Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-06-26
This series contains fixes for igb, e1000e and i40evf.
Todd disables IPv6 extension header processing due to a hardware errata
and bumps the driver version.
Yanir provides six fixes for e1000e. First is a fix for a locking issue
where we were not always taking the pci_bus_sem semaphore all the time
when calling pci_disable_link_state_locked(), so fix the code to only call
pci_disable_link_state_locked() when the semaphore has been acquired,
otherwise call pci_disable_link_state(). A previous fix for i219 where
the hardware prevented ULP entry caused EEE in Sx not the be enabled, so
modify the code flow that allows both ULP and EEE in Sx. Fix an issue
when running 10/100 full duplex on i219 where CRC errors were occurring
by increasing the IPG from 8 to 0xC as per the hardware developers.
Fix a data corruption issue found on some platforms by increasing the
minimum gap between the PHY FIFO read and write pointers. Fix i219,
which does not require the K1 workaround for LPT devices.
Mitch provides a i40evf fix for a panic when changing MTU. Down was
requesting queue disables, but then exited immediately without waiting
for the queues to actually be disabled. This could allow any function
called after i40evf_down() to run immediately, including i40evf_up(),
and causes a memory leak. Fixed the issue by removing the whole
reinit_locked function which allows for the driver to handle the state
changes by requesting reset from the periodic timer. The second fix
resolves an issue where RSS was being configured as though it is using
the maximum number of queue. This can cause the device to drop a lot
of receive traffic, as the packets get assigned to non-functional queues.
This is resolved by only configuring RSS with the number of active queues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As some C45 10G PHYs(e.g. Cortina CS4315/CS4340 PHY) have
zero Devices In package, current driver can't get correct
devices_in_package value by non-zero Devices In package.
so let's probe more with zero Devices In package to support
more C45 PHYs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all silicon implementations of the Freescale FEC hardware module
have the RACC (Receive Accelerator Function) register, so we should not
be trying to access it on those that don't. Currently none of the ColdFire
based parts with a FEC have it.
Support for RACC was introduced by commit 4c09eed9 ("net: fec: Enable imx6
enet checksum acceleration"). A fix was introduced in commit d1391930
("net: fec: Fix build for MCF5272") that disables its use on the ColdFire
M5272 part, but it doesn't fix the general case of other ColdFire parts.
To fix we create a quirk flag, FEC_QUIRK_HAS_RACC, and check it before
working with the RACC register.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When limiting phy link speed using "max-speed" to 100mbps or less on a
giga bit phy, phy never completes auto negotiation and phy state
machine is held in PHY_AN. Fixing this issue by comparing the giga
bit advertise though phydev->supported doesn't have it but phy has
BMSR_ESTATEN set. So that auto negotiation is restarted as old and
new advertise are different and link comes up fine.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA master netdev promiscuity counter was not being properly
decremented on slave device open error path.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: Gilad Ben-Yossef <giladb@ezchip.com>
CC: David S. Miller <davem@davemloft.net>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Andrew Lunn <andrew@lunn.ch>
CC: Scott Feldman <sfeldma@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Miller says:
====================
Get rid of sock->sk_protinfo.
These two patches get rid of the last remaining user of sk_protinfo
(ax25) and then really gets rid of the struct member.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_ACPI=n:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c: In function ‘xgene_enet_get_resources’:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:951: warning: ‘ret’ may be used uninitialized in this function
If the driver is bound to a legacy platform device, ret will contain
arbitrary data. If it is non-zero, it will be returned to the caller as
an error code.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/flow_dissector.c: In function ‘__skb_flow_dissect’:
net/core/flow_dissector.c:132: warning: ‘ip_proto’ may be used uninitialized in this function
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function netif_set_real_num_tx_queues() will return -EINVAL if
the second parameter < 1, so call this function with the second
parameter set to 0 is meaningless.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1f66d161ab
("tipc: introduce starvation free send algorithm")
we introduced a counter per priority level for buffers
in the link backlog queue. We also introduced a new
function tipc_link_purge_backlog(), to reset these
counters to zero when the link is reset.
Unfortunately, we missed to call this function when
the broadcast link is reset, with the result that the
values of these counters might be permanently skewed
when new nodes are attached. This may in the worst case
lead to permananent, but spurious, broadcast link
congestion, where no broadcast packets can be sent at
all.
