This patch adds the functionality and APIs needed for selftests.
It adds the ability to configure the link-mode which is required for the
implementation of loopback tests. It adds the APIs for clock test,
register test, interrupt test and memory test.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure ds is actually needed in very few places,
mostly during setup of the switch. The private structure ps is however
needed nearly everywhere. Pass ps, not ds internally.
[vd: rebased Andrew's patch.]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-05-01
This series contains updates to i40e and i40evf.
The theme of this series is code reduction, with several code cleanups in
this series. Starting with Neerav's removal of the code that implemented
the HMC AQ APIs and calls, since they are now obsolete and not supported
by firmware.
Anjali changes the default of VFs to make sure they are not trusted or
privileged until its explicitly set for trust through the new NDO op
interface. Also limited the number of MAC and VLAN addresses a VF can
add if it is untrusted/privileged.
Carolyn syncs the VF code for the changes made to the PF for the RSS
hash tuple settings, which ends up cleaning up much of the existing code.
Jesse cleans up compiler warnings which were found with gcc's W=2 option.
Then removed duplicate code, especially since only one copy was actually
being used.
Jacob addresses an issue which was found when testing GCC 6's which
happens to produce new warnings when you left shift a signed value
beyond the storage sizeof the type. The converts i40e & i40evf to use
the BIT() macro more consistently.
Alex actually bucks the trend of code removal by adding support for
both drivers to use GSO_PARTIAL so that segmentation of frames with
checksums enabled in outer headers is supported. Fortunately it does
not take much to add this support!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Miller pointed out that fb586f2530 ("sctp: delay calls to
sk_data_ready() as much as possible") may insert latency specially if
the receiving application is running on another CPU and that it would be
better if we signalled as early as possible.
This patch thus basically inverts the logic on fb586f2530 and signals
it as early as possible, similar to what we had before.
Fixes: fb586f2530 ("sctp: delay calls to sk_data_ready() as much as possible")
Reported-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b74766a0a0 ("phylib: don't return NULL
from get_phy_device()") in linux-next, phy_get_device() will return
ERR_PTR(-ENODEV) instead of NULL if the PHY device ID is all ones.
This causes problem with stmmac driver and likely some other drivers
which call mdiobus_register(). I triggered this bug on SoCFPGA MCVEVK
board with linux-next 20160427 and 20160428. In case of the stmmac, if
there is no PHY node specified in the DT for the stmmac block, the stmmac
driver ( drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c function
stmmac_mdio_register() ) will call mdiobus_register() , which will
register the MDIO bus and probe for the PHY.
The mdiobus_register() resp. __mdiobus_register() iterates over all of
the addresses on the MDIO bus and calls mdiobus_scan() for each of them,
which invokes get_phy_device(). Before the aforementioned patch, the
mdiobus_scan() would return NULL if no PHY was found on a given address
and mdiobus_register() would continue and try the next PHY address. Now,
mdiobus_scan() returns ERR_PTR(-ENODEV), which is caught by the
'if (IS_ERR(phydev))' condition and the loop exits immediately if the
PHY address does not contain PHY.
Repair this by explicitly checking for the ERR_PTR(-ENODEV) and if this
error comes around, continue with the next PHY address.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that i40e and i40evf can use GSO_PARTIAL to support
segmentation for frames with checksums enabled in outer headers. As a
result we can now send data over these types of tunnels at over 20Gb/s
versus the 12Gb/s that was previously possible on my system.
The advantage with the i40e parts is that this offload is mostly
transparent as the hardware still deals with the inner and/or outer IPv4
headers so the IP ID is still incrementing for both when this offload is
performed.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
GCC 6 has a new warning which will display when you attempt to left
shift a signed value beyond the storage size of the type. I40E_MASK
generates a mask value for 32bit registers. Properly typecast the mask
value and place the values in parenthesis to prevent macro expansion
issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a device ID for X722.
Change-Id: I574f2345ab341de98a6a1c212d0603af853e48b0
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_release_rx_desc was in two files, but was only used
and needed in txrx.c. Get rid of the extra copy.
Change-Id: I86e18239aa03531fc198b6c052847475084a9200
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was all over the place using signed or unsigned types
for vf_id, when it should always be signed.
