One way of utilizing DSA is by cascading switches which do not all have
compatible taggers. Consider the following real-life topology:
+---------------------------------------------------------------+
| LS1028A |
| +------------------------------+ |
| | DSA master for Felix | |
| |(internal ENETC port 2: eno2))| |
| +------------+------------------------------+-------------+ |
| | Felix embedded L2 switch | |
| | | |
| | +--------------+ +--------------+ +--------------+ | |
| | |DSA master for| |DSA master for| |DSA master for| | |
| | | SJA1105 1 | | SJA1105 2 | | SJA1105 3 | | |
| | |(Felix port 1)| |(Felix port 2)| |(Felix port 3)| | |
+--+-+--------------+---+--------------+---+--------------+--+--+
+-----------------------+ +-----------------------+ +-----------------------+
| SJA1105 switch 1 | | SJA1105 switch 2 | | SJA1105 switch 3 |
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
|sw1p0|sw1p1|sw1p2|sw1p3| |sw2p0|sw2p1|sw2p2|sw2p3| |sw3p0|sw3p1|sw3p2|sw3p3|
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
The above can be described in the device tree as follows (obviously not
complete):
mscc_felix {
dsa,member = <0 0>;
ports {
port@4 {
ethernet = <&enetc_port2>;
};
};
};
sja1105_switch1 {
dsa,member = <1 1>;
ports {
port@4 {
ethernet = <&mscc_felix_port1>;
};
};
};
sja1105_switch2 {
dsa,member = <2 2>;
ports {
port@4 {
ethernet = <&mscc_felix_port2>;
};
};
};
sja1105_switch3 {
dsa,member = <3 3>;
ports {
port@4 {
ethernet = <&mscc_felix_port3>;
};
};
};
Basically we instantiate one DSA switch tree for every hardware switch
in the system, but we still give them globally unique switch IDs (will
come back to that later). Having 3 disjoint switch trees makes the
tagger drivers "just work", because net devices are registered for the
3 Felix DSA master ports, and they are also DSA slave ports to the ENETC
port. So packets received on the ENETC port are stripped of their
stacked DSA tags one by one.
Currently, hardware bridging between ports on the same sja1105 chip is
possible, but switching between sja1105 ports on different chips is
handled by the software bridge. This is fine, but we can do better.
In fact, the dsa_8021q tag used by sja1105 is compatible with cascading.
In other words, a sja1105 switch can correctly parse and route a packet
containing a dsa_8021q tag. So if we could enable hardware bridging on
the Felix DSA master ports, cross-chip bridging could be completely
offloaded.
Such as system would be used as follows:
ip link add dev br0 type bridge && ip link set dev br0 up
for port in sw0p0 sw0p1 sw0p2 sw0p3 \
sw1p0 sw1p1 sw1p2 sw1p3 \
sw2p0 sw2p1 sw2p2 sw2p3; do
ip link set dev $port master br0
done
The above makes switching between ports on the same row be performed in
hardware, and between ports on different rows in software. Now assume
the Felix switch ports are called swp0, swp1, swp2. By running the
following extra commands:
ip link add dev br1 type bridge && ip link set dev br1 up
for port in swp0 swp1 swp2; do
ip link set dev $port master br1
done
the CPU no longer sees packets which traverse sja1105 switch boundaries
and can be forwarded directly by Felix. The br1 bridge would not be used
for any sort of traffic termination.
For this to work, we need to give drivers an opportunity to listen for
bridging events on DSA trees other than their own, and pass that other
tree index as argument. I have made the assumption, for the moment, that
the other existing DSA notifiers don't need to be broadcast to other
trees. That assumption might turn out to be incorrect. But in the
meantime, introduce a dsa_broadcast function, similar in purpose to
dsa_port_notify, which is used only by the bridging notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 8db0a2ee2c ("net: bridge: reject DSA-enabled master netdevices
as bridge members") added a special check in br_if.c in order to check
for a DSA master network device with a tagging protocol configured. This
was done because back then, such devices, once enslaved in a bridge
would become inoperative and would not pass DSA tagged traffic anymore
due to br_handle_frame returning RX_HANDLER_CONSUMED.
But right now we have valid use cases which do require bridging of DSA
masters. One such example is when the DSA master ports are DSA switch
ports themselves (in a disjoint tree setup). This should be completely
equivalent, functionally speaking, from having multiple DSA switches
hanging off of the ports of a switchdev driver. So we should allow the
enslaving of DSA tagged master network devices.
Instead of the regular br_handle_frame(), install a new function
br_handle_frame_dummy() on these DSA masters, which returns
RX_HANDLER_PASS in order to call into the DSA specific tagging protocol
handlers, and lift the restriction from br_add_if.
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Parts of rpc_free_client() were recently moved to
a separate rpc_free_clent_work(). This introduced
a use-after-free as rpc_clnt_remove_pipedir() calls
rpc_net_ns(), and that uses clnt->cl_xprt which has already
been freed.
So move the call to xprt_put() after the call to
rpc_clnt_remove_pipedir().
Reported-by: syzbot+22b5ef302c7c40d94ea8@syzkaller.appspotmail.com
Fixes: 7c4310ff56 ("SUNRPC: defer slow parts of rpc_free_client() to a workqueue.")
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
gcc-10 warns around a suspicious access to an empty struct member:
net/netfilter/nf_conntrack_core.c: In function '__nf_conntrack_alloc':
net/netfilter/nf_conntrack_core.c:1522:9: warning: array subscript 0 is outside the bounds of an interior zero-length array 'u8[0]' {aka 'unsigned char[0]'} [-Wzero-length-bounds]
1522 | memset(&ct->__nfct_init_offset[0], 0,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from net/netfilter/nf_conntrack_core.c:37:
include/net/netfilter/nf_conntrack.h:90:5: note: while referencing '__nfct_init_offset'
90 | u8 __nfct_init_offset[0];
| ^~~~~~~~~~~~~~~~~~
The code is correct but a bit unusual. Rework it slightly in a way that
does not trigger the warning, using an empty struct instead of an empty
array. There are probably more elegant ways to do this, but this is the
smallest change.
Fixes: c41884ce05 ("netfilter: conntrack: avoid zeroing timer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Given that it takes time to run a cable test, send a notify message at
the start, as well as when it is completed.
v3:
EMSGSIZE when ethnl_bcastmsg_put() fails
Print an error message on failure, since this is a void function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PHY drivers can use these helpers for reporting the results. The
results get translated into netlink attributes which are added to the
pre-allocated skbuf.
v3:
Poison phydev->skb
Return -EMSGSIZE when ethnl_bcastmsg_put() fails
Return valid error code when nla_nest_start() fails
Use u8 for results
Actually put u32 length into message
v4:
s/ENOTSUPP/EOPNOTSUPP/g
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide infrastructure for PHY drivers to report the cable test
results. A netlink skb is associated to the phydev. Helpers will be
added which can add results to this skb. Once the test has finished
the results are sent to user space.
When netlink ethtool is not part of the kernel configuration stubs are
provided. It is also impossible to trigger a cable test, so the error
code returned by the alloc function is of no consequence.
v2:
Include the status complete in the netlink notification message
v4:
Replace -EINVAL with -EMSGSIZE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make some helpers for building ethtool netlink messages available
outside the compilation unit, so they can be used for building
messages which are not simple get/set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new ethtool netlink calls to trigger the starting of a PHY cable
test.
Add Kconfig'ury to ETHTOOL_NETLINK so that PHYLIB is not a module when
ETHTOOL_NETLINK is builtin, which would result in kernel linking errors.
v2:
Remove unwanted white space change
Remove ethnl_cable_test_act_ops and use doit handler
Rename cable_test_set_policy cable_test_act_policy
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY
v3:
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY from documentation
Remove unused cable_test_get_policy
Add Reviewed-by tags
v4:
Remove unwanted blank line
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If systemd is configured to use hybrid mode which enables the use of
both cgroup v1 and v2, systemd will create new cgroup on both the default
root (v2) and netprio_cgroup hierarchy (v1) for a new session and attach
task to the two cgroups. If the task does some network thing then the v2
cgroup can never be freed after the session exited.
One of our machines ran into OOM due to this memory leak.
In the scenario described above when sk_alloc() is called
cgroup_sk_alloc() thought it's in v2 mode, so it stores
the cgroup pointer in sk->sk_cgrp_data and increments
the cgroup refcnt, but then sock_update_netprioidx()
thought it's in v1 mode, so it stores netprioidx value
in sk->sk_cgrp_data, so the cgroup refcnt will never be freed.
Currently we do the mode switch when someone writes to the ifpriomap
cgroup control file. The easiest fix is to also do the switch when
a task is attached to a new cgroup.
Fixes: bd1060a1d6 ("sock, cgroup: add sock->sk_cgroup")
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Tested-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added netlink and ipv6_route targets, using
the same seq_ops (except show() and minor changes for stop())
for /proc/net/{netlink,ipv6_route}.
The net namespace for these targets are the current net
namespace at file open stage, similar to
/proc/net/{netlink,ipv6_route} reference counting
the net namespace at seq_file open stage.
Since module is not supported for now, ipv6_route is
supported only if the IPV6 is built-in, i.e., not compiled
as a module. The restriction can be lifted once module
is properly supported for bpf_iter.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175910.2476329-1-yhs@fb.com
This merge includes updates to bonding driver needed for the rdma stack,
to avoid conflicts with the RDMA branch.
Maor Gottlieb Says:
====================
Bonding: Add support to get xmit slave
The following series adds support to get the LAG master xmit slave by
introducing new .ndo - ndo_get_xmit_slave. Every LAG module can
implement it and it first implemented in the bond driver.
This is follow-up to the RFC discussion [1].
The main motivation for doing this is for drivers that offload part
of the LAG functionality. For example, Mellanox Connect-X hardware
implements RoCE LAG which selects the TX affinity when the resources
are created and port is remapped when it goes down.
The first part of this patchset introduces the new .ndo and add the
support to the bonding module.
The second part adds support to get the RoCE LAG xmit slave by building
skb of the RoCE packet based on the AH attributes and call to the new
.ndo.
The third part change the mlx5 driver driver to set the QP's affinity
port according to the slave which found by the .ndo.
====================
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In commit b406472b5a ("net: ipv4: avoid mixed n_redirects and
rate_tokens usage") I missed the fact that a 0 'rate_tokens' will
bypass the backoff algorithm.
Since rate_tokens is cleared after a redirect silence, and never
incremented on redirects, if the host keeps receiving packets
requiring redirect it will reply ignoring the backoff.
Additionally, the 'rate_last' field will be updated with the
cadence of the ingress packet requiring redirect. If that rate is
high enough, that will prevent the host from generating any
other kind of ICMP messages
The check for a zero 'rate_tokens' value was likely a shortcut
to avoid the more complex backoff algorithm after a redirect
silence period. Address the issue checking for 'n_redirects'
instead, which is incremented on successful redirect, and
does not interfere with other ICMP replies.
Fixes: b406472b5a ("net: ipv4: avoid mixed n_redirects and rate_tokens usage")
Reported-and-tested-by: Colin Walters <walters@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We currently have to adjust ipv6 route gc_thresh/max_size depending
on number of cpus on a server, this makes very little sense.
If the kernels sets /proc/sys/net/ipv6/route/gc_thresh to 1024
and /proc/sys/net/ipv6/route/max_size to 4096, then we better
not track the percpu dst that our implementation uses.
Only routes not added (directly or indirectly) by the admin
should be tracked and limited.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: Maciej Żenczykowski <maze@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The type of dispatch is u8 which is always '<=' 0xff, so the
dispatch <= 0xff is always true, we can remove this comparison.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
percpu_counter_add() uses a default batch size which is quite big
on platforms with 256 cpus. (2*256 -> 512)
This means dst_entries_get_fast() can be off by +/- 2*(nr_cpus^2)
(131072 on servers with 256 cpus)
Reduce the batch size to something more reasonable, and
add logic to ip6_dst_gc() to call dst_entries_get_slow()
before calling the _very_ expensive fib6_run_gc() function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2020-05-09
The following pull-request contains BPF updates for your *net* tree.
We've added 4 non-merge commits during the last 9 day(s) which contain
a total of 4 files changed, 11 insertions(+), 6 deletions(-).
The main changes are:
1) Fix msg_pop_data() helper incorrectly setting an sge length in some
cases as well as fixing bpf_tcp_ingress() wrongly accounting bytes
in sg.size, from John Fastabend.
2) Fix to return an -EFAULT error when copy_to_user() of the value
fails in map_lookup_and_delete_elem(), from Wei Yongjun.
3) Fix sk_psock refcnt leak in tcp_bpf_recvmsg(), from Xiyu Yang.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The stated intent of the original commit is to is to "return the timestamp
corresponding to the highest sequence number data returned." The current
implementation returns the timestamp for the last byte of the last fully
read skb, which is not necessarily the last byte in the recv buffer. This
patch converts behavior to the original definition, and to the behavior of
the previous draft versions of commit 98aaa913b4 ("tcp: Extend
SOF_TIMESTAMPING_RX_SOFTWARE to TCP recvmsg") which also match this
behavior.
Fixes: 98aaa913b4 ("tcp: Extend SOF_TIMESTAMPING_RX_SOFTWARE to TCP recvmsg")
Co-developed-by: Iris Liu <iris@onechronos.com>
Signed-off-by: Iris Liu <iris@onechronos.com>
Signed-off-by: Kelly Littlepage <kelly@onechronos.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We want to have a tighter control on what ports we bind to in
the BPF_CGROUP_INET{4,6}_CONNECT hooks even if it means
connect() becomes slightly more expensive. The expensive part
comes from the fact that we now need to call inet_csk_get_port()
that verifies that the port is not used and allocates an entry
in the hash table for it.
