struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-23-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Initialize on-stack modes with drm_mode_init() to guarantee
no stack garbage in the list head, or that we aren't copying
over another mode's list head.
Based on the following cocci script, with manual fixups:
@decl@
identifier M;
expression E;
@@
- struct drm_display_mode M = E;
+ struct drm_display_mode M;
@@
identifier decl.M;
expression decl.E;
statement S, S1;
@@
struct drm_display_mode M;
... when != S
+ drm_mode_init(&M, &E);
+
S1
@@
expression decl.E;
@@
- &*E
+ E
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-22-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
In komeda_plane_add(), komeda_get_layer_fourcc_list() is assigned to
formats and used in drm_universal_plane_init().
drm_universal_plane_init() passes formats to
__drm_universal_plane_init(). __drm_universal_plane_init() further
passes formats to memcpy() as src parameter, which could lead to an
undefined behavior bug on failure of komeda_get_layer_fourcc_list().
Fix this bug by adding a check of formats.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_DRM_KOMEDA=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 61f1c4a8ab ("drm/komeda: Attach komeda_dev to DRM-KMS")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://lore.kernel.org/dri-devel/20211201033704.32054-1-zhou1615@umn.edu
A specialisation of the generic Synopsys HDMI driver is employed for
JZ4780 HDMI support. This requires a new driver, plus device tree and
configuration modifications.
Here we add Kconfig DRM_INGENIC_DW_HDMI, Makefile and driver code.
Note that there is no hpd-gpio installed on the CI20 board HDMI
connector. Hence there is no hpd detection by the connector driver
and we have to enable polling in the dw-hdmi core driver.
For that we need to set .poll_enabled but that struct component
can only be accessed by core code. Hence we use the public
setter function drm_kms_helper_hotplug_event() introduced before.
Also note that we disable Color Space Conversion since it is not
working on jz4780.
Signed-off-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/e5cdf9cd44bde52cce379cc830f2d6117ea15c32.1649330171.git.hns@goldelico.com
Add a simple check to reject any size not aligned to the
min_page_size.
when size is not aligned to min_page_size, driver module
should handle in their own way either to round_up() the
size value to min_page_size or just to enable WARN_ON().
If we dont handle the alignment properly, we may hit the
following bug, Unigine Heaven has allocation requests for
example required pages are 257 and alignment request is 256.
To allocate the left over 1 page, continues the iteration to
find the order value which is 0 and when it compares with
min_order = 8, triggers the BUG_ON(order < min_order).
v2: add more commit description
v3: remove WARN_ON()
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Suggested-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411073834.15210-1-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
If we use a format that has padding instead of the alpha component (such
as XRGB8888), it appears that the Transposer will fill the padding to 0,
disregarding what was stored in the input buffer padding.
This leads to issues with IGT, since it will set the padding to 0xff,
but will then compare the CRC of the two frames which will thus fail.
Another nice side effect is that it is now possible to just use the
buffer as ARGB.
Fixes: 008095e065 ("drm/vc4: Add support for the transposer block")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220328153659.2382206-4-maxime@cerno.tech
The TXP_VSTART_AT_EOF will generate a second VSTART signal to the HVS.
However, the HVS waits for VSTART to enable the FIFO and will thus start
filling the FIFO before the start of the frame.
This leads to corruption at the beginning of the first frame, and
content from the previous frame at the beginning of the next frames.
Since one VSTART is enough, let's get rid of it.
Fixes: 008095e065 ("drm/vc4: Add support for the transposer block")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220328153659.2382206-3-maxime@cerno.tech
By default, the HVS driver will force the HVS output 3 to be muxed to
the HVS channel 2. However, the Transposer can only be assigned to the
HVS channel 2, so whenever we try to use the writeback connector, we'll
mux its associated output (Output 2) to the channel 2.
This leads to both the output 2 and 3 feeding from the same channel,
which is explicitly discouraged in the documentation.
