The BCM4330 is a 802.11 a/b/g/n WiFi + Bluetooth 4.0 chip from Broadcom.
It is found in the Ampak AP6330 WiFi+BT module. The partiular one I have
identifies as BCM4330B1 for Bluetooth and BCM4330/4 for WiFi.
It is unclear if the AP6330 module uses this revision of the BCM4330, or
if there are multiple revisions. The module does not have revision
markings. This patch elects to use just BCM4330 for the compatible
string.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM20702A1 is a Bluetooth 4.0 chip from Broadcom. It is found in the
Ampak AP6210 WiFi+BT module, identified from the read verbose config info
command response. However the Bluetooth firmware provided by vendors uses
the name BCM20710. This patch elects to use the chip ID returned by the
chip for the compatible string.
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO.
The former provides overall power for the chip, while the latter powers
the I/O pins and buffers.
This patch adds properties for the two so we can describe the power
supply relationships.
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth controllers can take up to two external clocks:
an external frequency reference, substituting the main crystal, and a
LPO clock at 32.768 kHz substituting the internal LPO clock.
In particular, the external LPO clock must be used when the controller
does not have NVRAM connected, and the main reference frequency is not
the default 20 MHz. This is described in detail in the datasheet.
The original "extclk" clock name is ambiguous as to which of these it
refers to, and some designs might even require both.
This patch deprecates the existing name, and adds "txco" and "lpo".
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The commit adds the device tree binding documentation for the MediaTek DWMAC
found on MediaTek MT2712.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add optional reset GPIO, as such a signal is available on the KSZ switches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Introduce protected-clock DT binding to fix breakage on qcom sdm845-mtp
boards where the qspi clks introduced this merge window cause the
firmware on those boards to take down the system if we try to read
the clk registers
- Fix a couple off-by-one errors found by Dan Carpenter
- Handle failure in zynq fixed factor clk driver to avoid using
uninitialized data
-----BEGIN PGP SIGNATURE-----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=t1kp
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few clk driver fixes this time:
- Introduce protected-clock DT binding to fix breakage on qcom
sdm845-mtp boards where the qspi clks introduced this merge window
cause the firmware on those boards to take down the system if we
try to read the clk registers
- Fix a couple off-by-one errors found by Dan Carpenter
- Handle failure in zynq fixed factor clk driver to avoid using
uninitialized data"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: zynqmp: Off by one in zynqmp_is_valid_clock()
clk: mmp: Off by one in mmp_clk_add()
clk: mvebu: Off by one bugs in cp110_of_clk_get()
arm64: dts: qcom: sdm845-mtp: Mark protected gcc clocks
clk: qcom: Support 'protected-clocks' property
dt-bindings: clk: Introduce 'protected-clocks' property
clk: zynqmp: handle fixed factor param query error
Documentation/networking/ is full of cryptically named files with
driver documentation. This makes finding interesting information
at a glance really hard. Move all those files into a directory
called device_drivers (since not all drivers are for device) and
fix up references.
RFC v0.1 -> RFC v1:
- also add .txt suffix to the files which are missing it (Quentin)
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Henrik Austad <henrik@austad.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input updates from Dmitry Torokhov:
"Mostly new IDs for Elan/Synaptics touchpads, plus a few small fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: omap-keypad - fix keyboard debounce configuration
Input: xpad - quirk all PDP Xbox One gamepads
Input: synaptics - enable SMBus for HP 15-ay000
Input: synaptics - add PNP ID for ThinkPad P50 to SMBus
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARR
Input: elan_i2c - add support for ELAN0621 touchpad
Input: hyper-v - fix wakeup from suspend-to-idle
Input: atkbd - clean up indentation issue
Input: st1232 - convert to SPDX identifiers
Input: migor_ts - convert to SPDX identifiers
Input: dt-bindings - fix a typo in file input-reset.txt
Input: cros_ec_keyb - fix button/switch capability reports
Input: elan_i2c - add ELAN0620 to the ACPI table
Input: matrix_keypad - check for errors from of_get_named_gpio()
-----BEGIN PGP SIGNATURE-----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=44JZ
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- Revert a dt-bindings patch whose driver didn't make for 4.20
- fix a kernel oops at vicodec driver
- fix a frame overflow at gspca with was causing regressions on some
cameras, making them to not work
- use the proper type for wait_queue head
- make media request API compatible with 32-bit userspace on 64-bit
kernel
- fix a regression on Kernel 4.19 at dvb-pll
- don't use SPDX headers yet for GFDL
* tag 'media/v4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: mediactl docs: Fix licensing message
media: dvb-pll: don't re-validate tuner frequencies
media: dvb-pll: fix tuner frequency ranges
media: Revert "media: dt-bindings: Document the Rockchip VPU bindings"
media: gspca: fix frame overflow error
media: vicodec: fix memchr() kernel oops
media: cedrus: add action item to the TODO
media: media-request: Add compat ioctl
media: Use wait_queue_head_t for media_request
Here are some small USB and PHY driver fixes for 4.20-rc5
Nothing big at all, just the usual handful of USB fixes for reported
issues, along with some gadget and PHY driver bug fixes.
