GTA04 can detect presence/absence or plug-in of an external
GPS antenna through a gpio. The best match for an event code
is SW_LINEIN_INSERT.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we can replace magic numbers by symbolic constants now.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are neither CD nor WP switches for mmc1. The µSD slot is
located under the SIM card under the battery and not accessible
during operation.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
vaux2 should remain always on since a higher potential at vio
could potentially damage the itg3200 sensor.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make clear how to use the wifi_reset since it is not obvious.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed to make the display and venc work properly.
Compare to omap3-beagle.dts.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
to better match omap3-beagle.dts (which was the basis
of designing the GTA04).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Vendor defined U-Boot has changed the partition scheme a while ago:
* kernel partition 6MB
* file system partition uses the remainder up to end of the NAND
* increased size of the environment partition (to get an OneNAND compatible base address)
* shrink the U-Boot partition
Let's be compatible (e.g. Debian kernel built from upstream).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we fix penirq polarity, add penirq pinmux and touchscreen
properties.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap dss susbystem takes the display aliases to find
out which displays exist. To enable tv-out we must define
an alias.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VENC with external OPA362 amplifier needs a special
"pinmux" setup in DEVCONF1 (TVOUTBYPASS and TVOUTACEN).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* fix connector compatibility (composite)
* add comment for gpio1 23
* add proper #address-cells
* we use only one venc_out channel for composite
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
needed for device variants based on GTA04 board but with
different display panel (driver).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
tab+space -> tab only for /* GSM audio */
spaces -> tab for dss_dpi_pins
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
S5M8767 PMIC interrupt line on Exynos5250-based Arndale board has
external pull-up resistors, so disable any pull control for it in
in controller node. This fixes support for S5M8767 interrupts and
enables operation of wakeup from S5M8767 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The SDHCI standard, MMC host controller bindings and MMC core defines
card detect pin as active low. Therefore there is no point to invert it
twice.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
PMIC node requires external interrupts for proper operation. Lack of them
was probably caused by a limited support for interrupts from more than one
parent, which was not possible to define when support for this board was
added. Fix this by adding 'interrupt-extended' property and properly
define both interrupt lines for PMIC node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
PMIC_IRQB and PMIC_KEYINB lines on Exynos4210-based Origen board have
external pull-up resistors, so disable any pull control for those lines
in respective pin controller node. This fixes support for MAX8997
interrupts and enables operation of wakeup from MAX8997 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 17419726aa ("ARM: dts: add max8997 device node for exynos4210-origen board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace the hardcoded clock indices by R9A06G032_CLK_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the LAN7515 on Raspberry Pi 3B+ doesn't have an EEPROM and the OTP
is empty, we need to enable the Ethernet LEDs via Device Tree.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Add the core display subsystem and vop nodes to rk3188.
Vop0 has a fully dedicated set of pins and only vop1 needs to
do pinctrl to have display output, so also add the necessary
pinctrl entries for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by Sandy Huang <hjc@rock-chips.com>
This patch enable the AHCI controller.
Since this controller need two regulator, this patch add them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
R40 have a sata controller which is the same as A20.
This patch adds a DT node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The clock controller registers are not 0x460 wide because the reset
controller starts at CBUS 0x4404. This currently overlaps with the
clock controller (which is at CBUS 0x4000).
There is no public documentation available on the actual size of the
clock controller's register area (also called "HHI"). However, in
Amlogic's GPL kernel sources the last "HHI" register is
HHI_HDMI_PHY_CNTL2 at CBUS + 0x43a8. 0x400 was chosen because that size
doesn't seem unlikely.
Fixes: 4a69fcd3a1 ("ARM: meson: Add DTS for Odroid-C1 and Tronfy MXQ boards")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock controller registers are not 0x460 wide because the reset
controller starts at CBUS 0x4404. This currently overlaps with the
clock controller (which is at CBUS 0x4000).
There is no public documentation available on the actual size of the
clock controller's register area (also called "HHI"). However, in
Amlogic's GPL kernel sources the last "HHI" register is
HHI_HDMI_PHY_CNTL2 at CBUS + 0x43a8. 0x400 was chosen because that size
doesn't seem unlikely.
Fixes: 2c323c43a3 ("ARM: dts: meson8: add and use the real clock controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Make use of the recently added &pinctrl and &watchdog labels. This
makes the whole file consistent and knowledge of the ahb/apb structure
is hidden.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Make use of the recently added &pinctrl and &watchdog labels. This
makes the whole file consistent and knowledge of the ahb/apb structure
is hidden.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
NOR and IFC controller connectivity is big-endian.
So add big-endian field in nor device tree node allowing
IFC controller to read/write data from/to the flash correctly.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6ULL is a lite version of i.MX6UL, its full name
is i.MX6 UltraLiteLite, NOT UlltraLite.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SLL has GPIO clock gates in CCM CCGR, add
clock property for GPIO driver to make sure all
GPIO banks work as expected.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signals available on both i.MX6UL and i.MX6ULL should have the same name
because it is the case of all others common signals, it avoids to make
mistakes (use the wrong ones) and it makes writing device tree files
less complicated. For example:
imx6ul-imx6ull-board.dtsi:
...
pinctrl_uart5: uart5grp {
fsl,pins = <
MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
>;
};
imx6ul-board.dts:
#include <imx6ul.dtsi>
#include <imx6ul-imx6ull-board.dtsi>
...
imx6ull-board.dts:
#include <imx6ull.dtsi>
#include <imx6ul-imx6ull-board.dtsi>
...
Without this patch, the imx6ull-board.dtb will use
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX instead of
MX6ULL_PAD_UART5_RX_DATA__UART5_DCE_RX and the uart5 will be
misconfigured.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Setting a stdout-path in the .dtb is convenient because then the user
gets a serial console on the RS-232 connector without any extra effort
of figuring out the relevant 'console=' boot parameter.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The WaRP7 has one mikroBUS socket on the back to plug click boards.
This patch allows to interact with some of these
i2c modules (EEPROM, RTC and so on).
Signed-off-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation" is based on the 1.5 version
of the i.Core MX6 cpu module. The 1.5 version differs from the original one for
a few details, including the ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup do to un-clocked
PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Fixes: 3fe0883577 ("ARM: dts: imx6q: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 1.5 version of Engicam's i.Core MX6 CPU module features a different clock
provider for the ethernet's PHY interface. Adjust the FEC ptp clock to
reference CLK_ENET_REF clock source, and set SION bit of
MX6QDL_PAD_GPIO_16__ENET_REF_CLK to adjust the input path of that pin.
The newly introduced imx6ql-icore-1.5.dtsi allows to collect in a single
place differences between version '1.0' and '1.5' of the module.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move usdhc2 and gpmi along with pinctrl nodes on
imx6ul-isiot.dtsi from dts files and mark it as 'disabled'
and the relevant dts will enable the status as 'okay'
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Define the Messaging Unit (MU) for i.MX7 in the processor's dtsi.
The respective driver is added in the next commit.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX7ULP B0 chip has some pin changes for USB and VIU
module, update pinfunc header file accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MC13892 Analog-to-Digital input pins (ADIN5-7) are exposed on the
imx51-babbage board.
Pass the "fsl,mc13xxx-uses-adc" property so that the MC13892 ADC
block can work.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX6SLL pinctrl driver, for details, please refer to
Documentation/devicetree/bindings/gpio/gpio.txt of "gpio-ranges"
property.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.
There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.
And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.
-----BEGIN PGP SIGNATURE-----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=CHc2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants against v4.19-rc1
These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.
There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.
And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.
* tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Signed-off-by: Olof Johansson <olof@lixom.net>
Add 3 helpers so that pincontrol definitions for pxa25x and pxa27x are
easier, and can be easily converted from old mfp mach-pxa code to
devicetree.
An example of such conversion would be :
static unsigned long mioa701_pin_config[] = {
GPIO32_MMC_CLK,
GPIO92_MMC_DAT_0,
GPIO109_MMC_DAT_1,
GPIO110_MMC_DAT_2,
GPIO111_MMC_DAT_3,
GPIO112_MMC_CMD,
MIO_CFG_IN(GPIO78_SDIO_RO, AF0),
MIO_CFG_IN(GPIO15_SDIO_INSERT, AF0),
MIO_CFG_OUT(GPIO91_SDIO_EN, AF0, DRIVE_LOW),
};
into:
pinctrl_mmc_default: mmc-default {
PMMUX(sd-insert, 15, gpio_in);
PMMUX(mmclk, 32, MMCLK);
PMMUX(sd-ro, 78, gpio_in);
PMMUX_LPM_LOW(sd-enable, 91, gpio_out);
PMMUX(mmdat0, 92, MMDAT<0>);
PMMUX(mmdat1, 109, MMDAT<1>);
PMMUX(mmdat2, 110, MMDAT<2>);
PMMUX(mmdat3, 111, MMDAT<3>);
PMMUX(mmcmd, 112, MMCMD);
};
The third column of PMMUX*() helpers can be found in pincontrol muxing
functions, either in pinctrl-pxa27x.c (or pinctrl-pxa25x.c), or by
inspecting the pincontrol once booted in debugfs.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Most devices use Broadcom standard partitions which allows them to be
described with the "brcm,bcm947xx-cfe-partitions". Exceptions are:
1) TP-LINK devices which use "os-image" partition with TRX containing
kernel only + separated rootfs partition.
2) Asus RT-AC87U with custom "asus" partition.
This commit also removes undocumented and unsupported linux,part-probe
binding which got accidentally upstreamed while describing SPI
controller.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There is one too many zeroes in the Power I2C base address. Fix this.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The RTC controller is fed by an external fixed 32kHz clock. Yet the
driver wants to acquire this clock, even though it doesn't make any use
of it, ie. doesn't get the rate to make calculation.
Therefore, use the exported 32.768kHz clock in the PXA clock tree to
make the driver happy and working.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Regulators, which are marked as 'on-in-suspend' seems to be critical for
board operation, thus they must not be disabled anytime. This can be
only assured by marking them as 'always-on', because otherwise some
actions of their clients might result in turning them off. This patch
restores suspend/resume operation on Peach-Pit Chromebook board. It
partially reverts 'always-on' property removal done by the commit
mentioned in the Fixes tag.
Fixes: 665c441eea ("ARM: dts: exynos: Remove unneded always-on for regulators on Peach boards")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Rename DT source for DE0 Nano SoC . The board name is really DE0-Nano-SoC
or Atlas SoC, and it is not to be confused with SoCkit board, which is a
different one. Rename the DT source file to match the board name and to
avoid this possible mixup with another different board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The NAND IP needs 3 clocks(nand_x_clk, nand_clk, and nand_ecc_clk). The
nand_x_clk and nand_ecc_clk are derived from the nand_clk. The nand_x_clk
has a fixed divider of 4.
Also, update the NAND dts property with the correct clocks property.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: add nand_ecc_clk and update commit message
The NAND IP needs 3 clocks(nand_x_clk, nand_clk, and nand_ecc_clk). This
patch adds a nand_clk, which is derived from the nand_x_clk, but has a
fixed divider of 4, and the nand_ecc_clk, which is derived from the
nand_x_clk.
Update the NAND node to use the additional clocks.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: add nand_ecc_clk and update commit message
Use stdout-path dts property for kernel console.
There were two socfpga boards left not using stdout-path:
socrates and vining. Make sure they match the other boards.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This patch adds missing properties to the CODEC and sound nodes, so the
audio will work also on Snow rev5 Chromebook. This patch is an extension
to the commit e9eefc3f8c ("ARM: dts: exynos: Add missing clock and
DAI properties to the max98095 node in Snow Chromebook")
and commit 6ab569936d ("ARM: dts: exynos: Enable HDMI audio on Snow
Chromebook"). It has been reported that such changes work fine on the
rev5 board too.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[krzk: Fixed typo in phandle to &max98090]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The LDO28 is used only on Odroid XU3 for Display Port. Define it so DTS
will describe entire hardware.
Depending on bootloader behavior this might affect the Display Port
because none of drivers are enabling it. By default it is off in S2MPS11
PMIC reset values. However it could be enabled by bootloader so in such
case kernel will later disable it as unused regulator.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Disable unused PMIC regulators on Exynos5422 Odroid boards to reduce
energy used. According to schematics:
1. LDO12, LDO16 and LDO24 are not connected,
2. LDO26 is not used on Odroid HC1.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Define LDO2, LDO23 and LDO27 critical board regulators to describe the
hardware.
Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
1 GHz CPU OPP is the default boot value for the Exynos5250 SOC, so mark it
as suspend OPP. This fixes suspend/resume on Samsung Exynos5250 Snow
Chomebook, which was broken since switching to generic cpufreq-dt driver
in v4.3.
Cc: <stable@vger.kernel.org> # 4.3.x: cd6f55457e: ARM: dts: exynos: Remove "cooling-{min|max}-level" for CPU nodes
Cc: <stable@vger.kernel.org> # 4.3.x: 672f33198b: arm: dts: exynos: Add missing cooling device properties for CPUs
Cc: <stable@vger.kernel.org> # 4.3.x
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Convert Exynos5250 to OPP-v2 bindings. This is a preparation to add proper
support for suspend operation point, which cannot be marked in opp-v1.
Cc: <stable@vger.kernel.org> # 4.3.x: cd6f55457e: ARM: dts: exynos: Remove "cooling-{min|max}-level" for CPU nodes
Cc: <stable@vger.kernel.org> # 4.3.x: 672f33198b: arm: dts: exynos: Add missing cooling device properties for CPUs
Cc: <stable@vger.kernel.org> # 4.3.x
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The pin controller block of S5Pv210 for handling external wakeup
interrupts is different than in newer designs (Exynos).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
HDMI-HPD was set active low, moreover by default pincontrol chip sets
pull-down on the pin. As a result HDMI driver assumes TV is always
connected regardless of actual state. The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
HDMI-DDC for unknown reasons doesn't work with Exynos I2C controllers.
Fortunately i2c-gpio comes to the rescue.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add to Arndale board: bridge and panel nodes, DSI properties and
regulators required by the bridge.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add common part of DSI node for Exynos5250 platforms and a required
mipi-phy node.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Otherwise we can get the following errors occasionally on some devices:
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 14329
...
I have one device that hits this error almost on every boot, and another
one that hits it only rarely with the other ones I've used behave without
problems. I'm not sure if the issue is related to a particular eMMC card
model, but in case it is, both of the machines with issues have:
# cat /sys/class/mmc_host/mmc1/mmc1:0001/manfid \
/sys/class/mmc_host/mmc1/mmc1:0001/oemid \
/sys/class/mmc_host/mmc1/mmc1:0001/name
0x000045
0x0100
SEM16G
and the working ones have:
0x000011
0x0100
016G92
Note that "ti,non-removable" is different as omap_hsmmc_reg_get() does not
call omap_hsmmc_disable_boot_regulators() if no_regulator_off_init is set.
