The IGEP AQUILA EXPANSION board is a development platform
for the IGEP COM AQUILA AM335x boards.
The board adds the following connectivity:
o USB OTG
o USB HOST
o HDMI
o Ethernet
o Serial Debug (3.3V)
o 2x46 pin headers
o EEPROM
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP COM AQUILA is industrial processors SODIMM module with
following highlights:
o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor
o Cortex-A8 ARM CPU
o 3.3 volts Inputs / Outputs use industrial
o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
o MicroSD card reader on-board
o Ethernet controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
3.3V fixed regulator does not belong to TPS node - as a result
the fixed regulator is never probed and MMC is continually deferred
due to lack of regulator.
Move the fixed regulator to be at root of platform.
Cc: Joel Fernandes <joelf@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add information about the USB OTG PHY. Without this
the OTG port on beagle will not work.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Provide RESET GPIO and Power regulator for the USB PHY,
the USB Host port mode and the PHY device for the controller.
Also provide pin multiplexer information for USB host pins.
We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Set the alias for ethernet0 and ethernet1 so that uBoot
can set the MAC address appropriately.
Currently u-boot cannot find the alias and there for does
not set the MAC address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add DT nodes for TPS659038 PMIC on DRA7 boards.
It is based on top of:
http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.
Documentation:
- Documentation/devicetree/bindings/mfd/palmas.txt
- Documentation/devicetree/bindings/regulator/palmas-pmic.txt
Boot Tested on DRA7 d1 Board.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix indentation and changelog]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
"gpmc,sync-clki-ps" is not defined/documented, it should be
"gpmc,sync-clk-ps" instead.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefine this on each board DT file.
Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
am33xx boards DTS include the am33xx.dtsi Device Tree
source file that already define a pinmux device node for
the AM33XX SoC Pin Multiplex.
Redefining this for each board makes the Device Tree files
harder to modify and maintain so let's just use what is
already defined in the included .dtsi file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This matches the vendor 3.8.x configuration that is shipping
with the boards.
The LED layout is now:
USR0: heartbeat
USR1: mmc0 (micro-SD slot)
USR2: cpu0
USR3: mmc1 (eMMC)
The cpu0 triggers was put in between the mmc triggers to make
is easier to see where the disk activity is.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The micro-SD slot hooks up all four data pins so lets' use them.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The pinmux is specified in am335x-bone-common.dtsi to be
reused by the eMMC cape.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix traling spaces and useless comments]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This enables the use of MMC cards even when no card was inserted at boot.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Adds AM33XX MMC support for am335x-bone, am335x-evm and am335x-evmsk boards.
Also added is the DMA binding definitions based on the generic DMA request
binding.
Additional changes made to DTS:
* Interrupt, reg and compatible properties added
* ti,needs-special-hs-handling added
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Adds DMA resources to the AM33XX SPI nodes.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Adds AM33XX EDMA support to the am33xx.dtsi as documented in
Documentation/devicetree/bindings/dma/ti-edma.txt
[Joel Fernandes <joelf@ti.com>]
Drop DT entries that are non-hardware-description as discussed in [1]
[1] https://patchwork.kernel.org/patch/2226761/
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This patch makes the Tegra RTC enabled as default for Tegra124 platform.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Pull kbuild fix from Michal Marek:
"Here is an ARM Makefile fix that you even acked. After nobody wanted
to take it, it ended up in the kbuild tree"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
arm, kbuild: make "make install" not depend on vmlinux
Keystone2 based SOCs supports 3 instances of SPI controllers. Add
the device nodes for them.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Keystone2 based SOCs supports 3 instances of i2c controllers. Add
the device nodes for them. The i2c0 child device AT24C1024 EEPROM node
is also added. When different board variants are added in future, it
can be moved to the supported boards from common SOC file.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Now pinctrl-single-omap can handle the wake-up events for us now
as long as the events are configured in the .dts files.
Done in collaboration with Roger Quadros <rogerq@ti.com>.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* SMP support for r8a7791 SoC
* r8a7779_init_irq_extpin() for DT for r8a7779 and r8a7778 SoCs
* Add HPB-DMAC to r8a7779 and r8a7778 SoCs
* Add r7s72100 SoC
* Make use of ARCH timer workaround on r8a7791 SoC
* Add IRQC platform device support to r8a7791 SoC
* Add I2C clocks and aliases for the DT mode for r8a7790 SoC
* Add MAC platform device to r8a73a4 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=4wdR
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Second Round of Renesas ARM based SoC updates for v3.13
* SMP support for r8a7791 SoC
* r8a7779_init_irq_extpin() for DT for r8a7779 and r8a7778 SoCs
* Add HPB-DMAC to r8a7779 and r8a7778 SoCs
* Add r7s72100 SoC
* Make use of ARCH timer workaround on r8a7791 SoC
* Add IRQC platform device support to r8a7791 SoC
* Add I2C clocks and aliases for the DT mode for r8a7790 SoC
* Add MAC platform device to r8a73a4 SoC
* tag 'renesas-soc2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791 SMP support
ARM: shmobile: r8a7779: split r8a7779_init_irq_extpin() for DT
ARM: shmobile: r8a7778: split r8a7778_init_irq_extpin() for DT
ARM: shmobile: r7s72100 SCIF support
ARM: shmobile: Initial r7s72100 SoC support
ARM: shmobile: r8a7791 Arch timer workaround
ARM: shmobile: r8a7791 IRQC platform device support
ARM: shmobile: Introduce r8a7791_add_standard_devices()
ARM: shmobile: Break out R-Car Gen2 setup code
ARM: shmobile: r8a73a4: add a clock alias for the DMAC in DT mode
ARM: shmobile: r8a7790: add I2C clocks and aliases for the DT mode
ARM: shmobile: r8a7779: add HPB-DMAC support
ARM: shmobile: r8a7778: add HPB-DMAC support
ARM: shmobile: r8a73a4: add a DMAC platform device and clock for it
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add support for a new SOCFPGA board that has an Arria V FPGA along with
dual ARM Cortex-A9 cores.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: devicetree@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
The s2f_* clocks are called h2f_* in the datasheets.
Rename them accordingly in the socfpga.dtsi.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Some of the clock nodes and the rst-/sysmgr use wrong indentation.
Fix it.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
This adds basic support for the terasic SoCkit board.
The board includes an Altera Cyclone 5 SoC.
[Dinh Nguyen] - Changed to 115200 for baudrate in dts bootargs
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The current socfpga_cyclone5.dts describes the Altera Cyclone5 SoC Development
Kit. The Cyclone5 includes a SoCFPGA, which itself can be included in other
SoC+FPGA combinations.
Instead of having to describe all Cyclone5 common nodes in every board specific
dts, move socfpga_cyclone5.dts to a dtsi and include this in a new dts for the
Development Kit.
