In this routine, kzalloc allocates a memory block. This allocation is
freed in the error paths, but not in the normal exit, thus the allocation
is leaked.
The kmemleak facility was used to find the leak.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Statistics' state-machine in bnx2x driver must be synced with various driver
flows, but its current locking scheme manages to be wasteful [using 2 locks +
additional local variable] and prone to race-conditions at the same time,
as the state-machine and 'action' are being accessed under different locks.
In addition, current 'safe exec' isn't in fact safe, since the only guarantee
it gives is that DMA transactions are over, but ramrods might still be running.
This patch cleans up said logic, leaving us with a single lock for the entire
flow and removing the possible races.
Changes from v2:
- Switched into mutex locking from semaphore locking.
- Release locks on error flows.
Changes from v1:
Failure to acquire lock fails flow instead of printing a warning and
allowing access to the critical section.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/netfilter/nf_tables_core.c
The nf_tables_core.c conflict was resolved using a conflict resolution
from Stephen Rothwell as a guide.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the interface is not used, power down the integrated GPHY during
suspend. Similarly to bcmgenet_open(), bcmgenet_resume() powers on the GPHY
prior to any UniMAC activity.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Power up the GPHY while we are bringing-up the network interface, and
conversely, upon bring down, power the GPHY down. In order to avoid
creating hardware hazards, make sure that the GPHY gets powered on
during bcmgenet_open() prior to the UniMAC being reset as the UniMAC may
start creating activity towards the GPHY if we reverse the steps.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the GPHY power down sequence by setting all power down bits, putting
the GPHY in reset, and finally cutting the 25Mhz reference clock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing a number of extra steps and delays to power-up the GPHY, update
the sequence to reflect the proper procedure here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for implementing the power down GPHY sequence, rename
bcmgenet_ephy_power_up to illustrate that it is not EPHY specific but
PHY agnostic, and add an "enable" argument.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CK25_DIS bit controls whether a 25Mhz clock is fed to the GPHY or
not, in preparation for powering down the integrated GPHY when relevant,
make sure we clear that bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bcmgenet_power_down() fails, we would want to propagate a return
value from bcmgenet_wol_power_down_cfg() to know about this.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=m6GG
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.1-20150323' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-03-23
this is a pull request of 6 patches for net-next/master.
A patch by Florian Westphal, converts the skb->destructor to use
sock_efree() instead of own destructor. Ahmed S. Darwish's patch
converts the kvaser_usb driver to use unregister_candev(). A patch by
me removes a return from a void function in the m_can driver. Yegor
Yefremov contributes a patch for combined rx/tx LED trigger support. A
sparse warning in the esd_usb2 driver was fixes by Thomas Körper. Ben
Dooks converts the at91_can driver to use endian agnostic IO accessors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter's static checker warned that in vxlan_stop we are checking
if 'vs' can be NULL while later we simply derreference it.
As after commit 56ef9c909b ("vxlan: Move socket initialization to
within rtnl scope") 'vs' just cannot be NULL in vxlan_stop() anymore, as
the interface won't go up if the socket initialization fails. So we are
good to just remove the check and make it consistent.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always use software checksumming, since the hardware does not have any
checksum offload support.
This significantly improves local TCP tx performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The start-of-frame and end-of-frame bits were accidentally swapped.
In the current code it does not make any difference, since they are
always used together.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change __raw accesors to endian agnostic versions to allow the driver
to work properly on big endian systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hnd field of the structs does not need to be __le32: the
device just returns the value without using it itself.
Signed-off-by: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add <ifname>-rxtx trigger, that will be activated both for tx
as rx events. This trigger mimics "activity" LED for Ethernet
devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use can-dev's unregister_candev() instead of directly calling
networking unregister_netdev(). While both are functionally
equivalent, unregister_candev() might do extra stuff in the
future than just calling networking layer unregistration code.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Making sure that the bus-off state gets passed to can_change_state().
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PCAN USB (pro) FD adapters with firmware versions > 2.x support the
switching between ISO (default) and non-ISO conform bitstreams on the CAN bus.
The setting for the 2.x firmware adapters can be modified with the 'ip' tool
from the iproute2 package (option: fd-non-iso [on|off]).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PUCAN_CMD_RX_FRAME_(ENABLE|DISABLE) command has extended its purpose
and was therefore renamed to PUCAN_CMD_SET_(EN|DIS)_OPTION.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
smatch detected the following issue:
drivers/net/can/usb/gs_usb.c:904 gs_usb_probe() error:
potential null dereference 'dev'. (kzalloc returns null)
Add a check for null return from kzalloc and return -ENOMEM
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
USB endpoint's wMaxPacketSize field is an le16 entity. Use
appropriate le16_to_cpu macros to maintain endian independence.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current driver code arbitrarily assumes a max outstanding tx
value of 16 parallel transmissions. Meanwhile, the device
firmware provides its actual maximum inside its reply to the
CMD_GET_SOFTWARE_INFO message.
Under heavy tx traffic, if the interleaved transmissions count
increases above the limit reported by firmware, the firmware
breaks up badly, reports a massive list of internal errors, and
the candump traces hardly matches the actual frames sent and
received.
On the other hand, in certain models, the firmware can support
up to 48 tx URBs instead of just 16, increasing the driver
throughput by two-fold and reducing the possibility of -ENOBUFs.
Thus dynamically set the driver's max tx URBs value according
to firmware replies.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Transmission of an AP beacon does not call the TX interrupt service routine,
which usually does the cleanup. Instead, cleanup is handled in a tasklet
completion routine. Unfortunately, this routine has a serious bug in that it does
not release the DMA mapping before it frees the skb, thus one IOMMU mapping is
leaked for each beacon. The test system failed with no free IOMMU mapping slots
approximately one hour after hostapd was used to start an AP.
This issue was reported and tested at https://github.com/lwfinger/rtlwifi_new/issues/30.
Reported-and-tested-by: Kevin Mullican <kevin@mullican.com>
Cc: Kevin Mullican <kevin@mullican.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
AIC needs to be registered only when BTCOEX is enabled.
This fixes the error reported by kbuild:
>> ERROR: "ar9003_hw_attach_aic_ops" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined!
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BCM43362 firmware falsely reports it is capable of providing
MBSS. As a result AP mode no longer works for this device. Therefor
disable MBSS in the driver for this chipset.
Cc: stable@vger.kernel.org # 3.19.y
Reported-by: Jorg Krause <jkrause@posteo.de>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NetCP 1.5 available on newer K2 SoCs such as K2E and K2L introduced 3
variants of the ethss subsystem, 9 port, 5 port and 2 port. These have
one host port towards the CPU and N external slave ports.