All of these have been in linux-next with no reported issues.
Note, the USB gadget fixes were in linux-next on its own branch, not in
mine, it just got merged into here yesterday and missed linux-next of
today.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAFfLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn4OwCg1rMrW+r4+OeehFi2wR7wxxP0f1QAnRj/djtD
w3+dT6m3PanQE40d1zi5
=HsrT
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY driver fixes from Greg KH:
"Here are some small USB and PHY driver fixes for 4.20-rc5
Nothing big at all, just the usual handful of USB fixes for reported
issues, along with some gadget and PHY driver bug fixes.
All of these have been in linux-next with no reported issues. Note,
the USB gadget fixes were in linux-next on its own branch, not in
mine, it just got merged into here yesterday and missed linux-next of
today"
* tag 'usb-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: u_ether: fix unsafe list iteration
USB: omap_udc: fix rejection of out transfers when DMA is used
USB: omap_udc: fix USB gadget functionality on Palm Tungsten E
USB: omap_udc: fix omap_udc_start() on 15xx machines
USB: omap_udc: fix crashes on probe error and module removal
USB: omap_udc: use devm_request_irq()
usb: core: quirks: add RESET_RESUME quirk for Cherry G230 Stream series
USB: usb-storage: Add new IDs to ums-realtek
Revert "usb: dwc3: gadget: skip Set/Clear Halt when invalid"
phy: qcom-qusb2: Fix HSTX_TRIM tuning with fused value for SDM845
phy: qcom-qusb2: Use HSTX_TRIM fused value as is
dt-bindings: phy-qcom-qmp: Fix several mistakes from prior commits
phy: uniphier-pcie: Depend on HAS_IOMEM
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEENrCndlB/VnAEWuH5k9IU1zQoZfEFAlv+uhcTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCT0hTXNChl8Q67B/4k/6WVMEssFStSEpC9asrqQs0Itra3
+eIiXrzGfpzO/Gg1O4LV2xUt7JzgLgRa8BBPH8wk+Q/QMOYZsP0qkocb2SWI+J31
JfJGa50l+Beyj8UdeLqZRt62cKCQIBXRaZ4O12ugGYNeQotFsSg4bFa1Gk9aW8Ke
YZT2zYTgD1yaQpBnUcbwnzJEf58vVjgH8zocpm40hlqsUKOJeHoAqUfyfj5RPioX
w9HAc/nDmsHAt32O650poJ851RK2dMNDTSKtUxKTH+nPI7HzdB5HXvlPFpHAf2SC
BrPYUJIOJGPLzhfTRTwAFCfM5C8/y/FtR0GD9vEctVDjSIrcH72aOnre
=NA7B
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.21-20181128' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
This is a pull request for net-next/master consisting of 18 patches.
The first patch is by Colin Ian King and fixes the spelling in the ucan
driver.
The next three patches target the xilinx driver. YueHaibing's patch
fixes the return type of ndo_start_xmit function. Two patches by
Shubhrajyoti Datta add support for the CAN FD 2.0 controllers.
Flavio Suligoi's patch for the sja1000 driver add support for the ASEM
CAN raw hardware.
Wolfram Sang's and Kuninori Morimoto's patches switch the rcar driver to
use SPDX license identifiers.
The remaining 111 patches improve the flexcan driver. Pankaj Bansal's
patch enables the driver in Kconfig on all architectures with IOMEM
support. The next four patches by me fix indention, add missing
parentheses and comments. Aisheng Dong's patches add self wake support
and document it in the DT bindings. The remaining patches by Pankaj
Bansal first fix the loopback support and prepare the driver for the
CAN-FD support needed for the LX2160A SoC. The actual CAN-FD support
will be added in a later patch series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
A few driver specific fixes here, nothing big or that stands out for
anyone other than the driver users.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlv+uFQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GN/B/9rkzlaRTNvBepsN3qbDfFotIt2+9T0
as4tDY5t+C6PWHkKaqezTuKzin+fSOpSQ9n8rx2yc9oddwpelDsqLVxUlxRuN+RB
C+UBfls7rP3J8AlYaGFor+N+MjiRuWVpfYW0PbFf1kM8l1fmOP7FC7BB76G1Ketu
3U9DSWeL5YMZq+IIXI3e77f3luq4/bo2DVxNMQ/PL/frbpRIqOVYag5kGFRxYYez
7rcAo68mOCv/85xdqNZ5u2m+xO/fpSYV+CGFXbYvGPizFIGl9REnw+8DE7EVSCo7
xsPsMuj/bE0Gr3frPguZ0XFsOyFB+SVxqMQxQt2zKiEDuLtQYTFmhs9h
=kDIQ
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here, nothing big or that stands out for
anyone other than the driver users.
