Access to some registers depends on register access mode
Three different modes are available for OMAP (at least)
• Operational mode LCR_REG[7] = 0x0
• Configuration mode A LCR_REG[7] = 0x1 and LCR_REG[7:0]! = 0xBF
• Configuration mode B LCR_REG[7] = 0x1 and LCR_REG[7:0] = 0xBF
Define access modes and remove redefinitions and magic numbers
in serial drivers (and later in bluetooth driver).
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define MDR1 register serial definitions used in serial and
bluetooth drivers.
Change magic number to ones defined in serial_reg for omap1/2
serial driver.
Remove redefined MDR1 register definitions in omap-serial driver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Craneboard is a hardware development platform based on the
Sitara AM3517 ARM Cortex - A8 microprocessor device. This is a
low cost reference design.
This patch adds basic board file. Detailed support will follow in
subsequent patches.
[1] http://www.ti.com/arm
[2] http://www.mistralsolutions.com/products/craneboard.php
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patches removes a config option that was used to select a FIQ
handler to be build for Amstrad Delta, as required by the on-board serio
interface driver. Not having any problem reports received since it was
introduced in 2.6.35, the FIQ handler can now be built and initialized by
default, thus reqiring no extra config option.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It's easier to understand what that number means and
also avoids problems if we ever have to change it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
They are extremely similar anyway, let's get rid
of one file.
While at that, also remove the empty zoom_config
variable.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The changes are:
- Use 'for' loop instead 'while' loop.
- No need to initialize ret to 0, we're assigning it right after.
- No need to check for onenandcs < GPMC_CS_NUM here, it will always be true.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_board_config_size is implicitly initialized to 0 in
plat-omap/common.c, get_config() won't dereference omap_board_config,
so we can remove the empty igep2_config array.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
for the epson frambuffer support it's CONFIG_FB_S1D13XXX
not CONFIG_FB_S1D135XX
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
to be a few more concistant with the other boards
as ek is for evaluation kit and dk for development kit
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
- Ajeco 1ARM Single Board Computer
- Sperry-Sun KAFA board
- picotux 200
Remove the deprecated at91_init_serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Currently, the kprobes implementation for ARM only supports the ARM
instruction set, so it only works if CONFIG_THUMB2_KERNEL is not
enabled.
Until kprobes is updated to work with Thumb-2, turning it on will
cause horrible things to happen, so this patch disables it for now.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a
result, using these directives in code sections can result in
misaligned data words when building a Thumb-2 kernel
(CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to
assume that fundamental types of word size or above are word-
aligned when accessing them from C. If the data is not really
word-aligned, this can cause impaired performance and stray
alignment faults in some circumstances.
In general, the following rules should be applied when using
data word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned data
words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume that
fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned, this
can cause impaired performance and stray alignment faults in some
circumstances.
In general, the following rules should be applied when using data word
declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 32-bit conditional branches in Thumb-2 have a shorter range
(+/-512K) than their ARM counterparts (+/-32MB). The linker does
not currently generate trampolines to extend the range of these
Thumb-2 conditional branches, resulting in link errors when vmlinux
is sufficiently large, e.g.:
head.o:(.text+0x464): relocation truncated to fit: R_ARM_THM_JUMP19
This patch forces the longer-range, unconditional branch encoding
by use of an explicit IT instruction. The resulting branches are
triggered on the same conditions as before.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code which makes up the zImage header intends to leave a
32-byte gap followed by a branch to the real entry point, a magic
number, and a word containing the absolute entry point address.
This gets messed up with with CONFIG_THUMB2_KERNEL, because the
size of the initial padding NOPs changes.
Instead, the header can be made fully compatible by restoring it to
ARM.
In the Thumb-2 case, we can replace the initial NOPs with a
sequence which switches to Thumb and jumps to the real entry point.
As a consequence, the zImage entry point is now always ARM, so no
special magic is needed any more for the uImage rules in the
Thumb-2 case.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some instruction operand combinations are used here which are nor
permitted in Thumb-2.
In particular, most uses of pc as an operand are disallowed in
Thumb-2, and deprecated in ARM from ARMv7 onwards.
The modified code introduced by this patch should be compatible
with all architecture versions >= v3, with or without
CONFIG_THUMB2_KERNEL.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
In this specific case, we can achieve the desired alignment by
forcing a 32-bit branch instruction using the W() macro, since the
assembler location counter is already 32-bit aligned in this case.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change limits number of GIC-originating interrupts to the
platform maximum (defined by NR_IRQS) while still initialising
all distributor registers.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Rafael Gandolfi <kaillasse91@hotmail.fr>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
RTC clock will remain at 32KHz and powered on, there is no need for it
at this moment.
Signed-off-by: Jason Chagas <jason.chagas@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
About all options present in each file are activated
in the single file.
Signed-off-by: Eric Benard <eric@eukrea.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Dependency on (CPU_S3C2416 is not selected) was defined as "!CPU_2416",
instead of "!CPU_S3C2416". Fix it.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Enable compilation of platform devices and initialization code used in
SMDK2416 board file.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2+: PM/serial: hold console semaphore while OMAP UARTs are disabled
OMAP: UART: don't resume UARTs that are not enabled.
commit 6338a6aa7c ("ARM: 6269/1: Add 'code'
parameter for hook_fault_code()") breaks CNS3xxx build:
CC arch/arm/mach-cns3xxx/pcie.o
pcie.c: In function 'cns3xxx_pcie_init':
pcie.c:373: warning: passing argument 4 of 'hook_fault_code' makes integer from pointer without a cast
pcie.c:373: error: too few arguments to function 'hook_fault_code'
This commit fixes the small issue.
Cc: stable@kernel.org [36]
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch fixes following warning messages when CONFIG_PM selected.
In file included from arch/arm/mach-s5pv210/mach-smdkv210.c:34:
arch/arm/plat-samsung/include/plat/pm.h:104: warning: 'struct sys_device'
declared inside parameter list
arch/arm/plat-samsung/include/plat/pm.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want
arch/arm/plat-samsung/include/plat/pm.h:105: warning: 'struct sys_device'
declared inside parameter list
In file included from arch/arm/mach-s5pv210/mach-smdkc110.c:31:
arch/arm/plat-samsung/include/plat/pm.h:104: warning: 'struct sys_device'
declared inside parameter list
arch/arm/plat-samsung/include/plat/pm.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want
arch/arm/plat-samsung/include/plat/pm.h:105: warning: 'struct sys_device'
declared inside parameter list
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The UART3 submask should be 0x7 (SUBSRCPND[26:24]).
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
IRQ_S3C2443_UART3 is being used as the base when it should actually
be IRQ_S3C2443_RX3 on S3C2443 and S3C2416 for the UART3.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Don't rewrite clock config in UCON preconfigured by
bootloader. No need to set 10th bit in UCON because
[11:10] 2'b00 means source clock is PCLK too.
If set, console does not work if bootloader
has preconfigured [11:10] with 2'b00.
If not set, console works with any bootloader
config value (2'bxx).
More information about clock setup in UCON is available
in "S3C6410X RISC Microprocessor User's Manual,
Revision 1.20" p. 31-13 (Chapter 31.6.2
UART CONTROL REGISTER).