We fix this bug with this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will only configure as many queues as there are available
CPUs, up the maximum number of queues. However, it always configures
RSS as though it is using the maximum number of queues. This can cause
the device to drop a lot of RX traffic, as the packets get assigned to
nonfunctional queues.
Fix this by only configuring RSS with the number of active queues.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Down was requesting queue disables, but then exited immediately
without waiting for the queues to actually disable. This could
allow any function called after i40evf_down to run immediately,
including i40evf_up, and causes a memory leak.
Removing the whole reinit_locked function is the best way
to go about this, and allows for the driver to handle the
state changes by requesting reset from the periodic timer.
Also, add a couple WARN_ONs in slow path to help us recognize
if we re-introduce this issue or missed any cases.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SPT hardware does not require this driver workaround.
Removed the conditional that caused K1 workaround execution on SPT.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to clocking changes in the Skylake platform, there was i219
data corruption. To work around this, HW team reported the need
to increase the minimum gap between the PHY FIFO read and write pointers.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SPT/i219, there were CRC errors in speed 10/100 full duplex.
The solution given by the HW team is to increase the IPG from 8 to 0xC
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i219, there is a hardware bug that prevented ULP entry.
A side effect of the original software fix for this was that EEE in
Sx couldn't be enabled.
This patch implements a modified flow that allows both ULP and EEE in Sx.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On power up, the MAC - PHY interface needs to be set to PCIe, even if
cable is disconnected. In ME systems, the ME handles this on exit from
Sx state. In non-ME, the driver handles it. Added a check for non-ME
system to the driver code that handles that.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e_disable_aspm called pci_disable_link_state_locked which requires
pci_bus_sem to be held, but is also called from places where this semaphore
was not previously acquired. This patch implements two flavors of
disable_aspm, one that acquires the lock, and the other (_locked) which
should be called when the semaphore is already acquired.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version of igb to igb-5.2.18
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable IPv6 extension header processing as per hardware errata.
Also fix copyright date.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yuval Mintz says:
====================
bnx2x: various fixes
This patch series contains several small fixes [with the possible
exception of the first 2 link fixes] for various driver flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to FW constraints, driver must make sure that transmitted SKBs will
not be too fragmented, or in the case that they are - that each 'window'
of fragments passed to the FW would contain at least an mss worth of data.
For encapsultaed packets the calculation is wrong, since it ignores the
inner headers in the calculation of the headers' length.
This could lead to a FW assertion in case of a too-fragmented encapsulated
packet.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During an error flow when trying to access the nvram the driver doesn't
release the hw lock it acquired.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since driver statistics flow access MACs and those might reset during
link re-configurations, when we're about to change link properties we
have to make sure that statistics are not operational.
Statisics would be re-enabled [i.e., gathering of statistics would
re-commence] once physical link is achieved again.
Since driver employs a link-flap avoidance scheme, there are scenarios
where driver will receive no indication that the new link is up, and
as a result the statistics would not be re-enabled.
Preventing LFA from working in such cases would guarantee that we'll
always receive such indications and thus will fix statistics gathering.
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
20g-capable devices are not configured properly for self-test, using
10g as their speed which cause the link indication to remain down and
fail the internal loopback test.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bug in today's driver where VF requests to add/remove MAC filters
always reach the Hypervisor as add requests.
This prevents the VF from changing its MAC address, as it cannot remove the
previously configured MAC and runs out of MAC credits.
Signed-off-by: Shahed Shaikh <Shahed.Shaikh@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scratchpad is a shared block between all functions of a given device.
Due to HW limitations, we can't properly close its parity notifications
to all functions on legal flows.
E.g., it's possible that while taking a register dump from one function
a parity error would be triggered on other functions.
Today driver doesn't consider this parity as a 'real' parity unless its
being accompanied by additional indications [which would happen in a real
parity scenario]; But it does print notifications for such events in the
system logs.
This eliminates such prints - in case of real parities driver would have
additional indications; But if this is the only signal user will not even
see a parity being logged in the system.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each time a flow finishes reads from the classification shadow
configuration in the driver, that flow would check for pending commands
and pass them to FW if possible.
In case there's already a completion pending command, I.e., a ramrod
that has been sent to the FW and is yet to be completed while said flow
tries to configure the pending command we would get a false error message
in logs [and panic if SOE was used for driver compilation] since the
command could not have been completed.