[Dinh Nguyen] - Changed to 115200 for baudrate in dts bootargs
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
- kirkwood
- use MBus DT binding for setting up the windows
- move crypto and nand underneath the mbus node
- ib62x0 has a u-boot env partition
- mvebu
- add the Armada XP matrix board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSVEKbAAoJEAi3KVZQDZAea2cH/0Vshr3Uift/HCY//dBHG91w
OKT539uF4UqTe3B3BmIxGYYpemQMU37R346LPTYiiaTEOCqR90J2sYJKHB+6Yld5
llyI00ulhv6vLVdbGjlLW376lemrilRmH+LRQJdz/UoG64xpJ2RkqATXAQFh1hKi
wLq5heB4T8kfWW3JF52XXR1UTbqJdZyc81gFY9ShSzc78nhyqYJ3MtXN37Cqwqqq
e3izWC9Ujms9maSshY6ENGbOp8vyRslUxcCEFSWChn61fgHVvOA/7zqMRAkts5Ag
cqccsTVR9v2p09O8WvpgM4N9ULwB+qSIS13tVBzOVRGJ3xx+wc8NfBqF/cr3S4I=
=b/Ew
-----END PGP SIGNATURE-----
Merge tag 'dt-3.13-2' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu dt changes for v3.13 (round 2)
- kirkwood
- use MBus DT binding for setting up the windows
- move crypto and nand underneath the mbus node
- ib62x0 has a u-boot env partition
- mvebu
- add the Armada XP matrix board
* tag 'dt-3.13-2' of git://git.infradead.org/linux-mvebu:
arm: mvebu: add support for the Armada XP Matrix board
ARM: kirkwood: ib62x0: add u-boot environment partition
ARM: kirkwood: Move the nand node under the mbus node
ARM: kirkwood: Move the crypto node under the mbus node
ARM: kirkwood: Remove kirkwood_setup_wins and rely on the DT binding
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- mvebu
- add MSI
- new compatible string for mv64xxx-i2c
- dove
- use the pre-processor
- define the MBus nodes
- add PCIe controllers
- add Globalscale D3Plug
- relocate internal registers nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSSaTkAAoJEAi3KVZQDZAeYvgH/iNIksOjc47pf3KDYZLtR2iP
8XYEC3LoxEA6fGJGzJ8AgdWt/V7dq9SRIXE/GxuDCKu/lNzuiBsnigkN9kguSKyA
KqJ7e3n28+3GrTficPyRre24rYwpPKTmlWhrZ4F+TyH42bN4C+TzoW53pNW5MFyv
1FGsUNj2QlzZGcv4CB9JfCWbcgJj2ApB99CB79cd8plrtxj4b1DZ22vxy2sXlSqd
AWMD8kuEaN5zcqpV98znYOEH2RzTnS3XGzG6wrgiulPcsjrLulCDVoMcCkk2jGb8
YaIulucrtvrUQyIcKeB0AvHytcRxsu2N4D6ZtZsJbithgr3tWEusq/fiW22ko68=
=yW5l
-----END PGP SIGNATURE-----
Merge tag 'dt-3.13' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu dt changes for v3.13
- mvebu
- add MSI
- new compatible string for mv64xxx-i2c
- dove
- use the pre-processor
- define the MBus nodes
- add PCIe controllers
- add Globalscale D3Plug
- relocate internal registers nodes
* tag 'dt-3.13' of git://git.infradead.org/linux-mvebu:
ARM: dove: add initial DT file for Globalscale D3Plug
ARM: dove: add PCIe controllers to SoC DT
ARM: dove: relocate internal registers device nodes
ARM: dove: add MBus DT node
ARM: dove: add MBUS_ID macro to Dove DT
ARM: dove: use preprocessor on device tree files
ARM: mvebu: link PCIe controllers to the MSI controller
ARM: mvebu: the MPIC now provides MSI controller features
ARM: dts: mvebu: Update with the new compatible string for mv64xxx-i2c
Signed-off-by: Kevin Hilman <khilman@linaro.org>
As defined in the DT, clkout2 is not allowed to change the pll inside
si5351.
This patch extends the properties of clkout2 so that it works as the
external clock of the audio device in the Cubox.
Also, as the second si5351 clock is not used in the Cubox, its
definition is removed.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch activates the audio device of the Cubox.
The audio flow (pin mpp_audio1) is output on both I2S and S/PDIF.
The third si5351 clock (#2, pin mpp13) is used as the external clock.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds the nodes to instantiate the audio devices of the Dove
boards.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently we get the following errors on imx51-babbage:
/display@di0: could not find display-timings node
/display@di0: no timings specified
/display@di1: could not find display-timings node
/display@di1: no timings specified
imx-drm imx-drm: failed to allocate buffer with size 0
Provide timing values for IPU1, which is connected to a DVI bridge and
to IPU2, which can be connected to the WVGA panel, so that both of them can
be functional.
While at it, disable the WVGA panel, so that DVI output becomes the default one.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for the Tegra124 based Venice2 reference board.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Initial support for Tegra 124 SoC. This is expected to be included in
the board DTS files.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Now since the clock tree is added, update UART dt nodes with clock data
and remove the hard coded clock frequency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
SoC family definitions at the moment are reactive to board needs
as a result, beagle-xm would matchup with ti,omap3 which invokes
omap3430_init_early instead of omap3630_init_early. Obviously, this is
the wrong behavior.
With clock node dts conversion, we get the following warnings before
system hangs as a result and 3630 based platforms fails to boot
(uart4 clocks are only present in OMAP3630 and not present in
OMAP3430):
...
omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
omap_hwmod: uart4: cannot _init_clocks
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434
_init+0x6c/0x80()
omap_hwmod: uart4: couldn't init clocks
...
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: timer12: enabled state can only be entered from
initialized, idle, or disabled state
...
WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224
_idle+0xd4/0xf8()
omap_hwmod: timer12: idle state can only be entered from enabled state
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: uart4: enabled state can only be entered from
initialized, idle, or disabled state
So, add specific compatiblity for 3630 to allow match for Beagle-XM
platform.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: left out ti,omap343x, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this node, there will be no palmas driver to notify
dwc3 that a cable has been connected and, without that, dwc3
will never initialize.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[kishon@ti.com: added dt properties for enabling vbus/id interrupts
and fixed vbus-supply value after SMPS10 is modeled as 2 regulators]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Use a common naming scheme "mode0name.modename flags" for the
USB host pins to be consistent.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds devicetree for gta04 (Openmoko next generation board) with necessary
support for mmc, usb, leds and button.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Populate uarts, timers, rtc, wdt, gpio, i2c, spi, cpsw & pwm nodes.
Reason for adding these nodes early - hwmod code required address
space of peripherals corresponding to these nodes (as address space
details are removed from hwmod database).
uart0, timers - 1 & 2 and synctimer were already present, so here the
remaining uarts & timers are added.
All properties as per the existing binding has been added for uart,
timer, rtc, wdt & gpio. Even though that was not the current scope
of work, felt adding those would reduce or require no effort later
to get these peripherals working.
For i2c, spi, cpsw & pwm - only the properties that were sure to be
correct has been added (main intention is to make hwmod happy and
avoid any later modification to here added properties).
While at it add "ti,hwmod" property to already existing nodes.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Update AM4372 cpu node to the latest cpus/cpu bindings for ARM.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.
Tested on OMAP4 SDP board and Pandaboard ES2.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
SMPS10 has two outputs OUT1 and OUT2. Hence SMPS10 is modeled as
two regulators. The DT node is split to reflect it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Following commit ff5c9059 and therefore other omap platforms using
the gpio-omap driver correct the #interrupt-cells property on am33xx
too. The omap gpio binding documentaion also states that
the #interrupt-cells property should be 2.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
ARM Performance Monitor Units are available on the am33xx,
add the support in the dtsi.
Tested with perf and oprofile on a regular beaglebone.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP COM MOdule has a GPIO LED connected to OMAP
pins. Configure this pin as output GPIO.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEPv2 has a number of GPIO LED connected to OMAP
pins. Configure these pins as output GPIO.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
IGEP boards have a number of LED connected to OMAP or TWL GPIO
lines. The actual wiring is different on each board so each board
DT has need to configure the mux correctly.
Even though it works with the current DT, the kernel complains with:
[2.305023] leds-gpio leds.18: pins are not configured from the driver
Add an empty pinmux_leds_pins pinctrl child node so boards can
override with the correct mux configuration and not depend on
default values for the GPIO LEDs to work.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds device tree with necessary support to boot with functional
video (on both emulator and real N900 device).
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Cubietech introduced a new cubieboard, the CubieTruck. This board added
more output connectors and features 2 GiB of RAM and a Gigabit PHY.
Tested are are uart0 and LEDS which both work as expected.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
dn and dp of USB1 can share with UART1(UART1 can route rx,tx to dn and dp pins of USB1).
here we add this pinmux capability.
USB1/UART1 mode selection has dedicated control register in RSC module, here we attach
the register offset of private data of related pin groups.
