All the wakeup sources we possibly want will go through the interrupt
controller, so the parent IRQ must not be masked during suspend, or
there won't be any way to wake up the system.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200819180602.136969-1-paul@crapouillou.net
In the current code, when the eoi callback of the exti clears the pending
bit of the current interrupt, it will first read the values of fpr and
rpr, then logically OR the corresponding bit of the interrupt number,
and finally write back to fpr and rpr.
We found through experiments that if two exti interrupts,
we call them int1/int2, arrive almost at the same time. in our scenario,
the time difference is 30 microseconds, assuming int1 is triggered first.
there will be an extreme scenario: both int's pending bit are set to 1,
the irq handle of int1 is executed first, and eoi handle is then executed,
at this moment, all pending bits are cleared, but the int 2 has not
finally been reported to the cpu yet, which eventually lost int2.
According to stm32's TRM description about rpr and fpr: Writing a 1 to this
bit will trigger a rising edge event on event x, Writing 0 has no
effect.
Therefore, when clearing the pending bit, we only need to clear the
pending bit of the irq.
Fixes: 927abfc446 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain")
Signed-off-by: qiuguorui1 <qiuguorui1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # v4.18+
Link: https://lore.kernel.org/r/20200820031629.15582-1-qiuguorui1@huawei.com
It has become obvious that switching a number of irqchip drivers
to being platform drivers without considering the platform was a
mistake. We have multiple reports of end-point drivers not
probing because the irqchip driver isn't there yet, breaking
the expectations of the users.
This patch reverts:
920ecb8c35 ("irqchip/mtk-cirq: Convert to a platform driver")
f97dbf48ca ("irqchip/mtk-sysirq: Convert to a platform driver")
5be57099d4 ("irqchip/qcom-pdc: Switch to using IRQCHIP_PLATFORM_DRIVER helper macros")
95bf9305d2 ("irqchip/qcom-pdc: Allow QCOM_PDC to be loadable as a permanent module")
and leave QCOM PDC, MTK sysrq and cirq drivers as built-in, special purpose
drivers for the time being until we have worked out a better solution.
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reported-by: Frank Wunderlich <linux@fw-web.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/93debe6a0308b66d3f307af67ba7ec2c@kernel.org
It was a good idea to move it out at first, but the irqchip code
is still tightly connected to the s3c24xx platform code and uses
multiple internal header files, so just move it back for the
time being to avoid those dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-21-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
When probing an interrupt controller that is behind a parent,
we try to check whether the parent domain is available as
an indication that we can actually try to probe.
Unfortunately, we are checking this with the firmware node of
the about to be probed device, not the parent. This is obviously
bound to fail.
Instead, use the parent node.
Fixes: f8410e6265 ("irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Driver assumes that Interrupt parent to Interrupt Aggregator is always
Interrupt router. This is not true always and GIC can be a parent to
Interrupt Aggregator. Update the driver to detect the parent and request
the parent irqs accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806074826.24607-11-lokeshvutla@ti.com
Even though DT doesn't make active use of id field in platform_device, we cannot
hijack it to store TISCI device id. So create a field in struct ti_sci_inta
for storing TISCI id and drop usage of id field in platform_device.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806074826.24607-10-lokeshvutla@ti.com
Driver assumes that Interrupt parent to Interrupt router is always GIC.
This is not true always and an Interrupt Router can be a parent to
Interrupt Router. Update the driver to detect the parent and request the
parent irqs accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806074826.24607-7-lokeshvutla@ti.com
- Infrastructure to allow building irqchip drivers as modules
- Consolidation of irqchip ACPI probing
- Removal of the EOI-preflow interrupt handler which was required for
SPARC support and became obsolete after SPARC was converted to
use sparse interrupts.
- Cleanups, fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----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=KA8b
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The usual boring updates from the interrupt subsystem:
- Infrastructure to allow building irqchip drivers as modules
- Consolidation of irqchip ACPI probing
- Removal of the EOI-preflow interrupt handler which was required for
SPARC support and became obsolete after SPARC was converted to use
sparse interrupts.
- Cleanups, fixes and improvements all over the place"
* tag 'irq-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
irqchip/loongson-pch-pic: Fix the misused irq flow handler
irqchip/loongson-htvec: Support 8 groups of HT vectors
irqchip/loongson-liointc: Fix misuse of gc->mask_cache
dt-bindings: interrupt-controller: Update Loongson HTVEC description
irqchip/imx-intmux: Fix irqdata regs save in imx_intmux_runtime_suspend()
irqchip/imx-intmux: Implement intmux runtime power management
irqchip/gic-v4.1: Use GFP_ATOMIC flag in allocate_vpe_l1_table()
irqchip: Fix IRQCHIP_PLATFORM_DRIVER_* compilation by including module.h
irqchip/stm32-exti: Map direct event to irq parent
irqchip/mtk-cirq: Convert to a platform driver
irqchip/mtk-sysirq: Convert to a platform driver
irqchip/qcom-pdc: Switch to using IRQCHIP_PLATFORM_DRIVER helper macros
irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros
irqchip: irq-bcm2836.h: drop a duplicated word
irqchip/gic-v4.1: Ensure accessing the correct RD when writing INVALLR
irqchip/irq-bcm7038-l1: Guard uses of cpu_logical_map
irqchip/gic-v3: Remove unused register definition
irqchip/qcom-pdc: Allow QCOM_PDC to be loadable as a permanent module
genirq: Export irq_chip_retrigger_hierarchy and irq_chip_set_vcpu_affinity_parent
irqdomain: Export irq_domain_update_bus_token
...
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
that helps the debugging of IRQ affinity logic bugs, and fix a memory leak.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oKU9
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-08-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Fix a recent IRQ affinities regression, add in a missing debugfs
printout that helps the debugging of IRQ affinity logic bugs, and fix
a memory leak"
* tag 'irq-urgent-2020-08-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/debugfs: Add missing irqchip flags
genirq/affinity: Make affinity setting if activated opt-in
irqdomain/treewide: Free firmware node after domain removal
- Removal of the tremendously unpopular read_barrier_depends() barrier,
which is a NOP on all architectures apart from Alpha, in favour of
allowing architectures to override READ_ONCE() and do whatever dance
they need to do to ensure address dependencies provide LOAD ->
LOAD/STORE ordering. This work also offers a potential solution if
compilers are shown to convert LOAD -> LOAD address dependencies into
control dependencies (e.g. under LTO), as weakly ordered architectures
will effectively be able to upgrade READ_ONCE() to smp_load_acquire().