This fixes warnings of type unsafe comparisons from gcc with W=2.
Change-Id: I2cb681f83d0f68ca124d2e4131e4ac0d9f8a6b22
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Aggregate return warnings are when struct types are returned
and must be copied to the lvalue with a struct copy by the compiler.
This fixes warnings of type aggregate-return from gcc with W=2.
Change-Id: I896b1bf514544bf0faeb458869d79914b9f1b168
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have an uninitialized variable warning for valid_len for one case in
validate_vf_mesg. To fix this, just initialize it to 0 at the top of the
function and remove all of the now redundant assignments to 0 in the
individual cases.
Change-Id: Iacbd97f4c521ed8d662eef803a598d8707708cfd
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch syncs the VF code for the changes made to the PF for the RSS
hash tuple settings. Since the VF still cannot change the RSS hash
settings, change the code to make this clear to the user. Previously,
the default settings were returned in this function. However, the
default can be changed by the PF so this does not make sense anymore.
Change-Id: I085eaf005fc7978b440d2a1bf2b2dd7cadaff39b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the code that implements the HMC AQ APIs and call these APIs.
This is done because these are obsolete APIs and are not supported
by firmware.
Change-ID: I5d771d8f37c3e16e7b0a972ff9b27e75aa2d05d4
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this change a non trusted VF can never fall to promiscuous
mode when there is no room for a MAC/VLAN filter.
Change-Id: I8a155aa25c0bcdc6093414920c9ade4ee0bd20e8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF is privileged/trusted it can do as it may please including
but not limited to hogging resources and playing unfair.
But if the VF is not privileged/trusted it still can add some number
(8) of MAC and VLAN addresses.
Other restrictions with respect to Port VLAN and normal VLAN still apply
to not privileged/trusted VF.
Change-Id: I3a9529201b184c8873e1ad2e300aff468c9e6296
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we are displaying statistics for the first link established between
two peers, it will always be presented as STANDBY although it in reality
is ACTIVE.
This happens because we forget to set the 'active' flag in the link
instance at the moment it is established. Although this is a bug, it only
has impact on the presentation view of the link, not on its actual
functionality.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a check whether the 'struct device_node' pointer passed to
of_mdiobus_register() is an available (aka enabled) node in the Device
Tree.
Rationale for doing this are cases where an Ethernet MAC provides a MDIO
bus controller and node, and an additional Ethernet MAC might be
connecting its PHY/switches to that first MDIO bus controller, while
still embedding one internally which is therefore marked as "disabled".
Instead of sprinkling checks like these in callers of
of_mdiobus_register(), do this in a central location.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure a VF is not trusted/privileged until its explicitly
set for trust through the new NDO op interface.
Change-Id: I476385c290d2b4901d8fceb29de43546accdc499
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Saeed Mahameed says:
====================
Mellanox 100G mlx5 ethernet aRFS support
This series adds accelerated RFS support for the mlx5e driver.
I have added one patch non-related to aRFS that fixes the rtnl_lock
warning mlx5 driver been getting since b7aade1548 ('vxlan: break dependency with netdev drivers')
aRFS support in details:
A direct TIR per RQ is now required in order to have the essential building blocks
for aRFS. Today the driver has one direct TIR that forwards traffic to RQ[0] (core 0),
and one indirect TIR for RSS indirection table. For that we've added one direct TIR
per RQ, e.g.: TIR[i] -> RQ[i] (core i).
Publicize Modify flow rule destination and reveal it in flow steering API, to have the
ability to dynamically modify the destination TIR(core) for aRFS rules from the
ethernet driver.
Initializing CPU reverse mapping to notify upper layer on internal receive queue cpu
mappings.
Some design refactoring for mlx5e ethernet driver flow tables and flow steering API.
Now the caller of create_flow_table can choose the level of the flow table, this way
we will create the mlx5e flow tables in a reversed order and connect them as we go,
we create flow table[i+1] before flow table[i] to be able to set flow table[i + 1] as
a destination of flow table[i] once flow table[i] is created.
also we have split the main flow table in the following manner:
- From before: RX packet had to visit two flow tables until it is delivered to its receive queue:
RX packet -> vlan filter flow table -> main flow table.