To customize the driver for these new ethss sub systems, multiple
compatibility strings are introduced. Currently some of parameters that
are different on different variants such as number of ALE ports, stats
modules and number of ports are defined through constants. These are now
changed to variables in gbe_priv data that get set based on the
compatibility string. This is required as there are no hardware
identification registers available to distinguish among the variants
of NetCP 1.5 ethss. However there is identification register available
to differentiate between NetCP 1.4 vs NetCP 1.5 and the same is made use
of in the code to differentiate them.
For more reading on the details of this peripheral, please refer to the
User Guide available at http://www.ti.com/lit/pdf/spruhz3
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following checkpatch error. It seems to have passed checkpatch
last time when original code was introduced.
ERROR: Macros with complex values should be enclosed in parentheses
#172: FILE: drivers/net/ethernet/ti/netcp_ethss.c:869:
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keystone netcp driver re-uses davinci mdio driver. So enable it
by default for keystone netcp driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethss has multiple modules within the sub system
- switch sub system
- sgmii
- mdio
- switch module
NetCP driver re-uses existing davinci mdio driver. It requires to
have its own register region to map the reg space. So restructure
the code to use separate reg region for the individual modules it
manages. Use range property to define register space of NetCP and
use reg property to define individual reg spaces. So MDIO will have
its own reg space to map. This is a pre-requisite to enable MDIO
driver for NetCP.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10G switch requires forward port number in the taginfo field,
where as it should be in packet_info field for necp 1.4 Ethss. So
fill this value correctly in the knav dma descriptor.
Also rename dma_psflags field in struct netcp_tx_pipe to switch_to_port
as it contain no flag, but the switch port number for forwarding the
packet. Add a flag to hold the new flag, SWITCH_TO_PORT_IN_TAGINFO which
will be set for 10G. This can also used in the future for other flags for
the tx_pipe.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Home routers based on ARM SoCs like BCM4708 also have bcma bus with core
supported by bgmac.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ARM SoCs with bgmac Ethernet hardware we don't have any normal PHY.
There is always a switch attached but it's not even controlled over MDIO
like in case of MIPS devices.
We need a fixed PHY to be able to send/receive packets from the switch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_carrier_off() first, since that will prevent the stack from
queuing more packets to this IF. This operation is fast, and should
behave much nicer when trying to bring down an interface under load.
Reported-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use netif_carrier_off() first, since that will prevent the stack from
queuing more packets to this IF. This operation is fast, and should
behave much nicer when trying to bring down an interface under load.
Reported-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to e1000e_write_protect_nvm_ich8lan() is no longer supported by HW.
Access to these registers causes a system freeze in A step hardware and is
ignored in B step hardware. This function must not be called in hardware
newer than LPT.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.
Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.
Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.
Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.
Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the napi_alloc_skb function to allocate an skb when running within
the softirq context to avoid calls to local_irq_save/restore.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx coalescing value is internally converted from usecs to a value
that the hardware can use. When reporting the Rx coalescing value, this
internal value is converted back to usecs. During the conversion from
and back to usecs some rounding occurs. So, for example, when setting an
Rx usec of 30, it will be reported as 29. Fix this reporting issue by
keeping the original usec value and using that during reporting.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx coalescing support in the driver was a software implementation
for something lacking in the hardware. Using hrtimers, the idea was to
trigger a timer interrupt after having queued a packet for transmit.
Unfortunately, as the timer value was lowered, the timer expired before
the hardware actually did the transmit and so it was racey and resulted
in unnecessary interrupts.
Remove the Tx coalescing support and hrtimer and replace with a Tx timer
that is used as a reclaim timer in case of inactivity.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supplies a value that indicates the DMA range that it
is capable of using. Use this value rather than hard-coding it in
the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new lighter weight memory barriers when working with the device
descriptors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify that the queues referred to in a message when the device is
brought up are hardware queues and not necessarily related to the
Linux network queues.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is no interrupt code that indicates auto-negotiation
has timed out. If the auto-negotiation has timed out then the start of
a new auto-negotiation will begin again with a new base page being
received. The state machine could be in a state that is not expecting
this interrupt code which results in an error during auto-negotiation.
Update the code to timestamp when the auto-negotiation starts. Should
another page received interrupt code occur before auto-negotiation has
completed but after the auto-negotiation timeout, then reset the state
machine to allow the auto-negotiation to continue.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the setting of the transceiver type when retrieving the device
settings using ethtool and instead set the transceiver type in the
phy_driver structure flags field. Change the transceiver type to be
internal, also.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ethtool being able to control what is advertised, the advertising
field is what should be used for priming the auto-negotiation registers
and for various other checks, instead of the supported field.
Also, move the initial setting of the supported and advertising fields
into the probe function so that they are not reset each time the device
is brought up, thus allowing the user to set as desired before bringing
the device up.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test robot noticed that we check the return of vxlan_igmp_join and leave
but inside them there was a path that it could be used initialized.
It's not really possible because those if() inside these igmp functions
would always match as we can't have sockets of other type in there, but
this way we keep the compiler happy.
Fixes: 56ef9c909b ("vxlan: Move socket initialization to within rtnl scope")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an EEH error occurs, the device/slot is disconnected. This condition
is more reliably detected (i.e., returns all ones) with an MMIO read rather
than a config read -- especially on power platforms.
Hence, this patch fixes EEH error detection by replacing config reads with
MMIO reads for reading the error registers. The error registers in
Skyhawk-R/BE2/BE3 are accessible both via the config space and the
PCICFG (BAR0) memory space.
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing this cmd for more than 8 EQs does not have the intended effect
even on BEx and Skyhawk-R.
This patch fixes this by issuing this cmd for upto 8 EQs at a time.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a PF does not restrict its VF interface from enabling vlan
promiscuous mode. This breaks vlan isolation when a vlan
(transparent tagging) is configured on a VF.
This patch fixes this problem by disabling the vlan promisc capability
for VFs.
Reported-by: Yoann Juet <veilletechno-irts@univ-nantes.fr>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the current netback, the bandwidth limiter's parameters are only
settable during vif setup time. This patch register a watch on them, and
thus makes them runtime changeable.
When the watch fires, the timer is reset. The timer's mutex is used for
fencing the change.
Cc: Anthony Liguori <aliguori@amazon.com>
Signed-off-by: Imre Palik <imrep@amazon.de>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With patch '960d6d08e39 "mwifiex: delay skb allocation for RX
until cmd53 over"' we no more pass skb parameter to MP aggregation setup
helper function. We instead pass length to be aggregated.