Signed-off-by: Rong Wang <Rong.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP(Universal Serial Ports) can be UART as commit 5df831117b,
this patch defines the USP-based UART function pin groups for prima2.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the old codes defined uart0_nostreamctrl_pins, but missed pingroup
and padmux definition for it. this patch fixes it.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the ePAPR spec,
the node name should be "ethernet", not "lan0".
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when the legacy DTS file emev2-kzm9d.dts can be
used with board-kzm9d.c and board-kzm9d-reference.c
proceed with removing emev-kzm9d-reference.dts.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Copy the device nodes from KZM9D reference into the KZM9D
device tree file. This will allow us to use a single DTS
file regarless of kernel configuration. In case of legacy
C board code the device nodes may or may not be used, but
in the multiplatform case all the DT device nodes are used.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Genmai base board support making use of 128 MiB of memory,
the r7s7211 SoC with the SCIF2 serial port and CA9 core.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the r7272100 SoC including:
- Single Cortex-A9 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WVMt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes4-for-v3.12' into soc2-base
Fourth Round of Renesas ARM based SoC fixes for v3.12
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
Add initial support for the r7272100 SoC including:
- Single Cortex-A9 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7779 INTC needs IRL pin mode settings to determine
behavior of IRQ0 - IRQ3. But it depends on platform.
This patch adds status = "disabled" on r8a7779.dtsi as default
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables INTC IRQ and SMSC on BockW board via DT.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the r8a7791 secondary CPU core.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7791 arch timer device tree information.
This needs to be used together with r8a7791 support
code that ties in the R-Car Gen2 arch timer workarounds.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable a r8a7791 IRQC block by adding a device tree
node for the IRQC hardware and pins IRQ0 to IRQ9.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI0 and MMCIF interfaces to armadillo800eva-reference with
regulators and pin configurations. SDHI1 is not added yet, because the
switch, that connects the interface either to an SD slot or to a WiFi
SDIO card cannot be described in DT yet.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the only system DMAC instance on r8a73a4. The RT DMAC
can be added later under the same multiplexer, because they can serve the
same slaves and use the same MID-RID values. Configuration data is
supplied to the driver, using a compatibility match string.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the four I2C interfacces on r8a7790.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently all I2C interfaces in all *.dtsi files for various Renesas SoCs
are enabled by default. Switch them all off and only enable populated I2C
interfaces in board-specific *.dts files.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Add support for r8a7791 SoC
* Rename DU device in clock lookups list of r8a7779 SoC
* USB and SSI/SRU clock support for r8a7778 SoC
* USB phy power control function support for r8a7778 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSSSgvAAoJENfPZGlqN0++QqkP/2qVDvTbeSNq0KpG6nLekj9J
lNl5A5H78q1KxNWMXjxuxU/sTTnEHug0dFXpXTawk4AuunD4hELSaFcqDQc/UKTx
yeSX296yhDDTQo/ZlwwSTLTXI696rYX+WliQ4GgaYEY+Ssl2WtzjML9YI4G+BuO2
DwuBIvbo8V0JLxdoMLFqHAkQiqHFVJlWrnYa4Yp+re5IUzUIbUheHHn2Wu5XjwoJ
BzN+Scsm1uGxSvMXzQ1AwJNBGJpjUQFK353Hp7g54L1kZ/0d9yP9oO5+/7b8r3ev
O2diXHzfwdE9/rTONeLs/B/KpEB6KhIMTqwsdDWijfhIbofRJ8mLj074Abh4zqra
NQTMRX4HfI9qmQrVZFRatKvcR/PgRofSNNaoiIz2Flp0uh8bAgDxTjGegDQUSkyo
l6vTA+Bfrw2LNlvhZLPB8VrlHNJAoP5XgdObUjswFMtwP0E1upx1YW50naVp3Ear
otz700svMBRXqAs6mPsXkgLk/ueqbuPANc26+AHr2q8psOFpcZQKROrHRrxyPxVl
4ZqgEssDB9534A6nct1B0u0eB9pCb95ZcZjuOtdEApXH7hkwp+N40u2orWkSvjhO
cQBdclyk1f9SDVlRVbl5p/iXSUxa3za6dObDKKHSb8OWAOKINIKRcmHEaXtWJycs
yobGmXG8yyAyImBTKxHg
=GB2b
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v3.13' into dt2-base
Renesas ARM based SoC updates for v3.13
* Add support for r8a7791 SoC
* Rename DU device in clock lookups list of r8a7779 SoC
* USB and SSI/SRU clock support for r8a7778 SoC
* USB phy power control function support for r8a7778 SoC
Updated I2C nodes for HDMI-DDC and HDMI-PHY for Arndale board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add pinctrl node for hdmi hpd gpio pin to exynos5420 smdk board
file. hpd Gpio property is added to the hdmi node. This patch also
adds hdmi ddc node.
Both hdmi device and ddc i2c channel are enabled in
exynos5420-smdk5420.dts
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add hdmi and mixer device tree nodes for Exynos 5420 SoC.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds device-tree nodes for the i2c busses on Exynos
5420 platforms.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix wrong clock numbers in hdmi dt node. Removed hdmiphy
clock which was a dummy clock earlier and not required now.
Also added mux clock to change the clock parent.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the mixer clocks to the mixer node in the
exynos 5250 dts file.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add vcc-supply property in the nct1008 node, and set it
as sys_3v3_reg.
change the name of this node to temp-sensor.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
* Add CPU cores to DTSI of r8a7790 SoC
* Add MMCIF and SDHI DT nodes for reference DTS of ape6evm board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=OaGQ
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Renesas ARM-based SoC DT updates for v3.13
* Add CPU cores to DTSI of r8a7790 SoC
* Add MMCIF and SDHI DT nodes for reference DTS of ape6evm board
* tag 'renesas-dt-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Add r8a7790 CA7 CPU cores to DTSI
ARM: shmobile: Add r8a7790 CA15 CPU cores
ARM: shmobile: ape6evm-reference: add MMCIF and SDHI DT nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
* Display Unit support for lager and marzen boards
* Update regulators for MMC0, SDHI0 and SDHI1 on ape6evm board
* Enable use of FPGA on bockw board
* Add sounds support to bockw board
* Add USB function support to bockw board
* Add Koelsch board
* Disable MMCIF command completion signal on ape6evm, armadillo800eva,
kzm9g and lager boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=KUsf
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards
From Simon Horman:
Renesas ARM based SoC board updates for v3.13
* Display Unit support for lager and marzen boards
* Update regulators for MMC0, SDHI0 and SDHI1 on ape6evm board
* Enable use of FPGA on bockw board
* Add sounds support to bockw board
* Add USB function support to bockw board
* Add Koelsch board
* Disable MMCIF command completion signal on ape6evm, armadillo800eva,
kzm9g and lager boards.
