If register_netdev() fails now, then we call mutex_unlock(&bnad->conf_mutex);
on the error path, but it's already unlocked. So we acquire the lock in error
path which will be later unlocked after the cleanup.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We check ether_type before registering the platform device in
arch/m68k/mac/config.c. Doing the same test again in the driver is
redundant so remove it.
Multiple probes should not happen since the conversion to platform devices,
so lose that test too.
Then macmace.c need not include macintosh.h, so remove that and irq.h and
include linux/interrupt.h explicitly.
Tested on PowerBook 520, Quadra 660av, LC 630.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMSC911X_USE_16BIT needs to be set when using 16-bit register
access. However, currently no flag is set if the device tree
doesn't specify 32-bit access, resulting in a BUG() and a non-
working driver when 16-bit register access is configured for
smsc911x in the DT.
This patch should set the SMSC911X_USE_16BIT flag in a manner
consistent with the documented DT bindings.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
o A performance drop was seen with firmware loaded
from flash. This workaround fixes it.
o Updated driver version to 4.0.77
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using the multi_tx_table to map possible Tx queues to Tx rings
we can just do simple subtraction for the unlikely event that the Tx queue
provided exceeds the number of Tx rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since igb only uses advanced descriptors we might as well just use an IGB
specific define and drop the _ADV suffix for the descriptor declarations.
In addition this can be further reduced by assuming that it will be working
on pointers since that is normally how the Tx descriptors are handled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many of the function names in the hot path are carrying an extra "_adv"
suffix on the end of them to represent the fact that they are using
advanced descriptors instead of legacy descriptors. However since all igb
uses are advanced descriptors adding the extra suffix doesn't really add
any additional data. Since this is the case it is easiest to just drop the
suffix and save us from having to store the extra characters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to be a general cleanup and performance improvement
for clean_rx_irq. The previous patch should have updated the allocation so
that the rings can be treated as read-only within the clean_rx_irq
function. In addition I am re-ordering the operations such that several
goals are accomplished including reducing the overhead for packet
accounting, reducing the number of items on the stack, and improving
overall performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve performance by splitting the Tx and Rx
rings into 3 sections. The first is primarily a read only section
containing basic things like the indexes, a pointer to the dev and netdev
structures, and basic information. The second section contains the stats
and next_to_use and next_to_clean values. The third section is primarily
unused values that can just be placed at the end of the ring and are not
used in the hot path.
The adapter structure has several sections that are read in the hot path.
In order to improve performance there I am combining the frequent read
hot path items into a single cache line.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to streamline the Rx buffer allocation and cleanup.
This is accomplished by reducing the number of writes by only having the Rx
descriptor ring written by software during allocation, and it will only be
read during cleanup.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes support for single buffer mode from igb and makes the
driver function in packet split always. The advantage to doing this is
that we can reduce total memory allocation overhead significantly as we
will only need to allocate one 1K slab per packet and then make use of a
reusable half page instead of allocating a 2K slab per packet.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the max_frame_size in order account for an optional
VLAN tag. In order to support this we must also increase the
MAX_STD_JUMBO_FRAME_SIZE to account for the 4 extra bytes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the RXDCTL and TXDCTL configurations and optimizes RX
performance by allowing back write-backs on all hardware other than 82576.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change details:
- In a continuous sequence of ifconfig up/down operations, there is a small
window of race between bnad_set_rx_mode() and bnad_cleanup_rx() while the
former tries to access rx_info->rx & the latter sets it to NULL. This race
could lead to bna_rx_mode_set() being called with a NULL (rx_info->rx)
pointer and a crash.
- Hold bnad->bna_lock while setting / unsetting rx_info->rx in bnad_setup_rx()
& bnad_cleanup_rx(), thereby eliminating the race described above.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Rx queue size is changed, queues are torn down and setup with the new queue
size. During this operation, clear promiscuous mode and restore the original
VLAN filter.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a BUG_ON() as it is not required.
Change the unconditional write to release a semaphore to read sem first
and then write. This will eliminate the possibility of sem getting locked
while trying to release it in case if previous sem_get operation failed.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_start_all_queues() is already called in ixgbe_up_complete, no need
to do it twice.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove duplicate inc of hwstats->ruc
Introduce separate loops for 8 and 16 register reads.
Consolidate mac checks under one case.
Make sure registers are cleared on read.
Reported-by: Jonathan Lynch <jonathan.lynch@thenowfactory.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
CC: Jonathan Lynch <jonathan.lynch@thenowfactory.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch improves the memory utilization with RSC when in one-buffer
mode. This is accomplished by making the default buffer sizes match up
with the standard memory allocation sizes minus 1K for shared info and
padding overhead. By doing this CPU utilization when doing large receives
can be reduced by as much as 8%.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The adapter structure was removed from the call so it can be dropped from
the ixgbe_fso documentation.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the 82598 phys was not being correctly identified as being SFP.
This change corrects that.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds a small bit of missing code for enabling the overheat sensor
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_up and ixgbe_up_complete will always return 0. Since this doesn't
provide any useful information we might as well just make them both void
and save ourselves from having to return an unused value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes an issue in which the incorrect amount of headroom was
being reserved for flow director filters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes a minor redundancy in that tx_sample_rate was set twice.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Private rx_csum flags are now duplicate of netdev->features & NETIF_F_RXCSUM.
Removing this needs deeper surgery.
Things noticed:
- ixgb has RX csum disabled by default
- HW VLAN acceleration probably can be toggled, but it's left as is
- the resets on RX csum offload change can probably be avoided
- there is A LOT of copy-and-pasted code here
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A user-space process must use ETHTOOL_GRXCLSRLCNT to find the number
of classification rules, then allocate a buffer of the right size,
then use ETHTOOL_GRXCLSRLALL to fill the buffer. If some other
process inserts or deletes a rule between those two operations,
the user buffer might turn out to be the wrong size.
If it's too small, the return value will be -EMSGSIZE. But if it's
too large, there is no indication of this. Fix this by updating
the rule_cnt field on return.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.
