There is a typo here. It should be "stats" instead of "state". The
impact is that we clear 224 bytes instead of 80 and we zero out memory
that we shouldn't.
Fixes: 09ae5d37e0 ("crypto: zip - Add Compression/Decompression statistics")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The driver uses type of device (variant) only during probe so there is
no need to store it for later.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Driver is capable of handling only one request at a time and it stores
it in its state container struct s5p_aes_dev. This stored request must be
protected between concurrent invocations (e.g. completing current
request and scheduling new one). Combination of lock and "busy" field
is used for that purpose.
When "busy" field is true, the driver will not accept new request thus
it will not overwrite currently handled data.
However commit 28b62b1458 ("crypto: s5p-sss - Fix spinlock recursion
on LRW(AES)") moved some of the write to "busy" field out of a lock
protected critical section. This might lead to potential race between
completing current request and scheduling a new one. Effectively the
request completion might try to operate on new crypto request.
Cc: <stable@vger.kernel.org> # v4.10.x
Fixes: 28b62b1458 ("crypto: s5p-sss - Fix spinlock recursion on LRW(AES)")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support to submit ablkcipher and authenc algorithms
via the QI backend:
-ablkcipher:
cbc({aes,des,des3_ede})
ctr(aes), rfc3686(ctr(aes))
xts(aes)
-authenc:
authenc(hmac(md5),cbc({aes,des,des3_ede}))
authenc(hmac(sha*),cbc({aes,des,des3_ede}))
caam/qi being a new driver, let's wait some time to settle down without
interfering with existing caam/jr driver.
Accordingly, for now all caam/qi algorithms (caamalg_qi module) are
marked to be of lower priority than caam/jr ones (caamalg module).
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM engine supports two interfaces for crypto job submission:
-job ring interface - already existing caam/jr driver
-Queue Interface (QI) - caam/qi driver added in current patch
QI is present in CAAM engines found on DPAA platforms.
QI gets its I/O (frame descriptors) from QMan (Queue Manager) queues.
This patch adds a platform device for accessing CAAM's queue interface.
The requests are submitted to CAAM using one frame queue per
cryptographic context. Each crypto context has one shared descriptor.
This shared descriptor is attached to frame queue associated with
corresponding driver context using context_a.
The driver hides the mechanics of FQ creation, initialisation from its
applications. Each cryptographic context needs to be associated with
driver context which houses the FQ to be used to transport the job to
CAAM. The driver provides API for:
(a) Context creation
(b) Job submission
(c) Context deletion
(d) Congestion indication - whether path to/from CAAM is congested
The driver supports affining its context to a particular CPU.
This means that any responses from CAAM for the context in question
would arrive at the given CPU. This helps in implementing one CPU
per packet round trip in IPsec application.
The driver processes CAAM responses under NAPI contexts.
NAPI contexts are instantiated only on cores with affined portals since
only cores having their own portal can receive responses from DQRR.
The responses from CAAM for all cryptographic contexts ride on a fixed
set of FQs. We use one response FQ per portal owning core. The response
FQ is configured in each core's and thus portal's dedicated channel.
This gives the flexibility to direct CAAM's responses for a crypto
context on a given core.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A few other things need to be added in soc/qman, such that
caam/qi won't open-code them.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Export qman_query_fq_np() function and related structures.
This will be needed in the caam/qi driver, where "queue empty"
condition will be decided based on the frm_cnt.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add and export the ID of the channel serviced by the
CAAM (Cryptographic Acceleration and Assurance Module) DCP.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since qman_volatile_dequeue() is already exported, move the related
structures into the public header too.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The md5_transform function is no longer used any where in the tree,
except for the crypto api's actual implementation of md5, so we can drop
the function from lib and put it as a static function of the crypto
file, where it belongs. There should be no new users of md5_transform,
anyway, since there are more modern ways of doing what it once achieved.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
aes_ctrby8_avx-x86_64.S uses the C preprocessor for token pasting
of character sequences that are not valid preprocessor tokens.
