It is erroneous to update the TTY port baud rate if it hasn't been
initialized yet, because in that case the TTY struct isn't set. So there
is no termios structure to get and re-calculate the baud if the current
baud can't be reached. Let's skip the baud rate update then until the port
is fully initialized.
Note the update UART clock method still sets the uartclk member with a new
ref clock value even if the port is turned off. The new UART ref clock
rate will be used later on the port starting up procedure.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the port of the commit db1b5bc047 ("serial: 8250: Fix TX
interrupt handling condition") to the 8250_fsl irq handling logic.
Interrupt handler checked THRE bit (transmitter holding register
empty) in LSR to detect if TX fifo is empty.
In case when there is only receive interrupts the TX handling
got called because THRE bit in LSR is set when there is no
transmission (FIFO empty). TX handling caused TX stop, which in
RS-485 half-duplex mode actually resets receiver FIFO. This is not
desired during reception because of possible data loss.
The fix is to check if THRI is set in IER in addition of the TX
fifo status. THRI in IER is set when TX is started and cleared
when TX is stopped.
This ensures that TX handling is only called when there is really
transmission on going and an interrupt for THRE and not when there
are only RX interrupts.
Signed-off-by: Andrij Abyzov <aabyzov@slb.com>
Link: https://lore.kernel.org/r/20200928144127.87156-1-aabyzov@slb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the tty/serial fixes in here and this resolves a merge issue in
the 8250 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial fixes from Greg KH:
"Here are a few small TTY/Serial/vt fixes for 5.9-rc3
Included in here are:
- qcom serial fixes
- vt ioctl and core bugfixes
- pl011 serial driver fixes
- 8250 serial driver fixes
- other misc serial driver fixes
and for good measure:
- fbcon fix for syzbot found problem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: imx: add dependence and build for earlycon
serial: samsung: Removes the IRQ not found warning
serial: 8250: change lock order in serial8250_do_startup()
serial: stm32: avoid kernel warning on absence of optional IRQ
serial: pl011: Fix oops on -EPROBE_DEFER
serial: pl011: Don't leak amba_ports entry on driver register error
serial: 8250_exar: Fix number of ports for Commtech PCIe cards
tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setup
serial: qcom_geni_serial: Fix recent kdb hang
vt_ioctl: change VT_RESIZEX ioctl to check for error return from vc_resize()
fbcon: prevent user font height or width change from causing potential out-of-bounds access
vt: defer kfree() of vc_screenbuf in vc_do_resize()
The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:
nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The race condition may happen if the UART reference clock is shared with
some other device (on Baikal-T1 SoC it's another DW UART port). In this
case if that device changes the clock rate while serial console is using
it the DW 8250 UART port might not only end up with an invalid uartclk
value saved, but may also experience a distorted output data since
baud-clock could have been changed. In order to fix this lets at least
try to adjust the 8250 port setting like UART clock rate in case if the
reference clock rate change is discovered. The driver will call the new
method to update 8250 UART port clock rate settings. It's done by means of
the clock event notifier registered at the port startup and unregistered
in the shutdown callback method.
Note 1. In order to avoid deadlocks we had to execute the UART port update
method in a dedicated deferred work. This is due to (in my opinion
redundant) the clock update implemented in the dw8250_set_termios()
method.