This patch fixes an issue where we were passing length parameter of NULL
skb to aggregation routine resulting into crash. We should instead pass
rx_len received from mp_regs.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are no known BCM4354 PCIe devices released so removing
support from the driver until proven otherwise.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently support was added for the BCM4345 SDIO chipset by
commit 9c51026509 ("brcmfmac: Add support for BCM4345 SDIO chipset")
however this was verified using a BCM43455 device, which is
a more recent revision of the chip. This patch assure that
older revisions are not probed as they would fail.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Syed Asifful Dayyan <syedd@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch added support for the BCM43430 802.11n SDIO chipset.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BCM4356 PCIe wireless device was added recently but overlooked
the fact that the MODULE_FIRMWARE() macros were missing for the
firmwares needed by this device.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO uses a thread to handle all communication with the device,
for this data is exchanged between threads. This data needs proper
memory barriers to make sure that data "exchange" is going correct.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several host controllers supporting runtime-pm are causing issues
with our sdio wireless cards because they disable the sdio interrupt
upon going into runtime suspend. This patch avoids that by doing
a pm_runtime_forbid() call during the probe. Tested with Sony Vaio
Duo 13 which uses sdhci-acpi host controller.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's clear from the indenting that curly braces were intended here.
Fixes: e35000ead4 ('mwifiex: preprocess packets from TX queue')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the USB Id to link the D-Link DWA 130 USB Wifi adapter
to the rt2830 driver.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Pieter Truter <ptruter@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast is not yet properly supported for all connection types;
actually, only non-secure AP is supported. For all other cases,
fall back to old "pseudo-DMS" approach. Namely, for:
- PBSS
- secure connection
When re-routing MCAST Rx->Tx on the AP, do not Tx back to the origin
of the frame
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dedicated vring for multicast frames; this vring allocated for
AP and PBSS (both P2P GO and client) configurations
For short frames, use MCS0; for long - MCS1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sync with the wmi definitions from the firmware team
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix checkpatch warning:
WARNING: Prefer ether_addr_copy() over memcpy() if the
Ethernet addresses are __aligned(2)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For the networking code and for hardware network accelerators,
it is better to have IP header 4*n aligned. On the other side,
DMA on Rx path require buffer to be aligned on 4*n as well.
Having 14 bytes of Ethernet header, these 2 alignment
requests are in contradiction.
To solve this, order hardware offload block to not remove
SNAP header. This adds extra 6 bytes between addresses and
ethertype, making it 20 bytes total. This way, both buffer and
IP header are 4*n aligned. Remaining is only to remove SNAP
by shifting addresses 6 bytes. This involves data copying, so
this feature should be disabled unless required by the platform.
Module parameter "rx_align_2" (bool, default - false)
introduced to control this feature. Feature is completely disabled
when parameter is false.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"echo" used to be called when no firmware loaded to the NIC,
this causes error output.
Probe firmware with "echo" only after it returned "ready" event.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use temporal variable for often used vring->swhead;
and use proper index in debug printing - vring->swhead
used before was modified in wil_vring_advance_head
and then increased value was used in debug print
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The cw1200 driver implements suspend and resume callbacks and assigns them
to the suspend and resume fields of the device_driver struct. These
callbacks are never actually called by anything though.
Modify the driver to properly use dev_pm_ops so that the suspend function
is actually executed upon suspend and drop the empty resume function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I've been getting this error when building mainline kernels using
Fedora's config files:
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c: In function ‘_rtl88ee_init_mac’:
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:853:2: error: implicit declaration of function ‘rtl_hal_pwrseqcmdparsing’ [-Werror=implicit-function-declaration]
if (!rtl_hal_pwrseqcmdparsing(rtlpriv, PWR_CUT_ALL_MSK,
^
cc1: some warnings being treated as errors
scripts/Makefile.build:258: recipe for target 'drivers/net/wireless/rtlwifi/rtl8188ee/hw.o' failed
I'm not sure if this is the correct fix, but it does seem to allow the
build to complete. I suspect that this was broken by commit 34ed780a6a
(rtlwifi: Fix problems with building an allyesconfig). Most of the files
that removed the include of pwrseqcmd.h, added one for ../pwrseqcmd.h.
The rtl8188ee driver had it removed it but didn't add the include of the
file in the parent directory.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a MCI reset is done, make sure that AIC
is started.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the main AIC calibration function to
handle MCI_STATE_AIC_CAL.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds a function to handle the
MCI message MCI_STATE_AIC_START.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a routine to handle the MCI_STATE_AIC_CAL_RESET
message.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since various MCI messages need to be
handled, along with driver-level support
in upper layers, disable AIC for now.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for post-processing
the AIC calibration results.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the appropriate bits in the HW after
AIC calibration is done.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds routines to handle the MCI
message AIC_CAL_SINGLE, starting the required
HW calibration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various registers to control and check AIC
status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AIC can be disabled or enabled on a per-card
basis using MCI configuration, so register a function
to check its status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are necessary for implementing AIC,
supported by chips like WB222.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Quit complaining about a couple of events that we actually expect to see
during an NVM update.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make PCI Device ID Tables be "const" to move them out of the data segment and
remove a redundant check on CH_PCI_DEVICE_ID_TABLE_DEFINE_BEGIN in
t4_pci_id_tbl.h to guard the contents of the include file.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-19
This wont the last 4.1 bluetooth-next pull request, but we've piled up
enough patches in less than a week that I wanted to save you from a
single huge "last-minute" pull somewhere closer to the merge window.
The main changes are:
- Simultaneous LE & BR/EDR discovery support for HW that can do it
- Complete LE OOB pairing support
- More fine-grained mgmt-command access control (normal user can now do
harmless read-only operations).
- Added RF power amplifier support in cc2520 ieee802154 driver
- Some cleanups/fixes in ieee802154 code
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware frequently manages to trigger this, and there's
no known driver workaround, so stop warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the driver callback returns that it's out of space for new
stations, the mac80211 IBSS code still keeps the station so it
doesn't try to add it over and over again.
Since the rate scaling algorithm is separate in mac80211, it also
invokes the rate scaling algorithm for such stations. It doesn't
know that our rate scaling algorithm is tightly integrated with
the MVM code and relies on those data structures, and it cannot
as the abstraction doesn't allow for it.
This leads to crashes when the rate scaling algorithm tries to
use uninitialized data, notably the mvmsta->vif pointer.
Protect against this in the rate scaling algorithm. We cannot get
good rates with such peers anyway since the firmware cannot do
anything with them.
