Introduce CTA_LABELS attribute to send a bit-vector of currently active labels
to userspace.
Future patch will permit userspace to also set/delete active labels.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
similar to connmarks, except labels are bit-based; i.e.
all labels may be attached to a flow at the same time.
Up to 128 labels are supported. Supporting more labels
is possible, but requires increasing the ct offset delta
from u8 to u16 type due to increased extension sizes.
Mapping of bit-identifier to label name is done in userspace.
The extension is enabled at run-time once "-m connlabel" netfilter
rules are added.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Most SIP devices use a source port of 5060/udp on SIP requests, so the
response automatically comes back to port 5060:
phone_ip:5060 -> proxy_ip:5060 REGISTER
proxy_ip:5060 -> phone_ip:5060 100 Trying
The newer Cisco IP phones, however, use a randomly chosen high source
port for the SIP request but expect the response on port 5060:
phone_ip:49173 -> proxy_ip:5060 REGISTER
proxy_ip:5060 -> phone_ip:5060 100 Trying
Standard Linux NAT, with or without nf_nat_sip, will send the reply back
to port 49173, not 5060:
phone_ip:49173 -> proxy_ip:5060 REGISTER
proxy_ip:5060 -> phone_ip:49173 100 Trying
But the phone is not listening on 49173, so it will never see the reply.
This patch modifies nf_*_sip to work around this quirk by extracting
the SIP response port from the Via: header, iff the source IP in the
packet header matches the source IP in the SIP request.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since submit 621b4d6 the bnx2x driver support FW GRO.
However, when using the device with GRO enabled in bridging
scenarios throughput is very low, as the bridge expects all
incoming packets to be passed with CHECKSUM_PARTIAL -
a demand which is satisfied by the SW GRO implementation,
but was missed in the bnx2x driver implementation (which returned
CHECKSUM_UNNECESSARY).
Now, given that the traffic is supported by FW GRO (TCP/IP),
the bnx2x driver calculates the pseudo checksum by itself,
passing skbs with CHECKSUM_PARTIAL and giving a much better
throughput when receiving GRO traffic.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling interrupts, acknowledge the interrupt only
after configuring the IGU to the correct interrupt mode
(otherwise it would dirty selftests)
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get better control over interrupts during panic, and allow FW to
test outgoing Tx packets when stop-on-error is allowed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This revises and enhances the bnx2x register dump facilities,
adding support for `ethtool -w' on top of `ethtool -d'.
Signed-off-by: Miriam Shitrit <miris@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device is configured to act as either iscsi or fcoe
device in its nvram, prevent the other from being misused by
preventing its activation in the driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On rare occasions, self test link may fail since the link is
being sampled while it's still being stabilized.
To correct this behaviour, try to sample the link for 2 seconds
prior to declaring a failure.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current logic causes chips running in switch dependent multi-function
FCoE mode not to configure their MAC, leading to an all 0s MAC.
This patch configures the interface with the SAN Mac instead.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Self-tests following boot from SAN have failed as the
UNDI driver might leave some NIG interrupt indications.
This patch does the clean-up, clearing those indications
and allowing the test to pass.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy
auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting
in intermittent crc errors on jumbo frames with some link partners. Change
the code to do a read/modify/write.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netconsole is enabled, logging messages generated during tg3_open
can result in a null pointer dereference for the uninitialized tg3
status block. Use the irq_sync flag to disable polling in the early
stages. irq_sync is cleared when the driver is enabling interrupts after
all initialization is completed.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a5e371f61a ("drivers/net: delete
all code/drivers depending on CONFIG_MCA") most of the MCA drivers went,
including the Kconfig/Makefile hooks for ibmlana, but it seems that I
missed the "git rm" on these actual driver files, and with the namespace
overlap with machine check architecture, it got missed by various git
grep type checking done at that time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains netfilter fixes for 3.8-rc3,
they are:
* fix possible BUG_ON if several netns are in use and the nf_conntrack
module is removed, initial patch from Gao feng, final patch from myself.
* fix unset return value if conntrack zone are disabled at
compile-time, reported by Borislav Petkov, fix from myself.
* fix display error message via dmesg for arp_tables, from Jan Engelhardt.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects some problems with LSM/SELinux that were introduced
with the multiqueue patchset. The problem stems from the fact that the
multiqueue work changed the relationship between the tun device and its
associated socket; before the socket persisted for the life of the
device, however after the multiqueue changes the socket only persisted
for the life of the userspace connection (fd open). For non-persistent
devices this is not an issue, but for persistent devices this can cause
the tun device to lose its SELinux label.