And currently we set no_regulator_off_init only for "ti,non-removable" and
not for "non-removable". It seems that we should have "non-removable" with
some other mmc generic property behave in the same way instead of having to
use a non-generic property. But let's fix the issue first.
Fixes: 7e2f8c0ae6 ("ARM: dts: Add minimal support for motorola droid 4
xt894")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix wrong mode for dts file added by commit bb3e3fbbac
("ARM: dts: Add DT support for Octavo Systems OSD3358-SM-RED
based on TI AM335x").
Signed-off-by: Neeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Catch up with the new binding of the Denali IP where three clocks,
"nand", "nand_x", "ecc" are required.
For UniPhier SoCs, the "nand_x" and "ecc" are tied up because they
are both 200MHz.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the DT usable with the panel-lvds driver.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The atmel hlcdc controller has nothing to do with these pins, so move
them to where they belong.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The cd-gpios signal is assumed active-low by the driver, and the
cd-inverted property is needed if it is, in fact, active-high. Fix
this oversight.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
AT91_PINCTRL_OUTPUT_VAL(0) without AT91_PINCTRL_OUTPUT is a no-op, so
make sure the pins really output a zero.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Raspberry Pi Compute Module 3 (CM3) and the Raspberry Pi
Compute Module 3 Lite (CM3L) are SoMs which contains a BCM2837 processor,
1 GB RAM and a GPIO expander. The CM3 has a 4 GB eMMC, but on the CM3L
the eMMC is unpopulated and it's up to the user to connect their
own SD/MMC device. The dtsi file is designed to work for both modules.
There is also a matching carrier board which is called
Compute Module IO Board V3.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
As the new bindings are already in place in sama5d2.dtsi and that it's used
in the only Mainline board for this product (at91-sama5d2_ptc_ek.dts), we can
safely remove the old bindings.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix a typo. No functional change made by this patch.
Signed-off-by: Jay Foster <jayfoster@ieee.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch sets the pin muxing for the I2S controllers
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[codrin.ciubotariu@microchip.com: added pin muxing for the second
controller]
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch adds DT nodes for I2S0 and I2S1. It also adds an alias for
each I2S node.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[codrin.ciubotariu@microchip.com: removed unnecessary clock phandles]
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch adds two clock muxes for the two I2S
buses present on sama5d2 platforms.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add generic resistive touch device which is connected to ADC block
inside the SAMA5D2 SoC
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Browsing the DTS for all the R-Car SoCs with similar part numbers
still makes my head hurt, so to improve the user friendliness of
the 32-bit ARM DTS code base include R-Car Gen1 product names for
each DTSI file.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DA9063 OnKey subnode to DA9063 PMIC node on Stout.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DA9063 RTC and OnKey subnode to DA9063 PMIC node on Silk.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify EtherAVB PHY IRQ in the board specific device tree, now that we
have GPIO support.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DA9063 PMIC node to the I2C bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DA9210 DVFS node to the I2C bus and link it to CPU0 for DVFS.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU DT bindings have been updated to drop the reg-names property.
Update the r8a7792 and r8a7794 device trees accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adding pinctrl support for scif1 interface.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77470 part of the PFC device node.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded power domain indices by R8A77470_PD_* symbols.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the SATA device nodes on R-Car H1, H2, and M2-W to use a 2 MiB
I/O space, as specified in Rev.1.0 of the R-Car H1 and R-Car Gen2
hardware user manuals.
See also commit e9f0089b2d ("arm64: dts: r8a7795: Correct SATA
device size to 2MiB").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Another user of cd-inverted seems to have crept in. Switch it away from
cd-inverted to be consistent with other sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
imx23-evk board has a Seiko 43WVF1G parallel display.
Instead of hardcoding the display timings in the device tree, use
the "sii,43wvf1g" compatible instead.
This aligns with the new mxsfb bindings scheme documented at:
Documentation/devicetree/bindings/display/mxsfb.txt
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is recommended to place regulators outside simple-bus, so move them
accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx28-evk board has a Seiko 43WVF1G parallel display.
Instead of hardcoding the display timings in the device tree, use
the "sii,43wvf1g" compatible instead.
This aligns with the new mxsfb bindings scheme documented at:
Documentation/devicetree/bindings/display/mxsfb.txt
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is recommended to place regulators outside simple-bus, so move them
accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit 1c86c9dd82.
That commit followed the reference manual but unfortunately the imx7d
manual is incorrect.
Tested with ath9k pcie card and confirmed internally.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 1c86c9dd82 ("ARM: dts: imx7d: Invert legacy PCI irq mapping")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Bananapi M3 has an onboard IR receiver.
This enables the onboard IR receiver subnode.
Unlike the other IR receivers this one needs a base clock frequency
of 3000000 Hz (3 MHz), to be able to work.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The cir interface is like on the H3 located at 0x01f02000 and is exactly
the same. This patch adds support for the ir interface on the A83T.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The CIR Pin of the A83T is located at PL12.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Merge yet more updates from Andrew Morton:
- the rest of MM
- various misc fixes and tweaks
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
mm: Change return type int to vm_fault_t for fault handlers
lib/fonts: convert comments to utf-8
s390: ebcdic: convert comments to UTF-8
treewide: convert ISO_8859-1 text comments to utf-8
drivers/gpu/drm/gma500/: change return type to vm_fault_t
docs/core-api: mm-api: add section about GFP flags
docs/mm: make GFP flags descriptions usable as kernel-doc
docs/core-api: split memory management API to a separate file
docs/core-api: move *{str,mem}dup* to "String Manipulation"
docs/core-api: kill trailing whitespace in kernel-api.rst
mm/util: add kernel-doc for kvfree
mm/util: make strndup_user description a kernel-doc comment
fs/proc/vmcore.c: hide vmcoredd_mmap_dumps() for nommu builds
treewide: correct "differenciate" and "instanciate" typos
fs/afs: use new return type vm_fault_t
drivers/hwtracing/intel_th/msu.c: change return type to vm_fault_t
mm: soft-offline: close the race against page allocation
mm: fix race on soft-offlining free huge pages
namei: allow restricted O_CREAT of FIFOs and regular files
hfs: prevent crash on exit from failed search
...
Almost all files in the kernel are either plain text or UTF-8 encoded. A
couple however are ISO_8859-1, usually just a few characters in a C
comments, for historic reasons.
This converts them all to UTF-8 for consistency.
Link: http://lkml.kernel.org/r/20180724111600.4158975-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms@verge.net.au> [IPVS portion]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> [IIO]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and
PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor variants
of boards/platforms.
-----BEGIN PGP SIGNATURE-----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=J0qC
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
RTC alarm2 is connected to pmic_en line and hence can be used to control
the pmic enabling/disabling. Hence add the system-power-controller for rtc
node.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Vibration GPIOs don't have anything to do with wakeup. Move it to
normal section; this fixes vibrations on Droid 4.
Fixes: a5effd9683 ("ARM: dts: omap4-droid4: Add vibrator")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
- New support for the ASPEED USB host controller and USB vhub (device)
support
- Descriptions for the ColdFire processor that is part of the ASPEED
SoC
- Small fixes:
* pwm/tach clock
-----BEGIN PGP SIGNATURE-----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=aigP
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.19-devicetree-no-fsi' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
ASPEED device tree updates for 4.19
- New support for the ASPEED USB host controller and USB vhub (device)
support
- Descriptions for the ColdFire processor that is part of the ASPEED
SoC
- Small fixes:
* pwm/tach clock
* tag 'aspeed-4.19-devicetree-no-fsi' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Add coprocessor interrupt controller
ARM: dts: aspeed: Use 24MHz fixed clock for pwm
ARM: dts: aspeed: Fix Romulus VGA frame buffer
ARM: dts: aspeed: Enable vhub on port A of AST2500 EVB
ARM: dts: aspeed: Add G5 USB Virtual Hub
ARM: dts: aspeed: Add G4 USB Virtual Hub
ARM: dts: aspeed: Add G5 USB host pinmux
ARM: dts: aspeed: Add G4 USB pinmux
Signed-off-by: Olof Johansson <olof@lixom.net>
Our usual bunch of changes shared between arm and arm64.
This time, we have:
- eMMC support for the ALL-H3-CC boards
- EMAC support for the Beelink X2
-----BEGIN PGP SIGNATURE-----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=Blyi
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3/H5 changes for 4.19
Our usual bunch of changes shared between arm and arm64.
This time, we have:
- eMMC support for the ALL-H3-CC boards
- EMAC support for the Beelink X2
* tag 'sunxi-h3-h5-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi-h3-h5: Remove unused address-cells/size-cells of dwmac-sun8i
ARM: dts: sunxi: libretech-all-h3-cc: Enable eMMC module
ARM: sun8i: h3: add SY8113B regulator on Banana Pi M2 Zero board
ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2
ARM: dts: sun8i-h3: Add missing cooling device properties for CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>
There's a number of additions for the ARMv7 SoCs for this merge window, and
especially:
- Addition of the system controller for a number of SoCs, as part of the
VPU effort
- Addition of the R40 HDMI support
- Addition of the Mali GPU node for the A10
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE0VqZU19dR2zEVaqr0rTAlCFNr3QFAltXI44ACgkQ0rTAlCFN
r3TA1A//YKpmLTWhqTayqh7evsBtUvNET6sF21KG8NwMWShQoCpAFya9itS3ACc/
kFwguBtTdiefHRSwOYNJhl94YTb6xBYFv4dk47NaxuHLMpLHFXr+YmYypeIZ/wNc
P19R3s84n4HEvrhfyrsmA4FaLPLgRTzV23qLwPZrZHbKNv1mABuD3pruyGblbnKS
hCHSw9Gaw8AmEFxFbTwqeYZR4k8+TAFwYoYZPrdyPDtOhEaa5+hqVmfOSiorEtHG
OekbAj54rOYYPUPnEjEyj+sFtv4vK54h3qoWYH8B+XTr0svL5V8EQWooPzsnPTlE
OrgIXN9hPmz81WrdVBFf+nJnmuvACS1jpQX1U54WctGtyM/U4lFh2EoQFBfSDl9Q
cLzd6yyy/aG/YldFxtFImO7VSoVQWnIF7EDV6kKSvtWRyxc30fQz+SVW2Yh193Jj
bPi0SikBeekv9/XwBWTjY+ZDvoypJ10LQ8FqMuupB3v6TwsSTVIciZmcZpyxyp61
uEx4VGhGqoRc9GeQgJqLMAcUfAU1irUAaDePsD3eBRwn6Xla723M4QUhFPthnWZW
mANMz7WVLQXgsPl77m7SEU+ES8xma3ilgTC6Nm55NpG7bq4/icQp8vXHNClxPNvk
LoeXSpVWrnenP7DxLJFSldyPTrJAkDaije7eg5J0SJ5dJxpa+TY=
=3J2I
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.19
There's a number of additions for the ARMv7 SoCs for this merge window, and
especially:
- Addition of the system controller for a number of SoCs, as part of the
VPU effort
- Addition of the R40 HDMI support
- Addition of the Mali GPU node for the A10
* tag 'sunxi-dt-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (21 commits)
ARM: dts: sun4i: Add GPU node
ARM: dts: sun5i: Fix the SRAM A3-A4 declaration
ARM: dts: sun8i: r40: Remove unused address-cells/size-cells of dwmac-sun8i
ARM: dts: sun8i: a83t: Remove unused address-cells/size-cells of dwmac-sun8i
dt-bindings: net: dwmac-sun8i: Remove unused address-cells/size-cells
ARM: dts: sun8i: h3: Add SRAM controller node and C1 SRAM region
ARM: dts: sun8i: a23-a33: Add SRAM controller node and C1 SRAM region
ARM: dts: sun7i: Add support for the C1 SRAM region with the SRAM controller
ARM: dts: sun5i: Add support for the C1 SRAM region with the SRAM controller
ARM: dts: sun7i: Use most-qualified system control compatibles
ARM: dts: sun5i: Use most-qualified system control compatibles
ARM: dts: sun4i: Switch to new system control compatible string
ARM: dts: sun8i: r40: Disable TCONs by default.
ARM: dts: sun8i: r40: Add missing TCON-TOP - TCON connections
ARM: dts: sun8i: r40: Remove fallback compatible for TCON TV
ARM: dts: sun8i: r40: Add mixer ids to TCON TOP
ARM: dts: sun8i: r40: Remove fallback display engine compatible
ARM: dts: sun8i: a83t: Add CPU regulator supplies for A83T boards
ARM: dts: sun8i: r40: Enable HDMI output on BananaPi M2 Ultra
ARM: dts: sun8i: r40: Add HDMI pipeline
...
Signed-off-by: Olof Johansson <olof@lixom.net>
With ti-sysc driver working for most use cases, we can start converting
the omap variant SoCs to use device tree data for the interconnect target
modules instead of the legacy hwmod platform data.
We start with omap4 l4 devices excluding the ones that still depend on
a reset controller driver like DSP MMU. And we don't yet convert the l4
ABE instance as that needs a bit more work.
We also add a proper interconnect hierarchy for the devices while at it
to make further work on genpd easier and to avoid most deferred probe
issues.
At this point we are not dropping any platform data, and we initially
still use it to validate the dts data. Then in later merge cycles we
can start dropping the related platform data.
-----BEGIN PGP SIGNATURE-----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=ATsi
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/dt-pt3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Start using ti-sysc with device tree data for omap4 l4 devices
With ti-sysc driver working for most use cases, we can start converting
the omap variant SoCs to use device tree data for the interconnect target
modules instead of the legacy hwmod platform data.
We start with omap4 l4 devices excluding the ones that still depend on
a reset controller driver like DSP MMU. And we don't yet convert the l4
ABE instance as that needs a bit more work.
We also add a proper interconnect hierarchy for the devices while at it
to make further work on genpd easier and to avoid most deferred probe
issues.
At this point we are not dropping any platform data, and we initially
still use it to validate the dts data. Then in later merge cycles we
can start dropping the related platform data.
