common_task might be running while close routine is called,
wait/cancel it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware incorrectly process L0S/L1 entrance if the chipset/root
response after specific/shorter timer and cause system hang.
Enlarge the timeout value to avoid this issue.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platform with EEPROM/OTP existing, the BIOS could overwrite
a new MAC address for the NIC. so, the permanent mac address should
be from BIOS. the address is restored when driver removing.
Voltage raising isn't applicable for l1d.
Replace swab32 with htonl for big/little endian platform.
related Registers are refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Close-action is done by atl1c_reset_pcie, remove it from
atl1c_get_permanent_address.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL status is read-clear and should be cleared when in S0
status.
putting it in atl1c_reset_pcie is more suitable than
in atl1c_get_permanent_address.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms the PHY settings need to change depending on the
cable link status to get better stability.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
merge TXQ/RXQ/MAC start/enable code to one function as they
are started/enabled at the same time, just like stop/disable them
in the function of atl1c_stop_mac.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is used for suspend of S1/S3/S4 and driver remove.
It sets MAC/PHY based on the WoL configuation to get lower power
consumption.
atl1c_phy_power_saving is renamed to atl1c_phy_to_ps_link, this
function is just make PHY enter a link/speed mode to eat less
power.
REG_MAC_CTRL register is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it's unnecessary to reset/init phy when link down.
Only L1/L2 chip (supported by atlx) need such action.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many magic data are re-configured for PHY during its reset operation
based on chip type to get better compability and stability.
REG_PHY_CTRL register may be configured by BIOS before enter OS.
so, the driver can't directly write to it without any Read-Op.
this change also affect suspend and phy_disable routines.
PHY debug ports and extension registers are refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY polling code for FPGA is considered in every MDIO R/W API.
no need to add additional code to atl1c_open.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bit 17/18 of reg1424 must be clear for l2cb 1.x, or it will cause
the write-reg operation fail without cable connected.
so, please do connect the cable when apply this patch to the driver
to make sure these 2bits are cleared by new driver.
The revised code is move to al1c_reset_mac.
SERDES register definition is refined as well.
when do reset MAC, speed/duplex control right should be transferred
to software before do PHY auto-neg -- by bit MASTER_CTRL_SPEED_MODE_SW.
SERDES register definition is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atl1c_reset_phy follows atl1c_reset_pcie in the whole driver,
so, it's unnecessary to add PHY control code in atl1c_reset_pcie.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy register is read/write via MDIO control module ---
that module will be affected by the hibernate status,
to access phy regs in hib stutus, slow frequency clk must
be selected.
To access phy extension register, the MDIO related
registers are refined/updated, a _core function is
re-wroted for both regular PHY regs and extension regs.
existing PHY r/w function is revised based on the _core.
PHY extension registers will be used for the comming
patches.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this register is used for l1e(dev=1026)
l1c/l1d/l2cb don't use it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO_REG_ADDR_MASK is already applied in function
atl1c_write_phy_reg and atl1c_read_phy_reg
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2cb 1.1 hardware has a bug for magic wakeup,
the workaround is to add pattern enable.
WoL related registers are refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bit PCIE_PHYMISC_FORCE_RCV_DET is only for l1c&l2c to fix WoL issue,
other chips set bit5 of REG_MASTER_CTRL --- this way could save more
power than the former, and the bit should be kept all time.
l2cb 1.x has special setting for L0S/L1
l2cb 1.x & l1d 1.x should clear Vendor Message on some platforms,
otherwise it will cause the root complex hang.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
some platforms(BIOS or OS) may change ASPM configuration in
PCI Express Link Control Register directly and dynamically
regardless the device driver installation.
Checking if ASPM support during the driver init phase by reading
PCI Express Link Contrl Register doesn't make sense.