* tag 'renesas-boards-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: disable MMCIF Command Completion Signal, add CLK_CTRL2
ARM: shmobile: kzm9g: disable MMCIF Command Completion Signal
ARM: shmobile: armadillo800eva: disable MMCIF Command Completion Signal
ARM: shmobile: ape6evm: disable MMCIF Command Completion Signal
ARM: shmobile: bockw: add USB Function support
ARM: shmobile: Koelsch support
ARM: shmobile: bockw: add R-Car sound support (PIO)
ARM: shmobile: bockw: enable global use of FPGA
ARM: shmobile: lager: Fix Display Unit platform data
ARM: shmobile: ape6evm: update MMC0, SDHI0 and SDHI1 with correct regulators
ARM: shmobile: lager: Add Display Unit support
ARM: shmobile: marzen: Add Display Unit support
ARM: shmobile: r8a7778: add usb phy power control function
ARM: shmobile: r8a7778: add USBHS clock
ARM: shmobile: r8a7791 CMT support
ARM: shmobile: r8a7791 SCIF support
ARM: shmobile: Initial r8a7791 SoC support
ARM: shmobile: r8a7778: add SSI/SRU clock support
ARM: shmobile: r8a7790: Add DU and LVDS clocks
ARM: shmobile: r8a7779: Rename DU device in clock lookups list
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add support for r8a7791 SoC
* Rename DU device in clock lookups list of r8a7779 SoC
* USB and SSI/SRU clock support for r8a7778 SoC
* USB phy power control function support for r8a7778 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=GB2b
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Renesas ARM based SoC updates for v3.13
* Add support for r8a7791 SoC
* Rename DU device in clock lookups list of r8a7779 SoC
* USB and SSI/SRU clock support for r8a7778 SoC
* USB phy power control function support for r8a7778 SoC
* tag 'renesas-soc-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7778: add usb phy power control function
ARM: shmobile: r8a7778: add USBHS clock
ARM: shmobile: r8a7791 CMT support
ARM: shmobile: r8a7791 SCIF support
ARM: shmobile: Initial r8a7791 SoC support
ARM: shmobile: r8a7778: add SSI/SRU clock support
ARM: shmobile: r8a7790: Add DU and LVDS clocks
ARM: shmobile: r8a7779: Rename DU device in clock lookups list
Signed-off-by: Olof Johansson <olof@lixom.net>
* Correct incorrect placement of __initdata tag in ape6evm board code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=nVyt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes5-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
* Correct incorrect placement of __initdata tag in ape6evm board code
* tag 'renesas-fixes5-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: ape6evm: fix incorrect placement of __initdata tag
(+ other patches already present in v3.12-rc4)
Signed-off-by: Olof Johansson <olof@lixom.net>
deletion: this fixes bugs discovered when switching to a
devicetree-only setup, primarily on the HREF prototypes.
The biggest change is to split into four DTS variants as
the UIB autodetection was lost.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xjIK
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Second part of the Ux500 devicetree conversion and ATAG
deletion: this fixes bugs discovered when switching to a
devicetree-only setup, primarily on the HREF prototypes.
The biggest change is to split into four DTS variants as
the UIB autodetection was lost.
* tag 'ux500-devicetree-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: move BU21013 touchpad GPIOs into top-level DTS
ARM: ux500: register the tc35892 GPIO on the TVK UIB
ARM: ux500: split the HREF DTS files from two to four
ARM: ux500: split HREF UIB files
ARM: ux500: move TC35892 at 0x42 to hrefprev60
ARM: ux500: correct CD for micro SD on hrev60plus
ARM: ux500: fix proximity sensor button
ARM: ux500: correct I2C address of ambient light sensor
ARM: ux500 enable the AB8500 gpio for all HREFs
ARM: ux500: add default trigger on HREF LED
Signed-off-by: Olof Johansson <olof@lixom.net>
Rather than requiring each board to explicitly disable the I2S controllers
it is not using instead require boards to enable those that they are using.
This is required for audio operation on Arndale, one of the unused I2S
controllers is pinmuxed with the LDO enable GPIOs for the WM1811A.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On the mx53qsb board with mc34708 PMIC, GPIO1_8 resets the system, so better not
to use it as a wakeup source.
Use GPIO 2_14 and 2_15 for wakeup sources instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
SDHC1 does not have any GPIO for reading the card detection status, so
remove 'cd-gpios'.
After this change card detection works via the internal SD controller mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
SDHC3 is 8 bit-wide, so pass the bus-width property to reflect that.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For consistency and correctness, since this is a bus, even if not
physical, it is worth to add 'reg' property and unit-address to subnodes.
The 'reg' property would merely be an index. Also for consistency, use
"regulator" as node name as used most commonly across other dts files.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This has been done for Arndale board vide commit aa3edb65
("ARM: dts: Put Arndale fixed voltage regulators on a simple-bus").
Replicate here for consistency and correctness.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add PHY provider node for the MIPI CSIS and MIPI DSIM PHYs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The APB2 clocks gates are only a 32 bits register wide, and not 2 as set
currently in the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This board is based on the M28 SoM with custom baseboard. Supported
are LEDs, ethernet, PWM, LCD, SD slots.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Assign a clock for the twd-timer.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
CC: linux-arm-kernel@lists.infradead.org
Split USB2 PHY and USB3 PHY into separate omap-control-usb
nodes. Get rid of "ti,type" property.
CC: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split otghs_ctrl and USB2 PHY power-down into separate
omap-control-usb nodes. Get rid of "ti,type" property.
Also get rid of "ti,has-mailbox" property from usb_otg_hs
node and provide the ctrl-module phandle.
CC: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Armada XP Matrix board is the mother board of a more complex
system. The mother board uses an Armada XP MV78460, 4 serial ports, 2
SATA ports, one Ethernet connection, a PCIe port and a USB port. All
those devices are enabled in the Device Tree added by this patch.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The BU21013 touchscreen GPIOs have been pretty confused, correct
them per board, and move the GPIO assignments up to the top
level DTS file so we can control it from there, and avoid defining
the GPIO assignments for non-ST UIB equipped boards.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TVK1281618 UIB has a TC35892 GPIO expander on it, which has
in the past probably been confused with the GPIO expander on the
older HREF plus previous to v60, which is on an entirely different
part of the system with another I2C address. Register the expander
in the right place.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull (mostly) ARM clocksource driver updates from Daniel Lezcano:
" - Soren Brinkmann added FEAT_PERCPU to a clock device when it is local
per cpu. This feature prevents the clock framework to choose a per cpu
timer as a broadcast timer. This problem arised when the ARM global
timer is used when switching to the broadcast timer which is the case
now on Xillinx with its cpuidle driver.
- Stephen Boyd extended the generic sched_clock code to support 64bit
counters and removes the setup_sched_clock deprecation, as that causes
lots of warnings since there's still users in the arch/arm tree. He
added also the CLOCK_SOURCE_SUSPEND_NONSTOP flag on the architected
timer as they continue counting during suspend.
- Uwe Kleine-König added some missing __init sections and consolidated the
code by moving the of_node_put call from the drivers to the function
clocksource_of_init. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- mvebu
- fix ReadyNAS 102 power button (needs to be active high)
- fix ReadyNAS 102 automated rebooting (prevent hang) by add gpio-poweroff
node
- fix booting ReadyNAS 102 by adding MBus ranges and PCIe DT nodes
- mvebu-mbus: prevent PCIe driver from continuing with corrupted resource
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSTERhAAoJEAi3KVZQDZAeFaQH/jmhAZwvSrB7MeTTY7J9eAcl
n4cFHImBiSb6IdDaocKB+yOmEgq/X2LS/DjK71sa0+CQsTq9B5nHxMHioogdUrG7
S8ofIjqu90CBOZ1I5IMSPmA3uOc1B2+wYi9uLxmajMTzYVDDBEZh9LuMy/GjwzU2
/g09RedQ3XkWDVv3pdPdEiC6KZ/gg7gejxOLv0nv9ydxr0DB8/VwmBHWFC0ghawB
3EchoagJ3M+mAbUaxtY6cauV2nnAJOO5mV6ZHl2tIOj4/Mhn8Le/C1t+Zcdf+U82
iAvqWmiRc3Vk96g8xXZWwZoPL7vhidLcE7dpOIZ2ymq5+g3esTaailqRxRqS9+c=
=uNPR
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.12-2' of git://git.infradead.org/linux-mvebu into fixes
From Jason Cooper:
mvebu fixes for v3.12 (round 2)
- mvebu
- fix ReadyNAS 102 power button (needs to be active high)
- fix ReadyNAS 102 automated rebooting (prevent hang) by add gpio-poweroff
node
- fix booting ReadyNAS 102 by adding MBus ranges and PCIe DT nodes
- mvebu-mbus: prevent PCIe driver from continuing with corrupted resource
* tag 'fixes-3.12-2' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
Signed-off-by: Olof Johansson <olof@lixom.net>
Install targets (install, zinstall, uinstall) on arm have a dependency
to vmlinux. This may cause parts of the kernel to be rebuilt during
installation. We must avoid this since this may run as root. Install
targets "ABSOLUTELY MUST NOT MODIFY THE SOURCE TREE." as Linus
emphasized this in:
http://lkml.org/lkml/2013/7/10/600
So on arm and maybe other archs we need the same as for x86:
1648e4f8 x86, kbuild: make "make install" not depend on vmlinux
This patch fixes this for arm. Dependencies are removed and instead a
check to install.sh is added for the files that are needed.