Add note that drivers must not use ethtool_rxnfc::rule_locs.
The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All tables of function pointers should be const.
The pre-existing code has lots of needless indirection...
Inspired by similar change in PAX.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent malicious usage, all tables of pointers must be const.
Compile tested only.
Gleaned for PAX.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function tables need to be const to prevent malicious use.
This is compile tested only.
Gleaned from PAX.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier developer misunderstood the meaning of the 'irq' fields and
the driver did not support the standard fields. To avoid invalidating
existing user documentation, we report and accept changes through
either the standard or 'irq' fields. If both are changed at the same
time, we prefer the standard field.
Also explain why we don't currently use the 'max_frames' fields.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a range check, and move the check that RX and TX are consistent
from efx_ethtool_set_coalesce().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reported TX IRQ moderation is generated in a completely crazy way.
Make it simple and correct.
When channels are shared between RX and TX, TX IRQ moderation must be
the same as RX IRQ moderation, but must be specified as 0! Allow it
to be either specified as the same, or left at its previous value
in which case it will be quietly overridden.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible to inadvertently add additional interrupt causes to the
MSI-X other interrupt. This occurred when things such as RX buffer overrun
events were being triggered at the same time as an event such as a Flow
Director table reinit request. In order to avoid this we should be
explicitly programming only the interrupts that we want enabled. In
addition I am renaming the ixgbe_msix_lsc function and interrupt to drop
any implied meaning of this being a link status only interrupt.
Unfortunately the patch is a bit ugly due to the fact that ixgbe_irq_enable
needed to be moved up before ixgbe_msix_other in order to have things
defined in the correct order.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to cleanup some of the code related to SR-IOV and the
interrupt registers. Specifically I am moving the EITRSEL configuration
into the MSI-X configuration section instead of enablement. Also I am
fixing the VF shutdown path since it had operations in the incorrect order.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The reset paths are overly complicated and are either missing steps or
contain extra unnecessary steps such as reading MAC address twice. This
change is meant to help clean up the reset paths an get things functioning
correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updated the TXDCTL configuration. The main goal is to be much
more explicit about the configuration and avoid a possible fake TX hang
when the interrupt throttle rate is set to 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a minor whitespace cleanup to compress the device ID
declaration and board type declaration onto the same line. It seems to
make sense since all of the combinations of the two are less than 80
characters and it makes the overall layout a bit more readable.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch drops a set of unnecessary dereferences to the hardware structure
since we already have a local copy of the hardware pointer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that the map_rings_to_vectors call will work with
all interrupt types. The advantage to this is that there will now be a
predictable mapping for all given interrupt types.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change switches us over to using the ring->dev pointer instead of
having to use the adapter->pdev->dev reference. The advantage to this is
that it is a much shorter route to get the to final needed value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The allocation and freeing of the IRQ affinity hint needs some updates
since there are a number of spots where we run into possible issues with
the hint not being correctly updated.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change consolidates all of the MSI-X interrupt and polling routines
into two single functions. One for the interrupt and one for the code.
The main advantage to doing this is that the compiler can optimize the
routines into single monolithic functions which should allow all of them
function to occupy a single block of memory and as such avoid jumping
around.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the default Tx work limit is 256 buffers or
1/2 of an entire ring instead of a full ring size so that it is much more
likely that we will be able to actually reach the work limit value.
Previously with the value set to an entire ring it would not have been
possible for us to trigger an event due to the fact that the Tx work is
stopped at the point where we cannot place one more buffer on the ring and
it is not restarted until cleanup is complete.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch just moves some code around for better organization.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the implementatino of tg3_halt_cpu() earlier in the
file to eliminate its prototype.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the implementation of tg3_write_sig_post_reset()
earlier to eliminate its prototype.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves tg3_stop_fw() earlier in the file to eliminate its
prototype.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In older devices, 1-shot MSI mode had to be enabled by the code. In
newer devices however, 1-shot MSI mode is enabled by default; code would
be needed to disable it.
Disabling 1-shot MSI mode is useful when debugging. This patch changes
the code so that the TG3_FLAG_1SHOT_MSI accurately reflects (and
controls) the state of 1-shot MSI mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the tp->rx_offset term if NET_IP_ALIGN is defined to
zero.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a minor counter initialization bug and makes the MSI
workaround slightly more efficient by attempting to service pending
interrupts before applying the workaround.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sure the driver checks all advertisement bits when
checking the current hw advertisements.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New GMAC chips have an extra register to indicate
the presence of the optional features/functions of
the DMA core.
This patch adds this support and all the HW cap
are exported via debugfs.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Synopsys ID is now passed from the MAC core
to the main. This info will be used for managing
the HW cap register (supported in the new GMAC
generations).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the following debugFs entry to dump the
RX/TX DMA rings:
/sys/kernel/debug/stmmaceth/descriptors_status
This is an example:
=======================
RX descriptor ring
=======================
[0] DES0=0x85ee0320 DES1=0x1fff1fff BUF1=0x5fae2022 BUF2=0x0
[1] DES0=0x85ee0320 DES1=0x1fff1fff BUF1=0x5fae0022 BUF2=0x0
[2] DES0=0x81460320 DES1=0x1fff1fff BUF1=0x5f9dd022 BUF2=0x0
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the MMC management counters support.
MMC module is an extension of the register address
space and all the hardware counters can be accessed
via ethtoo -S ethX.
Note that, the MMC interrupts remain masked and the logic
to handle this kind of interrupt will be added later (if
actually useful).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms e.g. SPEAr the wake up irq differs from the
GMAC interrupt source.
With this patch an external wake up irq can be passed through the
platform code and named as "eth_wake_irq".
In case the wake up interrupt is not passed from the platform
so the driver will continue to use the mac irq (ndev->irq)
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DWMAC Management Counters (MMC) are not fully support.
The minimal support added in the past allowed to
only disable counters (if present) and mask their
interrupts.
This patch prepares the driver to support the MMC
removing obsolete code.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a piece of code (actually commented)
only useful for some ST platforms in the past.