In order to avoid this, let's reset all the output muxes to their reset
value.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220328153659.2382206-2-maxime@cerno.tech
- Switch to drm buddy allocator
- Add resource cursor support for drm buddy
v2(Matthew Auld):
- replace spinlock with mutex as we call kmem_cache_zalloc
(..., GFP_KERNEL) in drm_buddy_alloc() function
- lock drm_buddy_block_trim() function as it calls
mark_free/mark_split are all globally visible
v3(Matthew Auld):
- remove trim method error handling as we address the failure case
at drm_buddy_block_trim() function
v4:
- fix warnings reported by kernel test robot <lkp@intel.com>
v5:
- fix merge conflict issue
v6:
- fix warnings reported by kernel test robot <lkp@intel.com>
v7:
- remove DRM_BUDDY_RANGE_ALLOCATION flag usage
v8:
- keep DRM_BUDDY_RANGE_ALLOCATION flag usage
- resolve conflicts created by drm/amdgpu: remove VRAM accounting v2
v9(Christian):
- merged the below patch
- drm/amdgpu: move vram inline functions into a header
- rename label name as fallback
- move struct amdgpu_vram_mgr to amdgpu_vram_mgr.h
- remove unnecessary flags from struct amdgpu_vram_reservation
- rewrite block NULL check condition
- change else style as per coding standard
- rewrite the node max size
- add a helper function to fetch the first entry from the list
v10(Christian):
- rename amdgpu_get_node() function name as amdgpu_vram_mgr_first_block
v11:
- if size is not aligned with min_page_size, enable is_contiguous flag,
therefore, the size round up to the power of two and trimmed to the
original size.
v12:
- rename the function names having prefix as amdgpu_vram_mgr_*()
- modify the round_up() logic conforming to contiguous flag enablement
or if size is not aligned to min_block_size
- modify the trim logic
- rename node as block wherever applicable
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407224843.2416-1-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
The commit 73511edf8b ("dma-buf: specify usage while adding fences to
dma_resv obj v7") ported all the DRM drivers to use the newer fence API
that specifies the usage with the enum dma_resv_usage rather than doing
an explicit shared / exclusive distinction.
But the commit didn't do it properly in two callers of the vc4 driver,
leading to build errors.
Fixes: 73511edf8b ("dma-buf: specify usage while adding fences to dma_resv obj v7")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407131950.915091-1-javierm@redhat.com
The SINO WEALTH SH1106 is an OLED display driver that is somewhat
compatible with the SSD1306. It supports a slightly wider display,
at 132 instead of 128 pixels. The basic commands are the same, but
the SH1106 doesn't support the horizontal or vertical address modes.
Add support for this display driver. The default values for some of
the hardware settings are taken from the datasheet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220406172956.3953-5-wens@kernel.org
On the SINO WEALTH SH1106, which is mostly compatible with the SSD1306,
only the basic page addressing mode is supported. This addressing mode
is not as easy to use compared to the currently supported horizontal
addressing mode, as the page address has to be set prior to writing
out each page, and each page must be written out separately as a result.
Also, there is no way to force the column address to wrap around early,
thus the column address must also be reset for each page to be accurate.
Add support for this addressing mode, with a flag to choose it. This
flag is designed to be set from the device info data structure, but
can be extended to be explicitly forced on through a device tree
property if such a need arises.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220406172956.3953-4-wens@kernel.org
Add an usage for kernel submissions. Waiting for those are mandatory for
dynamic DMA-bufs.
As a precaution this patch also changes all occurrences where fences are
added as part of memory management in TTM, VMWGFX and i915 to use the
new value because it now becomes possible for drivers to ignore fences
with the WRITE usage.
v2: use "must" in documentation, fix whitespaces
v3: separate out some driver changes and better document why some
changes should still be part of this patch.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407085946.744568-5-christian.koenig@amd.com
Instead of distingting between shared and exclusive fences specify
the fence usage while adding fences.
Rework all drivers to use this interface instead and deprecate the old one.
v2: some kerneldoc comments suggested by Daniel
v3: fix a missing case in radeon
v4: rebase on nouveau changes, fix lockdep and temporary disable warning
v5: more documentation updates
v6: separate internal dma_resv changes from this patch, avoids to
disable warning temporary, rebase on upstream changes
v7: fix missed case in lima driver, minimize changes to i915_gem_busy_ioctl
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407085946.744568-3-christian.koenig@amd.com
This change adds the dma_resv_usage enum and allows us to specify why a
dma_resv object is queried for its containing fences.
Additional to that a dma_resv_usage_rw() helper function is added to aid
retrieving the fences for a read or write userspace submission.