This issue was uncovered by this build error where the -j option is
used in conjunction with install targets:
$ make <makeflags>
$ make <makeflags> zinstall
...
DEPMOD
Usage: .../scripts/depmod.sh /sbin/depmod <kernelrelease>
(INSTALL_MOD_PATH and INSTALL_PATH variables set, so no root perms
required in this case.)
The problem is that zinstall on arm due to its dependency to vmlinux
does a prepare/prepare3 and finally does a forced rewrite of
kernel.release even if it exists already.
Rebuilding kernel.release removes it first and then recreates it. This
might race with another parallel make job running depmod.
So this patch should fix this one too.
Also quoting $(KERNELRELEASE) arg for install.sh as this messes
argument order in case it is empty (which is the case if the kernel
was not built yet).
Signed-off-by: Robert Richter <robert.richter@linaro.org>
Signed-off-by: Robert Richter <rric@kernel.org>
Acked-by: Michal Marek <mmarek@suse.cz>.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Michal Marek <mmarek@suse.cz>
As the device tree conversion did away with the ability to
auto-detect the UIB (User Interface Board) version from attempting
to read an I2C address, we now have to pass the knowledge of
what UIB is mounted through the device tree. This gives rise
to four possible board permutations:
- HREF prior to v60, ST UIB (hrefprev60-stuib)
- HREF prior to v60, TVK1281618 UIB (hrefprev60-tvk)
- HREF v60 and later, ST UIB (href60plus-stuib)
- HREF v60 and later, TVK1281618 UIB (hrefv60plus-tvk)
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create two different UIB (User Interface Board) include files: one per
UIB simply. The include files now only handle the devices on that
very UIB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TC35892 was mounted as a GPIO expander on the HREF prior
to v60 and not in later versions, which instead use the Nomadik
GPIO directly, so move it over to the hrefprev60 DTS file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This correct the card detect line for the HREF v60 and later
reference designs. This is connected directly to the Nomadik
GPIO block, line 95 at offset 31 on the third instance.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The proximity sensor is connected to pin AH12 on newer HREFs,
that corresponds to pin offset 25 on gpio5, not gpio6.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ambient light sensor is places at address 0x29 nothing else.
This patch makes the ambient light sensor probe again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Zynq is based on an ARM Cortex-A9 MPCore, which features the
arm_global_timer in its SCU. Therefore enable the timer for Zynq.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Add the PSCI binding node for Calxeda SOCs. Only claiming "arm,psci"
support since there is no agreement on 0.2 binding definition.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
There should be no nodes that are not children of the mbus. Move
the nand node under the mbus, and rework the board .dts files
to use an & reference to the nand node.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There should be no nodes that are not children of the mbus. Move
the crypto node under the mbus.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
kirkwood_setup_wins is the last manual caller of mbus in kirkwood, don't
call it for DT boards and rely on the DT having a mbus node with
a proper ranges property to setup these windows.
Move all the mbus ranges properties for all boards into kirkwood.dtsi,
since they are currently all the same.
This makes the DT self consistent, since the physical address of the
NAND and CRYPTO are both referenced internally. The arbitary Linux
constants KIRKWOOD_NAND_MEM_PHYS_BASE and KIRKWOOD_SRAM_PHYS_BASE
no longer have to match the DT values.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is an RFC for the new touchscreen properties.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-input@vger.kernel.org
CC: devel@driverdev.osuosl.org
CC: Marek Vasut <marex@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: devicetree@vger.kernel.org
The delay units inside the LRADC depend on the presence of a 2 kHz clock.
This change enables the clock to be able to use the delay unit for the
touchscreen part of the driver.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When 5e12a613 and 0cd3754a were introduced, Netgear ReadyNAS 102 .dts
file was queued for inclusion and missed the update to have Mbus (and
then BootROM) ranges properties declared. It also missed the relocation
of Armada 370/XP PCIe DT nodes introduced by 14fd8ed0 after de1af8d4.
This patch fixes that which makes 3.12-rc3 bootable on the NAS.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WVMt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes4-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Fourth Round of Renesas ARM based SoC fixes for v3.12
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
* tag 'renesas-fixes4-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
Signed-off-by: Olof Johansson <olof@lixom.net>
the current dts is lacking interrupt and dma prop for video input
processor of prima2 and atlas6, this patch fixes it.
Signed-off-by: Renwei Wu <Renwei.Wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
we lost an address range <0x56000000 0x56000000 0x1b00000> for peri-iobg
of prima2.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Makefile missed to include atlas6-evb.dtb for ARCH_ATLAS6.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
sirf uart and usp-based uart driver with full dma support has
hit 3.12, here we fix the fifosize, dma channels for some HW
prop.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Move all the clock definitions over to the device tree
- Remove all now-redundant AUXDATA and make the ux500 device
tree only
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSRA9cAAoJEEEQszewGV1zpiQP/iwq3mMXJm5NRnG7NdlfaZkO
TUtobAxdTQDbz70nhgLG5z+FD+qxqYed7MnF/NTRIwe6ZsV74lvY4WloAkNizfDL
TeZYxFiSrv5oTHLfJzuynveIflnG0Wfm3MAMFYp3aeR+h9fGrpDkxOlMIleI+BP0
C9wjysYAO2vhAQIUT3ONwybMgPfgsEmQMpMsPzOpfdLmgtqQrELaHmucN8Hghagy
rTwxq6f3gOxYeFAlEAw1RxapH4GI+VBxoLCXGpkTJqhLK4DAo67NphoUPgNAXp7I
IGZwWTYbNVa6GlvLVXFdCmV6UVF+qkTn9/Tedn+a6LF/5XtA44DLGAvhPRZBGdrY
k5nWCyc/90gpDF8pSi7cJkoZLUW3wEwDpYi9XmZA3dsLnbWW3ct8kX3iJNFQ/jAe
lx+kJP9erMQEtiuVfEXXYbK8ILHi8yoEWfiq7FY3UIbHkKIjEdJOCxk5to6BeynA
PKPJNO7dgYdhiM4Rqz4AcF1xCEe5NAQVltNfeqPVg/7o4nlQnIaUQVUpbDnYXaCN
iB0tVbjSiFA4C/C5oz0k2VhKH8YMsgd+CZ9ALS2jhGNiIfFOp8JuuJ8KL86m7iZQ
aC0rPXT8xkEF0a9lVU1UCCiSf6zIpZ0G1iJ6mZ+hA/FJ2pzeLEGEa4iYpsMhcnfQ
0d9fVtYBKBKCMXaeJP0z
=FQfo
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
This is a huge device tree and ATAG removal series for ux500:
- Move all the clock definitions over to the device tree
- Remove all now-redundant AUXDATA and make the ux500 device
tree only
* tag 'ux500-dt-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (92 commits)
ARM: ux500: delete devices-common remnants
clk: ux500: Provide a look-up for the ARMSS clock
ARM: ux500: Enable CPUFreq on Snowball
ARM: ux500: Provide a Device Tree node for CPUFreq in the DBx500
ARM: ux500: Provide a clock lookup for the Hash driver
ARM: ux500: Provide a clock lookup for the Crypto driver
ARM: ux500: Fix trivial white-space error in the DBX500 DTSI file
ARM: ux500: Remove ATAG booting support for Snowball
ARM: ux500: Remove ATAG booting support for HREF
ARM: ux500: Remove ATAG booting support for U8520
ARM: ux500: Remove ATAG booting support for MOP500
ARM: ux500: Purge UIB framework when booting with ATAGs
ARM: ux500: Take out STUIB support when not booting with Device Tree
ARM: ux500: Remove BU21013 ROHM TS support when booting with only ATAGs
ARM: ux500: Don't register the STMPE/SKE when booting with ATAG support
ARM: ux500: Delete U8500 UIB support when booting with ATAGs
ARM: ux500: Don't register Synaptics RMI4 TS when booting with ATAGs
ARM: ux500: Purge DB8500 PRCMU registration when not booting with DT
ARM: ux500: Stop requesting the SoC device to play 'parent' role
ARM: ux500: Remove UART support when booting without Device Tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds an initial DT file for the Globalscale D3Plug with Dove SoC.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds a node for the pcie controllers found on Dove SoCs to the
SoC DT include.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With mbus node in place, now relocate all internal device nodes
to internal-regs node with proper address ranges.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds a MBus node including ranges and pcie apertures required later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds a macro used for defining address window's target ID and
attribute cells for the MBus ranges entry.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This coverts Dove DT board files to preprocessor includes instead