This kind of setting now can be done by using the platform
callbacks provided in linux/stmmac.h (see the stmmac.txt for
further details).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Found a leak in sk_buff unmapping of PCI dma addresses where boundary
conditions are not properly handled in freeing all Tx buffers. Freeing
of all Tx buffers is done considering sk_buffs data and fragments can
be mapped at the boundary.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_buff unmap_array grows greater than 65536 (x2) with Tx ring of 65536.
Reducing TXQ depth and safe(max) acking of Tx events to 32768 (same as Rx).
Add defines for TX and RX queue depths.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Check the BNAD_RF_MBOX_IRQ_DISABLED flag after acquiring the bna_lock,
since checking the flag and executing bna_mbox_handler needs to be atomic.
If not, it opens up window where flag is reset when it was checked, but got
set while spinning on the lock by the other thread which is actually
holding the lock
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Async mode of Tx/Rx queue initialization in BNAD from a task queue context
runs into non-unique taskq allocation issues. Get rid of Tx/Rx
initialization from task q context
- In the attach function, wait for IOC enable, then do Tx/Rx queue
initialization. Default BNA attributes are used when IOC enable from attach
fails and values are set to:
1 TxQ, 1 RxQ, 1 Unicast MAC, 1 RIT entry
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Add tx_skb counters and NAPI debug counters to ethtool stats.
- Add rlb stats strings to bnad_net_stats_strings{} array. rlb_stats field
was added to struct bfi_enet_stats {} but the corresponding name structure
array for ethtool was not initialized with right strings, even though the
actual name structure array got expanded. This caused a NULL pointer
violation and a crash when doing ehtool -S <if_name>.
- Modify dim timer stop logic to make it dependent on cfg and run flags
- While setting the ring parameter restore the rx, vlan configuration and
set rx mode
- Indentation fix
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Initialize rx_id to 0 for bnad_cleanup_rx
- Return -ENOMEM in case if bna_rx_create fails
- Count the Rx buffer allocation failures in bnad_alloc_n_post_rxbufs()
- Remove unnecessary initialization of using_dac to false in bnad_pci_probe
- Release lock if error while doing bna_num_txq_set in bnad_pci_probe
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Print log messages when running with reduced number of MSI-X vectors
and when defaulting to INTx mode.
- Remove BUG_ONs and header file inclusion that are not needed
- Comments addition/cleanup
- Unused code cleanup
- Add New Line to Print msg in bfa_sm_fault
- Formatting fix
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Add bnad_pci_unmap_skb() API to unmap skb from transmit path and update the
unmap index. Add more checks for illegal skbs in transmit path. Add tx_skb
counters for dropped skbs.
- The unmap_cons index used in bnad_free_txbufs() is incorrectly declared as
u16. It quickly wraps around and accesses null sk_buff ptr. So using u32 to
handle unmap_array.
- Disable and enable interrupts from the same polling context to prevent
reordering in Rx path.
- Add Rx NAPI debug counters.
- Make NAPI budget check more generic.
- Modify dim timer stop logic to make it dependent on cfg and run flags
- Handle reduced MSI-X vectors case in bnad_enable_msix.
- Check for single frame TSO skbs and send them out as non-TSO.
- Put memory barrier after bna_txq_prod_indx_doorbell().
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Remove unnecessary ccb check from bnad_poll_cq
- Add bnad pointer to rx_ctrl structure, so that bnad can be accessed directly
from rx_ctrl in the NAPI poll routines, even if ccb is NULL
- Validate ccb before referencing to it in bnad_msix_rx and bnad_napi_poll_rx
- Fix the order of NAPI init / uninit in Tx / Rx setup / teardown path:
a. Kill bnad tx free tasklet ahead of call to bna_tx_destroy()
b. Call NAPI disable only after call to Rx free_irq(). This makes sure Rx
interrupt does not schedule a poll when NAPI is already disabled
- NAPI poll runs before the h/w has completed configuration. This causes a
crash. Delay enabling NAPI till after bna_rx_enable(). Split NAPI
initialization into 2 steps, bnad_napi_init() & bnad_napi_enable().
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Return error as -EIO if bnad_res_alloc fails
- Release the configuration lock before registering with net_device layer.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Naming changes: rename devid, BNAD_MAX_TXS, BNAD_MAX_RXS,
BNAD_MAX_RXPS_PER_RX to device, BNAD_MAX_TX, BNAD_MAX_RX,
BNAD_MAX_RXP_PER_RX respectively and change all the references.
Macro Fix: Add ioc_isr_mod_set check to bfa_nw_ioc_mbox_regisr macro
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Santiago Leon <santil@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid long lines also use phys_to_virt(page_to_phys(page)) =>
page_address(page) (since the are effectively the same thing for lowmem pages).
Also dump the frag's size instead of the headlen when dumping a frag.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Roopa Prabhu <roprabhu@cisco.com>
Cc: David Wang <dwang2@cisco.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Rasesh Mody <rmody@brocade.com>
Cc: Debashis Dutt <ddutt@brocade.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: linux-acenic@sunsite.dk
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
On Mon, 2011-08-29 at 13:28 -0700, Randy Dunlap wrote:
> (on i386 or x86_64)
>
> drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:10148: error: 'bnx2x_fcoe_get_wwn' undeclared here (not in a function)
This should sync #define structures between definition and declaration
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beacon test flashes both port LEDs instead of just 1 LED of a port.
Updated driver version to 5.0.23.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading CRB registers(if reqd) before releasing the api lock.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FLT entry for FW image region has changed for C0 cards.
Updated the driver to look at the right region in the FLT.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added more debug messages while loopback test in progress
Signed-off-by: Manish chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RNBC (0x03FC0) is only for 82598 and has different meaning
on newer HW. Make sure to only clear it for 82598.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting advertised speed/duplex with ethtool.