The omap2-mcspi fix is for issues that started showing up with a
change in defconfig in this release to make cpuidle get turned on by
default"
* tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: omap2-mcspi: Add missing suspend and resume calls
spi: mediatek: use correct mata->xfer_len when in fifo transfer
spi: uniphier: fix incorrect property items
The FlexCAN controller can parse the stop mode property to enable CAN
self wakeup feature.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add compatible string and new attributes to support the Xilinx CAN
FD 2.0.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
*) Fix updating HSTX_TRIM tuning parameter in qcom-qusb2 PHY driver
*) Fix inconsistencies between dt-bindings and the driver
*) Add "Depend on HAS_IOMEM" uniphier-pcie to avoid randconfig errors
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=wXaJ
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.20-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.20-rc
*) Fix updating HSTX_TRIM tuning parameter in qcom-qusb2 PHY driver
*) Fix inconsistencies between dt-bindings and the driver
*) Add "Depend on HAS_IOMEM" uniphier-pcie to avoid randconfig errors
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-4.20-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: qcom-qusb2: Fix HSTX_TRIM tuning with fused value for SDM845
phy: qcom-qusb2: Use HSTX_TRIM fused value as is
dt-bindings: phy-qcom-qmp: Fix several mistakes from prior commits
phy: uniphier-pcie: Depend on HAS_IOMEM
The correct form is "can be probed", so fix the typo.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e4183d3256.
The commit was picked by mistake, as the Rockchip VPU driver
is not ready for inclusion yet, and it's still under discussion.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a generic clk property for clks which are not intended to be used by
the OS due to security restrictions put in place by firmware. For
example, on some Qualcomm firmwares reading or writing certain clk
registers causes the entire system to reboot, but on other firmwares
reading and writing those same registers is required to make devices
like QSPI work. Rather than adding one-off properties each time a new
set of clks appears to be protected, let's add a generic clk property to
describe any set of clks that shouldn't be touched by the OS. This way
we never need to register the clks or use them in certain firmware
configurations.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pull networking fixes from David Miller:
1) Fix some potentially uninitialized variables and use-after-free in
kvaser_usb can drier, from Jimmy Assarsson.
2) Fix leaks in qed driver, from Denis Bolotin.
3) Socket leak in l2tp, from Xin Long.
4) RSS context allocation fix in bnxt_en from Michael Chan.
5) Fix cxgb4 build errors, from Ganesh Goudar.
6) Route leaks in ipv6 when removing exceptions, from Xin Long.
7) Memory leak in IDR allocation handling of act_pedit, from Davide
Caratti.
8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.
9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
Sabrina Dubroca.
10) When NAPI cached skb is reused, we must set it to the proper initial
state which includes skb->pkt_type. From Eric Dumazet.
11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.
12) Set RX queue properly in various tuntap receive paths, from Matthew
Cover.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tuntap: fix multiqueue rx
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
tipc: don't assume linear buffer when reading ancillary data
tipc: fix lockdep warning when reinitilaizing sockets
net-gro: reset skb->pkt_type in napi_reuse_skb()
tc-testing: tdc.py: Guard against lack of returncode in executed command
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
ip_tunnel: don't force DF when MTU is locked
MAINTAINERS: Add entry for CAKE qdisc
net: bridge: fix vlan stats use-after-free on destruction
socket: do a generic_file_splice_read when proto_ops has no splice_read
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
net/sched: act_pedit: fix memory leak when IDR allocation fails
net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
ipv6: fix a dst leak when removing its exception
net: mvneta: Don't advertise 2.5G modes
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
net/mlx4: Fix UBSAN warning of signed integer overflow
...
The IP101A and IP101G series both have various models. Depending on the
board implementation we need a special property for the IP101GR (32-pin
LQFP package) PHY:
pin 21 ("RXER/INTR_32") outputs the "receive error" signal by default
(LOW means "normal operation", HIGH means that there's either a decoding
error of the received signal or that the PHY is receiving LPI). This pin
can also be switched to INTR32 mode, where the interrupt signal is
routed to this pin. The other PHYs don't need this special handling
because they have more pins available so the interrupt function gets a
dedicated pin.
This adds two properties to either select the "receive error" or
"interrupt" function of pin 21. Not specifying any function means that
the default set by the bootloader is used. This is required because the
IP101GR cannot be differentiated between other IP101 PHYs as the PHY
identification registers on all of these is 0x02430c54.
The IP101G (sold as die only, without package) may suffer from the same
issue depending on how it's integrated into a multi chip package by
another manufacturer. If only the RXER/INTR_32 pin is routed then the
users of the die-only variant may also have to explicitly configure the
mode of hte RXER/INTR_32 pin. This is the reason why no "is-ip101gr"
property was added. I have no evidence though which would confirm this
theory - so the binding itself is independent of that.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IC Plus Corp. has various Ethernet related products such as Ethernet
transceivers, Ethernet controllers, Ethernet switches, etc.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Drop stale DT binding for the arm_big_little_dt driver removed
recently (Sudeep Holla).
- Fix up error handling in the imx6q cpufreq driver to make it
report voltage scaling failures (Anson Huang).
- Fix two issues in the cpufreq documentation (Viresh Kumar,
Zhao Wei Liew).