Since we can't rely on "snum || !bind_address_no_port" to prevent
us from calling POST_BIND hook anymore, let's add another bind flag
to indicate that the call site is BPF program.
v5:
* fix wrong AF_INET (should be AF_INET6) in the bpf program for v6
v3:
* More bpf_bind documentation refinements (Martin KaFai Lau)
* Add UDP tests as well (Martin KaFai Lau)
* Don't start the thread, just do socket+bind+listen (Martin KaFai Lau)
v2:
* Update documentation (Andrey Ignatov)
* Pass BIND_FORCE_ADDRESS_NO_PORT conditionally (Andrey Ignatov)
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200508174611.228805-5-sdf@google.com
The intent is to add an additional bind parameter in the next commit.
Instead of adding another argument, let's convert all existing
flag arguments into an extendable bit field.
No functional changes.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200508174611.228805-4-sdf@google.com
syzbot managed to trigger a recursive NETDEV_FEAT_CHANGE event
between bonding master and slave. I managed to find a reproducer
for this:
ip li set bond0 up
ifenslave bond0 eth0
brctl addbr br0
ethtool -K eth0 lro off
brctl addif br0 bond0
ip li set br0 up
When a NETDEV_FEAT_CHANGE event is triggered on a bonding slave,
it captures this and calls bond_compute_features() to fixup its
master's and other slaves' features. However, when syncing with
its lower devices by netdev_sync_lower_features() this event is
triggered again on slaves when the LRO feature fails to change,
so it goes back and forth recursively until the kernel stack is
exhausted.
Commit 17b85d29e8 intentionally lets __netdev_update_features()
return -1 for such a failure case, so we have to just rely on
the existing check inside netdev_sync_lower_features() and skip
NETDEV_FEAT_CHANGE event only for this specific failure case.
Fixes: fd867d51f8 ("net/core: generic support for disabling netdev features down stack")
Reported-by: syzbot+e73ceacfd8560cc8a3ca@syzkaller.appspotmail.com
Reported-by: syzbot+c2fb6f9ddcea95ba49b5@syzkaller.appspotmail.com
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jann Horn <jannh@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sch_fq has horizon feature, we want to allow QUIC/UDP applications
to use EDT model so that pacing can be offloaded to the kernel (sch_fq)
or the NIC.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a subflow is created via mptcp_subflow_create_socket(),
a new 'struct socket' is allocated, with a new i_ino value.
When inspecting TCP sockets via the procfs and or the diag
interface, the above ones are not related to the process owning
the MPTCP master socket, even if they are a logical part of it
('ss -p' shows an empty process field)
Additionally, subflows created by the path manager get
the uid/gid from the running workqueue.
Subflows are part of the owning MPTCP master socket, let's
adjust the vfs info to reflect this.
After this patch, 'ss' correctly displays subflows as belonging
to the msk socket creator.
Fixes: 2303f994b3 ("mptcp: Associate MPTCP context with TCP socket")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netpoll_send_skb() callers seem to leak skb if
the np pointer is NULL. While this should not happen, we
can make the code more robust.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some callers want to know if the packet has been sent or
dropped, to inform upper stacks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to inline this helper, as we intend to add more
code in this function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netpoll_send_skb_on_dev() can get the device pointer directly from np->dev
Rename it to __netpoll_send_skb()
Following patch will move netpoll_send_skb() out-of-line.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/smc/smc_llc.c: In function 'smc_llc_cli_conf_link':
net/smc/smc_llc.c:753:31: warning:
variable 'del_llc' set but not used [-Wunused-but-set-variable]
struct smc_llc_msg_del_link *del_llc;
^
net/smc/smc_llc.c: In function 'smc_llc_process_srv_delete_link':
net/smc/smc_llc.c:1311:33: warning:
variable 'del_llc_resp' set but not used [-Wunused-but-set-variable]
struct smc_llc_msg_del_link *del_llc_resp;
^
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so tcp_is_sack/reno checks are removed from tcp_mark_head_lost.
Signed-off-by: zhang kai <zhangkaiheb@126.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NL_SET_ERR_MSG_MOD macro is used to report a string describing an
error message to userspace via the netlink extended ACK structure. It
should not have a trailing newline.
Add a cocci script which catches cases where the newline marker is
present. Using this script, fix the handful of cases which accidentally
included a trailing new line.
I couldn't figure out a way to get a patch mode working, so this script
only implements context, report, and org.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN frame is being sent, hsr calls WARN_ONCE() because hsr doesn't
support VLAN. But using WARN_ONCE() is overdoing.
Using netdev_warn_once() is enough.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As its implementation shows, this is synonimous with calling
dsa_slave_dev_check followed by dsa_slave_to_port, so it is quite simple
already and provides functionality which is already there.
However there is now a need for these functions outside dsa_priv.h, for
example in drivers that perform mirroring and redirection through
tc-flower offloads (they are given raw access to the flow_cls_offload
structure), where they need to call this function on act->dev.
But simply exporting dsa_slave_to_port would make it non-inline and
would result in an extra function call in the hotpath, as can be seen
for example in sja1105:
Before:
000006dc <sja1105_xmit>:
{
6dc: e92d4ff0 push {r4, r5, r6, r7, r8, r9, sl, fp, lr}
6e0: e1a04000 mov r4, r0
6e4: e591958c ldr r9, [r1, #1420] ; 0x58c <- Inline dsa_slave_to_port
6e8: e1a05001 mov r5, r1
6ec: e24dd004 sub sp, sp, #4
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
6f0: e1c901d8 ldrd r0, [r9, #24]
6f4: ebfffffe bl 0 <dsa_8021q_tx_vid>
6f4: R_ARM_CALL dsa_8021q_tx_vid
u8 pcp = netdev_txq_to_tc(netdev, queue_mapping);
6f8: e1d416b0 ldrh r1, [r4, #96] ; 0x60
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
6fc: e1a08000 mov r8, r0
After:
000006e4 <sja1105_xmit>:
{
6e4: e92d4ff0 push {r4, r5, r6, r7, r8, r9, sl, fp, lr}
6e8: e1a04000 mov r4, r0
6ec: e24dd004 sub sp, sp, #4
struct dsa_port *dp = dsa_slave_to_port(netdev);
6f0: e1a00001 mov r0, r1
{
6f4: e1a05001 mov r5, r1
struct dsa_port *dp = dsa_slave_to_port(netdev);
6f8: ebfffffe bl 0 <dsa_slave_to_port>
6f8: R_ARM_CALL dsa_slave_to_port
6fc: e1a09000 mov r9, r0
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
700: e1c001d8 ldrd r0, [r0, #24]
704: ebfffffe bl 0 <dsa_8021q_tx_vid>
704: R_ARM_CALL dsa_8021q_tx_vid
Because we want to avoid possible performance regressions, introduce
this new function which is designed to be public.
Suggested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 19bda36c42:
| ipv6: add mtu lock check in __ip6_rt_update_pmtu
|
| Prior to this patch, ipv6 didn't do mtu lock check in ip6_update_pmtu.
| It leaded to that mtu lock doesn't really work when receiving the pkt
| of ICMPV6_PKT_TOOBIG.
|
| This patch is to add mtu lock check in __ip6_rt_update_pmtu just as ipv4
| did in __ip_rt_update_pmtu.
The above reasoning is incorrect. IPv6 *requires* icmp based pmtu to work.
There's already a comment to this effect elsewhere in the kernel:
$ git grep -p -B1 -A3 'RTAX_MTU lock'
net/ipv6/route.c=4813=
static int rt6_mtu_change_route(struct fib6_info *f6i, void *p_arg)
...
/* In IPv6 pmtu discovery is not optional,
so that RTAX_MTU lock cannot disable it.
We still use this lock to block changes
caused by addrconf/ndisc.
*/
This reverts to the pre-4.9 behaviour.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Fixes: 19bda36c42 ("ipv6: add mtu lock check in __ip6_rt_update_pmtu")
Signed-off-by: David S. Miller <davem@davemloft.net>
IPC Router protocol is also used by external modems for exchanging the QMI
messages. Hence, it doesn't always depend on Qualcomm platforms. One such
instance is the QCA6390 WLAN device connected to x86 machine.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MHI is the transport layer used for communicating to the external modems.
Hence, this commit adds MHI transport layer support to QRTR for
transferring the QMI messages over IPC Router.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix reference count leaks in various parts of batman-adv, from Xiyu
Yang.
2) Update NAT checksum even when it is zero, from Guillaume Nault.
3) sk_psock reference count leak in tls code, also from Xiyu Yang.
4) Sanity check TCA_FQ_CODEL_DROP_BATCH_SIZE netlink attribute in
fq_codel, from Eric Dumazet.
5) Fix panic in choke_reset(), also from Eric Dumazet.
6) Fix VLAN accel handling in bnxt_fix_features(), from Michael Chan.
7) Disallow out of range quantum values in sch_sfq, from Eric Dumazet.
8) Fix crash in x25_disconnect(), from Yue Haibing.
9) Don't pass pointer to local variable back to the caller in
nf_osf_hdr_ctx_init(), from Arnd Bergmann.
10) Wireguard should use the ECN decap helper functions, from Toke
Høiland-Jørgensen.
11) Fix command entry leak in mlx5 driver, from Moshe Shemesh.
12) Fix uninitialized variable access in mptcp's
subflow_syn_recv_sock(), from Paolo Abeni.
13) Fix unnecessary out-of-order ingress frame ordering in macsec, from
Scott Dial.
14) IPv6 needs to use a global serial number for dst validation just
like ipv4, from David Ahern.
15) Fix up PTP_1588_CLOCK deps, from Clay McClure.
16) Missing NLM_F_MULTI flag in gtp driver netlink messages, from
Yoshiyuki Kurauchi.
17) Fix a regression in that dsa user port errors should not be fatal,
from Florian Fainelli.
18) Fix iomap leak in enetc driver, from Dejin Zheng.
19) Fix use after free in lec_arp_clear_vccs(), from Cong Wang.
20) Initialize protocol value earlier in neigh code paths when
generating events, from Roman Mashak.
21) netdev_update_features() must be called with RTNL mutex in macsec
driver, from Antoine Tenart.
22) Validate untrusted GSO packets even more strictly, from Willem de
Bruijn.
23) Wireguard decrypt worker needs a cond_resched(), from Jason
Donenfeld.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
net: flow_offload: skip hw stats check for FLOW_ACTION_HW_STATS_DONT_CARE
MAINTAINERS: put DYNAMIC INTERRUPT MODERATION in proper order
wireguard: send/receive: use explicit unlikely branch instead of implicit coalescing
wireguard: selftests: initalize ipv6 members to NULL to squelch clang warning
wireguard: send/receive: cond_resched() when processing worker ringbuffers
wireguard: socket: remove errant restriction on looping to self
wireguard: selftests: use normal kernel stack size on ppc64
net: ethernet: ti: am65-cpsw-nuss: fix irqs type
ionic: Use debugfs_create_bool() to export bool
net: dsa: Do not leave DSA master with NULL netdev_ops
net: dsa: remove duplicate assignment in dsa_slave_add_cls_matchall_mirred
net: stricter validation of untrusted gso packets
seg6: fix SRH processing to comply with RFC8754
net: mscc: ocelot: ANA_AUTOAGE_AGE_PERIOD holds a value in seconds, not ms
net: dsa: ocelot: the MAC table on Felix is twice as large
net: dsa: sja1105: the PTP_CLK extts input reacts on both edges
selftests: net: tcp_mmap: fix SO_RCVLOWAT setting
net: hsr: fix incorrect type usage for protocol variable
net: macsec: fix rtnl locking issue
net: mvpp2: cls: Prevent buffer overflow in mvpp2_ethtool_cls_rule_del()
...
This patch adds FLOW_ACTION_HW_STATS_DONT_CARE which tells the driver
that the frontend does not need counters, this hw stats type request
never fails. The FLOW_ACTION_HW_STATS_DISABLED type explicitly requests
the driver to disable the stats, however, if the driver cannot disable
counters, it bails out.
TCA_ACT_HW_STATS_* maintains the 1:1 mapping with FLOW_ACTION_HW_STATS_*
except by disabled which is mapped to FLOW_ACTION_HW_STATS_DISABLED
(this is 0 in tc). Add tc_act_hw_stats() to perform the mapping between
TCA_ACT_HW_STATS_* and FLOW_ACTION_HW_STATS_*.
Fixes: 319a1d1947 ("flow_offload: check for basic action hw stats type")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ndo_get_phys_port_name() for the CPU port was added we introduced
an early check for when the DSA master network device in
dsa_master_ndo_setup() already implements ndo_get_phys_port_name(). When
we perform the teardown operation in dsa_master_ndo_teardown() we would
not be checking that cpu_dp->orig_ndo_ops was successfully allocated and
non-NULL initialized.
With network device drivers such as virtio_net, this leads to a NPD as
soon as the DSA switch hanging off of it gets torn down because we are
now assigning the virtio_net device's netdev_ops a NULL pointer.
Fixes: da7b9e9b00 ("net: dsa: Add ndo_get_phys_port_name() for CPU port")
Reported-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was caused by a poor merge conflict resolution on my side. The
"act = &cls->rule->action.entries[0];" assignment was already present in
the code prior to the patch mentioned below.
Fixes: e13c207528 ("net: dsa: refactor matchall mirred action to separate function")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As hinted in prior change ("tcp: refine tcp_pacing_delay()
for very low pacing rates"), it is probably best arming
the xmit timer only when all the packets have been scheduled,
rather than when the head of rtx queue has been re-sent.
