Commit Graph

22966 Commits

Author SHA1 Message Date
Badhri Jagan Sridharan
1373fefc62 usb: typec: tcpm: Allow slow charging loops to comply to pSnkStby
When a PD charger advertising Rp-3.0 is connected to a sink port, the
sink port current limit would 3A, during SNK_DISCOVERY, till power
negotiation starts. Once the negotiation starts the power limit needs
to drop down to pSnkStby(500mA @ 5V) and to negotiated current limit
once the explicit contract is in place. Not all charging loops can ramp
up to 3A and drop down to 500mA within tSnkStdby which is 15ms. The port
partner might hard reset if tSnkStdby is not met.

To solve this problem, this patch introduces slow-charger-loop which
when set makes the port request PD_P_SNK_STDBY_MW upon entering
SNK_DISCOVERY(instead of 3A or the 1.5A during SNK_DISCOVERY) and the
actual currrent limit after RX of PD_CTRL_PSRDY for PD link or during
SNK_READY for non-pd link.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-14 16:27:29 +02:00
Badhri Jagan Sridharan
1230868433 usb: typec: tcpm: Honour pSnkStdby requirement during negotiation
>From PD Spec:
The Sink Shall transition to Sink Standby before a positive or
negative voltage transition of VBUS. During Sink Standby
the Sink Shall reduce its power draw to pSnkStdby. This allows
the Source to manage the voltage transition as well as
supply sufficient operating current to the Sink to maintain PD
operation during the transition. The Sink Shall
complete this transition to Sink Standby within tSnkStdby
after evaluating the Accept Message from the Source. The
transition when returning to Sink operation from Sink Standby
Shall be completed within tSnkNewPower. The
pSnkStdby requirement Shall only apply if the Sink power draw
is higher than this level.

The above requirement needs to be met to prevent hard resets
from port partner.

Without the patch: (5V/3A during SNK_DISCOVERY all the way through
explicit contract)
[   95.711984] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[   95.712007] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[   95.712017] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[   95.837190] VBUS on
[   95.882075] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[   95.882082] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS]
[   95.882086] polarity 1
[   95.883151] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0
[   95.883441] enable vbus discharge ret:0
[   95.883445] Requesting mux state 1, usb-role 2, orientation 2
[   95.883776] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[   95.883879] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS]
[   96.038960] VBUS on
[   96.383939] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms]
[   96.383946] Setting voltage/current limit 5000 mV 3000 mA
[   96.383961] vbus=0 charge:=1
[   96.386044] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
[   96.386309] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS]
[   96.394404] PD RX, header: 0x2161 [1]
[   96.394408]  PDO 0: type 0, 5000 mV, 3000 mA [E]
[   96.394410]  PDO 1: type 0, 9000 mV, 2000 mA []
[   96.394412] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION]
[   96.394416] Setting usb_comm capable false
[   96.395083] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1
[   96.395089] Requesting PDO 1: 9000 mV, 2000 mA
[   96.395093] PD TX, header: 0x1042
[   96.397404] PD TX complete, status: 0
[   96.397424] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION]
[   96.400826] PD RX, header: 0x363 [1]
[   96.400829] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION]
[   96.400832] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION]
[   96.577315] PD RX, header: 0x566 [1]
[   96.577321] Setting voltage/current limit 9000 mV 2000 mA
[   96.578363] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0
[   96.578370] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION]

With the patch:
[  168.398573] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[  168.398605] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[  168.398619] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[  168.522348] VBUS on
[  168.568676] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[  168.568684] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS]
[  168.568688] polarity 1
[  168.569867] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0
[  168.570158] enable vbus discharge ret:0
[  168.570161] Requesting mux state 1, usb-role 2, orientation 2
[  168.570504] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[  168.570634] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS]
[  169.070689] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms]
[  169.070695] Setting voltage/current limit 5000 mV 3000 mA
[  169.070702] vbus=0 charge:=1
[  169.072719] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
[  169.073145] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS]
[  169.077162] PD RX, header: 0x2161 [1]
[  169.077172]  PDO 0: type 0, 5000 mV, 3000 mA [E]
[  169.077178]  PDO 1: type 0, 9000 mV, 2000 mA []
[  169.077183] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION]
[  169.077191] Setting usb_comm capable false
[  169.077753] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1
[  169.077759] Requesting PDO 1: 9000 mV, 2000 mA
[  169.077762] PD TX, header: 0x1042
[  169.079990] PD TX complete, status: 0
[  169.080013] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION]
[  169.083183] VBUS on
[  169.084195] PD RX, header: 0x363 [1]
[  169.084200] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION]
[  169.084206] Setting standby current 5000 mV @ 500 mA
[  169.084209] Setting voltage/current limit 5000 mV 500 mA
[  169.084220] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION]
[  169.260222] PD RX, header: 0x566 [1]
[  169.260227] Setting voltage/current limit 9000 mV 2000 mA
[  169.261315] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0
[  169.261321] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION]
[  169.261570] AMS POWER_NEGOTIATION finished

Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-14 16:27:29 +02:00
Thinh Nguyen
475e8be53d usb: dwc3: gadget: Check for disabled LPM quirk
If the device doesn't support LPM, make sure to disable the LPM
capability and don't advertise to the host that it supports it.

Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9e68527ff932b1646f92a7593d4092a903754666.1618366071.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-14 15:58:33 +02:00
Sandeep Maheswaram
568262bf54 usb: dwc3: core: Add shutdown callback for dwc3
This patch adds a shutdown callback to USB DWC core driver to ensure that
it is properly shutdown in reboot/shutdown path. This is required
where SMMU address translation is enabled like on SC7180
SoC and few others. If the hardware is still accessing memory after
SMMU translation is disabled as part of SMMU shutdown callback in
system reboot or shutdown path, then IOVAs(I/O virtual address)
which it was using will go on the bus as the physical addresses which
might result in unknown crashes (NoC/interconnect errors).

Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Link: https://lore.kernel.org/r/1618380209-20114-1-git-send-email-sanm@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-14 15:58:06 +02:00
Thinh Nguyen
e66bbfb0fb usb: dwc3: gadget: Ignore Packet Pending bit
Currently the controller handles single stream only. So, Ignore Packet
Pending bit for stream selection and don't search for another stream if
the host sends Data Packet with PP=0 (for OUT direction) or ACK with
NumP=0 and PP=0 (for IN direction). This slightly improves the stream
performance.

Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/097ba9e104c143f7ba0195ebff29390ec3043692.1618282705.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-14 15:57:44 +02:00
Kai-Heng Feng
8f23fe35ff USB: Add LPM quirk for Lenovo ThinkPad USB-C Dock Gen2 Ethernet
This is another branded 8153 device that doesn't work well with LPM
enabled:
[ 400.597506] r8152 5-1.1:1.0 enx482ae3a2a6f0: Tx status -71

So disable LPM to resolve the issue.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1922651
Link: https://lore.kernel.org/r/20210412135455.791971-1-kai.heng.feng@canonical.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-14 15:17:53 +02:00
Dan Carpenter
434438d8f9 usb: typec: silence a static checker warning
Smatch complains about a potential missing error code:

    drivers/usb/typec/port-mapper.c:168 typec_link_port()
    warn: missing error code 'ret'

This is a false positive and returning zero is intentional.  Let's
re-arrange the code to silence the warning and make the intent more
clear.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YHadaACH8Mq/10F7@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-14 15:15:40 +02:00
Artur Petrosyan
401411bbc4 usb: dwc2: Add exit clock gating before removing driver
When dwc2 core is in clock gating mode loading driver
again causes driver fail. Because in that mode
registers are not accessible.

Added a flow of exiting clock gating mode
to avoid the driver reload failure.

Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073731.3C81BA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:12 +02:00
Artur Petrosyan
ef5e0eec47 usb: dwc2: Add clock gating exiting flow by system resume
If not hibernation nor partial power down are supported,
port resume is done using the clock gating programming flow.

Adds a new flow of exiting clock gating when PC is
resumed.

Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073723.BA0FEA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:12 +02:00
Artur Petrosyan
50fb0c128b usb: dwc2: Add clock gating entering flow by system suspend
If not hibernation nor partial power down are supported,
clock gating is used to save power.

Adds a new flow of entering clock gating when PC is
suspended.

Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073716.30C13A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:12 +02:00
Artur Petrosyan
16c729f90b usb: dwc2: Allow exit clock gating in urb enqueue
When core is in clock gating state and an external
hub is connected, upper layer sends URB enqueue request,
which results in port reset issue.