* tag 'omap-for-v4.19/dt-pt3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4: Add l4 ranges for 4460
ARM: dts: omap4: Move l4 child devices to probe them with ti-sysc
ARM: dts: omap4: Probe watchdog 3 with ti-sysc
ARM: dts: omap4: Add l4 interconnect hierarchy and ti-sysc data
dt-bindings: Update omap l4 binding for optional registers
Signed-off-by: Olof Johansson <olof@lixom.net>
* RZ/G1C (r8a77470) SoC: Use r8a77470-cpg-mssr binding definitions
* Add GR-Peach audio camera shield support with MT9V111 image sensor
* Add initial support for RZ/N1D (r9a06g032) SoC and its RZN1D-DB board
* Use SPDX identifiers in DT for all SoCs and boards
* Add missing OPP properties for all CPUs on various SoCs
* Add missing PMIC nodes to R-Car Gen2 M2-W (r8a7791) based porter board
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE4nzZofWswv9L/nKF189kaWo3T74FAltVvhcACgkQ189kaWo3
T76ABRAAsWkpVoxzMSj9c+qPtQ4r6aUsAF/gQfcU5eCdc4/v4YAhSzH2npY7CJ6N
kUCdqLXtOI/1CvNUL9jg/BSl88oiObryFlfhAWsiraN82yTp6426YfCFAht9Hynx
8hjEnp6M0D9dl6hKuA9Qn9V1PgM17nVLkuCkaCI1mgd3J0MNyUV0BGQJxZ+2/QmE
LfXmBywDgTtyrLiwpTWwRZT290X0xYMTHJnew4c7m7JSqlHi38EZJ3r/VqD/Cwkk
0fk/IDS4w9UFlwV326bjxyoozTnajgrcW6Gb40VPQYnJ+rD9FqnhPJilXhavJ/t/
AGNc9r8wMkYVwwfcYNvW9m1plfmpxiYulvOX6TKBp22yM0QiqLpu1C5gjSAce5i/
VH61eBDUYYMdXLtQfLoEv91pmJZmrWGs0IRSGHdaNSOUYyW3FtBBTIvfmpbB09JU
FNPCG1YFrCCndDKWPieYx056fydChYNK6S2a9nrAK97h5WiPxOpBnDET9dHkUMod
n50r+9Qr4ty68oOyJPqtHnSk3d5AU42I4iwSoiNLgbBWbvBLlmFe3Ov3B53rdVLD
DJ7ixGKYz1XaAuWDd72NVpDqeU60vVuvJJx+GOSIq0KXXn74ajcB/g4fekn/ZXMK
43gUB5MSzemgpRNmZi6Z78HF5ZmvQsCcl3yXuepdW0/k8CypVtk=
=jxlx
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.19
* RZ/G1C (r8a77470) SoC: Use r8a77470-cpg-mssr binding definitions
* Add GR-Peach audio camera shield support with MT9V111 image sensor
* Add initial support for RZ/N1D (r9a06g032) SoC and its RZN1D-DB board
* Use SPDX identifiers in DT for all SoCs and boards
* Add missing OPP properties for all CPUs on various SoCs
* Add missing PMIC nodes to R-Car Gen2 M2-W (r8a7791) based porter board
* tag 'renesas-arm-dt-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a77470: Use r8a77470-cpg-mssr binding definitions
ARM: dts: gr-peach: Add GR-Peach audiocamerashield support
ARM: dts: Renesas R9A06G032 SMP enable method
ARM: dts: Renesas RZN1D-DB Board base file
ARM: dts: Renesas R9A06G032 base device tree file
ARM: dts: convert to SPDX identifier for Renesas boards
ARM: dts: r8a77(43|9[013]): Add missing OPP properties for CPUs
ARM: dts: porter: Add missing PMIC nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a node for the CVIC (the coprocessor interrupt controller) and
add a label to the SRAM node so it can be referenced from the board
device-tree file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add mali gpu node to sun4i a10 platforms.
Tested with offscreen rendering with lima mesa (freedesktop gitlab)
Signed-off-by: Steven Vanden Branden <stevenvandenbrandenstift@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This pin is externally pulled up, so we need to disable the SoC's
internal pull down resistor to allow it to function properly.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This pin is externally pulled up, so we need to disable the
SoC's internal pull-down.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This pin is externally pulled up, so we should disable the SoC's
pull down resistor in order for the interrupt to function properly.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This pins are externally pulled up, and so we should explicitly
configure them to disable the SoC-internal pull-downs. Previously
we relied on the bootloader doing this in order to allow the buttons
to function properly.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently, we assume that the bootloader has correctly configured
the interrupt pin for max77693. This might not actually be the case -
so it's better to configure it explicitly.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace the hardcoded clock indices by R8A77470_CLK_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device tree header for GR-Peach's audiocamerashield with MT9V111
image sensor.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a special enable method for the second CA7 of the R9A06G032
as well as the default value for the "cpu-release-addr" property.
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds a base device tree file for the RZN1-DB board, with only the
basic support allowing the system to boot to a prompt. Only one UART is
used, with only a single CPU running.
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds the Renesas R9A06G032 bare bone support.
This currently only handles the SYSCTRL block note,
generic parts (gic, architected timer) and a UART.
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: updated MAINTAINERS file
[simon: do not use r9a06g032-sysctrl.h as it is not in the renesas tree yet]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (like, clock latency, voltage tolerance,
etc) as well to make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Add device tree support for i.MX6SLL SoC.
- New board support: ConnectCore 6UL System-On-Module and SBC Express;
ZII SCU2 Mezz, SCU3 ESB, SSMB SPU3 and CFU1 board; i.MX6SLL EVK
board; Engicam i.CoreM6 1.5 Quad/Dual MIPI; LogicPD MX31Lite board;
i.MX53 HSC/DDC boards from K+P.
- Remove fake regulator bus container node and enable USB OTG support
for i.MX6 wandboard and riotboard.
- Populate RAVE SP EEPROM, backlight, power button and watchdog devices
for ZII boards.
- Add cooling-cells for cpufreq cooling device, and add OPP properties
for all CPUs.
- A series from Anson Huang to enable LCD panel and backlight support
for imx6sll-evk board.
- Make pfuze100 sw4 regulator always-on for for a few Freescale/NXP
development boards, because the regulator is critical there and
cannot be turned off.
- Add more device support for i.MX5: AIPSTZ, SAHARA Crypto, M4IF,
Tigerp, PMU, CodaHx4 VPU.
- Enable PMU secure-reg-access for imx51-babbage, imx51-zii-rdu1 and
imx53-ppd board.
- Switch more device tree license to use SPDX identifier.
- Switch to use OF graph to describe the display for imx7d-nitrogen7.
- Add chosen/stdout-path for more boards, so that earlycon can be
enabled more easily on kernel cmdline.
- Convert GPC to new device tree bindings and add Vivante gpu nodes
for i.MX6SL SoC.
- Add more device support for imx6dl-mamoj board: parallel display,
WiFi and USB.
- A series from Stefan Agner to update i.MX6 apalis/colibri boards on
various aspects: SD/MMC card detection, regulators, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbUo3SAAoJEFBXWFqHsHzOtMAH/3UgJzGvYHIiOVVTAvwz3V5y
vZibWFOmzQDUcn3nrP54wGaMHT0abQ81AwrHKr0Bj1ujeJTCglRT8N5I/Dph6emU
aDSBIlv8y1fqF/96LhDk3bqGwg/pdF29dWBsaV45Va/ZZGErEzSTNlxV/n+nHkVy
S6rjGRkqk9abGmpDdJg2gYDYisDr9dl8iAEEBzBmOWLusEL2nvrqaMEmqBtVDFYd
fwLa+4HYZF3DaIfEjYy1INHeoCyBEAk8BS9u7b1jWTxONLNXh5GA6qFhiJgtZYrk
9+/mQ6D44fWkpJjWCOP4I12iRa5fr1UyVTslq4D6BmVK44Mhym/kyi9wXkv4fmc=
=j9qu
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree update for 4.19:
- Add device tree support for i.MX6SLL SoC.
- New board support: ConnectCore 6UL System-On-Module and SBC Express;
ZII SCU2 Mezz, SCU3 ESB, SSMB SPU3 and CFU1 board; i.MX6SLL EVK
board; Engicam i.CoreM6 1.5 Quad/Dual MIPI; LogicPD MX31Lite board;
i.MX53 HSC/DDC boards from K+P.
- Remove fake regulator bus container node and enable USB OTG support
for i.MX6 wandboard and riotboard.
- Populate RAVE SP EEPROM, backlight, power button and watchdog devices
for ZII boards.
- Add cooling-cells for cpufreq cooling device, and add OPP properties
for all CPUs.
- A series from Anson Huang to enable LCD panel and backlight support
for imx6sll-evk board.
- Make pfuze100 sw4 regulator always-on for for a few Freescale/NXP
development boards, because the regulator is critical there and
cannot be turned off.
- Add more device support for i.MX5: AIPSTZ, SAHARA Crypto, M4IF,
Tigerp, PMU, CodaHx4 VPU.
- Enable PMU secure-reg-access for imx51-babbage, imx51-zii-rdu1 and
imx53-ppd board.
- Switch more device tree license to use SPDX identifier.
- Switch to use OF graph to describe the display for imx7d-nitrogen7.
- Add chosen/stdout-path for more boards, so that earlycon can be
enabled more easily on kernel cmdline.
- Convert GPC to new device tree bindings and add Vivante gpu nodes
for i.MX6SL SoC.
- Add more device support for imx6dl-mamoj board: parallel display,
WiFi and USB.
- A series from Stefan Agner to update i.MX6 apalis/colibri boards on
various aspects: SD/MMC card detection, regulators, etc.
* tag 'imx-dt-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (96 commits)
ARM: dts: imx7d: remove "operating-points" property for cpu1
ARM: dts: vf610-zii-ssmb-spu3: Fix W=1 level warnings
ARM: dts: vf610: Add ZII CFU1 board
ARM: dts: imx6dl-mamoj: Add usb host and device support
ARM: dts: imx6dl-mamoj: Add Wifi support
ARM: dts: imx6dl-mamoj: Add parallel display support
ARM: dts: vf610: Add ZII SSMB SPU3 board
ARM: dts: imx6ul-pico-hobbit: Do not hardcode the memory size
ARM: dts: imx6sl-evk: make pfuze100 sw4 always on
ARM: dts: imx6sll-evk: make pfuze100 sw4 always on
ARM: dts: imx6sx-sdb-reva: make pfuze100 sw4 always on
ARM: dts: imx6qdl-sabresd: make pfuze100 sw4 always on
ARM: dts: imx6sl-evk: add missing GPIO iomux setting
ARM: dts: imx51-zii-scu3-esb: Fix RAVE SP watchdog compatible string
ARM: dts: imx51-zii-scu3-esb: Add switch IRQ line pinumx config
ARM: dts: imx6sx-nitrogen6sx: remove obsolete display configuration
ARM: dts: imx7d-nitrogen7: use OF graph to describe the display
ARM: dts: imx: Switch Boundary Devices boards to SPDX identifier
ARM: dts: imx6sl: Add vivante gpu nodes
ARM: dts: imx6sll-evk: enable SEIKO 43WVF1G lcdif panel
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- New boards from Laird: WB45N, WB50N, SOM60 modules and DVK, Gatwick
- fix the PMC compatibles
-----BEGIN PGP SIGNATURE-----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=XVdU
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.19-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
AT91 DT for 4.19:
- New boards from Laird: WB45N, WB50N, SOM60 modules and DVK, Gatwick
- fix the PMC compatibles
* tag 'at91-ab-4.19-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: fix typos for SSC TD functions
ARM: dts: add support for Laird SOM60 module and DVK boards
ARM: dts: add support for Gatwick board based on WB50N
ARM: dts: add support for Laird WB50N cpu module and DVK
ARM: dts: add support for Laird WB45N cpu module and DVK
ARM: dts: at91: add labels to soc dtsi for derivative boards
dt-bindings: add laird and giantec vendor prefix
ARM: dts: fix PMC compatible
ARM: at91: fix USB clock detection handling
dt-bindings: clk: at91: Document all the PMC compatibles
dt-bindings: arm: remove PMC bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (clocks, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds dts files for two new beaglebone variants for
Octavo Systems OSD3358-SM-RED and Sancloud am335x-sancloud-bbe.
-----BEGIN PGP SIGNATURE-----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=h3F9
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Few more beaglebone variants for v4.19 merge window
This adds dts files for two new beaglebone variants for
Octavo Systems OSD3358-SM-RED and Sancloud am335x-sancloud-bbe.
* tag 'omap-for-v4.19/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x: add am335x-sancloud-bbe board support
dt-bindings: Add vendor prefix for Sancloud
ARM: dts: Add DT support for Octavo Systems OSD3358-SM-RED based on TI AM335x
Signed-off-by: Olof Johansson <olof@lixom.net>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing property (clock latency) as well to make it all
work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Fix all nodes to use proper GIC_* macros for the interrupt type and the
interrupt trigger settings to avoid the boot warnings.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.
In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.
And we cannot yet move mmu_dsp until we have a proper reset controller
driver for rstctrl registers.
In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Before updating wdt2 to probe with ti-sysc we want to have wdt3
probed with ti-sysc to avoid having them unnecessarily swap order.
With ti-sysc, we probe child devices at module_init time while
and until l4 abe interconnect is converted to use ti-sysc, wdt3
will probe earlier with legacy platform data.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add proper interconnect hierarchy for l4 interconnect
instances with the related ti-sysc interconnect module data as
documented in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping
legacy platform data in arch/arm/mach-omap2/omap*hwmod*data.c
files later on in favor of ti-sysc dts data.
For setting up a proper hierarchy for the interconnect and
ti-sysc data, there are multiple reasons:
1. We can use dts ranges to protect registers from being
ioremapped from other devices and prevent hard to track
issues with failed flush of posted write between modules
2. Some of the ranges may not be accessible to operating systems
at all if configured so on high-security devices
3. The interconnect hierarchy provides proper clockdomain
hierarchy that can be used for genpd later on
4. We can avoid almost all deferred probe related issues simply
by probing the resource providing interconnect instance first
for l4 wkup instance
5. With deferred probe issues gone, we can probe everything
later at module_init time except for system timer and interrupt
controller and their clocks.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Each interconnect instance is typically divided into segments
to avoid powering up the whole interconnect. And each segment
has one or more ranges TI specific interconnect target modules
connected to it. Some devices can also have a separate data
access port directly to the parent L3 interconnect for DMA that
can be set up as a separate range.
Note that we cannot yet include this file from omap4.dtsi
until child devices are moved to their proper locations in
the interconnect hierarchy in the following patch. Otherwise
we would have the each module probed twice.
Also note that this does not yet add l4 abe instance, that will
be added separately later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit b97872d4eb ("ARM: dts: imx: Add missing OPP properties for CPUs")
added "operating-points" property for all CPUs, but i.MX7D already has
"operating-points-v2" property on both CPUs, so no need to add
"operating-points" property again, this patch removes it.