- Fix ARM cpuidle driver initialization regression from the 4.19
time frame and rework the driver registration part of it to
simplify code (Ulf Hansson).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RD7r
-----END PGP SIGNATURE-----
Merge tag 'pm-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These remove a stale DT entry left behind after recent removal of a
cpufreq driver without users, fix up error handling in the imx6q
cpufreq driver, fix two issues in the cpufreq documentation, and
update the ARM cpufreq driver.
Specifics:
- Drop stale DT binding for the arm_big_little_dt driver removed
recently (Sudeep Holla).
- Fix up error handling in the imx6q cpufreq driver to make it report
voltage scaling failures (Anson Huang).
- Fix two issues in the cpufreq documentation (Viresh Kumar, Zhao Wei
Liew).
- Fix ARM cpuidle driver initialization regression from the 4.19 time
frame and rework the driver registration part of it to simplify
code (Ulf Hansson)"
* tag 'pm-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: cpuidle: Convert to use cpuidle_register|unregister()
ARM: cpuidle: Don't register the driver when back-end init returns -ENXIO
dt-bindings: cpufreq: remove stale arm_big_little_dt entry
Documentation: cpufreq: Correct a typo
cpufreq: imx6q: add return value check for voltage scale
Documentation: cpu-freq: Frequencies aren't always sorted
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEENrCndlB/VnAEWuH5k9IU1zQoZfEFAlvlt0gTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCT0hTXNChl8bMDB/9ElLCS/uh3CznHeX8w24t/LldHoy0q
eposGQ6+uWV/R7lUfNNUtIAcoSxzuOyXSMh9skz8NdExdQ0/9osnvNWemKTGrfhm
ndCVmMd7dMoWX2m1VTJ2jrij3MKPe8HmUei+kB9PrhHFNwofNSOvw2dEVjJDSwUW
gAvs6K/KrHh5ncd9O3JfaXqc9Cs95o0dz4U4AGZ68UjUemx1AmDse2q3JVPQcxn0
muXoWWFXBbKob/0qpFG0xP9ssdq75AL58dlEqRV+64EMgqWcgvdoPxGGIBbP4t0x
zMwE3hCaoC7Uogr28tnQrf4kSm5IC33AiMQDKmBQRtzFLxtCI1wE71M4
=eM20
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.20-20181109' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-11-09
this is a pull request of 20 patches for net/master.
First we have a patch by Oliver Hartkopp which changes the raw socket's
raw_sendmsg() to return an error value if the user tries to send a CANFD
frame to a CAN-2.0 device.
The next two patches are by Jimmy Assarsson and fix potential problems
in the kvaser_usb driver.
YueHaibing's patches for the ucan driver fix a compile time warning and
remove a duplicate include.
Eugeniu Rosca patch adds more binding documentation to the rcar_can
driver bindings. The next two patches are by Fabrizio Castro for the
rcar_can driver and fixes a problem in the driver's probe function and
document the r8a774a1 binding.
Lukas Wunner's patch fixes a recpetion problem in hi311x driver by
switching from edge to level triggered interruts.
The next three patches all target the flexcan driver. Pankaj Bansal's
patch unconditionally unlocks the last mailbox used for RX. Alexander
Stein provides a better workaround for a hardware limitation when
sending RTR frames, by using the last mailbox for TX, resulting in fewer
lost frames. The patch by me simplyfies the driver, by making a runtime
value a compile time constant.
The following 4 patches are by me and provide the groundwork for the
next patches by Oleksij Rempel. To avoid code duplication common code in
the common CAN driver infrastructure is factured out and error handling
is cleaned up.
The next 4 patches are by Oleksij Rempel and fix the problem in the
flexcan driver that other processes see TX frames arrive out of order
with ragards to a RX'ed frame (which are send by a different system on
the CAN bus as the result of our TX frame).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Digging through the "phy-qcom-qmp" showed me many inconsistencies
between the bindings and the reality of the driver. Let's fix them
all.
* In commit 2d66eab183 ("dt-bindings: phy: qmp: Add support for QMP
phy in IPQ8074") we probably should have explicitly listed that
there are no clocks for this PHY and also added the reset names in
alphabetical order. You can see that there are no clocks in the
driver where "clk_list" is NULL.
* In commit 8587b220f0 ("dt-bindings: phy-qcom-qmp: Update bindings
for QMP V3 USB PHY") we probably should have listed the resets for
this new PHY and also removed the "(Optional)" marking for the "cfg"
reset since PHYs that need "cfg" really do need it. It's just that
not all PHYs need it.
* In commit 7f08020741 ("dt-bindings: phy-qcom-qmp: Update bindings
for sdm845") we forgot to update one instance of the string
"qcom,qmp-v3-usb3-phy" to be "qcom,sdm845-qmp-usb3-phy". Let's fix
that. We should also have added "qcom,sdm845-qmp-usb3-uni-phy" to
the clock-names and reset-names lists.