This does matter for flows having extremely low pacing rates,
since their tp->tcp_wstamp_ns could be far in the future.
Note that the regular xmit path has a stronger limit
in tcp_small_queue_check(), meaning it is less likely to
go beyond the pacing horizon.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of horizon feature to sch_fq, we noticed some
suboptimal behavior of extremely low pacing rate TCP flows, especially
when TCP is not aware of a drop happening in lower stacks.
Back in commit 3f80e08f40 ("tcp: add tcp_reset_xmit_timer() helper"),
tcp_pacing_delay() was added to estimate an extra delay to add to standard
rto timers.
This patch removes the skb argument from this helper and
tcp_reset_xmit_timer() because it makes more sense to simply
consider the time at which next packet is allowed to be sent,
instead of the time of whatever packet has been sent.
This avoids arming RTO timer too soon and removes
spurious horizon drops.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Segment Routing Header (SRH) which defines the SRv6 dataplane is defined
in RFC8754.
RFC8754 (section 4.1) defines the SR source node behavior which encapsulates
packets into an outer IPv6 header and SRH. The SR source node encodes the
full list of Segments that defines the packet path in the SRH. Then, the
first segment from list of Segments is copied into the Destination address
of the outer IPv6 header and the packet is sent to the first hop in its path
towards the destination.
If the Segment list has only one segment, the SR source node can omit the SRH
as he only segment is added in the destination address.
RFC8754 (section 4.1.1) defines the Reduced SRH, when a source does not
require the entire SID list to be preserved in the SRH. A reduced SRH does
not contain the first segment of the related SR Policy (the first segment is
the one already in the DA of the IPv6 header), and the Last Entry field is
set to n-2, where n is the number of elements in the SR Policy.
RFC8754 (section 4.3.1.1) defines the SRH processing and the logic to
validate the SRH (S09, S10, S11) which works for both reduced and
non-reduced behaviors.
This patch updates seg6_validate_srh() to validate the SRH as per RFC8754.
Signed-off-by: Ahmed Abdelsalam <ahabdels@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the upcoming rev of RFC4941 (IPv6 temporary addresses):
https://tools.ietf.org/html/draft-ietf-6man-rfc4941bis-09
* Reduces the default Valid Lifetime to 2 days
The number of extra addresses employed when Valid Lifetime was
7 days exacerbated the stress caused on network
elements/devices. Additionally, the motivation for temporary
addresses is indeed privacy and reduced exposure. With a
default Valid Lifetime of 7 days, an address that becomes
revealed by active communication is reachable and exposed for
one whole week. The only use case for a Valid Lifetime of 7
days could be some application that is expecting to have long
lived connections. But if you want to have a long lived
connections, you shouldn't be using a temporary address in the
first place. Additionally, in the era of mobile devices, general
applications should nevertheless be prepared and robust to
address changes (e.g. nodes swap wifi <-> 4G, etc.)
* Employs different IIDs for different prefixes
To avoid network activity correlation among addresses configured
for different prefixes
* Uses a simpler algorithm for IID generation
No need to store "history" anywhere
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse checker warning:-
net/hsr/hsr_slave.c:38:18: warning: incorrect type in assignment (different base types)
net/hsr/hsr_slave.c:38:18: expected unsigned short [unsigned] [usertype] protocol
net/hsr/hsr_slave.c:38:18: got restricted __be16 [usertype] h_proto
net/hsr/hsr_slave.c:39:25: warning: restricted __be16 degrades to integer
net/hsr/hsr_slave.c:39:57: warning: restricted __be16 degrades to integer
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
net/bridge/br_private.h:1334:8-9: WARNING: return of 0/1 in function
'br_mrp_enabled' with return type bool
Fixes: 6536993371 ("bridge: mrp: Integrate MRP into the bridge")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bpf_tcp_ingress we used apply_bytes to subtract bytes from sg.size
which is used to track total bytes in a message. But this is not
correct because apply_bytes is itself modified in the main loop doing
the mem_charge.
Then at the end of this we have sg.size incorrectly set and out of
sync with actual sk values. Then we can get a splat if we try to
cork the data later and again try to redirect the msg to ingress. To
fix instead of trying to track msg.size do the easy thing and include
it as part of the sk_msg_xfer logic so that when the msg is moved the
sg.size is always correct.
To reproduce the below users will need ingress + cork and hit an
error path that will then try to 'free' the skmsg.
[ 173.699981] BUG: KASAN: null-ptr-deref in sk_msg_free_elem+0xdd/0x120
[ 173.699987] Read of size 8 at addr 0000000000000008 by task test_sockmap/5317
[ 173.700000] CPU: 2 PID: 5317 Comm: test_sockmap Tainted: G I 5.7.0-rc1+ #43
[ 173.700005] Hardware name: Dell Inc. Precision 5820 Tower/002KVM, BIOS 1.9.2 01/24/2019
[ 173.700009] Call Trace:
[ 173.700021] dump_stack+0x8e/0xcb
[ 173.700029] ? sk_msg_free_elem+0xdd/0x120
[ 173.700034] ? sk_msg_free_elem+0xdd/0x120
[ 173.700042] __kasan_report+0x102/0x15f
[ 173.700052] ? sk_msg_free_elem+0xdd/0x120
[ 173.700060] kasan_report+0x32/0x50
[ 173.700070] sk_msg_free_elem+0xdd/0x120
[ 173.700080] __sk_msg_free+0x87/0x150
[ 173.700094] tcp_bpf_send_verdict+0x179/0x4f0
[ 173.700109] tcp_bpf_sendpage+0x3ce/0x5d0
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/158861290407.14306.5327773422227552482.stgit@john-Precision-5820-Tower
When sk_msg_pop() is called where the pop operation is working on
the end of a sge element and there is no additional trailing data
and there _is_ data in front of pop, like the following case,
|____________a_____________|__pop__|
We have out of order operations where we incorrectly set the pop
variable so that instead of zero'ing pop we incorrectly leave it
untouched, effectively. This can cause later logic to shift the
buffers around believing it should pop extra space. The result is
we have 'popped' more data then we expected potentially breaking
program logic.
It took us a while to hit this case because typically we pop headers
which seem to rarely be at the end of a scatterlist elements but
we can't rely on this.
Fixes: 7246d8ed4d ("bpf: helper to pop data from messages")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/158861288359.14306.7654891716919968144.stgit@john-Precision-5820-Tower
When a new neighbor entry has been added, event is generated but it does not
include protocol, because its value is assigned after the event notification
routine has run, so move protocol assignment code earlier.
Fixes: df9b0e30d4 ("neighbor: Add protocol attribute")
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Type I ERSPAN frame format is based on the barebones
IP + GRE(4-byte) encapsulation on top of the raw mirrored frame.
Both type I and II use 0x88BE as protocol type. Unlike type II
and III, no sequence number or key is required.
To creat a type I erspan tunnel device:
$ ip link add dev erspan11 type erspan \
local 172.16.1.100 remote 172.16.1.200 \
erspan_ver 0
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bac6de7b63 ("net/smc: eliminate cursor read and write calls")
left behind this.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print to system log when SMC links are available or go down, link group
state changes or pnetids are applied to and removed from devices.
The log entries are triggered by either user configuration actions or
adapter activation/deactivation events and are not expected to happen
often. The entries help SMC users to keep track of the SMC link group
status and to detect when actions are needed (like to add replacements
for failed adapters).
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no callers in-tree anymore since commit 5952fde10c ("net:
sched: choke: remove dead filter classify code")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unnecessary member of address in struct xdp_umem as it is
only used during the umem registration. No need to carry this around
as it is not used during run-time nor when unregistering the umem.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/bpf/1588599232-24897-3-git-send-email-magnus.karlsson@intel.com
Change two variables names so that it is clearer what they
represent. The first one is xsk_list that in fact only contains the
list of AF_XDP sockets with a Tx component. Change this to xsk_tx_list
for improved clarity. The second variable is size in the ring
structure. One might think that this is the size of the ring, but it
is in fact the size of the umem, copied into the ring structure to
improve performance. Rename this variable umem_size to avoid any
confusion.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/bpf/1588599232-24897-2-git-send-email-magnus.karlsson@intel.com
This patch reverts the folowing commits:
commit 064ff66e2b
"bonding: add missing netdev_update_lockdep_key()"
commit 53d374979e
"net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()"
commit 1f26c0d3d2
"net: fix kernel-doc warning in <linux/netdevice.h>"
commit ab92d68fc2
"net: core: add generic lockdep keys"
but keeps the addr_list_lock_key because we still lock
addr_list_lock nestedly on stack devices, unlikely xmit_lock
this is safe because we don't take addr_list_lock on any fast
path.
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gengming reported a UAF in lec_arp_clear_vccs(),
where we add a vcc socket to an entry in a per-device
list but free the socket without removing it from the
list when vcc->dev is NULL.
We need to call lec_vcc_close() to search and remove
those entries contain the vcc being destroyed. This can
be done by calling vcc->push(vcc, NULL) unconditionally
in vcc_destroy_socket().
Another issue discovered by Gengming's reproducer is
the vcc->dev may point to the static device lecatm_dev,
for which we don't need to register/unregister device,
so we can just check for vcc->dev->ops->owner.
Reported-by: Gengming Liu <l.dmxcsnsbh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently users have to choose a free snapshot id before
calling DEVLINK_CMD_REGION_NEW. This is potentially racy
and inconvenient.
Make the DEVLINK_ATTR_REGION_SNAPSHOT_ID optional and try
to allocate id automatically. Send a message back to the
caller with the snapshot info.
Example use:
$ devlink region new netdevsim/netdevsim1/dummy
netdevsim/netdevsim1/dummy: snapshot 1
$ id=$(devlink -j region new netdevsim/netdevsim1/dummy | \
jq '.[][][][]')
$ devlink region dump netdevsim/netdevsim1/dummy snapshot $id
[...]
$ devlink region del netdevsim/netdevsim1/dummy snapshot $id
v4:
- inline the notification code
v3:
- send the notification only once snapshot creation completed.
v2:
- don't wrap the line containing extack;
- add a few sentences to the docs.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll need to send snapshot info back on the socket
which requested a snapshot to be created. Factor out
constructing a snapshot description from the broadcast
notification code.
v3: new patch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QUIC servers would like to use SO_TXTIME, without having CAP_NET_ADMIN,
to efficiently pace UDP packets.
As far as sch_fq is concerned, we need to add safety checks, so
that a buggy application does not fill the qdisc with packets
having delivery time far in the future.
This patch adds a configurable horizon (default: 10 seconds),
and a configurable policy when a packet is beyond the horizon
at enqueue() time:
- either drop the packet (default policy)
- or cap its delivery time to the horizon.
$ tc -s -d qd sh dev eth0
qdisc fq 8022: root refcnt 257 limit 10000p flow_limit 100p buckets 1024
orphan_mask 1023 quantum 10Kb initial_quantum 51160b low_rate_threshold 550Kbit
refill_delay 40.0ms timer_slack 10.000us horizon 10.000s
Sent 1234215879 bytes 837099 pkt (dropped 21, overlimits 0 requeues 6)
backlog 0b 0p requeues 6
flows 1191 (inactive 1177 throttled 0)
gc 0 highprio 0 throttled 692 latency 11.480us
pkts_too_long 0 alloc_errors 0 horizon_drops 21 horizon_caps 0
v2: fixed an overflow on 32bit kernels in fq_init(), reported
by kbuild test robot <lkp@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we tell kernel to dump filters from root (ffff:ffff),
those filters on ingress (ffff:0000) are matched, but their
true parents must be dumped as they are. However, kernel
dumps just whatever we tell it, that is either ffff:ffff
or ffff:0000:
$ nl-cls-list --dev=dummy0 --parent=root
cls basic dev dummy0 id none parent root prio 49152 protocol ip match-all
cls basic dev dummy0 id :1 parent root prio 49152 protocol ip match-all
$ nl-cls-list --dev=dummy0 --parent=ffff:
cls basic dev dummy0 id none parent ffff: prio 49152 protocol ip match-all
cls basic dev dummy0 id :1 parent ffff: prio 49152 protocol ip match-all
This is confusing and misleading, more importantly this is
a regression since 4.15, so the old behavior must be restored.
And, when tc filters are installed on a tc class, the parent
should be the classid, rather than the qdisc handle. Commit
edf6711c98 ("net: sched: remove classid and q fields from tcf_proto")
removed the classid we save for filters, we can just restore
this classid in tcf_block.
Steps to reproduce this:
ip li set dev dummy0 up
tc qd add dev dummy0 ingress
tc filter add dev dummy0 parent ffff: protocol arp basic action pass
tc filter show dev dummy0 root
Before this patch:
filter protocol arp pref 49152 basic
filter protocol arp pref 49152 basic handle 0x1
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
After this patch:
filter parent ffff: protocol arp pref 49152 basic
filter parent ffff: protocol arp pref 49152 basic handle 0x1
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
Fixes: a10fa20101 ("net: sched: propagate q and parent from caller down to tcf_fill_node")
Fixes: edf6711c98 ("net: sched: remove classid and q fields from tcf_proto")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if the default qdisc setup/init fails, the device ends up with
qdisc "noop", which causes all TX packets to get dropped.
With the introduction of sysctl net/core/default_qdisc it is possible
to change the default qdisc to be more advanced, which opens for the
possibility that Qdisc_ops->init() can fail.
This patch detect these kind of failures, and choose to fallback to
qdisc "noqueue", which is so simple that its init call will not fail.
This allows the interface to continue functioning.