Fixes: b97872d4eb ("ARM: dts: imx: Add missing OPP properties for CPUs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- A fix for i.MX6 RDU2 board on the wrong IRQ type of Marvell switch,
which might result in a race condition in the interrupt handler and
cause the OS to miss all future events.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbUVhyAAoJEFBXWFqHsHzOss4H/3nHBKfbjC0twTK3J4ou3jDO
3JboghAt6bxKb/aS1zi8h3d7HDchV5FRkp87TX0qWss6RpS/cMPvQv2DCtgJIYMr
M/M59oxJJsZpen105tMiUFermrPEGz7vmy4FkmG8t2giSQj78XZYQnZsp77AcTyC
IP2wNcVBYwfis3GvDuKgBduZlAV42tqL0U02HsaOvmHjhGcqLzJxlwDAa2es6/zU
KmbBatTR78oP2xf68BXQVB+x8WEjLxNI9J3c4uuLjYTxDxCKU+QNi57XS1VXp13q
72x0lxhe9uTOC+tipvTvj449RigOIfqhlyg7IIE/5xOIKZFUfZZSYZmQ00lx1O4=
=grcI
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.18, round 4:
- A fix for i.MX6 RDU2 board on the wrong IRQ type of Marvell switch,
which might result in a race condition in the interrupt handler and
cause the OS to miss all future events.
* tag 'imx-fixes-4.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: RDU2: fix irq type for mv88e6xxx switch
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix typo for TD function of pins PIN_PB22 and PIN_PC14
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This adds support for Lairds upcoming SOM module, featuring Marvell WiFi
and Bluetooth, 2Gb NAND / 1Gb LPDDR SDRAM, and an Atmel SAMA5D3 CPU.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for the LoRa gateway from Laird, the RG1xx.
This board houses the WB50NBT CPU module along with a Semtech SX1301 based
concentrator card.
https://www.lairdtech.com/products/rg1xx-lora-gateway
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This adds support for Lairds CPU module, featuring Atheros wifi, CSR
Bluetooth and, Atmel SAMA5D3 CPU.
https://www.lairdtech.com/products/wb50nbt-wi-fi-bluetooth-module
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This adds support for Lairds combo CPU module, featuring on board
Atheros wifi, CSR Bluetooth radio and, Atmel CPU.
https://www.lairdtech.com/products/wb45nbt
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This adds labels to commonly used device-tree nodes so that derivative
boards can avoid ahb/apb hierarchy.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Marvell switches report their interrupts in a level sensitive way.
When using edge sensitive detection a race condition in the interrupt
handler of the swich might result in the OS to miss all future events
which might make the switch non-functional.
The problem is that both mv88e6xxx_g2_irq_thread_fn() and
mv88e6xxx_g1_irq_thread_work() sample the irq cause register
(MV88E6XXX_G2_INT_SRC and MV88E6XXX_G1_STS respectively) once and then
handle the observed sources. If after sampling but before all observed
irq sources are handled a new irq source gets active this is not noticed
by the handler which returns unsuspecting, but the interrupt line stays
active which prevents the edge detector to kick in.
All device trees but imx6qdl-zii-rdu2 get this right (most of them by
not specifying an interrupt parent). So fix imx6qdl-zii-rdu2
accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: f64992d1a9 ("ARM: dts: imx6: RDU2: Add Switch interrupts")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The dts patch for droid4 PWM vibrator has added gpio6 entries to the wrong
node. Let's fix it with a note that there seems to be also other GPIO PWM
issues to fix still to get the PWM vibrator working. So this can wait for
v4.19 merge cycle if necessary.
-----BEGIN PGP SIGNATURE-----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=1jV8
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
One omap dts mismerge fix
The dts patch for droid4 PWM vibrator has added gpio6 entries to the wrong
node. Let's fix it with a note that there seems to be also other GPIO PWM
issues to fix still to get the PWM vibrator working. So this can wait for
v4.19 merge cycle if necessary.
* tag 'omap-for-v4.18/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: fix dts w.r.t. pwm
Signed-off-by: Olof Johansson <olof@lixom.net>
According to the system control bindings, the A3-A4 SRAM node should be
a child node of the SRAM it belongs to. However, it was introduced at the
same level, therefore breaking the binding. Fix this.
Fixes: 8587019625 ("ARM: sun5i: a13: Merge common controllers into the common DTSI")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
address-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
address-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
ddress-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
dts reports incorrect usage of these properties in gpio-keys node.
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary
The patch is removing these useless properties.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add an LED node, connected to the Processing System (PS)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Include GPIO dt-bindings and use GPIO_ACTIVE_* constants
to improve readability
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
According to the reference manual, the board has two Micron
MT41K256M16HA-125 DDR3L memory ICs, which have 512 MiB each
Tested on a ZYBO-Z7-20 board
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both boards are made by Avnet, Inc. So add an additional
value to the compatible property
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a dts for MYIR Z-turn board and respective target in Makefile.
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds parallel display support for i.MX6DL Mamoj board
along with relevant backlight through pwm.
LCD power sequence is added by 'Michael Trimarchi'.
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The aspeed pwm driver always sets the clock source to 24MHz, specify
the fixed clock in device tree to make sure the driver is using the
correct clock frequency to calculate the fan speed.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the Ethernet and Realtek switch device to the
D-Link DIR-685 Gemini-based device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Tested on a revision G board.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are two variants of imx6ul-pico boards: one with 256MB and
another one with 512MB of RAM.
Do not hardcode the memory size in the device tree and let the
bootloader fill the correct value instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SL EVK board, pfuze100 sw4 supplies
LPDDR2 which is critical for system, must be
always on.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, pfuze100 sw4 supplies
LPDDR3 which is critical for system, must be
always on.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SX SDB Rev-A board, pfuze100 sw4 supplies
csi, audio codec and i2c etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6QDL Sabre-SD board, pfuze100 sw4 supplies
GPS, touch and RGMII etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OSD3358-SM-RED is a dev board for OSD335x System-in-Package(SiP) devices from
Octavo Systems.
This board family can be indentified by the A335BNLTOS00 in the at24 eeprom:
A2: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 4f 53 30 30 |.U3.A335BNLTOS00|]
https://octavosystems.com/octavo_products/osd3358-sm-red/
Signed-off-by: Neeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On i.MX6SL EVK board, the MX6SL_PAD_KEY_ROW5 pin is
used as lcd 3v3 regulator control pin, need to make
sure MX6SL_PAD_KEY_ROW5 is muxed as GPIO function
for controlling lcd 3v3 regulator.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by; Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It looks like I made a nasty typo in the original patch which resulted
in missing watchdog device. Fix it.
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of relying on default values, configure PAD_AUD3_BB_CK to be a
GPIO explicitly. While at, it change the pad configuration to enable
a 100K pull-down (the pin is used as IRQ_TYPE_LEVEL_HIGH).
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pwm node should not be under gpio6 node in the device tree.
This fixes detection of the pwm on Droid 4.
Fixes: 6d7bdd328d ("ARM: dts: omap4-droid4: update touchscreen")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[tony@atomide.com: added fixes tag]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This display configuration isn't working as-is as it depends on the
tfp410 LCD to HDMI bridge. This will need to be updated later once
the DRM MXSFB driver will be the default.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To make use of the new eLCDIF DRM driver OF graph description is
required. Describe the display using OF graph nodes.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6sl soc has gpu_2d and gpu_vg, no 3d support:
etnaviv-gpu 2200000.gpu: model: GC320, revision: 5007
etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215
The IP blocks seem to be already supported.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, lcd regulator is controlled
by GPIO4 IO03 using MX6SLL_PAD_KEY_ROW5__GPIO4_IO03 pin,
NOT MX6SLL_PAD_ECSPI1_SCLK__GPIO4_IO08, correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[fabio: kept the change only in imx53-ppd context]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ConnectCore 6UL Single Board Computer (SBC) Express contains the
ConnectCore 6UL System-On-Module.
Its hardware specifications are:
* 256MB DDR3 memory
* 256MB NAND flash
* Single Ethernet
* USB Host and USB-OTG
* MicroSD external storage
* Groove connectors and Raspberry Pi Hat compatible expansion header
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ConnectCore 6UL System-On-Module has the following hardware
specification:
* Based on a NXP i.MX6UL SoC
* Industrial temperature ranges (-40ºC to +85ºC)
* Up to 1GB DDR3 memory
* Up to 2GB NAND flash
* Dual Ethernet
* On module 802.11 WiFi and Bluetooth 4.2 (QCA6564)
* On module NXP Kinetis KL03
* On module Microchip ATECC508A crypto element
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx51-zii-rdu1 has an external watchdog in the environment
microcontroller, so disable the internal one.
This aligns with what was done in commit 7055f71403 ("ARM: dts:
imx6: RDU2: disable internal watchdog") for imx6 rdu2 board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Normally, we didn't release this kind of baord to user. This specific
board exists only in the early stage of development inside MediaTek -
and that may confuse peoples.
Hence this patch removes related files accordingly.
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The reserved memory for the VGA frame buffer is at the wrong address
for this system.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is an eval board, it makes sense to enable many
functions by default. This changes the device-tree to
set port A to be a USB device and leave port B as a
host, along with a little comment explaining how to
change it.
(the vhub device can only exist on port A on this SoC)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the (disabled by default) device node for the
Aspeed virtual hub,a long with clocks and pinmux.
This also adds the missing pinmux definition for it
(the kernel driver already knows about it).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the (disabled by default) device node for the
Aspeed virtual hub,a long with clocks and pinmux.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set the default pinmux for EHCIs so boards don't have to do
it an document why it is not set for UHCI.
Remove the properties from the AST2500 EVB board which are
now redundant
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set the default pinmux for EHCI so boards don't have to do
it, and document why it is not set for UHCI.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Pio-leds (near GPIO-Header) are swapped and LOW-active.
This patch restores the expected behaviour.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Add Vitesse switch chips
- Add a new DT for a reference design
-----BEGIN PGP SIGNATURE-----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=3RrW
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Gemini DTS updates for v4.19:
- Add Vitesse switch chips
- Add a new DT for a reference design
* tag 'gemini-dts-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add devicetree for Storlink/Storm SL93512R
ARM: dts: Add Vitesse G5e switch to the Gemini SQ201
ARM: dts: Add WAN ethernet port to the SQ201
Signed-off-by: Olof Johansson <olof@lixom.net>
The Storlink Gemini324 EV-Board also known as Storm
Semiconductor SL93512R_BRD is ground zero for the Gemini
devices. We add a device tree so we can support it, it
turns out to be pretty trivial.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the Vitesse G5e ethernet switch to the Square
One Itian SQ201 router device tree.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This sets up the ethernet interface and PHY for the
WAN ethernet port which uses a Marvell PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Turns out the recent patches for ARM branch predictor hardening are
not working on omap5 and dra7 as planned because the secondary CPU
is parked to the bootrom code. We can't configure it in the bootloader.
So we must enable invalidates of BTB for omap5 and dra7 secondary
core in the kernel.
And there's a fix for reserved register access for am3517. The
usb otg module on am3517 is not the same as for other omap3.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAltImsMRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXOqNw/7BAD1n1sS2Sq+6QdYLNvWkxlstcarDf29
5jolIQJCaa60WF9C1oTaoy59+UcaiLyk2dWYGgi1ZDce4ihhyIhQUFscHab2Zh0B
o4zGXuTnTRBRiCKSI3ue8MTLTpYkuSmoTfWJu3ACEmR0co9J9sHztYz4yd1vj7E6
tWvYLsYv7av4URBNaL4ieeUAZrailRQ3l5vg/+fJ7Xhk1+Ue3bQUmb3DDtypD1Ub
OVFVtHGJdxDLaKJ0fhYPIoZYLhIe9BSuxboGrmh/vpyn6kuZ2Q/iWFSyX4kfveoH
uEPWzJ6xMe0XNsxyuZ9bYO1rsBrOxXGzZNrgmiLI+GQ4uTK+e68vHPOimtWsNVb1
hMpr8eTiyEUR/lhtMVoizGVPiNnJfhfnbIrUx5g80mAiwogIp9p3IEYHQD2zh4Ly
susyjPV9TWoesS1RUrJz2N59qLgSPdOYhmfpaYmc31mVEXu+TiDDxyrUNz++or10
UfJIo/MGDoIWbuRPMRfQEzdJqv13D0FuVbXkgaNWIvAnuDlqQx27dQLDRPepZqS3
kHeOwrxf4h6NrlbCAdF4wn34WLbuMIdpp6rxstGsPi9TVR3PytetBtMlqMkJnfd6
Yg3WcbN695ZNEod1tJhj5E8yUAdYtYPFKSX0egF4z/HrZ4NrjG/JB0gSXXSeS2Q7
X7ecetNHONs=
=Wci4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two omap fixes for v4.18-rc cycle
Turns out the recent patches for ARM branch predictor hardening are
not working on omap5 and dra7 as planned because the secondary CPU
is parked to the bootrom code. We can't configure it in the bootloader.
So we must enable invalidates of BTB for omap5 and dra7 secondary
core in the kernel.
And there's a fix for reserved register access for am3517. The
usb otg module on am3517 is not the same as for other omap3.
* tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the new thermal binding on Armada 38x allowing to use a driver fix
which is already part of the kernel.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCW0eB8QAKCRALBhiOFHI7
1a0PAKCRyt0vXcjr9HHBzhagibfgT4XrXgCfXG43C32Qjg5U1Ga39IIY3fcFMrY=
=2Pjz
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.18-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.18 (part 1)
Use the new thermal binding on Armada 38x allowing to use a driver fix
which is already part of the kernel.
* tag 'mvebu-fixes-4.18-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: use the new thermal binding
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAltGCisQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgfrxCACbf7LkN/oH1MekD7CTaGHwlyvyneVWT/Dl
wM0YdKJ4fpZ6FMWxGV4F32qdkSEyPxCVTe1mnueOVnDgZX/ywPGC/hpbofPbmZuq
Z2/YFfCNzsBcijlhwI5bZrzChl/AKKOZNqGBxpKz+lXe/6dIl8bTG8Fmi3tvA+oy
hhvy0Sl6JeNqI5NghEukrQOuEYPHdniElTBYP8DP0J8yypbuIVFOzqpRtoOKeSCP
669aN5G5tCRYoJlx0pC2FyqTI0bdCPtPLPZx9eQwMqyFGN4EUx7NGB3w4gH4GubT
vfG4K4cK3CSWr7+LfwqkA2cX2gzPpGpUyaCpROHkGxtxqcMFdIrV
=ZfMG
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Fix for a new warning from dtc in graph node unit addresses.