Added exit from clock gating state to avoid port
reset issue and process upper layer request properly.

Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073708.ADFC6A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:12 +02:00
Artur Petrosyan
3cf8143e47 usb: dwc2: Update exit clock gating when port is resumed
Updates the implementation of exiting clock gating mode
when core receives port resume.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_exit_clock_gating()" function.

Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073701.367E0A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:12 +02:00
Artur Petrosyan
d37b939cf4 usb: dwc2: Update enter clock gating when port is suspended
Updates the implementation of entering clock gating mode
when core receives port suspend.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_enter_clock_gating()" function.

Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073653.9F493A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:12 +02:00
Artur Petrosyan
5f9e60c061 usb: dwc2: Add exit clock gating when port reset is asserted
Adds clock gating exit flow when set port feature
reset is received in suspended state.

Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073646.27217A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:12 +02:00
Artur Petrosyan
9b4965d77e usb: dwc2: Add exit clock gating from session request interrupt
Added clock gating exit flow from session
request interrupt handler according programming guide.

Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073638.921E8A0099@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:12 +02:00
Artur Petrosyan
5d240efddc usb: dwc2: Add exit clock gating from wakeup interrupt
Added exit from clock gating mode when wakeup interrupt
is detected. To exit from the clock gating
in device mode "dwc2_gadget_exit_clock_gating()"
function is used with rem_wakeup parameter 0. To exit
clock gating in host mode "dwc2_host_exit_clock_gating()"
with rem_wakeup parameter 1.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073630.EF2CEA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:11 +02:00
Artur Petrosyan
cbe1e903e5 usb: dwc2: Allow entering clock gating from USB_SUSPEND interrupt
If core doesn't support hibernation or partial power
down power saving options, power can still be saved
using clock gating on all the clocks.

- Added entering clock gating state from USB_SUSPEND
  interrupt.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073623.65355A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:11 +02:00
Artur Petrosyan
79c87c3c37 usb: dwc2: Add host clock gating support functions
Added host clock gating support functions according
programming guide.

Added function names:
dwc2_host_enter_clock_gating()
dwc2_host_exit_clock_gating()

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073615.B3E84A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:11 +02:00
Artur Petrosyan
012466fc8c usb: dwc2: Add device clock gating support functions
Added device clock gating support functions according
programming guide.

Moved "bus_suspended" flag to "dwc2_hsotg" struct because
we need to set that flag while entering to clock gating
in case when the driver is built in peripheral mode.

Added function names:
dwc2_gadget_enter_clock_gating()
dwc2_gadget_exit_clock_gating()

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073607.F41E8A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-13 12:25:11 +02:00
Greg Kroah-Hartman
9bc46a12c5 Several Cadence3 improvements are introduced in v5.13-rc1:
- Add recovery during resume if the controller was lost power at system suspend
 - Reduce DMA memory footprint
 - Other small improvements
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmB0S50ACgkQSFkpgVDW
 cbthMggAnH0oPq93dipS9g2WhHxmwKGJimWTFU82RxuuX6MefvllXEkWCHJdPplp
 dyKhzaFQxFksR7GJ8UCoZg3wg0rk38suLiN+W+k9re6QaHPFWJiMEm83mN3/YaNn
 stVLiuMRl+VIApIIWbf3MW8/a3j9N5oRI+MbqmvhcA4TFu3Z1xTe9xhs8eDtzeUV
 cGI6JbrZr5Q3pcsvvZPwj2nFgjJ7eYum9Z1CsAopHyVnYu/NK2jh2+W+L37dUSan
 cwUOIRoNvSYNHyXFVszOEmfxtTAKiISQ7L4+8tXr4X+qC8tUNd8Rw1ow5BAo8gh+
 bBL8+NZVVGoTvNpYPhLLUHncE5Fn9Q==
 =+ZMP
 -----END PGP SIGNATURE-----

Merge tag 'usb-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next

Peter writes:

Several Cadence3 improvements are introduced in v5.13-rc1:
- Add recovery during resume if the controller was lost power at system suspend
- Reduce DMA memory footprint
- Other small improvements