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Replace in s3c_gpio_cfgpull with s3c_gpio_setpull.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use IOMEM() macro to get rid of the following sparse warning:
arch/arm/mach-omap1/board-ams-delta.c:319:36: warning: incorrect type in initializer (different address spaces)
arch/arm/mach-omap1/board-ams-delta.c:319:36: expected void [noderef] <asn:2>*membase
arch/arm/mach-omap1/board-ams-delta.c:319:36: got void *<noident>
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make some variables static to get rid of the following warnings:
arch/arm/mach-omap1/mailbox.c:136:18: warning: symbol 'mbox_dsp_info' was not declared. Should it be static?
arch/arm/mach-omap1/mailbox.c:142:18: warning: symbol 'omap1_mboxes' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make some functions static to get rid of the following sparse warnings:
arch/arm/mach-omap1/mcbsp.c:177:12: warning: symbol 'omap1_mcbsp_init' was not declared. Should it be static?
arch/arm/mach-omap1/mux.c:346:22: warning: symbol 'omap1_cfg_reg' was not declared. Should it be static?
arch/arm/plat-omap/dma.c:177:5: warning: symbol 'omap_dma_in_1510_mode' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:273:12: warning: symbol 'omap1_sram_init' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing includes to get rid of the following sparse warnings:
arch/arm/mach-omap1/devices.c:225:13: warning: symbol 'omap1_camera_init' was not declared. Should it be static?
arch/arm/mach-omap1/flash.c:15:6: warning: symbol 'omap1_set_vpp' was not declared. Should it be static?
arch/arm/mach-omap1/serial.c:190:6: warning: symbol 'omap_serial_wake_trigger' was not declared. Should it be static?
arch/arm/mach-omap1/time.c:252:18: warning: symbol 'omap_timer' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The console semaphore must be held while the OMAP UART devices are
disabled, lest a console write cause an ARM abort (and a kernel crash)
when the underlying console device is inaccessible. These crashes
only occur when the console is on one of the OMAP internal serial
ports.
While this problem has been latent in the PM idle loop for some time,
the crash was not triggerable with an unmodified kernel until commit
6f251e9db1 ("OMAP: UART: omap_device
conversions, remove implicit 8520 assumptions"). After this patch, a
console write often occurs after the console UART has been disabled in
the idle loop, crashing the system. Several users have encountered
this bug:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg38396.htmlhttp://www.mail-archive.com/linux-omap@vger.kernel.org/msg36602.html
The same commit also introduced new code that disabled the UARTs
during init, in omap_serial_init_port(). The kernel will also crash
in this code when earlyconsole and extra debugging is enabled:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg36411.html
The minimal fix for the -rc series is to hold the console semaphore
while the OMAP UARTs are disabled. This is a somewhat overbroad fix,
since the console may not be located on an OMAP UART, as is the case
with the GPMC UART on Zoom3. While it is technically possible to
determine which devices the console or earlyconsole is actually
running on, it is not a trivial problem to solve, and the code to do
so is not really appropriate for the -rc series.
The right long-term fix is to ensure that no code outside of the OMAP
serial driver can disable an OMAP UART. As I understand it, code to
implement this is under development by TI.
This patch is a collaboration between Paul Walmsley <paul@pwsan.com>
and Tony Lindgren <tony@atomide.com>. Thanks to Ming Lei
<tom.leiming@gmail.com> and Pramod <pramod.gurav@ti.com> for their
feedback on earlier versions of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Pramod <pramod.gurav@ti.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Add additional check to omap_uart_resume_idle() so that only
enabled (specifically, idle-enabled) UARTs are allowed to resume.
This matches the existing check in prepare idle.
Without this patch, the system will hang if a board is
configured to register only some uarts instead of all of
them and PM is enabled.
Cc: Govindraj R. <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: clkfwk: Build fix for non-legacy CPG changes.
sh: Use GCC __builtin_prefetch() to implement prefetch().
sh: fix vsyscall compilation due to .eh_frame issue
sh: avoid to flush all cache in sys_cacheflush
sh: clkfwk: Disable init clk op for non-legacy clocks.
sh: clkfwk: Kill off now unused algo_id in set_rate op.
sh: clkfwk: Kill off unused clk_set_rate_ex().
The find_next_bit, find_first_bit, find_next_zero_bit
and find_first_zero_bit functions were not properly
clamping to the maxbit argument at the bit level. They
were instead only checking maxbit at the byte level.
To fix this, add a compare and a conditional move
instruction to the end of the common bit-within-the-
byte code used by all the functions and be sure not to
clobber the maxbit argument before it is used.
Cc: <stable@kernel.org>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: James Jones <jajones@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PLLC2 clock was utilizing the same sort of enable/disable without
regard to usecount approach that the FSIDIV clock was when being used as
a PLL pass-through. This forces the enable/disable through the clock
framework, which now prevents the clock from being ripped out or modified
underneath users that have an existing handle on it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current AP4 FSI didn't use set_rate for ak4642,
and used dummy rate when init.
And FSI driver was modified to always call set_rate.
The user which are using FSI set_rate is only AP4 now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current AP4 FSI set_rate function used bogus clock process
which didn't care enable/disable and clk->usecound.
To solve this issue, this patch also modify FSI driver to call
set_rate with enough options.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current FSIDIV clock framework had bogus disable.
This patch remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (41 commits)
ALSA: hda - Identify more variants for ALC269
ALSA: hda - Fix wrong ALC269 variant check
ALSA: hda - Enable jack sense for Thinkpad Edge 11
ALSA: Revert "ALSA: hda - Fix switching between dmic and mic using the same mux on IDT/STAC"
ALSA: hda - Fixed ALC887-VD initial error
ALSA: atmel - Fix the return value in error path
ALSA: hda: Use hp-laptop quirk to enable headphones automute for Asus A52J
ALSA: snd-atmel-abdac: test wrong variable
ALSA: azt3328: period bug fix (for PA), add missing ACK on stop timer
ALSA: hda: Add Samsung R720 SSID for subwoofer pin fixup
ALSA: sound/pci/asihpi/hpioctl.c: Remove unnecessary casts of pci_get_drvdata
ALSA: sound/core/pcm_lib.c: Remove unnecessary semicolons
ALSA: sound/ppc: Use printf extension %pR for struct resource
ALSA: ac97: Apply quirk for Dell Latitude D610 binding Master and Headphone controls
ASoC: uda134x - set reg_cache_default to uda134x_reg
ASoC: Add support for MAX98089 CODEC
ASoC: davinci: fixes for multi-component
ASoC: Fix register cache setup WM8994 for multi-component
ASoC: Fix dapm_seq_compare() for multi-component
ASoC: RX1950: Fix hw_params function
...
init_mm used at kernel/sched.c:idle_task_exit() has spin_lock
(init_mm.context.id_lock) that is not initialized when spin_lock/unlock
is called at an ARM machine. Note that mm_struct.context.id_lock is
usually initialized except for the instance of init_mm at
linux/arch/arm/mm/context.c
Not initializing this spinlock incurs "BUG: pinlock bad magic"
warning when spinlock debug is enabled. We have observed such
instances when testing PM in S5PC210 machines.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adding KERN_WARNING in the middle of strings now produces those tokens
in the output, rather than accepting the level as was once the case.
Fix this in the one reported case. There might be more...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We now:
* check for a v3 controller before setting 8-bit bus width
* offer a callback for platform code to switch to 8-bit mode, which
allows non-v3 controllers to support it
* rely on mmc->caps |= MMC_CAP_8_BIT_DATA; in platform code to specify
that the board designers have indeed brought out all the pins for
8-bit to the slot.
We were previously relying only on whether the *controller* supported
8-bit, which doesn't tell us anything about the pin configuration in
the board design.
This fixes the MMC card regression reported by Maxim Levitsky here:
http://thread.gmane.org/gmane.linux.kernel.mmc/4336
by no longer assuming that 8-bit works by default.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The .stack section doesn't contain any contents, and doesn't require
initialization either. Rather than marking the output section with
'NOLOAD' but still having it exist in the object files, mark it with
%nobits which avoids the assembler marking the section with 'CONTENTS'.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 8b592783 added a Thumb-2 variant of usracc which, when it is
called with \rept=2, calls usraccoff once with an offset of 0 and
secondly with a hard-coded offset of 4 in order to avoid incrementing
the pointer again. If \inc != 4 then we will store the data to the wrong
offset from \ptr. Luckily, the only caller that passes \rept=2 to this
function is __clear_user so we haven't been actively corrupting user data.