Also cleaned up the comment since we also support 100/F.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A logic error in ixgbe_fc_autoneg_fiber() that treated a masked u32 as a
boolean would make it so we would never fall hit a error check case. So
now I force the u32 to a boolean value with '!!'.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I'm removing NETIF_F_GRO from being initialed in the feature flags during
ixgbe_probe() bases on a comment from Michal Miroslaw
<mirq-linux@rere.qmqm.pl> that it is always set by network code now.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X540 devices do not clear PFC before sets. This results in
the device possibly responding to PFC frames that the user
has disabled. Although it would also be wrong for the peer
to be transmitting these frames. Now we clear the register
before set.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This consolidates setup code for multiple traffic classes in
the setup_tc routine.
Prep work to allow IEEE DCBX to optimize for number of traffic
classes. Also simplifies code paths.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The packet buffer is correctly allocated by generic pb allocation
path in ixgbe_configure() there is no need to do the allocation
here as well.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
One existing call sites still expect either 4 or 8 traffic
classes to be specified. This fixes this allowing arbitrary
values up to 8 to work as expected.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to fix the patch:
ixgbe: Cleanup FCOE and VLAN handling in xmit_frame_ring
And can be rolled into it if needed.
What this fixes is that VLAN tagged packets were not being tagged if they
were prio 7 which matches up with TC_PRIO_CONTROL. In order to fix it I am
just setting things up so that we always tag VLAN tagged packets.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the CC bit in the descriptor is set when
SR-IOV is enabled. This is needed in order to support offloading
functionality when passing traffic over the internal TX switch.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the bnx2x device has encountered parity errors, the chip will not DMA
any replies. Using wait_event_timeout() will allow us to make forward
progress and let bnx2x reset the chip.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase it to NVRAM configured limit or 1024 whichever is less.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.
This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers. In
addition, by enabling all the new Kconfig options does not add
any un-expected options.
CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change converts the current bit array into a linked list so that the
q_vectors can simply go through ring by ring and locate each ring needing
to be cleaned.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch helps to simplify the work being done by the transmit path by
removing the unnecessary compares between count and the work limit. Instead
we can simplify this by just adding a budget value that will act as a count
down from the work limit value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Private rx_csum flags are now duplicate of netdev->features & NETIF_F_RXCSUM.
Removing this needs deeper surgery.
Since ixgbevf doesn't change hardware state on RX csum enable/disable
its reset is avoided.
Things noticed:
- HW VLAN acceleration probably can be toggled, but it's left as is
- the resets on RX csum offload change can probably be avoided
- there is A LOT of copy-and-pasted code here
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Compute statistics per ring using 64 bits, and provide
network device stats in 64 bits.
It should make this driver multiqueue operations faster (no more cache
line ping pongs on netdev->stats structure)
Use u64_stats_sync infrastructure so that its safe on 32bit arches as
well.
Based on a prior patch from Stephen Hemminger
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a chance that between the time EOP is read and the time it is
used another transmit on a different CPU could have run and completed,
thus leaving EOP in a bad state.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Private rx_csum flags are now duplicate of netdev->features &
NETIF_F_RXCSUM. Remove those duplicates and use the net_device_ops
ndo_set_features. This is based on the original patch submitted by
Michał Mirosław <mirq-linux@rere.qmqm.pl>
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Virtual Machines with emulated e1000 network adapter running on Parallels'
server were seeing kernel panics due to the e1000 driver dereferencing an
unexpected NULL pointer retrieved from buffer_info->skb.
The problem has been addressed for the e1000e driver, but not for the e1000.
Since the two drivers share similar code in the affected area, a port of the
following e1000e driver commit solves the issue for the e1000 driver:
commit 9ed318d546
Author: Tom Herbert <therbert@google.com>
Date: Wed May 5 14:02:27 2010 +0000
e1000e: save skb counts in TX to avoid cache misses
In e1000_tx_map, precompute number of segements and bytecounts which
are derived from fields in skb; these are stored in buffer_info. When
cleaning tx in e1000_clean_tx_irq use the values in the associated
buffer_info for statistics counting, this eliminates cache misses
on skb fields.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rspq->rsphdlr[] array has BFI_MC_MAX elements, so this test was
off by one.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduced a new lock here, so there was error path which needs
an unlock now.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54616 PHY is very similar to the 54618SE, only without EEE support, which will not be activated due to querying the actual PHY type.
This check is already done by reading a dedicated PHY register.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x used to be able to set rxhash, but this was lost in the conversion
to hw_features (commit 66371c441).
Restore it and enable it by default.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
CC: Vladislav Zolotarov <vladz@broadcom.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Dmitry Kravkov <dmitry@broadcom.com>
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Flashing some of the PHYs can take longer thus increasing the total flash
update time to a max of 40s.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_drops_no_frags HW counter for RSS rings is 16bits in HW and can
wraparound often. Maintain a 32-bit accumulator in the driver to prevent
frequent wraparound.
Also, incorporated Eric's feedback to use ACCESS_ONCE() for the accumulator
write.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of adapter->pcicfg and its use. Use pci_config_read/write_dword()
instead.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possibility of be_post_rx_frags() being called simultaneously from
both be_worker() (when rx_post_starved) and be_poll_rx() (when rxq->used is 0).
This can be avoided by posting rx buffers only when some completions have been
reaped.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows to get driver specific debug messages output
providing a module parameter. As far as the maximum level of verbosity
is too high, it is demoted by default.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.120.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds external loopback support to tg3's ethtool selftest.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_test_loopback() function is starting to get more complicated as
more loopback tests are added. This patch cleans up the code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pulls out the internal phy loopback setup code into a
separate function. This cleans up the loopback test code and makes it
available for NETIF_F_LOOPBACK support later.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver puts the device into MAC loopback in two places in the
driver. This patch consolidates the code into a single routine.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that CPMU devices don't do MAC loopback, all the CPMU power saving
mode adjustments are unneeded. This patch removes the dead code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to further cleanup the transmit path by streamlining
some of the VLAN and FCOE/DCB tasks in the transmit path. In addition it
adds code for support software VLANs in the event that they are used in
conjunction with DCB and/or FCOE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CONFIG_FCOE is not the correct define to check since it is possible for it
to be CONFIG_FCOE_MODULE, as such the reference to it should be replaced
with IXGBE_FCOE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements a partial refactor of the TX map/queue and cleanup
routines. It merges the map and queue functionality and as a result
improves the transmit performance by avoiding unnecessary reads from memory.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the error message in the last DDP user buffer to warn_once
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some features currently not supported by the driver (e.g. RSS) require the
use of extended descriptors, but the driver is setup to only use legacy
descriptors in all modes except for when jumbo frames are enabled on some
parts. Convert the driver to always use extended descriptors in order to
enable the forthcoming support of these other features.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are valid configurations where Max BW is configured to zero for
some VNs.