Note 2. Before the ref clock is manually changed by the custom
set_termios() function we swap the port uartclk value with new rate
adjusted to be suitable for the requested baud. It is necessary in
order to effectively disable a functionality of the ref clock events
handler for the current UART port, since uartclk update will be done
a bit further in the generic serial8250_do_set_termios() function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms can be designed in a way so the UART port reference clock
might be asynchronously changed at some point. In Baikal-T1 SoC this may
happen due to the reference clock being shared between two UART ports, on
the Allwinner SoC the reference clock is derived from the CPU clock, so
any CPU frequency change should get to be known/reflected by/in the UART
controller as well. But it's not enough to just update the
uart_port->uartclk field of the corresponding UART port, the 8250
controller reference clock divisor should be altered so to preserve
current baud rate setting. All of these things is done in a coherent
way by calling the serial8250_update_uartclk() method provided in this
patch. Though note that it isn't supposed to be called from within the
UART port callbacks because the locks using to the protect the UART port
data are already taken in there.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1
With GPIOs preconfigured as per commit 7dea8165f1 all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064e ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com
Fixes: 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250 port")
Reported-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: stable <stable@vger.kernel.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200718123840.19957-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull tty/serial driver updates from Greg KH:
"Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
All of these have been in linux-next with no issues for a while"
* tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (67 commits)
tty: serial: qcom_geni_serial: Add 51.2MHz frequency support
tty: serial: imx: clear Ageing Timer Interrupt in handler
serial: 8250_fintek: Add F81966 Support
sc16is7xx: Add flag to activate IrDA mode
dt-bindings: sc16is7xx: Add flag to activate IrDA mode
serial: 8250: Support rs485 bus termination GPIO
serial: 8520_port: Fix function param documentation
dt-bindings: serial: Add binding for rs485 bus termination GPIO
vt: keyboard: avoid signed integer overflow in k_ascii
serial: 8250: Enable 16550A variants by default on non-x86
tty: hvc_console, fix crashes on parallel open/close
serial: imx: Initialize lock for non-registered console
sc16is7xx: Read the LSR register for basic device presence check
sc16is7xx: Allow sharing the IRQ line
sc16is7xx: Use threaded IRQ
sc16is7xx: Always use falling edge IRQ
tty: n_gsm: Fix bogus i++ in gsm_data_kick
tty: n_gsm: Remove unnecessary test in gsm_print_packet()
serial: stm32: add no_console_suspend support
tty: serial: fsl_lpuart: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
...
Commit e8759ad17d ("serial: uapi: Add support for bus termination")
introduced the ability to enable rs485 bus termination from user space.
So far the feature is only used by a single driver, 8250_exar.c, using a
hardcoded GPIO pin specific to Siemens IOT2040 products.
Provide for a more generic solution by allowing specification of an
rs485 bus termination GPIO pin in the device tree: Amend the serial
core to retrieve the GPIO from the device tree (or ACPI table) and amend
the default ->rs485_config() callback for 8250 drivers to change the
GPIO on request from user space.
Perhaps 8250_exar.c can be converted to the generic approach in a
follow-up patch.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/94c6c800d1ca9fa04766dd1d43a8272c5ad4bedd.1589811297.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standard 8250 UART ports are designed in a way so they can communicate
with baud rates up to 1/16 of a reference frequency. It's expected from
most of the currently supported UART controllers. That's why the former
version of serial8250_get_baud_rate() method called uart_get_baud_rate()
with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX)
and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like
it was suggested in commit ("serial: 8250_mtk: support big baud rate."),
caused acceptance of bauds, which was higher than the normal UART
controllers actually supported. As a result if some user-space program
requested to set a baud greater than (uartclk / 16) it would have been
permitted without truncation, but then serial8250_get_divisor(baud)
(which calls uart_get_divisor() to get the reference clock divisor) would
have returned a zero divisor. Setting zero divisor will cause an
unpredictable effect varying from chip to chip. In case of DW APB UART the
communications just stop.
Lets fix this problem by getting back the limitation of (uartclk +
tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek
8250 UART ports driver developer shouldn't have touched it in the first
place notably seeing he already provided a custom version of set_termios()
callback in that glue-driver which took into account the extended baud
rate values and accordingly updated the standard and vendor-specific
divisor latch registers anyway.
Fixes: 81bb549fdf ("serial: 8250_mtk: support big baud rate.")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Long Cheng <long.cheng@mediatek.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/20200506233136.11842-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're about to amend uart_get_rs485_mode() to support a GPIO pin for
rs485 bus termination. Retrieving the GPIO descriptor may fail, so
allow uart_get_rs485_mode() to return an errno and change all callers
to check for failure.
The GPIO descriptor is going to be stored in struct uart_port. Pass
that struct to uart_get_rs485_mode() in lieu of a struct device and
struct serial_rs485, both of which are directly accessible from struct
uart_port.
A few drivers call uart_get_rs485_mode() before setting the struct
device pointer in struct uart_port. Shuffle those calls around where
necessary.
[Heiko Stuebner did the ar933x_uart.c portion, hence his Signed-off-by.]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/271e814af4b0db3bffbbb74abf2b46b75add4516.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit 835d844d1a ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a.
Fixes: 835d844d1a ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