This should fix https://bugzilla.kernel.org/show_bug.cgi?id=93461
CC: <stable@vger.kernel.org>
Reported-by: Richard Taylor <rjt-kernel@thegrindstone.me.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The assumption before this patch was that we don't need to
run again the INIT firmware after the system booted. The
INIT firmware runs calibrations which impact the physical
layer's behavior.
Users reported that it may be helpful to run these
calibrations again every time the interface is brought up.
The penatly is minimal, since the calibrations run fast.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=94341
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This reverts commit 11ad714b98 because
it breaks cx82310_eth.
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the phys_port_name operation. Port names are pulled from the
rocker hardware model in qemu and default to the qemu name + port id.
e.g.,
sw1p1: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:12:35:01 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
where 'sw1' comes from the qemu command line -device rocker,name=sw1, and
'p1' is port 1.
Patch is adapted from Scott's phys_port_id patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if a multicast join operation fail, the vxlan interface will
be UP but not functional, without even a log message informing the user.
Now that we can grab socket lock after already having rntl, we don't
need to defer socket creation and multicast operations. By not deferring
we can do proper error reporting to the user through ip exit code.
This patch thus removes all deferred work that vxlan had and put it back
inline. Now the socket will only be created, bound and join multicast
group when one bring the interface up, and will undo all that as soon as
one put the interface down.
As vxlan_sock_hold() is not used after this patch, it was removed too.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in favor of their inner __ ones, which doesn't grab rtnl.
As these functions need to operate on a locked socket, we can't be
grabbing rtnl by then. It's too late and doing so causes reversed
locking.
So this patch:
- move rtnl handling to callers instead while already fixing some
reversed locking situations, like on vxlan and ipvs code.
- renames __ ones to not have the __ mark:
__ip_mc_{join,leave}_group -> ip_mc_{join,leave}_group
__ipv6_sock_mc_{join,drop} -> ipv6_sock_mc_{join,drop}
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port statistics bitmap will now be initialized at port init. Even before
starting the port, statistics are visible to the user and must be properly masked.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.
Fixes: f8c6455bb0 ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_set_tx_maxrate support.
To support per tx queue maxrate limit, we use the update-qp firmware
command to do run-time rate setting for the qp that serves this tx ring.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the low-level device commands and definitions used for QP max-rate limiting.
This is done through the following elements:
- read rate-limit device caps in QUERY_DEV_CAP: number of different
rates and the min/max rates in Kbs/Mbs/Gbs units
- enhance the QP context struct to contain rate limit units and value
- allow to do run time rate-limit setting to QPs through the
update-qp firmware command
- QP rate-limiting is disallowed for VFs
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.
Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.
This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.
The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Storing the `platform_data` struct inside of the SPI struct when using
the device tree allows for a later function to edit the content of that
struct. This patch refactors the `cc2520_get_platformat_data` function
to accept a pointer to a `cc2520_platform_data` struct and populates
the fields inside of it.
This change mirrors commit aaa1c4d226
("at86rf230: copy pdata to driver allocated space").
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- Added resource initialization based on port-id field
- Enabled second SGMII 1G interface
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.
The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.
After the patch, this was supposed to be taken care of with :
irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix an issue when at86rf230_read_subreg was successful. The
function at86rf230_read_subreg will directly call regmap_read which
returns zero on successful. Nobody figured out issues yet because it was
only necessary to evaluate dvdd state while probing. This could make
trouble because the stack variable could have an random value.
The function is also used by reset the irq line before requesting irq, but
the value isn't evaluated afterwards.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This would fix randconfig compile error:
net/built-in.o: In function `netdev_switch_fib_ipv4_abort':
(.text+0xf7811): undefined reference to `fib_flush_external'
Also it fixes following warnings:
warning: (NET_DSA) selects NET_SWITCHDEV which has unmet direct dependencies (NET && INET)
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6131 && NET_DSA_MV88E6123_61_65 && NET_DSA_MV88E6171 && NET_DSA_MV88E6352 && NET_DSA_BCM_SF2) selects NET_DSA which has unmet direct dependencies (NET && HAVE_NET_DSA && NET_SWITCHDEV)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO controller on little endian Socs, e.g. ls2085a is similar to the
controller on big endian Socs, but the MDIO access is little endian,
we use I/O accessor function to handle endianness, so the driver can
run on little endian Socs. A property "little-endian" is used
in DTS to indicate the MDIO is little endian, if driver probes the
property, driver will access MDIO in little endian, otherwise, driver
works in big endian by default.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug in xgmac_wait_until_done() which mdio_stat should be used
instead of mdio_data when checking if busy bit is cleared.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hast to fix some sparse warning, I hard-coded a fix-sized array on the stack
which is probably too big for kernel standards. Fix this by converting array
to dynamic allocation.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves SKB allocation for RX packets from current
place i.e. after reading MP regs to place where we already
have read data from SDIO bus ie after cmd53.
mp_rx_aggr_setup has been modified accordingly to set
skb_arr to NULL.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch brings in support for SDIO single port rx aggregation
to mwifiex.
Maximum read size support by SDIO cmd53 is 64K.
Based on multi port aggregation which is already part of mwifiex, idea here
is multiple packets received in FW can be aggregated into single buffer.
A separate upload type is defined for such packet aggregated to single port.
Packets from this single buffer are later deaggregated into individual packets.
This way, driver can receive more packets each time through single SDIO cmd53;
thereby reducing no of times MMC bus is accessed.
SDIO SP aggregation support is advertised by FW during load time and driver
would get FW block size in command response of HostCmd_CMD_SDIO_SP_RX_AGGR_CFG.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During profiling, we discovered that driver remains idle for time
when pakcet is downloaded to FW but no TX_DONE has been received
i.e. while data_sent is true.
This patch adds enhancement to TX routine where we preprocess
packets from TX queue, make them ready for TX and add them to
separate TX queue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Chin-ran Lo <crlo@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch does away with spinlock in
mwifiex_wmm_get_highest_priolist_ptr in order to improve TP.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch removes BA setup helper routines
mwifiex_is_bastream_setup and mwifiex_is_amsdu_in_ampdu_allowed.
Current code will use two functions to check bastream setup and
amsdu in ampdu. This patch change these functions to flags, thus
avoiding redundant spin_lock check while dequeuing TX packets.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current code does not check whether main_work_queue or
rx_work_queue is running when preparing to do queue_work,
this code fix add check before calling queue_work, reducing
unnecessary queue_work switch.
This change instead sets more_task flag to ensure we run main_process
superloop once again.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SD8897 support buffers of 4K and 16 such ports can be accomodated.