* In commit 99c7c7364b ("dt-bindings: phy-qcom-qmp: Add UFS phy
compatible string for sdm845") we should have added the set of
clocks and resets for "qcom,sdm845-qmp-ufs-phy". These were taken
from the driver.
* Cleanup the wording for what properties child nodes have to make it
more obvious which types of PHYs need clocks and resets. This was
sorta implicit in the "-names" description but I found myself
confused.
* As per the code not all "pcie qmp phys" have resets. Specifically
note that the "has_lane_rst" property in the driver is false for
"ipq8074-qmp-pcie-phy". Thus make it clear exactly which PHYs need
child nodes with resets.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull i2c updates from Wolfram Sang:
"I2C has one bugfix (qcom-geni driver), one arch enablement (i2c-omap
driver, no code change), and a new driver (nvidia-gpu) this time"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
usb: typec: ucsi: add support for Cypress CCGx
i2c: nvidia-gpu: make pm_ops static
i2c: add i2c bus driver for NVIDIA GPU
i2c: qcom-geni: Fix runtime PM mismatch with child devices
MAINTAINERS: Add entry for i2c-omap driver
i2c: omap: Enable for ARCH_K3
dt-bindings: i2c: omap: Add new compatible for AM654 SoCs
AM654 SoCs have same I2C IP as OMAP SoCs. Add new compatible to
handle AM654 SoCs. While at that reformat the existing compatible list
for older SoCs to list one valid compatible per line.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing. Bus state is "active".
Bringing the interface down and back up reconvenes the reception. The
issue is not observed when the hi3110 is the sole device on the SPI bus.
Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.
Unfortunately the hi3110 datasheet is mum on the trigger type. The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Document RZ/G2M (r8a774a1) SoC specific bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Document the support for rcar_can on R8A77965 SoC devices.
Add R8A77965 to the list of SoCs which require the "assigned-clocks" and
"assigned-clock-rates" properties (thanks, Sergei).
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Most of the ARM platforms used v2 OPP bindings to support big-little
configurations. This arm_big_little_dt binding is incomplete and was
never used.
Commit f174e49e49 (cpufreq: remove unused arm_big_little_dt driver)
removed the driver supporting this binding, but the binding was left
unnoticed, so let's get rid of it now.
Fixes: f174e49e49 (cpufreq: remove unused arm_big_little_dt driver)
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix RZ/G2E part number from its description.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull more timer updates from Thomas Gleixner:
"A set of commits for the new C-SKY architecture timers"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings: timer: gx6605s SOC timer
clocksource/drivers/c-sky: Add gx6605s SOC system timer
dt-bindings: timer: C-SKY Multi-processor timer
clocksource/drivers/c-sky: Add C-SKY SMP timer
Dt-bindings doc for gx6605s SOC's system timer.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Dt-bingdings doc for C-SKY SMP system setting.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This series contains a number of improvements to existing drivers, such
as LPSS. Some drivers, such as renesas-tpu and rcar get support for more
SoC generations. To round things off this fixes an issue with the sysfs
interface.
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEEiOrDCAFJzPfAjcif3SOs138+s6EFAlvcT08ZHHRoaWVycnku
cmVkaW5nQGdtYWlsLmNvbQAKCRDdI6zXfz6zoRZ4D/9JewpxTGItNlmgRbrKU2vG
IN5B13z/bEUQo3DS0bsqPqso6kma++Y2JJSs6/qABcjvvigAl9/HTzsP1ooJngmg
3VfEXG6r7q6dA+ckqtIyti/VQ57mLmbSGjp8Y5BfA57hfrbTcKEWSjt5JynJodcR
byOAMazpA+T28Vh4b1ickdztQ92vxe8NrHLHWXzWTePbSuFCeTQ+RjYaKQk3VPsk
kIajkvR2cufxiTY/pBoqJrheNt3W2QY36Lzx8UbVK3vftzFBsBzwepzvO2RAk/D2
lvdGMhOPlDkk8KNaKftbtYct43pAzNfgxjfvRTJP5/+1Sr50FJtQDHYDKEm1qOsn
Z2BZ0rCuAYlu6XITSjYaEfyyrrTpd+Gl7WhSUYnu1Esbv33xD530ALU5MzaU0YD/
yuJCqi5ddojJ2/3uOssDuA3cYdoZnQCzODKWWnH8JjGKas9s8KdbPp+7r9Inb8OX
uVZM4L3k1ZtAyo/JgtwTK+/fog1ulDI1+L3oNgdFNzCS5Kv67AsZyA9SczI8itwn
qdP0ZhQi5ZfmcuadynNy5qAtsZQk9w/i/fij/Rd/PoQOAzRymQJExeVDaDSd50qd
A0jlw3Tw/WDY3YQpnW/555YH4z480smHAvO9tDZFINMD26gy3x+GaFAlUZKLLggp
Oc39LyR4I6Z6rpPHCf1A0Q==
=AECG
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This series contains a number of improvements to existing drivers,
such as LPSS. Some drivers, such as renesas-tpu and rcar get support
for more SoC generations. To round things off this fixes an issue with
the sysfs interface"
* tag 'pwm/for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: lpss: Only set update bit if we are actually changing the settings
pwm: lpss: Force runtime-resume on suspend on Cherry Trail
pwm: Enable TI ECAP driver for ARCH_K3
dt-bindings: pwm: tiecap: Add TI AM654 SoC specific compatible
dt-bindings: pwm: rcar: Add r8a774a1 support