The latter case is not used yet, but will be discussed further at LPC.
- Make the MSI/IOMMU input/output ID translation PCI agnostic, augment
the MSI/IOMMU ACPI/OF ID mapping APIs to accept an input ID
bus-specific parameter and apply the resulting changes to the device
ID space provided by the Freescale FSL bus.
- arm64 support for TLBI range operations and translation table level
hints (part of the ARMv8.4 architecture version).
- Time namespace support for arm64.
- Export the virtual and physical address sizes in vmcoreinfo for
makedumpfile and crash utilities.
- CPU feature handling cleanups and checks for programmer errors
(overlapping bit-fields).
- ACPI updates for arm64: disallow AML accesses to EFI code regions and
kernel memory.
- perf updates for arm64.
- Miscellaneous fixes and cleanups, most notably PLT counting
optimisation for module loading, recordmcount fix to ignore
relocations other than R_AARCH64_CALL26, CMA areas reserved for
gigantic pages on 16K and 64K configurations.
- Trivial typos, duplicate words.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE5RElWfyWxS+3PLO2a9axLQDIXvEFAl8oTcsACgkQa9axLQDI
XvEj6hAAkn39mO5xrR/Vhpg3DyFPk63ZlMSX9SsOeVyaLbovT6stTs1XAZXPpnkt
rV3gwACyGSrqH6+uey9pHgHJuPF2TdrGEVK08yVKo9KGW/6yXSIncdKFE4jUJ/WJ
wF5j7eMET2aGzcpm5AlzMmq6HOrKB8nZac9H8/x6H+Ox2WdgJkEjOkDvyqACUyum
N3FsTZkWj2pIkTXHNgDZ8KjxVLO8HlFaB2hkxFDl9NPlX2UTCQJ8Tg1KiPLafKaK
gUvH4usQDFdb5RU/UWogre37J4emO0ZTApZOyju+U+PMMWlWVHjZ4isUIS9zz/AE
JNZ23dnKZX2HrYa5p8HZx175zwj/vXUqUHCZPLvQXaAudCEhF8BVljPiG0e80FV5
GHFUgUbylKspp01I/9L+2JvsG96Mr0e+P3Sx7L2HTI42cmtoSa14+MpoSRj7zlft
Qcl8hfrVOjCjUnFRHa/1y1cGvnD9GbgnKJR7zgVxl9bD/Jd48r1HUtwRORZCzWFr
mRPVbPS72fWxMzMV9DZYJm02jJY9kLX2BMl49njbB8MhAhzOvrMVzoVVtMMeRFLR
XHeJpmg36W09FiRGe7LRXlkXIhCQzQG2bJfiphuupCfhjRAitPoq8I925G6Pig60
c8RWaXGU7PrEsdMNrL83vekvGKgqrkoFkRVtsCoQ2X6Hvu/XdYI=
=mh79
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 and cross-arch updates from Catalin Marinas:
"Here's a slightly wider-spread set of updates for 5.9.
Going outside the usual arch/arm64/ area is the removal of
read_barrier_depends() series from Will and the MSI/IOMMU ID
translation series from Lorenzo.
The notable arm64 updates include ARMv8.4 TLBI range operations and
translation level hint, time namespace support, and perf.
Summary:
- Removal of the tremendously unpopular read_barrier_depends()
barrier, which is a NOP on all architectures apart from Alpha, in
favour of allowing architectures to override READ_ONCE() and do
whatever dance they need to do to ensure address dependencies
provide LOAD -> LOAD/STORE ordering.
This work also offers a potential solution if compilers are shown
to convert LOAD -> LOAD address dependencies into control
dependencies (e.g. under LTO), as weakly ordered architectures will
effectively be able to upgrade READ_ONCE() to smp_load_acquire().
The latter case is not used yet, but will be discussed further at
LPC.
- Make the MSI/IOMMU input/output ID translation PCI agnostic,
augment the MSI/IOMMU ACPI/OF ID mapping APIs to accept an input ID
bus-specific parameter and apply the resulting changes to the
device ID space provided by the Freescale FSL bus.
- arm64 support for TLBI range operations and translation table level
hints (part of the ARMv8.4 architecture version).
- Time namespace support for arm64.
- Export the virtual and physical address sizes in vmcoreinfo for
makedumpfile and crash utilities.
- CPU feature handling cleanups and checks for programmer errors
(overlapping bit-fields).
- ACPI updates for arm64: disallow AML accesses to EFI code regions
and kernel memory.
- perf updates for arm64.
- Miscellaneous fixes and cleanups, most notably PLT counting
optimisation for module loading, recordmcount fix to ignore
relocations other than R_AARCH64_CALL26, CMA areas reserved for
gigantic pages on 16K and 64K configurations.
- Trivial typos, duplicate words"
Link: http://lkml.kernel.org/r/20200710165203.31284-1-will@kernel.org
Link: http://lkml.kernel.org/r/20200619082013.13661-1-lorenzo.pieralisi@arm.com
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (82 commits)
arm64: use IRQ_STACK_SIZE instead of THREAD_SIZE for irq stack
arm64/mm: save memory access in check_and_switch_context() fast switch path
arm64: sigcontext.h: delete duplicated word
arm64: ptrace.h: delete duplicated word
arm64: pgtable-hwdef.h: delete duplicated words
bus: fsl-mc: Add ACPI support for fsl-mc
bus/fsl-mc: Refactor the MSI domain creation in the DPRC driver
of/irq: Make of_msi_map_rid() PCI bus agnostic
of/irq: make of_msi_map_get_device_domain() bus agnostic
dt-bindings: arm: fsl: Add msi-map device-tree binding for fsl-mc bus
of/device: Add input id to of_dma_configure()
of/iommu: Make of_map_rid() PCI agnostic
ACPI/IORT: Add an input ID to acpi_dma_configure()
ACPI/IORT: Remove useless PCI bus walk
ACPI/IORT: Make iort_msi_map_rid() PCI agnostic
ACPI/IORT: Make iort_get_device_domain IRQ domain agnostic
ACPI/IORT: Make iort_match_node_callback walk the ACPI namespace for NC
arm64: enable time namespace support
arm64/vdso: Restrict splitting VVAR VMA
arm64/vdso: Handle faults on timens page
...
