The ATA over Ethernet protocol uses a major (shelf) and minor (slot)
address to identify a particular storage target. These changes remove an
artificial limitation the aoe driver imposes on the use of AoE addresses.
For example, without these changes, the slot address has a maximum of 15,
but users commonly use slot numbers much greater than that.
The AoE shelf and slot address space is often used sparsely. Instead of
using a static mapping between AoE addresses and the block device minor
number, the block device minor numbers are now allocated on demand.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old area has a new URL. Also, now that the driver can perform better,
it is worth mentioning the VM settings that help aoe to sink dirty pages
out early, avoiding unecessary memory pressure when much I/O is going on.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The internal version number of the aoe driver appears in a console message
when the driver loads and is usually obtained by the user with the
userland aoe-version tool, part of the aoetools.[1]
Although this patchset includes bugfixes backported from higher-numbered
versions published on the coraid.com website, it is a form of version 49.
1. http://aoetools.sourceforge.net/
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change removes some unused code and attempts to increase code
consistency.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change eliminates the danger that the user could rmmod the driver for
a network interface that is being used for AoE by the aoe driver.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the driver code, "target" and aoetgt refer to a particular remote
interface on the AoE storage target. The latter is identified by its AoE
major and minor addresses. Commands that are being sent to an AoE storage
target {major, minor} can be sent or retransmitted to any of the remote
MAC addresses associated with the AoE storage target.
That is, frames are naturally associated with not an aoetgt (AoE major,
AoE minor, remote MAC address) but an aoedev (AoE major, AoE minor).
Making the code reflect that reality simplifies the driver, especially
when the path to a remote MAC address becomes unusable.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A guard is inserted to prevent AoE minor addresses (slot addresses) higher
than 15 to be used, as they are not yet supported by the driver.
There is a change coming that will allow the aoe driver to overcome this
limit by using system device minor numbers dynamically, but until then,
this guard prevents unexpected targets from being used by the driver when
AoE targets with high minor numbers are on the AoE network.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The discovery process begins with an optional AoE config query command and
an AoE config query response. Normally when an aoe device is already
open, the config query response does not trigger an ATA identify device
command to be sent out, since the response contains storage capacity
information that, if changed, could surprise the user of the device.
The userland "aoe-revalidate" tool uses a character device to trigger an
AoE config query for a particular AoE storage target and an ATA device
identify command, even when the device is open.
This change causes the config query to go out first, reflecting the normal
discovery sequence. The responses could come back in any order, so this
change is fairly cosmetic.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The aoe_deadsecs module parameter allows the user to specify a hard limit
on the number of seconds an AoE command can be retransmitted before the
AoE block device is considered to have failed.
Using aoe_deadsecs to determine the time we try using a different remote
interface helps to ensure that the hard limit is not reached before we've
tried to recover by sending to a different remote port.
As a data storage target, the AoE target is unambiguously identified by
its {major, minor} AoE address tuple, and an AoE target can have multiple
MAC addresses. However, note that "target" in the driver code and
comments means a {major, minor, MAC address} tuple, as in "somewhere to
send packets".
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Users with several network interfaces dedicated to AoE generally do not
configure them to support different-sized AoE data payloads on purpose.
For a given AoE target, there will be a set of local network interfaces
that can reach it. Using only the payload that will fit in the
smallest-sized MTU of all those local interfaces greatly simplifies the
driver, especially in failure scenarios.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dev_queue_xmit function needs to have interrupts enabled, so the most
simple way to get the locking right but still fulfill that requirement is
to use a process that can call dev_queue_xmit serially over queued
transmissions.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To allow users to choose an elevator algorithm for their particular
workloads, change from a make_request-style driver to an
I/O-request-queue-handler-style driver.
We have to do a couple of things that might be surprising. We manipulate
the page _count directly on the assumption that we still have no guarantee
that users of the block layer are prohibited from submitting bios
containing pages with zero reference counts.[1] If such a prohibition now
exists, I can get rid of the _count manipulation.
Just as before this patch, we still keep track of the sk_buffs that the
network layer still hasn't finished yet and cap the resources we use with
a "pool" of skbs.[2]
Now that the block layer maintains the disk stats, the aoe driver's
diskstats function can go away.