pwm: Send a uevent on the pwmchip device upon channel sysfs (un)export
Revert "pwm: Set class for exported channels in sysfs"
dt-bindings: pwm: renesas-tpu: Document r8a7744 support
dt-bindings: pwm: rcar: Add r8a7744 support
dt-bindings: pwm: renesas: tpu: Document R8A779{7|8}0 bindings
dt-bindings: pwm: renesas: pwm-rcar: Document R8A779{7|8}0 bindings
dt-bindings: pwm: renesas: tpu: Fix "compatible" prop description
pwm: Use SPDX identifier for Renesas drivers
pwm: lpss: Add get_state callback
pwm: lpss: Release runtime-pm reference from the driver's remove callback
pwm: lpss: Check PWM powerstate after resume on Cherry Trail devices
pwm: lpss: Move struct pwm_lpss_chip definition to the header file
pwm: lpss: Add ACPI HID for second PWM controller on Cherry Trail devices
ACPI / PM: Export acpi_device_get_power() for use by modular build drivers
pwm: tegra: Remove gratuituous blank line
-----BEGIN PGP SIGNATURE-----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=5lmL
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Pretty much a normal fixes pull pre-rc1, mostly amdgpu fixes, one i915
link training regression fix, and a couple of minor panel/bridge fixes
and a panel quirk"
* tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm: (37 commits)
drm/amdgpu: revert "enable gfxoff in non-sriov and stutter mode by default"
drm/amd/pp: Print warning if od_sclk/mclk out of range
drm/amd/pp: Fix pp_sclk/mclk_od not work on Vega10
drm/amd/pp: Fix pp_sclk/mclk_od not work on smu7
drm/amd/powerplay: no MGPU fan boost enablement on DPM disabled
drm/amdgpu: Fix skipping hangged job reset during gpu recover.
drm/amd/powerplay: revise Vega20 pptable version check
drm/amd/display: set backlight level limit to 1
drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
drm/bridge: ti-sn65dsi86: Remove the mystery delay
drm/panel: simple: Add "no-hpd" delay for Innolux TV123WAM
drm/panel: simple: Support panels with HPD where HPD isn't connected
dt-bindings: drm/panel: simple: Add no-hpd property
drm/edid: Add 6 bpc quirk for BOE panel.
drm/amdgpu: fix reporting of failed msg sent to SMU (v2)
drm/amdgpu: Fix compute ring 1.0.0 failure after reset
drm/amdgpu: fix VM leaf walking
drm/amdgpu: fix amdgpu_vm_fini
drm/amd/powerplay: commonize the API for retrieving current clocks
...
- Fix cpu node iterator for powerpc systems
- Clarify ARM CPU binding 'capacities-dmips-mhz' property calculations
-----BEGIN PGP SIGNATURE-----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=AG4j
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
- fix cpu node iterator for powerpc systems
- clarify ARM CPU binding 'capacities-dmips-mhz' property calculations
* tag 'devicetree-fixes-for-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: Fix cpu node iterator to not ignore disabled cpu nodes
dt-bindings: arm: Explain capacities-dmips-mhz calculations in example
because of summer time holidays/vacations. The biggest change in the diffstat
is in the Qualcomm clk driver, where they got support for CPUs and handful of
SoCs. After that, the at91 driver got a major rewrite for newer DT bindings
that should make things easier going forward and the TI code moved to a
clockdomain based design. The long tail is mostly small driver updates for
newer clks and some simpler SoC clock drivers such as the Hisilicon and imx
support.
In the core framework, we only have two small changes this time. One is a new
clk API to get all clks for a device with the bulk clk APIs. This allows
drivers that don't care about doing anything besides turning on all the clks to
just clk_get() them all and turn them on. The other change is the beginning of
a way to support save and restore of clk settings in the clk framework. TI is
the only user right now, but we will want to expand upon this design in the
future to support more save and restore of clk registers. At least this gets
us started and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes
-----BEGIN PGP SIGNATURE-----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=V5aK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time it looks like a quieter release cycle in the clk tree. I
guess that's because of summer time holidays/vacations. The biggest
change in the diffstat is in the Qualcomm clk driver, where they got
support for CPUs and handful of SoCs. After that, the at91 driver got
a major rewrite for newer DT bindings that should make things easier
going forward and the TI code moved to a clockdomain based design.
The long tail is mostly small driver updates for newer clks and some
simpler SoC clock drivers such as the Hisilicon and imx support.
In the core framework, we only have two small changes this time.
One is a new clk API to get all clks for a device with the bulk clk
APIs. This allows drivers that don't care about doing anything besides
turning on all the clks to just clk_get() them all and turn them on.