Print the message only if debugging is enabled and do not call the
configuration "illegal".
[v2: use DP(), not BNX2X_DBG_ERR(); recommended by Eilon Greenstein.]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9aa3283595 (ehea/ibm*: Move the
IBM drivers) the IBM_NEW_EMAC* were renames to IBM_EMAC*
The conversion was incomplete so that even if the driver was added to
the .config it wasn't built, but there were no errors). In this commit
we also update the various defconfigs that use EMAC to use the new
Kconfig symbol, and explicitly add the NET_VENDOR_IBM guard.
We do not explicitly select the Kconfig dependencies, as this would force
EMAC on. Doing it in the defconfig allows more flexibility.
Tested on a canyondlands board.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Korina.c is a MIPS-specific SOC driver and <asm/segment> is empty on
MIPS since 2.1.7 ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use IFF_UNICAST_FTL to find out if driver handles unicast address
filtering. In case it does not, promisc mode is entered.
Patch also fixes following drivers:
stmmac, niu: support uc filtering and yet it propagated
ndo_set_multicast_list
bna, benet, pxa168_eth, ks8851, ks8851_mll, ksz884x : has set
ndo_set_rx_mode but do not support uc filtering
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pr_fmt(fmt) KBUILD_MODNAME ": " to prefix messages with "bnx2x: ".
Remove #define DP_LEVEL and use pr_notice.
Repeating KERN_<LEVEL> isn't necessary in multi-line printks.
printk macro neatening, use fmt and ##__VA_ARGS__.
Coalesce long formats.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uses of pr_cont should be avoided where reasonably possible
because they can be interleaved by other threads and processes.
Coalesce pr_cont uses.
Fix typos, duplicated words and spacing in DP uses caused
by split multi-line formats. Coalesce some of these
split formats. Add missing terminating newlines to DP uses.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %pM and mac address directly instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since sungem_phy is used by multiple, unrelated, drivers make it
build as a real module under drivers/net.
depmod will pick up the symbol dependency and make sure sungem_phy.ko
gets loaded any time sungem.ko or spider_net.ko is loaded.
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes build failures of the spider_net driver because it tries
to use a convoluted path to include this header.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the move of the Ethernet drivers into drivers/net/ethernet/
there was some leftover cleanup to do in the Kconfig and Makefile.
Removed the 10/100, 1000, and 10GbE Kconfig menus.
Removed the out-dated pci-skeleton.c file which was used an
example driver. With the current networking features and
structure, the file is no longer a good example to use for
driver creation.
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on feedback from Alan Cox, the acenic driver moved to
drivers/net/ethernet/alteon/ and made the necessary Kconfig and
Makefile changes.
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Tilera driver into drivers/net/ethernet/tile and
make the necessary Kconfig and Makefile changes.
Updated the Kconfig so that the options defualt to y if TILE kernel.
CC: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Xircom driver into drivers/net/ethernet/xircom/ and
make the necessary Kconfig and Makefile changes.
CC: <psheer@icon.co.za>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Renesas driver into drivers/net/ethernet/renesas/ and make
the necessary Kconfig and Makefile changes.
CC: Yoshihiro Shimoda <yoshihiro.shirmoda.uh@renesas.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the netx driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.
CC: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the Davicom driver into drivers/net/ethernet/davicom/ and
make the necessary Kconfig and Makefile changes.
CC: Ben Dooks <ben@simtec.co.uk>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the Microchip driver into drivers/net/ethernet/microchip/ and
make the necessary Kconfig and Makefile changes.
CC: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Aeroflex Gaisler driver into drivers/net/ethernet/aeroflex/
and make the necessary Kconfig and Makefile changes.
CC: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Avionic driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.
CC: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Dave Ethernet driver into drivers/net/ethernet/ and
make the necessary Kconfig and Makefile changes.
CC: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the HP driver into drivers/net/ethernet/hp/ and
made the necessary Kconfig and Makefile changes.
CC: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Adaptec driver into drivers/net/ethernet/adaptec/ and make
the necessary Kconfig and Makefile changes.
CC: Ion Badulescu <ionut@badula.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the nForce driver into drivers/net/ethernet/nvidia/ and make
the necessary Kconfig and Makefile changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Myson driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.
CC: Donald Becker <becker@scyld.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the RDC driver into drivers/net/ethernet/rdc/ and make the
necessary Kconfig and Makefile changes.
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Atmel driver into drivers/net/ethernet/cadence/ and
make the necessary Kconfig and Makefile changes.
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Move the Analog Devices Inc driver into drivers/net/ethernet/adi/ and
make the necessary Kconfig and Makefile changes.
CC: <uclinux-dist-devel@blackfin.uclinux.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Bob Liu <bob.liu@analog.com>
Move the Lantiq driver into drivers/net/ethernet/ and the
necessary Kconfig and Makefile changes.
CC: John Crispin <blogic@openwrt.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: John Crispin <blogic@openwrt.org>
Move the MIPS drivers into drivers/net/ethernet/ and
make the necessary Kconfig and Makefile changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the IDT driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes
CC: "IDT Inc." <rischelp@idt.com>
CC: Felix Fietkau <nbd@openwrt.org>
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the IC Plus driver into drivers/net/ethernet/icplus/ and
make the necessary Kconfig and Makefile changes.