This is then deployed to the different query functions of the dma_resv
object and all of their users. When the write paratermer was previously
true we now use DMA_RESV_USAGE_WRITE and DMA_RESV_USAGE_READ otherwise.
v2: add KERNEL/OTHER in separate patch
v3: some kerneldoc suggestions by Daniel
v4: some more kerneldoc suggestions by Daniel, fix missing cases lost in
the rebase pointed out by Bas.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407085946.744568-2-christian.koenig@amd.com
Don't mark static functions as kernel-doc.
Prevents multiple kernel-doc build warnings:
drivers/gpu/drm/sti/sti_hdmi.c:187: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* HDMI interrupt handler threaded
drivers/gpu/drm/sti/sti_hdmi.c:219: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* HDMI interrupt handler
drivers/gpu/drm/sti/sti_hdmi.c:241: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Set hdmi active area depending on the drm display mode selected
drivers/gpu/drm/sti/sti_hdmi.c:262: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Overall hdmi configuration
drivers/gpu/drm/sti/sti_hdmi.c:340: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Helper to concatenate infoframe in 32 bits word
drivers/gpu/drm/sti/sti_hdmi.c:357: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Helper to write info frame
drivers/gpu/drm/sti/sti_hdmi.c:427: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Prepare and configure the AVI infoframe
drivers/gpu/drm/sti/sti_hdmi.c:470: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Prepare and configure the AUDIO infoframe
drivers/gpu/drm/sti/sti_hdmi.c:555: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Software reset of the hdmi subsystem
Fixes: 5402626c83 ("drm: sti: add HDMI driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Alain Volmat <alain.volmat@foss.st.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220326235132.25192-1-rdunlap@infradead.org
The two bugs are here:
if (encoder) {
if (bridge && bridge->timings)
The list iterator value 'encoder/bridge' will *always* be set and
non-NULL by drm_for_each_encoder()/list_for_each_entry(), so it is
incorrect to assume that the iterator value will be NULL if the
list is empty or no element is found.
To fix the bug, use a new variable '*_iter' as the list iterator,
while use the old variable 'encoder/bridge' as a dedicated pointer
to point to the found element.
Cc: stable@vger.kernel.org
Fixes: 99e360442f ("drm/stm: Fix bus_flags handling")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Acked-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220327055355.3808-1-xiam0nd.tong@gmail.com
atomic_flush will be called for each CRTC even if they aren't enabled.
The whole code we have there will thus run without a properly affected
channel, which can then result in all sorts of weird behaviour.
Fortunately, the DRM_PLANE_COMMIT_ACTIVE_ONLY flag will skip the CRTC
atomic_begin and atomic_flush, and the planes atomic_update, if they
aren't enabled.
Our plane atomic_update is a nop, and atomic_begin will copy the current
HVS channel to the vc4_crtc structure for the interrupt handler to
consume, but the handler won't run if the CRTC is disabled. So in the
end, it will only skip our CRTC atomic_flush, which is what we want.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220331143744.777652-7-maxime@cerno.tech
The vc4_hvs_update_dlist function mostly deals with setting up the
vblank events and setting up the dlist entry pointer to our current
active one.
We'll want to do the former separately from the vblank handling in later
patches, so let's move it to a function of its own.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220331143744.777652-6-maxime@cerno.tech
In order to get the field currently being output, the driver has been
using the display FIFO frame count in the HVS, reading a 6-bit field at
the offset 12 in the DISPSTATx register.
While that field is indeed at that location for the FIFO 1 and 2, the
one for the FIFO0 is actually in the DISPSTAT1 register, at the offset
18.
Fixes: e538092cb1 ("drm/vc4: Enable precise vblank timestamping for interlaced modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220331143744.777652-3-maxime@cerno.tech
During a commit, the core clock, which feeds the HVS, needs to run at
a minimum of 500MHz.
While doing that commit, we can also change the mode to one that
requires a higher core clock, so we take the core clock rate associated
to that new state into account for that boost.
However, the old state also needs to be taken into account if it
requires a core clock higher that the new one and our 500MHz limit,
since it's still live in hardware at the beginning of our commit.
Fixes: 16e101051f ("drm/vc4: Increase the core clock based on HVS load")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220331143744.777652-2-maxime@cerno.tech