While this is allowed when preprocessing assembler files it exposes
an incompatibilty between the clang and gcc preprocessors where
clang does not strip leading white space from macro parameters,
leading to the CONCAT(%xmm, i) macro expansion on line 96 resulting
in a token with a space character embedded in it.
While this could be resolved by deleting the offending space character,
the assembler is perfectly capable of doing the token pasting correctly
for itself so we can just get rid of the preprocessor macros.
Signed-off-by: Michael Davidson <md@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A version 5 device provides the primitive commands
required for AES GCM. This patch adds support for
en/decryption.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Incorporate 384-bit and 512-bit hashing for a version 5 CCP
device
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
vpmsum implementations often don't kick in for short test vectors.
This is a simple test module that does a configurable number of
random tests, each up to 64kB and each with random offsets.
Both CRC-T10DIF and CRC32C are tested.
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
T10DIF is a CRC16 used heavily in NVMe.
It turns out we can accelerate it with a CRC32 library and a few
little tricks.
Provide the accelerator based the refactored CRC32 code.
Cc: Anton Blanchard <anton@samba.org>
Thanks-to: Hong Bo Peng <penghb@cn.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When CRC32c was included in the kernel, Anton ripped out
the #ifdefs around reflected polynomials, because CRC32c
is always reflected. However, not all CRCs use reflection
so we'd like to make it optional.
Restore the REFLECT parts from Anton's original CRC32
implementation (https://github.com/antonblanchard/crc32-vpmsum)
That implementation is available under GPLv2+, so we're OK
from a licensing point of view:
https://github.com/antonblanchard/crc32-vpmsum/blob/master/LICENSE.TXT
As CRC32c requires REFLECT, add that #define.
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The core nuts and bolts of the crc32c vpmsum algorithm will
also work for a number of other CRC algorithms with different
polynomials. Factor out the function into a new asm file.
To handle multiple users of the function, a user simply
provides constants, defines the name of their CRC function,
and then #includes the core algorithm file.
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This BUG_ON() triggered for me once at shutdown, and I don't see a
reason for the check. The code correctly checks whether the swap slot
cache is usable or not, so an uninitialized swap slot cache is not
actually problematic afaik.
I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since
I'm not sure why that seemingly pointless check was there. I suspect
the real fix is to just remove it entirely, but for now we'll warn about
it but not bring the machine down.
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Wire up statx() syscall
- Don't print a warning on memory hotplug when HPT resizing isn't available
Thanks to:
David Gibson, Chandan Rajendra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TfiW
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc fixes from Michael Ellerman:
"A couple of minor powerpc fixes for 4.11:
- wire up statx() syscall
- don't print a warning on memory hotplug when HPT resizing isn't
available
Thanks to: David Gibson, Chandan Rajendra"
* tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Don't give a warning when HPT resizing isn't available
powerpc: Wire up statx() syscall
Pull parisc fixes from Helge Deller:
- Mikulas Patocka added support for R_PARISC_SECREL32 relocations in
modules with CONFIG_MODVERSIONS.
- Dave Anglin optimized the cache flushing for vmap ranges.
- Arvind Yadav provided a fix for a potential NULL pointer dereference
in the parisc perf code (and some code cleanups).
- I wired up the new statx system call, fixed some compiler warnings
with the access_ok() macro and fixed shutdown code to really halt a
system at shutdown instead of crashing & rebooting.
* 'parisc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix system shutdown halt
parisc: perf: Fix potential NULL pointer dereference
parisc: Avoid compiler warnings with access_ok()
parisc: Wire up statx system call
parisc: Optimize flush_kernel_vmap_range and invalidate_kernel_vmap_range
parisc: support R_PARISC_SECREL32 relocation in modules
Pull SCSI target fixes from Nicholas Bellinger:
"The bulk of the changes are in qla2xxx target driver code to address
various issues found during Cavium/QLogic's internal testing (stable
CC's included), along with a few other stability and smaller
miscellaneous improvements.