This patch fixes usracc to pass \inc instead of #4 to usraccoff
when it is called a second time.
Cc: <stable@kernel.org>
Reported-by: Tony Thompson <tony.thompson@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current implementation of sched_clock() for the Nomadik
family is based on the clock source that will wrap around without
any compensation. Currently on the Ux500 after 1030 seconds.
Utilize cnt32_to_63 to expand the sched_clock() counter to 63
bits and introduce a keepwarm() timer to assure that sched clock
and this cnt32_to_63 is called atleast once every half period.
When I print out the actual wrap-around time, and using
a year (3600*24*365 seconds) as minumum wrap limit I get an
actual wrap-around of:
sched_clock: using 55 bits @ 8333125 Hz wrap in 416 days
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 7c63984b86 (ARM: do not define VMALLOC_END relative to PAGE_OFFSET)
changed VMALLOC_END to be an explicit value. Before this, it was
relative to PAGE_OFFSET and therefore converted to unsigned long
as PAGE_OFFSET is an unsigned long. This introduced the following
build warning. Fix this by changing the explicit defines of
VMALLOC_END to be unsigned long.
CC arch/arm/mm/init.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Uwe Kleine-K <u.kleine-koenig@pengutronix.dee>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change updates the ux500 specific outer cache code to use
the new *_relaxed() I/O accessors.
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the compiler to better optimize the page table walking code
by avoiding over-complex pmd_addr_end() calculations. These
calculations prevent the compiler spotting that we'll never iterate
over the PMD table, causing it to create double nested loops where
a single loop will do.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a MSTP assignment problem in the sh7372 clock
framework code. The USB drivers should attach to
MSTP322 not MSTP33 where IIC1 is located.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Multi-component commit f0fba2ad broke a few things which this patch should
fix. Tested on the DM355 EVM. I've been as careful as I can, but it would be
good if those with access to other Davinci boards could test.
--
The multi-component commit put the initialisation of
snd_soc_dai.[capture|playback]_dma_data into snd_soc_dai_ops.hw_params of the
McBSP, McASP & VCIF drivers (davinci-i2s.c, davinci-mcasp.c & davinci-vcif.c).
The initialisation had to be moved from the probe function in these drivers
because davinci_*_dai changed from snd_soc_dai to snd_soc_dai_driver.
Unfortunately, the DMA params pointer is needed by davinci_pcm_open (in
davinci-pcm.c) before hw_params is called. I have moved the initialisation to
a new snd_soc_dai_ops.startup function in each of these drivers. This fix
indicates that all platforms that use davinci-pcm must have been broken and
need to test with this fix.
--
The multi-component commit also changed the McBSP driver name from
"davinci-asp" to "davinci-i2s" in davinci-i2s.c without updating the board
level references to the driver name. This change is understandable, as there
is a similarly named "davinci-mcasp" driver in davinci-mcasp.c.
There is probably no 'correct' name for this driver. The DM6446 datasheet
calls it the "ASP" and describes it as a "specialised McBSP". The DM355
datasheet calls it the "ASP" and describes it as a "specialised ASP". The
DM365 datasheet calls it the "McBSP". Rather than fix this problem by
reverting to "davinci-asp", I've elected to avoid future confusion with the
"davinci-mcasp" driver by changing it to "davinci-mcbsp", which is also
consistent with the names of the functions in the driver. There are other
fixes required, so it was never going to be as simple as a revert anyway.
--
The DM365 only has one McBSP port (of the McBSP platforms, only the DM355 has
2 ports), so I've changed the the id of the platform_device from 0 to -1.
--
In davinci-evm.c, the DM6446 EVM can no longer share a snd_soc_dai_link
structure with the DM355 EVM as they use different cpu DAI names (the DM355
has 2 ports and the EVM uses the second port, but the DM6446 only has 1 port).
This also means that the 2 boards need different snd_soc_card structures.
--
The codec_name entries in davinci-evm.c didn't match the i2c ids in the board
files. I have only checked and fixed the details of the names used for the
McBSP based platforms. Someone with a McASP based platform (eg DA8xx) should
check the others.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Removed mux: and added the __func__ macro to make debugging
easier.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The mux framework allows the change of pad configuration by drivers
when needed. Prior to this the mux framework has to be initialised
with all the mux parameters specific to the board. The mux init is
already present in the board file for SDP. Adding the mux init
for panda boards.
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Select the CBS package if SDP4430 is enabled during config.
Use the proper package (CBL or CBS) based on chip revision.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Please note that the full muxmodes are re-defined for ES2 instead
of using the subset. There are 81 differences among 204 pins.
The subset fixup will have to iterate over the whole list for each
subset entry, which can lead to an important number of iteration.
On the other hand, it will take much more memory at boot time.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Select the CBL package if SDP4430 is enabled during config.
Initialize the mux framework during the board init.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Add data for OMAP4430 generated from HW pinout & register database.
The data set is split in two partitions for both core and wkup.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Starting on OMAP4, the pin mux configuration is located in two
different partitions of the control module (CODE_PAD and WKUP_PAD).
The first one is inside the core power domain whereas the second
one is inside the wakeup.
- Add the capability to add any number of partition during board init
time depending of Soc partitioning.
- Add some init flags as well in order to avoid explicit Soc version
check inside the mux core code.
- Add a comment with mux0 mode on top of omap_mux/board/<partition>
if the current mux mode is not the default one.
Thanks to Tony Lindgren <tony@atomide.com> for the following improvements:
- Add omap_mux_get for getting the partition data so platform level
device code can use it.
- Fix the rx51 board code to use the new API.
- Do not store the partition for each mux entry. Look up the partition
for debugfs instead.
Thanks to Dan Murphy <dmurphy@ti.com> for testing on OMAP4 and reporting
a couple of bugs.
Thanks to Anand Gadiyar <gadiyar@ti.com> for testing on OMAP3 zoom and
bug report.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Murphy Dan <dmurphy@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Replace all the printk(KERN_XXX... with pr_xxx macros.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arm: omap1: devices: need to return with a value
OMAP1: camera.h: add missing include
omap: dma: Add read-back to DMA interrupt handler to avoid spuriousinterrupts
OMAP2: Devkit8000: Fix mmc regulator failure
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: intc: Fix up build failure introduced by radix tree changes.
MAINTAINERS: update the sh git tree entry.
sh: clkfwk: fix up compiler warnings.
sh: intc: Fix up initializers for gcc 4.5.
rtc: rtc-sh - fix a memory leak
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: ap4evb: add fsib 44100Hz rate
MAINTAINERS: update the ARM SH-Mobile git tree entry.
ARM: mach-shmobile: ap4evb: Mark NOR boot loader partitions read-only.