CC: <craig_rich@sundanceti.com>
CC: <sorbica@icplus.com.tw>
CC: <jesse@icplus.com.tw>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Xilinx drivers into drivers/net/ethernet/xilinx/ and
make the necessary Kconfig and Makefile changes.
CC: John Williams <john.williams@petalogix.com>
CC: "David H. Lynch Jr." <dhlii@dlasys.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the JME driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Cavium driver to drivers/net/ethernet/octeon/ and
make the necessary Kconfig and Makefile changes.
CC: David Daney <david.daney@cavium.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: David Daney <david.daney@cavium.com>
Move the packet engine drivers to drivers/net/ethernet/packetengines/
and the necessary Kconfig and Makefile changes.
CC: Donald Becker <becker@scyld.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the s6gmac driver to drivers/net/ethernet/ and
make the necessary Kconfig and Makefile changes.
CC: Oskar Schirmer <os@emlix.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Tundra driver to drivers/net/ethernet/tundra/ and
make the necessary Kocnfig and Makefile changes.
CC: Kong Lai <kong.lai@tundra.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Nuvoton driver into drivers/net/ethernet/nuvoton/ and
make the necessary Kconfig and Makefile changes.
CC: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Cirrus Ethernet driver into drivers/net/ethernet/cirrus/
and make the necessary Kconfig and Makefile changes
CC: Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the SiS drivers into drivers/net/ethernet/sis/ and make the
necessary Kconfig and Makefile changes
CC: Daniele Venzano <venza@brownhat.org>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Error comes from commit ac124ff973
(be2net: cleanup and refactor stats code)
ERROR: "__udivdi3" [drivers/net/benet/be2net.ko] undefined!
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Toshiba ethernet drivers into drivers/net/ethernet/toshiba
and make the necessary Kconfig and Makefile changes.
CC: Geoff Levand <geoff@infradead.org>
CC: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
CC: Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Micrel drivers into drivers/net/ethernet/micrel/ and
make the necessary Kconfig and Makefile changes.
CC: Ben Dooks <ben@simtec.co.uk>
CC: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Allied Telesis/Fujitsu drivers into drivers/net/ethernet/fujitsu/
and make the necessary Kconfig and Makefile changes.
CC: Shingo Fujimoto <shingo@flab.fujitsu.co.jp>
CC: Yutaka Tamiya <tamy@flab.fujitsu.co.jp>
CC: Rene Schmit <rene@bss.lu>
CC: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the VIA drivers into drivers/net/ethernet/via/ and make the
necessary Kconfig and Makefile changes.
CC: Roger Luethi <rl@hellgate.ch>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Marvell Ethernet drivers into drivers/net/ethernet/marvell/
and make the necessary Kconfig and Makefile changes.
CC: Sachin Sanap <ssanap@marvell.com>
CC: Zhangfei Gao <zgao6@marvell.com>
CC: Philip Rakity <prakity@marvell.com>
CC: Mark Brown <markb@marvell.com>
CC: Lennert Buytenhek <buytenh@marvell.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the OKI Semiconductor driver into driver/net/ethernet/oki-semi/
and make the necessary Kconfig and Makefile changes.
Note: there is no documented maintainer for this driver, so I CC'd
the last 2 major contributors.
CC: Tomoya <tomoya-linux@dsn.okisemi.com>
CC: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the drivers that use SEEQ chipset into drivers/net/ethernet/seeq
and make the necessary Kconfig and Makefile changes.
CC: Russell King <linux@arm.linux.org.uk>
CC: Hamish Coleman <hamish@zot.apana.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the SGI drivers into drivers/net/ethernet/sgi/ and make the
necessary Kconfig and Makefile changes.
CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the DEC - Tulip driver into drivers/net/ethernet/dec/tulip/
and make the necessary Kconfig and Makefile changes.
The Digital Equioment (DEC) driver ewrk3 was moved into
drivers/net/ethernet/dec/ and the remaining drivers (Tulip)
were moved into drivers/net/ethernet/dec/tulip/
CC: Tobias Ringstrom <tori@unhappy.mine.nu>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: David Davies <davies@maniac.ultranet.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Both Spider net driver and Sun GEM driver use the sungem_phy.o object.
This fix creates a Kconfig object for sungem_phy (like MDIO) so that
both drivers require the SUNGEM_PHY object.
This has been compile tested for the Sun GEM driver.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Atheros drivers into drivers/net/ethernet/atheros/ and
make the necessary Kconfig and Makefile changes.
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the D-Link drivers into drivers/net/ethernet/dlink/ and
make the necessary Kconfig and Makefile changes.
CC: Bjorn Ekwall <bj0rn@blox.se>
CC: Donald Becker <becker@scyld.com>
CC: Edward Peng <edward_peng@dlink.com.tw>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Realtek drivers into drivers/net/ethernet/realtek/ and make
the necessary Kconfig and Makefile changes.
CC: Realtek linux nic maintainers <nic_swsd@realtek.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
CC: Jeff Garzik <jgarzik@pobox.com>
CC: Donald Becker <becker@scyld.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Faraday driver into drivers/net/ethernet/faraday/ and
make the necessary Kconfig and Makefile changes.
CC: "Po-Yu Chuang" <ratbert@faraday-tech.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Move the Intel XScale IXP drivers into drivers/net/ethernet/xscale/
and make the necessary Kconfig and Makefile changes.
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the National Semi-conductor drivers into drivers/net/ethernet/natsemi/
and make the necessary Kconfig and Makefile changes. Also moved the 8390
(National Semi-conductor) devices as a sub-menu of National Semi-conductor
devices.
- moved the ibmlana driver as well into this directory since it is a
"SONIC" driver
CC: Alfred Arnold <alfred.arnold@lancom.de>
CC: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
CC: Harald Welte <laforge@gnumonks.org>
CC: Tim Hockin <thockin@hockin.org>
CC: <linux-ns83820@kvack.org>
CC: Kevin Chea <kchea@yahoo.com>
CC: Marc Gauthier <marc@linux-xtensa.org>
CC: Chris Zankel <chris@zankel.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Marc Gauthier <marc@tensilica.com>
Move the Apple drivers into driver/net/ethernet/apple/ and make the
necessary Kconfig and Makefile changes.