1. https://lkml.org/lkml/2007/3/1/374
2. https://lkml.org/lkml/2007/7/6/241
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the frames the aoe driver uses to track the relationship between bios
and packets more flexible and detached, so that they can be passed to an
"aoe_ktio" thread for completion of I/O.
The frames are handled much like skbs, with a capped amount of
preallocation so that real-world use cases are likely to run smoothly and
degenerate gracefully even under memory pressure.
Decoupling I/O completion from the receive path and serializing it in a
process makes it easier to think about the correctness of the locking in
the driver, especially in the case of a remote MAC address becoming
unusable.
[dan.carpenter@oracle.com: cleanup an allocation a bit]
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tAdd adds the ability to work with large packets composed of a number of
segments, using the scatter gather feature of the block layer (biovecs)
and the network layer (skb frag array). The motivation is the performance
gained by using a packet data payload greater than a page size and by
using the network card's scatter gather feature.
Users of the out-of-tree aoe driver already had these changes, but since
early 2011, they have complained of increased memory utilization and
higher CPU utilization during heavy writes.[1] The commit below appears
related, as it disables scatter gather on non-IP protocols inside the
harmonize_features function, even when the NIC supports sg.
commit f01a5236bd
Author: Jesse Gross <jesse@nicira.com>
Date: Sun Jan 9 06:23:31 2011 +0000
net offloading: Generalize netif_get_vlan_features().
With that regression in place, transmits always linearize sg AoE packets,
but in-kernel users did not have this patch. Before 2.6.38, though, these
changes were working to allow sg to increase performance.
1. http://www.spinics.net/lists/linux-mm/msg15184.html
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add discard support to nbd. If the nbd-server supports discard, it will
send NBD_FLAG_SEND_TRIM to the client. The client will then set the flag
in the kernel via NBD_SET_FLAGS, which tells the kernel to enable discards
for the device (QUEUE_FLAG_DISCARD).
If discard support is enabled, then when the nbd client system receives a
discard request, this will be passed along to the nbd-server. When the
discard request is received by the nbd-server, it will perform:
fallocate(.. FALLOC_FL_PUNCH_HOLE ..)
To punch a hole in the backend storage, which is no longer needed.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a set-flags ioctl, allowing various option flags to be set on an nbd
device. This allows the nbd-client to set the device flags (to enable
read-only mode, or enable discard support, etc.).
Flags are typically specified by the nbd-server. During the negotiation
phase of the nbd connection, the server sends its flags to the client.
The client then uses NBD_SET_FLAGS to inform the kernel of the options.
Also included is a one-line fix to debug output for the set-timeout ioctl.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the single global destination ID counter with per-net allocation
mechanism to allow independent destID management for each available
RapidIO network. Using bitmap based mechanism instead of counters allows
destination ID release and reuse in systems that support hot-swap.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make RIONET driver multi-net safe/capable by introducing per-net lists of
RapidIO network peers. Rework registration of network adapters to support
all available RIO master port devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify mport initialization routine to run the RapidIO discovery process
asynchronously. This allows to have an arbitrary order of enumerating and
discovering ports in systems with multiple RapidIO controllers without
creating a deadlock situation if enumerator port is registered after a
discovering one.
Making netID matching to mportID ensures consistent net ID assignment in
multiport RapidIO systems with asynchronous discovery process (global
counter implementation is affected by race between threads).
[akpm@linux-foundation.org: tweak code layput]
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify handling of device lists to resolve issues caused by using single
global list of RIO devices during enumeration/discovery. The most common
sign of existing issue is incorrect contents of switch routing tables in
systems with multiple mport controllers while single-port configuration
performs as expected.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following set of patches provides modifications targeting support of
multiple RapidIO master port (mport) devices on a CPU-side of
RapidIO-capable board. While the RapidIO subsystem code has definitions
suitable for multi-controller/multi-net support, the existing
implementation cannot be considered ready for multiple mport
configurations.
=========== NOTES: =============
a) The patches below do not address RapidIO side view of multiport
processing elements defined in Part 6 of RapidIO spec Rev.2.1 (section
6.4.1). These devices have Base Device ID CSR (0x60) and Component Tag
CSR (0x6C) shared by all SRIO ports. For example, Freescale's P4080,
P3041 and P5020 have a dual-port SRIO controller implemented according
the specification. Enumeration/discovery of such devices from RapidIO
side may require device-specific fixups.
b) Devices referenced above may also require implementation specific
code to setup a host device ID for mport device. These operations are
not addressed by patches in this package.