So basically 64K buffer size in single aggregation is supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename this function to reflect its purpose correctly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A crash was detected while changing virtual interface type is in
progress. This was tracked to race condition in accessing bss_priority
table while change is in progress. This patch ensures that main_process
and rx_process works are locked while we change virtual interface.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In struct wl18xx_acx_rx_rate_stat, rx_frames_per_rates field is an
array, not a number. This means WL18XX_DEBUGFS_FWSTATS_FILE can't be
used to display this field in debugfs (it would display a pointer, not
the actual data). Use WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY instead.
This bug has been found by adding a __printf attribute to
wl1271_format_buffer. gcc complained about "format '%u' expects
argument of type 'unsigned int', but argument 5 has type 'u32 *'".
Fixes: c5d94169e8 ("wl18xx: use new fw stats structures")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I have here FRITZ!WLAN USB Stick N v2 / idVendor=057c, idProduct=8501
and every single of this requests ends up with:
|ieee80211 phy0: rt2x00usb_vendor_request: Error - Vendor Request 0x0c failed for offset 0x0000 with error -32
I was browsing the the vedor code and I haven't seen such request so I
remove it with this patch. If I wasn't look enough or if this error is
expected then please excuse :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2800usb_autorun_detect() blindly assumes assumes that it worked while
it could have failed. Check the error code here.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My understanding ist that rt2x00usb_register_read() is void and so the
reader is unaware of read errors and assumes that whatever was on the
stack as it was about to read.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We might be in interrupt context at few places. So replace
del_timer_sync() with del_timer(). This patch fixes a kernel
trace problem seen occasionally during our testing.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for auto ARP feature in mwifiex.
The device will respond to ARP requests from the network
with ARP response in suspended state without waking up the host.
This feature is enabled in the driver by default.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed Rx aggregated packets are always followed
by a single Rx packet. This patch improves our logic to add
that extra packet in next aggregation.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In HT40 modes, pulse events on primary and extension
channel are processed individually. If valid, a pulse
event will be fed into the detector
* for primary frequency, or
* for extension frequency (+/-20MHz based on HT40-mode)
* or both
With that, a 40MHz radar will result in two individual
radar events.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support HT40 DFS mode, a triggering detector must
reset only itself but not other detector lines.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TPC support has been observed to cause some tx power fluctuations on
some devices with at least AR934x and AR938x chips.
Disable it for now until the bugs have been found and fixed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sc->nbcnvifs tracks assigned beacon slots, not enabled beacons.
Therefore, it cannot be used to decide if cur_conf->enable_beacon (bool)
should be updated, or if beacons have been enabled already.
With the current code (depending on the order of calls), beacons often
do not get enabled in an AP+STA setup.
To fix tracking of enabled beacons, convert cur_conf->enable_beacon to a
bitmask of enabled beacon slots.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move swdev wrappers over to new swdev ops (from previous ndo ops). No
functional changes to the implementation.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
rocker: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
dsa: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Hardware Filter Block (HFB) so that incoming Rx traffic
can be matched and directed to desired Rx queues.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read*() to get arch endian consistent
property values. Do some refactoring in the process.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use conversion macros to correctly access the BE
fields of the Rx and Tx Frame Control Block on LE CPUs.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use conversion macros to correctly access the BE
fields of the Rx and Tx Buffer Descriptors on LE CPUs.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-03-13
This series contains updates to ixgbe and ixgbevf.
Don adds additional support for X550 MAC types, which require additional
steps around enabling and disabling Rx. Also cleans up variable type
inconsistency.
I provide a patch to allow relaxed ordering to be enabled on SPARC
architectures. Also cleans up ixgbevf whitespace and code comments to
align the driver with networking coding standard. Lastly cleaned up
uses of memcpy() where ether_addr_copy() could have been used.
Alex removes some dead code in the ixgbe cleanup patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
Here's another set of Bluetooth & ieee802154 patches intended for 4.1:
- Added support for QCA ROME chipset family in the btusb driver
- at86rf230 driver fixes & cleanups
- ieee802154 cleanups
- Refactoring of Bluetooth mgmt API to allow new users
- New setting for static Bluetooth address exposed to user space
- Refactoring of hci_dev flags to remove limit of 32
- Remove unnecessary fast-connectable setting usage restrictions
- Fix behavior to be consistent when trying to pair already paired device
- Service discovery corner-case fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These registers are also changed by transceiver and should be volatile
for right accessing via regmap debugfs.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a handling for calibration if we are 5 minutes in PLL
state. I first tried to implement the calibration functionality in
TX_ON state via register values CF_START and DCU_START, but this occurs
a one second delay at each calibration time.
An another solution to start a calibration is to switch from TRX_OFF
state into TX_ON, then a calibration is done automatically by
transceiver. This method will be used in this patch, after each transmit
of a frame we check with jiffies if the PLL is set 5 minutes without
doing a TRX_OFF->(TX_ON || RX_AACK_ON) or channel switch. The worst case
would be a transceiver in receiving mode only, but this is under normal
operation very unlikely.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Cc: Werner Almesberger <werner@almesberger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replace the state change timing relevant sleeps with
hrtimers. Currently the sleeps are done in the complete handler of
spi_async. The relation of doing the state change timing sleep with a
timer will get the sleep functionality out of spi_async complete handler
context.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch initialize xtal_trim value to zero. The xtal_trim property is
an optional device tree value. Currently if no xtal_trim property is
given the xtal_trim value can be contain random data, because it's a
stack variable. This patch init the xtal_trim value to zero which is
also the default value after reset for at86rf230 transceivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A number of tx queue wake-up events went missing due to the
outlined scenario below. Start state is a pool of 16 tx URBs,
active tx_urbs count = 15, with the netdev tx queue open.
CPU #1 [softirq] CPU #2 [softirq]
start_xmit() tx_acknowledge()
................ ................
atomic_inc(&tx_urbs);
if (atomic_read(&tx_urbs) >= 16) {
-->
atomic_dec(&tx_urbs);
netif_wake_queue();
return;
<--
netif_stop_queue();
}
At the end, the correct state expected is a 15 tx_urbs count
value with the tx queue state _open_. Due to the race, we get
the same tx_urbs value but with the tx queue state _stopped_.
The wake-up event is completely lost.
Thus avoid hand-rolled concurrency mechanisms and use a proper
lock for contexts and tx queue protection.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable the xilinx driver for ARM64.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the macro to copy the Ethernet address instead of memcpy().
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Fix the code comments to align with drivers/net/ code commenting style,
as well as whitespace issues. The whitespace issues resolve checkpatch
errors, like lines exceeding 80 chars (except for strings) and the use
of tabs where possible.
