Log the unrecognized error report type value as well.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW has been modified to send a new async event when it detects
a pause storm. Register for this new event and log it upon receipt.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add config_init for LAN8814. This function is required for the following
reasons:
- we need to make sure that the PHY is reset,
- disable ANEG with QSGMII PCS Host side
- swap the MDI-X A,B transmit so that there will not be any link flip-flaps
when the PHY gets a link.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the possessive "its" instead of the contraction of "it is" ("it's")
in user messages.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHER_CLK_SEL_FREQ_SEL_2P5M is not 0 bit of the register. This is a
value, which is 0. Fix from BIT(0) to 0.
Reported-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Fixes: b38dd98ff8 ("net: stmmac: Add Toshiba Visconti SoCs glue driver")
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://lore.kernel.org/r/20211223073633.101306-1-nobuhiro1.iwamatsu@toshiba.co.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hayes Wang says:
====================
r8152: fix bugs
Patch #1 fix the issue of force speed mode for RTL8156.
Patch #2 fix the issue of unexpected ocp_base.
====================
Link: https://lore.kernel.org/r/20211223092702.23841-386-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are some chances that the actual base of hardware is different
from the value recorded by driver, so we have to reset the variable
of ocp_base to sync it.
Set ocp_base to -1. Then, it would be updated and the new base would be
set to the hardware next time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It needs to set mdio force mode. Otherwise, link off always occurs when
setting force speed.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 561d835281 ("bridge: use ndo_siocdevprivate") changed the
source and destination arguments of copy_{to,from}_user in bridge's
old_deviceless() from args[1] to uarg breaking SIOC{G,S}IFBR ioctls.
Commit cbd7ad29a5 ("net: bridge: fix ioctl old_deviceless bridge
argument") fixed only BRCTL_{ADD,DEL}_BRIDGES commands leaving
BRCTL_GET_BRIDGES one untouched.
The fixes BRCTL_GET_BRIDGES as well and has been tested with busybox's
brctl.
Example of broken brctl:
$ brctl show
bridge name bridge id STP enabled interfaces
brctl: can't get bridge name for index 0: No such device or address
Example of fixed brctl:
$ brctl show
bridge name bridge id STP enabled interfaces
br0 8000.000000000000 no
Fixes: 561d835281 ("bridge: use ndo_siocdevprivate")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/all/20211223153139.7661-2-repk@triplefau.lt/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert the u32 variable to type u64 in a context where expression of
type u64 is required to avoid potential overflow.
Fixes: e9e3720002 ("net: stmmac: ptp: update tas basetime after ptp adjust")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://lore.kernel.org/r/20211223073928.37371-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For Ocelot switches, the CPU injected frames have an injection header
where it can specify the QoS class of the packet and the DSA tag, now it
uses the SKB priority to set that. If a traffic class to priority
mapping is configured on the netdevice (with mqprio for example ...), it
won't be considered for CPU injected headers. This patch make the QoS
class aligned to the priority to traffic class mapping if it exists.
Fixes: 8dce89aa5f ("net: dsa: ocelot: add tagger for Ocelot/Felix switches")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Marouen Ghodhbane <marouen.ghodhbane@nxp.com>
Link: https://lore.kernel.org/r/20211223072211.33130-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmHEgv4RHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt7jQf/W1J8lkaMw6mYnr+inmwKaP11VIk765Sf
4FXZl4xks5rs5zJOs61c/zInNIbu7QVsJzQLmM/bhTB1zoZMRo6ugXXrZ/LPMT1u
X0mul1rC+NLZLlgaimNXRZUXJ2tGUsYYhGoZLHbcILx7XF7/9WtE4h7tLviLdMYk
l42yjjP6s/I/zQHrLQdA9/puGl7g8CItbwaNZg6+PjgbS9NPGATrw9UZdOWjPcl4
JLMRHVgKtdlYL/U/IvsYg6o3Vbo0r+KEI2IMg5fOSpNwqbeQRIN4cZG4TDeRDqD/
k4/ZiFYlNdfVeWmZxHyqX6D3sroIquKglyah34fjzsJ2TbJC1zMvjw==
=VHFz
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
* tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (148 commits)
mt76: mt7921: fix a possible race enabling/disabling runtime-pm
wilc1000: Document enable-gpios and reset-gpios properties
wilc1000: Add reset/enable GPIO support to SPI driver
wilc1000: Convert static "chipid" variable to device-local variable
rtw89: 8852a: correct bit definition of dfs_en
rtw88: don't consider deep PS mode when transmitting packet
ath11k: Fix unexpected return buffer manager error for QCA6390
ath11k: add support of firmware logging for WCN6855
ath11k: Fix napi related hang
ath10k: replace strlcpy with strscpy
rtw88: support SAR via kernel common API
rtw88: 8822c: add ieee80211_ops::hw_scan
iwlwifi: mei: wait before mapping the shared area
iwlwifi: mei: clear the ownership when the driver goes down
iwlwifi: yoyo: fix issue with new DBGI_SRAM region read.
