this point the GPIO controller hasn't been added to
pinctrldev_list yet, so the range can't be found, and the operation fails
with -EPROBE_DEFER.
To fix this, add a "gpio-ranges" property to the gpio device node, so
the ranges are added by of_gpiochip_add_pin_range(), which is called by
of_gpiochip_add() before the call to of_gpiochip_scan_hogs().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the MMCIF device node (the board has
eMMC chip) along with the necessary voltage regulator (note that the Vcc/Vccq
regulator is dummy -- it's required by the MMCIF driver but doesn't actually
exist on the board).
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7794 part of the MMCIF0 device node.
Based on the orginal patch by Shinobu Uehara <shinobu.uehara.xc@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7794 SoC based SILK low cost board.
SCIF2 serial port support is included, so that the serial console can work.
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7794 part of the PFC device node.
Based on original patch by Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch contains device tree node definition for JPEG codec peripheral
found in the Renesas R-Car r8a7791 SoC.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch contains device tree node definition for JPEG codec peripheral
found in the Renesas R-Car r8a7790 SoC.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The adv7511 IRQ is low level triggered, not falling edge triggered. The
wrong sense configuration results in no interrupt being triggered at
all, breaking hotplug detection. Fix it.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It is easy to modify settings for Test or other purpose if sound has label
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It is easy to modify settings for Test or other purpose if sound has label
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the r8a7779 SoC DTS and the Marzen Reference
C board code to use DTS only for INTC-IRQPIN IRLM setup.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the R-Car Gen2 GIC is assumed to be a GIC-400.
This has been confirmed by reading the GICD_IIDR register (on r8a7791),
which reports 0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the R-Car Gen2 GIC is assumed to be a GIC-400.
This has been confirmed by reading the GICD_IIDR register (on r8a7791),
which reports 0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the R-Car Gen2 GIC is assumed to be a GIC-400.
This has been confirmed by reading the GICD_IIDR register, which reports
0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the R-Car Gen2 GIC is assumed to be a GIC-400.
This has been confirmed by reading the GICD_IIDR register (on r8a7791),
which reports 0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the documentation states it's a GIC-400.
This has been confirmed by reading the GICD_IIDR register, which reports
0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Configure pinctrl and a GPIO-controller board mux for LCD use.
This allows the armadillo800eva board staging code to enable lcdc0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7790 part of the EtherAVB device node.
Based on original patch by Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the EtherAVB clock to the R8A7790 device tree.
Based on original patch by Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Minimal DT description and Makefile entry for the Gose eval board.
Support for console, timer, and Ethernet.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Minimal r8a7793 device tree including one CPU core, interrupt controllers,
timers, two serial ports, and the Ethernet controller, plus the required
clock descriptions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
A new intel_pmc_ipc driver, a symmetrical allocation and free fix in
dell-laptop, a couple minor fixes, and some updated documentation in the
dell-laptop comments.
intel_pmc_ipc:
- Add Intel Apollo Lake PMC IPC driver
tc1100-wmi:
- Delete an unnecessary check before the function call "kfree"
dell-laptop:
- Fix allocating & freeing SMI buffer page
- Show info about WiGig and UWB in debugfs
- Update information about wireless control
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVmM8aAAoJEKbMaAwKp364iUkH/jihOduWkDTzzzxRP2Dv2nEh
qyvE94Nc9A9dl87C2+II/Pi1s8h4CJOQpl70syYYPc4FdF70hpvP8TbHkgCWrY/d
F8CoS9L9keviMtGOWlbEL9hBjfSDNwTMESTrDxrwhA04TSAwjDmXhhiUOF5FjFJm
CX5+ZQ3iXEH6KsENR+Er54J9+6WKE6IuRcnnKCapnPQ8cEYeVn+WEPyzHCOy8Pg3
xzzUar3/knS2VMIb5eIVpaKFvD9P9qBsC/gQ0pk1Y+686gwQZMVURDv8lw8hfXpx
TJDOXk21P8WbSH1r+jwax5wLjLge7vJtYG2Deye6MUgvSgg+O2tSVCv9SMQR088=
=WUgr
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.2-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull late x86 platform driver updates from Darren Hart:
"The following came in a bit later and I wanted them to bake in next a
few more days before submitting, thus the second pull.
A new intel_pmc_ipc driver, a symmetrical allocation and free fix in
dell-laptop, a couple minor fixes, and some updated documentation in
the dell-laptop comments.
intel_pmc_ipc:
- Add Intel Apollo Lake PMC IPC driver
tc1100-wmi:
- Delete an unnecessary check before the function call "kfree"
dell-laptop:
- Fix allocating & freeing SMI buffer page
- Show info about WiGig and UWB in debugfs
- Update information about wireless control"
* tag 'platform-drivers-x86-v4.2-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
intel_pmc_ipc: Add Intel Apollo Lake PMC IPC driver
tc1100-wmi: Delete an unnecessary check before the function call "kfree"
dell-laptop: Fix allocating & freeing SMI buffer page
dell-laptop: Show info about WiGig and UWB in debugfs
dell-laptop: Update information about wireless control
Pull more vfs updates from Al Viro:
"Assorted VFS fixes and related cleanups (IMO the most interesting in
that part are f_path-related things and Eric's descriptor-related
stuff). UFS regression fixes (it got broken last cycle). 9P fixes.