* tag 'v4.18-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix graph node unit address error from dtc
Signed-off-by: Olof Johansson <olof@lixom.net>
After the work done by Thomas Petazzoni, the NAND chip timings
can be read out from the chip instead of open coded in the
device tree, so let's just remove the timing information.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Highlights:
----------
-MCU platforms update:
-Update RTC syscfg bindings on stm32f746 and stm32f429
-Update IWDG node with LSI clock name on stm32f429
-MPU STM32MP157 platform update:
-Add HASH support
-Add m_can support and enable it on EV1 board
-Add RTC suppoort and enable it on ED1 board
-Add USB OTG HS support and enable it on EV1 board
-Enable USB Host EHCI on EV1 board
-Add DFSDM support
-Add SPI support
-Add ETH support and enable it on EV1 board
-Add IWDG support and enable it on ED1 board
-Fix useless GPIO aliases and reorder nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJbSK1NAAoJEH+ayWryHnCFMesP/2OFNwl1ZHpU5aoRfqIP4Xy8
ATKQh56FVLbtEaqBffze2pc8F1y9Id6H7UpFSsZ+IujeviIQ2sjh/hMeFq3arxeE
w66yS6YJjyZaBIWsGyit50xiAelNEbDmmdL3RhIa4T9nyYuOQ9c38S7GTxeO3hLv
6FIXffb8v76qaypKqqCdGImO/7V4L7nNPiGzCxyHhVFv7z76/kBgkjPn4BeoeW0N
yzDYW/WDBL+XDMaxwB7NmK3RlMbYLxEPpbWmqddibU/azaRXNNkgtC5+75Cbfrd4
BOAAGfiBKhRLYnQ6tdOhl/Ru+NR7Nig3Nxp92c9M53prDHfZw1+vX5s64wrvI2nR
0zKZiLpHNxXquhdqQ9a4GszF9KAtHM+cym9nXeYsfbBroOrv9N/E8ndz1EiyHErd
3anZsn0ILrcYtBnzdmRWBWfJDYVefJHwB8a1nq6UK8zGwBnKZtfOx4iBSztrcsS9
JcbN5yYdYVfQTjkKCpHGMhQwMdlh8h0yjGds2D2ySfoOSweYlNrfdRYGx03N8p3z
4RPLuGVYQ/shcPUaapwm9Ity1KmxTcDIEA6WgRI6VNypwdQbslMEfpZqdNTduHjO
JzPJEO67yPzimGQ7u5ZGTlJtdUxTDHpXGX2q67QqwzM/jbVpqSsArcr1LgDifI4g
P6pT4uu87oPlbVwBIHUE
=Tc+I
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
STM32 DT updates for v4.19, round 1
Highlights:
----------
-MCU platforms update:
-Update RTC syscfg bindings on stm32f746 and stm32f429
-Update IWDG node with LSI clock name on stm32f429
-MPU STM32MP157 platform update:
-Add HASH support
-Add m_can support and enable it on EV1 board
-Add RTC suppoort and enable it on ED1 board
-Add USB OTG HS support and enable it on EV1 board
-Enable USB Host EHCI on EV1 board
-Add DFSDM support
-Add SPI support
-Add ETH support and enable it on EV1 board
-Add IWDG support and enable it on ED1 board
-Fix useless GPIO aliases and reorder nodes
* tag 'stm32-dt-for-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (22 commits)
ARM: dts: stm32: update iwdg with lsi clock name for stm32f429
ARM: dts: stm32: add iwdg2 support for stm32mp157c-ed1
ARM: dts: stm32: add iwdg2 support for stm32mp157c
ARM: dts: stm32: Reorder nodes in stm32mp157c-ed1
ARM: dts: stm32: remove gpio aliases for stm32mp157c
ARM: dts: stm32: add support of ethernet on stm32mp157c-ev1
ARM: dts: stm32: Add ethernet dwmac on stm32mp1
ARM: dts: stm32: Add syscfg on stm32mp1
ARM: dts: stm32: add SPI1 support on stm32mp157c-ev1
ARM: dts: stm32: add SPI support on stm32mp157c
ARM: dts: stm32: Add DFSDM support to stm32mp157c
ARM: dts: stm32: Add ADC support to stm32mp157c
ARM: dts: stm32: enable USB OTG HS on stm32mp157c-ev1
ARM: dts: stm32: add USB OTG HS support for stm32mp157c SoC
ARM: dts: stm32: enable USB Host (USBH) EHCI controller on stm32mp157c-ev1
ARM: dts: stm32: enable RTC on stm32mp157c-ed1
ARM: dts: stm32: add RTC support to stm32mp157c
ARM: dts: stm32: m_can activation on stm32mp157c-ev1
ARM: dts: stm32: m_can support to stm32mp157c
ARM: dts: stm32: Add HASH support on stm32mp157c
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add a new Armada 388 based board: helios4
- Enable SPI flash by default on SolidRun Armada 38x Microsom
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCW0hvzAAKCRALBhiOFHI7
1eiZAJ4khxwKduQLyzz0nqyaX7jefrb7ywCfY8WXMc0ay/qwZytGcUUqpWMeY3Y=
=OVdR
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.19-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.19 (part 1)
- Add a new Armada 388 based board: helios4
- Enable SPI flash by default on SolidRun Armada 38x Microsom
* tag 'mvebu-dt-4.19-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada388-clearfog: drop future changes disclaimer
ARM: dts: armada388-clearfog: enable spi flash
ARM: dts: armada388-helios4
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add two new S5Pv210 boards: Samsung Galaxy S and Samsung Galaxy S 4G
mobile phones. Both are from family codenamed Aries. The Samsung
Galaxy S was released on the market in 2010 with Android operating
system. At that time, it was the Samsung's flagship model.
This brings support for storage (SD card and internal memory), PMIC,
RTC, fuel-gauge, keys, USB (in peripherial mode) and WiFi.
2. Add missing secondary CPU properties.
3. Cleanup from old files and properties.
-----BEGIN PGP SIGNATURE-----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=afvE
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.19
1. Add two new S5Pv210 boards: Samsung Galaxy S and Samsung Galaxy S 4G
mobile phones. Both are from family codenamed Aries. The Samsung
Galaxy S was released on the market in 2010 with Android operating
system. At that time, it was the Samsung's flagship model.
This brings support for storage (SD card and internal memory), PMIC,
RTC, fuel-gauge, keys, USB (in peripherial mode) and WiFi.
2. Add missing secondary CPU properties.
3. Cleanup from old files and properties.
* tag 'samsung-dt-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: samsung: Document bindings for SGH-T959P board
dt-bindings: samsung: Document bindings for Samsung aries boards
ARM: dts: s5pv210: Add initial DTS for SGH-T959P phone
ARM: dts: s5pv210: Add initial DTS for Samsung Galaxy S phone
ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones
ARM: dts: s5pv210: Add missing interrupt-controller property to gph2
ARM: dts: exynos: remove no longer needed samsung thermal properties
dt-bindings: arm: Remove obsolete insignal-boards.txt
ARM: dts: exynos: Add missing CPU clocks to secondary CPUs on Exynos542x
arm: dts: exynos: Add missing cooling device properties for CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>
This set of changes adds support for the memory client resets on Tegra20
and Tegra30, fixes a couple of issues on Cardhu and Tegra30 Apalis as
well as adds a unit-address to the memory node to avoid warnings from
DTC. To round things of, the NAND flash controller is enabled on the
Tegra20 Colibri.
-----BEGIN PGP SIGNATURE-----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=+IHO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.19-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.19-rc1
This set of changes adds support for the memory client resets on Tegra20
and Tegra30, fixes a couple of issues on Cardhu and Tegra30 Apalis as
well as adds a unit-address to the memory node to avoid warnings from
DTC. To round things of, the NAND flash controller is enabled on the
Tegra20 Colibri.
* tag 'tegra-for-4.19-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra: enable NAND flash on Colibri T20
ARM: dts: tegra: add Tegra20 NAND flash controller node
ARM: tegra: Work safely with 256 MB Colibri-T20 modules
ARM: tegra: Fix unit_address_vs_reg and avoid_unnecessary_addr_size DTC warnings
ARM: tegra: Fix unit_address_vs_reg DTC warnings for /memory
ARM: tegra: Remove usage of deprecated skeleton.dtsi
ARM: tegra: Fix can2 on Tegra30 Apalis
ARM: tegra: Fix Tegra30 Cardhu PCA954x reset
ARM: dts: tegra30: Add Memory Client reset to VDE
ARM: dts: tegra20: Add Memory Client reset to VDE
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes configure the mcan clock, interconnect target
module and mcan device. These changes depend on the ti-sysc
related driver changes and are based on those.
Notably this is the first new driver that probes with ti-sysc
driver with no legacy hwmod platform data for the interconnect
target module.
-----BEGIN PGP SIGNATURE-----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=v277
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/dt-mcan-v2-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
dts changes for mcan for omaps for v4.19 merge window
These changes configure the mcan clock, interconnect target
module and mcan device. These changes depend on the ti-sysc
related driver changes and are based on those.
Notably this is the first new driver that probes with ti-sysc
driver with no legacy hwmod platform data for the interconnect
target module.
* tag 'omap-for-v4.19/dt-mcan-v2-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra76x: Add MCAN node
ARM: dts: Add generic interconnect target module node for MCAN
ARM: dts: dra762: Add MCAN clock support
bus: ti-sysc: Add support for software reset
bus: ti-sysc: Add support for using ti-sysc for MCAN on dra76x
clk: ti: dra7: Add clkctrl clock data for the mcan clocks
bus: ti-sysc: Use 2-factor allocator arguments
Signed-off-by: Olof Johansson <olof@lixom.net>
Mostly updates to configure and improve the devices
found on various SoCs and boards:
- several patches to update support for am3517-evm
to replace bogus fixed regulators with proper
regulators and configure various devices such
as wlan, bluetooth and usb1
- add missing cooling devices for omap5 and dra7
- configure dual role for usb ports for am57xx
and dra7
- PM updates for omap4 devices to allow retention
idle for minimal configurations
- am335x-sl50 updates for various devices
- update d-can alias names to not use undescore
- configure pandaboard gpio button
- a non-urgent change to fix dcan node address that
i forgot to send a pull request for earlier
-----BEGIN PGP SIGNATURE-----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=kbfH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
dts changes for omaps for v4.19 merge window
Mostly updates to configure and improve the devices
found on various SoCs and boards:
- several patches to update support for am3517-evm
to replace bogus fixed regulators with proper
regulators and configure various devices such
as wlan, bluetooth and usb1
- add missing cooling devices for omap5 and dra7
- configure dual role for usb ports for am57xx
and dra7
- PM updates for omap4 devices to allow retention
idle for minimal configurations
- am335x-sl50 updates for various devices
- update d-can alias names to not use undescore
- configure pandaboard gpio button
- a non-urgent change to fix dcan node address that
i forgot to send a pull request for earlier
* tag 'omap-for-v4.19/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: pandaboard: add gpio user button
ARM: dts: am3517-evm: Add 'vdd_io_reg' regulator references
ARM: dts: am3517-evm: Enable USB1 Host
ARM: dts: am33xx: Fix syntax of alias names
ARM: dts: am3517-som: Add builtin Bluetooth
ARM: dts: am3517-som: Add WL127x Wifi
ARM: dts: am335x-sl50: enable tsadc on SL50 board
ARM: dts: am335x-sl50: fix label names for all LEDs
ARM: dts: am335x-sl50: use audio-graph-card for sound
ARM: dts: am335x-sl50: add support for DS1339 Real Time Clock
ARM: dts: am335x-sl50: set dr_mode to otg
ARM: dts: am335x-sl50: add a node for the LCD controller
ARM: dts: am335x-sl50: use phy-phandle declarations
ARM: dts: am335x-sl50: update backlight nodes
ARM: dts: omap4-droid4: Use software debounce for gpio-keys
ARM: dts: Configure duovero for to allow core retention during idle
ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt
ARM: dts: dra76-evm: Add VBUS GPIO to USB1/USB2 extcon
ARM: dts: dra71-evm: Add VBUS GPIO to USB1/USB2 extcon
ARM: dts: dra7-evm: Add extcon to USB2 port
...
Signed-off-by: Olof Johansson <olof@lixom.net>
-------------------------------------
* DA850 now uses clocks from device-tree
* DA850 EVM gains LCD (with backlight) and SATA support
* Lego Mindstorms gains bluetooth support
* DSP reset control support on DA850
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6E7c
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.19/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
DaVinci Device-Tree updates for v4.19
-------------------------------------
* DA850 now uses clocks from device-tree
* DA850 EVM gains LCD (with backlight) and SATA support
* Lego Mindstorms gains bluetooth support
* DSP reset control support on DA850
* tag 'davinci-for-v4.19/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: Add power-domains to CPPI 4.1 node
ARM: davinci: dts: add a reset control to the dsp node
ARM: davinci: dts: make psc0 a reset provider
ARM: dts: da850-lego-ev3: Add Bluetooth nodes
ARM: dts: da850: Add power-domains to PWM nodes
ARM: dts: da850: Add clocks
dt-bindings: timer: new bindings for TI DaVinci timer
ARM: dts: da850-evm: Enable LCD and backlight
ARM: dts: da850-evm: Enable SATA port
Signed-off-by: Olof Johansson <olof@lixom.net>
for 4.19, please pull the following:
- Clement adds ethernet aliases to the Cygnus DTS include file such that
a DT aware bootloader such as u-boot can properly insert MAC addresses
- Mohamed adds a Device Tree node for the HWRNG found on Cygnus SoCs
- Vivek migrates all the BCM5301x (Northstar) Device Tree sources to use
the proper USB 3.0 PHY representation using its parent MDIO bus.
Vivek also completes the Linksys EA9500 Device Tree by adding support
for LEDs, internal and external switches.
- Rafal adds the ARM architected timer to the BCM53573 Device Tree
include file.
- Eric adds the Performance Monitoring Unit to the BCM2837 DTS include
file since it was absent before
- Boris adds the BCM283x transposer block to the Device Tree
- Stefan adds the Raspberry Pi Compute Module (CM1) Device Tree include
and sources.
-----BEGIN PGP SIGNATURE-----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=lRBW
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.19/devicetree' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 4.19, please pull the following:
- Clement adds ethernet aliases to the Cygnus DTS include file such that
a DT aware bootloader such as u-boot can properly insert MAC addresses
- Mohamed adds a Device Tree node for the HWRNG found on Cygnus SoCs
- Vivek migrates all the BCM5301x (Northstar) Device Tree sources to use
the proper USB 3.0 PHY representation using its parent MDIO bus.