iwlwifi: fw: fix some scan kernel-doc
iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ
iwlwifi: mvm: remove card state notification code
iwlwifi: mvm: drop too short packets silently
iwlwifi: mvm: fix AUX ROC removal
...
====================
Link: https://lore.kernel.org/r/20211223141108.78808C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen says:
====================
mlxsw: Add tests for VxLAN with IPv6 underlay
mlxsw driver lately added support for VxLAN with IPv6 underlay.
This set adds tests for IPv6, which are dedicated for mlxsw.
Patch set overview:
Patches #1-#2 make vxlan.sh test more flexible and extend it for IPv6
Patches #3-#4 make vxlan_fdb_veto.sh test more flexible and extend it
for IPv6
Patches #5-#6 add tests for VxLAN flooding for different ASICs
Patches #7-#8 add test for VxLAN related traps and align the existing
test
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the case that sends packets with "too short inner packet" to
include part of ethernet header, to make the trap to be triggered due to
the correct reason.
According to ASIC arch, the trap is triggered if overlay packet length is
less than 18B, and the minimum inner packet should include source MAC and
destination MAC.
Till now the case passed because one of the reserved bits in VxLAN
header was used. This issue was found while adding an equivalent test
for IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test configures VxLAN with IPv6 underlay and verifies that the
expected traps are triggered under the right conditions.
The test is similar to the existing IPv4 test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.
The number of records is changed according to ASIC type and address
family.
Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-2 and above, which support up to four
IPv6 addresses in one record.
The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.
The number of records is changed according to ASIC type and address
family.
Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-1 switches, which support up to five
IPv6 addresses in one record.
The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test to verify FDB vetos of VxLAN with IPv6 underlay.
Use the existing test which checks IPv4.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan_fdb_veto.sh cases are dedicated to test VxLAN with IPv4 underlay.
The main changes to test IPv6 underlay are IP addresses and some flags.
Add variables to define all the values which supposed to be different
for IPv6 testing, set them to use the existing values by default.
The next patch will define the new added variables in a separated file,
so the same tests can be used for IPv6 also.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test to verify configuration of VxLAN with IPv6 underlay.
Use the existing test which checks IPv4.
Add separated test cases for learning which is not supported for IPv6
and for UDP checksum flags which are different from IPv4 flags.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan.sh cases are dedicated to test VxLAN with IPv4 underlay.
The main changes to test IPv6 underlay are IP addresses and some flags.
Add variables to define all the values which supposed to be different
for IPv6 testing, set them to use the existing values by default.
The next patch will define the new added variables in a separated file,
so the same tests can be used for IPv6 also.
Rename some functions to include "ipv4", so the next patch will add
equivalent functions for IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.
Replace kernel.h inclusion with the list of what is really being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series extends the current supported bridge flags with the
following flags: BR_FLOOD, BR_BCAST_FLOOD and BR_LEARNING.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct sctp_ep_common is included in both asoc and ep, but hlist_node
and hashent are only needed by ep after asoc_hashtable was dropped by
Commit b5eff71283 ("sctp: drop the old assoc hashtable of sctp").
So it is better to move hlist_node and hashent from sctp_ep_common to
sctp_endpoint, and it saves some space for each asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen says:
====================
Add tests for VxLAN with IPv6 underlay
mlxsw driver lately added support for VxLAN with IPv6 underlay.
This set adds the relevant tests for IPv6, most of them are same to
IPv4 tests with the required changes.
Patch set overview:
Patch #1 relaxes requirements for offloading TC filters that
match on 802.1q fields. The following selftests make use of these
newly-relaxed filters.