We correct this problem by adding an opaque LSM security blob to the
tun device struct which allows us to have the LSM security state, e.g.
SELinux labeling information, persist for the lifetime of the tun
device. In the process we tweak the LSM hooks to work with this new
approach to TUN device/socket labeling and introduce a new LSM hook,
security_tun_dev_attach_queue(), to approve requests to attach to a
TUN queue via TUNSETQUEUE.
The SELinux code has been adjusted to match the new LSM hooks, the
other LSMs do not make use of the LSM TUN controls. This patch makes
use of the recently added "tun_socket:attach_queue" permission to
restrict access to the TUNSETQUEUE operation. On older SELinux
policies which do not define the "tun_socket:attach_queue" permission
the access control decision for TUNSETQUEUE will be handled according
to the SELinux policy's unknown permission setting.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Acked-by: Eric Paris <eparis@parisplace.org>
Tested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new permission to align with the new TUN multiqueue support,
"tun_socket:attach_queue".
The corresponding SELinux reference policy patch is show below:
diff --git a/policy/flask/access_vectors b/policy/flask/access_vectors
index 28802c5..a0664a1 100644
--- a/policy/flask/access_vectors
+++ b/policy/flask/access_vectors
@@ -827,6 +827,9 @@ class kernel_service
class tun_socket
inherits socket
+{
+ attach_queue
+}
class x_pointer
inherits x_device
Signed-off-by: Paul Moore <pmoore@redhat.com>
Acked-by: Eric Paris <eparis@parisplace.org>
Tested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_is_locked() on a non !SMP build is kind of useless.
BUG_ON(!spin_is_locked(xx)) is guaranteed to crash.
Just remove this check in reqsk_fastopen_remove() as
the callers do hold the socket lock.
Reported-by: Ketan Kulkarni <ketkulka@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Dave Taht <dave.taht@gmail.com>
Acked-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2 fixes to prevent unconditional re-compile of dts files on arm and arm64.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ9HKkAAoJEMhvYp4jgsXihT0H/RSUuhC02eQV7mkIJwPVROwd
8nbdRAes22g2nbBN0NDDsZ6GCGjVBx/rt1MhS/yhzE6GqKkT+MnpQ+yE3A0xK+BP
bdqYFmajXauHNrPo6jp9HRwui7BKU9GMl2bkN39kALtY35Fo25XaGelsC+ue6KAg
VFA+iuHG9wEaVbYX/77IyTDjSECKbrcfGGlN1WHIIrFjIQDMA7BjoNb9kyT5oS+l
kdS5n5MC1rCeg7lKD1ScVqPye5eOFjk35ZjJEfkfR/dXRsds1/wp17lH4rxC6Fcp
/9eEK3GeYAueQCTyHRDmkUtMGCA9qij0cUjVQkYf7Je6pHdQ5x7/eQXiHcKEv/M=
=cMYU
-----END PGP SIGNATURE-----
Merge tag 'dt-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux
Pull devicetree fixes from Rob Herring:
"Two fixes to prevent unconditional re-compile of dts files on arm and
arm64."
* tag 'dt-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux:
ARM: dts: prevent *.dtb from always being rebuilt
arm64: dts: prevent *.dtb from always being rebuilt
Andrew Morton pointed this out a month ago, and then I completely forgot
about it.
If we read a partial last page of a block device, we will zero out the
end of the page, but since that page can then be mapped into user space,
we should also make sure to flush the cache on architectures that have
virtual caches. We have the flush_dcache_page() function for this, so
use it.
Now, in practice this really never matters, because nobody sane uses
virtual caches to begin with, and they largely exist on old broken RISC
arhitectures.
And even if you did run on one of those obsolete CPU's, the whole "mmap
and access the last partial page of a block device" behavior probably
doesn't actually exist. The normal IO functions (read/write) will never
see the zeroed-out part of the page that migth not be coherent in the
cache, because they honor the size of the device.
So I'm marking this for stable (3.7 only), but I'm not sure anybody will
ever care.
Pointed-out-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org # 3.7
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ifb should lookup devices in the appropriate namespace.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet pointed out that act_mirred needs to find the current net_ns,
and struct net pointer is not provided in the call chain. His original
patch made use of current->nsproxy->net_ns to find the network namespace,
but this fails to work correctly for userspace code that makes use of
netlink sockets in different network namespaces. Instead, pass the
"struct net *" down along the call chain to where it is needed.
This version removes the ifb changes as Eric has submitted that patch
separately, but is otherwise identical to the previous version.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user is cxgb3 driver.
old_neigh is used to check device change, but it must not happen
on redirect. In this sense, we can remove old_neigh argument.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of commits found here are for ASoC device specific fixes,
arizona, cs4271, wm5102, wm2200, etc, in addition to a couple of
memory leak fixes in ASoC core.