=================================
Details about provided patches:
1. Fix blocking wait for discovery ready
While it does not happen on PowerPC based platforms, there is
possibility of stalled CPU warning dump on x86 based platforms that run
RapidIO discovery process if they wait too long for being enumerated.
Currently users can avoid it by disabling the soft-lockup detector
using "nosoftlockup" kernel parameter OR by ensuring that enumeration
is completed before soft-lockup is detected.
This patch eliminates blocking wait and keeps a scheduler running.
It also is required for patch 3 below which introduces asynchronous
discovery process.
2. Use device lists handling on per-net basis
This patch allows to correctly support multiple RapidIO nets and
resolves possible issues caused by using single global list of devices
during RapidIO system enumeration/discovery. The most common sign of
existing issue is incorrect contents of switch routing tables in
systems with multiple mport controllers while single-port configuration
performs as expected.
The patch does not eliminate the global RapidIO device list but
changes some routines in enumeration/discovery to use per-net device
lists instead. This way compatibility with upper layer RIO routines is
preserved.
3. Run discovery as an asynchronous process
This patch modifies RapidIO initialization routine to asynchronously
run the discovery process for each corresponding mport. This allows
having an arbitrary order of enumerating and discovering mports without
creating a deadlock situation if an enumerator port was registered
after a discovering one.
On boards with multiple discovering mports it also eliminates order
dependency between mports and may reduce total time of RapidIO
subsystem initialization.
Making netID matching to mportID ensures consistent netID assignment
in multiport RapidIO systems with asynchronous discovery process
(global counter implementation is affected by race between threads).
4. Rework RIONET to support multiple RIO master ports
In the current version of the driver rionet_probe() has comment "XXX
Make multi-net safe". Now it is a good time to address this comment.
This patch makes RIONET driver multi-net safe/capable by introducing
per-net lists of RapidIO network peers. It also enables to register
network adapters for all available mport devices.
5. Add destination ID allocation mechanism
The patch replaces a single global destination ID counter with
per-net allocation mechanism to allow independent destID management for
each available RapidIO network. Using bitmap based mechanism instead
of counters allows destination ID release and reuse in systems that
support hot-swap.
This patch:
Fix blocking wait loop in the RapidIO discovery routine to avoid warning
dumps about stalled CPU on x86 platforms.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Apply port RX/TX enable operations only to active switch ports.
RapidIO specification (Part 6: LP-Serial Physical Layer) recommends to
keep Output Port Enable (TX) and Input Port Enable (RX) control bits in
disabled state (0b0) after device reset. It also allows to have
implementation specific reset state for these bits.
This patch ensures that TX/RX enable action is applied only to active
switch's ports while preserving an initial state of inactive ones.
This patch is intended to keep inactive switch ports with inbound and
outbound packet transfers disabled to block unexpected packets during hot
insertion event. While it does not fix any visible malfunction it is
intended to prevent such events in future.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Tsi721 routines to support RapidIO subsystem's inbound memory mapping
interface (RapidIO to system's local memory).
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add common inbound memory mapping/unmapping interface. This allows to make
local memory space accessible from the RapidIO side using hardware mapping
capabilities of RapidIO bridging devices. The new interface is intended to
enable data transfers between RapidIO devices in combination with DMA engine
support.
This patch is based on patch submitted by Li Yang <leoli@freescale.com>
(https://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/071210.html)
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify RapidIO mport device name assignment to include device name of PCIe
side of Tsi721 bridge. The new name format is intended to provide
definitive reference between RapidIO and PCIe sides of the bridge in
systems with multiple Tsi721 bridges.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix multicast packet transmit logic to account for repetitive transmission
of single skb:
- correct check for available buffers (this bug may produce NULL pointer
crash dump in case of heavy traffic);
- update skb user count (incorrect user counter causes a warning dump from
net_tx_action routine during multicast transfers in systems with three or
more rionet participants).