V2:
As this also captures memory failures, which are transient, the
device is not kept in IFF_NO_QUEUE state. This allows the net_device
to retry to default qdisc assignment.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During SMC-R link establishment the peers exchange the link_uid that
is used for debugging purposes. Save the peer link_uid in smc_link so it
can be retrieved by the smc_diag netlink interface.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link_uid of an SMC-R link is exchanged between SMC peers and its
value can be used for debugging purposes. Create a unique link_uid
during link initialization and use it in communication with SMC-R peers.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper smcr_lgr_link_deactivate_all() and eliminate duplicate code.
In smc_lgr_free(), clear the smc-r links before smc_lgr_free_bufs() is
called so buffers are already prepared for free. The usage of the soft
parameter in __smc_lgr_terminate() is no longer needed, smc_lgr_free()
can be called directly. smc_lgr_terminate_sched() and
smc_smcd_terminate() set lgr->freeing to indicate that the link group
will be freed soon to avoid unnecessary schedules of the free worker.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to set the reason code for the link group termination, and set
meaningful values before termination processing is triggered. This
reason code is sent to the peer in the final delete link message.
When the LLC request or response layer receives a message type that was
not handled, drop a warning and terminate the link group.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New connections must not be assigned to asymmetric links. Add asymmetric
link tagging using new link variable link_is_asym. The new helpers
smcr_lgr_set_type() and smcr_lgr_set_type_asym() are called to set the
state of the link group, and tag all links accordingly.
smcr_lgr_conn_assign_link() respects the link tagging and will not
assign new connections to links tagged as asymmetric link.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For new connections, assign a link from the link group, using some
simple load balancing.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add smc_llc_send_message_wait() which uses smc_wr_tx_send_wait() to send
an LLC message and waits for the message send to complete.
smc_llc_send_link_delete_all() calls the new function to send an
DELETE_LINK,ALL LLC message. The RFC states that the sender of this type
of message needs to wait for the completion event of the message
transmission and can terminate the link afterwards.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce smc_wr_tx_send_wait() to send an IB message and wait for the
tx completion event of the message. This makes sure that the message is
no longer in-flight when the function returns.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call smc_cdc_msg_validate() when a CDC message with the failover
validation bit enabled was received. Validate that the sequence number
sent with the message is one we already have received. If not, messages
were lost and the connection is terminated using a new abort_work.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a connection is switched to a new link then a link validation
message must be sent to the peer over the new link, containing the
sequence number of the last CDC message that was sent over the old link.
The peer will validate if this sequence number is the same or lower then
the number he received, and abort the connection if messages were lost.
Add smcr_cdc_msg_send_validation() to send the message validation
message and call it when a connection was switched in
smc_switch_cursor().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add smc_switch_conns() to switch all connections from a link that is
going down. Find an other link to switch the connections to, and
switch each connection to the new link. smc_switch_cursor() updates the
cursors of a connection to the state of the last successfully sent CDC
message. When there is no link to switch to, terminate the link group.
Call smc_switch_conns() when a link is going down.
And with the possibility that links of connections can switch adapt CDC
and TX functions to detect and handle link switches.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link goes down and all connections of this link need to be
switched to an other link then the producer cursor and the sequence of
the last successfully sent CDC message must be known. Add the two fields
to the SMC connection and update it in the tx completion handler.
And to allow matching of sequences in error cases reset the seqno to the
old value in smc_cdc_msg_send() when the actual send failed.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink health core conditions the reporter's recovery with the
expiration of the grace period. This is not relevant for the first
recovery. Explicitly demand that the grace period will only apply to
recoveries other than the first.
Fixes: c8e1da0bf9 ("devlink: Add health report functionality")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an application connects to the TIPC topology server and subscribes
to some services, a new connection is created along with some objects -
'tipc_subscription' to store related data correspondingly...
However, there is one omission in the connection handling that when the
connection or application is orderly shutdown (e.g. via SIGQUIT, etc.),
the connection is not closed in kernel, the 'tipc_subscription' objects
are not freed too.
This results in:
- The maximum number of subscriptions (65535) will be reached soon, new
subscriptions will be rejected;
- TIPC module cannot be removed (unless the objects are somehow forced
to release first);
The commit fixes the issue by closing the connection if the 'recvmsg()'
returns '0' i.e. when the peer is shutdown gracefully. It also includes
the other unexpected cases.
Acked-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to 1d27732f41 ("net: dsa: setup and teardown ports"), we would
not treat failures to set-up an user port as fatal, but after this
commit we would, which is a regression for some systems where interfaces
may be declared in the Device Tree, but the underlying hardware may not
be present (pluggable daughter cards for instance).
Fixes: 1d27732f41 ("net: dsa: setup and teardown ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As SMC server, when a second link was deleted, trigger the setup of an
asymmetric link. Do this by enqueueing a local ADD_LINK message which
is processed by the LLC layer as if it were received from peer. Do the
same when a new IB port became active and a new link could be created.
smc_llc_srv_add_link_local() enqueues a local ADD_LINK message.
And smc_llc_srv_delete_link_local() is used the same way to enqueue a
local DELETE_LINK message. This is used when an IB port is no longer
active.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add smc_llc_process_srv_delete_link() to process a DELETE_LINK request
as SMC server. When the request is to delete ALL links then terminate
the whole link group. If not, find the link to delete by its link_id,
send the DELETE_LINK request LLC message and wait for the response.
No matter if a response was received, clear the deleted link and update
the link group state.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add smc_llc_process_cli_delete_link() to process a DELETE_LINK request
as SMC client. When the request is to delete ALL links then terminate
the whole link group. If not, find the link to delete by its link_id,
send the DELETE_LINK response LLC message and then clear the deleted
link. Finally determine and update the link group state.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a work that is scheduled when a new DELETE_LINK LLC request is
received. The work will call either the SMC client or SMC server
DELETE_LINK processing.
And use the LLC flow framework to process incoming DELETE_LINK LLC
messages, scheduling the llc_del_link_work for those events.
With these changes smc_lgr_forget() is only called by one function and
can be migrated into smc_lgr_cleanup_early().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link group moved from asymmetric to symmetric state then the
dangling asymmetric link can be deleted. Add smc_llc_find_asym_link() to
find the respective link and add smc_llc_delete_asym_link() to delete
it.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch finalizes the ADD_LINK processing of new links. Send the
CONFIRM_LINK request to the peer, receive the response and set link
state to ACTIVE.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of SMC server new link establishment is the exchange of rkeys for
used buffers.
Loop over all used RMB buffers and send ADD_LINK_CONTINUE LLC messages
to the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of functions to process an ADD_LINK LLC request as an SMC
server. Find an alternate IB device, determine the new link group type
and get the index for the new link. Then initialize the link and send
the ADD_LINK LLC message to the peer. Save the contents of the response,
ready the link, map all used buffers and register the buffers with the
IB device. If any error occurs, stop the processing and clear the link.
And call smc_llc_srv_add_link() in af_smc.c to start second link
establishment after the initial link of a link group was created.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch finalizes the ADD_LINK processing of new links. Receive the
CONFIRM_LINK request from peer, complete the link initialization,
register all used buffers with the IB device and finally send the
CONFIRM_LINK response, which completes the ADD_LINK processing.
And activate smc_llc_cli_add_link() in af_smc.c.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of the SMC client new link establishment process is the exchange of
rkeys for all used buffers.
Add new LLC message type ADD_LINK_CONTINUE which is used to exchange
rkeys of all current RMB buffers. Add functions to iterate over all
used RMB buffers of the link group, and implement the ADD_LINK_CONTINUE
processing.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of functions to process an ADD_LINK LLC request as an SMC
client. Find an alternate IB device, determine the new link group type
and get the index for the new link. Then ready the link, map the buffers
and send an ADD_LINK LLC response. If any error occurs, send a reject
LLC message and terminate the processing.
Add smc_llc_alloc_alt_link() to find a free link index for a new link,
depending on the new link group type.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not assume the attribute has the right size.
Fixes: aea5f654e6 ("net/sched: add skbprio scheduler")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prefetch() done in fq_dequeue() can be done a bit earlier
after the refactoring of the code done in the prior patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refactors the code to not call fq_peek() from fq_dequeue_head()
since the caller can provide the skb.
Also rename fq_dequeue_head() to fq_dequeue_skb() because 'head' is
a bit vague, given the skb could come from t_root rb-tree.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fq_gc() already builds a small array of pointers, so using
kmem_cache_free_bulk() needs very little change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sizeof(struct fq_flow) is 112 bytes on 64bit arches.
This means that half of them use two cache lines, but 50% use
three cache lines.
This patch adds cache line alignment, and makes sure that only
the first cache line is touched by fq_enqueue(), which is more
expensive that fq_dequeue() in general.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A significant amount of cpu cycles is spent in fq_gc()
When fq_gc() does its lookup in the rb-tree, it needs the
following fields from struct fq_flow :
f->sk (lookup key in the rb-tree)
f->fq_node (anchor in the rb-tree)
f->next (used to determine if the flow is detached)
f->age (used to determine if the flow is candidate for gc)
This unfortunately spans two cache lines (assuming 64 bytes cache lines)
We can avoid using f->next, if we use the low order bit of f->{age|tail}
This low order bit is 0, if f->tail points to an sk_buff.
We set the low order bit to 1, if the union contains a jiffies value.
Combined with the following patch, this makes sure we only need
to bring into cpu caches one cache line per flow.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc/smc_llc.c:544:12: warning: ‘smc_llc_alloc_alt_link’ defined but not used [-Wunused-function]
static int smc_llc_alloc_alt_link(struct smc_link_group *lgr,
^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
Stable fixes
- fix handling of backchannel binding in BIND_CONN_TO_SESSION
Bugfixes
- Fix a credential use-after-free issue in pnfs_roc()
- Fix potential posix_acl refcnt leak in nfs3_set_acl
- defer slow parts of rpc_free_client() to a workqueue
- Fix an Oopsable race in __nfs_list_for_each_server()
- Fix trace point use-after-free race
- Regression: the RDMA client no longer responds to server disconnect requests
- Fix return values of xdr_stream_encode_item_{present, absent}
- _pnfs_return_layout() must always wait for layoutreturn completion
Cleanups
- Remove unreachable error conditions
-----BEGIN PGP SIGNATURE-----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=w0zk
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- fix handling of backchannel binding in BIND_CONN_TO_SESSION
Bugfixes:
- Fix a credential use-after-free issue in pnfs_roc()
- Fix potential posix_acl refcnt leak in nfs3_set_acl
- defer slow parts of rpc_free_client() to a workqueue
- Fix an Oopsable race in __nfs_list_for_each_server()
- Fix trace point use-after-free race
- Regression: the RDMA client no longer responds to server disconnect
requests
- Fix return values of xdr_stream_encode_item_{present, absent}
- _pnfs_return_layout() must always wait for layoutreturn completion
Cleanups:
- Remove unreachable error conditions"
* tag 'nfs-for-5.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix a race in __nfs_list_for_each_server()
NFSv4.1: fix handling of backchannel binding in BIND_CONN_TO_SESSION
SUNRPC: defer slow parts of rpc_free_client() to a workqueue.
NFSv4: Remove unreachable error condition due to rpc_run_task()
SUNRPC: Remove unreachable error condition
xprtrdma: Fix use of xdr_stream_encode_item_{present, absent}
xprtrdma: Fix trace point use-after-free race
xprtrdma: Restore wake-up-all to rpcrdma_cm_event_handler()
nfs: Fix potential posix_acl refcnt leak in nfs3_set_acl
NFS/pnfs: Fix a credential use-after-free issue in pnfs_roc()
NFS/pnfs: Ensure that _pnfs_return_layout() waits for layoutreturn completion
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-05-01 (v2)
The following pull-request contains BPF updates for your *net-next* tree.
We've added 61 non-merge commits during the last 6 day(s) which contain
a total of 153 files changed, 6739 insertions(+), 3367 deletions(-).
The main changes are:
1) pulled work.sysctl from vfs tree with sysctl bpf changes.
2) bpf_link observability, from Andrii.
3) BTF-defined map in map, from Andrii.
4) asan fixes for selftests, from Andrii.
5) Allow bpf_map_lookup_elem for SOCKMAP and SOCKHASH, from Jakub.
6) production cloudflare classifier as a selftes, from Lorenz.
7) bpf_ktime_get_*_ns() helper improvements, from Maciej.
8) unprivileged bpftool feature probe, from Quentin.
9) BPF_ENABLE_STATS command, from Song.
10) enable bpf_[gs]etsockopt() helpers for sock_ops progs, from Stanislav.
11) enable a bunch of common helpers for cg-device, sysctl, sockopt progs,
from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a work that is scheduled when a new ADD_LINK LLC request is
received. The work will call either the SMC client or SMC server
ADD_LINK processing.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add smc_llc_alloc_alt_link() to find a free link index for a new link,
depending on the new link group type. And update constants for the
maximum number of links to 3 (2 symmetric and 1 dangling asymmetric link).
These maximum numbers are the same as used by other implementations of the
SMC-R protocol.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new function in smc_pnet.c that searches for an alternate
IB device, using an existing link group and a primary IB device. The
alternate IB device needs to be active and must have the same PNETID
as the link group.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for multiple links makes the former DELETE LINK processing
obsolete which sent one DELETE_LINK LLC message for each single link.
Remove this processing from smc_core.c.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the introduced link down processing in all places where the link
group is terminated and take down the affected link only.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call smcr_port_err() when an IB event reports an inactive IB device.
smcr_port_err() calls smcr_link_down() for all affected links.
smcr_link_down() either triggers the local DELETE_LINK processing, or
sends an DELETE_LINK LLC message to the SMC server to initiate the
processing.