Other than that, regression fixes in HD-audio and USB-audio, and
a fix for new Realtek codecs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=iVG2
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of commits found here are for ASoC device specific fixes,
arizona, cs4271, wm5102, wm2200, etc, in addition to a couple of
memory leak fixes in ASoC core.
Other than that, regression fixes in HD-audio and USB-audio, and a fix
for new Realtek codecs."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: usb-audio: Fix NULL dereference by access to non-existing substream
ALSA: hda - Add support of new codec ALC284
ALSA: usb-audio: Make ebox44_table static
ALSA: hdspm - Fix wordclock status on AES32
Revert "ALSA: hda - Shut up pins at power-saving mode with Conexnat codecs"
ALSA: hda - Disable runtime D3 for Intel CPT & co
ALSA: pxa27x: fix ac97 warm reset
ALSA: pxa27x: fix ac97 cold reset
ASoC: wm_adsp: Ensure that block writes are from DMA aligned addresses
ASoC: wm2000: Fix sense of speech clarity enable
ASoC: wm5100: Remove DSP B and left justified formats
ASoC: arizona: Remove DSP B and left justified AIF modes
ASoC: wm2200: Remove DSP B and left justified AIF modes
ASoC: wm5102: Improve speaker enable performance
ASoC: core: fix the memory leak in case of remove_aux_dev()
ASoC: core: fix the memory leak in case of device_add() failure
ASoC: cs42l52: Catch no-match case in cs42l52_get_clk
ASoC: lm49453: Update lm49453_reg_defs values as per LM49453 HW revision-B
ASoC: lm49453: Fix adc, mic and sidetone volume ranges
ASoC: arizona: Correct FLL source definitions
...
The removal of the 8390 EISA drivers actually comprises the
complete content of the EISA probe block, so we can now remove
that block, and its hook into the unified probe. Note that
the deleted comment mentions PCI probes, but they long since
moved elsewhere, so no PCI probes are touched here.
We get rid of the orphaned EISA probe prototypes, and a couple
of left over MCA probe prototypes at the same time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_prefix_equal() just casts its arguments and it is the only
user of __ipv6_prefix_equal().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce __ipv6_addr_diff64() to to find the first different
bit between two addresses on 64bit architectures.
32bit version is still available as __ipv6_addr_diff32(),
and __ipv6_addr_diff() automatically selects appropriate
version.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are a number of small fixes to staging drivers for your 3.8-rc3
tree.
Well, the omapdrm fixes aren't really "small" but they were waiting on a
number of other drm patches to go in through the drm tree, and got
delayed by my vacation over the holidays. They are totally
self-contained, everyone involved have acked them, and they fix issues
that people have been having with the driver.
Other than that one, it's a bunch of tiny bugfixes for a number of
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDzjqQACgkQMUfUDdst+ym/FgCfTOKtRk2YP9FJ+GlJnO7Ij2Ez
r/AAoJhhlxUwn59zhyCA6iIOLLix0tfU
=llcV
-----END PGP SIGNATURE-----
Merge tag 'staging-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg Kroah-Hartman:
"Here are a number of small fixes to staging drivers for your 3.8-rc3
tree.
Well, the omapdrm fixes aren't really "small" but they were waiting on
a number of other drm patches to go in through the drm tree, and got
delayed by my vacation over the holidays. They are totally
self-contained, everyone involved have acked them, and they fix issues
that people have been having with the driver.
Other than that one, it's a bunch of tiny bugfixes for a number of
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (36 commits)
staging: zram: fix invalid memory references during disk write
staging: tidspbridge: use prepare/unprepare on dsp clocks
staging: tidspbridge: Fix build breakage due to splitting CM functions.
staging: comedi: comedi_test: fix race when cancelling command
staging: comedi: Kconfig: COMEDI_NI_AT_A2150 should select COMEDI_FC
staging: comedi: prevent auto-unconfig of manually configured devices
staging: comedi: fix minimum AO period for NI 625x and NI 628x
staging: vme_pio2: fix oops on module unloading
staging: speakup: avoid out-of-range access in synth_add()
staging: speakup: avoid out-of-range access in synth_init()
staging: rtl8192e: Fix failure to check pci_map_single()
staging: rtl8187se: Fix failure to check pci_map_single()
staging: drm/imx: fix double free bug in error path
staging: drm/imx: several bug fixes
staging: drm/imx: check return value of ipu_reset()
staging: drm/omap: fix flags in dma buf exporting
staging: drm/omap: use omapdss low level API
staging/fwserial: Update TODO file per reviewer comments
staging/fwserial: Limit tx/rx to 1394-2008 spec maximum
staging/fwserial: Refine Kconfig help text
...