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The inclusion of <generated/utsrelease.h> is unnecessary.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This cleanup also fixes the following sparse warning:
fs/proc/root.c:64:45: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The use of if (!head) BUG(); can be replaced with the single line
BUG_ON(!head).
Signed-off-by: Prasad Joshi <prasadjoshi.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Part of the memory will be written twice after this change, but that
should be negligible.
[akpm@linux-foundation.org: fix __proc_create() coding-style issues, remove unneeded zero-initialisations]
Signed-off-by: yan <clouds.yan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
proc_get_inode() obtains the inode via a call to iget_locked().
iget_locked() calls alloc_inode() which will call proc_alloc_inode() which
clears proc_inode.fd, so there is no need to clear this field in
proc_get_inode().
If iget_locked() instead found the inode via find_inode_fast(), that inode
will not have I_NEW set so this change has no effect.
Signed-off-by: yan <clouds.yan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If proc_get_inode() returns NULL then presumably it encountered memory
exhaustion. proc_lookup_de() should return -ENOMEM in this case, not
-EINVAL.
Signed-off-by: yan <clouds.yan@gmail.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This note has the following format:
long count -- how many files are mapped
long page_size -- units for file_ofs
array of [COUNT] elements of
long start
long end
long file_ofs
followed by COUNT filenames in ASCII: "FILE1" NUL "FILE2" NUL...
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: "Jonathan M. Foote" <jmfoote@cert.org>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Existing PRSTATUS note contains only si_signo, si_code, si_errno fields
from the siginfo of the signal which caused core to be dumped.
There are tools which try to analyze crashes for possible security
implications, and they want to use, among other data, si_addr field from
the SIGSEGV.
This patch adds a new elf note, NT_SIGINFO, which contains the complete
siginfo_t of the signal which killed the process.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: "Jonathan M. Foote" <jmfoote@cert.org>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a preparatory patch for the introduction of NT_SIGINFO elf note.
Make the location of compat_siginfo_t uniform across eight architectures
which have it. Now it can be pulled in by including asm/compat.h or
linux/compat.h.
Most of the copies are verbatim. compat_uid[32]_t had to be replaced by
__compat_uid[32]_t. compat_uptr_t had to be moved up before
compat_siginfo_t in asm/compat.h on a several architectures (tile already
had it moved up). compat_sigval_t had to be relocated from linux/compat.h
to asm/compat.h.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: "Jonathan M. Foote" <jmfoote@cert.org>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a preparatory patch for the introduction of NT_SIGINFO elf note.
With this patch we pass "siginfo_t *siginfo" instead of "int signr" to
do_coredump() and put it into coredump_params. It will be used by the
next patch. Most changes are simple s/signr/siginfo->si_signo/.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: "Jonathan M. Foote" <jmfoote@cert.org>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cosmetic. Change setup_new_exec() and task_dumpable() to use
SUID_DUMPABLE_ENABLED for /bin/grep.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some coredump handlers want to create a core file in a way compatible with
standard behavior. Standard behavior with fs.suid_dumpable = 2 is to
create core file with uid=gid=0. However, there was no way for coredump
handler to know that the process being dumped was suid'ed.
This patch adds the new %d specifier for format_corename() which simply
reports __get_dumpable(mm->flags), this is compatible with
/proc/sys/fs/suid_dumpable we already have.
Addresses https://bugzilla.redhat.com/show_bug.cgi?id=787135
Developed during a discussion with Denys Vlasenko.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Alex Kelly <alex.page.kelly@gmail.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Cong Wang <amwang@redhat.com>
Cc: Jiri Moskovcak <jmoskovc@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create a new header file, fs/coredump.h, which contains functions only
used by the new coredump.c. It also moves do_coredump to the
include/linux/coredump.h header file, for consistency.
Signed-off-by: Alex Kelly <alex.page.kelly@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds an expert Kconfig option, CONFIG_COREDUMP, which allows disabling of
core dump. This saves approximately 2.6k in the compiled kernel, and
complements CONFIG_ELF_CORE, which now depends on it.
CONFIG_COREDUMP also disables coredump-related sysctls, except for
suid_dumpable and related functions, which are necessary for ptrace.