ARM: mach-shmobile: intc-sh7372: fix interrupt number
Now that clk_set_rate_ex() is gone, there is also no way to get at rate
setting algo id, which is now also completely unused. Kill it off before
new clock ops start using it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 35bab0589b (ARM: imx: change the way
spi-imx devices are registered) contained a typo in mx25, leading to link time
failure.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Currently compilation breaks for the eukrea mbimx27 baseboard
when CONFIG_SPI_IMX is selected and CONFIG_TOUCHSCREEN_ADS7846
is not selected. Fix this by removing the ifdefs altogether.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Benard <eric@eukrea.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: GIC: don't disable software generated interrupts
ARM: 6472/1: vexpress ct-ca9x4: only set twd_base if local timers are being used
ARM: arch/arm/kernel/traps.c: Convert sprintf_symbol to %pS
ARM: arch/arm/kernel/hw_breakpoint.c: Convert WARN_ON to WARN
ARM: 6462/1: EP93xx: Document DMA M2P API
ARM: 6470/1: atomic64: use generic implementation for OABI configurations
ARM: 6469/1: perf-events: squash compiler warning
ARM: 6468/1: backtrace: fix calculation of thread stack base
ARM: Fix DMA coherent allocator alignment
ARM: orion5x/kirkwood/mv78xx0: fix MPP configuration corner cases
[ARM] TS-78xxx NAND resource type should be IORESOURCE_MEM
ARM: pxa/saar: fix the building failure caused by typo
ARM: pxa/cm-x2xx: remove duplicate call to pxa27x_init_irq
ARM: pxa: fix the missing definition of IRQ_BOARD_END
ARM: mmp: fix cpuid detection on mmp2
[ARM] Kirkwood: restrict the scope of the PCIe reset workaround
[ARM] Kirkwood: fix timer initialization for LaCie boards
[ARM] Kirkwood: enhance TCLK detection
Software generated interrupts (SGI) are used for IPIs by the kernel.
While previous revisions of the GIC hardware were specified not to
implement enable bits for SGIs, more recent hardware is now permitted
to implement these bits in a per-CPU banked register.
The priority registers for the PPI and SGIs are also per-CPU banked
registers, so ensure that these are also appropriately initialized.
Reported-by: Scott Valentine <svalentine@concentris-systems.com>
Acked-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a big revert of a lot of -rc1 tidspbridge patches in order to
get the driver back into a working state. It also includes a OMAP patch
that was approved by the OMAP maintainer.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also, don't be picky about the location, which incidentally fixes the
build since MEMBLOCK_REAL_LIMIT is gone on 2.6.37.
arch/arm/plat-omap/devices.c: In function 'omap_dsp_reserve_sdram_memblock':
arch/arm/plat-omap/devices.c:287: error: 'MEMBLOCK_REAL_LIMIT'
undeclared (first use in this function)
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
In commit bde28b84, I made the assumption that CONFIG_SMP is always set
for the quad-core ct-ca9x4 platform. As it turns out, people who aren't
using the SMP goodness are confronted with a build failure.
This patch fixes this issue by ensure that twd_base is only set if
local timers are being used (and therefore SMP support is configured).
Reported-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split the OMAP1 and OMAP2+ platform_device build and register code.
Convert the OMAP2+ variant to use omap_device.
This patch was developed in collaboration with Rajendra Nayak
<rnayak@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add hwmod structures for I2C controllers on OMAP3430.
This patch was developed in collaboration with Paul Walmsley
<paul@pwsan.com>.
OMAP3 fixes for correct IDLEST bit monitoring from
G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add hwmod structures for I2C controllers on OMAP2420/2430.
NOTE: I2C module on OMAP2420 has 16bit registers and causes imprecise
aborts if 32bits are read/written to it. Use the HWMOD_16BIT_REG flag
to notify the hmwod framework of this hard requirement so that
__raw_writew/readw is used to read /write the mdoule registers.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Get rid of the following warning:
arch/arm/mach-omap1/devices.c: In function 'omap_init_wdt':
arch/arm/mach-omap1/devices.c:298: warning: 'return' with
no value, in function returning non-void
while at that, also change:
platform_device_register();
return 0;
into:
return platform_device_register();
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes the loader and bootenv partitions read-only under MTD for the
on-board NOR flash.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add kernel-doc documentation for the EP93xx DMA memory to
peripheral/peripheral to memory API.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old apcs-gnu ABI doesn't guarantee that double words are allocated
to registers with even alignment, causing the 64-bit exclusive memory
operations to be rejected by the assembler.
This patch requires that CONFIG_AEABI is set in order to use the native
atomic operations and falls back to the generic (spinlock) code otherwise.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
armv7_pmnc_counter_has_overflowed can return uninitialised data
if an invalid counter is specified.
This patch fixes the code to return 0 in this case, which squashes
the compiler warning from GCC 4.5.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When unwinding stack frames we must take care not to unwind
areas of memory that lie outside of the known extent of the stack.
This patch fixes an incorrect calculation of the stack base where
THREAD_SIZE is added to the stack pointer after it has already
been aligned to this value. Since the ALIGN macro performs this
addition internally, we end up overshooting the base by 8k.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
An out by one bug meant that the DMA coherent allocator was aligning
to one more bit than it should, causing it to run out of available
memory quicker. Fix this.
Reported-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Set onenand_setup to NULL instead of adding a no-op function.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
#include <media/omap1_camera.h> directive is required to
compile the dependant boards (board-ams-delta for now).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Flush the writes to IRQSTATUS_L0 register in the DMA interrupt handler by reading the register
directly after write. This prevents the spurious DMA interrupts noted when using VDD_OPP 1
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Acked-by: Santosh Shilimkar <Santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following error:
>regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
>twl_reg twl_reg.6: can't register VMMC1, -22
>twl_reg: probe of twl_reg.6 failed with error -22
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong MPP configuration would cause <cpu>_mpp_conf loop infinitely
because the mpp list iterator would not be incremented.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The type was IORESOURCE_IO which is not what is expected by
plat_nand_probe(). This device has not worked since 2d098a72
("mtd: plat_nand: request memory resource before doing ioremap").
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
As non-PFC chips are added that may support IRQs, pass through to the
generic helper. This follows the the SH change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The updated sh clock framework has introduced a .nr_freqs element of struct
clk, which has to be initialised with the number of possible frequencies.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This function should be marked as __init because it is used only
in the init phase.
This fix the compiler warning:
LD arch/arm/mach-mx3/built-in.o
WARNING: arch/arm/mach-mx3/built-in.o(.text+0x1328): Section mismatch in reference from the function eet_init_devices() to the (unknown reference) .init.rodata:(unknown)
The function eet_init_devices() references
the (unknown reference) __initconst (unknown).
This is often because eet_init_devices lacks a __initconst
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Many of the config bit are presently duplicated between the platforms,
which will gradually cleaned up through centralization. For the moment we
expose some new INTC features through drivers/sh/Kconfig that the ARM
platforms presently don't enable, so make it generally available.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: fix erroneous platform data in U300
spi: fixed odd static string conventions in core code
spi/bfin_spi: only request GPIO on first load
spi/bfin_spi: handle error/status changes after data interrupts
spi: enable spi_board_info to be registered after spi_master
This fixes an erroneous use of LSB first in the U300 machine, the
PL022 used in U300 is a standard ARM core that doesn't support this
bit so it should never have been set.
Cc: Kevin Wells <wellsk40@gmail.com>OA
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.infradead.org/mtd-2.6: (82 commits)
mtd: fix build error in m25p80.c
mtd: Remove redundant mutex from mtd_blkdevs.c
MTD: Fix wrong check register_blkdev return value
Revert "mtd: cleanup Kconfig dependencies"
mtd: cfi_cmdset_0002: make sector erase command variable
mtd: cfi_cmdset_0002: add CFI detection for SST 38VF640x chips
mtd: cfi_util: add support for switching SST 39VF640xB chips into QRY mode
mtd: cfi_cmdset_0001: use defined value of P_ID_INTEL_PERFORMANCE instead of hardcoded one
block2mtd: dubious assignment
P4080/mtd: Fix the freescale lbc issue with 36bit mode
P4080/eLBC: Make Freescale elbc interrupt common to elbc devices
mtd: phram: use KBUILD_MODNAME
mtd: OneNAND: S5PC110: Fix double call suspend & resume function
mtd: nand: fix MTD_MODE_RAW writes
jffs2: use kmemdup
mtd: sm_ftl: cosmetic, use bool when possible
mtd: r852: remove useless pci powerup/down from suspend/resume routines
mtd: blktrans: fix a race vs kthread_stop
mtd: blktrans: kill BKL
mtd: allow to unload the mtdtrans module if its block devices aren't open
...