Here are a bunch of USB fixes for your 3.8-rc3 tree. They all either fix
problems that have been reported (like the xhci/hub changes) or add new device
ids to existing drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDzjz0ACgkQMUfUDdst+yn5YwCeOyqqCgQvyuP2JsacN/2a4wRN
Wn4AoM/Pg+b+B8M7Z/SBO10DRzj24xYj
=Kkq8
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a bunch of USB fixes for your 3.8-rc3 tree. They all either
fix problems that have been reported (like the xhci/hub changes) or
add new device ids to existing drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
usb: ftdi_sio: Crucible Technologies COMET Caller ID - pid added
usb: host: ohci-tmio: fix compile warning
USB: Add device quirk for Microsoft VX700 webcam
USB: ehci-fsl: fix regression on mpc5121e
usb: chipidea: Allow disabling streaming not only in udc mode
USB: fsl-mph-dr-of: fix regression on mpc5121e
USB: select USB_ARCH_HAS_EHCI for MXS
USB: hub: handle claim of enabled remote wakeup after reset
USB: cdc-acm: Add support for "PSC Scanning, Magellan 800i"
USB: option: add Nexpring NP10T terminal id
USB: option: add Telekom Speedstick LTE II
USB: option: blacklist network interface on ZTE MF880
usb: imx21-hcd: Include missing linux/module.h
USB: option: Add new MEDIATEK PID support
USB: ehci: make debug port in-use detection functional again
USB: usbtest: fix test number in log message
xhci: Avoid "dead ports", add roothub port polling.
USB: Handle warm reset failure on empty port.
USB: Ignore port state until reset completes.
USB: Increase reset timeout.
...
Here are two patches for 3.8-rc3.
One removes the __dev* defines from init.h now that all usages of it are gone
from your tree. The other fix is for debugfs's paramater that was using the
wrong base for the option.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDzjcAACgkQMUfUDdst+ykJVwCcDqiKrO9p0dcH9WXN5aukBWX/
N8EAoK786v7PjtiVyNOJ/cPUDU8OHUpg
=U4nL
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are two patches for 3.8-rc3.
One removes the __dev* defines from init.h now that all usages of it
are gone from your tree. The other fix is for debugfs's paramater
that was using the wrong base for the option.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: convert gid= argument from decimal, not octal
Remove __dev* markings from init.h
Here is a single fix for the mei driver that resolves a reported issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDzjO8ACgkQMUfUDdst+ymujgCfRtmhShKo0KJXYlIt13WrXKMg
h48An0jvjvpwBs0rL97cUN05H9Qk0/Nr
=8JYJ
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fix from Greg Kroah-Hartman:
"Here is a single fix for the mei driver that resolves a reported
issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: fix mismatch in mutex unlock-lock in mei_amthif_read()
Pull drm fixes from Dave Airlie:
"Nothing too astounding
- nouveau: bunch of regression fixes and oops fixes
- radeon: UMS fixes, rn50 fix, dma fix
- udl: fix EDID retrieval for large EDIDs."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
udldrmfb: udl_get_edid: drop unneeded i--
udldrmfb: udl_get_edid: usb_control_msg buffer must not be on the stack
udldrmfb: Fix EDID not working with monitors with EDID extension blocks
drm/nvc0/fb: fix crash when different mutex is used to protect same list
drm/nouveau/clock: fix support for more than 2 monitors on nve0
drm/nv50/disp: fix selection of bios script for analog outputs
drm/nv17-50: restore fence buffer on resume
drm/nouveau: fix blank LVDS screen regression on pre-nv50 cards
drm/nouveau: fix nouveau_client allocation failure path
drm/nouveau: don't return freed object from nouveau_handle_create
drm/nouveau/vm: fix memory corruption when pgt allocation fails
drm/nouveau: add locking around instobj list operations
drm/nouveau: do not forcibly power on lvds panels
drm/nouveau/devinit: ensure legacy vga control is enabled during post
radeon/kms: fix dma relocation checking
radeon/kms: force rn50 chip to always report connected on analog output
drm/radeon: fix error path in kpage allocation
drm/radeon: fix a bogus kfree
drm/radeon: fix NULL pointer dereference in UMS mode
Pull networking fixes from David Miller:
1) Fix regression allowing IP_TTL setting of zero, fix from Cong Wang.
2) Fix leak regressions in tunap, from Jason Wang.