Loongson PCH PIC is a standard level triggered PIC, and it need to clear
interrupt during unmask.
Fixes: ef8c01eb64 ("irqchip: Add Loongson PCH PIC controller")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lore.kernel.org/r/1596099090-23516-6-git-send-email-chenhc@lemote.com
The original version can only used by old Loongson-3 which only use 4
groups of HT vectors. Now Loongson-3A R4 can use 8 groups, so improve
the driver to support all 8 groups.
Fixes: 818e915fba ("irqchip: Add Loongson HyperTransport Vector support")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lore.kernel.org/r/1596099090-23516-5-git-send-email-chenhc@lemote.com
In gc->mask_cache bits, 1 means enabled and 0 means disabled, but in the
loongson-liointc driver mask_cache is misused by reverting its meaning.
This patch fix the bug and update the comments as well.
Fixes: dbb1522679 ("irqchip: Add driver for Loongson I/O Local Interrupt Controller")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1596099090-23516-4-git-send-email-chenhc@lemote.com
Gcc report warning as follows:
drivers/irqchip/irq-imx-intmux.c:316:29: warning:
variable 'irqchip_data' set but not used [-Wunused-but-set-variable]
316 | struct intmux_irqchip_data irqchip_data;
| ^~~~~~~~~~~~
irqdata regs is stored to this variable on the stack in
imx_intmux_runtime_suspend(), which means a nop. this commit
fix to save regs to the right place.
Fixes: bb403111e0 ("irqchip/imx-intmux: Implement intmux runtime power management")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200729155849.33919-1-weiyongjun1@huawei.com
Add ACPI support in the fsl-mc driver. Driver parses MC DSDT table to
extract memory and other resources.
Interrupt (GIC ITS) information is extracted from the MADT table
by drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c.
IORT table is parsed to configure DMA.
Signed-off-by: Makarand Pawagi <makarand.pawagi@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200619082013.13661-13-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The DPRC driver is not taking into account the msi-map property
and assumes that the icid is the same as the stream ID. Although
this assumption is correct, generalize the code to include a
translation between icid and streamID.
Furthermore do not just copy the MSI domain from parent (for child
containers), but use the information provided by the msi-map property.
If the msi-map property is missing from the device tree retain the old
behaviour for backward compatibility ie the child DPRC objects
inherit the MSI domain from the parent.
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200619082013.13661-12-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
John reported that on a RK3288 system the perf per CPU interrupts are all
affine to CPU0 and provided the analysis:
"It looks like what happens is that because the interrupts are not per-CPU
in the hardware, armpmu_request_irq() calls irq_force_affinity() while
the interrupt is deactivated and then request_irq() with IRQF_PERCPU |
IRQF_NOBALANCING.
Now when irq_startup() runs with IRQ_STARTUP_NORMAL, it calls
irq_setup_affinity() which returns early because IRQF_PERCPU and
IRQF_NOBALANCING are set, leaving the interrupt on its original CPU."
This was broken by the recent commit which blocked interrupt affinity
setting in hardware before activation of the interrupt. While this works in
general, it does not work for this particular case. As contrary to the
initial analysis not all interrupt chip drivers implement an activate
callback, the safe cure is to make the deferred interrupt affinity setting
at activation time opt-in.
Implement the necessary core logic and make the two irqchip implementations
for which this is required opt-in. In hindsight this would have been the
right thing to do, but ...
Fixes: baedb87d1b ("genirq/affinity: Handle affinity setting on inactive interrupts correctly")
Reported-by: John Keeping <john@metanate.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/87blk4tzgm.fsf@nanos.tec.linutronix.de
When the system is suspended, we can explicitly disable clock to save
power. To achieve this, we need save registers' state since it could be
lost after power off.
Implement power management which will:
- Turn the clock off after probing
- Disable clock and save registers' state on system suspend, as
well as enable clock and restore registers' state on resume
- Rely on the Power Domain framework to shutdown the intmux
power domain
Without CONFIG_PM, the clock is always on after probe stage.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[maz: revamped commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200727141734.24890-2-qiangqing.zhang@nxp.com
Booting the latest kernel with DEBUG_ATOMIC_SLEEP=y on a GICv4.1 enabled
box, I get the following kernel splat:
[ 0.053766] BUG: sleeping function called from invalid context at mm/slab.h:567
[ 0.053767] in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/1
[ 0.053769] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.8.0-rc3+ #23
[ 0.053770] Call trace:
[ 0.053774] dump_backtrace+0x0/0x218
[ 0.053775] show_stack+0x2c/0x38
[ 0.053777] dump_stack+0xc4/0x10c
[ 0.053779] ___might_sleep+0xfc/0x140
[ 0.053780] __might_sleep+0x58/0x90
[ 0.053782] slab_pre_alloc_hook+0x7c/0x90
[ 0.053783] kmem_cache_alloc_trace+0x60/0x2f0
[ 0.053785] its_cpu_init+0x6f4/0xe40
[ 0.053786] gic_starting_cpu+0x24/0x38
[ 0.053788] cpuhp_invoke_callback+0xa0/0x710
[ 0.053789] notify_cpu_starting+0xcc/0xd8
[ 0.053790] secondary_start_kernel+0x148/0x200
# ./scripts/faddr2line vmlinux its_cpu_init+0x6f4/0xe40
its_cpu_init+0x6f4/0xe40:
allocate_vpe_l1_table at drivers/irqchip/irq-gic-v3-its.c:2818
(inlined by) its_cpu_init_lpis at drivers/irqchip/irq-gic-v3-its.c:3138
(inlined by) its_cpu_init at drivers/irqchip/irq-gic-v3-its.c:5166
It turned out that we're allocating memory using GFP_KERNEL (may sleep)
within the CPU hotplug notifier, which is indeed an atomic context. Bad
thing may happen if we're playing on a system with more than a single
CommonLPIAff group. Avoid it by turning this into an atomic allocation.