This prevents said print [and panic]; The pending command will be sent by
the time the completion of the current sent command would arrive.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool shows KR supported/advertised speeds incorrectly as baseT
in cases the board is in fact KR-base.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes several issues relating to asymmetric configuration:
1. When user requests to disable TX, the local-device needs to
advertise both PAUSE and ASM_DIR, but to avoid transmitting pause
frames. In the 578xx, it would ignore the TX disable.
2. When user advertises RX-only, ASM_DIR was advertised instead of
PAUSE/ASM_DIR.
3. When changing mode, the advertised PAUSE/ASM_DIR was not cleared
before setting new one, so disabling RX or TX had no impact on the
'advertised' as appeared in the 'ethtool -a' output.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in the validation rules for flower's attributes
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use spinlock to access a single flag. We can avoid spin_locks by using
atomic variable and atomic_cmpxchg(). Use atomic_cmpxchg to set the flag
for idle to poll. And a simple atomic_set to unlock (set idle from poll).
In napi poll, if gro is enabled, we call napi_gro_receive() to deliver the
packets. Before we call napi_complete(), i.e while re-polling, if low
latency busy poll is called, we use netif_receive_skb() to deliver the packets.
At this point if there are some skb's held in GRO, busy poll could deliver the
packets out of order. So we call napi_gro_flush() to flush skbs before we
move the napi poll to idle.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitesse VSC8641 is compatible with Vitesse 82xx
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_GIANFAR is not depended on FSL_SOC, it
can be built on non-PPC platforms.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a missing assignment so the "if (ret)" on the next line is
never true.
Fixes: f21fb3ed36 ('Add support of Cavium Liquidio ethernet adapters')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to unlock before returning here.
Fixes: a0d2f20650 ('Renesas Ethernet AVB PTP clock driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
mlx4 driver fixes, June 24, 2015
Some fixes that we made recently, all need to go into stable.
patch #1 "net/mlx4_en: Release TX QP when destroying TX ring" and patch #3
"Fix wrong csum complete report when rxvlan offload is disabled" to >= 3.19
patch #2 "Wake TX queues only when there's enough room" addressing a bug
which is there from day one... should go to whatever kernels it's still applicable
patch #4 "mlx4: Disable HA for SRIOV PF RoCE devices" to >= 4.0
The patches are marked with net but are made against net-next,
as the net tree still doesn't contain all the net-next bits.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When in HA mode, the driver exposes an IB (RoCE) device instance with only
one port. Under SRIOV, the existing implementation doesn't go well with
the PF RoCE driver's role of Special QPs Para-Virtualization, etc.
As such, disable HA for the mlx4 PF RoCE device in SRIOV mode.
Fixes: a575009030 ('IB/mlx4: Add port aggregation support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check_csum() function relied on hwtstamp_rx_filter to know if rxvlan
offload is disabled. This is wrong since rxvlan offload can be switched
on/off regardless of hwtstamp_rx_filter.
Also moved check_csum to query CQE information to identify VLAN packets
and removed the check of IP packets, since it has been validated before.
Fixes: f8c6455bb0 ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indication of a single completed packet, marked by txbbs_skipped
being bigger then zero, in not enough in order to wake up a
stopped TX queue. The completed packet may contain a single TXBB,
while next packet to be sent (after the wake up) may have multiple
TXBBs (LSO/TSO packets for example), causing overflow in queue followed
by WQE corruption and TX queue timeout.
Instead, wake the stopped queue only when there's enough room for the
worst case (maximum sized WQE) packet that we should need to handle after
the queue is opened again.
Also created an helper routine - mlx4_en_is_tx_ring_full, which checks
if the current TX ring is full or not. It provides better code readability
and removes code duplication.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX ring QP wasn't released at mlx4_en_destroy_tx_ring. Instead, the code
used the deprecated base_tx_qpn field. Move TX QP release to
mlx4_en_destroy_tx_ring and remove the base_tx_qpn field.