Patch #2 adds preparation as part of selftests API, which will be used
later.
Patches #3-#4 add tests for VxLAN with bridge aware and unaware.
Patche #5 cleans unused function.
Patches #6-#7 add tests for VxLAN symmetric and asymmetric.
Patch #8 adds test for Q-in-VNI.
====================
Link: https://lore.kernel.org/r/20211221144949.2527545-1-amcohen@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add test to check Q-in-VNI traffic with IPv6 underlay and overlay.
The test is similar to the existing IPv4 test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a similar fashion to the asymmetric test, add a test for symmetric
routing. In symmetric routing both the ingress and egress VTEPs perform
routing in the overlay network into / from the VxLAN tunnel. Packets in
different directions use the same VNI - the L3 VNI.
Different tenants (VRFs) use different L3 VNIs.
Add a test which is similar to the existing IPv4 test to check IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In asymmetric routing the ingress VTEP routes the packet into the
correct VxLAN tunnel, whereas the egress VTEP only bridges the packet to
the correct host. Therefore, packets in different directions use
different VNIs - the target VNI.
Add a test which is similar to the existing IPv4 test to check IPv6.
The test uses a simple topology with two VTEPs and two VNIs and verifies
that ping passes between hosts (local / remote) in the same VLAN (VNI)
and in different VLANs belonging to the same tenant (VRF).
While the test does not check VM mobility, it does configure an anycast
gateway using a macvlan device on both VTEPs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove `vxlan_ping_test()` which is not used and probably was copied
mistakenly from vxlan_bridge_1d.sh.
This was found while adding an equivalent test for IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tests are very similar to their VLAN-unaware counterpart
(vxlan_bridge_1d_ipv6.sh and vxlan_bridge_1d_port_8472_ipv6.sh),
but instead of using multiple VLAN-unaware bridges, a single VLAN-aware
bridge is used with multiple VLANs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add tests similar to vxlan_bridge_1d.sh and vxlan_bridge_1d_port_8472.sh.
The tests set up a topology with three VxLAN endpoints: one
"local", possibly offloaded, and two "remote", formed using veth pairs
and likely purely software bridges. The "local" endpoint is connected to
host systems by a VLAN-unaware bridge.
Since VxLAN tunnels must be unique per namespace, each of the "remote"
endpoints is in its own namespace. H3 forms the bridge between the three
domains.
Send IPv4 packets and IPv6 packets with IPv6 underlay.
Use `TC_FLAG`, which is defined in `forwarding.config` file, for TC
checks. `TC_FLAG` allows testing that on HW datapath, the traffic
actually goes through HW.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently `ping_do()` and `ping6_do()` send 10 packets.
There are cases that it is not possible to catch only the interesting
packets using tc rule, so then, it is possible to send many packets and
verify that at least this amount of packets hit the rule.
Add `PING_COUNT` variable, which is set to 10 by default, to allow tests
sending more than 10 packets using the existing ping API.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Spectrum ASICs do not support matching of VLAN ID at egress.
Currently, mlxsw driver forbids matching of all VLAN related fields at
egress, which is too strict check.
For example, the following filter is not supported by the driver:
$ tc filter add dev swpX egress protocol 802.1q pref 1 handle 101 flower
vlan_ethtype ipv4 src_ip .. dst_ip .. skip_sw action pass
Error: mlxsw_spectrum: vlan_id key is not supported on egress.
We have an error talking to the kernel
The filter above does not match on VLAN ID, but is bounced anyway.
Make the check more specific, forbid only matching of 'vlan_id' at egress.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1) From Shay Drory: Devlink user knobs to control device's EQ size
This series provides knobs which will enable users to
minimize memory consumption of mlx5 Functions (PF/VF/SF).
mlx5 exposes two new generic devlink params for EQ size
configuration and uses devlink generic param max_macs.