Fix up trivial whitespace-introduced conflict in drivers/mtd/mtdchar.c
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (215 commits)
ARM: memblock: setup lowmem mappings using memblock
ARM: memblock: move meminfo into find_limits directly
ARM: memblock: convert free_highpages() to use memblock
ARM: move freeing of highmem pages out of mem_init()
ARM: memblock: convert memory detail printing to use memblock
ARM: memblock: use memblock to free memory into arm_bootmem_init()
ARM: memblock: use memblock when initializing memory allocators
ARM: ensure membank array is always sorted
ARM: 6466/1: implement flush_icache_all for the rest of the CPUs
ARM: 6464/2: fix spinlock recursion in adjust_pte()
ARM: fix memblock breakage
ARM: 6465/1: Fix data abort accessing proc_info from __lookup_processor_type
ARM: 6460/1: ixp2000: fix type of ixp2000_timer_interrupt
ARM: 6449/1: Fix for compiler warning of uninitialized variable.
ARM: 6445/1: fixup TCM memory types
ARM: imx: Add wake functionality to GPIO
ARM: mx5: Add gpio-keys to mx51 babbage board
ARM: imx: Add gpio-keys to plat-mxc
mx31_3ds: Fix spi registration
mx31_3ds: Fix the logic for detecting the debug board
...
Conflicts:
drivers/mtd/mtd_blkdevs.c
Merge Grant's device-tree bits so that we can apply the subsequent fixes.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-2637/s3c24xx-all' of git://git.fluff.org/bjdooks/linux:
ARM: h1940: add UDA1380 to i2c devices list
ARM: h1940: Fix backlight and LCD power functions
ARM: S3C2440: fix boot failure introduced by recent changes in gpiolib
ARM: S3C2440: various fixes in Kconfig file
ARM: rx1950: Add UDA1380 to i2c devices list
ARM: rx1950: Add LEDs support
ARM: rx1950: Add battery device
ARM: h1940: Implement mmc_power function
ARM: h1940: Use gpiolib for latch access
Current implementation of LCD and backlight power control functions
is not complete, as result PDA consumes power in suspend.
Fix this issue by managing state of some latch bits, just like
WinMobile does.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Recent changes in s3c gpio break mini2440 board and may be others.
The problem is that mach-mini2440.c: mini2440_init()
(where we call s3c_gpio_setpull()) is called before s3c2440.c: s3c2440_init()
(where we initialize s3c24xx_gpiocfg_default.set_pull function pointer).
This causes dereferencing of NULL pointer at boot time and a kernel panic.
Signed-off-by: Abdoulaye Walsimou Gaye <awg@embtoolkit.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* kconfig symbols defined in arch/arm/mach-s3c2440/Kconfig are only available
when ARCH_S3C2410 is selected, so no need to make some of them depend
on ARCH_S3C2410.
* fix CPU_S3C24405B typo in "config S3C2440_DMA".
* mini2440: remove unconditionally select of SND_S3C24XX_SOC_S3C24XX_UDA134X.
Those fixes avoid the following warnings at make time:
scripts/kconfig/qconf arch/arm/Kconfig
warning: (MACH_MINI2440 && ARCH_S3C2410) selects SND_S3C24XX_SOC_S3C24XX_UDA134X
which has unmet direct dependencies (SND_S3C24XX_SOC && ARCH_S3C2410)
warning: (CPU_S3C2440 && ARCH_S3C2410 && S3C2410_DMA) selects S3C2440_DMA which
has unmet direct dependencies (ARCH_S3C2410 && CPU_S3C24405B)
warning: (CPU_S3C2440 && ARCH_S3C2410 || CPU_S3C2442 && ARCH_S3C2410)
selects CPU_S3C244X which has unmet direct dependencies (!ARCH_S3C2410)
Signed-off-by: Abdoulaye Walsimou Gaye <awg@embtoolkit.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If the board has a debug uart the user is given a choice of which
uart to use. The user can also select NONE, which means not to use one.
In most of our header files when NONE is selected nothing is defined
for MSM_DEBUG_UART_PHYS or MSM_DEBUG_UART_BASE. This causes a compile
failure in debug-macro.S which expect something to be defined there.
Example of the failure,
arch/arm/kernel/built-in.o: In function `hexbuf':
linux-2.6/arch/arm/kernel/debug.S:186: undefined reference to `MSM_DEBUG_UART_PHYS'
linux-2.6/arch/arm/kernel/debug.S:186: undefined reference to `MSM_DEBUG_UART_BASE'
This fixes the compile failure by adding an ifdef to debug-macro.S
that removes all the debug uart code in the case of NONE.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Originally there was an ifdef case to handle when no debug uart
was selected. In commit 0ea1293009
that case was removed which causes the following build failure,
linux-2.6/arch/arm/kernel/debug.S: Assembler messages:
linux-2.6/arch/arm/kernel/debug.S:174: Error: bad instruction `addruart r1,r2'
linux-2.6/arch/arm/kernel/debug.S:176: Error: bad instruction `waituart r2,r3'
linux-2.6/arch/arm/kernel/debug.S:177: Error: bad instruction `senduart r1,r3'
linux-2.6/arch/arm/kernel/debug.S:178: Error: bad instruction `busyuart r2,r3'
linux-2.6/arch/arm/kernel/debug.S:190: Error: bad instruction `addruart r1,r2'
This is a partial revert to add back the case which was removed with
two caveats. First the API for the addruart macro was updated, and
the new addruart case now return 0xfff00000 so that a know IO mapping
is created instead of a random one.
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jason Wang <jason77.wang@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
DBG_MAX_REG_NUM incorrectly had the number of indices in the GDB regs
array rather than the number of registers, leading to an oops when the
"rd" command is used in KDB.
Cc: stable@kernel.org
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (38 commits)
kbuild: convert `arch/tile' to the kconfig mainmenu upgrade
README: cite nconfig
Revert "kconfig: Temporarily disable dependency warnings"
kconfig: Use PATH_MAX instead of 128 for path buffer sizes.
kconfig: Fix realloc usage()
kconfig: Propagate const
kconfig: Don't go out from read config loop when you read new symbol
kconfig: fix menuconfig on debian lenny
kbuild: migrate all arch to the kconfig mainmenu upgrade
kconfig: expand file names
kconfig: use the file's name of sourced file
kconfig: constify file name
kconfig: don't emit warning upon rootmenu's prompt redefinition
kconfig: replace KERNELVERSION usage by the mainmenu's prompt
kconfig: delay gconf window initialization
kconfig: expand by default the rootmenu's prompt
kconfig: add a symbol string expansion helper
kconfig: regen parser
kconfig: implement the `mainmenu' directive
kconfig: allow PACKAGE to be defined on the compiler's command-line
...
Fix up trivial conflict in arch/mn10300/Kconfig
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030. This functionality was introduced in mfd tree on
track to kernel.org
Sync pandaboard to the same and make mmc work.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In preparation for the addition of SPI support for the WM831x move the I2C
specific code into a separate file with a separate Kconfig option so the
I2C support can be excluded from the build.
Also update the 1133-EV1 PMIC module support for SMDK6410 to use the new
symbol.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On AP4EVB the card detect pin of the top SD/MMC slot is not directly
connected to the tmio/mmcif controller but to a GPIO pin, so polling
needs to be done for SDHI1 and MMCIF in order to support hotplug for
that slot. SHDI1 and MMCIF share that slot, and the used controller
is selected by a DIP switch.