The other change is the beginning of a way to support save and restore
of clk settings in the clk framework. TI is the only user right now,
but we will want to expand upon this design in the future to support
more save and restore of clk registers. At least this gets us started
and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (186 commits)
clk: qcom: Remove unused arrays in SDM845 GCC
clk: fixed-rate: fix of_node_get-put imbalance
clk: s2mps11: Add used attribute to s2mps11_dt_match
clk: qcom: gcc-sdm660: Add MODULE_LICENSE
clk: qcom: Add safe switch hook for krait mux clocks
dt-bindings: clock: Document qcom,krait-cc
clk: qcom: Add Krait clock controller driver
dt-bindings: arm: Document qcom,kpss-gcc
clk: qcom: Add KPSS ACC/GCC driver
clk: qcom: Add support for Krait clocks
clk: qcom: Add IPQ806X's HFPLLs
clk: qcom: Add MSM8960/APQ8064's HFPLLs
dt-bindings: clock: Document qcom,hfpll
clk: qcom: Add HFPLL driver
clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
ARM: Add Krait L2 register accessor functions
clk: imx6q: add mmdc0 ipg clock
clk: imx6sl: add mmdc ipg clocks
clk: imx6sll: add mmdc1 ipg clock
clk: imx6sx: add mmdc1 ipg clock
...
-----BEGIN PGP SIGNATURE-----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=V4X4
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull new experimental media request API from Mauro Carvalho Chehab:
"A new media request API
This API is needed to support device drivers that can dynamically
change their parameters for each new frame. The latest versions of
Google camera and codec HAL depends on such feature.
At this stage, it supports only stateless codecs.
It has been discussed for a long time (at least over the last 3-4
years), and we finally reached to something that seem to work.
This series contain both the API and core changes required to support
it and a new m2m decoder driver (cedrus).
As the current API is still experimental, the only real driver using
it (cedrus) was added at staging[1]. We intend to keep it there for a
while, in order to test the API. Only when we're sure that this API
works for other cases (like encoders), we'll move this driver out of
staging and set the API into a stone.
[1] We added support for the vivid virtual driver (used only for
testing) to it too, as it makes easier to test the API for the ones
that don't have the cedrus hardware"
* tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (53 commits)
media: dt-bindings: Document the Rockchip VPU bindings
media: platform: Add Cedrus VPU decoder driver
media: dt-bindings: media: Document bindings for the Cedrus VPU driver
media: v4l: Add definition for the Sunxi tiled NV12 format
media: v4l: Add definitions for MPEG-2 slice format and metadata
media: videobuf2-core: Rework and rename helper for request buffer count
media: v4l2-ctrls.c: initialize an error return code with zero
media: v4l2-compat-ioctl32.c: add missing documentation for a field
media: media-request: update documentation
media: media-request: EPERM -> EACCES/EBUSY
media: v4l2-ctrls: improve media_request_(un)lock_for_update
media: v4l2-ctrls: use media_request_(un)lock_for_access
media: media-request: add media_request_(un)lock_for_access
media: vb2: set reqbufs/create_bufs capabilities
media: videodev2.h: add new capabilities for buffer types
media: buffer.rst: only set V4L2_BUF_FLAG_REQUEST_FD for QBUF
media: v4l2-ctrls: return -EACCES if request wasn't completed
media: media-request: return -EINVAL for invalid request_fds
media: vivid: add request support
media: vivid: add mc
...
The example contains two values for the capacity currently, 446 in text
and 578 in code. The numbers are all correct but can confuse some of the
readers. This patch tries to explain how the numbers are calculated to
avoid same confusion going forward.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This contains a series of patches that reworks the memory carveout
handling in remoteproc, in order to allow this to be reused for
statically allocated memory regions to be used for e.g. firmware.
It adds support for audio DSP (both TZ-assisted and non-TZ assisted) and
compute DSP on Qualcomm SDM845, TZ-assisted audio DSP, compute DSP and
WiFi processor on Qualcomm QCS404 and through some renaming of the
drivers cleans up the naming situation.
Finally support for custom coreudmp segment handlers is added and
is used in the Qualcomm modem remoteproc driver to gather memory dumps
of the firmware.
-----BEGIN PGP SIGNATURE-----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=mM8w
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.20' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This contains a series of patches that reworks the memory carveout
handling in remoteproc, in order to allow this to be reused for
statically allocated memory regions to be used for e.g. firmware.
It adds support for audio DSP (both TZ-assisted and non-TZ assisted)
and compute DSP on Qualcomm SDM845, TZ-assisted audio DSP, compute DSP
and WiFi processor on Qualcomm QCS404 and through some renaming of the
drivers cleans up the naming situation.