of dtc includes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adjusts the Armada 370 and Armada XP PCIe controllers
Device Tree informations to reference their MSI controller. In the
case of this platform, the MSI controller is implemented by the MPIC.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Daniel Price <daniel.price@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Adds the 'msi-controller' property to the main interrupt controller
Device Tree node, to indicate that it can now behave as a MSI
controller.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: Daniel Price <daniel.price@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Without that fix, at the end of the shutdown process, the board is
still powered (led glowing, fan running, ...).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
NETGEAR ReadyNAS 102 Power button definition in .dts file flags
associated GPIO active low instead of active high. This results
in reversed events reported by input subsystem (0 returned when
the button is pressed, 1 when released). This patch makes
associated GPIO active high to recover correct behaviour.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Koelsch base board support making use of 2 GiB of memory,
the r8a7791 SoC with the SCIF0 serial port and CA15 with
CMT timer.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, dropped not-yet-ready SMP/PFC]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the r8a7791 SoC including:
- Single Cortex-A15 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, dropped not-yet-ready code]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7790 Cortex-A7 CPU information to DTSI.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CA15 CPU cores to r8a7790 for a total of 4 x CA15.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
GPIO3_29 is used to reset the ethernet phy.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
GPIO1_25 is used to reset the ethernet phy.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
MX6QDL_PAD_EIM_D23__GPIO3_IO23 pin is used to reset the ethernet phy.
Add it to the 'hog' group.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Updated the usb_otg_hs dt data to include the *phy* and *phy-names*
binding in order for the driver to use the new generic PHY framework.
Also updated the Documentation to include the binding information.
The PHY binding information can be found at
Documentation/devicetree/bindings/phy/phy-bindings.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For more information about the Udoo board:
http://www.udoo.org/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The AB8500 GPIO was only registered for the pre-v60 HREF but should
be made available on all HREF variants, move the DT entry to the
common file.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is required to fetch the ARMSS clock when booting with DT.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The common clock framework will use the 'clock' property provided to do
a clock lookup when Device Tree is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The common clock framework will use the 'clock' property provided to do
a clock lookup when Device Tree is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MTU0 is required for full booting of the system. The driver has
been previously DT:ed and is in use on the Nomadik platform, but we
also need to enable it on ux500 based systems.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The "mentor,musb" binding isn't documented so I was about
to document it.
The node is missing a few properties for configuration like
"multipoint", "dyn_fifo", "num_eps" or "ram_bits". However
I am not sure "missing" is the right word here because some
of those informations might be obtained from the chip itself
but it is not done (yet).
Further the ePARP 2.3.1 says the matching goes from left to
right taking the fist match. Right now there is jus a driver
for "stericsson,db8500-musb" and none for "mentor,musb".
I'm not 100% that it is simply possible to have a generic
since even for DMA we have ifdefs in the driver between
"generic mentor dma" and "ux500 dma" and I mean within musb
and not the dma code.
For that reason (that I am not sure a generic musb binding
is possible and how its binding / required properties will
look like) and the reason that we have here a minor binding
without a driver to look at I suggest to remove that binding.
If the majority of people prefer to keep this binding I'm
curious how the documentation of the binding should look like.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These regulator rail names are already set in the
ste-href.dtsi file included by this file, this is just redoing
the naming for no benefit, so delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Ux500 boards are layered like this:
ste-snowball.dts includes ste-href.dtsi that includes
ste-dbx500.dtsi.
The dbx500.dtsi defines the PRCMU SoC regulators so the SoC will
probe and you can use ampersand references where need be.
However the HREF common dtsi and these two boards redefine the
same PRCMU SoC regulators with the very same names and properties
for no reason. This is like filling in the same line three
times instead of drawing it once. Just delete the surplus
references and have the PRCMU regulators defines in the SoC
files ste-dbx500.dtsi, this is enough.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Turns out that they're actually not required and the driver probes just
fine without them. The ID is incorrect at the moment anyway. They actually
currently specify the stn8815.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial PHYTEC VF610 Cosmic/Cosmic+ board support with
UART and FEC enabled.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This pin definition had been added after the initial patch to use
symbolic pin names in DTS files.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Update the Ka-Ro TX28 DTS file.
- add Copyright header
- use label references for better readability
- sort the entries alphabetically
- add some aliases used by U-Boot to modify the DT data
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For some reason, the select input of pin function USB_OTG_ID is not
implemented via a regular select input register but using the bit
USB_OTG_ID_ SEL (shift 13) of IOMUXC_GPR1 register (offset 0x4).
As per the workaround for such quirk implemented in pinctrl driver,
we need to compose the input_val cell as below.
31 23 15 7 0
| 0xff | shift | width | select |
Thus, we have 0xff0d0100 for MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID and
0xff0d0101 for MX6QDL_PAD_GPIO_1__USB_OTG_ID in input_val cell.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Convert mx23/mx28 dts files to use the padconfig defintions from
mxs-pinfunc.h.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Convert mx23/mx28 dts filed to use the pinctrl header files.
NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts
According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX
I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Remove the list of possible pin configurations from the documentation
file and create header files containing those definitions.
This eliminates the need for error-prone manual lookup of those values
in the documentation and guarantees consistency between the human
readable representation of the pad function in the .dts file and the
actual binary value used in DT.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Provide 'lradc-touchscreen-wires' property to the LRADC driver, so that
touchscreen can be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On imx6qdl-sabresd the SDHC2 and SDHC3 are 8 bit-wide, so pass the bus-width
property to reflect that.
Otherwise the mmc driver will operate with the default bus-width value of 4.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is needed for supporting ultra high speed cards like SD3.0 cards.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable USB function for OTG 1 and OTG 2 at mx6sololite evk.
Besides, fix the wrong interrupt number for OTG2 and host 1.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6q-sabrelite board can be connected to a 1024x768 Hannstar LVDS panel.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Put the nodes in alphabetical order so that further node additions can be better
organized.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Trying to use the usb otg port on mx53qsb results in the following error:
$ modprobe g_ether
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 52:0f:8a:1e:aa:09
usb0: MAC de:f3:70:d8:6c:62
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
(Connect the USB cable)
$ ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11
USB otg port goes to connector J3 (mini USB) and also to the USB combo (J2).
As mx53qsb does not provide a USB ID pin, pass the dr_mode as 'peripheral' so
that we can have usb device working.