There are also a couple of different patch sets from Mike Christie,
which have been a result of his work to use target-core ALUA logic
together with tcm-user backend driver.
Finally, a patch to address some long standing issues with
pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
which will make folks using physical (or virtual) magnetic tape happy"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
qla2xxx: Update driver version to 9.00.00.00-k
qla2xxx: Fix delayed response to command for loop mode/direct connect.
qla2xxx: Change scsi host lookup method.
qla2xxx: Add DebugFS node to display Port Database
qla2xxx: Use IOCB interface to submit non-critical MBX.
qla2xxx: Add async new target notification
qla2xxx: Export DIF stats via debugfs
qla2xxx: Improve T10-DIF/PI handling in driver.
qla2xxx: Allow relogin to proceed if remote login did not finish
qla2xxx: Fix sess_lock & hardware_lock lock order problem.
qla2xxx: Fix inadequate lock protection for ABTS.
qla2xxx: Fix request queue corruption.
qla2xxx: Fix memory leak for abts processing
qla2xxx: Allow vref count to timeout on vport delete.
tcmu: Convert cmd_time_out into backend device attribute
tcmu: make cmd timeout configurable
tcmu: add helper to check if dev was configured
target: fix race during implicit transition work flushes
target: allow userspace to set state to transitioning
target: fix ALUA transition timeout handling
...
Pull device-dax fixes from Dan Williams:
"The device-dax driver was not being careful to handle falling back to
smaller fault-granularity sizes.
The driver already fails fault attempts that are smaller than the
device's alignment, but it also needs to handle the cases where a
larger page mapping could be established. For simplicity of the
immediate fix the implementation just signals VM_FAULT_FALLBACK until
fault-size == device-alignment.
One fix is for -stable to address pmd-to-pte fallback from the
original implementation, another fix is for the new (introduced in
4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the
ride.
These have received a build success notification from the kbuild
robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix debug output typo
device-dax: fix pud fault fallback handling
device-dax: fix pmd/pte fault fallback handling
Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.
Following commands are being routed through IOCB interface
- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The main lock that needs to be held for CMD or TMR submission
to upper layer is the sess_lock. The sess_lock is used to
serialize cmd submission and session deletion. The addition
of hardware_lock being held is not necessary. This patch removes
hardware_lock dependency from CMD/TMR submission.
Use hardware_lock only for error response in this case.
Path1
CPU0 CPU1
---- ----
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
Path2/deadlock
*** DEADLOCK ***
Call Trace:
dump_stack+0x85/0xc2
print_circular_bug+0x1e3/0x250
__lock_acquire+0x1425/0x1620
lock_acquire+0xbf/0x210
_raw_spin_lock_irqsave+0x53/0x70
qlt_sess_work_fn+0x21d/0x480 [qla2xxx]
process_one_work+0x1f4/0x6e0
Cc: <stable@vger.kernel.org>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reported-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Normally, ABTS is sent to Target Core as Task MGMT command.
In the case of error, qla2xxx needs to send response, hardware_lock
is required to prevent request queue corruption.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of putting cmd_time_out under ../target/core/user_0/foo/control,
which has historically been used by parameters needed for initial
backend device configuration, go ahead and move cmd_time_out into
a backend device attribute.
In order to do this, tcmu_module_init() has been updated to create
a local struct configfs_attribute **tcmu_attrs, that is based upon
the existing passthrough_attrib_attrs along with the new cmd_time_out
attribute. Once **tcm_attrs has been setup, go ahead and point
it at tcmu_ops->tb_dev_attrib_attrs so it's picked up by target-core.
Also following MNC's previous change, ->cmd_time_out is stored in
milliseconds but exposed via configfs in seconds. Also, note this
patch restricts the modification of ->cmd_time_out to before +
after the TCMU device has been configured, but not while it has
active fabric exports.