Finally support for custom coreudmp segment handlers is added and is
used in the Qualcomm modem remoteproc driver to gather memory dumps of
the firmware"
* tag 'rproc-v4.20' of git://github.com/andersson/remoteproc: (36 commits)
remoteproc: qcom: q6v5-mss: Register segments/dumpfn for coredump
remoteproc: qcom: q6v5-mss: Add custom dump function for modem
remoteproc: qcom: q6v5-mss: Refactor mba load/unload sequence
remoteproc: Add mechanism for custom dump function assignment
remoteproc: Introduce custom dump function for each remoteproc segment
remoteproc: modify vring allocation to rely on centralized carveout allocator
remoteproc: qcom: q6v5: shore up resource probe handling
remoteproc: qcom: qcom_q6v5_adsp: Fix some return value check
remoteproc: modify rproc_handle_carveout to support pre-registered region
remoteproc: add helper function to check carveout device address
remoteproc: add helper function to allocate rproc_mem_entry from reserved memory
remoteproc: add alloc ops in rproc_mem_entry struct
remoteproc: introduce rproc_find_carveout_by_name function
remoteproc: introduce rproc_add_carveout function
remoteproc: add helper function to allocate and init rproc_mem_entry struct
remoteproc: add name in rproc_mem_entry struct
remoteproc: add release ops in rproc_mem_entry struct
remoteproc: add rproc_va_to_pa function
remoteproc: configure IOMMU only if device address requested
remoteproc: qcom: q6v5-mss: add SCM probe dependency
...
A couple of platforms change hands in the MAINTAINERS file:
- Linus Walleij lists himself for the ARM Reference platforms:
versatile, vexpress, integrator and realview. He has been the main
contributor for these for a while, and makes it official now.
- Vladimir Zapolskiy takes over the LPC18xx platform from Joachim Eastwood
- Manivannan Sadhasivam becomes a secondary maintainer for the
Actions Semi machines
- Nicolas Ferre lists updates the MAINTAINER listing for the AT91
platform: Ludovic Desroches is now a co-maintainer for the platform, and
several other people (Claudiu Beznea, Cristian Birsan, Eugen Hristev,
Codrin Ciubotariu) take over individual device drivers.
Thanks everyone for working on this, and welcome to the new maintainers!
The "virt" platform on qemy or kvm can now be used in big-endian mode
without additional tricks, thanks to Jason Donenfeld.
Once again, we gain support for another NXP i.MX6 variant, this time
it's the i.MX 6ULZ 32-bit single-core version.
On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
and RZ/G2M (r8a774a1). These are described as microcontrollers on the
manufacturer website, but appear to be rather powerful. The RZ/G2M is
used on the reference board for the CIP Super Long Term Support (SLTS)
Linux Kernels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7+46
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"A couple of platforms change hands in the MAINTAINERS file:
- Linus Walleij lists himself for the ARM Reference platforms:
versatile, vexpress, integrator and realview. He has been the main
contributor for these for a while, and makes it official now.
- Vladimir Zapolskiy takes over the LPC18xx platform from Joachim
Eastwood
- Manivannan Sadhasivam becomes a secondary maintainer for the
Actions Semi machines
- Nicolas Ferre lists updates the MAINTAINER listing for the AT91
platform: Ludovic Desroches is now a co-maintainer for the
platform, and several other people (Claudiu Beznea, Cristian
Birsan, Eugen Hristev, Codrin Ciubotariu) take over individual
device drivers.
Thanks everyone for working on this, and welcome to the new
maintainers!
The "virt" platform on qemy or kvm can now be used in big-endian mode
without additional tricks, thanks to Jason Donenfeld.
Once again, we gain support for another NXP i.MX6 variant, this time
it's the i.MX 6ULZ 32-bit single-core version.
On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
and RZ/G2M (r8a774a1). These are described as microcontrollers on the
manufacturer website, but appear to be rather powerful. The RZ/G2M is
used on the reference board for the CIP Super Long Term Support (SLTS)
Linux Kernels"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
MAINTAINERS: Assign myself as a maintainer of ARM/LPC18XX architecture
arm64: exynos: Enable generic power domain support
MAINTAINERS: remove non-exsiting email address of Baoyou
MAINTAINERS: fix pattern in ARM/Synaptics berlin SoC section
MAINTAINERS: Drop dt-bindings/genpd/k2g.h
ARM: samsung: Limit SAMSUNG_PM_CHECK config option to non-Exynos platforms
arm64: actions: Enable PINCTRL in platforms Kconfig
MAINTAINERS: Add entry for Actions Semi Owl SoCs DMA driver
MAINTAINERS: Add entry for Actions Semiconductor Owl I2C driver
MAINTAINERS: Update clock binding entry for Actions Semi Owl SoCs
ARM: imx: add i.mx6ulz msl support
ARM: Assume maintainership of ARM reference designs
ARM: support big-endian for the virt architecture
MAINTAINERS: sdhci: move the Microchip entry to proper location
MAINTAINERS: move former ATMEL entries to proper MICROCHIP location
MAINTAINERS: remove the / ATMEL string from MICROCHIP entries
MAINTAINERS: iio: add co-maintainer to SAMA5D2-compatible ADC driver
MAINTAINERS: pwm: add entry for Microchip pwm driver
MAINTAINERS: dmaengine: add files to Microchip dma entry
MAINTAINERS: USB: change maintainer for Microchip USBA gadget driver
...