This patch adds a helper function to check if a card is present in that
particular slot, registers this function with SDHI1 and MMCIF and enables
polling for SDHI1.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This merges the staging-next tree to Linus's tree and resolves
some conflicts that were present due to changes in other trees that were
affected by files here.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (505 commits)
[media] af9015: Fix max I2C message size when used with tda18271
[media] IR: initialize ir_raw_event in few more drivers
[media] Guard a divide in v4l1 compat layer
[media] imon: fix nomouse modprobe option
[media] imon: remove redundant change_protocol call
[media] imon: fix my egregious brown paper bag w/rdev/idev split
[media] cafe_ccic: Configure ov7670 correctly
[media] ov7670: allow configuration of image size, clock speed, and I/O method
[media] af9015: support for DigitalNow TinyTwin v3 [1f4d:9016]
[media] af9015: map DigitalNow TinyTwin v2 remote
[media] DigitalNow TinyTwin remote controller
[media] af9015: RC fixes and improvements
videodev2.h.xml: Update to reflect the latest changes at videodev2.h
[media] v4l: document new Bayer and monochrome pixel formats
[media] DocBook/v4l: Add missing formats used on gspca cpia1 and sn9c2028
[media] firedtv: add parameter to fake ca_system_ids in CA_INFO
[media] tm6000: fix a macro coding style issue
tm6000: Remove some ugly debug code
[media] Nova-S-Plus audio line input
[media] [RFC,1/1] V4L2: Use new CAP bits in existing RDS capable drivers
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: add new sdhci-pxa driver for Marvell SoCs
mmc: make number of mmcblk minors configurable
mmc_spi: Recover from CRC errors for r/w operation over SPI.
mmc: sdhci-pltfm: add -pltfm driver for imx35/51
mmc: sdhci-of-esdhc: factor out common stuff
mmc: sdhci_pltfm: pass more data on custom init call
mmc: sdhci: introduce get_ro private write-protect hook
mmc: sdhci-pltfm: move .h file into appropriate subdir
mmc: sdhci-pltfm: Add structure for host-specific data
mmc: fix cb710 kconfig dependency warning
mmc: cb710: remove debugging printk (info duplicated from mmc-core)
mmc: cb710: clear irq handler on init() error path
mmc: cb710: remove unnecessary msleep()
mmc: cb710: implement get_cd() callback
mmc: cb710: partially demystify clock selection
mmc: add a file to debugfs for changing host clock at runtime
mmc: sdhci: allow for eMMC 74 clock generation by controller
mmc: sdhci: highspeed: check for mmc as well as sd cards
mmc: sdhci: Add Moorestown device support
mmc: sdhci: Intel Medfield support
...
Use memblock information to setup lowmem mappings rather than the
membank array.
This allows platforms to manipulate the memblock information during
initialization to reserve (and remove) memory from the kernel's view
of memory - and thus allowing platforms to setup their own private
mappings for this memory without causing problems with multiple
aliasing mappings:
size = min(size, SZ_2M);
base = memblock_alloc(size, min(align, SZ_2M));
memblock_free(base, size);
memblock_remove(base, size);
This is needed because multiple mappings of regions with differing
attributes (sharability, type, cache) are not permitted with ARMv6
and above.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
bootmem_init() no longer makes several uses of the membank
information, so move this into the one remaining called function
which does use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Free the high pages using the memblock memory lists - and more
importantly, exclude any memblock allocations in highmem from the
free'd memory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This was missing from the noMMU code, so there was the possibility
of things not working as expected if out of order memory information
was passed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 81d11955bf ("ARM: 6405/1: Handle __flush_icache_all for
CONFIG_SMP_ON_UP") added a new function to struct cpu_cache_fns:
flush_icache_all(). It also implemented this for v6 and v7 but not
for v5 and backwards. Without the function pointer in place, we
will be calling wrong cache functions.
For example with ep93xx we get following:
Unable to handle kernel paging request at virtual address ee070f38
pgd = c0004000
[ee070f38] *pgd=00000000
Internal error: Oops: 80000005 [#1] PREEMPT
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.36+ #1)
PC is at 0xee070f38
LR is at __dma_alloc+0x11c/0x2d0
pc : [<ee070f38>] lr : [<c0032c8c>] psr: 60000013
sp : c581bde0 ip : 00000000 fp : c0472000
r10: c0472000 r9 : 000000d0 r8 : 00020000
r7 : 0001ffff r6 : 00000000 r5 : c0472400 r4 : c5980000
r3 : c03ab7e0 r2 : 00000000 r1 : c59a0000 r0 : c5980000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: c000717f Table: c0004000 DAC: 00000017
Process swapper (pid: 1, stack limit = 0xc581a270)
[<c0032c8c>] (__dma_alloc+0x11c/0x2d0)
[<c0032e5c>] (dma_alloc_writecombine+0x1c/0x24)
[<c0204148>] (ep93xx_pcm_preallocate_dma_buffer+0x44/0x60)
[<c02041c0>] (ep93xx_pcm_new+0x5c/0x88)
[<c01ff188>] (snd_soc_instantiate_cards+0x8a8/0xbc0)
[<c01ff59c>] (soc_probe+0xfc/0x134)
[<c01adafc>] (platform_drv_probe+0x18/0x1c)
[<c01acca4>] (driver_probe_device+0xb0/0x16c)
[<c01ac284>] (bus_for_each_drv+0x48/0x84)
[<c01ace90>] (device_attach+0x50/0x68)
[<c01ac0f8>] (bus_probe_device+0x24/0x44)
[<c01aad7c>] (device_add+0x2fc/0x44c)
[<c01adfa8>] (platform_device_add+0x104/0x15c)
[<c0015eb8>] (simone_init+0x60/0x94)
[<c0021410>] (do_one_initcall+0xd0/0x1a4)
__dma_alloc() calls (inlined) __dma_alloc_buffer() which ends up
calling dmac_flush_range(). Now since the entries in the
arm920_cache_fns are shifted by one, we jump into address 0xee070f38
which is actually next instruction after the arm920_cache_fns
structure.
So implement flush_icache_all() for the rest of the supported CPUs
using a generic 'invalidate I cache' instruction.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When running following code in a machine which has VIVT caches and
USE_SPLIT_PTLOCKS is not defined:
fd = open("/etc/passwd", O_RDONLY);
addr = mmap(NULL, 4096, PROT_READ, MAP_SHARED, fd, 0);
addr2 = mmap(NULL, 4096, PROT_READ, MAP_SHARED, fd, 0);
v = *((int *)addr);
we will hang in spinlock recursion in the page fault handler:
BUG: spinlock recursion on CPU#0, mmap_test/717
lock: c5e295d8, .magic: dead4ead, .owner: mmap_test/717,
.owner_cpu: 0
[<c0026604>] (unwind_backtrace+0x0/0xec)
[<c014ee48>] (do_raw_spin_lock+0x40/0x140)
[<c0027f68>] (update_mmu_cache+0x208/0x250)
[<c0079db4>] (__do_fault+0x320/0x3ec)
[<c007af7c>] (handle_mm_fault+0x2f0/0x6d8)
[<c0027834>] (do_page_fault+0xdc/0x1cc)
[<c00202d0>] (do_DataAbort+0x34/0x94)
This comes from the fact that when USE_SPLIT_PTLOCKS is not defined,
the only lock protecting the page tables is mm->page_table_lock
which is already locked before update_mmu_cache() is called.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (48 commits)
DMAENGINE: move COH901318 to arch_initcall
dma: imx-dma: fix signedness bug
dma/timberdale: simplify conditional
ste_dma40: remove channel_type
ste_dma40: remove enum for endianess
ste_dma40: remove TIM_FOR_LINK option
ste_dma40: move mode_opt to separate config
ste_dma40: move channel mode to a separate field
ste_dma40: move priority to separate field
ste_dma40: add variable to indicate valid dma_cfg
async_tx: make async_tx channel switching opt-in
move async raid6 test to lib/Kconfig.debug
dmaengine: Add Freescale i.MX1/21/27 DMA driver
intel_mid_dma: change the slave interface
intel_mid_dma: fix the WARN_ONs
intel_mid_dma: Add sg list support to DMA driver
intel_mid_dma: Allow DMAC2 to share interrupt
intel_mid_dma: Allow IRQ sharing
intel_mid_dma: Add runtime PM support
DMAENGINE: define a dummy filter function for ste_dma40
...
use new 'datap' variable in order to remove unnecessary castings.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the arguments to arch_ptrace() to take account of the fact that
@addr and @data are now unsigned long rather than long as of a preceding
patch in this series.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph reported a nice splat which illustrated a race in the new stack
based kmap_atomic implementation.