> vlan filter will check the packet vlan field is allowed.
> main flow will check if the dest mac is allowed and will check the l3/l4 headers to
retrieve the RSS hash for steering the packet into its final receive queue.
- Now main flow table is split into l2 dst mac steering table and ttc (traffic type classifier) table:
RX packet -> vlan filter -> l2 table -> ttc table
> vlan filter - same as before
> L2 filter - filter packets according their destination mac address
> ttc table - classify packet headers for RSS steering
- L3/L4 classification rules to steer the packet according to thier headers hash
- in case of none of the rules applies the packet is steered to RQ[0]
After the above refactoring all left to-do is to create aRFS flow table which will manage
aRFS steering rules to forward traffic to the desired RQ (core) and just connect the ttc
table rules destinations to aRFS flow table.
aRFS flow table in case of a miss will deliver the traffic to the core where the original
ttc hash would have chosen.
TTC table is not initialized and enabled until the user explicitly asks to, i.e. setting the NETIF_F_NTUPLE
to ON. This way there is no need for ttc table to forward traffic to aRFS table unless required.
When setting back to OFF aRFS flow table is disabled and disconnected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Accelerated RFS requires that ntuple filtering is enabled via
ethtool and driver supports ndo_rx_flow_steer.
When the ntuple filtering is enabled, we modify the l3_l4 ttc
rules to point on the aRFS flow tables and when the filtering
is disabled, we modify the l3_l4 ttc rules to point on the RSS
TIRs.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_rx_flow_steer ndo.
A new flow steering rule will be composed from the
skb 4-tuple and added to the hardware aRFS flow table.
Each rule is stored in an internal hash table, if such
skb 4-tuple rule already exists we update the corresponding
hardware steering rule with the new destination.
For garbage collection rps_may_expire_flow will be
invoked for a limited amount of old rules upon any
ndo_rx_flow_steer invocation.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create the following four flow tables for aRFS usage:
1. IPv4 TCP - filtering 4-tuple of IPv4 TCP packets.
2. IPv6 TCP - filtering 4-tuple of IPv6 TCP packets.
3. IPv4 UDP - filtering 4-tuple of IPv4 UDP packets.
4. IPv6 UDP - filtering 4-tuple of IPv6 UDP packets.
Each flow table has two flow groups: one for the 4-tuple
filtering (full match) and the other contains * rule for miss rule.
Full match rule means a hit for aRFS and packet will be forwarded
to the dedicated RQ/Core, miss rule packets will be forwarded to
default RSS hashing.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating CPU rmap and add entry for each IRQ.
CPU rmap is used in aRFS to get the RX queue number
of the RX completion interrupts.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the main flow table is used for two purposes:
One is to do mac filtering and the other is to classify
the packet l3-l4 header in order to steer the packet to
the right RSS TIR.
This design is very complex, for each configured mac address we
have to add eleven rules (rule for each traffic type), the same if the
device is put to promiscuous/allmulti mode.
This scheme isn't scalable for future features like aRFS.
In order to simplify it, the main flow table is split to two flow
tables:
1. l2 table - filter the packet dmac address, if there is a match
we forward to the ttc flow table.
2. TTC (Traffic Type Classifier) table - classify the traffic
type of the packet and steer the packet to the right TIR.
In this new design, when new mac address is added, the driver adds
only one flow rule instead of eleven.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slightly refactor and re-order the flow steering structs,
tables and data-bases for better self-containment and
flexibility to add more future steering phases
(tables/rules/data bases) e.g: aRFS.
Changes:
1. Move the vlan DB and address DB into their table structs.
2. Rename steering table structs to unique format: mlx5e_*_table,
e.g: mlx5e_vlan_table.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, namespace could be initialized only
with priorities with the same attributes.
Add support to initialize namespace with priorities
with different attributes(e.g. different number of levels).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, consumers of the flow steering infrastructure can't
choose their own flow table levels and are limited to one
flow table per level. This just waste levels.
Instead, we introduce here the possibility to use multiple
flow tables in a level. The user is free to connect these
flow tables, while following the rule (FTEs in FT of level x
could only point to FTs of level y where y > x).