CC: <kernel-team@fb.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
This patch removes some dead code from the cleanup path for ixgbe.
Setting and clearing the flag doesn't do anything since all we are
doing is setting the flag, scheduling NAPI, clearing the flag and
then letting netpoll do the polling cleanup. As such it doesn't
make much sense to have it there.
This patch also removes one minor white-space error.
CC: <kernel-team@fb.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that relaxed ordering is not disabled when
on SPARC, where it helps with performance.
CC: <kernel-team@fb.com>
CC: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Correcting a mistake when I initial created this function. I should
have made this static since it is only referenced where the function
pointer is assigned.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Missed this when I created commit 6a14ee0cfb ("ixgbe: Add X550 support
function pointers"). Use a the __be* type to be consistent with how the
value is assigned.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For the X550 mac type we have to do additional steps around
enabling/disabling Rx. This patch will add a layer of indirection
around these support functions to enable this.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delay the update of the TDMA producer index unless this is the last SKB
in a batch, or the queue is already stopped. Move the check for whether
the queue should be stopped before the xmit_more check to avoid locking
the transmit queue in case there was a SKB submitted which has xmit_more
set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to have both bcmgenet_xmit_single() and
bcmgenet_xmit_frag() perform a free_bds decrement and a prod_index
increment by one. In case one of these functions fails to map a SKB or
fragment for transmit, we will return and exit bcmgenet_xmit() with an
error.
We can therefore safely use our local copy of nr_frags to know by how
much we should decrement the number of free buffers available, and by
how much the producer count must be incremented and do this in the tail
of bcmgenet_xmit().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bcmgenet_desc_rx() calls bcmgenet_rx_refill() at the end of
Rx packet processing loop, after the current Rx packet has already been
passed to napi_gro_receive(). However, bcmgenet_rx_refill() might fail
to allocate a new Rx skb, thus leaving a hole on the Rx queue where no
valid Rx buffer exists.
To eliminate this situation:
1. Rewrite bcmgenet_rx_refill() to retain the current Rx skb on the Rx
queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.
2. Modify bcmgenet_desc_rx() to call bcmgenet_rx_refill() at the top of
Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Tested-by: Jaedon Shin <jaedon.shin@gmail.com>--
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2b995f6398.
Панов Андрей reported the following regression:
"Commit 2b995f6398 in 4.0.0-rc3 introduces a
nasty bug in transmit, corrupting packets.
To reproduce:
$ dd if=/dev/zero of=zeros bs=1M count=20
$ md5sum -b zeros
8f4e33f3dc3e414ff94e5fb6905cba8c *zeros
This checksum is correct.
Copy file "zeros" to another host with NFS, and it gets corrupted, checksum is
changed.
File should be big, small amounts of transmit isn't affected.
I use an i.MX6 Quad board.
If this commit is reverted, all works fine."
Reported-by: Панов Андрей <rockford@yandex.ru>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit dfd8645ea1 wrongly assumes that VXLAN_VDI_MASK includes
eight lower order reserved bits of VNI field that are using for remote
checksum offload.
Right now, when VNI number greater then 0xffff, vxlan_udp_encap_recv()
will always return with 'bad_flag' error, reducing the usable vni range
from 0..16777215 to 0..65535. Also, it doesn't really check whether RCO
bits processed or not.
Fix it by adding new VNI mask which has all 32 bits of VNI field:
24 bits for id and 8 bits for other usage.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array index 'j' is used before limits check.
Suggest put limit check before index use.
Signed-off-by : <Ameenali023@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function isn't really related to any bus core. It touches PCI
device config registers only, so move it to the (PCI) host file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@
-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The watchdog timer is used to put the device in a low-power mode when
it is idle for some time. This timer is stopped during that mode and
should be restarted upon activity. This has been broken by commit
d4150fced0365 ("brcmfmac: Simplify watchdog sleep."). This patch
restores the behaviour as it was before that commit.
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware provides pointer to SDIO shared information at end of
RAM during firmware initialization. End of RAM is obviously determined
by the actual ram size, but part of that may be used for save&restore
memory. In that case another location in RAM will hold the pointer.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of hard-coded memory sizes it is possible to obtain that
information from the internal memory registers.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the brcmf_chip_attach() function responsible for putting the
device in a state where it is accessible for firmware download.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The functions brcmf_chip_[enter/exit]_download() are not exclusively
used for firmware download so rename these more appropriate.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of checking the cores in the chip only if CONFIG_BRCMDBG
is selected perform the check always and extend it with more sanity
checking.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing the ramsize from the brcmf_sdio structure to avoid
duplication. The information is available in brcmf_chip
structure.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pre-requisite to shrink size of ieee80211_tx_info which in turn is
needed to shrink skb->cb to 40 bytes again.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we want to shrink skb->cb then we'd have to see about
reducing struct ieee80211_tx_info, which gets embedded inside
skb->cb[].
It provides a scratch space to be used by wireless drivers.
ar5523 uses the maximum space available today (40 bytes), but it seems
we don't need this -- data->skb pointer seems to always point back to the
skb whose cb buffer the data structure resides, iow, given a pointer to the
embedded control buffer we can infer the skb address.
Tested-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the RTT registers need to be configured for all
valid chains irrespective of the runtime chainmask,
use the actual chainmask of the chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When assigning the initvals for PCIE sleep/awake
registers, check the configuration that has been
assigned to pll_pwrsave during initialization. Also,
display a warning if we don't have valid arrays.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cards based on AR9462/AR9565 support more PCIE
power save mechanisms, so register them correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the value in ah->config.pll_pwrsave to determine
which array needs to be loaded. Also, initialize
pll_pwrsave to 1 by default.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These will be used to handle chip-specific
power save configuration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For the AP, configuration may say not to bridge traffic between
wireless clients. This is conveyed from user space (ex: hostapd has
ap_isolate parameter) with NL80211_CMD_SET_BSS, to the driver's
cfg80211 ops method change_bss
Add support for this setting.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is for AP only. If Rx data frame targeted to one of associated clients,
transmit it back to the wireless media and don't deliver to the host.
For the multicast frames, deliver to both host and wireless media.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is expected that driver completes NAPI when less than
full budget is consumed.