Vivek also completes the Linksys EA9500 Device Tree by adding support
for LEDs, internal and external switches.
- Rafal adds the ARM architected timer to the BCM53573 Device Tree
include file.
- Eric adds the Performance Monitoring Unit to the BCM2837 DTS include
file since it was absent before
- Boris adds the BCM283x transposer block to the Device Tree
- Stefan adds the Raspberry Pi Compute Module (CM1) Device Tree include
and sources.
* tag 'arm-soc/for-4.19/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Add support for Linksys EA9500
ARM: dts: BCM53573: Add architected timer
ARM: dts: BCM5301X: Make USB 3.0 PHY use MDIO PHY driver
ARM: dts: cygnus: enable iproc-hwrng
ARM: dts: cygnus: add ethernet0 alias
ARM: dts: bcm283x: Add Transposer block
ARM: dts: bcm283x: Add the PMU to the devicetree.
ARM: dts: add Raspberry Pi Compute Module and IO board
Signed-off-by: Olof Johansson <olof@lixom.net>
as conversion of rk3288 to OPPv2 to facilitate the addition of
missing cpu-cooling-device properties.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAltGCwUQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgVk2CACbnXTVeS+u/fwgDHA1imCfAjQEGt25yFmV
Yv9GYkFLwvE0dg54Law3u1yYosXuO64Eu3fLZSrOYpI9CadWgMCq+H0rdg3f2Z2Y
mbdW7Ey26U7zGvZkQaEKS7OrUmf5ZQ6TEO70+miQ8Az2G4iEs5fDVRwRN3mJPzV8
Sf5c/dZSQUDD1brKvpTAWpZ4zo4Gx44yBu9DOF6ro9v7h9NNg6Oi6Uuc748Kd8+0
GZLXotcuxPRo2nPpwZYEVgdxHCVkfXezngC0/jc58aYJWbSnqyibrg228siVBDZe
e3p5LyRsn+ALdL5ol1CwRzhShlDIj1GIwZ+jAR87U0hHBT0R6Wdh
=de2o
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
SPDX conversion for existing Rockchip devicetree files as well
as conversion of rk3288 to OPPv2 to facilitate the addition of
missing cpu-cooling-device properties.
* tag 'v4.19-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add missing cooling device properties for CPUs on rk3288
ARM: dts: rockchip: convert rk3288 to operating-points-v2
ARM: dts: rockchip: Add missing cooling device properties for CPUs on rk322x
ARM: dts: rockchip: use SPDX-License-Identifier
Signed-off-by: Olof Johansson <olof@lixom.net>
MAC is connected to a PHY in RGMII mode.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add Ethernet support (Synopsys MAC IP 4.20a) on stm32mp1 SOC.
Enable feature supported by the stmmac driver, such as TSO.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
System configuration controller is mainly used to manage
the compensation cell and other IOs and system related
settings.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds SPI1 support on stm32mp157c-ev1 board.
SPI1 is available on GPIO expansion connector but kept disabled
so these pins can be used as GPIOs by default.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
stm32mp157c has an ADC block with two physical ADCs.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB OTG HS on stm32mp157c-ev1 in Peripheral mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for USB OTG HS on STM32MP157C SoC.
USB OTG HS controller is based on DWC2 controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB Host (USBH) EHCI controller on stm32mp157c-ev1.
As a hub is used between USBH and USB connectors, no need to enable
USBH OHCI controller: all low- and full-speed traffic is managed by the
hub.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The AM3517 has a different OTG controller location than the OMAP3,
which is included from omap3.dtsi. This results in a hwmod error.
Since the AM3517 has a different OTG controller address, this patch
disabes one that is isn't available.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Libretech ALL-H3-CC has a high density connector for attaching
an eMMC module. The module form factor and connection is specific
to Libretech, and has provisions for split vmmc/vqmmc (core and I/O)
voltage supplies, but this board does not wire the vqmmc side. The
H2+/H3/H5 SoCs do not support alternate I/O voltages for eMMC either.
Only 3.3V is supported. A specific module that ties vqmmc to vmmc,
with both at 3.3V, must be used.
Given that a) eMMC is not designed to be hotplugged, b) power is
always provided on the pins, and c) MMC controllers can deal with
missing cards, we can enable this by default. If a module is attached
it will be picked up by the system.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Banana Pi M2 Zero board has a SY8113B regulator, which is controlled via
GPIO and capable of outputing 1.1V when the PL1 GPIO is set to output 0
or 1.1V when the PL6 GPIO is set to input or output 1, and the output is
the power supply of the ARM cores in H3 SoC.
Add the device tree node of this regulator and set the cpu's cpu-supply
property to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add a label for the PMU node so that the board dts may be able to
pass the 'secure-reg-access' property like this:
&pmu {
secure-reg-access;
};
This also makes it consistent with the PMU node in imx6qdl.dtsi
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX53 Reference Manual add an entry for the
'tigerp' region in the device tree.
This is needed for accessing the ARM_GPC register to set the
DBGEN bit, so that the debug clocks can be turned on.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX51 Reference Manual add an entry for the
'tigerp' region in the device tree.
This is needed for accessing the ARM_GPC register to set the
DBGEN bit, so that the debug clocks can be turned on.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX51 Reference Manual the M4IF register region
starts at 0x83fd8000 and has a 4kB address range.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Sergey Lapin <sergey.lapin@cogentembedded.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6UL has GPIO clock gates in CCM CCGR, add
clock property for GPIO driver to make sure all
GPIO banks work as expected.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With old bindings imx_gpc_onecell_data always sets num_domains to 2 so
the DISPMIX domain can't actually be referenced. The pd is still defined
and pm core shuts it down as "unused" so display can't work.
Fix this by converting to new gpc bindings by adding pgc nodes and
referencing the newly-defined &pu_disp domain from &lcdif.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SX has a 16KB always-on ocram bank called
ocram_s, enable it as another mmio sram.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
100/200MHz states for USDHC3 are not required since the SoC
does not support modes faster than DDR52 for the on board eMMC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VDDD is connected to VGEN4 of the PF0100. This rail should only
run at 1.8V since there are multiple consumer and they all
expect the rail to be at 1.8V.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the 2.5V regulator, it does not exist. There is 3.3V and
3.3V_AUDIO provided to the module through the edge connector,
model those as fixed regulators like we use to do in other
Colibri device trees. The SGTL5000 uses 3.3V_AUDIO as VDDA. Note
that the driver derives the analog ground voltage (VAG) from this
supply. The new value should allow higher output swings before
clipping occurs. Refer to the SGTL5000 datasheet for details.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The fixed 1.8V regulator is not used, and there is in fact no
fixed 1.8V regulator on the module. Remove it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the disable-wp to indicate that Apalis and Colibri iMX6 do not
make use of the native write-protect signal available on the i.MX 6
SoCs. This prevents warnings:
mmc0: host does not support reading read-only switch, assuming write-enable
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use no-1-8-v device tree property to indicate that the board does
not support 1.8V signaling. The property voltage-ranges seems not
appropriate in our case since we do not have level shifters in
place.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the 3.3V main supply on the carrier board. Currently as a fixed
supply since not all consumer are modeled yet. This gets also rid of
some missing supply warnings.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 654f2b937b ("crypto: caam - allow retrieving 'era' from
register") the CAAM driver is capable of obtaining the era version by
reading the appropriate CAAM registers, so let the CAAM driver discover
the era version in run-time instead of hardcoding such information in the
device tree.
According to Documentation/devicetree/bindings/crypto/fsl-sec4.txt the
'fsl,sec-era' is an optional property and this can be safely removed
now.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The change adds a number of basic peripherals found on i.MX31 SoC:
* GPIO controllers,
* I2C master controllers,
* SPI master controllers,
* ATA controller,
* SDHC controllers,
* RTC, watchdog and PWM contollers,
* SDMA,
* IRAM,
* NAND and WEIM controllers on EMI.
The added controller devices were tested on Freescale i.MX31 powered
LogicPD Lite SoM and baseboard.
DMA functionality was tested on SDHC and SPI controllers so far,
thus dmas properties are added to those device nodes only.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a SRAM controller node for the H3, with support for the C1
SRAM region that is shared between the Video Engine and the CPU.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the compatible and commit prefix]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a SRAM controller node for the A23 and A33, with support for
the C1 SRAM region that is shared between the Video Engine and the CPU.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the prefix and the compatibles]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for the A20 platform. The region is shared
between the Video Engine and the CPU.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the SRAM C size]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for sun5i-based platforms. The region is shared
between the Video Engine and the CPU.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the SRAM C size to take the C2 and C3 SRAM into account]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun7i-a20 dtsi to use the most qualified compatibles
for the system-control block (previously named SRAM controller) as well
as the SRAM blocks. The sun4i-a10 compatibles are kept since these
hardware blocks are backward-compatible.
The node name for system control is also updated to reflect the fact that
the controller described is really about system control rather than SRAM
control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun5i dtsi to use the most qualified compatibles for
the system-control block (previously named SRAM controller) as well as
the SRAM blocks.
The node name for system control is also updated to reflect the fact that
the controller described is really about system control rather than SRAM
control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Removed the A10 compatible for the driver]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun4i-a10 dtsi to use the new compatible for the
system-control block (previously named SRAM controller) instead of
the deprecated one.
The node name is also updated to reflect the fact that the controller
described is really about system control rather than SRAM control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Amended the commit message]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
R40 has 4 TCONs, but only 2 of them can receive some kind of output at
the same time. Let's disable them by default, so only those which are
really connected on board can be enabled in board dts file.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Current R40 is missing some graph connections between TCON TOP and
TCONs.
Add them.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A83T and R40 TCON TV are very similar. However, R40 TCON TV is wired
differently, which makes it incompatible with A83T TCON TV.
Because of that, remove fallback A83T TCON TV compatible.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
sun4i-drm DT binding, second paragraph of the first section says:
For all connections between components up to the TCONs in the display
pipeline, when there are multiple components of the same type at the
same depth, the local endpoint ID must be the same as the remote
component's index.
Add mixer ids in R40 DT as mandated by DT binding.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add support for the MCAN peripheral which supports both classic
CAN messages along with the new CAN-FD message.
Add MCAN node to evm and enable it with a maximum datarate of 5 mbps
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti-sysc driver provides support for manipulating the idle modes
and interconnect level resets.
Add the generic interconnect target module node for MCAN to support
the same.
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MCAN is clocked by H14 divider of DPLL_GMAC. Unlike other
DPLL dividers this DPLL_GMAC H14 divider is controlled by
control module. Adding support for these clocks.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the power-domains property to CPPI 4.1 node.
The CPPI 4.1 DMA driver uses pm_runtime to manage the clocks,
so it needs this property in order to find and enable the clock
properly.
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This enables the on-module ONFI conformant NAND flash.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add basic controller device tree node to be extended by
individual boards. Use the assigned-clocks mechanism to set
NDFLASH clock to a sensible default rate of 150MHz.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Colibri-T20 can come in 256 MB RAM (with 512 MB NAND) or 512 MB RAM
(with 1024 MB NAND) flavors. Both of them will use the same DTSI
expecting the bootloader to do the fixup of /memory node. However in
case it does not happen, let's stay on safe side by limiting the memory
to 256 MB for both versions of Colibri-T20.
Rename to remove the unnecessary memory size from the device tree file
name. While at it, also follow the typical Toradex SoC, module, carrier
board hierarchy.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove unneeded address/size cells properties and unit addresses to fix
DTC warnings like:
arch/arm/boot/dts/tegra30-apalis-eval.dtb: Warning (unit_address_vs_reg):
/i2c@7000d000/stmpe811@41/stmpe_touchscreen@0: node has a unit name, but no reg property
arch/arm/boot/dts/tegra30-apalis-eval.dtb: Warning (avoid_unnecessary_addr_size):
/i2c@7000d000/stmpe811@41: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a generic /memory node in each Tegra DTSI (with empty reg property,
to be overidden by each DTS) and set proper unit address for /memory
nodes to fix the DTC warnings:
arch/arm/boot/dts/tegra20-harmony.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
The DTB after the change is the same as before except adding
unit-address to /memory node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the usage of skeleton.dtsi because it was deprecated since commit
9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as deprecated").
It also allows later to fix DTC warnings for missing unit name in
/memory nodes.
Compiled DTBs are the same as before this commit.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This pull request brings in a board DT for the Raspberry Pi Compute
Module and its I/O board, the Pi3's PMU node, and the display's
transposer block.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's a standard ARM architected timer that was simply missed when
initially adding this .dtsi file.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Currently, the USB 3.0 PHY in bcm5301x.dtsi uses platform driver which
requires register range "ccb-mii" <0x18003000 0x1000>. This range
overlaps with MDIO cmd and param registers (<0x18003000 0x8>).
Essentially, the platform driver partly acts like a MDIO bus driver,
hence to use of this register range.
In some Northstar devices like Linksys EA9500, secondary switch is
connected via external MDIO. The only way to access and configure the
external switch is via MDIO bus. When we enable the MDIO bus in it's
current state, the MDIO bus and any child buses fail to register because
of the register range overlap.
On Northstar, the USB 3.0 PHY is connected at address 0x10 on the
internal MDIO bus. This change moves the usb3_phy node and makes it a
child node of internal MDIO bus.
Thanks to Rafał Miłecki's commit af850e14a7 ("phy: bcm-ns-usb3: add
MDIO driver using proper bus layer") the same USB 3.0 platform driver
can now act as USB 3.0 PHY MDIO driver.
Tested on Linksys Panamera (EA9500)
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In order to avoid Linux generating a random mac address on every boot,
add an ethernet0 alias that will allow u-boot to patch the dtb with
the MAC address.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The transposer block is allowing one to write the result of the VC4
composition back to memory instead of displaying it on a screen.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This only probes on arm64 so far, but hopefully that driver will be
generalized soon.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
CAN2 currently fails on probe as follows:
mcp251x spi1.1: Probe failed, err=19
Fix this by enabling input on pin mux of resp. SPI4 pins.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On all versions of Tegra30 Cardhu, the reset signal to the NXP PCA9546
I2C mux is connected to the Tegra GPIO BB0. Currently, this pin on the
Tegra is not configured as a GPIO but as a special-function IO (SFIO)
that is multiplexing the pin to an I2S controller. On exiting system
suspend, I2C commands sent to the PCA9546 are failing because there is
no ACK. Although it is not possible to see exactly what is happening
to the reset during suspend, by ensuring it is configured as a GPIO
and driven high, to de-assert the reset, the failures are no longer
seen.