Fixes: 5e5168461c ("irqchip/gic-v4.1: VPE table (aka GICR_VPROPBASER) allocation")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200630133746.816-1-yuzenghui@huawei.com
EXTI lines are mainly used to wake-up system from CStop low power mode.
Currently, if a device wants to use a EXTI (direct) line as wakeup line,
it has to declare 2 interrupts:
- one for EXTI used to wake-up system (with dedicated_wake_irq api).
- one for GIC used to get the wake up reason inside the concerned IP.
This split is not really needed as each EXTI line is actually "linked " to
a GIC. So to avoid this useless double interrupt management in each
wake-up driver, this patch lets the STM32 EXTI driver abstract it by
mapping each EXTI line to his corresponding GIC.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200717140717.29606-1-alexandre.torgue@st.com
This driver can work as a platform driver. So covert it to a platform
driver.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Hanks Chen <hanks.chen@mediatek.com>
Link: https://lore.kernel.org/r/20200718000637.3632841-5-saravanak@google.com
This driver can work as a platform driver. So covert it to a platform
driver.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Hanks Chen <hanks.chen@mediatek.com>
Link: https://lore.kernel.org/r/20200718000637.3632841-4-saravanak@google.com
Switch the driver to use the helper macros. In addition to reducing the
number of lines, this also adds module unload protection (if the driver
is compiled as a module) by switching from module_platform_driver to
builtin_platform_driver.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200718000637.3632841-3-saravanak@google.com
Compiling an irqchip driver as a platform driver needs to bunch of
things to be done right:
- Making sure the parent domain is initialized first
- Making sure the device can't be unbound from sysfs
- Disallowing module unload if it's built as a module
- Finding the parent node
- Etc.
Instead of trying to make sure all future irqchip platform drivers get
this right, provide boilerplate macros that take care of all of this.
An example use would look something like this. Where acme_foo_init and
acme_bar_init are similar to what would be passed to IRQCHIP_DECLARE.
IRQCHIP_PLATFORM_DRIVER_BEGIN(acme_irq)
IRQCHIP_MATCH("acme,foo", acme_foo_init)
IRQCHIP_MATCH("acme,bar", acme_bar_init)
IRQCHIP_PLATFORM_DRIVER_END(acme_irq)
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200718000637.3632841-2-saravanak@google.com
The GICv4.1 spec tells us that it's CONSTRAINED UNPREDICTABLE to issue a
register-based invalidation operation for a vPEID not mapped to that RD,
or another RD within the same CommonLPIAff group.
To follow this rule, commit f3a059219b ("irqchip/gic-v4.1: Ensure mutual
exclusion between vPE affinity change and RD access") tried to address the
race between the RD accesses and the vPE affinity change, but somehow
forgot to take GICR_INVALLR into account. Let's take the vpe_lock before
evaluating vpe->col_idx to fix it.
Fixes: f3a059219b ("irqchip/gic-v4.1: Ensure mutual exclusion between vPE affinity change and RD access")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200720092328.708-1-yuzenghui@huawei.com
cpu_logical_map is only defined for CONFIG_SMP builds, when we are in an
UP configuration, the boot CPU is 0.
Fixes: 6468fc18b0 ("irqchip/irq-bcm7038-l1: Add PM support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200724184157.29150-1-f.fainelli@gmail.com
Allows qcom-pdc driver to be loaded as a permanent module
Also, due to the fact that IRQCHIP_DECLARE becomes a no-op when
building as a module, we have to replace it with platform driver
hooks explicitly.
Thanks to Saravana for his help on pointing out the
IRQCHIP_DECLARE issue and guidance on a solution.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20200710231824.60699-4-john.stultz@linaro.org
The sparse tool complains as follows:
drivers/irqchip/irq-mips-gic.c:49:1: warning:
symbol '__pcpu_scope_pcpu_masks' was not declared. Should it be static?
drivers/irqchip/irq-mips-gic.c:620:6: warning:
symbol 'gic_ipi_domain_free' was not declared. Should it be static?
drivers/irqchip/irq-mips-gic.c:634:5: warning:
symbol 'gic_ipi_domain_match' was not declared. Should it be static?
Those symbols are not used outside of irq-mips-gic.c, so marks
them static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200714142245.16124-1-weiyongjun1@huawei.com
Now that the hwspin_lock_timeout_in_atomic() API is available use it.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200706081115.25180-1-alexandre.torgue@st.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
In the function liointc_set_type(), we need to call the function
irq_gc_unlock_irqrestore() before returning.
Fixes: dbb1522679 ("irqchip: Add driver for Loongson I/O Local Interrupt Controller")
Reported-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1594087972-21715-8-git-send-email-yangtiezhu@loongson.cn
irq_domain_alloc_irqs_parent() returns 0 on success and non-zero value
on failure, it is redudant to check its non-zero return value and then
return it, so just remove the variable "ret" and return directly in the
function pch_msi_parent_domain_alloc().
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1594087972-21715-7-git-send-email-yangtiezhu@loongson.cn
Check the return value of irq_domain_translate_twocell() due to
it may returns -EINVAL if failed and use variable fwspec for it,
and then use a new variable parent_fwspec which is proper for
irq_domain_alloc_irqs_parent().
Fixes: ef8c01eb64 ("irqchip: Add Loongson PCH PIC controller")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1594087972-21715-6-git-send-email-yangtiezhu@loongson.cn
In the function htvec_of_init(), system resource "parent_irq"
was not released in an error case. Thus add a jump target for
the completion of the desired exception handling.
Fixes: 818e915fba ("irqchip: Add Loongson HyperTransport Vector support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1594087972-21715-4-git-send-email-yangtiezhu@loongson.cn
LOONGSON_HTPIC depends on MACH_LOONGSON64 and MACH_LOONGSON64 already
selects I8259 in arch/mips/Kconfig, so no need to select I8259 again
when config LOONGSON_HTPIC.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1594087972-21715-3-git-send-email-yangtiezhu@loongson.cn
We need to have a definition for cpu_logical_map[] which on ARM
platforms is provided by asm/smp_plat.h. This header is not
automatically included from linux/smp.h and untangling it is a bit
difficult.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709234141.4901-1-f.fainelli@gmail.com
The UPG_AUX_AON_INTR2 Level 2 interrupt controller node is defined with
the "brcm,upg-aux-aon-l2-intc" compatible string in Device Tree and
behaves as an edge triggered standard Broadcom STB L2 interrupt
controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-7-f.fainelli@gmail.com
The HIF_SPI_INTR2 Level 2 interrupt controller node is defined with the
"brcm,hif-spi-l2-intc" compatible string in Device Tree and behaves as
an edge triggered standard Broadcom STB L2 interrupt controller.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-5-f.fainelli@gmail.com
Utilize the Broadcom interrupt controller standard property
"brcm,irq-can-wake" to flag whether this particular interrupt controller
instance is wake-up capable.