Fulfill this requirement.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These changes add support for BCM4345 SDIO chipset.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Syed Asifful Dayyan <syedd@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Msgbuf is using a wait_event_timeout to wait for the response on
an ioctl. The wakeup routine uses waitqueue_active to see if
wait_event_timeout has been called. There is a chance that the
response arrives before wait_event_timeout is called, this
will result in situation that wait_event_timeout never gets
woken again and assumed result will be a timeout. This patch
removes that errornous situation by always setting the
ctl_completed var before checking for queue active.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO is using a "shared" variable to handoff ctl frames to DPC
and to see when they are done. In a timeout situation this can
lead to erroneous situation where DPC started to handle the ctl
frame while the timeout expired. This patch will fix this by
adding locking around the shared variable.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The watchdog thread is used to put the SDIO bus to sleep when the
system is idling. This patch simplifies the way it is determined
when sleep can be entered.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On removal of SDIO card both functions of card will be getting
a remove call. When the first is hanging in ctrl frame xmit then
the second will cause oops. This patch fixes the xmit ctrl
handling in case of serious errors and also limits the handling
for remove to function 1 only.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To prepare for reset ath5k should finish all asynchronous tasks. At
first, it disables the interrupt generation, then it waits for the
interrupt handler and tasklets completion, and then proceeds to the HW
configuration update. But it does not consider that the interrupt
handler or tasklet re-enables the interrupt generation. And we fall in a
situation when ath5k assumes that interrupts are disabled, but it is
not.
This can lead to different consequences, such as reception of the frame,
when we do not expect it. Under certain circumstances, this can lead to
the following warning:
WARNING: at ath5k/base.c:589 ath5k_tasklet_rx+0x318/0x6ec [ath5k]()
invalid hw_rix: 1a
[..]
Call Trace:
[<802656a8>] show_stack+0x48/0x70
[<802dd92c>] warn_slowpath_common+0x88/0xbc
[<802dd98c>] warn_slowpath_fmt+0x2c/0x38
[<81b51be8>] ath5k_tasklet_rx+0x318/0x6ec [ath5k]
[<8028ac64>] tasklet_action+0x8c/0xf0
[<80075804>] __do_softirq+0x180/0x32c
[<80196ce8>] irq_exit+0x54/0x70
[<80041848>] ret_from_irq+0x0/0x4
[<80182fdc>] ioread32+0x4/0xc
[<81b4c42c>] ath5k_hw_set_sleep_clock+0x2ec/0x474 [ath5k]
[<81b4cf28>] ath5k_hw_reset+0x50/0xeb8 [ath5k]
[<81b50900>] ath5k_reset+0xd4/0x310 [ath5k]
[<81b557e8>] ath5k_config+0x4c/0x104 [ath5k]
[<80d01770>] ieee80211_hw_config+0x2f4/0x35c [mac80211]
[<80d09aa8>] ieee80211_scan_work+0x2e4/0x414 [mac80211]
[<8022c3f4>] process_one_work+0x28c/0x400
[<802df8f8>] worker_thread+0x258/0x3c0
[<801b5710>] kthread+0xe0/0xec
[<800418a8>] ret_from_kernel_thread+0x14/0x1c
Fix this issue by adding a new status flag, which forbids to re-enable
the interrupt generation until the HW configuration is completed.
Note: previous patch, which reorders the Rx disable code helps to avoid
the above warning, but not fixes the root cause of unexpected frame
receiving.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath5k updates the channel pointer and after that it stops the Rx logic
and apply channel to HW. In case of channel switch, such sequence
creates a small window when a frame, which is received on the old
channel is considered as a frame received on the new one.
The most notable consequence of this situation occurs during the switch
from 2 GHz band (CCK+OFDM) to the 5GHz band (OFDM-only). Frame received
with CCK rate, e.g. beacon received at the 1mbps, causes the following
warning:
WARNING: at ath5k/base.c:589 ath5k_tasklet_rx+0x318/0x6ec [ath5k]()
invalid hw_rix: 1a
[..]
Call Trace:
[<802656a8>] show_stack+0x48/0x70
[<802dd92c>] warn_slowpath_common+0x88/0xbc
[<802dd98c>] warn_slowpath_fmt+0x2c/0x38
[<81b51be8>] ath5k_tasklet_rx+0x318/0x6ec [ath5k]
[<8028ac64>] tasklet_action+0x8c/0xf0
[<80075804>] __do_softirq+0x180/0x32c
[<80196ce8>] irq_exit+0x54/0x70
[<80041848>] ret_from_irq+0x0/0x4
[<80182fdc>] ioread32+0x4/0xc
[<81b4c42c>] ath5k_hw_set_sleep_clock+0x2ec/0x474 [ath5k]
[<81b4cf28>] ath5k_hw_reset+0x50/0xeb8 [ath5k]
[<81b50900>] ath5k_reset+0xd4/0x310 [ath5k]
[<81b557e8>] ath5k_config+0x4c/0x104 [ath5k]
[<80d01770>] ieee80211_hw_config+0x2f4/0x35c [mac80211]
[<80d09aa8>] ieee80211_scan_work+0x2e4/0x414 [mac80211]
[<8022c3f4>] process_one_work+0x28c/0x400
[<802df8f8>] worker_thread+0x258/0x3c0
[<801b5710>] kthread+0xe0/0xec
[<800418a8>] ret_from_kernel_thread+0x14/0x1c
The easiest way to reproduce this warning is to run scan with dualband
NIC in noisy environments, when the channel 11 runs multiple APs. In my
tests if the APs num >= 12, the warning appears in the first few
seconds of scanning.
In order to fix this, the Rx disable code moved to a higher level and
placed before the channel pointer update. This is also makes the code a
bit more symmetrical, since we disable and enable the Rx in the same
function.
In fact, at the pointer update time new frames should not appear,
because interrupt generation at this point should already be disabled.
The next patch should address this issue.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* 8000 device family work
* Update to the BT Coex firmware API
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=l2Ap
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-03-12' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Location Aware Regulatory was added by Arik
* 8000 device family work
* Update to the BT Coex firmware API
In the case of AF_INET s_addr was set to INADDR_ANY (0) which which both
symmetric with the AF_INET6 case, where s_addr is not set, and unnecessary
as udp_conf is zeroed out earlier in the same function.
I suspect this change does not have any run-time effect due to compiler
optimisations. But it does make the code a little easier on the/my eyes.
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY state machine (in drivers/net/phy/phy.c) will unconditionally
call phydev->adjust_link (macb_handle_link_change) when polling in the
PHY_CHANGELINK state. As currently written, macb always ends up
requesting a new tx_clk frequency in macb_handle_link_change. It is a
waste of time to request a new tx_clk frequency if the link state hasn't
changed, as the tx_clk will already be configured properly.
Let's only request a new tx_clk clock frequency when necessary.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Cc: Josh Cartwright <joshc@ni.com>
Cc: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't delete napi from hash list during module exit. This will
cause the following panic when doing module load and unload:
BUG: unable to handle kernel paging request at 0000004e00000075
IP: [<ffffffff816bd01b>] napi_hash_add+0x6b/0xf0
PGD 3c5d5067 PUD 0
Oops: 0000 [#1] SMP
...