The old handler function smc_port_terminate() is removed.
Add helper smcr_link_down_cond() to take a link down conditionally, and
smcr_link_down_cond_sched() to schedule the link_down processing to a
work.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call smcr_port_add() when an IB event reports a new active IB device.
smcr_port_add() will start a work which either triggers the local
ADD_LINK processing, or send an ADD_LINK LLC message to the SMC server
to initiate the processing.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PNETID is needed to find an alternate link for a link group.
Save the PNETID of the link that is used to create the link group for
later device matching.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce llc_conf_mutex in the link group which is used to protect the
buffers and lgr states against parallel link reconfiguration.
This ensures that new connections do not start to register buffers with
the links of a link group when link creation or termination is running.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All LLC sends are done from worker context only, so remove the prep
functions which were used to build the message before it was sent, and
add the function content into the respective send function
smc_llc_send_add_link() and smc_llc_send_delete_link().
Extend smc_llc_send_add_link() to include the qp_mtu value in the LLC
message, which is needed to establish a link after the initial link was
created. Extend smc_llc_send_delete_link() to contain a link_id and a
reason code for the link deletion in the LLC message, which is needed
when a specific link should be deleted.
And add the list of existing DELETE_LINK reason codes.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce support to map and register all current buffers for a new
link. smcr_buf_map_lgr() will map used buffers for a new link and
smcr_buf_reg_lgr() can be called to register used buffers on the
IB device of the new link.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support of multiple links that are created and cleared there
is a need to unmap one link from all current buffers. Add unmapping by
link and by rmb. And make smcr_link_clear() available to be called from
the LLC layer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIRM_RKEY LLC processing handles all links in one LLC message.
Move the call to this processing out of smcr_link_reg_rmb() which does
processing per link, into smcr_lgr_reg_rmbs() which is responsible for
link group level processing. Move smcr_link_reg_rmb() into module
smc_core.c.
>From af_smc.c now call smcr_lgr_reg_rmbs() to register new rmbs on all
available links.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the gate action to the flow action entry. Add the gate parameters to
the tc_setup_flow_action() queueing to the entries of flow_action_entry
array provide to the driver.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a ingress frame gate control flow action.
Tc gate action does the work like this:
Assume there is a gate allow specified ingress frames can be passed at
specific time slot, and be dropped at specific time slot. Tc filter
chooses the ingress frames, and tc gate action would specify what slot
does these frames can be passed to device and what time slot would be
dropped.
Tc gate action would provide an entry list to tell how much time gate
keep open and how much time gate keep state close. Gate action also
assign a start time to tell when the entry list start. Then driver would
repeat the gate entry list cyclically.
For the software simulation, gate action requires the user assign a time
clock type.
Below is the setting example in user space. Tc filter a stream source ip
address is 192.168.0.20 and gate action own two time slots. One is last
200ms gate open let frame pass another is last 100ms gate close let
frames dropped. When the ingress frames have reach total frames over
8000000 bytes, the excessive frames will be dropped in that 200000000ns
time slot.
> tc qdisc add dev eth0 ingress
> tc filter add dev eth0 parent ffff: protocol ip \
flower src_ip 192.168.0.20 \
action gate index 2 clockid CLOCK_TAI \
sched-entry open 200000000 -1 8000000 \
sched-entry close 100000000 -1 -1
> tc chain del dev eth0 ingress chain 0
"sched-entry" follow the name taprio style. Gate state is
"open"/"close". Follow with period nanosecond. Then next item is internal
priority value means which ingress queue should put. "-1" means
wildcard. The last value optional specifies the maximum number of
MSDU octets that are permitted to pass the gate during the specified
time interval.
Base-time is not set will be 0 as default, as result start time would
be ((N + 1) * cycletime) which is the minimal of future time.
Below example shows filtering a stream with destination mac address is
10:00:80:00:00:00 and ip type is ICMP, follow the action gate. The gate
action would run with one close time slot which means always keep close.
The time cycle is total 200000000ns. The base-time would calculate by:
1357000000000 + (N + 1) * cycletime
When the total value is the future time, it will be the start time.
The cycletime here would be 200000000ns for this case.
> tc filter add dev eth0 parent ffff: protocol ip \
flower skip_hw ip_proto icmp dst_mac 10:00:80:00:00:00 \
action gate index 12 base-time 1357000000000 \
sched-entry close 200000000 -1 -1 \
clockid CLOCK_TAI
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current gcc-10 snapshot produces a false-positive warning:
net/core/drop_monitor.c: In function 'trace_drop_common.constprop':
cc1: error: writing 8 bytes into a region of size 0 [-Werror=stringop-overflow=]
In file included from net/core/drop_monitor.c:23:
include/uapi/linux/net_dropmon.h:36:8: note: at offset 0 to object 'entries' with size 4 declared here
36 | __u32 entries;
| ^~~~~~~
I reported this in the gcc bugzilla, but in case it does not get
fixed in the release, work around it by using a temporary variable.
Fixes: 9a8afc8d39 ("Network Drop Monitor: Adding drop monitor implementation & Netlink protocol")
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=94881
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d5b90e99e1 ("devlink: report 0 after hitting end in region read")
fixed region dump, but region read still returns a spurious error:
$ devlink region read netdevsim/netdevsim1/dummy snapshot 0 addr 0 len 128
0000000000000000 a6 f4 c4 1c 21 35 95 a6 9d 34 c3 5b 87 5b 35 79
0000000000000010 f3 a0 d7 ee 4f 2f 82 7f c6 dd c4 f6 a5 c3 1b ae
0000000000000020 a4 fd c8 62 07 59 48 03 70 3b c7 09 86 88 7f 68
0000000000000030 6f 45 5d 6d 7d 0e 16 38 a9 d0 7a 4b 1e 1e 2e a6
0000000000000040 e6 1d ae 06 d6 18 00 85 ca 62 e8 7e 11 7e f6 0f
0000000000000050 79 7e f7 0f f3 94 68 bd e6 40 22 85 b6 be 6f b1
0000000000000060 af db ef 5e 34 f0 98 4b 62 9a e3 1b 8b 93 fc 17
devlink answers: Invalid argument
0000000000000070 61 e8 11 11 66 10 a5 f7 b1 ea 8d 40 60 53 ed 12
This is a minimal fix, I'll follow up with a restructuring
so we don't have two checks for the same condition.
Fixes: fdd41ec21e ("devlink: Return right error code in case of errors for region read")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In skb_panic() the real pointer values are really needed to diagnose
issues, e.g. data and head are related (to calculate headroom). The
hashed versions of the addresses doesn't make much sense here. The
patch use the printk specifier %px to print the actual address.
The printk documentation on %px:
https://www.kernel.org/doc/html/latest/core-api/printk-formats.html#unmodified-addresses
Fixes: ad67b74d24 ("printk: hash addresses printed with %p")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the behavior of TCP_LINGER2 about its limit. The
sysctl_tcp_fin_timeout used to be the limit of TCP_LINGER2 but now it's
only the default value. A new macro named TCP_FIN_TIMEOUT_MAX is added
as the limit of TCP_LINGER2, which is 2 minutes.
Since TCP_LINGER2 used sysctl_tcp_fin_timeout as the default value
and the limit in the past, the system administrator cannot set the
default value for most of sockets and let some sockets have a greater
timeout. It might be a mistake that let the sysctl to be the limit of
the TCP_LINGER2. Maybe we can add a new sysctl to set the max of
TCP_LINGER2, but FIN-WAIT-2 timeout is usually no need to be too long
and 2 minutes are legal considering TCP specs.
Changes in v3:
- Remove the new socket option and change the TCP_LINGER2 behavior so
that the timeout can be set to value between sysctl_tcp_fin_timeout
and 2 minutes.
Changes in v2:
- Add int overflow check for the new socket option.
Changes in v1:
- Add a new socket option to set timeout greater than
sysctl_tcp_fin_timeout.
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nik reported a bug with pcpu dst cache when nexthop objects are
used illustrated by the following:
$ ip netns add foo
$ ip -netns foo li set lo up
$ ip -netns foo addr add 2001:db8:11::1/128 dev lo
$ ip netns exec foo sysctl net.ipv6.conf.all.forwarding=1
$ ip li add veth1 type veth peer name veth2
$ ip li set veth1 up
$ ip addr add 2001:db8:10::1/64 dev veth1
$ ip li set dev veth2 netns foo
$ ip -netns foo li set veth2 up
$ ip -netns foo addr add 2001:db8:10::2/64 dev veth2
$ ip -6 nexthop add id 100 via 2001:db8:10::2 dev veth1
$ ip -6 route add 2001:db8:11::1/128 nhid 100
Create a pcpu entry on cpu 0:
$ taskset -a -c 0 ip -6 route get 2001:db8:11::1
Re-add the route entry:
$ ip -6 ro del 2001:db8:11::1
$ ip -6 route add 2001:db8:11::1/128 nhid 100
Route get on cpu 0 returns the stale pcpu:
$ taskset -a -c 0 ip -6 route get 2001:db8:11::1
RTNETLINK answers: Network is unreachable
While cpu 1 works:
$ taskset -a -c 1 ip -6 route get 2001:db8:11::1
2001:db8:11::1 from :: via 2001:db8:10::2 dev veth1 src 2001:db8:10::1 metric 1024 pref medium
Conversion of FIB entries to work with external nexthop objects
missed an important difference between IPv4 and IPv6 - how dst
entries are invalidated when the FIB changes. IPv4 has a per-network
namespace generation id (rt_genid) that is bumped on changes to the FIB.
Checking if a dst_entry is still valid means comparing rt_genid in the
rtable to the current value of rt_genid for the namespace.
IPv6 also has a per network namespace counter, fib6_sernum, but the
count is saved per fib6_node. With the per-node counter only dst_entries
based on fib entries under the node are invalidated when changes are
made to the routes - limiting the scope of invalidations. IPv6 uses a
reference in the rt6_info, 'from', to track the corresponding fib entry
used to create the dst_entry. When validating a dst_entry, the 'from'
is used to backtrack to the fib6_node and check the sernum of it to the
cookie passed to the dst_check operation.
With the inline format (nexthop definition inline with the fib6_info),
dst_entries cached in the fib6_nh have a 1:1 correlation between fib
entries, nexthop data and dst_entries. With external nexthops, IPv6
looks more like IPv4 which means multiple fib entries across disparate
fib6_nodes can all reference the same fib6_nh. That means validation
of dst_entries based on external nexthops needs to use the IPv4 format
- the per-network namespace counter.
Add sernum to rt6_info and set it when creating a pcpu dst entry. Update
rt6_get_cookie to return sernum if it is set and update dst_check for
IPv6 to look for sernum set and based the check on it if so. Finally,
rt6_get_pcpu_route needs to validate the cached entry before returning
a pcpu entry (similar to the rt_cache_valid calls in __mkroute_input and
__mkroute_output for IPv4).
This problem only affects routes using the new, external nexthops.
Thanks to the kbuild test robot for catching the IS_ENABLED needed
around rt_genid_ipv6 before I sent this out.
Fixes: 5b98324ebe ("ipv6: Allow routes to use nexthop objects")
Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bpf_getsockopt and bpf_setsockopt helpers operate on the
'struct bpf_sock_ops' context in BPF_PROG_TYPE_SOCK_OPS program.
Let's generalize them and make them available for 'struct bpf_sock_addr'.
That way, in the future, we can allow those helpers in more places.
As an example, let's expose those 'struct bpf_sock_addr' based helpers to
BPF_CGROUP_INET{4,6}_CONNECT hooks. That way we can override CC before the
connection is made.
v3:
* Expose custom helpers for bpf_sock_addr context instead of doing
generic bpf_sock argument (as suggested by Daniel). Even with
try_socket_lock that doesn't sleep we have a problem where context sk
is already locked and socket lock is non-nestable.
v2:
* s/BPF_PROG_TYPE_CGROUP_SOCKOPT/BPF_PROG_TYPE_SOCK_OPS/
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200430233152.199403-1-sdf@google.com
Not much to be done here:
- add SPDX header;
- add a document title;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not much to be done here:
- add SPDX header;
- adjust title markup;
- remove a tail whitespace;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new ndo to get the xmit slave of master device. The reference
counters are not incremented so the caller must be careful with locks.
User can ask to get the xmit slave assume all the slaves can
transmit by set all_slaves arg to true.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Do not update the UDP checksum when it's zero, from Guillaume Nault.
2) Fix return of local variable in nf_osf, from Arnd Bergmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add, and use in generic netlink, helpers to dump out a netlink
policy to userspace, including all the range validation data,
nested policies etc.
This lets userspace discover what the kernel understands.
For families/commands other than generic netlink, the helpers
need to be used directly in an appropriate command, or we can
add some infrastructure (a new netlink family) that those can
register their policies with for introspection. I'm not that
familiar with non-generic netlink, so that's left out for now.
The data exposed to userspace also includes min and max length
for binary/string data, I've done that instead of letting the
userspace tools figure out whether min/max is intended based
on the type so that we can extend this later in the kernel, we
might want to just use the range data for example.
Because of this, I opted to not directly expose the NLA_*
values, even if some of them are already exposed via BPF, as
with min/max length we don't need to have different types here
for NLA_BINARY/NLA_MIN_LEN/NLA_EXACT_LEN, we just make them
all NL_ATTR_TYPE_BINARY with min/max length optionally set.
Similarly, we don't really need NLA_MSECS, and perhaps can
remove it in the future - but not if we encode it into the
userspace API now. It gets mapped to NL_ATTR_TYPE_U64 here.