Since we do not know what type of parent interrupt controller we are
interfaced with, ensure that enable_irq_wake() is called early on.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-3-f.fainelli@gmail.com
Utilize the Broadcom interrupt controller standard property
"brcm,irq-can-wake" to flag whether this particular interrupt controller
instance is wake-up capable.
Since we do not know what type of parent interrupt controller we are
interfaced with, ensure that enable_irq_wake() is called early on.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-2-f.fainelli@gmail.com
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl8DWosUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroO8cAf/UskNg8qoLGG17rQwhFpmigSllbiJ
TAyi3tpb1Y0Z2MfYeGkeiEb1L34bS28Cxl929DoqI3hrXy1wDCmsHPB5c3URXrzd
aswvr7pJtQV9iH1ykaS2woFJnOUovMFsFYMhj46yUPoAvdKOZKvuqcduxbogYHFw
YeRhS+1lGfiP2A0j3O/nnNJ0wq+FxKO46G3CgWeqG75+FSL6y/tl0bZJUMKKajQZ
GNaOv/CYCHAfUdvgy0ZitRD8lV8yxng3dYGjm+a52Kmn2ZWiFlxNrnxzHySk16Rn
Lq6MfFOqgrYpoZv7SnsFYnRE05U5bEFQ8BGr22fImQ+ktKDgq+9gv6cKwA==
=+DN/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Bugfixes and a one-liner patch to silence a sparse warning"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm64: Stop clobbering x0 for HVC_SOFT_RESTART
KVM: arm64: PMU: Fix per-CPU access in preemptible context
KVM: VMX: Use KVM_POSSIBLE_CR*_GUEST_BITS to initialize guest/host masks
KVM: x86: Mark CR4.TSD as being possibly owned by the guest
KVM: x86: Inject #GP if guest attempts to toggle CR4.LA57 in 64-bit mode
kvm: use more precise cast and do not drop __user
KVM: x86: bit 8 of non-leaf PDPEs is not reserved
KVM: X86: Fix async pf caused null-ptr-deref
KVM: arm64: vgic-v4: Plug race between non-residency and v4.1 doorbell
KVM: arm64: pvtime: Ensure task delay accounting is enabled
KVM: arm64: Fix kvm_reset_vcpu() return code being incorrect with SVE
KVM: arm64: Annotate hyp NMI-related functions as __always_inline
KVM: s390: reduce number of IO pins to 1
In an effort to enable -Wcast-function-type in the top-level Makefile to
support Control Flow Integrity builds, there are the need to remove all
the function callback casts.
To do this, modify the IRQCHIP_ACPI_DECLARE macro to use the new defined
macro ACPI_DECLARE_SUBTABLE_PROBE_ENTRY instead of the macro
ACPI_DECLARE_PROBE_ENTRY. This is necessary to be able to initialize the
the acpi_probe_entry struct using the probe_subtbl field instead of the
probe_table field and avoid function cast mismatches.
Also, modify the prototype of the functions used by the invocation of the
IRQCHIP_ACPI_DECLARE macro to match all the parameters.
Co-developed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Oscar Carter <oscar.carter@gmx.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20200530143430.5203-3-oscar.carter@gmx.com
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200616230923.GA24937@embeddedor
This driver may take a regular spinlock when a raw spinlock
(irq_desc->lock) is already taken which results in the following
lockdep splat:
=============================
[ BUG: Invalid wait context ]
5.7.0-rc7 #1 Not tainted
-----------------------------
swapper/0/0 is trying to lock:
ffffff800303b798 (&chip_data->lock){....}-{3:3}, at: mtk_sysirq_set_type+0x48/0xc0
other info that might help us debug this:
context-{5:5}
2 locks held by swapper/0/0:
#0: ffffff800302ee68 (&desc->request_mutex){....}-{4:4}, at: __setup_irq+0xc4/0x8a0
#1: ffffff800302ecf0 (&irq_desc_lock_class){....}-{2:2}, at: __setup_irq+0xe4/0x8a0
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.7.0-rc7 #1
Hardware name: Pumpkin MT8516 (DT)
Call trace:
dump_backtrace+0x0/0x180
show_stack+0x14/0x20
dump_stack+0xd0/0x118
__lock_acquire+0x8c8/0x2270
lock_acquire+0xf8/0x470
_raw_spin_lock_irqsave+0x50/0x78
mtk_sysirq_set_type+0x48/0xc0
__irq_set_trigger+0x58/0x170
__setup_irq+0x420/0x8a0
request_threaded_irq+0xd8/0x190
timer_of_init+0x1e8/0x2c4
mtk_gpt_init+0x5c/0x1dc
timer_probe+0x74/0xf4
time_init+0x14/0x44
start_kernel+0x394/0x4f0
Replace the spinlock_t with raw_spinlock_t to avoid this warning.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200615074445.3579-1-brgl@bgdev.pl
There are registers and functions in the header file
that are only used inside the driver. Move these into
the driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200607215124.48638-2-linus.walleij@linaro.org
It should be "ti.com" instead of "ticom".
Fixes: 9f1463b86c ("irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/1591437017-5295-3-git-send-email-yangtiezhu@loongson.cn
When call function devm_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Fixes: 9f1463b86c ("irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/1591437017-5295-2-git-send-email-yangtiezhu@loongson.cn
In the function ti_sci_inta_set_type(), the statement "return -EINVAL;"
out of switch case is dead code, remove it.
Fixes: 9f1463b86c ("irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/1591437017-5295-1-git-send-email-yangtiezhu@loongson.cn
When making a vPE non-resident because it has hit a blocking WFI,
the doorbell can fire at any time after the write to the RD.