In addition this patch switch the order of the create/destroy
flow tables of the NIC(vlan and main).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactors the flow steering namespace creation,
by changing the name num_fts to num_levels.
When new flow table is created, the driver assign new level
to this flow table therefore the meaning is equivalent.
Since downstream patches will introduce the ability to create more
than one flow table per level, the name num_fts is no
longer accurate.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This API is used for modifying the flow rule destination.
This is needed for modifying the pointed flow table by the
traffic type classifier rules to point on the aRFS tables.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new TIRs for direct access per RQ.
Now we have 2 available kinds of TIRs:
- indirect TIR per traffic type, each points to one RQT (RSS RQT)
same as before.
- New direct TIR per RQ, each points to RQT with a size of one
that forwards packets to that RQ only.
Driver will open max channels (num cores) direct TIRs by default,
they will be filled with the actual RQs once channels are allocated.
Needed for downstream aRFS and ethtool direct steering functionalities.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold the rtnl lock when calling vxlan_get_rx_port().
Fixes: b7aade1548 ("vxlan: break dependency with netdev drivers")
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Heimpold says:
====================
net: ethernet: enc28j60: small improvements
This series of two patches adds the following improvements to the driver:
1) Rework the central SPI read function so that it is compatible with
SPI masters which only support half duplex transfers.
2) Add a device tree binding for the driver.
Changelog:
v3: * renamed and improved binding documentation as
suggested by Rob Herring
v2: * took care of Arnd Bergmann's review comments
- allow to specify MAC address via DT
- unconditionally define DT id table
* increased the driver version minor number
* driver author's email address bounces, removed from address list
v1: * Initial submission
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch adds the required match table for device tree support
(and while at, fix the indent). It's also possible to specify the
MAC address in the DT blob.
Also add the corresponding binding documentation file.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current spi_read_buf function fails on SPI host masters which
are only half-duplex capable. Splitting the Tx and Rx part solves
this issue.
Tested on Raspberry Pi (full duplex) and I2SE Duckbill (half duplex).
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
is_skb_forwardable is not supposed to change anything so constify its
arguments
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault says:
====================
ppp: add rtnetlink support
PPP devices lack the ability to be customised at creation time. In
particular they can't be created in a given netns or with a particular
name. Moving or renaming the device after creation is possible, but
creates undesirable transient effects on servers where PPP devices are
constantly created and removed, as users connect and disconnect.
Implementing rtnetlink support solves this problem.
The rtnetlink handlers implemented in this series are minimal, and can
only replace the PPPIOCNEWUNIT ioctl. The rest of PPP ioctls remains
necessary for any other operation on channels and units.
It is perfectly possible to mix PPP devices created by rtnl
and by ioctl(PPPIOCNEWUNIT). Devices will behave in the same way.
mutex_trylock() is used to resolve the locking issue wrt. locking
dependency between rtnl_lock() and ppp_mutex (see ppp_nl_newlink() in
patch #2).
A user visible difference brought by this series is that old PPP
interfaces (those created with ioctl(PPPIOCNEWUNIT)), can now be
removed by "ip link del", just like new rtnl based PPP devices.
Changes since v3:
- Rebase on net-next.
- Not an RFC anymore.
Changes since v2:
- Define ->rtnl_link_ops for ioctl based PPP devices, so they can
handle rtnl messages just like rtnl based ones (suggested by
Stephen Hemminger).
- Move back to original lock ordering between ppp_mutex and rtnl_lock
to simplify patch series. Handle lock inversion issue using
mutex_trylock() (suggested by Stephen Hemminger).
- Do file descriptor lookup directly in ppp_nl_newlink(), to simplify
ppp_dev_configure().
Changes since v1:
- Rebase on net-next.
- Invert locking order wrt. ppp_mutex and rtnl_lock and protect
file->private_data with ppp_mutex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define PPP device handler for use with rtnetlink.
The only PPP specific attribute is IFLA_PPP_DEV_FD. It is mandatory and
contains the file descriptor of the associated /dev/ppp instance (the
file descriptor which would have been used for ioctl(PPPIOCNEWUNIT) in
the ioctl-based API). The PPP device is removed when this file
descriptor is released (same behaviour as with ioctl based PPP
devices).