Please note that this GPIO is also used to drive the reset signal
going to the camera connector on the board. However, given that there
is no camera support currently for Cardhu, this should not have any
impact.
Fixes: 40431d16ff ("ARM: tegra: enable PCA9546 on Cardhu")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PandaBoard has a user button connected to GPIO. On the ES this is connected
to GPIO 113, on all the other Panda editons this is GPIO 121.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are a few peripherals that generate some extra noise when they
don't have a regulator assigned to them. This patch assigns them to
their actual tps65023 regulator 'vdd_io_reg' (VDCDC2).
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hook up Memory Client reset of the Video Decoder to the decoders DT node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Hook up Memory Client reset of the Video Decoder to the decoders DT node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This DTS file have initial support Samsung SGH-T959P phone,
also known as Samsung Galaxy S 4G or fascinate4g. It belongs to Samsung
Aries devices family.
Initial version have support for:
- sdcard
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This DTS file have initial support Samsung Galaxy S phone, also known as
i9000. It belongs to Samsung Aries devices family.
Initial version have support for:
- sdcard
- internal memory
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This DTS file have initial support Samsung Aries based phones.
Initial version have support for:
- sdcard
- internal memory (present only on non 4g variant)
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Adds missing interrupt-controller property to gph2 block,
to silence following warnings during build:
/soc/pinctrl@e0200000/gph2: Missing interrupt-controller or interrupt-map property
It's reguired by Samsung Aries boards, an S5PV210 based
Samsung Galaxy S (i9000) and Galaxy S 4G phones, which are added in next patches.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commit 2f28e4c24b (thermal: armada: Clarify control registers
accesses) introduced the new thermal binding. The new binding extends
the second registers field size to 8. Switch to the new binding to fix
thermal reading values. Without this change the fix for errata #132698
introduced in commit 8c0b888f66 (thermal: armada: Change sensors trim
default value) has no effect.
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Few dts fixes for regressions for various SoCs and
devices for touchscreen wake, dra7 USB quirk, pinmux
for beaglebone mmc, and emac clock.
Also included is a change for ti-sysc to use kcalloc
that Kees wanted to get into v4.18 as that's the last
one he wanted to fix for improved defense against
allocation overflows.
-----BEGIN PGP SIGNATURE-----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=H1MU
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap for v4.18-rc cycle
Few dts fixes for regressions for various SoCs and
devices for touchscreen wake, dra7 USB quirk, pinmux
for beaglebone mmc, and emac clock.
Also included is a change for ti-sysc to use kcalloc
that Kees wanted to get into v4.18 as that's the last
one he wanted to fix for improved defense against
allocation overflows.
* tag 'omap-for-v4.18/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: Fix am3517 mdio and emac clock references
ARM: dts: am335x-bone-common: Fix mmc0 Write Protect
bus: ti-sysc: Use 2-factor allocator arguments
ARM: dts: dra7: Disable metastability workaround for USB2
ARM: dts: am437x: make edt-ft5x06 a wakeup source
Signed-off-by: Olof Johansson <olof@lixom.net>
The enabling of the EMAC was reverted as there was an issue on how
to handle the integrated PHY and it was getting close to the release
window (fe45174b72 ("arm: dts: sunxi: Revert EMAC changes")).
When a solution was found, then the changes were restored in
4b236a0fe5 ("arm: dts: sunxi: h3/h5: Restore EMAC changes") and
4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)").
Unfortunately enabling for the Beelink X2 was missed.
This reverts partially commit 6b0e06df5c (Revert "ARM: dts:
sun8i: h3: Enable dwmac-sun8i on the Beelink X2")
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
- A couple of imx defconfig updates selecting USB ULPI support to fix
a regression seen with USB driver, which is caused by commit
03e6275ae3 ("usb: chipidea: Fix ULPI on imx51").
- A fix on imx51-zii-rdu1 board touchscreen pinctrl setting, which
causes an interrupt storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbO3x0AAoJEFBXWFqHsHzODGkIAIIJFPOWBYHyxAVLAtqpNTt7
+Yggu9LGe7rhspT+Hi2DocKIEj1Z11x49KJCqxwrEHg+7xyax6d78b1iclCHLRlr
S9jxulipzkBs/neebrhh6cyF8sxA7TPUgXtEMdRJwYygUoZhe9hngTO3jv+xoDky
l1l9zH9gAlAQA1cxN6Z4ZWYDkNS0mYK3e1VzaeyCXsq5GJ1Vm5Qw1ooTE5DL3K1g
5B2Hw057DJvcSwOhIVir/MQR8sAWj1sKYdsCouxrO/ThEyofEAtfn22romcPaGPW
WBOuTNrOrMy6O/+ndMBNJBXeGt1tONL2cjLbrpffaXJYq6m/56efsee9u1u18Vg=
=4Agh
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.18, round 2:
- A couple of imx defconfig updates selecting USB ULPI support to fix
a regression seen with USB driver, which is caused by commit
03e6275ae3 ("usb: chipidea: Fix ULPI on imx51").
- A fix on imx51-zii-rdu1 board touchscreen pinctrl setting, which
causes an interrupt storm.
* tag 'imx-fixes-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v4_v5_defconfig: Select ULPI support
ARM: imx_v6_v7_defconfig: Select ULPI support
ARM: dts: imx51-zii-rdu1: fix touchscreen pinctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently the following DTC warnings are seen with W=1:
arch/arm/boot/dts/imx51-babbage.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
Fix it by moving the USB PHY nodes outside of simple-bus and drop the
unneeded unit-address, which matches the bindings documentation
at Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
While at it rename the USB PHY node to usbphy1 for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (like clocks, supply, clock latency) as
well to make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous patch removed OMAP clock aliases that were perceived
to be unnecessary. Unfortunately, it broke the ethernet on the
am3517-evm. This patch enables the MDIO clock and EMAC clock.
Fixes: 0ed266d7ae ("clk: ti: omap3: cleanup unnecessary clock aliases")
Cc: stable@vger.kernel.org #4.16+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM3517-evm has a single USB Host port connected to hsusb1.
This patch enables that USB port.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DT specifications do not allow the underscore character in alias names.
Replace all underscores in alias names by dashes.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the Bluetooth on the wl1271 available in some models
of the AM3517-SOM from Logic PD.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Certain models of the AM3517 SOM from Logic PD come with an
integrated WL1271 WiFi. This patch enables the WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The tsadc is used to read various voltages on the board, so enable it
to be able to read these voltages from userspace.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the label for all LEDs, we made a mistake setting the label names on
all LEDs, where says green should say red, and viceversa, where says red
should be green.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
audio-graph-card is recommended for audio bindings. Let's change to it and
improve the support by adding the Amplifier configuration and the clock
enable control.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Production hardware will go with the DS1339 RTC chip, so replace the old
for the new one and also add the nIRQ pin to be able to properly wakeup
the system from suspend.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board can be either a host, or a peripheral, so set the controller as
OTG mode to reflect this.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the pins used by the LCD controller, the panel-info and display-timings
information for the MIDAS displays connected to the board. There are
two displays in the board, and these, are connected to the LCD controller
through a FPGA, so the timings and the resolution is what expects the FPGA,
not the MIDAS displays.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
phy-phandle is now a preferred method to reference a PHY device. The new
method also allows you to specify a reset gpio which is required for
this board.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the backlight nodes to improve the support and describe
better how hardware is done. The changes done were:
* Use PWM_POLARITY_INVERTED instead of the hardcoded number.
* Add pinctrl configuration.
* Add the enable gpio definition.
* Add the power supply definition.
* Add more brightness levels.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default value of 5ms will use GPIO hardware based debounce clocks
that will keep L4PER from idling consuming about extra 30mW.
Use a value of 10ms that is above the hardware debounce maximum of
7.95ms forcing software based debouncing.
This allows droid4 to enter PER retention during idle as long as UARTs
are idled and USB modules unloaded or unbound.
Note that there seems to be a pending issue with having droid 4 enter core
retention during idle where GPIO bank 1 needs to be reset late after init
for some reason to not block core retention. In addition to that, we are
also missing GPIO related PM runtime calls for omap4 that will be posted
separately.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By reconfiguring few GPIOs in the dts file we can make duovero parlor
hit retention during idle:
1. Let's a larger debounce value for gpio-keys
This will then make gpio-keys use software debounce and the GPIO
debounce clock is not enabled.
2. Let's allow WLAN suspend for mwifiex
This can be done just by adding keep-power-in-suspend.
3. Let's reconfigure smsc911x driver to use GPIO edge interrupt
This will allow using NFSroot while the system idles, and the kernel
has quite a few dts files with "smsc,lan9115" compatible using edge
interrupts.
Then to have the system hit core retention during idle, the UARTs
needs to be idled and USB modules need to be unloaded or unbound.
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wl1835mod.pdf data sheet says this pretty clearly for WL_IRQ line:
"WLAN SDIO out-of-band interrupt line. Set to rising edge (active high)
by default."
And it seems this interrupt can be optionally configured to use falling
edge too since commit bd763482c8 ("wl18xx: wlan_irq: support platform
dependent interrupt types").
On omap4, if the wlcore interrupt is configured as level instead of edge,
L4PER will stop doing hardware based idling after ifconfig wlan0 down is
done and the WL_EN line is pulled down.
The symptoms show up with L4PER status registers no longer showing the
IDLEST bits as 2 but as 0 for all the active GPIO banks and for
L4PER_CLKCTRL. Also the l4per_pwrdm RET count stops increasing in
the /sys/kernel/debug/pm_debug/count.
While there is also probably a GPIO related issue that needs to be
still fixed, this change gets us to the point where we can have L4PER
idling.
I'm guessing wlcore was at some point configured to use level interrupts
because of edge handling issues in gpio-omap. However, with the recent
fixes to gpio-omap the edge interrupts seem to be working just fine.
Let's change it for all omap boards with wlcore interrupt set as level.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com updated comments a bit for gpio issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has USB VBUS detection available over GPIO. Plug it to
extcon node of USB1 and USB2 ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has USB VBUS detection available over GPIO. Plug it to
extcon node of USB1 and USB2 ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both ports on the dra7-evm and related boards can be used
as dual-role ports. Although we don't enable dual-role mode
for USB2 port let's add the necessary extcon bits to it.
Move the common portion of extcon_usb2 into dra7-evm-common.dtsi
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dual-role support was added in v4.12. We should be using
it for USB2 port on the am57xx-idk.
Cc: <stable@vger.kernel.org> [4.16+]
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, supply, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, supply, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to i.MX6 datasheet, the LDO_1P1's typical
programming operating range is 1.0V to 1.2V, and
the LDO_2P5's typical programming operating range
is 2.25V to 2.75V, correct LDO_1P1 and LDO_2P5's
regulator range settings for i.MX6 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per Documentation/process/license-rules.rst the SPDX notation for
header file should be /* */ style, so fix it accordingly.
Fixes: 9f30b6b1a9 ("ARM: dts: imx: Add basic dtsi file for imx6sll")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The AM3517-EVM uses a TPS65023 PMIC. This is already defined
by: compatible = "ti,tps65023"
There doesn't seem to be a need to have each regulator in the
PMIC with the 'compatible = "regulator-fixed"' since each
regulator has a min and max setting.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
i.MX6ULL has different operating ranges than i.MX6UL so add the
operating points for the i.MX6ULL and remove them from board device
trees. A 25mV offset is added to the minimum allowed values like for the
i.MX6UL.
The valid frequencies are now selected by the cpufreq driver according
to ratings stored in fuses since commit 0aa9abd4c2 ("cpufreq: imx6q:
check speed grades for i.MX6ULL")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mainline Commit b74c2b21e1 added the pinmux
settings for mmc1, however this pin (0x9a0) is routed to P9_42 on the cape
header. Thus any BeagleBone cape that utilizes P9_42 triggers mmc0's Write
Protect.
Fixes: b74c2b21e1 ("ARM: dts: am33xx: Add pinmux data for mmc1 in
am335x-evm, evmsk and beaglebone")
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Faiz Abbas <faiz_abbas@ti.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This was fixed in
645a397, so correct the RDU1 DT to apply the inversion to the
correct axis.
Tested on Zii RDU1 00-5105-30 rev B
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This renames usbphy nodes 2 & 3, so that they follow the same
format as usbphy node 0 & 1 from imx53.dtsi.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add information about 3V3 power rail to avoid kernel warnings,
that dummy regulators have been added.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pinctrl_usbh1reg defines pinmux setting for reset GPIO used by
usbh1phy, but is not referenced by that node. Fix that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing property (clock latency) as well to make it all
work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The davinci-rproc driver will soon use the reset framework. Add the
resets property to the dsp node in da850.dtsi.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The psc driver registers with the reset framework as a provider. Add
the #reset-cells property to the psc0 node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Disable the metastability workaround for USB2. The original
patch disabled the workaround on the wrong USB port.
Fixes: b8c9c6fa20 ("ARM: dts: dra7: Disable USB metastability workaround for USB2")
Cc: <stable@vger.kernel.org> [4.16+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On i.MX6SLL EVK board, SD3 slot can be used for
WiFi and other SD accessories, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RAVE SP found on RDU2 implements power button control compatible with
the rave-sp-pwrbutton driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RAVE SP found on RDU2 implements backlight control compatible with the
rave-sp-backlight driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ZII's RDU1s come with up to 3 EEPROMs attached to RAVE SP. Add
corresponding nodes to make them availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The hog pinctrl hog is meant for pins that do not have an
associated driver.
The MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK pin is the one that
provides the MCLK signal to the SGTL5000 codec, so a
better represenation is to move it under the codec node.
While at it, change the pinctrl value from 0x80000000 to the
POR reset value of register IOMUXC_SW_PAD_CTL_PAD_GPIO_0.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sahara crypto block on i.MX51 has the same IP version as
the one on i.MX53.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wake-up pin is pulled low with 100kOhm on the carrier board.
The current configuration of 100kOhm pull-up caused lots of
interrupts, especially during boot up. Make sure the pin is at a
reasonable level at startup by pulling it low on SoC side too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Muxing the card detect only in the carrier board device tree
overwrites the USDHC muxing in the module level device tree.