Crucially, it can fire right between the write to GICR_VPENDBASER
and the write to the pending_last field in the its_vpe structure.
This means that we would overwrite pending_last with stale data,
and potentially not wakeup until some unrelated event (such as
a timer interrupt) puts the vPE back on the CPU.
GICv4 isn't affected by this as we actively mask the doorbell on
entering the guest, while GICv4.1 automatically manages doorbell
delivery without any hypervisor-driven masking.
Use the vpe_lock to synchronize such update, which solves the
problem altogether.
Fixes: ae699ad348 ("irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The GIC driver uses a RMW sequence to update the affinity, and
relies on the gic_lock_irqsave/gic_unlock_irqrestore sequences
to update it atomically.
But these sequences only expand into anything meaningful if
the BL_SWITCHER option is selected, which almost never happens.
It also turns out that using a RMW and locks is just as silly,
as the GIC distributor supports byte accesses for the GICD_TARGETRn
registers, which when used make the update atomic by definition.
Drop the terminally broken code and replace it by a byte write.
Fixes: 04c8b0f82c ("irqchip/gic: Make locking a BL_SWITCHER only feature")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Anup originally re-spun his patch set to include this fix, but it was a bit too
late for my PR so I've split it out.
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200611175302.253540-1-palmer@dabbelt.com
readx_poll_timeout() can sleep if @sleep_us is specified by the caller,
and is therefore unsafe to be used inside the atomic context, which is
this case when we use it to poll the GICR_VPENDBASER.Dirty bit in
irq_set_vcpu_affinity() callback.
Let's convert to its atomic version instead which helps to get the v4.1
board back to life!
Fixes: 96806229ca ("irqchip/gic-v4.1: Add support for VPENDBASER's Dirty+Valid signaling")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200605052345.1494-1-yuzenghui@huawei.com
Instead of directly calling RISC-V timer interrupt handler from
RISC-V local interrupt conntroller driver, this patch implements
RISC-V timer interrupt as a per-CPU interrupt using per-CPU APIs
of Linux IRQ subsystem.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The RISC-V per-HART local interrupt controller manages software
interrupts, timer interrupts, external interrupts (which are routed
via the platform level interrupt controller) and other per-HART
local interrupts.
We add a driver for the RISC-V local interrupt controller, which
eventually replaces the RISC-V architecture code, allowing for a
better split between arch code and drivers.
The driver is compliant with RISC-V Hart-Level Interrupt Controller
DT bindings located at:
Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt
Co-developed-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
[Palmer: Cleaned up warnings]
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
The plic_find_hart_id() can be useful to other interrupt controller
drivers (such as RISC-V local interrupt driver) so we rename this
function to riscv_of_parent_hartid() and place it in arch directory
along with riscv_of_processor_hartid().
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
This commit:
818e915fba: ("irqchip: Add Loongson HyperTransport Vector support")
Added a MIPS-only driver, but turned on compilation on all other architectures as well:
config LOONGSON_HTVEC
bool "Loongson3 HyperTransport Interrupt Vector Controller"
depends on MACH_LOONGSON64 || COMPILE_TEST
But this driver was never build tested on any other architecture than MIPS:
drivers/irqchip/irq-loongson-htvec.c: In function ‘htvec_irq_dispatch’:
drivers/irqchip/irq-loongson-htvec.c:59:3: error: implicit declaration of function ‘spurious_interrupt’; did you mean ‘smp_reboot_interrupt’? [-Werror=implicit-function-declaration]
Because spurious_interrupt() only exists on MIPS.
So make it MIPS-only.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This controller appears on Loongson LS7A family of PCH to transform
interrupts from PCI MSI into HyperTransport vectorized interrrupts
and send them to procrssor's HT vector controller.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200528152757.1028711-6-jiaxun.yang@flygoat.com
This controller appears on Loongson LS7A family of PCH to transform
interrupts from devices into HyperTransport vectorized interrrupts
and send them to procrssor's HT vector controller.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200528152757.1028711-4-jiaxun.yang@flygoat.com
This controller appears on Loongson-3 chips for receiving interrupt
vectors from PCH's PIC and PCH's PCIe MSI interrupts.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200528152757.1028711-2-jiaxun.yang@flygoat.com
For multiple PLIC instances, the plic_init() is called once for each
PLIC instance. Due to this we have two issues:
1. cpuhp_setup_state() is called multiple times
2. plic_starting_cpu() can crash for boot CPU if cpuhp_setup_state()
is called before boot CPU PLIC handler is available.
Address both issues by only initializing the HP notifiers when
the boot CPU setup is complete.
Fixes: f1ad1133b1 ("irqchip/sifive-plic: Add support for multiple PLICs")
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200518091441.94843-3-anup.patel@wdc.com
For multiple PLIC instances, each PLIC can only target a subset of
CPUs which is represented by "lmask" in the "struct plic_priv".
Currently, the default irq affinity for each PLIC interrupt is all
online CPUs which is illegal value for default irq affinity when we
have multiple PLIC instances. To fix this, we now set "lmask" as the
default irq affinity in for each interrupt in plic_irqdomain_map().
Fixes: f1ad1133b1 ("irqchip/sifive-plic: Add support for multiple PLICs")
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200518091441.94843-2-anup.patel@wdc.com
(E)PPIs are per-CPU interrupts, so we want each CPU to go and enable them
via enable_percpu_irq(); this also means we want IRQ_NOAUTOEN for them as
the autoenable would lead to calling irq_enable() instead of the more
appropriate irq_percpu_enable().
Calling irq_set_percpu_devid() is enough to get just that since it trickles
down to irq_set_percpu_devid_flags(), which gives us IRQ_NOAUTOEN (and a
few others). Setting IRQ_NOAUTOEN *again* right after this call is just
redundant, so don't do it.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200521223500.834-1-valentin.schneider@arm.com
When mapping a LPI, the ITS driver picks the first possible
affinity, which is in most cases CPU0, assuming that if
that's not suitable, someone will come and set the affinity
to something more interesting.
It apparently isn't the case, and people complain of poor
performance when many interrupts are glued to the same CPU.
So let's place the interrupts by finding the "least loaded"
CPU (that is, the one that has the fewer LPIs mapped to it).