LINK: https://lore.kernel.org/netdev/20211208141722.13646-1-shayd@nvidia.com/
2) From Tariq and Lama, allocate software channel objects and statistics
of a mlx5 netdevice private data dynamically upon first demand to save on
memory.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmHClsoACgkQSD+KveBX
+j5d6gf+NKH8mQd6Aa/Gt4Y2DtS7GzN+dPD+2MokuT2YSWU8kVGlMnC01MTE2V2s
jiOUC6ZEbayx2ORzd58XlcfAMEZz2WH8VGLXTdmM3niv13D7AueSsUP5SVK7Oamk
h0bwzOV8CE1Ru5s3Q3zPaLBqTWN+TmyG42HNwYyD8GZT7O5q8iBfor97N2KN5U5u
rhxzFcD2jfhtYxACkjea6RTN9CTM7l9FS4+DIjhu53PAOBaOZLj8NKSYUqP6I17L
ITJDd9za4Nq/YiB2yU4UVNkDEXsuXWoqnTNsL1oEUPForEomJsnikHV9ywzyKVMn
SbWdZOr5C14UBH9wyyauEBBv5oLB7w==
=cotW
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-12-21
1) From Shay Drory: Devlink user knobs to control device's EQ size
This series provides knobs which will enable users to
minimize memory consumption of mlx5 Functions (PF/VF/SF).
mlx5 exposes two new generic devlink params for EQ size
configuration and uses devlink generic param max_macs.
LINK: https://lore.kernel.org/netdev/20211208141722.13646-1-shayd@nvidia.com/
2) From Tariq and Lama, allocate software channel objects and statistics
of a mlx5 netdevice private data dynamically upon first demand to save on
memory.
* tag 'mlx5-updates-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Take packet_merge params directly from the RX res struct
net/mlx5e: Allocate per-channel stats dynamically at first usage
net/mlx5e: Use dynamic per-channel allocations in stats
net/mlx5e: Allow profile-specific limitation on max num of channels
net/mlx5e: Save memory by using dynamic allocation in netdev priv
net/mlx5e: Add profile indications for PTP and QOS HTB features
net/mlx5e: Use bitmap field for profile features
net/mlx5: Remove the repeated declaration
net/mlx5: Let user configure max_macs generic param
devlink: Clarifies max_macs generic devlink param
net/mlx5: Let user configure event_eq_size param
devlink: Add new "event_eq_size" generic device param
net/mlx5: Let user configure io_eq_size param
devlink: Add new "io_eq_size" generic device param
====================
Link: https://lore.kernel.org/r/20211222031604.14540-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d068ca2ae2 ("codel: split into multiple files") moved all
Qdisc-related code to codel_qdisc.h, move the include of pkt_sched.h
as well.
This is similar to the previous commit, although we don't care as
much about incremental builds after pkt_sched.h was touched itself
it is included by net/sch_generic.h which is modified ~20 times
a year.
This decreases the incremental build size after touching pkt_sched.h
from 1592 to 617 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since sock.h is modified relatively often (60 times in the last
12 months) it seems worthwhile to decrease the incremental build
work.
CoDel's header includes net/inet_ecn.h which in turn includes net/sock.h.
codel.h is itself included by mac80211 which is included by much of
the WiFi stack and drivers. Removing the net/inet_ecn.h include from
CoDel breaks the dependecy between WiFi and sock.h.
Commit d068ca2ae2 ("codel: split into multiple files") moved all
the code which actually needs ECN helpers out to net/codel_impl.h,
the include can be moved there as well.
This decreases the incremental build size after touching sock.h
from 4999 objects to 4051 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable bytes is being used to summate slot lengths,
however the value is never used afterwards. The summation
is redundant so remove variable bytes.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211222003937.727325-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix an odd indent where some code was left indented, and causes smatch
to warn:
ice_log_pkg_init() warn: inconsistent indenting
While here, for consistency, add a break after the default case.
This commit has a Fixes: but we caught this while it was only in net-next.
Fixes: 247dd97d71 ("ice: Refactor status flow for DDP load")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20211221230538.2546315-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If asix_read_cmd() returns 0 on 30th interation, 0 will be returned from
asix_check_host_enable(), which is logically wrong. Fix it by returning
-ETIMEDOUT explicitly if we have exceeded 30 iterations
Also, replaced 30 with #define as suggested by Andrew
Fixes: a786e3195d ("net: asix: fix uninit value bugs")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ecd3470ce6c2d5697ac635d0d3b14a47defb4acb.1640117288.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
asix_read_cmd() may read less than sizeof(smsr) bytes and in this case
smsr will be uninitialized.