fs-cache series, DAX patches, Jan's file_remove_suid() work"
[ I'd say this is much more than "fixes and related cleanups". The
file_table locking rule change by Eric Dumazet is a rather big and
fundamental update even if the patch isn't huge. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (49 commits)
9p: cope with bogus responses from server in p9_client_{read,write}
p9_client_write(): avoid double p9_free_req()
9p: forgetting to cancel request on interrupted zero-copy RPC
dax: bdev_direct_access() may sleep
block: Add support for DAX reads/writes to block devices
dax: Use copy_from_iter_nocache
dax: Add block size note to documentation
fs/file.c: __fget() and dup2() atomicity rules
fs/file.c: don't acquire files->file_lock in fd_install()
fs:super:get_anon_bdev: fix race condition could cause dev exceed its upper limitation
vfs: avoid creation of inode number 0 in get_next_ino
namei: make set_root_rcu() return void
make simple_positive() public
ufs: use dir_pages instead of ufs_dir_pages()
pagemap.h: move dir_pages() over there
remove the pointless include of lglock.h
fs: cleanup slight list_entry abuse
xfs: Correctly lock inode when removing suid and file capabilities
fs: Call security_ops->inode_killpriv on truncate
fs: Provide function telling whether file_remove_privs() will do anything
...
Commit 835a6a2f86 ("Bluetooth: Stop sabotaging list poisoning")
thought that the code was sabotaging the list poisoning when NULL'ing
out the list pointers and removed it.
But what was going on was that the bluetooth code was using NULL
pointers for the list as a way to mark it empty, and that commit just
broke it (and replaced the test with NULL with a "list_empty()" test on
a uninitialized list instead, breaking things even further).
So fix it all up to use the regular and real list_empty() handling
(which does not use NULL, but a pointer to itself), also making sure to
initialize the list properly (the previous NULL case was initialized
implicitly by the session being allocated with kzalloc())
This is a combination of patches by Marcel Holtmann and Tedd Ho-Jeong
An.
[ I would normally expect to get this through the bt tree, but I'm going
to release -rc1, so I'm just committing this directly - Linus ]
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Original-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Original-by: Marcel Holtmann <marcel@holtmann.org>:
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull SCSI target updates from Nicholas Bellinger:
"It's been a busy development cycle for target-core in a number of
different areas.
The fabric API usage for se_node_acl allocation is now within
target-core code, dropping the external API callers for all fabric
drivers tree-wide.
There is a new conversion to RCU hlists for se_node_acl and
se_portal_group LUN mappings, that turns fast-past LUN lookup into a
completely lockless code-path. It also removes the original
hard-coded limitation of 256 LUNs per fabric endpoint.
The configfs attributes for backends can now be shared between core
and driver code, allowing existing drivers to use common code while
still allowing flexibility for new backend provided attributes.
The highlights include:
- Merge sbc_verify_dif_* into common code (sagi)
- Remove iscsi-target support for obsolete IFMarker/OFMarker
(Christophe Vu-Brugier)
- Add bidi support in target/user backend (ilias + vangelis + agover)
- Move se_node_acl allocation into target-core code (hch)
- Add crc_t10dif_update common helper (akinobu + mkp)
- Handle target-core odd SGL mapping for data transfer memory
(akinobu)
- Move transport ID handling into target-core (hch)
- Move task tag into struct se_cmd + support 64-bit tags (bart)
- Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
paulmck)
- Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
paulmck)
- Simplify target backend driver registration (hch)
- Consolidate + simplify target backend attribute implementations
(hch + nab)
- Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
- Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
- Drop unnecessary core_tpg_register TFO parameter (nab)
- Use 64-bit LUNs tree-wide (hannes)
- Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
target: Bump core version to v5.0
target: remove target_core_configfs.h
target: remove unused TARGET_CORE_CONFIG_ROOT define
target: consolidate version defines
target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
target: simplify UNMAP handling
target: replace se_cmd->execute_rw with a protocol_data field
target/user: Fix inconsistent kmap_atomic/kunmap_atomic
target: Send UA when changing LUN inventory
target: Send UA upon LUN RESET tmr completion
target: Send UA on ALUA target port group change
target: Convert se_lun->lun_deve_lock to normal spinlock
target: use 'se_dev_entry' when allocating UAs
target: Remove 'ua_nacl' pointer from se_ua structure
target_core_alua: Correct UA handling when switching states
xen-scsiback: Fix compile warning for 64-bit LUN
target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
target: use 64-bit LUNs
target: Drop duplicate + unused se_dev_check_wce
target: Drop unnecessary core_tpg_register TFO parameter
...
An abstraction layer was added to allow the hardware and clients to be
easily added. This required rewriting the NTB transport layer for this
abstraction layer. This modification will allow future
"high performance" NTB clients.