Note that the exposing here corresponds to the strict policy
interpretation, and NLA_UNSPEC items are omitted entirely.
To get those, change them to NLA_MIN_LEN which behaves in
exactly the same way, but is exposed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a validation type instead, so we can later expose
the NLA_* values to userspace for policy descriptions.
Some transformations were done with this spatch:
@@
identifier p;
expression X, L, A;
@@
struct nla_policy p[X] = {
[A] =
-{ .type = NLA_EXACT_LEN_WARN, .len = L },
+NLA_POLICY_EXACT_LEN_WARN(L),
...
};
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have limited recursive policy validation to avoid
stack overflows, change nl80211 to actually link the nested
policy (linking back to itself eventually), which allows some
code cleanups.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the netlink policy, we currently have a void *validation_data
that's pointing to different things:
* a u32 value for bitfield32,
* the netlink policy for nested/nested array
* the string for NLA_REJECT
Remove the pointer and place appropriate type-safe items in the
union instead.
While at it, completely dissolve the pointer for the bitfield32
case and just put the value there directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space can request to delete a range of VLANs from a bridge slave in
one netlink request. For each deleted VLAN the FDB needs to be traversed
in order to flush all the affected entries.
If a large range of VLANs is deleted and the number of FDB entries is
large or the FDB lock is contented, it is possible for the kernel to
loop through the deleted VLANs for a long time. In case preemption is
disabled, this can result in a soft lockup.
Fix this by adding a schedule point after each VLAN is deleted to yield
the CPU, if needed. This is safe because the VLANs are traversed in
process context.
Fixes: bdced7ef78 ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Tested-by: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When all hsr slave interfaces are removed, hsr interface doesn't work.
At that moment, it's fine to remove an unused hsr interface automatically
for saving resources.
That's a common behavior of virtual interfaces.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sysctl to control hrtimer slack, default of 100 usec.
This gives the opportunity to reduce system overhead,
and help very short RTT flows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tcp_sack_new_ofo_skb() sends an ack if prior
acks were 'compressed', if room has to be made in tp->selective_acks[]
But there is no guarantee all four sack ranges can be included
in SACK option. As a matter of fact, when TCP timestamps option
is used, only three SACK ranges can be included.
Lets assume only two ranges can be included, and force the ack:
- When we touch more than 2 ranges in the reordering
done if tcp_sack_extend() could be done.
- If we have at least 2 ranges when adding a new one.
This enforces that before a range is in third or fourth
position, at least one ACK packet included it in first/second
position.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 86de5921a3 ("tcp: defer SACK compression after DupThresh")
I added a TCP_FASTRETRANS_THRESH bias to tp->compressed_ack in order
to enable sack compression only after 3 dupacks.
Since we plan to relax this rule for flows that involve
stacks not requiring this old rule, this patch adds
a distinct tp->dup_ack_counter.
This means the TCP_FASTRETRANS_THRESH value is now used
in a single location that a future patch can adjust:
if (tp->dup_ack_counter < TCP_FASTRETRANS_THRESH) {
tp->dup_ack_counter++;
goto send_now;
}
This patch also introduces tcp_sack_compress_send_ack()
helper to ease following patch comprehension.
This patch refines LINUX_MIB_TCPACKCOMPRESSED to not
count the acks that we had to send if the timer expires
or tcp_sack_compress_send_ack() is sending an ack.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- use autonumbered list markups;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- use bold markups on a few places;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ability to filter sockets based on cgroup v2 ID.
Such filter is helpful in ss utility for filtering sockets by
cgroup pathname.
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds cgroup v2 ID to common inet diag message attributes.
Cgroup v2 ID is kernfs ID (ino or ino+gen). This attribute allows filter
inet diag output by cgroup ID obtained by name_to_handle_at() syscall.
When net_cls or net_prio cgroup is activated this ID is equal to 1 (root
cgroup ID) for newly created sockets.
Some notes about this ID:
1) gets initialized in socket() syscall
2) incoming socket gets ID from listening socket
(not during accept() syscall)
3) not changed when process get moved to another cgroup
4) can point to deleted cgroup (refcounting)
v2:
- use CONFIG_SOCK_CGROUP_DATA instead if CONFIG_CGROUPS
v3:
- fix attr size by using nla_total_size_64bit() (Eric Dumazet)
- more detailed commit message (Konstantin Khlebnikov)
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-By: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The connection layer in af_smc.c is now using the new LLC flow
framework, which made the link state DELETING obsolete. Remove the state
and the respective helpers.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new SMC-R multiple link support will support a maximum of 3 links,
and one CONFIRM_RKEY LLC message can transport 3 rkeys of an rmb buffer.
There is no need for the LLC message type CONFIRM_RKEY_CONTINUE which is
needed when more than 3 rkeys per rmb buffer needs to be exchanged.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the LLC flow framework for the processing of DELETE_RKEY messages
that were received from the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the LLC flow framework for the processing of CONFIRM_RKEY messages
that were received from the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce smc_rtoken_set() to set the rtoken for a new link to an
existing rmb whose rtoken is given, and smc_rtoken_set2() to set an
rtoken for a new link whose link_id is given.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the extra function and move the two-liner for the TEST_LINK
response processing into the event handler function.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt smc_llc_do_delete_rkey() to use the LLC flow and support multiple
links when deleting the rkeys for rmb buffers at the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt smc_llc_do_confirm_rkey() to use the LLC flow and support the
rkeys of multiple links when the CONFIRM_RKEY LLC message is build.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the code that processes the SMC client part of connection
establishment to use the LLC flow framework (CONFIRM_LINK request
messages).
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the code that processes the SMC server part of connection
establishment to use the LLC flow framework (CONFIRM_LINK response
messages).
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce smc_llc_eval_conf_link() to evaluate the CONFIRM_LINK message
contents. This implements this logic at the LLC layer. The function will
be used by af_smc.c to process the received LLC layer messages.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a type field to the link group which reflects the current link group
redundancy state.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce smc_llc_enqueue() to enqueue LLC messages, and adapt
smc_llc_rx_handler() to enqueue all received LLC messages.
smc_llc_enqueue() also makes it possible to enqueue LLC messages from
local code.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new framework allows to start specific types of LLC control flows,
protects active flows and makes it possible to wait for flows to finish
before starting a new flow.
This mechanism is used for the LLC control layer to model flows like
'add link' or 'delete link' which need to send/receive several LLC
messages and are not allowed to get interrupted by the wrong type of
messages.
'Add link' or 'Delete link' messages arriving in the middle of a flow
are delayed and processed when the current flow finished.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_v{4,6}_syn_recv_sock() set 'own_req' only when returning
a not NULL 'child', let's check 'own_req' only if child is
available to avoid an - unharmful - UBSAN splat.
v1 -> v2:
- reference the correct hash
Fixes: 4c8941de78 ("mptcp: avoid flipping mp_capable field in syn_recv_sock()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing MPC+data packets we set the dss field, so
we must also initialize the data_fin, or we can find stray
value there.
Fixes: 9a19371bf0 ("mptcp: fix data_fin handing in RX path")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mentioned RX option field is initialized only for DSS
packet, we must access it only if 'dss' is set too, or
the subflow will end-up in a bad status, leading to
RFC violations.
Fixes: d22f4988ff ("mptcp: process MP_CAPABLE data option")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzcaller has found a way to trigger the WARN_ON_ONCE condition
in check_fully_established().
The root cause is a legit fallback to TCP scenario, so replace
the WARN with a plain message on a more strict condition.
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the MPTCP code uses 2 hooks to process syn-ack
packets, mptcp_rcv_synsent() and the sk_rx_dst_set()
callback.
We can drop the first, moving the relevant code into the
latter, reducing the hooking into the TCP code. This is
also needed by the next patch.
v1 -> v2:
- use local tcp sock ptr instead of casting the sk variable
several times - DaveM
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
White-list map lookup for SOCKMAP/SOCKHASH from BPF. Lookup returns a
pointer to a full socket and acquires a reference if necessary.
To support it we need to extend the verifier to know that:
(1) register storing the lookup result holds a pointer to socket, if
lookup was done on SOCKMAP/SOCKHASH, and that
(2) map lookup on SOCKMAP/SOCKHASH is a reference acquiring operation,
which needs a corresponding reference release with bpf_sk_release.
On sock_map side, lookup handlers exposed via bpf_map_ops now bump
sk_refcnt if socket is reference counted. In turn, bpf_sk_select_reuseport,
the only in-kernel user of SOCKMAP/SOCKHASH ops->map_lookup_elem, was
updated to release the reference.
Sockets fetched from a map can be used in the same way as ones returned by
BPF socket lookup helpers, such as bpf_sk_lookup_tcp. In particular, they
can be used with bpf_sk_assign to direct packets toward a socket on TC
ingress path.
Suggested-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200429181154.479310-2-jakub@cloudflare.com
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for nf-next:
1) Add IPS_HW_OFFLOAD status bit, from Bodong Wang.
2) Remove 128-bit limit on the set element data area, rise it
to 64 bytes.
3) Report EOPNOTSUPP for unsupported NAT types and flags.
4) Set up nft_nat flags from the control plane path.
5) Add helper functions to set up the nf_nat_range2 structure.
6) Add netmap support for nft_nat.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo points out that mptcp_disconnect is bogus:
"lock_sock(sk);
looks suspicious (lock should be already held by the caller)
And call to: tcp_disconnect(sk, flags); too, sk is not a tcp
socket".
->disconnect() gets called from e.g. inet_stream_connect when
one tries to disassociate a connected socket again (to re-connect
without closing the socket first).
MPTCP however uses mptcp_stream_connect, not inet_stream_connect,
for the mptcp-socket connect call.
inet_stream_connect only gets called indirectly, for the tcp socket,
so any ->disconnect() calls end up calling tcp_disconnect for that
tcp subflow sk.
This also explains why syzkaller has not yet reported a problem
here. So for now replace this with a stub that doesn't do anything.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/14
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce smc_llc_lgr_init() and smc_llc_lgr_clear() to implement all
llc layer specific initialization and cleanup in module smc_llc.c.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The locks for sndbufs and rmbs are never used from atomic context. Using
a mutex for these locks will allow to nest locks with other mutexes.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When llc responses are received then possible waiters for this response
are to be notified. This can be done in tasklet context, without to
use a work in the llc work queue. Move all code that handles llc
responses into smc_llc_rx_response().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming llc messages are processed in irq tasklet context, and
a worker is used to send outgoing messages. The worker is needed
because getting a send buffer could result in a wait for a free buffer.
To make sure all incoming llc messages are processed in a serialized way
introduce an event queue and create a new queue entry for each message
which is queued to this event queue. A new worker processes the event
queue entries in order.
And remove the use of a separate worker to send outgoing llc messages
because the messages are processed in worker context already.
With this event queue the serialized llc_wq work queue is obsolete,
remove it.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cancel the testlink worker during link clear processing and remove the
extra function smc_llc_link_inactive().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The testlink work waits for a response to the testlink request and
blocks the single threaded llc_wq. This type of work does not have to be
serialized and can be moved to the system work queue.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before a link can be reused it must have been cleared. Lowest current
link state is INACTIVE, which does not mean that the link is already
cleared.
Add a new state UNUSED that is set when the link is cleared and can be
reused.
Add helper smc_llc_usable_link() to find an active link in a link group,
and smc_link_usable() to determine if a link is usable.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend smc_rmb_rtoken_handling() and smc_rtoken_delete() to support
multiple links.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for the support of multiple links remove the usage of
a static link id (SMC_SINGLE_LINK) and allow dynamic link ids.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for the support of multiple links remove the usage of
a static link id (SMC_SINGLE_LINK) and allow dynamic link ids.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link_id is the index of the link in the array of the link group.
When a link in the array is reused for a new link, a different unique
link_id should be used, otherwise the index in the array could collide
with the previous link at this array position.
Use a new variable link_idx as array index, and make link_id an
increasing unique id value.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the initialization of a new link into its own function, separate
from smc_lgr_create, to allow more than one link per link group.
Do an extra check if the IB device initialization was successful, and
reset the link state if any error occurs during smcr_link_init().
And rename two existing functions to use the prefix smcr_ to indicate
that they belong to the SMC-R code path.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pnet table stored pnet ids in the smc device structures. When a
device is going down its smc device structure is freed, and when the
device is brought online again it no longer has a pnet id set.
Rework the pnet table implementation to store the device name with their
assigned pnet id and apply the pnet id to devices when they are
registered.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-10 points out that a code path exists where a pointer to a stack
variable may be passed back to the caller:
net/netfilter/nfnetlink_osf.c: In function 'nf_osf_hdr_ctx_init':
cc1: warning: function may return address of local variable [-Wreturn-local-addr]
net/netfilter/nfnetlink_osf.c:171:16: note: declared here
171 | struct tcphdr _tcph;
| ^~~~~
I am not sure whether this can happen in practice, but moving the
variable declaration into the callers avoids the problem.
Fixes: 31a9c29210 ("netfilter: nf_osf: add struct nf_osf_hdr_ctx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There's no callers in-tree anymore since commit 84287bb328 ("ila: add
checksum neutral map auto").