CC: Paul Mackerras <paulus@samba.org>
CC: Paul Mackerras <paulus@au.ibm.com>
CC: Russell Nelson <nelson@crynwr.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the STMicroelectronics driver into driver/net/ethernet/stmicro/ and
make the necessary Kconfig and Makefile changes.
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Tehuti driver into drivers/net/ethernet/tehuti/ and
make the necessary Kconfig and Makefile changes.
CC: Alexander Indenbaum <baum@tehutinetworks.net>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the PA Semi driver into drivers/net/ethernet/pasemi/ and
make the necessary Kconfig and Makefile changes.
CC: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Olof Johansson <olof@lixom.net>
Change details:
- Removec bfi_ll.h bna_hw.h bna_ctrl.c and bna_txrx.c due to ENET, MSGQ
and TXRX changes for new FW Driver interface and TX RX re-design.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
This patch contains additional structure and function definition changes
that are required to enable the new msgq/enet/txrx redesign introduced
by the previous 4 patches.
- structure and function definition changes to header files as a result
of Ethport, Enet, IOCEth, Tx, Rx redesign.
- ethtool changes to use new enet function and definitions
- Set number of Tx and Rx queues bassed on underlying hardware. Define
separate macros for maximum and supported numbers of Tx and Rx queues
based on underlying hardware. Take VLAN header into account for MTU
calculation. Default to INTx mode when pci_enable_msix() fails. Set a
bit in Rx poll routine, check and wait for that bit to be cleared in
the cleanup routine before proceeding.
- The TX and Rx coalesce settings are programmed in steps of 5 us. The value
that are not divisible by 5 are rounded to the next lower number. This was
causing the value os 1 to 4 to be rounded to 0, which is an invalid setting.
When creating Rx and Tx object, we are currently assigning the default
values of Rx and Tx coalescing_timeo. If these values are changed in the
driver to a different value, the change is lost during such operations as
MTU change. In order to avoid that, pass the configured value of
coalescing_timeo before Rx and Tx object creation. Fix
bnad_tx_coalescing_timeo_set() so it applies to all the Tx objects.
- Reorg uninitialization path in case of pci_probe failure.
- Hardware clock setup changes to pass asic generation, port modes and
asic mode as part firmware boot parameters to firmware.
- FW mailbox interface changes to defined asic specific mailbox interfaces.
h/w mailbox interfaces take 8-bit FIDs and 2-bit port id for owner. Cleaned
up mailbox definitions and usage for new and old HW. Eliminated usage of
ASIC ID. MSI-X vector assignment and programming done by firmware. Fixed
host offsets for CPE/RME queue registers.
- Implement polling mechanism for FW ready to have poll mechanism replaces
the current interrupt based FW READY method. The timer based poll routine
in IOC will query the ioc_fwstate register to see if there is a state
change in FW, and sends the READY event. Removed infrastructure needed to
support mbox READY event from fw as well as IOC code.
- Move FW init to HW init. Handle the case where PCI mapping goes away when
IOCPF state machine is waiting for semaphore.
- Add IOC mbox call back to client indicating that the command is sent.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Add new file bna_hw_defs.h to support new code MSGQ, ENET and TX RX redign.
This makes bna_hw.h obsolete and is removed in a later patch. bna_hw_defs.h
removes all unused HW register definition that were part of bna_hw.h.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- This patch contains the changes as a result of redesigning of Tx, Rx data
path setup. In the old design, setting up Txqs, Rxqs were done in the driver.
With the new design, most of the hardware setup steps for the Txq, Rxqs are
moved to FW. Host driver issues commands to FW through the message queue to
setup/teardown tx, rx data path. FW performs necessary steps and responds
back to the driver with a status.
- As a result of this redesign, the state machine implementation for Tx, Rx
objects have changed significantly. Instead of doing the raw register access,
these state machines mostly send a command to FW and wait for response and
take the next action. In addition to tx, rx datapath setup, this patch also
deals with rx filter configuration - such as unicast address, multicast
address, vlan filter, promiscuous mode etc.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- This patch contains the messages, opcodes and structure format for the
messages and responses exchanged between driver and the FW. In addition
this patch contains the state machine implementation for Ethport, Enet,
IOCEth.
- Ethport object is responsible for receiving link state events, sending
port enable/disable commands to FW.
- Enet object is responsible for synchronizing initialization/teardown of
tx & rx datapath configuration.
- IOCEth object is responsible for init/un-init of IO Controller in the
adapter which runs the FW.
- This patch also contains code for initialization and resource assignment
for Ethport, Enet, IOCEth, Tx, Rx objects.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Currently modules communicate with the FW using 32 byte command and
response register. This limits the size of the command and response
messages exchanged with the FW to 32 bytes. We need a mechanism to
exchange the comamnds and responses exchange with FW that exceeds 32 bytes.
- MSGQ implementation provides that facility. It removes the assumption that
command/response queue size is precisely calculated to accommodate all
concurrent FW commands/responses. The queue depth is made variable now, defined
by a macro. A waiting command list is implemented to hold all the commands
when there is no place in the command queue. Callback is implemented for
each command entry to invoke the module posting the command, when there is
space in the command queue and the command was finally posted to the queue.
Module/Object information is embedded in the response for tracking purpose.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Cisco driver into drivers/net/ethernet/cisco/ and make the
necessary Kconfig and Makefile changes.
CC: Christian Benvenuti <benve@cisco.com>
CC: Vasanthy Kolluri <vkolluri@cisco.com>
CC: Roopa Prabhu <roprabhu@cisco.com>
CC: David Wang <dwang2@cisco.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the IBM drivers into drivers/net/ethernet/ibm/ and make the
necessary Kconfig and Makefile changes.