Fixes: ddae0349fd ('net/mlx4: Change QP allocation scheme')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge first patchbomb from Andrew Morton:
- a few misc things
- ocfs2 udpates
- kernel/watchdog.c feature work (took ages to get right)
- most of MM. A few tricky bits are held up and probably won't make 4.2.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (91 commits)
mm: kmemleak_alloc_percpu() should follow the gfp from per_alloc()
mm, thp: respect MPOL_PREFERRED policy with non-local node
tmpfs: truncate prealloc blocks past i_size
mm/memory hotplug: print the last vmemmap region at the end of hot add memory
mm/mmap.c: optimization of do_mmap_pgoff function
mm: kmemleak: optimise kmemleak_lock acquiring during kmemleak_scan
mm: kmemleak: avoid deadlock on the kmemleak object insertion error path
mm: kmemleak: do not acquire scan_mutex in kmemleak_do_cleanup()
mm: kmemleak: fix delete_object_*() race when called on the same memory block
mm: kmemleak: allow safe memory scanning during kmemleak disabling
memcg: convert mem_cgroup->under_oom from atomic_t to int
memcg: remove unused mem_cgroup->oom_wakeups
frontswap: allow multiple backends
x86, mirror: x86 enabling - find mirrored memory ranges
mm/memblock: allocate boot time data structures from mirrored memory
mm/memblock: add extra "flags" to memblock to allow selection of memory based on attribute
mm: do not ignore mapping_gfp_mask in page cache allocation paths
mm/cma.c: fix typos in comments
mm/oom_kill.c: print points as unsigned int
mm/hugetlb: handle races in alloc_huge_page and hugetlb_reserve_pages
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=248K
-----END PGP SIGNATURE-----
Merge tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull pstore updates from Tony Luck:
"Miscellaneous pstore improvements"
* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
ramoops: make it possible to change mem_type param.
pstore/ram: verify ramoops header before saving record
fs/pstore: Optimization function ramoops_init_przs
fs/pstore: update the backend parameter in pstore module
pstore: do not use message compression without lock
Pull f2fs updates from Jaegeuk Kim:
"New features:
- per-file encryption (e.g., ext4)
- FALLOC_FL_ZERO_RANGE
- FALLOC_FL_COLLAPSE_RANGE
- RENAME_WHITEOUT
Major enhancement/fixes:
- recovery broken superblocks
- enhance f2fs_trim_fs with a discard_map
- fix a race condition on dentry block allocation
- fix a deadlock during summary operation
- fix a missing fiemap result
.. and many minor bug fixes and clean-ups were done"
* tag 'for-f2fs-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (83 commits)
f2fs: do not trim preallocated blocks when truncating after i_size
f2fs crypto: add alloc_bounce_page
f2fs crypto: fix to handle errors likewise ext4
f2fs: drop the volatile_write flag only
f2fs: skip committing valid superblock
f2fs: setting discard option in parse_options()
f2fs: fix to return exact trimmed size
f2fs: support FALLOC_FL_INSERT_RANGE
f2fs: hide common code in f2fs_replace_block
f2fs: disable the discard option when device doesn't support
f2fs crypto: remove alloc_page for bounce_page
f2fs: fix a deadlock for summary page lock vs. sentry_lock
f2fs crypto: clean up error handling in f2fs_fname_setup_filename
f2fs crypto: avoid f2fs_inherit_context for symlink
f2fs crypto: do not set encryption policy for non-directory by ioctl
f2fs crypto: allow setting encryption policy once
f2fs crypto: check context consistent for rename2
f2fs: avoid duplicated code by reusing f2fs_read_end_io
f2fs crypto: use per-inode tfm structure
f2fs: recovering broken superblock during mount
...
Pull UDF fixes and cleanups from Jan Kara:
"The contains some small fixes and improvements in error handling for
UDF.
Bundled is also one ext3 coding style fix and a fix in quota
documentation"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: fix udf_load_pvoldesc()
udf: remove double err declaration in udf_file_write_iter()
UDF: support NFSv2 export
fs: ext3: super: fixed a space coding style issue
quota: Update documentation
udf: Return error from udf_find_entry()
udf: Make udf_get_filename() return error instead of 0 length file name
udf: bug on exotic flag in udf_get_filename()
udf: improve error management in udf_CS0toNLS()
udf: improve error management in udf_CS0toUTF8()
udf: unicode: update function name in comments
udf: remove unnecessary test in udf_build_ustr_exact()
udf: Return -ENOMEM when allocation fails in udf_get_filename()