3) be2net driver always returns IRQ_HANDLED in INTx handler, fix from
Sathya Perla.
4) qlge doesn't really support NETIF_F_TSO6, don't set that flag. Fix
from Amerigo Wang.
5) Add 802.11ad Atheros wil6210 driver, from Vladimir Kondratiev.
6) Fix MTU calculations in mac80211 layer, from T Krishna Chaitanya.
7) Station info layer of mac80211 needs to use del_timer_sync(), from
Johannes Berg.
8) tcp_read_sock() can loop forever, because we don't immediately stop
when recv_actor() returns zero. Fix from Eric Dumazet.
9) Fix WARN_ON() in tcp_cleanup_rbuf(). We have to use sk_eat_skb() in
tcp_recv_skb() to handle the case where a large GRO packet is split
up while it is use by a splice() operation. Fix also from Eric
Dumazet.
10) addrconf_get_prefix_route() in ipv6 tests flags incorrectly, it
does:
if (X && (p->flags & Y) != 0)
when it really meant to go:
if (X && (p->flags & X) != 0)
fix from Romain Kuntz.
11) Fix lost Kconfig dependency for bfin_mac driver hardware
timestamping. From Lars-Peter Clausen.
12) Fix regression in handling of RST without ACK in TCP, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
be2net: fix unconditionally returning IRQ_HANDLED in INTx
tuntap: fix leaking reference count
tuntap: forbid calling TUNSETIFF when detached
tuntap: switch to use rtnl_dereference()
net, wireless: overwrite default_ethtool_ops
qlge: remove NETIF_F_TSO6 flag
tcp: accept RST without ACK flag
net: ethernet: xilinx: Do not use NO_IRQ in axienet
net: ethernet: xilinx: Do not use axienet on PPC
bnx2x: Allow management traffic after boot from SAN
bnx2x: Fix fastpath structures when memory allocation fails
bfin_mac: Restore hardware time-stamping dependency on BF518
tun: avoid owner checks on IFF_ATTACH_QUEUE
bnx2x: move debugging code before the return
tuntap: refuse to re-attach to different tun_struct
ipv6: use addrconf_get_prefix_route for prefix route lookup [v2]
ipv6: fix the noflags test in addrconf_get_prefix_route
tcp: fix splice() and tcp collapsing interaction
tcp: splice: fix an infinite loop in tcp_read_sock()
net: prevent setting ttl=0 via IP_TTL
...
Pull sparc updates from David Miller:
1) Add finit_module syscall entry.
2) Remove stray __dev{init,exit} references, from Sam Ravnborg.
Fix up conflicts in the sparc PCI code due to whitespace differences in
the __dev{init,exit} removal (which also came in through Greg).
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: remove __devinit, __devexit annotations
sparc: Hook up finit_module syscall.
if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't
contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to
$(targets) to prevent *.dtb from always being rebuilt.
This fixes a regression introduced by the .dtb rule rework in 499cd82
"ARM: dt: change .dtb build rules to build in dts directory".
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't
contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to
$(targets) to prevent *.dtb from always being rebuilt. Note
This fixes a regression introduced by the .dtb rule rework in da4cbc6
"arm64: use new common dtc rule", although since arm64 doesn't actually
have any *.dts yet, this isn't a critical issue.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Fixes a bug introduced by commit c8f2f0db1 ("zram: Fix handling
of incompressible pages") which caused invalid memory references
during disk write. Invalid references could occur in two cases:
- Incoming data expands on compression: In this case, reference was
made to kunmap()'ed bio page.
- Partial (non PAGE_SIZE) write with incompressible data: In this
case, reference was made to a kfree()'ed buffer.
Fixes bug 50081:
https://bugzilla.kernel.org/show_bug.cgi?id=50081
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Cc: stable <stable@vger.kernel.org>
Reported-by: Mihail Kasadjikov <hamer.mk@gmail.com>
Reported-by: Tomas M <tomas@slax.org>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IN6ADDR_* and in6addr_* are not exported to userspace, and are defined
in include/linux/in6.h.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use per_cpu_add when possible
- prevent the TT component to add multicast address as "mesh clients"
- some debug output improvements
- proper lockdeps class initializations
- new style fixes (space before/after brackets)
- other minor fixes and refactoring
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=G3Vh
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- use per_cpu_add when possible
- prevent the TT component to add multicast address as "mesh clients"
- some debug output improvements
- proper lockdeps class initializations
- new style fixes (space before/after brackets)
- other minor fixes and refactoring
Signed-off-by: David S. Miller <davem@davemloft.net>
Router Alert option is very small and we can store the value
itself in the skb.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