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A single daemon could implement multiple types of devices
using multuple types of real devices that may not support
restarting from crashes and/or handling tcmu timeouts. This
makes the cmd timeout configurable, so handlers that do not
support it can turn if off for now.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This adds a helper to check if the dev was configured. It
will be used in the next patch to prevent updates to some
config settings after the device has been setup.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
-----BEGIN PGP SIGNATURE-----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=lNoR
-----END PGP SIGNATURE-----
Merge tag 'openrisc-for-linus' of git://github.com/openrisc/linux
Pull OpenRISC fixes from Stafford Horne:
"OpenRISC fixes for build issues that were exposed by kbuild robots
after 4.11 merge. All from allmodconfig builds. This includes:
- bug in the handling of 8-byte get_user() calls
- module build failure due to multile missing symbol exports"
* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
openrisc: Export symbols needed by modules
openrisc: fix issue handling 8 byte get_user calls
openrisc: xchg: fix `computed is not used` warning
This fixes the following races:
1. core_alua_do_transition_tg_pt could have read
tg_pt_gp_alua_access_state and gone into this if chunk:
if (!explicit &&
atomic_read(&tg_pt_gp->tg_pt_gp_alua_access_state) ==
ALUA_ACCESS_STATE_TRANSITION) {
and then core_alua_do_transition_tg_pt_work could update the
state. core_alua_do_transition_tg_pt would then only set
tg_pt_gp_alua_pending_state and the tg_pt_gp_alua_access_state would
not get updated with the second calls state.
2. core_alua_do_transition_tg_pt could be setting
tg_pt_gp_transition_complete while the tg_pt_gp_transition_work
is already completing. core_alua_do_transition_tg_pt then waits on the
completion that will never be called.
To handle these issues, we just call flush_work which will return when
core_alua_do_transition_tg_pt_work has completed so there is no need
to do the complete/wait. And, if core_alua_do_transition_tg_pt_work
was running, instead of trying to sneak in the state change, we just
schedule up another core_alua_do_transition_tg_pt_work call.
Note that this does not handle a possible race where there are multiple
threads call core_alua_do_transition_tg_pt at the same time. I think
we need a mutex in target_tg_pt_gp_alua_access_state_store.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Userspace target_core_user handlers like tcmu-runner may want to set the
ALUA state to transitioning while it does implicit transitions. This
patch allows that state when set from configfs.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The implicit transition time tells initiators the min time
to wait before timing out a transition. We currently schedule
the transition to occur in tg_pt_gp_implicit_trans_secs
seconds so there is no room for delays. If
core_alua_do_transition_tg_pt_work->core_alua_update_tpg_primary_metadata
needs to write out info to a remote file, then the initiator can
easily time out the operation.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If tcmu-runner is processing a STPG and needs to change the kernel's
ALUA state then we cannot use the same work queue for task management
requests and ALUA transitions, because we could deadlock. The problem
occurs when a STPG times out before tcmu-runner is able to
call into target_tg_pt_gp_alua_access_state_store->
core_alua_do_port_transition -> core_alua_do_transition_tg_pt ->
queue_work. In this case, the tmr is on the work queue waiting for
the STPG to complete, but the STPG transition is now queued behind
the waiting tmr.
Note:
This bug will also be fixed by this patch:
http://www.spinics.net/lists/target-devel/msg14560.html
which switches the tmr code to use the system workqueues.
For both, I am not sure if we need a dedicated workqueue since
it is not a performance path and I do not think we need WQ_MEM_RECLAIM
to make forward progress to free up memory like the block layer does.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We do not setup the LU group for pscsi devices, so if you write
a state to alua_access_state that will cause a transition you will
get a NULL pointer dereference.
This patch will fail attempts to try and transition the path
for backend devices that set the TRANSPORT_FLAG_PASSTHROUGH_ALUA
flag.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