[akpm@linux-foundation.org: fix binfmt_aout.c build]
Signed-off-by: Alex Kelly <alex.page.kelly@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces the "whitelist" usage in the code and comments and replace
them by exception list related information.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original model of device_cgroup is having a whitelist where all the
allowed devices are listed. The problem with this approach is that is
impossible to have the case of allowing everything but few devices.
The reason for that lies in the way the whitelist is handled internally:
since there's only a whitelist, the "all devices" entry would have to be
removed and replaced by the entire list of possible devices but the ones
that are being denied. Since dev_t is 32 bits long, representing the allowed
devices as a bitfield is not memory efficient.
This patch replaces the "whitelist" by a "exceptions" list and the default
policy is kept as "deny_all" variable in dev_cgroup structure.
The current interface determines that whenever "a" is written to devices.allow
or devices.deny, the entry masking all devices will be added or removed,
respectively. This behavior is kept and it's what will determine the default
policy:
# cat devices.list
a *:* rwm
# echo a >devices.deny
# cat devices.list
# echo a >devices.allow
# cat devices.list
a *:* rwm
The interface is also preserved. For example, if one wants to block only access
to /dev/null:
# ls -l /dev/null
crw-rw-rw- 1 root root 1, 3 Jul 24 16:17 /dev/null
# echo a >devices.allow
# echo "c 1:3 rwm" >devices.deny
# cat /dev/null
cat: /dev/null: Operation not permitted
# echo >/dev/null
bash: /dev/null: Operation not permitted
mknod /tmp/null c 1 3
mknod: `/tmp/null': Operation not permitted
# echo "c 1:3 r" >devices.allow
# cat /dev/null
# echo >/dev/null
bash: /dev/null: Operation not permitted
mknod /tmp/null c 1 3
mknod: `/tmp/null': Operation not permitted
# echo "c 1:3 rw" >devices.allow
# echo >/dev/null
# cat /dev/null
# mknod /tmp/null c 1 3
mknod: `/tmp/null': Operation not permitted
# echo "c 1:3 rwm" >devices.allow
# echo >/dev/null
# cat /dev/null
# mknod /tmp/null c 1 3
#
Note that I didn't rename the functions/variables in this patch, but in the
next one to make reviewing easier.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function cleans all the items in a whitelist and will be used by the next
patches.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
deny_all will determine if the default policy is to deny all device access
unless for the ones in the exception list.
This variable will be used in the next patches to convert device_cgroup
internally into a default policy + rules.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A section with the name "Example" (case-insensitive) has a special meaning
to kernel-doc. These sections are output using mono-type fonts. However,
leading whitespace is stripped, thus robbing a lot of meaning from this,
as indented code examples will be mangled.
This patch preserves the leading whitespace for "Example" sections. More
accurately, it preserves it for all sections, but removes it later if the
section isn't an "Example" section.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If you have a section named "Example" that contains an empty line,
attempting to generate htmldocs give you the error:
/path/Documentation/DocBook/kernel-api.xml:3455: parser error : Opening and ending tag mismatch: programlisting line 3449 and para
</para><para>
^
/path/Documentation/DocBook/kernel-api.xml:3473: parser error : Opening and ending tag mismatch: para line 3467 and programlisting
</programlisting></informalexample>
^
/path/Documentation/DocBook/kernel-api.xml:3678: parser error : Opening and ending tag mismatch: programlisting line 3672 and para
</para><para>
^
/path/Documentation/DocBook/kernel-api.xml:3701: parser error : Opening and ending tag mismatch: para line 3690 and programlisting
</programlisting></informalexample>
^
unable to parse
/path/Documentation/DocBook/kernel-api.xml
Essentially, the script attempts to close a <programlisting> with a
closing tag for a <para> block. This patch corrects the problem by
simply not outputting anything extra when we're dumping pre-formatted
text, since the empty line will be rendered correctly anyway.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prior to this patch the following code breaks:
/**
* multiline_example - this breaks kernel-doc
*/
#define multiline_example( \
myparam)
Producing this error:
Error(somefile.h:983): cannot understand prototype: 'multiline_example( \ '
This patch fixes the issue by appending all lines ending in a blackslash
(optionally followed by whitespace), removing the backslash and any
whitespace after it prior to appending (just like the C pre-processor
would).
This fixes a break in kerel-doc introduced by the additions to rbtree.h.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