In addition to this change, a number of performance modifications were
added. These changes include NUMA enablement, using CPU memcpy instead
of asyncdma, and modification of NTB layer MTU size.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CyfQ
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.2' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"This includes a pretty significant reworking of the NTB core code, but
has already produced some significant performance improvements.
An abstraction layer was added to allow the hardware and clients to be
easily added. This required rewriting the NTB transport layer for
this abstraction layer. This modification will allow future "high
performance" NTB clients.
In addition to this change, a number of performance modifications were
added. These changes include NUMA enablement, using CPU memcpy
instead of asyncdma, and modification of NTB layer MTU size"
* tag 'ntb-4.2' of git://github.com/jonmason/ntb: (22 commits)
NTB: Add split BAR output for debugfs stats
NTB: Change WARN_ON_ONCE to pr_warn_once on unsafe
NTB: Print driver name and version in module init
NTB: Increase transport MTU to 64k from 16k
NTB: Rename Intel code names to platform names
NTB: Default to CPU memcpy for performance
NTB: Improve performance with write combining
NTB: Use NUMA memory in Intel driver
NTB: Use NUMA memory and DMA chan in transport
NTB: Rate limit ntb_qp_link_work
NTB: Add tool test client
NTB: Add ping pong test client
NTB: Add parameters for Intel SNB B2B addresses
NTB: Reset transport QP link stats on down
NTB: Do not advance transport RX on link down
NTB: Differentiate transport link down messages
NTB: Check the device ID to set errata flags
NTB: Enable link for Intel root port mode in probe
NTB: Read peer info from local SPAD in transport
NTB: Split ntb_hw_intel and ntb_transport drivers
...
Braino in "9p: switch p9_client_write() to passing it struct iov_iter *";
if response is impossible to parse and we discard the request, get the
out of the loop right there.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If we'd already sent a request and decide to abort it, we *must*
issue TFLUSH properly and not just blindly reuse the tag, or
we'll get seriously screwed when response eventually arrives
and we confuse it for response to later request that had reused
the same tag.
Cc: stable@vger.kernel.org # v3.2 and later
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The brd driver is the only in-tree driver that may sleep currently.
After some discussion on linux-fsdevel, we decided that any driver
may choose to sleep in its ->direct_access method. To ensure that all
callers of bdev_direct_access() are prepared for this, add a call
to might_sleep().
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If a block device supports the ->direct_access methods, bypass the normal
DIO path and use DAX to go straight to memcpy() instead of allocating
a DIO and a BIO.
Includes support for the DIO_SKIP_DIO_COUNT flag in DAX, as is done in
do_blockdev_direct_IO().
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When userspace does a write, there's no need for the written data to
pollute the CPU cache. This matches the original XIP code.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For block devices which are small enough, mkfs will default to creating
a filesystem with block sizes smaller than page size.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
that could have been waited for -rc2. Sending them now since I
was taking care of Peter's patch anyway.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVmB5pAAoJEL/70l94x66DpLAH/A0p2HICsG5Qw3gnI3NxAmK4
YUvtMx0d67mFXPg0kuYRMO7C2Is6XHKtnmsX8oqkg3JTRFfn7XYqlwvrrK3Be08U
tGvhigneJTGDXwU74jyik+D6VLmyJP3CxEvXM3d9AFyy7Ro9Grxx0Ja8c9cmKGQE
esCwNAEJOcqaQMtNIix3WtXifOVFr40NZlbAawsMyxVw8LZK/K5maXyUTRDI57Qn
B1wbTN1KD847/0rLrit+8VlsGEZBorUgCFhueeYGy/7EdiY0bNkzhLWb4erlWnRq
ZlKzsLdfXmEg2CEepaHCm5jlLfIurgbLfoV1tzQ5jAuj/SHmUxq+k3lZZYTYA3w=
=vDKM
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Except for the preempt notifiers fix, these are all small bugfixes
that could have been waited for -rc2. Sending them now since I was
taking care of Peter's patch anyway"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: add hyper-v crash msrs values
KVM: x86: remove data variable from kvm_get_msr_common
KVM: s390: virtio-ccw: don't overwrite config space values
KVM: x86: keep track of LVT0 changes under APICv
KVM: x86: properly restore LVT0
KVM: x86: make vapics_in_nmi_mode atomic
sched, preempt_notifier: separate notifier registration from static_key inc/dec
When split BAR is enabled, the driver needs to dump out the split BAR
registers rather than the original 64bit BAR registers.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The unsafe doorbell and scratchpad access should display reason when
WARN is called. Otherwise we get a stack dump without any explanation.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Printouts driver name and version to indicate what is being loaded.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Benchmarking showed a significant performance increase with the MTU size
to 64k instead of 16k. Change the driver default to 64k.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Instead of using the platform code names, use the correct platform names
to identify the respective Intel NTB hardware.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Disable DMA usage by default, since the CPU provides much better
performance with write combining. Provide a module parameter to enable
DMA usage when offloading the memcpy is preferred.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Changing the memory window BAR mappings to write combining significantly
boosts the performance. We will also use memcpy that uses non-temporal
store, which showed performance improvement when doing non-cached
memcpys.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