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now HE operation element in bss_conf includes variable length
optional field followed by other HE variable. Though the optional
field never be used, actually it is referring to next member of the
bss_conf structure which is not correct. Fix it by declaring needed
HE operation fields within bss_conf itself.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1587768108-25248-2-git-send-email-rmanohar@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the Beacon frame specific legacy rate configuration, if specified
for AP or mesh, instead of the generic rate mask when selecting the TX
rate for Beacon frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200425155713.25687-4-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not much to be done here:
- add SPDX header;
- add a document title;
- mark a literal as such, in order to avoid a warning;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- mark lists as such;
- mark tables as such;
- use footnote markup;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- mark code blocks and literals as such;
- mark tables as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark lists as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't much to be done here. Just:
- add SPDX header;
- add a document title.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't much to be done here. Just:
- add SPDX header;
- add a document title.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bugfixes:
- Restore wake-up-all to rpcrdma_cm_event_handler()
- Otherwise the client won't respond to server disconnect requests
- Fix tracepoint use-after-free race
- Fix usage of xdr_stream_encode_item_{present, absent}
- These functions return a size on success, and not 0
-----BEGIN PGP SIGNATURE-----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=jre3
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-for-5.7-2' of git://git.linux-nfs.org/projects/anna/linux-nfs
NFSoRDMA Client Fixes for Linux 5.7
Bugfixes:
- Restore wake-up-all to rpcrdma_cm_event_handler()
- Otherwise the client won't respond to server disconnect requests
- Fix tracepoint use-after-free race
- Fix usage of xdr_stream_encode_item_{present, absent}
- These functions return a size on success, and not 0
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
The rpciod workqueue is on the write-out path for freeing dirty memory,
so it is important that it never block waiting for memory to be
allocated - this can lead to a deadlock.
rpc_execute() - which is often called by an rpciod work item - calls
rcp_task_release_client() which can lead to rpc_free_client().
rpc_free_client() makes two calls which could potentially block wating
for memory allocation.
rpc_clnt_debugfs_unregister() calls into debugfs and will block while
any of the debugfs files are being accessed. In particular it can block
while any of the 'open' methods are being called and all of these use
malloc for one thing or another. So this can deadlock if the memory
allocation waits for NFS to complete some writes via rpciod.
rpc_clnt_remove_pipedir() can take the inode_lock() and while it isn't
obvious that memory allocations can happen while the lock it held, it is
safer to assume they might and to not let rpciod call
rpc_clnt_remove_pipedir().
So this patch moves these two calls (together with the final kfree() and
rpciod_down()) into a work-item to be run from the system work-queue.
rpciod can continue its important work, and the final stages of the free
can happen whenever they happen.
I have seen this deadlock on a 4.12 based kernel where debugfs used
synchronize_srcu() when removing objects. synchronize_srcu() requires a
workqueue and there were no free workther threads and none could be
allocated. While debugsfs no longer uses SRCU, I believe the deadlock
is still possible.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Current route nexthop API maintains user space compatibility
with old route API by default. Dumps and netlink notifications
support both new and old API format. In systems which have
moved to the new API, this compatibility mode cancels some
of the performance benefits provided by the new nexthop API.
This patch adds new sysctl nexthop_compat_mode which is on
by default but provides the ability to turn off compatibility
mode allowing systems to run entirely with the new routing
API. Old route API behaviour and support is not modified by this
sysctl.
Uses a single sysctl to cover both ipv4 and ipv6 following
other sysctls. Covers dumps and delete notifications as
suggested by David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used in subsequent work to skip route delete
notifications on nexthop deletes.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in Christoph Hellwig's series that changes the sysctl's ->proc_handler
methods to take kernel pointers instead. It gets rid of the set_fs address
space overrides used by BPF. As per discussion, pull in the feature branch
into bpf-next as it relates to BPF sysctl progs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200427071508.GV23230@ZenIV.linux.org.uk/T/
This change allows scatternet connections to be created if the
controller reports support and the HCI_QUIRK_VALID_LE_STATES indicates
that the reported LE states can be trusted.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch allows you to NAT the network address prefix onto another
network address prefix, a.k.a. netmapping.
Userspace must specify the NF_NAT_RANGE_NETMAP flag and the prefix
address through the NFTA_NAT_REG_ADDR_MIN and NFTA_NAT_REG_ADDR_MAX
netlink attributes.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of EINVAL which should be used for malformed netlink messages.
Fixes: eb31628e37 ("netfilter: nf_tables: Add support for IPv6 NAT")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
tcp_bpf_recvmsg() invokes sk_psock_get(), which returns a reference of
the specified sk_psock object to "psock" with increased refcnt.
When tcp_bpf_recvmsg() returns, local variable "psock" becomes invalid,
so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in several exception handling paths
of tcp_bpf_recvmsg(). When those error scenarios occur such as "flags"
includes MSG_ERRQUEUE, the function forgets to decrease the refcnt
increased by sk_psock_get(), causing a refcnt leak.
Fix this issue by calling sk_psock_put() or pulling up the error queue
read handling when those error scenarios occur.
Fixes: e7a5f1f1cd ("bpf/sockmap: Read psock ingress_msg before sk_receive_queue")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/1587872115-42805-1-git-send-email-xiyuyang19@fudan.edu.cn
- bump version strings, by Simon Wunderlich
- fix spelling error, by Sven Eckelmann
- drop unneeded types.h include, by Sven Eckelmann
- change random number generation to prandom_u32_max(),
by Sven Eckelmann
- remove unused function batadv_arp_change_timeout(), by Yue Haibing
-----BEGIN PGP SIGNATURE-----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=5bKt
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20200427' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- fix spelling error, by Sven Eckelmann
- drop unneeded types.h include, by Sven Eckelmann
- change random number generation to prandom_u32_max(),
by Sven Eckelmann
- remove unused function batadv_arp_change_timeout(), by Yue Haibing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix random number generation in network coding, by George Spelvin
- fix reference counter leaks, by Xiyu Yang (3 patches)
-----BEGIN PGP SIGNATURE-----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=fNPb
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20200427' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- fix random number generation in network coding, by George Spelvin
- fix reference counter leaks, by Xiyu Yang (3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot managed to set up sfq so that q->scaled_quantum was zero,
triggering an infinite loop in sfq_dequeue()
More generally, we must only accept quantum between 1 and 2^18 - 7,
meaning scaled_quantum must be in [1, 0x7FFF] range.
Otherwise, we also could have a loop in sfq_dequeue()
if scaled_quantum happens to be 0x8000, since slot->allot
could indefinitely switch between 0 and 0x8000.
Fixes: eeaeb068f1 ("sch_sfq: allow big packets and be fair")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+0251e883fe39e7a0cb0a@syzkaller.appspotmail.com
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not possible to have the MRP and STP running at the same time on the
bridge, therefore add check when enabling the STP to check if MRP is already
enabled. In that case return error.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To integrate MRP into the bridge, the bridge needs to do the following:
- detect if the MRP frame was received on MRP ring port in that case it would be
processed otherwise just forward it as usual.
- enable parsing of MRP
- before whenever the bridge was set up, it would set all the ports in
forwarding state. Add an extra check to not set ports in forwarding state if
the port is an MRP ring port. The reason of this change is that if the MRP
instance initially sets the port in blocked state by setting the bridge up it
would overwrite this setting.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement netlink interface to configure MRP. The implementation
will do sanity checks over the attributes and then eventually call the MRP
interface.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the MRP API.
In case the HW can't generate MRP Test frames then the SW will try to generate
the frames. In case that also the SW will fail in generating the frames then a
error is return to the userspace. The userspace is responsible to generate all
the other MRP frames regardless if the test frames are generated by HW or SW.
The forwarding/termination of MRP frames is happening in the kernel and is done
by the MRP instance. The userspace application doesn't do the forwarding.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the MRP api for switchdev.
These functions will just eventually call the switchdev functions:
switchdev_port_obj_add/del and switchdev_port_attr_set.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the MRP interface.
This interface is used by the netlink to update the MRP instances and by the MRP
to make the calls to switchdev to offload it to HW.
It defines an MRP instance 'struct br_mrp' which is a list of MRP instances.
Which will be part of the 'struct net_bridge'. Each instance has 2 ring ports,
a bridge and an ID.
In case the HW can't generate MRP Test frames then the SW will generate those.
br_mrp_add - adds a new MRP instance.
br_mrp_del - deletes an existing MRP instance. Each instance has an ID(ring_id).
br_mrp_set_port_state - changes the port state. The port can be in forwarding
state, which means that the frames can pass through or in blocked state which
means that the frames can't pass through except MRP frames. This will
eventually call the switchdev API to notify the HW. This information is used
also by the SW bridge to know how to forward frames in case the HW doesn't
have this capability.
br_mrp_set_port_role - a port role can be primary or secondary. This
information is required to be pushed to HW in case the HW can generate
MRP_Test frames. Because the MRP_Test frames contains a file with this
information. Otherwise the HW will not be able to generate the frames
correctly.
br_mrp_set_ring_state - a ring can be in state open or closed. State open means
that the mrp port stopped receiving MRP_Test frames, while closed means that
the mrp port received MRP_Test frames. Similar with br_mrp_port_role, this
information is pushed in HW because the MRP_Test frames contain this
information.
br_mrp_set_ring_role - a ring can have the following roles MRM or MRC. For the
role MRM it is expected that the HW can terminate the MRP frames, notify the
SW that it stopped receiving MRP_Test frames and trapp all the other MRP
frames. While for MRC mode it is expected that the HW can forward the MRP
frames only between the MRP ports and copy MRP_Topology frames to CPU. In
case the HW doesn't support a role it needs to return an error code different
than -EOPNOTSUPP.
br_mrp_start_test - this starts/stops the generation of MRP_Test frames. To stop
the generation of frames the interval needs to have a value of 0. In this case
the userspace needs to know if the HW supports this or not. Not to have
duplicate frames(generated by HW and SW). Because if the HW supports this then
the SW will not generate anymore frames and will expect that the HW will
notify when it stopped receiving MRP frames using the function
br_mrp_port_open.
br_mrp_port_open - this function is used by drivers to notify the userspace via
a netlink callback that one of the ports stopped receiving MRP_Test frames.
This function is called only when the node has the role MRM. It is not
supposed to be called from userspace.
br_mrp_port_switchdev_add - this corresponds to the function br_mrp_add,
and will notify the HW that a MRP instance is added. The function gets
as parameter the MRP instance.
br_mrp_port_switchdev_del - this corresponds to the function br_mrp_del,
and will notify the HW that a MRP instance is removed. The function
gets as parameter the ID of the MRP instance that is removed.
br_mrp_port_switchdev_set_state - this corresponds to the function
br_mrp_set_port_state. It would notify the HW if it should block or not
non-MRP frames.
br_mrp_port_switchdev_set_port - this corresponds to the function
br_mrp_set_port_role. It would set the port role, primary or secondary.
br_mrp_switchdev_set_role - this corresponds to the function
br_mrp_set_ring_role and would set one of the role MRM or MRC.
br_mrp_switchdev_set_ring_state - this corresponds to the function
br_mrp_set_ring_state and would set the ring to be open or closed.
br_mrp_switchdev_send_ring_test - this corresponds to the function
br_mrp_start_test. This will notify the HW to start or stop generating
MRP_Test frames. Value 0 for the interval parameter means to stop generating
the frames.
br_mrp_port_open - this function is used to notify the userspace that the port
lost the continuity of MRP Test frames.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new port attribute, IFLA_BRPORT_MRP_RING_OPEN, which allows
to notify the userspace when the port lost the continuite of MRP frames.
This attribute is set by kernel whenever the SW or HW detects that the ring is
being open or closed.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To integrate MRP into the bridge, first the bridge needs to be aware of ports
that are part of an MRP ring and which rings are on the bridge.
Therefore extend bridge interface with the following:
- add new flag(BR_MPP_AWARE) to the net bridge ports, this bit will be
set when the port is added to an MRP instance. In this way it knows if
the frame was received on MRP ring port
- add new flag(BR_MRP_LOST_CONT) to the net bridge ports, this bit will be set
when the port lost the continuity of MRP Test frames.
- add a list of MRP instances
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the option BRIDGE_MRP to allow to build in or not MRP support.
The default value is N.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My intent was to not let users set a zero drop_batch_size,
it seems I once again messed with min()/max().
Fixes: 9d18562a22 ("fq_codel: add batch ability to fq_codel_drop()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tls_data_ready() invokes sk_psock_get(), which returns a reference of
the specified sk_psock object to "psock" with increased refcnt.
When tls_data_ready() returns, local variable "psock" becomes invalid,
so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
tls_data_ready(). When "psock->ingress_msg" is empty but "psock" is not
NULL, the function forgets to decrease the refcnt increased by
sk_psock_get(), causing a refcnt leak.
Fix this issue by calling sk_psock_put() on all paths when "psock" is
not NULL.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
x25_connect() invokes x25_get_neigh(), which returns a reference of the
specified x25_neigh object to "x25->neighbour" with increased refcnt.
When x25 connect success and returns, the reference still be hold by
"x25->neighbour", so the refcount should be decreased in
x25_disconnect() to keep refcount balanced.
The reference counting issue happens in x25_disconnect(), which forgets
to decrease the refcnt increased by x25_get_neigh() in x25_connect(),
causing a refcnt leak.
Fix this issue by calling x25_neigh_put() before x25_disconnect()
returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_exec_tx_verdict() invokes sk_psock_get(), which returns a reference
of the specified sk_psock object to "psock" with increased refcnt.
When bpf_exec_tx_verdict() returns, local variable "psock" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
bpf_exec_tx_verdict(). When "policy" equals to NULL but "psock" is not
NULL, the function forgets to decrease the refcnt increased by
sk_psock_get(), causing a refcnt leak.
Fix this issue by calling sk_psock_put() on this error path before
bpf_exec_tx_verdict() returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable err is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In virtio_transport.c, if the virtqueue is full, the transmitting
packet is queued up and it will be sent in the next iteration.