Fail log:
BUG: KMSAN: uninit-value in asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline]
BUG: KMSAN: uninit-value in asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] drivers/net/usb/asix_common.c:497
BUG: KMSAN: uninit-value in asix_mdio_read+0x3c1/0xb00 drivers/net/usb/asix_common.c:497 drivers/net/usb/asix_common.c:497
asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline]
asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] drivers/net/usb/asix_common.c:497
asix_mdio_read+0x3c1/0xb00 drivers/net/usb/asix_common.c:497 drivers/net/usb/asix_common.c:497
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Reported-and-tested-by: syzbot+f44badb06036334e867a@syzkaller.appspotmail.com
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/8966e3b514edf39857dd93603fc79ec02e000a75.1640117288.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-12-21
This series contains updates to ice driver only.
Karol modifies the reset flow to correct issues with PTP reset.
Jake extends PTP support for E822 based devices. This includes a few
cleanup patches, that fix some minor issues. In addition, there are some
slight refactors to ease the addition of E822 support, followed by adding
the new hardware implementation ice_ptp_hw.c.
There are a few major differences with E822 support compared to E810
support:
*) The E822 device has a Clock Generation Unit which must be initialized in
order to generate proper clock frequencies on the output that drives the PTP
hardware clock registers
*) The E822 PHY is a bit different and requires a more complex
initialization procedure which must be rerun any time the link configuration
changes.
*) The E822 devices support enhanced timestamp calibration by making use of
a process called Vernier offset measurement. This allows the hardware to
measure phase offset related to the PHY clocks for Serdes and FEC, reducing
the inaccuracy of the timestamp relative to the actual packet transmission
and receipt. Making use of this requires data gathered from the first
transmitted and received packets, and waiting for the PHY to complete the
calibration measurements. This is done as part of a new kthread, ov_work.
Note that to avoid delay in enabling timestamps, we start the PHY in
'bypass' mode which allows timestamps to be captured without the Vernier
calibration measurement. Once the first packets have been sent and received,
we then complete the calibration setup and exit bypass mode and begin using
the more precise timestamps. According to the datasheet, timestamps without
calibration data can be incorrect relative to actual receipt or transmission
by up to 1 clock cycle (~1.25 nanoseconds), while calibrated timestamps
should be correct to within 1/8th of a clock cycle (~0.15 nanoseconds).
*) E822 devices support crosstimestamping via PCIe PTM, which we enable when
available on the platform.
There is a fair amount of logic required to perform PHY and CGU
initialization, which is the vast majority of the new code, but it is fairly
self contained within ice_ptp_hw.c, with the exception of monitoring for
offset validity being handled by a kthread.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: support crosstimestamping on E822 devices if supported
ice: exit bypass mode once hardware finishes timestamp calibration
ice: ensure the hardware Clock Generation Unit is configured
ice: implement basic E822 PTP support
ice: convert clk_freq capability into time_ref
ice: introduce ice_ptp_init_phc function
ice: use 'int err' instead of 'int status' in ice_ptp_hw.c
ice: PTP: move setting of tstamp_config
ice: introduce ice_base_incval function
ice: Fix E810 PTP reset flow
====================
Link: https://lore.kernel.org/r/20211221174845.3063640-1-anthony.l.nguyen@intel.com
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because of the possible failure of the kcalloc, it should be better to
set rx_queue->page_ptr_mask to 0 when it happens in order to maintain
the consistency.
Fixes: 5a6681e22c ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20211220140344.978408-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because of the possible failure of the kcalloc, it should be better to
set rx_queue->page_ptr_mask to 0 when it happens in order to maintain
the consistency.
Fixes: 5a6681e22c ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20211220135603.954944-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a possible race enabling/disabling runtime-pm between
mt7921_pm_set() and mt7921_poll_rx() since mt7921_pm_wake_work()
always schedules rx-napi callback and it will trigger
mt7921_pm_power_save_work routine putting chip to in low-power state
during mt7921_pm_set processing.
Suggested-by: Deren Wu <deren.wu@mediatek.com>
Tested-by: Deren Wu <deren.wu@mediatek.com>
Fixes: 1d8efc741d ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/0f3e075a2033dc05f09dab4059e5be8cbdccc239.1640094847.git.lorenzo@kernel.org
Add documentation for the ENABLE and RESET GPIOs that may be needed by
wilc1000-spi.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221212531.4011609-3-davidm@egauge.net
