* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (66 commits)
avr32: at32ap700x: fix typo in DMA master configuration
dmaengine/dmatest: Pass timeout via module params
dma: let IMX_DMA depend on IMX_HAVE_DMA_V1 instead of an explicit list of SoCs
fsldma: make halt behave nicely on all supported controllers
fsldma: reduce locking during descriptor cleanup
fsldma: support async_tx dependencies and automatic unmapping
fsldma: fix controller lockups
fsldma: minor codingstyle and consistency fixes
fsldma: improve link descriptor debugging
fsldma: use channel name in printk output
fsldma: move related helper functions near each other
dmatest: fix automatic buffer unmap type
drivers, pch_dma: Fix warning when CONFIG_PM=n.
dmaengine/dw_dmac fix: use readl & writel instead of __raw_readl & __raw_writel
avr32: at32ap700x: Specify DMA Flow Controller, Src and Dst msize
dw_dmac: Setting Default Burst length for transfers as 16.
dw_dmac: Allow src/dst msize & flow controller to be configured at runtime
dw_dmac: Changing type of src_master and dest_master to u8.
dw_dmac: Pass Channel Priority from platform_data
dw_dmac: Pass Channel Allocation Order from platform_data
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: dw_mmc: support mmc power control with regulator
mmc: dw_mmc: fix suspend/resume operation
mmc: dw_mmc: add quirks for unreliable card detect, and capabilities
mmc: tmio: fix address in kunmap_atomic() calls
mmc: core: reset card voltage after power off
mmc: core: export function mmc_do_release_host()
mmc: sdio: remember new card RCA when redetecting card
mmc: dw_mmc: Remove set-but-unused variable.
mmc: sdhci-esdhc-imx: add card detect on custom GPIO for mx25/35
mmc: sdhci-esdhc: broken card detection is not a default quirk
mmc: sdhci-esdhc-imx: add write protect on custom GPIO on mx25/35
mmc: msm_sdcc: remove needless cache flush after dma_unmap_sg()
mmc: sh_mmcif: support aggressive clock gating
mmc: check if mmc cards < 2GB do sector addressing
mmc: core: comment on why sdio_reset is done at init time
mmc: dw_mmc: support DDR mode
mmc: via-sdmmc: Remove set-but-unused variable.
mmc: cb710: Return err value in cb710_wait_while_busy()
mmc: sdhci-pci: Remove set-but-unused variable.
mmc: mxs-mmc: add mmc host driver for i.MX23/28
...
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
This adds the mmc host driver for Freescale MXS-based SoC i.MX23/28.
The driver calls into mxs-dma via generic dmaengine api for both pio
and data transfer.
Thanks Chris Ball for the indentation patch.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Most likely, the LCD panel on mx28 platform will require a pixel
clock higher than ref_xtal_clk (24 MHz), so the patch initializes
the parent of lcdif clock as ref_pix_clk.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is to add pad control helper macro to make the code easy
to read. The need is being seen when adding pad definitions for
LCDIF which gets ~30 pads to define.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
changes since v2:
- use v3 and v4 for specifying the ip version instead of i.MX23/28.
This is a better namespace when future versions are added.
- rename mach/fb.h to mach/mxsfb.h
changes since v1:
- Add a LCDC_ prefix to the register names.
- use set/clear registers where appropriate
- protect call to mxsfb_disable_controller() in mxsfb_remove()
with a (host->enabled) as suggested by Lothar Wassmann
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-fbdev@vger.kernel.org
Based on code created by Lothar Waßmann, Sascha Hauer, Wolfram Sang and
me.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
It is used for example in the i2c driver which can be compiled modular.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This patch adds dma support for Freescale MXS-based SoC i.MX23/28,
including apbh-dma and apbx-dma.
* apbh-dma and apbx-dma are supported in the driver as two mxs-dma
instances.
* apbh-dma is different between mx23 and mx28, hardware version
register is used to differentiate.
* mxs-dma supports pio function besides data transfer. The driver
uses dma_data_direction DMA_NONE to identify the pio mode, and
steals sgl and sg_len to get pio words and numbers from clients.
* mxs dmaengine has some very specific features, like sense function
and the special NAND support (nand_lock, nand_wait4ready). These
are too specific to implemented in generic dmaengine driver.
* The driver refers to imx-sdma and only a single descriptor is
statically assigned to each channel.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is not strictly necessary but the right thing to do.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This fixes a small memory leak that was only hit in very unlikely error
paths.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
i.MX23 Reference Manaul starts auart index from 1 than 0. Changing
the index to start from 0 requires corresponding changes on base
address, irq, and iomux definitions, and will probably confuse people
who reads codes and hardware documents together.
This patch introduced the field 'hwid' to distinguish the driver id
and controller id. These two ids are different on mx23 while
identical on mx28.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX23 Reference Manual names auart irq differently from i.MX28.
This patch is to align the naming with mx28, so that some device
registration codes can be shared.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit b2878fa (ARM: mx28: update clock and device name for dual fec
support) added only the new lookups without removing the old one.
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Get rid of ## preprocessor construct where it only makes the
code harder to read.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This is a very initial pm support and basically does nothing.
With this pm support entry, drivers can start testing their own
pm functions.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes a machine hang after a gpio irq triggered.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
_CLK_SET_RATE does not only handle the cpu clock but also other
clocks, so do not hardcode the HW_CLKCTRL_CPU register.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
reg | (1 << clk->enable_shift) always evaluates to true. Switch it
to & which makes much more sense
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Read fec mac address from ocotp and save it into fec_platform_data
mac field for fec driver to use.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since commit
6d803ba (ARM: 6483/1: arm & sh: factorised duplicated clkdev.c)
platforms need to select CLKDEV_LOOKUP instead of COMMON_CLKDEV and need
to include <linux/clkdev.h>.
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The mxs duart is actually an amba-pl011 device. This commit changes
the duart device code to dynamically allocate amba-pl011 device,
so that drivers/serial/amba-pl011.c can be used on mxs.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Change device name from "fec" to "imx28-fec", so that fec driver
can distinguish mx28.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are 2 versions of the timrot on Freescale MXS-based SoCs.
The v1 on MX23 only gets 16 bits counter, while v2 on MX28
extends the counter to 32 bits.
The implementation uses two timers, one for clock_event and
another for clocksource. MX28 uses timrot 0 and 1, while MX23
uses 0 and 2.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- DEBUG_LL support, which is incompatible with multi-soc MXS image
because of different DUART base address on MX23 and MX28
- uncompress message support
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- The mxs wdog is implemented in RTC block.
- There is a generic software reset routine for most modules on mxs.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Add helper definition and function for MXS-based.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