PPP devices created with the rtnetlink API behave like the ones created
with ioctl(PPPIOCNEWUNIT). In particular existing ioctls work the same
way, no matter how the PPP device was created.
The rtnl callbacks are also assigned to ioctl based PPP devices. This
way, rtnl messages have the same effect on any PPP devices.
The immediate effect is that all PPP devices, even ioctl-based
ones, can now be removed with "ip link del".
A minor difference still exists between ioctl and rtnl based PPP
interfaces: in the device name, the number following the "ppp" prefix
corresponds to the PPP unit number for ioctl based devices, while it is
just an unrelated incrementing index for rtnl ones.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move PPP device initialisation and registration out of
ppp_create_interface().
This prepares code for device registration with rtnetlink.
While there, simplify the prototype of ppp_create_interface():
* Since ppp_dev_configure() takes care of setting file->private_data,
there's no need to return a ppp structure to ppp_unattached_ioctl()
anymore.
* The unit parameter is made read/write so that ppp_create_interface()
can tell which unit number has been assigned.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
On new GMAC4 IP, MAC_MDIO_address register has been updated, and bitmaps
changed. This patch takes into account those changes.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0c867c9bf8 ("vxlan: move Ethernet initialization to a separate
function") changed initialization order and as an unintended result, when the
user specifies additional link parameters (such as IFLA_ADDRESS) while
creating vxlan interface, those are overwritten by vxlan_ether_setup later.
It's necessary to call ether_setup from withing the ->setup callback. That
way, the correct parameters are set by rtnl_create_link later. This is done
also for VXLAN-GPE, as we don't know the interface type yet at that point,
and changed to the correct interface type later.
Fixes: 0c867c9bf8 ("vxlan: move Ethernet initialization to a separate function")
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Tested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer says:
====================
samples/bpf: Improve user experience
It is a steep learning curve getting started with using the eBPF
examples in samples/bpf/. There are several dependencies, and
specific versions of these dependencies. Invoking make in the correct
manor is also slightly obscure.
This patchset cleanup, document and hopefully improves the first time
user experience with the eBPF samples directory by auto-detecting
certain scenarios.
V4:
- Address Naveen's nitpicks
- Handle/fail if extra args are passed in LLC or CLANG (David Laight)
V3:
- Add Alexei's ACKs
- Remove README paragraph about LLVM experimental BPF target
as it only existed between LLVM version 3.6 to 3.7.
V2:
- Adjusted recommend minimum versions to 3.7.1
- Included clang build instructions
- New patch adding CLANG variable and validation of command
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Users are likely to manually compile both LLVM 'llc' and 'clang'
tools. Thus, also allow redefining CLANG and verify command exist.
Makefile implementation wise, the target that verify the command have
been generalized.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not intuitive that 'make' must be run from the top level
directory with argument "samples/bpf/" to compile these eBPF samples.
Introduce a kbuild make file trick that allow make to be run from the
"samples/bpf/" directory itself. It basically change to the top level
directory and call "make samples/bpf/" with the "/" slash after the
directory name.
Also add a clean target that only cleans this directory, by taking
advantage of the kbuild external module setting M=$PWD.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting started with using examples in samples/bpf/ is not
straightforward. There are several dependencies, and specific
versions of these dependencies.
Just compiling the example tool is also slightly obscure, e.g. one
need to call make like:
make samples/bpf/
Do notice the "/" slash after the directory name.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make compiling samples/bpf more user friendly, by detecting if LLVM
compiler tool 'llc' is available, and also detect if the 'bpf' target
is available in this version of LLVM.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is practical to be-able-to redefine the location of the LLVM
command 'llc', because not all distros have a LLVM version with bpf
target support. Thus, it is sometimes required to compile LLVM from
source, and sometimes it is not desired to overwrite the distros
default LLVM version.
This feature was removed with 128d1514be ("samples/bpf: Use llc in
PATH, rather than a hardcoded value").
Add this features back. Note that it is possible to redefine the LLC
on the make command like:
make samples/bpf/ LLC=~/git/llvm/build/bin/llc
Fixes: 128d1514be ("samples/bpf: Use llc in PATH, rather than a hardcoded value")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