Tested via g_ether.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested via g_ether:
$ modprobe g_ether
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 42:b5:26:a9:48:21
usb0: MAC 36:a6:85:9b:9e:13
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
$ g_ether gadget: high-speed config #1: CDC Ethernet (ECM)
$ ifconfig usb0 10.0.0.2
Then on the PC host side:
~$ sudo ifconfig usb0 10.0.0.1
~$ ping 10.0.0.2
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
64 bytes from 10.0.0.2: icmp_req=1 ttl=64 time=1.26 ms
64 bytes from 10.0.0.2: icmp_req=2 ttl=64 time=0.280 ms
64 bytes from 10.0.0.2: icmp_req=3 ttl=64 time=0.297 ms
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
RTS/CTS pins can be used for different purposes, so create separate
definitions for these pins.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
the kernel.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=r6/u
-----END PGP SIGNATURE-----
Merge tag 'del-shark-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
From Linus Walleij:
This deletes the Shark SA110-based sub-architecture from
the kernel.
* tag 'del-shark-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
video: drop code for ARCH_SHARK in cyber2000fb
input: i8042: drop dependency on ARCH_SHARK
ide: drop dependency on ARCH_SHARK
block: drop dependency on ARCH_SHARK
MAINTAINERS: delete Shark machine entry
ARM: delete mach-shark
Signed-off-by: Olof Johansson <olof@lixom.net>
- Supply SD/MMC voltage from the VMMC regulator
- Delete auxdata for SD/MMC card and rely on DT only
- Update device tree for FSMC NAND merged for v3.12-rc1
- Delete auxdata for FSMC NAND
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSQef2AAoJEEEQszewGV1z4h4QALU3BRLoE8Ostv2U5pAWWoiU
JIBaSyHT6Oj8A8Mbrb1kpFxHoPqxD3zbdQ3jNBPeMkHzL+vKszHDzu81wl3dYDNt
3p1fNu59YYDM72p8qyC9CwJosYq4nGeONT+U6bzBg0vvI1JEQkcP7/LTlUOvrNeq
zSps6bBmdpObcxnPf03fBHo4JWZ79v4BmQSIskdP0yYrgR1mguBDZxT6rlT0twNo
JWh14LGLAZ2TG8OsFZrPqP26yfYOqb/KypHUgEyoyW+vODlENvmRcbrNuzziBxp1
yIXTdCrCm+mVoxRUzPJm/ZfyUUkjqgbhlc9sPBIsx0cGyD5JjHd7jc9CCN+C7Uz/
sDCDCu4UzaXoYXt3gk20hmuDR9PZQfklz4u/hKLsMY0i0yOnCTWPUyuM1cnCeyW9
lumhKWopYJ67eRHUvl3AAugh8QmTJ1BGVBU3aQ59WeHhqAGgHEH8djI7rpPBQw85
JU1kgj7g9RuHys9vWJXpGTDK3TYQfp+fQ2moS7+YWAZWOrkGQaba7byFJDKnXiD2
aljaXmyi8/thA0oui+GPwpojC8A33Pm5z3JhZuKBDdKh9sFk7dsX+2fzLxqLkWPe
D5A5op0QV7aD1RHQMlGhG95afouvRk64enRgqCZfrc0jkLYIzL7cNZms3I7YaIX1
O+TmM2swt1G+ohnB5plR
=Kbwg
-----END PGP SIGNATURE-----
Merge tag 'for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/cleanup
From Linus Walleij:
These three patches tear out the remaining AUXDATA in the
Nomadik platform and replace it with device tree.
Corresponding driver changes are coming from respective
subsystem tree and there are no build dependencies.
- Update device tree for VMMC regulator data
- Supply SD/MMC voltage from the VMMC regulator
- Delete auxdata for SD/MMC card and rely on DT only
- Update device tree for FSMC NAND merged for v3.12-rc1
- Delete auxdata for FSMC NAND
* tag 'for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: delete FSMC platform data
ARM: nomadik: delete MMCI platform data
ARM: nomadik: register VMMC regulator
Signed-off-by: Olof Johansson <olof@lixom.net>
- add device tree infrastructure for s3c64xx
- add DT SoC file for s3c64xx
- add DT board file for FriendlyARM Mini6410 board
- add DT board file for SAMSUNG SMDK6410
Based on Common Clk Framework for S3C64XX
- this branch is on top of v3.13-next/common-clk-s3c64xx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WzM4
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-s3c64xx' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Add device tree support for S3C64XX
- add device tree infrastructure for s3c64xx
- add DT SoC file for s3c64xx
- add DT board file for FriendlyARM Mini6410 board
- add DT board file for SAMSUNG SMDK6410
Based on Common Clk Framework for S3C64XX
* tag 'samsung-dt-s3c64xx' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add dts file for S3C6410-based SMDK6410 board
ARM: dts: Add dts file for S3C6410-based Mini6410 board
ARM: dts: Add basic dts include files for Samsung S3C64xx SoCs
ARM: S3C64XX: Add board file for boot using Device Tree
gpio: samsung: Skip initialization if device tree is present
ARM: S3C64XX: Bypass legacy initialization when booting with DT
irqchip: vic: Parse interrupt and resume masks from device tree
ARM: S3C64XX: Remove old clock management code
ARM: S3C64XX: Migrate clock handling to Common Clock Framework
usb: ohci-s3c2410.c: Use clk_prepare_enable/clk_disable_unprepare
ARM: S3C64XX: Use clk_prepare_enable/clk_disable_unprepare in dma.c
ARM: SAMSUNG: Add soc_is_s3c6400/s3c6410 macros
Signed-off-by: Olof Johansson <olof@lixom.net>
- removal of void IRQF_DISABLED flag in timer drivers
- two little fixes in DT for at91sam9x5 family
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSQYrTAAoJEAf03oE53VmQ8n4IAIV0bJHRvpUQ9fGfMH3xoKuF
/Frb+HyPDQpPRPN3k6CaZSOa5P68d6WsC/Livw7HVcxwphI+BkCM4joHyeRCgH7G
RBbWPoscr1mKBZqha7s7+D5n9uxR5Zrxw2emlWnpoZCHpgaUcsZKaSYA1xbONO6o
OBlDffrXgf3vobepEFSLqYGHkQ5nyyegBJB6MLcFh7ceksOOb5cxT4G52Fan7T+U
JciaG8baO9WPKiMlcWpvFQ7Kys7zxqKzu1ILxolfUP8Rz+c/YAtb3pHsKrb6oo/D
lD+682L1sqaKtdYlnSiPM9rVEX929cwShcABt0Q5e//11uvVRG9AN/1Hh1rzMVs=
=bhiP
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre, first fixes series for 3.12:
- removal of void IRQF_DISABLED flag in timer drivers
- two little fixes in DT for at91sam9x5 family
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: remove IRQF_DISABLED
ARM: at91: at91sam9x5: set default mmc[01] pinctrl-names
ARM: at91: serial: fix wrong pinctrl_usart2_rts
Signed-off-by: Olof Johansson <olof@lixom.net>
Use a standard 'qcom' prefix to denotate device trees meant for Qualcomm
based processors.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
We now have device tree support for setting the NAND timings
for FSMC from the device tree, so delete the last piece of
platform data and auxdata.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add DT entries for the phy mode selection in AM33xx SoC using cpsw-phy-sel
driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This property is no longer required by the GPIO binding. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently DT compatibility strings of both types can be found in the kernel
sources: <unit>-<soc> and <soc>-<unit>, whereas a unique format should be
followed and the former one is preferred. This patch converts the SDHI
MMC driver and its users to the common standard. This is safe for now, since
ATM no real products are using this driver with DT.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[Removed r8a7740.dtsi portion as it is not applicable]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- mvebu
- fix reference leaks by adding of_node_put()
- update Armada XP DT clock properties to restore booting
- kirkwood
- add missing reg property for cpu@0
- fix typo in address of second XOR engine
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSO8JQAAoJEAi3KVZQDZAe660IAJV2Zqc/iMxmRJLCPoFnSpGd
uFsthQx0e+OGVW+KowykPve2p6RxOqol2wR1IvgMlkCPFBtUGhGkEeXvJ1wenS9H
JNEtG7fU6AAiaw9dfS6OJtPMxQK3yTSjkVcuaNi0Ds/q99ja9ZYR6RPYzqe8kQME
k9dX3OGNzm+nI7BKheVYcB4zmxBfCtSHzBe2tdwK6mdoki9Qdt4FY4LosXwQHt4d
5BjHGLLgbOp/fCrztgYD4ZiuuJekXz51OP1ut2giIdlakgW0DIRCRadyLyyZMH7S
Wrl636TaYAdh/jXu00mTZIj13K0NDXcERjemjb7O16LFB0fAIz+DYXVVM2nB1iE=
=B2UP
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.12' of git://git.infradead.org/linux-mvebu into fixes
From Jason Cooper, mvebu fixes for v3.12:
- mvebu
- fix reference leaks by adding of_node_put()
- update Armada XP DT clock properties to restore booting
- kirkwood
- add missing reg property for cpu@0
- fix typo in address of second XOR engine
* tag 'fixes-3.12' of git://git.infradead.org/linux-mvebu:
ARM: kirkwood: Fix address of second XOR engine
ARM: mvebu: Add clock properties to Armada XP timer node
ARM: mvebu: Add the reference 25 MHz fixed-clock to Armada XP
ARM: Kirkwood: Add missing DT reg property to cpu@0
bus: mvebu: add missing of_node_put() to fix reference leak
ARM: mvebu: add missing of_node_put() to fix reference leak
Signed-off-by: Olof Johansson <olof@lixom.net>
There appears to be an error in the second address of the second XOR
engine in the Kirkwood SoC device tree, which is specified as 0xd0b00
but should be 0x60b00.