Move card detect to the module level device tree since this
is also a default pinout of the Colibri standard. If a carrier
board requires a different setting it still can overwrite the
nodes in the carrier board specific device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Do not rely on reset/boot defaults and use a default GPIO setting
with pull-up enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This makes it possible to enable earlycon for debugging by just passing
an empty "earlycon" argument on the kernel command-line.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the i.MX50 Reference Manual, the SoC features one USB OTG
and one host controller. Remove the non-existent instances from the
DTS which probably got initially copied from the mx53 DTS.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
iMX50 pin mux options for pads KEY_COL2 and KEY_COL3 allow muxing the same
KEY_COL instances as the pad name. Fix typos shifting KEY_COL instances.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pinctrl settings were incorrect for the touchscreen interrupt line, causing
an interrupt storm. This change has been tested with both the atmel_mxt_ts and
RMI4 drivers on the RDU1 units.
The value 0x4 comes from the value of register IOMUXC_SW_PAD_CTL_PAD_CSI1_D8
from the old vendor kernel.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Fixes: ceef0396f3 ("ARM: dts: imx: add ZII RDU1 board")
Cc: <stable@vger.kernel.org> # 4.15+
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently when trying to use the 'devmem' tool to read/write
registers the following bus error is observed:
[ 82.689185] Unhandled fault: external abort on non-linefetch (0x1018) at 0xb6ff10c4
[ 82.697071] pgd = (ptrval)
[ 82.699920] [b6ff10c4] *pgd=a87c5831, *pte=73fa8383, *ppte=73fa8a33
Bus error
Add the aipstz nodes, so that the following function from
imx51_dt_init() can work properly:
imx_aips_allow_unprivileged_access("fsl,imx51-aipstz");
After adding these nodes, 'devmem' tool can work correctly,
which is very useful for debugging purposes.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This was removed in commit 5eaeaccdae ("ARM: dts: imx7d-sdb: Pass
'enable-gpios' and 'power-supply' properties") with a note claiming that
GPIO1_IO01 is connected to a pin labeled as "PWREN" on the connector.
Despite that label this pin does actually work as a PWM controlling
brightness. So restore pwm functionality.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use sdhci-omap programming model based on the generic sdhci
library for programming the MMC/SD controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add "vqmmc-supply" property for mmc0/mmc1 to indicate the supply connected
to the IO lines. Also add dt node for ldo1 regulator required for mmc1
vqmmc-supply.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
and fixes interrupt property for DA850 SoC GPIO as defined in
device-tree.
Both of these are not introduced with v4.18 merge but have
existed prior.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AENA
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
This fixes polarity of SD card write-protect pin on DA850 EVM
and fixes interrupt property for DA850 SoC GPIO as defined in
device-tree.
Both of these are not introduced with v4.18 merge but have
existed prior.
* tag 'davinci-fixes-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: Fix interrups property for gpio
ARM: davinci: board-da850-evm: fix WP pin polarity for MMC/SD
Signed-off-by: Olof Johansson <olof@lixom.net>
Also fix the documentation for these bindings.
The DMA properties have to be passed in the ssp users for now.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The NAND driver looks for a clock named "core" and falls back to a pdev
clock that has a wrong rate if not set.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
So it can be referenced and filled with more details from board files.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The current device-tree description of the SolidRun Armada 38x platforms
has been successfully tested with production systems.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Jon Nettleton <jon@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The SolidRun Armada 388 SOM has the SPI flash populated by default
unless the customer explicitly asks otherwise. Enable support by
default.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The OPPs for the A83T CPU cores were added in v4.17 in commit 2db639d8c1
("ARM: dts: sun8i: a83t: add stable OPP tables and CPUfreq"), but board
level regulator supplies for the CPU clusters were only added for the
TBS-A711 tablet. This means the other A83T boards do not benefit from
voltage scaling, or worse, if the implementation does not scale the
frequency when the voltage is fixed, no benefit at all.
Add board level CPU cluster power supplies to all the A83T development
boards, so they can have proper dynamic CPU voltage and frequency scaling.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Since HDMI can be considered as main output, most capable mixer is
connected to it (mixer0).
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add all entries needed for HDMI to function properly.
Since R40 has highly configurable pipeline, both mixers and both TCON
TVs are added. Board specific DT should then connect them together
trough TCON TOP muxers to best fit the purpose of the board.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
i.MX6SLL uses same SRC module as i.MX51, add "fsl,imx51-src"
compatible string to enable SRC driver to support setting
CPU resume address for cpu-idle and suspend/resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RIoTboard debug uart is connected to serial1.
Add a chosen property in the DTS so OS knows what serial port to use for
the console.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The intc #interrupt-cells is equal to 1. Currently gpio
node has 2 cells per IRQ which is wrong. Remove the additional
cell for each of the interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: 2e38b946dc ("ARM: davinci: da850: add GPIO DT node")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds nodes for describing the Bluetooth chip and connections on
LEGO MINDSTORMS EV3 to da850-lego-ev3.dts.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds the power-domains property to both the ECAP and EHRPWM PWM
nodes. Both have drivers that use pm_runtime to enable the clocks, so
they need this property in order to find and enable the clock properly.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The helios4 is a Armada388 based nas board designed by SolidRun and
based on their SOM. It is sold by kobol.io the dts file came from
https://raw.githubusercontent.com/armbian/build/master/patch/kernel/mvebu-default/95-helios4-device-tree.patch
I added a SPDX license line to match the clearfog it says it was based
on and a compatible line for "kobol,helios4"
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Remove the unused bus-num node and change num-chipselect
to num-cs to match SPI bindings.
Cc: stable@vger.kernel.org
Fixes: f2d6f8f817 ("ARM: dts: socfpga: Add SPI Master1 for Arria10 SR chip")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds dt bindings to enable netcp network driver on K2G
ICE boards. This consists of enabling bindings for NSS qmss, pktdma,
2u ethss, mdio, pinmux and netcp devices as well as DP83867 phy.
EVM hardware spec recommends to add 0.25 nsec delay in the tx direction
and 2.25 nsec delay in the rx direction for internal delay in the clock
path to be on the safer side.
The board straps RX_DV/RX_CTRL pin of on board DP83867 phy in mode 1.
The phy data manual disallows this. Add ti,dp83867-rxctrl-strap-quirk
in the phy node to allow software to enable the workaround suggested for
this incorrect strap setting. This ensures proper operation of this PHY.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
This patch add dt bindings to support network driver based on
Network Sub System (NSS) found on k2g SoC. This consists of
bindings for netcp node, nss qmss , pktdma, cpsw 2u version
of ethss and mdio.
In order to support transitioning between non-promiscuous
and promiscuous modes in K2G's ethernet switch, netcp ALE
needs to be enabled. Therefore this patch enables K2G's
netcp ALE for that purpose.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
This adds clock provider nodes for da850 and wires them up to all of the
devices.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for RTC (Real Time Clock) to STM32MP157C SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Remove no longer needed samsung thermal properties.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Secondary CPUs should have the same information in DeviceTree as booting
CPU from both correctness point of view and for possible hotplug
scenarios.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, OPP, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add activation of the Controller Area Network m_can on stm32mp157c-ev1
board.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for the Controller Area Network m_can to STM32MP157C SoC.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
To fit with latest rtc driver updates, rtc st,syscfg property must contain
the control register offset of pwrcfg and the mask corresponding to the
DBP (Disable Backup Protection) bit.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
To fit with latest rtc driver updates, rtc st,syscfg property must contain
the control register offset of pwrcfg and the mask corresponding to the
DBP (Disable Backup Protection) bit.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
4.18, please pull the following:
- Ray fixes the I2C and PCIe interrupt types for the Cygnus SoC
- Florian fixes the I2C and PCIe interrupts for the Northstar
(BCM5301x), Northstar Plus and Hurricane 2 SoCs
-----BEGIN PGP SIGNATURE-----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=0JyZ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.18/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
4.18, please pull the following:
- Ray fixes the I2C and PCIe interrupt types for the Cygnus SoC
- Florian fixes the I2C and PCIe interrupts for the Northstar
(BCM5301x), Northstar Plus and Hurricane 2 SoCs
* tag 'arm-soc/for-4.18/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: Cygnus: Fix PCIe controller interrupt type
ARM: dts: Cygnus: Fix I2C controller interrupt type
ARM: dts: BCM5301x: Fix i2c controller interrupt type
ARM: dts: HR2: Fix interrupt types for i2c and PCIe
ARM: dts: NSP: Fix PCIe controllers interrupt types
ARM: dts: NSP: Fix i2c controller interrupt type
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix i.MX6SX PCIe MSI interrupt number, so that MSI IRQs can be
properly propagated to the upstream interrupt controller.
- Fix GPCv2 MIPI/PCIe/USB_HSIC's PGC offset. The values in Reference
Manual are incorrect.
- Correct SDMA setting for i.MX6Q SPI5 device to fix the issue, that
the SPI controller RX FIFO was not empty after a DMA transfer, and
the driver gets stuck in the next PIO transfer when reading one word
more than expected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbKLcnAAoJEFBXWFqHsHzO8dMH/ijDSZf172X9jls8iQgcFQ8h
ZAnIj+T23j9L8CTHBx5OLgUxaHYgX410HYvqWuubCNDKv+DMCP+7QNE6v+iSehhT
8sA4dX5296orNb9d5dXyf0XIZ4dA1ljhoZUY6r9DHGFfkIriHwX6HB0zl9EmroAK
mVMGeltfGqPCZ6bH1O6L4oCZNfaOmqBz1f767Es4uxD0IzPg/9BlarqLgASu+op1
1KVFGKY/o4S6QrMxrLxlsrqFUx1DmRQyWxtKYyPlkY6LIHeiJNMCLh9NzW+/qGHf
keycpIjVdlVdZMILDeTju3gszoOmXjq0L1XP9Ityf9OLq53c1Ypsn9npK2ccZNU=
=lalT
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.18:
- Fix i.MX6SX PCIe MSI interrupt number, so that MSI IRQs can be
properly propagated to the upstream interrupt controller.
- Fix GPCv2 MIPI/PCIe/USB_HSIC's PGC offset. The values in Reference
Manual are incorrect.
- Correct SDMA setting for i.MX6Q SPI5 device to fix the issue, that
the SPI controller RX FIFO was not empty after a DMA transfer, and
the driver gets stuck in the next PIO transfer when reading one word
more than expected.
* tag 'imx-fixes-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: fix irq for pcie bridge
soc: imx: gpcv2: correct PGC offset
ARM: dts: imx6q: Use correct SDMA script for SPI5 core
Signed-off-by: Olof Johansson <olof@lixom.net>
- Use correct size for ICU nodes (irq controller) on Armada 7K/8K
- Fix "#cooling-cells" property's name on Synology DS116 (Armada 385)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWwwZggAKCRALBhiOFHI7
1RZ3AJ4wjqNwkBmHpxD5DDQgNcO1WxYhFgCffMYB3qCIdYW6ROiFCs79bq/8Ldc=
=HA77
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.17-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.17 (part 2)
- Use correct size for ICU nodes (irq controller) on Armada 7K/8K
- Fix "#cooling-cells" property's name on Synology DS116 (Armada 385)
* tag 'mvebu-fixes-4.17-2' of git://git.infradead.org/linux-mvebu:
arm: dts: armada: Fix "#cooling-cells" property's name
arm64: dts: marvell: fix CP110 ICU node size
Signed-off-by: Olof Johansson <olof@lixom.net>
The Raspberry Pi Compute Module (CM1) is a SoM which contains a
BCM2835 processor, 512 MB RAM and a 4 GB eMMC. There is also a carrier
board which is called Compute Module IO Board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Make each SoC dtsi use its soc specific PMc compatible string. This solves
a potential issue on at91sam9261 and at91sam9263 when using suspend to RAM
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use the correct IRQ line for the MSI controller in the PCIe host
controller. Apparently a different IRQ line is used compared to other
i.MX6 variants. Without this change MSI IRQs aren't properly propagated
to the upstream interrupt controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: b1d17f68e5 ("ARM: dts: imx: add initial imx6sx device tree source")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two different regulators are defined with the same name and label but
distinct properties.
The first definition was added with the first board dts and the second
was added when upstream added flexcan support.
Looking at schematics it is indeed gpio2 14 connected to the STB pin of
the CAN transceiver so remove the first definition.
The second definition entirely overrides the first so this already
worked and this patch results in no DTB change, just a cleanup.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following sensors are on I2C3 on the baseboard:
* isil,isl29023 light sensor
* fsl,mag3110 magnetometer
* fsl,mma8451 accelerometer
Added under i2cmux/i2c@1 because they're not otherwise accessible.
These are all supported by iio with following configs:
* CONFIG_SENSORS_ISL29018
* CONFIG_MAG3110
* CONFIG_MMA8452
Tested with raw reads from iio sysfs.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- in reg_2p5, fix regulator node name as regulator-2p5v
- remove exctra line
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OV5640 Camera sensor is connected in i.CoreM6 1.5 Quad/Dual MIPI
starter kit.
This patch also move MX6QDL_PAD_GPIO_0__CCM_CLKO1 pinctrl
from i2c3 to ov5640 pinctrl.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This is
fixed now, so correct the RDU2 DT to apply the inversion to the
correct axis.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix PCIe controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
Cygnus SoC
Fixes: cd590b50a9 ("ARM: dts: enable PCIe support for Cygnus")
Fixes: f6b889358a ("ARM: dts: Enable MSI support for Broadcom Cygnus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c controller should be using IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: bb097e3e00 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c and PCIe controllers had an incorrect type which should have
been set to IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The interrupts for the PCIe controllers should all be of type
IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.
Fixes: d71eb94120 ("ARM: dts: NSP: Add MSI support on PCI")
Fixes: 522199029f ("ARM: dts: NSP: Fix PCIE DT issue")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c controller should use IRQ_TYPE_LEVEL_HIGH instead of
IRQ_TYPE_NONE.
Fixes: 0f9f27a36d ("ARM: dts: NSP: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
When using the board files the LCD works, but not with the DT.
This adds enables the original da850-evm to work with the same
LCD in device tree mode.
The EVM has a gpio for backlight regulator and a PWM for dimming
the backlight. The LCD and the vpif display pins are mutually
exclusive, so if using the LCD, do not load the vpif driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The DA850-EVM from Logic PD has a SATA port and the module that went
with the kit supports it as well. This patch enables SATA controller.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, OPP, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[follow conversion to operating-points-v2]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Operating points need to be present in each cpu core using it, not only
the first one. With operating-points-v1 this would require duplicating
this table into each cpu node.
With opp-v2 we can share the same table on all nodes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Add PMIC nodes to Porter and connect CPU DVFS supply. There is
one DA9063L and one DA9210 on Porter, the only difference from
the other boards is that DA9063L is at I2C address 0x5a rather
than 0x58 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, clock-names) as well to make it all
work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, OPP, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