Call Trace:
[<ffffffffa0a5bfb7>] init_vqs+0x107/0x490 [virtio_net]
[<ffffffffa0a5c9f2>] virtnet_probe+0x562/0x791815639d880be [virtio_net]
[<ffffffff8139e667>] virtio_dev_probe+0x137/0x200
[<ffffffff814c7f2a>] driver_probe_device+0x7a/0x250
[<ffffffff814c81d3>] __driver_attach+0x93/0xa0
[<ffffffff814c8140>] ? __device_attach+0x40/0x40
[<ffffffff814c6053>] bus_for_each_dev+0x63/0xa0
[<ffffffff814c7a79>] driver_attach+0x19/0x20
[<ffffffff814c76f0>] bus_add_driver+0x170/0x220
[<ffffffffa0a60000>] ? 0xffffffffa0a60000
[<ffffffff814c894f>] driver_register+0x5f/0xf0
[<ffffffff8139e41b>] register_virtio_driver+0x1b/0x30
[<ffffffffa0a60010>] virtio_net_driver_init+0x10/0x12 [virtio_net]
This patch fixes this by doing this in virtnet_free_queues(). And also
don't delete napi in virtnet_freeze() since it will call
virtnet_free_queues() which has already did this.
Fixes 91815639d8 ("virtio-net: rx busy polling support")
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value in iwl_mvm_get_wakeup_status() is a bit unclear in
that it's not obvious that we don't leak fw_status in some cases.
Use fw_status directly with ERR_PTR() and return only it, that way
the compiler has a chance of proving that it's uninitialized (if it
ever is due to new changes.)
Additionally, this removes a smatch warning since smatch couldn't
figure out that fw_status can't, in fact, leak here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When IWLWIFI_DEBUGFS is not set, we should not unlock the mutex after
calling iwl_mvm_query_wakeup_reasons(), because this function unlocks
it already. Move the goto out_iterate outside the #ifdef.
Change-Id: I13d86402aecf0eeec44b1abbe2b244fbc706a5eb
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
The code here is a little confusing, the iwl_mvm_te_check_disconnect()
will check that the interface is a station, but going into it after
already having processed the time even end for P2P seems strange at
first look.
Put a switch statement there to distinguish the interface types and
make this more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We previously enabled the smart FIFO (SF) in BSS only after
association.
This cause interrupt latency on P2P on certain devices.
Change the working model to enable the SF all the time and
play with the timeout values based on the association state.
This change was not tested on older firwmares, so make it
happen only on -13.ucode and up.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
More sub system IDs were introduced for the 8260 series.
Add the new sub system IDs so the cards can be recognized.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware was not using the new API, so we don't need to
differentiate between the different stages of this new API.
The main difference here is that most of the hard coded
values are not sent through the command anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The newer devices will enable a new register for this
(DEVICE_SET_NMI_8000B_REG), but the interrupt handler
isn't wired yet.
Keep the old register for now.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When a station goes to sleep, we can't transmit any frame
to it. This means that until that station will wake up, a
queue that is dedicated to this station won't progress at
all. Take this into account when monitoring stuck queues
and don't account for the time the station was asleep.
This allows to mask false positives where the queues are
stuck not because of a bug, but because of the station
being asleep.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows the op_mode to let the transport know that a
queue is currently frozen and that its timer should be
stopped.
When the queue is unfrozen, its timer should be set to
expire after the remainder of the timeout has elapsed.
This can be used when stations go to sleep. When a station
goes to sleep, the op_mode can freeze the timer so that the
queue will never be considered as stuck. When the station
wakes up, the queue will be unfrozen.
This is meant to avoid false positives that would happen if
a buggy station goes to sleep for a very long time. In case
we have a dedicated queue for this station (BA agreement)
and it goes to sleep for a very long time, the queue would
rightfully be stopped during all that time. In this case,
the stuck queue timer could fire and that would be a false
positive.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The Tx statistics weren't updated when using fixed rate for
debugging. Fix this as Tx statistics are useful in this use case.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
RTNL is not taken during CT-kill so regulatory APIs cannot be invoked.
That's fine, since the HW is only brought up to check the temperature
during CT-kill. We don't expect Tx or scanning.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When using IBSS, it's easily possible to exhaust the number
of available stations in the driver, so don't warn on it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we load the firmware for the 8000 B step device, it'll
verify its signature. In the current version of the
hardware, there can be a race between the WiFi firmware
being loaded and the Bluetooth firmware being loaded.
Check that WiFi is authenticated, if not, take ownership
on the authentication machine to make sure that the WiFi
firmware will be authenticated.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New sub system IDs were introduced for the 8260 series.
This patch adds them so new 8260 cards can be recognized.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Make the print a bit more readable.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the FW returns an invalid channels count in response to an MCC request,
make sure we don't reference invalid indices in the channels array.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When entering D0i3, the MVM mutex cannot be grabbed. This interferes
with the calculation of the number of connected TDLS stations during
the setup of the power cmd.
The goal is to disable power saving for all vifs while any TDLS station
is connected. For this purpose it is enough to keep the pm_enabled
member of all mvmvifs as false. An update of the power state already
occurs when a TDLS station is added/removed, so the values are correctly
updated.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New NVM versions in LnP platforms have the lar_enable bits in a different
offset.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We don't need to acquire MAC access for each access, it
makes much more sense to keep the MAC access. This speeds
up the Tx DMA stop flow significantly.
Moreover, if one channel can't be stopped, stop the others
but don't poll for them to avoid being stuck there for a
long time.
This solves a situation in which we were stuck in that flow
for way too long with a spinlock held which led to a kernel
panic.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In-order to recognize newer step of the device, the driver
must read the chip_version_id from the AUX bus MISC address
space. This will determine what firmware file will be
loaded.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we associate we always need to update the quotas. This
fixes a bug for cases in which quotas weren't udapted after
association.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When moving to the D3 FW give it the valid MCC from the D0 FW. When
returning from D3 to D0, query the D3 FW for the latest MCC, as
it might have changed internally. This MCC will be replayed to the D0 FW
when it boots.
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When booting the card, check for a dedicated regulatory ACPI entry. If
such exists, read it and give the information to FW with the appropriate
source.
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For some configurations, the driver should get the MAC
address from the hardware registers and not from the
regular locations. Since the parsing of the MAC address
is the same regardless of its source, continue the regular
code path (parsing) after we read the registers.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This module parameter is useful for debugging NVM and LAR related issues.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