The problem is that we pop our stack slot before we're completely done
resetting its state -- in particular clearing the PTE (sometimes that's
CONFIG_DEBUG_HIGHMEM). If an interrupt happens before we actually clear
the PTE used for the last slot, that interrupt can reuse the slot in a
dirty state, which triggers a BUG in kmap_atomic().
Fix this by introducing kmap_atomic_idx() which reports the current slot
index without actually releasing it and use that to find the PTE and delay
the _pop() until after we're completely done.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Christoph Hellwig <hch@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The shift of 24 causes the shift and multiply operation to sometimes
overflow, resulting in incorrect timer values and poor performance.
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This prevents build failures since it's currently possible to select
8x50, 7x30, or 7x00 without selecting a specific board. These changes
just force a target selection, which is currently defaulting to the most
common one (7x30 only has one).
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
In commit be37030274
"ARM: Remove DISCONTIGMEM support", it removed this "node" member
which cased the following compile failure in mach-msm,
linux/arch/arm/mach-msm/board-halibut.c: In function 'halibut_fixup':
linux/arch/arm/mach-msm/board-halibut.c:86: error: 'struct membank' has no member named 'node'
linux/arch/arm/mach-msm/board-halibut.c:86: error: implicit declaration of function 'PHYS_TO_NID'
I've removed the access to the node member which corrects the
compile failure.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Will says:
| Commit e63075a3 removed the explicit MEMBLOCK_REAL_LIMIT #define
| and introduced the requirement that arch code calls
| memblock_set_current_limit to ensure that the __va macro can
| be used on physical addresses returned from memblock_alloc.
Unfortunately, ARM was missed out of this change. Fix this.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 5085f3ff45 added better support for
CONFIG_HOTPLUG_CPU by keeping proc_info around. However, depending on
the Kconfig options selected, this can make the booting fail mysteriously
early on.
Turns out a data abort can happen in __lookup_processor in ldmia r5 {r3, r4}.
When it happens the address loaded to r5 is not aligned. Fix the problem by
aligning proc_info.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a build warning existing since at least 2.6.30:
arch/arm/mach-ixp2000/core.c:217: warning: initialization from incompatible pointer type
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: mach-sa1100: Fix for compiler warning of uninitialized variable.
This is a fix for the compiler warning: 'new_ppcr' may be used
uninitialized in this function.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After Santosh's fixup of the generic MT_MEMORY and
MT_MEMORY_NONCACHED I add this fix to the TCM memory types.
The main change is that the ITCM memory is L_PTE_WRITE and
DOMAIN_KERNEL which works just fine. The changed to the DTCM
is just cosmetic to fit with surrounding code.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the new {max,min}3 macros to save some cycles and bytes on the stack.
This patch substitutes trivial nested macros with their counterpart.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Joe Perches <joe@perches.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we no longer need to provide KM_type, the whole pte_*map_nested()
API is now redundant, remove it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keep the current interface but ignore the KM_type and use a stack based
approach.
The advantage is that we get rid of crappy code like:
#define __KM_PTE \
(in_nmi() ? KM_NMI_PTE : \
in_irq() ? KM_IRQ_PTE : \
KM_PTE0)
and in general can stop worrying about what context we're in and what kmap
slots might be appropriate for that.
The downside is that FRV kmap_atomic() gets more expensive.
For now we use a CPP trick suggested by Andrew:
#define kmap_atomic(page, args...) __kmap_atomic(page)
to avoid having to touch all kmap_atomic() users in a single patch.
[ not compiled on:
- mn10300: the arch doesn't actually build with highmem to begin with ]
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix up drivers/gpu/drm/i915/intel_overlay.c]
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/battery-2.6:
power_supply: Makefile cleanup
bq27x00_battery: Add missing kfree(di->bus) in bq27x00_battery_remove()
power_supply: Introduce maximum current property
power_supply: Add types for USB chargers
ds2782_battery: Fix units
power_supply: Add driver for TWL4030/TPS65950 BCI charger
bq20z75: Add support for more power supply properties
wm831x_power: Add missing kfree(wm831x_power) in wm831x_power_remove()
jz4740-battery: Add missing kfree(jz_battery) in jz_battery_remove()
ds2760_battery: Add missing kfree(di) in ds2760_battery_remove()
olpc_battery: Fix endian neutral breakage for s16 values
ds2760_battery: Fix W1 and W1_SLAVE_DS2760 dependency
pcf50633-charger: Add missing sysfs_remove_group()
power_supply: Add driver for TI BQ20Z75 gas gauge IC
wm831x_power: Remove duplicate chg mask
omap: rx51: Add support for USB chargers
power_supply: Add isp1704 charger detection driver
* 'for_linus' of git://github.com/at91linux/linux-2.6-at91:
AT91: rtc: enable built-in RTC in Kconfig for at91sam9g45 family
at91/atmel-mci: inclusion of sd/mmc driver in at91sam9g45 chip and board
AT91: pm: make sure that r0 is 0 when dealing with cache operations
AT91: pm: use plain cpu_do_idle() for "wait for interrupt"
AT91: reset: extend alternate reset procedure to several chips
AT91: reset routine cleanup, remove not needed icache flush
AT91: trivial: align comment of at91sam9g20_reset with one more tab
AT91: Fix AT91SAM9G20 reset as per the errata in the data sheet
AT91: add board support for Pcontrol_G20
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux:
OMAP: DSS2: don't power off a panel twice
OMAP: DSS2: OMAPFB: Allow usage of def_vrfb only for omap2,3
OMAP: DSS2: OMAPFB: make VRFB depends on OMAP2,3
OMAP: DSS2: OMAPFB: Allow FB_OMAP2 to build without VRFB
arm/omap: simplify conditional
OMAP: DSS2: DSI: Remove extra iounmap in error path
OMAP: DSS2: Use dss_features framework on DSS2 code
OMAP: DSS2: Introduce dss_features files
video/omap: remove mux.h include
ARM: omap/fb: move get_fbmem_region() to .init.text
ARM: omap/fb: move omapfb_reserve_sram to .init.text
ARM: omap/fb: move omap_init_fb to .init.text
OMAP: DSS2: OMAPFB: swap front and back porches for both hsync and vsync
OMAP: DSS2: make filter coefficient tables human readable
OMAP: DSS2: Add SPI dependency to Kconfig of ACX565AKM panel
Add function definition for irq_chip.set_wake to enable GPIO to
wake-up the system.
This patch has been tested on a MX51 Babbage system that had suspend
code implemented. The set_wake implementation is necessary for a
GPIO to wake up a system from suspend.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add functionality for the power button on MX51 Babbage board.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The function mxc_expio_init returns 0 on success, so fix the logic for
printing the error case.