So called 'managed' interrupts are an interesting case where
the affinity is actually dictated by the kernel itself, and
we should honor this.
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1575642904-58295-1-git-send-email-john.garry@huawei.com
Link: https://lore.kernel.org/r/20200515165752.121296-3-maz@kernel.org
In order to improve the distribution of LPIs among CPUs, let start by
tracking the number of LPIs assigned to CPUs, both for managed and
non-managed interrupts (as separate counters).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20200515165752.121296-2-maz@kernel.org
A PLIC may not be connected to all the cores. In that case, nr_contexts
may be less than num_possible_cpus. This requirement is only valid a single
PLIC is the only interrupt controller for the whole system.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: "Wesley W. Terpstra" <wesley@sifive.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Link: https://lore.kernel.org/r/20200512172636.96299-1-atish.patra@wdc.com
[Atish: Modified the commit text]
With an SMP configuration, gic_smp_init() calls set_smp_cross_call().
set_smp_cross_call() is marked with "__init".
So gic_smp_init() should also be marked with "__init".
gic_smp_init() is only called from gic_init_bases().
gic_init_bases() is also marked with "__init";
So marking gic_smp_init() with "__init" is fine.
Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200422112857.4300-1-ingo.rohloff@lauterbach.com
Fix the following sparse warning:
drivers/irqchip/irq-bcm7038-l1.c:419:12: warning: symbol
'bcm7038_l1_of_init' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200417074036.46594-1-yanaijie@huawei.com
Fix the following sparse warning:
drivers/irqchip/irq-mvebu-icu.c:69:1: warning: symbol 'legacy_bindings'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200417074046.46771-1-yanaijie@huawei.com
Running a lockedp-enabled kernel on a vim3l board (Amlogic SM1)
leads to the following splat:
[ 13.557138] WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
[ 13.587485] ip/456 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[ 13.625922] ffff000059908cf0 (&irq_desc_lock_class){-.-.}-{2:2}, at: __setup_irq+0xf8/0x8d8
[ 13.632273] which would create a new lock dependency:
[ 13.637272] (&irq_desc_lock_class){-.-.}-{2:2} -> (&ctl->lock){+.+.}-{2:2}
[ 13.644209]
[ 13.644209] but this new dependency connects a HARDIRQ-irq-safe lock:
[ 13.654122] (&irq_desc_lock_class){-.-.}-{2:2}
[ 13.654125]
[ 13.654125] ... which became HARDIRQ-irq-safe at:
[ 13.664759] lock_acquire+0xec/0x368
[ 13.666926] _raw_spin_lock+0x60/0x88
[ 13.669979] handle_fasteoi_irq+0x30/0x178
[ 13.674082] generic_handle_irq+0x38/0x50
[ 13.678098] __handle_domain_irq+0x6c/0xc8
[ 13.682209] gic_handle_irq+0x5c/0xb0
[ 13.685872] el1_irq+0xd0/0x180
[ 13.689010] arch_cpu_idle+0x40/0x220
[ 13.692732] default_idle_call+0x54/0x60
[ 13.696677] do_idle+0x23c/0x2e8
[ 13.699903] cpu_startup_entry+0x30/0x50
[ 13.703852] rest_init+0x1e0/0x2b4
[ 13.707301] arch_call_rest_init+0x18/0x24
[ 13.711449] start_kernel+0x4ec/0x51c
[ 13.715167]
[ 13.715167] to a HARDIRQ-irq-unsafe lock:
[ 13.722426] (&ctl->lock){+.+.}-{2:2}
[ 13.722430]
[ 13.722430] ... which became HARDIRQ-irq-unsafe at:
[ 13.732319] ...
[ 13.732324] lock_acquire+0xec/0x368
[ 13.735985] _raw_spin_lock+0x60/0x88
[ 13.739452] meson_gpio_irq_domain_alloc+0xcc/0x290
[ 13.744392] irq_domain_alloc_irqs_hierarchy+0x24/0x60
[ 13.749586] __irq_domain_alloc_irqs+0x160/0x2f0
[ 13.754254] irq_create_fwspec_mapping+0x118/0x320
[ 13.759073] irq_create_of_mapping+0x78/0xa0
[ 13.763360] of_irq_get+0x6c/0x80
[ 13.766701] of_mdiobus_register_phy+0x10c/0x238 [of_mdio]
[ 13.772227] of_mdiobus_register+0x158/0x380 [of_mdio]
[ 13.777388] mdio_mux_init+0x180/0x2e8 [mdio_mux]
[ 13.782128] g12a_mdio_mux_probe+0x290/0x398 [mdio_mux_meson_g12a]
[ 13.788349] platform_drv_probe+0x5c/0xb0
[ 13.792379] really_probe+0xe4/0x448
[ 13.795979] driver_probe_device+0xe8/0x140
[ 13.800189] __device_attach_driver+0x94/0x120
[ 13.804639] bus_for_each_drv+0x84/0xd8
[ 13.808474] __device_attach+0xe4/0x168
[ 13.812361] device_initial_probe+0x1c/0x28
[ 13.816592] bus_probe_device+0xa4/0xb0
[ 13.820430] deferred_probe_work_func+0xa8/0x100
[ 13.825064] process_one_work+0x264/0x688
[ 13.829088] worker_thread+0x4c/0x458
[ 13.832768] kthread+0x154/0x158
[ 13.836018] ret_from_fork+0x10/0x18
[ 13.839612]
[ 13.839612] other info that might help us debug this:
[ 13.839612]
[ 13.850354] Possible interrupt unsafe locking scenario:
[ 13.850354]
[ 13.855720] CPU0 CPU1
[ 13.858774] ---- ----
[ 13.863242] lock(&ctl->lock);
[ 13.866330] local_irq_disable();
[ 13.872233] lock(&irq_desc_lock_class);
[ 13.878705] lock(&ctl->lock);
[ 13.884297] <Interrupt>
[ 13.886857] lock(&irq_desc_lock_class);
[ 13.891014]
[ 13.891014] *** DEADLOCK ***
The issue can occur when CPU1 is doing something like irq_set_type()
and CPU0 performing an interrupt allocation, for example. Taking
an interrupt (like the one being reconfigured) would lead to a deadlock.