* tag 'usb-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
  usb: cdnsp: Fixes issue with Configure Endpoint command
  usb: cdnsp: remove redundant initialization of variable ret
  usb: cdns3: delete repeated clear operations
  usb: cdns3: Optimize DMA request buffer allocation
  usb: cdns3: Use dma_pool_* api to alloc trb pool
  usb: cdns3: fix static checker warning.
  usb: cdns3: imx: mark cdns_imx_system_resume as __maybe_unused
  usb: cdns3: trace: delete the trace parameter for request->trb
  usb: cdns3: imx: add power lost support for system resume
  usb: cdns3: add power lost support for system resume
2021-04-12 16:21:35 +02:00
Greg Kroah-Hartman
5bdb080f96 Revert "usb: Link the ports to the connectors they are attached to"
This reverts commit 63cd786173 as it
causes a build error:
	depmod: ERROR: Cycle detected: usbcore -> typec -> usbcore
	depmod: ERROR: Found 2 modules in dependency cycles!

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20210412213655.3776e15e@canb.auug.org.au
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-12 14:36:02 +02:00
Pawel Laszczak
10076de33b
usb: cdnsp: Fixes issue with Configure Endpoint command
Patch adds flag EP_UNCONFIGURED to detect whether endpoint was
unconfigured. This flag is set in cdnsp_reset_device after Reset Device
command. Among others this command disables all non control endpoints.
Flag is used in cdnsp_gadget_ep_disable to protect controller against
invoking Configure Endpoint command on disabled endpoint. Lack of this
protection in some cases caused that Configure Endpoint command completed
with Context State Error code completion.

Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
2021-04-12 20:19:23 +08:00
Colin Ian King
9ecc3eb03c
usb: cdnsp: remove redundant initialization of variable ret
The variable ret is being initialized with a value that is
never read and it is being updated later with a new value.  The
initialization is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
2021-04-12 20:19:22 +08:00
Wang Qing
8079ebf5ff
usb: cdns3: delete repeated clear operations
dma_alloc_coherent already zeroes out memory, so memset is not needed.

Signed-off-by: Wang Qing <wangqing@vivo.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
2021-04-12 20:19:22 +08:00
Sanket Parmar
8430e98f2c
usb: cdns3: Optimize DMA request buffer allocation
dma_alloc_coherent() might fail on the platform with a small
DMA region.

To avoid such failure in cdns3_prepare_aligned_request_buf(),
dma_alloc_coherent() is replaced with dma_alloc_noncoherent()
to allocate aligned request buffer of dynamic length.

Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
2021-04-12 20:19:22 +08:00
Sanket Parmar
b9b1eae761
usb: cdns3: Use dma_pool_* api to alloc trb pool
Allocation of DMA coherent memory in atomic context using
dma_alloc_coherent() might fail on platforms with smaller
DMA region.

To fix it, dma_alloc_coherent() is replaced with dma_pool
API to allocate a smaller chunk of DMA coherent memory for
TRB rings.

Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
2021-04-12 20:19:22 +08:00
Frank Li
575dd7ece6
usb: cdns3: fix static checker warning.
The patch c450e48eb570: "usb: cdns3: add power lost support for
system resume" from Feb 18, 2021, leads to the following static
checker warning:

        drivers/usb/cdns3/core.c:551 cdns_resume()
        error: uninitialized symbol 'ret'.

drivers/usb/cdns3/core.c
544
545     if (!role_changed) {
546            if (cdns->role == USB_ROLE_HOST)
547                  ret = cdns_drd_host_on(cdns);
548     else if (cdns->role == USB_ROLE_DEVICE)
549            ret = cdns_drd_gadget_on(cdns);

"ret" is uninitialized at else branch.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
2021-04-12 20:19:21 +08:00
Wei Yongjun
ef32e0513a
usb: cdns3: imx: mark cdns_imx_system_resume as __maybe_unused
The function cdns_imx_system_resume() may have no callers depending
on configuration, so it must be marked __maybe_unused to avoid
harmless warning:

drivers/usb/cdns3/cdns3-imx.c:378:12: warning:
 'cdns_imx_system_resume' defined but not used [-Wunused-function]
  378 | static int cdns_imx_system_resume(struct device *dev)
      |            ^~~~~~~~~~~~~~~~~~~~~~

Fixes: 67982dfa59de ("usb: cdns3: imx: add power lost support for system resume")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
2021-04-12 20:19:21 +08:00
Peter Chen
39be23f4f1
usb: cdns3: trace: delete the trace parameter for request->trb
It is not correct using %pa to print virtual address of request->trb, and
it is hard to print its physical address due to the virtual address is
zero before using. It could use index (start_trb/end_trb) to know the
current trb position, so no matter virtual address or physical address
for request-trb is not so meaningful.

Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
2021-04-12 20:19:21 +08:00
Frank Li
2fd69eca06
usb: cdns3: imx: add power lost support for system resume
imx need special handle when controller lost power

Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
2021-04-12 20:19:21 +08:00
Frank Li
2cf2581cd2
usb: cdns3: add power lost support for system resume
If the controller lost its power during the system suspend, we need
to do all initialiation operations.

Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
2021-04-12 20:19:20 +08:00
Ye Bin
1d08ed588c usbip: vudc: fix missing unlock on error in usbip_sockfd_store()
Add the missing unlock before return from function usbip_sockfd_store()
in the error handling case.

Fixes: bd8b820422 ("usbip: vudc synchronize sysfs code paths")
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408112305.1022247-1-yebin10@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-12 10:29:50 +02:00
Greg Kroah-Hartman
14d34d2dbb Merge 5.12-rc7 into usb-next
We need the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-12 08:15:27 +02:00
Serge Semin
3db5337440 usb: dwc3: qcom: Detect DWC3 DT-nodes using compatible string
In accordance with the USB HCD/DRD schema all the USB controllers are
supposed to have DT-nodes named with prefix "^usb(@.*)?". Since the
existing DT-nodes will be renamed in a subsequent patch let's fix the DWC3
Qcom-specific code to detect the DWC3 sub-node just by checking its
compatible string to match the "snps,dwc3". The semantic of the code
won't change seeing all the DWC USB3 nodes are supposed to have the
compatible property with any of those strings set.

Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210409113029.7144-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-10 10:46:09 +02:00
Bixuan Cui
dc1e7e9a27 usb: dwc3: qcom: Remove redundant dev_err call in dwc3_qcom_probe()
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210410024818.65659-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-10 10:45:52 +02:00
Chunfeng Yun
90d28fb53d usb: core: reduce power-on-good delay time of root hub
Return the exactly delay time given by root hub descriptor,
this helps to reduce resume time etc.

Due to the root hub descriptor is usually provided by the host
controller driver, if there is compatibility for a root hub,
we can fix it easily without affect other root hub

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618017645-12259-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-10 10:45:48 +02:00
Longfang Liu
26b75952ca USB:ehci:fix Kunpeng920 ehci hardware problem
Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.

When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.

Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-10 10:45:38 +02:00
Johan Hovold
4969602741 USB: cdc-acm: fix TIOCGSERIAL implementation
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.

The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when it is
not used.

Similarly, baud_base could be used to set the UART base clock when it
could not be detected, but might as well be left unset when it is not
known (which is the case for CDC).

Fix the cdc-acm TIOCGSERIAL implementation by dropping its custom
interpretation of the unused xmit_fifo_size and baud_base fields, which
overflowed the former with the URB buffer size and set the latter to the
current line speed. Also return the port line number, which is the only
other value used besides the close parameters.

Note that the current line speed can still be retrieved through the
standard termios interfaces.

Fixes: 18c75720e6 ("USB: allow users to run setserial with cdc-acm")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:08:27 +02:00
Johan Hovold
dd5619582d USB: cdc-acm: fix unprivileged TIOCCSERIAL
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.

A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.

Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.

Fixes: ba2d8ce9db ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:08:27 +02:00
Johan Hovold
729f7955cb Revert "USB: cdc-acm: fix rounding error in TIOCSSERIAL"
This reverts commit b401f8c4f4.

The offending commit claimed that trying to set the values reported back
by TIOCGSERIAL as a regular user could result in an -EPERM error when HZ
is 250, but that was never the case.

With HZ=250, the default 0.5 second value of close_delay is converted to
125 jiffies when set and is converted back to 50 centiseconds by
TIOCGSERIAL as expected (not 12 cs as was claimed, even if that was the
case before an earlier fix).

Comparing the internal current and new jiffies values is just fine to
determine if the value is about to change so drop the bogus workaround
(which was also backported to stable).