Also fixed the wording on the error message.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and
board files. This also configures the DMA controller slave interface for
at_hdmac dmaengine driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
When using CP15 cache operations (c7), we make sure that Rd (r0)
is actually 0 as ARM 926 TRM is saying.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For power management at91_pm_enter() routine, use the cpu_do_idle() for a
rock solid "wait for interrupt" implementation.
For AT91SAM9 ARM 926 based chips, we can exceed the cache line length as
we can access RAM even while in self-refresh mode.
We keep plain access to CP15 for at91rm9200 as this feature is not
available: instructions have to be in a single cache line.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Several at91sam9 chips need the alternate reset procedure to be sure to halt
SDRAM smoothly before resetting the chip.
This is an extension of previous patch "Fix AT91SAM9G20 reset" to all chips
affected.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Generalize assembler reset routine to allow use on several at91sam9 chips.
This patch replace double definitions of SDRAM controller registers and RSTC
registers with use of classical header files.
For this rework, we remove the not needed icache flush as it is already
done in the calling function: arm_machine_restart().
Rename at91sam9g20_reset.S to generalize to several chips.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
If the SDRAM is not cleanly shutdown before reset it can be left driving
the bus, which then stops the bootloader booting from NAND.
Signed-off-by: Peter Horton <phorton@bitbox.co.uk>
[nicolas.ferre@atmel.com: change file header line order]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Board is a carrier board for Stamp9G20, with additional peripherals
for a building automation system
Signed-off-by: Peter Gsellmann <pgsellmann@portner-elektronik.at>
[nicolas.ferre@atmel.com: remove machine_desc.io_pg_offst and .phys_io]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The generic version of l2x0_inv_all is only called just after disabling
the L2 cache and is surrounded by a spinlock. However, we're not really
turning off the L2 cache right now, and the PL310 does not support
exclusive accesses (used to implement the spinlock). So, the
invalidation needs to be done without the spinlock.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Hans-Juergen Koch <hjk@linutronix.de>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
For the big buffers which are in excess of cache size, the maintaince
operations by PA are very slow. For such buffers the maintainace
operations can be speeded up by using the WAY based method.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
The cache size is needed for to optimise range based
maintainance operations
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Replace tab with space after #define to be consisten with other
define in the file. Also move the bit mask below the register offsets.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
The machine_kexec() calls outer_disable which can crash on OMAP4
becasue of trustzone restrictions.
This patch overrides the default l2x0_disable with a OMAP4
specific implementation taking care of trustzone
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Add flush_all, inv_all and disable functions to the l2x0 code. These
functions are called from kexec code to prevent random crashes in the
new kernel.
Platforms like OMAP which control L2 enable/disable via SMI mode can
override the outer_cache.disable() function to implement their own.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
kexec does not disable the outer cache before disabling the inner
caches in cpu_proc_fin(). So L2 is enabled across the kexec jump. When
the new kernel enables chaches again, it randomly crashes.
Disabling L2 before calling cpu_proc_fin() cures the problem.
Disabling L2 requires the following new functions: flush_all(),
inv_all() and disable(). Add them to outer_cache_fns and call them
from the kexec code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
With this L2 cache controller, the cache maintenance by PA and sync
operations are atomic and do not require a "wait" loop. This patch
conditionally defines the cache_wait() function.
Since L2x0 cache controllers do not work with ARMv7 CPUs, the patch
automatically enables CACHE_PL310 when only CPU_V7 is defined.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds to support ethernet for SMDKV310 and SMDKC210 board.
- define smc911x resources
- define configurations of smc911x platform data
- define platform device "smsc911x"
- initialize srom controller for lan9215 chip
Signed-off-by: Daein Moon <moon9124@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In commit (c5d38f08): "mx31_3ds: revert 3ds debug board relate code"
the debug board definitions are placed in a separate file.
Remove the remaining debug board related define from mach-mx31_3ds.c.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support SROMC for S5PV310 and S5PC210.
Signed-off-by: Daein Moon <moon9124@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the s3c_gpio_getpull() API that has been missed in the
plat-samsung/gpio-config.c and actullay there is its extern declaration
in plat/gpio-cfg.h.
Signed-off-by: Daein Moon <moon9124@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
hwmon: lis3: Release resources in case of failure
hwmon: lis3: Short explanations of platform data fields
hwmon: lis3: Enhance lis3 selftest with IRQ line test
hwmon: lis3: use block read to access data registers
hwmon: lis3: Adjust fuzziness for 8 bit device
hwmon: lis3: New parameters to platform data
hwmon: lis3: restore axis enabled bits
hwmon: lis3: Power on corrections
hwmon: lis3: Update coordinates at polled device open
hwmon: lis3: Cleanup interrupt handling
hwmon: lis3: regulator control
hwmon: lis3: pm_runtime support
Kirkwood: add fan support for Network Space Max v2
hwmon: add generic GPIO fan driver
hwmon: (coretemp) fix reading of microcode revision (v2)
hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefs
hwmon: (pkgtemp) align driver initialization style with coretemp
hwmon: LTC4261 Hardware monitoring driver
hwmon: (lis3) add axes module parameter for custom axis-mapping
hwmon: (hp_accel) Add HP Mini 510x family support
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
This patch changes VMALLOC_END from 0xE0000000 to 0xF6000000, because
some systems want to use more vmalloc()/ioremap() area and now don't use
from at 0xE0000000 to 0xF6000000 (the start of Samsung SoCs' VA space)
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes VMALLOC_END from 0xE0000000 to 0xF6000000, because
some systems want to use more vmalloc()/ioremap() area and now don't use
from at 0xE0000000 to 0xF6000000 (the start of Samsung SoCs' VA space)
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves the start address of Samsung SoCs' VA space so that
can use more vmalloc()/ioremap() space. Of course need to change the
VMALLOC_END for it.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds EINT(External Interrupt) support on S5PV310 and S5PC210.
All EINTs are transferred to GIC through interrupt combiner.
Signed-off-by: Jongsun Han <jongsun.han@samsung.com>
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the definition for both IRQs and GPIO registers for
external interrupts.
Signed-off-by: Jongsun Han <jongsun.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds L2 cache initialization code in cpu.c of ARCH_S5PV310.
It includes TAG and Data latency, Prefetch, and Power configurations.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Basically, need L2 cache initialize function in ARCH_S5PV310. So it would
be better to move it into ARCH_S5PV310 common part. This patch removes L2
cache initialization code at the each board file.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds L2X0 Prefetch and Power control register.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves DMA clock enable functionality into pl330_probe() of
plat-samsung/s3c_pl330.c (PL330 DMAC driver) and disable functionality
into pl330_remove().
For now according to clock policy of Samsung SoCs' mainline, clocks which
are used in the driver should be controlled by each own.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
[kgene.kim@samsung.com: minor title and comment edit]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is matched-up DMA platform device id to its clock id.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch modify to DMA operation clock into disable list for default
clock setting.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds DMA operation clock which is disabled as default.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds DMA operation clock which is disabled as default.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Audio, Keypad and ADC inherit PCLKD1 clock source.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add cose related to regulator. To control powre consumeption
have registered the voltage consumer of WM8994 to the regulator framework.
Additionally, I explain the constraints of the regulator of WM8994 codec.
All these consumer supply of WM8994 codec connected the regulator(VCC_1.8V)
on a circuit diagram. "VCC_1.8V" regulator is always enabled, because it is
used to many devices on Goni/Aquila board. This is required especially
when there are many devices physically attached to "VCC_1.8V" and some of
they did not "register" as consumers to "VCC_1.8V". "VCC_1.8V" might be
turned off by those who are registered while "unregistered" are still active
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