- Renamed ibm_new_emac to emac
- Cleaned up Makefile and Kconfig options which referred to
IBM_NEW_EMAC to IBM_EMAC
- ibmlana driver is a National Semiconductor SONIC driver so
it was not moved
CC: Christoph Raisch <raisch@de.ibm.com>
CC: Santiago Leon <santil@linux.vnet.ibm.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Gibson <dwg@au1.ibm.com>
CC: Kyle Lucke <klucke@us.ibm.com>
CC: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Exar drivers into drivers/net/ethernet/neterion/ and make the
necessary Kconfig and Makefile changes.
CC: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Myricom drivers into drivers/net/ethernet/myricom/ and make
the necessary Kconfig and Makefile changes.
CC: Andrew Gallatin <gallatin@myri.com>
CC: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.
CC: Roland Dreier <roland@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the Brocade driver into drivers/net/ethernet/brocade/ and make
the necessary Kconfig and Makefile changes.
CC: Rasesh Mody <rmody@brocade.com>
CC: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the Emulex driver into drivers/net/ethernet/emulex/ and
make the necessary Kconfig and Makefile changes.
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the Solarflare drivers into drivers/net/ethernet/sfc/ and
make the necessary Kconfig and Makefile changes.
CC: Steve Hodgson <shodgson@solarflare.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the Sun drivers into drivers/net/ethernet/sun/ and make
the necessary Kconfig and Makefile changes.
Oliver Hartkopp <socketcan@hartkopp.net> suggested removing the
sun* prefix on the driver names. This type of change I will
leave up to the driver maintainers.
CC: Sam Creasey <sammy@sammy.net>
CC: Adrian Sun <asun@darksunrising.com>
CC: Benjamin Herrenscmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the Racal-Interlan driver into drivers/net/ethernet/racal/ and
make the necessary Kconfig and Makefile changes.
CC: "Jan-Pascal van Best" <janpascal@vanbest.org>
CC: Andreas Mohr <andi@lisas.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the drivers that use the i82586/i82593/i82596 chipsets into
drivers/net/ethernet/i825xx/ and make the necessary Kconfig and
Makefile changes. There were 4 3Com drivers which were initially
moved into 3com/, which now reside in i825xx since they all used
the i82586 chip.
CC: Philip Blundell <philb@gnu.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: <aris@cathedrallabs.org>
CC: Donald Becker <becker@scyld.com>
CC: Chris Beauregard <cpbeaure@undergrad.math.uwaterloo.ca>
CC: Richard Procter <rnp@paradise.net.nz>
CC: Andries Brouwer <aeb@cwi.nl>
CC: "M.Hipp" <hippm@informatik.uni-tuebingen.de>
CC: Richard Hirst <richard@sleepie.demon.co.uk>
CC: Sam Creasey <sammy@oh.verio.com>
CC: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the SMC (SMSC) drivers into drivers/net/ethernet/smsc/ and the
necessary Kconfig and Makefile changes. Also did some cleanup
of NET_VENDOR_SMC Kconfig tag for the 8390 based drivers.
CC: Nicolas Pitre <nico@fluxnic.net>
CC: Donald Becker <becker@scyld.com>
CC: Erik Stahlman <erik@vt.edu>
CC: Dustin McIntire <dustin@sensoria.com>
CC: Steve Glendinning <steve.glendinning@smsc.com>
CC: David Hinds <dahinds@users.sourceforge.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the QLogic drivers into drivers/net/ethernet/qlogic/ and
the necessary Kconfig and Makefile changes.
CC: Ron Mercer <ron.mercer@qlogic.com>
CC: Amit Kumar Salecha <amit.salecha@qlogic.com>
CC: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the drivers for the Chelsio chipsets into
drivers/net/ethernet/chelsio/ and the necessary Kconfig and Makefile
changes.
CC: Divy Le Ray <divy@chelsio.com>
CC: Dimitris Michailidis <dm@chelsio.com>
CC: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the drivers for Broadcom devices into
drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile
changes.
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Gary Zambrano <zambrano@broadcom.com>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the drivers for the National Semi-conductor 8390 chipset into
drivers/net/ethernet/8390/ and the necessary Kconfig and Makefile
changes.
CC: Donald Becker <becker@scyld.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Alain Malek <alain.malek@cryogen.com>
CC: Peter De Schrijver <p2@mind.be>
CC: "David Huggins-Daines" <dhd@debian.org>
CC: Wim Dumon <wimpie@kotnet.org>
CC: Yoshinori Sato <ysato@users.sourceforge.jp>
CC: David Hinds <dahinds@users.sourceforge.net>
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the drivers for the AMD chipsets into drivers/net/ethernet/amd/
and the necessary Kconfig and Makfile changes.
The au1000 (Alchemy) driver was also moved into the same directory
even though it is not a "Lance" driver.
CC: Peter Maydell <pmaydell@chiark.greenend.org.uk>
CC: Roman Hodek <Roman.Hodek@informatik.uni-erlangen.de>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
CC: Donald Becker <becker@scyld.com>
CC: Sam Creasey <sammy@users.qual.net>
CC: Miguel de Icaza <miguel@nuclecu.unam.mx>
CC: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
CC: Don Fry <pcnet32@frontier.com>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: David Davies <davies@maniac.ultranet.com>
CC: "M.Hipp" <hippm@informatik.uni-tuebingen.de>
CC: Pete Popov <ppopov@embeddedalley.com>
CC: David Hinds <dahinds@users.sourceforge.net>
CC: "Roger C. Pao" <rpao@paonet.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the 3Com drivers into drivers/net/ethernet/3com/ and the necessary
Kconfig and Makefile changes.
Did not move the following drivers becuase they use a non-3Com
chipset: 3c503, 3c505, 3c507, 3c523 and 3c527
CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
CC: David Dillow <dave@thedillows.org>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Alan Cox <alan@linux.intel.com>
CC: David Hinds <dahinds@users.sourceforge.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: David Dillow <dave@thedillows.org>
This is the initial patch to organize the drivers/net directory
structure and networking device driver config options. This patch
does the following:
- add drivers/net/ethernet/Kconfig
- integrate the new files into the existing config
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