A solution to this is:
- Reorder the locking so that meson_gpio_irq_update_bits takes the lock
itself at all times, instead of relying on the caller to lock or not,
hence making the RMW sequence atomic,
- Rework the critical section in meson_gpio_irq_request_channel to only
cover the allocation itself, and let the gpio_irq_sel_pin callback
deal with its own locking if required,
- Take the private spin-lock with interrupts disabled at all times
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
As per the PLIC specification, maximum priority threshold value is 0x7
not 0xF. Even though it doesn't cause any error in qemu/hifive unleashed,
there may be some implementation which checks the upper bound resulting in
an illegal access.
Fixes: ccbe80bad5 ("irqchip/sifive-plic: Enable/Disable external interrupts upon cpu online/offline")
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200403014609.71831-1-atish.patra@wdc.com
The ti_sci_inta_irq_handler() does not take into account INTA IRQs state
(masked/unmasked) as it uses INTA_STATUS_CLEAR_j register to get INTA IRQs
status, which provides raw status value.
This causes hard IRQ handlers to be called or threaded handlers to be
scheduled many times even if corresponding INTA IRQ is masked.
Above, first of all, affects the LEVEL interrupts processing and causes
unexpected behavior up the system stack or crash.
Fix it by using the Interrupt Masked Status INTA_STATUSM_j register which
provides masked INTA IRQs status.
Fixes: 9f1463b86c ("irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200408191532.31252-1-grygorii.strashko@ti.com
Cc: stable@vger.kernel.org
Using irq_domain_free_irqs_common() on the irqdomain free path will
leave the MSI descriptor unfreed when platform devices get removed.
Properly free it by MSI domain free function.
Fixes: 9650c60ebf ("irqchip/mbigen: Create irq domain for each mbigen device")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200408114352.1604-1-yuzenghui@huawei.com
Although the vSGIs are not directly visible to the host, they still
get moved around by the CPU hotplug, for example. This results in
the kernel moaning on the console, such as:
genirq: irq_chip GICv4.1-sgi did not update eff. affinity mask of irq 38
Updating the effective affinity on set_affinity() fixes it.
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When a vPE is made resident, the GIC starts parsing the virtual pending
table to deliver pending interrupts. This takes place asynchronously,
and can at times take a long while. Long enough that the vcpu enters
the guest and hits WFI before any interrupt has been signaled yet.
The vcpu then exits, blocks, and now gets a doorbell. Rince, repeat.
In order to avoid the above, a (optional on GICv4, mandatory on v4.1)
feature allows the GIC to feedback to the hypervisor whether it is
done parsing the VPT by clearing the GICR_VPENDBASER.Dirty bit.
The hypervisor can then wait until the GIC is ready before actually
running the vPE.
Plug the detection code as well as polling on vPE schedule. While
at it, tidy-up the kernel message that displays the GICv4 optional
features.
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
driver which affected the PPC users.
-----BEGIN PGP SIGNATURE-----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=pZAC
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-04-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two reverts addressing regressions of the Xilinx interrupt controller
driver which affected the PPC users"
* tag 'irq-urgent-2020-04-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "irqchip/xilinx: Enable generic irq multi handler"
Revert "irqchip/xilinx: Do not call irq_set_default_host()"
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early. Most cleanup changes come
through the various maintainer trees, so the final removal of
setup_irq() is postponed towards the end of the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and unsafe
interrupt injection including a fixup of the offending PCI/AER error
injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside of
an actual interrupt, can cause inconsistent state on the fragile
x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place
-----BEGIN PGP SIGNATURE-----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=DZ/G
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early.
Most cleanup changes come through the various maintainer trees, so
the final removal of setup_irq() is postponed towards the end of
the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and
unsafe interrupt injection including a fixup of the offending
PCI/AER error injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside
of an actual interrupt, can cause inconsistent state on the
fragile x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place"
* tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
unicore32: Replace setup_irq() by request_irq()
sh: Replace setup_irq() by request_irq()
hexagon: Replace setup_irq() by request_irq()
c6x: Replace setup_irq() by request_irq()
alpha: Replace setup_irq() by request_irq()
irqchip/gic-v4.1: Eagerly vmap vPEs
irqchip/gic-v4.1: Add VSGI property setup
irqchip/gic-v4.1: Add VSGI allocation/teardown
irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer
irqchip/gic-v4.1: Plumb set_vcpu_affinity SGI callbacks
irqchip/gic-v4.1: Plumb get/set_irqchip_state SGI callbacks
irqchip/gic-v4.1: Plumb mask/unmask SGI callbacks
irqchip/gic-v4.1: Add initial SGI configuration
irqchip/gic-v4.1: Plumb skeletal VSGI irqchip
irqchip/stm32: Retrigger both in eoi and unmask callbacks
irqchip/gic-v3: Move irq_domain_update_bus_token to after checking for NULL domain
irqchip/xilinx: Do not call irq_set_default_host()
irqchip/xilinx: Enable generic irq multi handler
irqchip/xilinx: Fill error code when irq domain registration fails
irqchip/xilinx: Add support for multiple instances
...
This controller appeared on Loongson-3 family of chips to receive
interrupts from PCH PIC.
It is a I8259 with optimized interrupt polling flow. We can poll
interrupt number from HT vector directly but still have to follow
standard I8259 routines to mask, unmask and EOI.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The 1.0 version of that controller has a bug that status bit
of LPC IRQ sometimes doesn't get set correctly.
So we can always blame LPC IRQ when spurious interrupt happens
at the parent interrupt line which LPC IRQ supposed to route
to.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This controller appeared on Loongson family of chips as the primary
package interrupt source.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Now that we have HW-accelerated SGIs being delivered to VPEs, it
becomes required to map the VPEs on all ITSs instead of relying
on the lazy approach that we would use when using the ITS-list
mechanism.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-17-maz@kernel.org
In order to hide some of the differences between v4.0 and v4.1, move
the doorbell management out of the KVM code, and into the GICv4-specific
layer. This allows the calling code to ask for the doorbell when blocking,
and otherwise to leave the doorbell permanently disabled.
This matches the v4.1 code perfectly, and only results in a minor
refactoring of the v4.0 code.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-14-maz@kernel.org