For confirmation of address see table 581 page 658 of:
http://www.marvell.com/embedded-processors/kirkwood/assets/FS_88F6180_9x_6281_OpenSource.pdf
Also see definition of XOR1_HIGH_PHYS_BASE in
arch/arm/mach-kirkwood/include/mach/kirkwood.h
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds MMCIF0, SDHI0 and SDHI1 DT nodes and a fixed voltage
reglator for them to the ape6evm-reference platform.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In place of hardcoding the key code in DTS file and comment the
key code as side notes, use the key code macro defines in the
dt-bindings/input/input.h directly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add Palmas pincontrol to Dalmore device tree and make following
configuration as default:
- Disable DVFS1 and DVFS2.
- Set GPIO6 to gpio mode.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Replace pinctrl_usart2_rts and pinctrl_usart2_cts istead of pinctrl_uart2_*.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
regressions and avoid electrical issues on beaglebone black.
Via Benoit Cousson <bcousson@baylibre.com>:
Fix BBB LDO voltage to avoid HDMI destruction
Fix OMAP5 wrong attribute
Fix typo in beagle xM strings
Fix missing pinmux and regulator for OMAP4 wifi
Fix missing pinmux for igep headset
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSOgVFAAoJEBvUPslcq6VzUHEP/RqHFV7w7DIqxLF+sCpSB8Kk
nfhB+z/3oH3JL63kFahvKMsaFQidI7djyTXISTnt1d0z1M35CN2UleRz7Jp2GoKU
dRYonilBIchAgy2R9oFuOsDlUYk8ANpGUI5x5HSN34v2cyqtmSea14Boz9oIHecT
qU8T4zg4GgOPKqUQtQrec80m2JtsVEum/kyyUcgrydsFF2guBShbtL0HqFZDT9i3
7e9MJg2WBpV8QyH3/BkZnzyUMgiXQyq/LBM0As3J+FfZi+3dSh0yHRRiZuaSprfv
t6JDgMwn5erAh1dkAmETHU9o+BUKIqXu58+xMSDp2G/DhidoMqBZ9AIgFz/GHZhn
mHuXcWw4nmwaHTwV4LzjhML284EE9GUqbc1UEV0ZoX0YRRiVPt5gSn1dsLsv34cp
4s22C7d8c/w24s4Z8qSW5OtTl+o8CeYYtyR4ppJMetVXcDXycEZ9xFTGjDkbGibg
6W42FsAQ0ExG2EX3zSY0bicUUTX78liNDimwucu1YQjz9j2zw2glQdA4uz/YJBvb
/sd1T9DcdoU3Pmng2/QJ+zFoIKM7EkHUUICVwuH1Qki8pmmqcLuBiUIqxC8BFFYB
VXjbyh+TlToqFeY87JKAk3croFPoWNrsPayBut4P7VjsgZTScMj0oo0wbTsVdM3E
vizBBHgKA604b6pG45Zv
=JZua
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/fixes-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren, OMAP DT fixes for 3.12-rc1:
OMAP device tree changes that are needed to fix regressions and avoid
electrical issues on beaglebone black.
Via Benoit Cousson <bcousson@baylibre.com>:
Fix BBB LDO voltage to avoid HDMI destruction
Fix OMAP5 wrong attribute
Fix typo in beagle xM strings
Fix missing pinmux and regulator for OMAP4 wifi
Fix missing pinmux for igep headset
* tag 'omap-for-v3.12/fixes-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: igep00x0: Add pinmux configuration for MCBSP2
ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for blaze
ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for pandaboard
ARM: dts: OMAP5: fix ocp2scp DTS data
ARM: dts: OMAP5: fix reg property size
ARM: dts: am335x-bone*: add DT for BeagleBone Black
ARM: dts: omap3-beagle-xm: fix string error in compatible property
Signed-off-by: Olof Johansson <olof@lixom.net>
With the addition of the Armada XP reference clock, we can now model
accurately the available clock inputs for the timer: namely, nbclk
and refclk. For each of this clock inputs we assign a name, for the
driver to select as appropriate.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP SoC has a reference 25 MHz fixed-clock that is used in
some controllers such as the timer and the watchdog. This commit adds
a DT representation of this clock through a fixed-clock compatible node.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The kirkwood.dtsi cpu@0 node is missing the mandatory reg property.
This causes of_get_cpu_node() to fail to find the node and as a result
the cpufreq driver fails in its probe function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The A20-olinuxino-micro uses the first three I2C controllers found on
the A20. Enable them in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 boards we currently have share the same pins for the i2c
controllers they share. Add them to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A20 shares the same I2C controller than the one that could
be found on earlier SoCs from Allwinner. There is only a few more of
these controllers. Add all of them in the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add pinmux configuration for MCBSP2 connected to the TDM interface.
With this configuration the Headset modules works as expected.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Commit 76787b3b (ARM: OMAP2+: Remove board-4430sdp.c)
removed legacy booting in favor of device tree based booting
for 4430sdp. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.
I don't have the "1283 PG 2.21 connectivity device" on my 4430sdp,
but the earlier version of this patch was tested by Luciano
Coelho. This version has left out the input logic for MMC CLK
line compared to the earlier version as that is not bidirectional,
and should be safe to do.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Cc: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Commit b42b9181 (ARM: OMAP2+: Remove board-omap4panda.c)
removed legacy booting in favor of device tree based booting
for pandaboard. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.
The legacy muxing was setting pulls for GPIO 48 and 49, so let's
keep that behaviour for now to avoid further regressions for
BT and FM. Also input logic was enabled for MMC CLK line, but
I've verified that the input logic we don't need enabled for
CLK line as it's not bidirectional.
Also, we want to use non-removable instead of ti,non-removable
as the ti,non-removable also sets no_regulator_off_init which
is really not what we want as then wl12xx won't get powered
up and down which is needed for resetting it.
Note that looks like the WLAN interface fails to come up after
a warm reset, but that most likely was also happening with
the legacy booting and needs a separate fix.
Cc: Paolo Pisati <p.pisati@gmail.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The mv64xxx-i2c embedded in the Armada XP have a new feature to
offload i2c transaction. This new version of the IP come also with
some errata. This lead to the introduction to a another compatible
string.
This commit split the i2c information into armada-370.dtsi and
armada-xp.dtsi. Most of the data remains the same and stay in the
common file Armada-370-xp.dtsi. With this new feature the size of the
registers are bigger for Armada XP and the new compatible string is
used.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