For completeness: With different default values for these parameters or
with a HZ value not divisible by two, the lack of rounding when setting
the default values in tty_port_init() could result in an -EPERM being
returned, but this is hardly something we need to worry about.

Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:08:27 +02:00
Hans de Goede
55d8b34772 usb: typec: tcpm: Add support for altmodes
Add support for altmodes described in the usb-connector fwnode
associated with the Type-C controller by calling the new
typec_port_register_altmodes_from_fwnode() helper for this.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:07:42 +02:00
Hans de Goede
7b458a4c5d usb: typec: Add typec_port_register_altmodes()
This can be used by Type-C controller drivers which use a standard
usb-connector fwnode, with altmodes sub-node, to describe the available
altmodes.

Note there are is no devicetree bindings documentation for the altmodes
node, this is deliberate. ATM the fwnodes used to register the altmodes
are only used internally to pass platform info from a drivers/platform/x86
driver to the type-c subsystem.

When a devicetree user of this functionally comes up and the dt-bindings
have been hashed out the internal use can be adjusted to match the
dt-bindings.

Currently the typec_port_register_altmodes() function expects
an "altmodes" child fwnode on port->dev with this "altmodes" fwnode having
child fwnodes itself with each child containing 2 integer properties:

1. A "svid" property, which sets the id of the altmode, e.g. displayport
altmode has a svid of 0xff01.

2. A "vdo" property, typically used as a bitmask describing the
capabilities of the altmode, the bits in the vdo are specified in the
specification of the altmode.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:07:41 +02:00
Hans de Goede
3a2a91a2d5 usb: roles: Call try_module_get() from usb_role_switch_find_by_fwnode()
usb_role_switch_find_by_fwnode() returns a reference to the role-switch
which must be put by calling usb_role_switch_put().

usb_role_switch_put() calls module_put(sw->dev.parent->driver->owner),
add a matching try_module_get() to usb_role_switch_find_by_fwnode(),
making it behave the same as the other usb_role_switch functions
which return a reference.

This avoids a WARN_ON being hit at kernel/module.c:1158 due to the
module-refcount going below 0.

Fixes: c6919d5e0c ("usb: roles: Add usb_role_switch_find_by_fwnode()")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409124136.65591-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:07:03 +02:00
Manish Narani
124b11cc4f usb: dwc3: xilinx: Remove the extra freeing of clocks
The clocks are configured by devm_clk_bulk_get_all() in this driver. In
case of any error the clocks freeing will be handled automatically.
There is no need to explicitly free the clocks. Fix the same.

Fixes: 84770f028f ("usb: dwc3: Add driver for Xilinx platforms")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1617904448-74611-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:05:32 +02:00
Manish Narani
3a2a68ecb2 usb: dwc3: Resolve kernel-doc warning for Xilinx DWC3 driver
The kernel-doc run gave a warning for Xilinx DWC3 driver:

drivers/usb/dwc3/dwc3-xilinx.c:27: warning: expecting prototype for
dwc3(). Prototype was for XLNX_USB_PHY_RST_EN() instead

Basically it was due to an extra '*' in line:2. This patch fixes the same.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1617904448-74611-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:05:32 +02:00
Bixuan Cui
025f97d188 usb: core: hub: Fix PM reference leak in usb_port_resume()
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408130831.56239-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:03:25 +02:00
Bixuan Cui
9535b99533 usb: musb: fix PM reference leak in musb_irq_work()
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408091836.55227-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:02:44 +02:00
Yang Yingliang
a932ee40c2 usb: gadget: tegra-xudc: Fix possible use-after-free in tegra_xudc_remove()
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.

Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092947.3271507-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:02:33 +02:00
Zheng Yongjun
7c53624cbd usb: host: u132-hcd: use DEFINE_MUTEX() for mutex lock
mutex lock can be initialized automatically with DEFINE_MUTEX()
rather than explicitly calling mutex_init().

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20210405101434.14878-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:02:30 +02:00
Colin Ian King
9c2076090c usb: gadget: r8a66597: Add missing null check on return from platform_get_resource
The call to platform_get_resource can potentially return a NULL pointer
on failure, so add this check and return -EINVAL if it fails.

Fixes: c41442474a ("usb: gadget: R8A66597 peripheral controller support.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Dereference null return")
Link: https://lore.kernel.org/r/20210406184510.433497-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-09 16:02:26 +02:00