This causes the same packet to be delivered multiple times to
monitoring devices.
We want to continue to deliver packets to monitoring devices before
it is put in the virtqueue, to avoid that replies can appear in the
packet capture before the transmitted packet.
This patch fixes the issue, adding a new flag (tap_delivered) in
struct virtio_vsock_pkt, to check if the packet is already delivered
to monitoring devices.
In vhost/vsock.c, we are splitting packets, so we must set
'tap_delivered' to false when we queue up the same virtio_vsock_pkt
to handle the remaining bytes.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've noticed that when krb5i or krb5p security is in use,
retransmitted requests are missing the server's duplicate reply
cache. The computed checksum on the retransmitted request does not
match the cached checksum, resulting in the server performing the
retransmitted request again instead of returning the cached reply.
The assumptions made when removing xdr_buf_trim() were not correct.
In the send paths, the upper layer has already set the segment
lengths correctly, and shorting the buffer's content is simply a
matter of reducing buf->len.
xdr_buf_trim() is the right answer in the receive/unwrap path on
both the client and the server. The buffer segment lengths have to
be shortened one-by-one.
On the server side in particular, head.iov_len needs to be updated
correctly to enable nfsd_cache_csum() to work correctly. The simple
buf->len computation doesn't do that, and that results in
checksumming stale data in the buffer.
The problem isn't noticed until there's significant instability of
the RPC transport. At that point, the reliability of retransmit
detection on the server becomes crucial.
Fixes: 241b1f419f ("SUNRPC: Remove xdr_buf_trim()")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
When the au_ralign field was added to gss_unwrap_resp_priv, the
wrong calculation was used. Setting au_rslack == au_ralign is
probably correct for kerberos_v1 privacy, but kerberos_v2 privacy
adds additional GSS data after the clear text RPC message.
au_ralign needs to be smaller than au_rslack in that fairly common
case.
When xdr_buf_trim() is restored to gss_unwrap_kerberos_v2(), it does
exactly what I feared it would: it trims off part of the clear text
RPC message. However, that's because rpc_prepare_reply_pages() does
not set up the rq_rcv_buf's tail correctly because au_ralign is too
large.
Fixing the au_ralign computation also corrects the alignment of
rq_rcv_buf->pages so that the client does not have to shift reply
data payloads after they are received.
Fixes: 35e77d21ba ("SUNRPC: Add rpc_auth::au_ralign field")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Refactor: This is a pre-requisite to fixing the client-side ralign
computation in gss_unwrap_resp_priv().
The length value is passed in explicitly rather that as the value
of buf->len. This will subsequently allow gss_unwrap_kerberos_v1()
to compute a slack and align value, instead of computing it in
gss_unwrap_resp_priv().
Fixes: 35e77d21ba ("SUNRPC: Add rpc_auth::au_ralign field")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Instead of having all the sysctl handlers deal with user pointers, which
is rather hairy in terms of the BPF interaction, copy the input to and
from userspace in common code. This also means that the strings are
always NUL-terminated by the common code, making the API a little bit
safer.
As most handler just pass through the data to one of the common handlers
a lot of the changes are mechnical.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If the UDP header of a local VXLAN endpoint is NAT-ed, and the VXLAN
device has disabled UDP checksums and enabled Tx checksum offloading,
then the skb passed to udp_manip_pkt() has hdr->check == 0 (outer
checksum disabled) and skb->ip_summed == CHECKSUM_PARTIAL (inner packet
checksum offloaded).
Because of the ->ip_summed value, udp_manip_pkt() tries to update the
outer checksum with the new address and port, leading to an invalid
checksum sent on the wire, as the original null checksum obviously
didn't take the old address and port into account.
So, we can't take ->ip_summed into account in udp_manip_pkt(), as it
might not refer to the checksum we're acting on. Instead, we can base
the decision to update the UDP checksum entirely on the value of
hdr->check, because it's null if and only if checksum is disabled:
* A fully computed checksum can't be 0, since a 0 checksum is
represented by the CSUM_MANGLED_0 value instead.
* A partial checksum can't be 0, since the pseudo-header always adds
at least one non-zero value (the UDP protocol type 0x11) and adding
more values to the sum can't make it wrap to 0 as the carry is then
added to the wrapped number.
* A disabled checksum uses the special value 0.
The problem seems to be there from day one, although it was probably
not visible before UDP tunnels were implemented.
Fixes: 5b1158e909 ("[NETFILTER]: Add NAT support for nf_conntrack")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This bit indicates that the conntrack entry is offloaded to hardware
flow table. nf_conntrack entry will be tagged with [HW_OFFLOAD] if
it's offload to hardware.
cat /proc/net/nf_conntrack
ipv4 2 tcp 6 \
src=1.1.1.17 dst=1.1.1.16 sport=56394 dport=5001 \
src=1.1.1.16 dst=1.1.1.17 sport=5001 dport=56394 [HW_OFFLOAD] \
mark=0 zone=0 use=3
Note that HW_OFFLOAD/OFFLOAD/ASSURED are mutually exclusive.
Changelog:
* V1->V2:
- Remove check of lastused from stats. It was meant for cases such
as removing driver module while traffic still running. Better to
handle such cases from garbage collector.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This allows TC eBPF programs to modify and forward (redirect) packets
from interfaces without ethernet headers (for example cellular)
to interfaces with (for example ethernet/wifi).
The lack of this appears to simply be an oversight.
Tested:
in active use in Android R on 4.14+ devices for ipv6
cellular to wifi tethering offload.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
linux-next build bot reported compile issue [1] with one of its
configs. It looks like when we have CONFIG_NET=n and
CONFIG_BPF{,_SYSCALL}=y, we are missing the bpf_base_func_proto
definition (from net/core/filter.c) in cgroup_base_func_proto.
I'm reshuffling the code a bit to make it work. The common helpers
are moved into kernel/bpf/helpers.c and the bpf_base_func_proto is
exported from there.
Also, bpf_get_raw_cpu_id goes into kernel/bpf/core.c akin to existing
bpf_user_rnd_u32.
[1] https://lore.kernel.org/linux-next/CAKH8qBsBvKHswiX1nx40LgO+BGeTmb1NX8tiTttt_0uu6T3dCA@mail.gmail.com/T/#mff8b0c083314c68c2e2ef0211cb11bc20dc13c72
Fixes: 0456ea170c ("bpf: Enable more helpers for BPF_PROG_TYPE_CGROUP_{DEVICE,SYSCTL,SOCKOPT}")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200424235941.58382-1-sdf@google.com
Currently the following prog types don't fall back to bpf_base_func_proto()
(instead they have cgroup_base_func_proto which has a limited set of
helpers from bpf_base_func_proto):
* BPF_PROG_TYPE_CGROUP_DEVICE
* BPF_PROG_TYPE_CGROUP_SYSCTL
* BPF_PROG_TYPE_CGROUP_SOCKOPT
I don't see any specific reason why we shouldn't use bpf_base_func_proto(),
every other type of program (except bpf-lirc and, understandably, tracing)
use it, so let's fall back to bpf_base_func_proto for those prog types
as well.
This basically boils down to adding access to the following helpers:
* BPF_FUNC_get_prandom_u32
* BPF_FUNC_get_smp_processor_id
* BPF_FUNC_get_numa_node_id
* BPF_FUNC_tail_call
* BPF_FUNC_ktime_get_ns
* BPF_FUNC_spin_lock (CAP_SYS_ADMIN)
* BPF_FUNC_spin_unlock (CAP_SYS_ADMIN)
* BPF_FUNC_jiffies64 (CAP_SYS_ADMIN)
I've also added bpf_perf_event_output() because it's really handy for
logging and debugging.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200420174610.77494-1-sdf@google.com
Commit b656722906 ("net: Increase the size of skb_frag_t")
removed the 16bit limitation of a frag on some 32bit arches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile the kernel for arm 32 platform, the build warning found.
To fix that, should use div_u64() for divisions.
| net/openvswitch/meter.c:396: undefined reference to `__udivdi3'
[add more commit msg, change reported tag, and use div_u64 instead
of do_div by Tonghao]
Fixes: e57358873b ("net: openvswitch: use u64 for meter bucket")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix the following sparse warning:
| net/openvswitch/meter.c:109:38: sparse: sparse: incorrect type
| in assignment (different address spaces) ...
| net/openvswitch/meter.c:720:45: sparse: sparse: incorrect type
| in argument 1 (different address spaces) ...
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no callers in-tree since commit 792b48780e ("dccp: Implement
both feature-local and feature-remote Sequence Window feature")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hsr_dev_change_mtu(), the 'dev' and 'master->dev' pointer are
same. So, the 'master' variable and some code are unnecessary.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently subflow_finish_connect() changes unconditionally
any msk socket status other than TCP_ESTABLISHED.
If an unblocking connect() races with close(), we can end-up
triggering:
IPv4: Attempt to release TCP socket in state 1 00000000e32b8b7e
when the msk socket is disposed.
Be sure to enter the established status only from SYN_SENT.
Fixes: c3c123d16c ("net: mptcp: don't hang in mptcp_sendmsg() after TCP fallback")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In MPTCP, the receive window is shared across all subflows, because it
refers to the mptcp-level sequence space.
MPTCP receivers already place incoming packets on the mptcp socket
receive queue and will charge it to the mptcp socket rcvbuf until
userspace consumes the data.
Update __tcp_select_window to use the occupancy of the parent/mptcp
socket instead of the subflow socket in case the tcp socket is part
of a logical mptcp connection.
This commit doesn't change choice of initial window for passive or active
connections.
While it would be possible to change those as well, this adds complexity
(especially when handling MP_JOIN requests). Furthermore, the MPTCP RFC
specifically says that a MPTCP sender 'MUST NOT use the RCV.WND field
of a TCP segment at the connection level if it does not also carry a DSS
option with a Data ACK field.'
SYN/SYNACK packets do not carry a DSS option with a Data ACK field.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix memory leak in netfilter flowtable, from Roi Dayan.
2) Ref-count leaks in netrom and tipc, from Xiyu Yang.
3) Fix warning when mptcp socket is never accepted before close, from
Florian Westphal.
4) Missed locking in ovs_ct_exit(), from Tonghao Zhang.
5) Fix large delays during PTP synchornization in cxgb4, from Rahul
Lakkireddy.
6) team_mode_get() can hang, from Taehee Yoo.
7) Need to use kvzalloc() when allocating fw tracer in mlx5 driver,
from Niklas Schnelle.
8) Fix handling of bpf XADD on BTF memory, from Jann Horn.
9) Fix BPF_STX/BPF_B encoding in x86 bpf jit, from Luke Nelson.
10) Missing queue memory release in iwlwifi pcie code, from Johannes
Berg.
11) Fix NULL deref in macvlan device event, from Taehee Yoo.
12) Initialize lan87xx phy correctly, from Yuiko Oshino.
13) Fix looping between VRF and XFRM lookups, from David Ahern.
14) etf packet scheduler assumes all sockets are full sockets, which is
not necessarily true. From Eric Dumazet.
15) Fix mptcp data_fin handling in RX path, from Paolo Abeni.
16) fib_select_default() needs to handle nexthop objects, from David
Ahern.
17) Use GFP_ATOMIC under spinlock in mac80211_hwsim, from Wei Yongjun.
18) vxlan and geneve use wrong nlattr array, from Sabrina Dubroca.
19) Correct rx/tx stats in bcmgenet driver, from Doug Berger.
20) BPF_LDX zero-extension is encoded improperly in x86_32 bpf jit, fix
from Luke Nelson.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (100 commits)
selftests/bpf: Fix a couple of broken test_btf cases
tools/runqslower: Ensure own vmlinux.h is picked up first
bpf: Make bpf_link_fops static
bpftool: Respect the -d option in struct_ops cmd
selftests/bpf: Add test for freplace program with expected_attach_type
bpf: Propagate expected_attach_type when verifying freplace programs
bpf: Fix leak in LINK_UPDATE and enforce empty old_prog_fd
bpf, x86_32: Fix logic error in BPF_LDX zero-extension
bpf, x86_32: Fix clobbering of dst for BPF_JSET
bpf, x86_32: Fix incorrect encoding in BPF_LDX zero-extension
bpf: Fix reStructuredText markup
net: systemport: suppress warnings on failed Rx SKB allocations
net: bcmgenet: suppress warnings on failed Rx SKB allocations
macsec: avoid to set wrong mtu
mac80211: sta_info: Add lockdep condition for RCU list usage
mac80211: populate debugfs only after cfg80211 init
net: bcmgenet: correct per TX/RX ring statistics
net: meth: remove spurious copyright text
net: phy: bcm84881: clear settings on link down
chcr: Fix CPU hard lockup
...
Move the callback into the phylink_config structure, rather than
providing a callback to set this up.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Help end-users of the 'tc' command to see if the drivers ndo_setup_tc
function call fails. Troubleshooting when this happens is non-trivial
(see full process here[1]), and results in net_device getting assigned
the 'qdisc noop', which will drop all TX packets on the interface.
[1]: https://github.com/xdp-project/xdp-project/blob/master/areas/arm64/board_nxp_ls1088/nxp-board04-troubleshoot-qdisc.org
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix a wrong GFP_KERNEL in hwsim
* fix the debugfs mess after the mac80211 registration race fix
* suppress false-positive RCU list lockdep warnings
-----BEGIN PGP SIGNATURE-----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=SKNj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three changes:
* fix a wrong GFP_KERNEL in hwsim
* fix the debugfs mess after the mac80211 registration race fix
* suppress false-positive RCU list lockdep warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no callers in-tree.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