This refine/update assume L0S/L1 is defalut enabled as hw->ctrl_flags
inited. atl1c_set_aspm will set real configuration based on chip
capability to hardware register.
atl1c_disable_l0s_l1 and register definition of REG_PM_CTRL are
refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bit MASTER_CTRL_CLK_SEL_DIS could be set before enter suspend
clear it after resume to enable pclk(PCIE clock) switch to
low frequency(25M) in some circumstances to save power.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refine/update register REG_MASTER_CTRL definition according with
hardware spec.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clear PCIE error status (error log is write-1-clear).
REG_PCIE_UC_SEVERITY is removed as it's a standard pcie register,
and using kernle API to access it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dmar_dly_cnt and dmaw_dly_cnt aren't used by hardware/driver any more.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atl1c_configure_tx used a wrong value of MAX_TX_OFFLOAD_THRESH(9KB)
for TSO threshold.
the right value should be 7KB
Fast Ethernet controller doesn't support Jumbo frame.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l1c_wait_until_idle is called for serval modules (TXQ/RXQ/TXMAC/RXMAC).
specific moudle have specific idle/busy status in reg REG_IDLE_STATUS.
the previous code return wrongly if all modules are in idle status,
regardless the 'stop' action is applied on individual module.
Refine the reg REG_IDLE_STATUS definition as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
threshold setting to control ASPM for diff chips are different.
currently, all gigabit-capability chips have limited-ASPM under
100M throughput.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in some platforms, we found the max-read-request-size in Device Control
Register is set to 0 by (BIOS?) during bootup, this will cause the
performance(throughput) very bad.
Restore it to a min-value.
register definition of REG_DEVICE_CTRL is removed, using kernel API to
access it as it's a standard pcie register.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
using fixed TXQ config for l2cb and l1c regardless dmar_block
to make tx-DMA more stable.
register REG_TXQ_CTRL is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dmaw_block is never used in the driver, remove it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
some fields of REG_DMA_CTRL(15C0) are wrong, replace with the newest one.
haredware uses fixed dma-write-block size, remove dmaw_block related code
in function atl1c_configure_dma.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
function atl1c_stop_mac uses wrong register of REG_TWSI_CTRL
to stop mac, replace it with REG_TXQ_CTRL.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove code related to rxq 1/2/3 since multi-q not support.
refine REG_RXQ_CTRL definition as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TPD producer/consumer index is 16bit wide.
16bit read/write reduce the dependency of the 2 tpd rings (hi and lo)
rename reg(157C/1580) to keep name coninsistency.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l1c & later chips don't support DMA for SMB.
CMB is removed from hardware.
reg(15C8) is used to trig interrupt by tpd threshold.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VPD register is only used for L1(devid=PCI_DEVICE_ID_ATTANSIC_L1) to
access external NV-memory.
l1c & later chip doesn't use it any more.
PHY 0/1 registers occupy the last 2 slots of the dump table.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove HDS register as it doesn't exist in hardware.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the multiple-RX-Q in hardware doesn't work,
all related register definition & code are removed.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace unavailable email of the author since he left with a mail-list.
update company info as well, Atheros was acquired by Qualcomm.
insert "100" to driver description since it support 100M controller.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATL1C_WORK_EVENT_RESET is zero so the original code here is a nop. The
intent was to set the zero bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver attempts to use two TX rings but lacks proper support :
1) IRQ handler only takes care of TX completion on first TX ring
2) the stop/start logic uses the legacy functions (for non multiqueue
drivers)
This means all packets witk skb mark set to 1 are sent through high
queue but are never cleaned and queue eventualy fills and block the
device, triggering the infamous "NETDEV WATCHDOG" message.
Lets use a single TX ring to fix the problem, this driver is not a real
multiqueue one yet.
Minimal fix for stable kernels.
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Tested-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set addr_assign_type correctly to NET_ADDR_RANDOM in case
a random MAC address was generated and assigned to the netdevice.
Fix error handling in atl1c_probe(). If atl1c_read_mac_addr()
couldn't get the hw mac address, and a random mac address get
set return the error code. Don't go to err_eeprom in
atl1c_probe(), use the generated MAC address in this case.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: use bitops
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Atheros drivers into drivers/net/ethernet/atheros/ and
make the necessary Kconfig and Makefile changes.
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
