Looks like our VBIOS/GOP generally fail to turn the DP dual mode adater
TMDS output buffers back on after a reboot. This leads to a black screen
after reboot if we turned the TMDS output buffers off prior to reboot.
And if i915 decides to do a fastboot the black screen will persist even
after i915 takes over.
Apparently this has been a problem ever since commit b2ccb822d3 ("drm/i915:
Enable/disable TMDS output buffers in DP++ adaptor as needed") if one
rebooted while the display was turned off. And things became worse with
commit fe0f1e3bfd ("drm/i915: Shut down displays gracefully on reboot")
since now we always turn the display off before a reboot.
This was reported on a RKL, but I confirmed the same behaviour on my
SNB as well. So looks pretty universal.
Let's fix this by explicitly turning the TMDS output buffers back on
in the encoder->shutdown() hook. Note that this gets called after irqs
have been disabled, so the i2c communication with the DP dual mode
adapter has to be performed via polling (which the gmbus code is
perfectly happy to do for us).
We also need a bit of care in handling DDI encoders which may or may
not be set up for HDMI output. Specifically ddc_pin will not be
populated for a DP only DDI encoder, in which case we don't want to
call intel_gmbus_get_adapter(). We can handle that by simply doing
the dual mode adapter type check before calling
intel_gmbus_get_adapter().
Cc: <stable@vger.kernel.org> # v5.11+
Fixes: fe0f1e3bfd ("drm/i915: Shut down displays gracefully on reboot")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4371
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211029191802.18448-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Try to make bigjoiner pipes less special.
The main things here are that each pipe now does full
clock computation/readout with its own shared_dpll reference.
Also every pipe's cpu_transcoder always points correctly
at the master transcoder.
Due to the above changes state readout is now complete
and all the related hacks can go away. The actual modeset
sequence code is still a mess, but I think in order to clean
that up properly we're probably going to have to redesign
the modeset logic to treat transcoders vs. pipes separately.
That is going to require significant amounts of work.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-9-ville.syrjala@linux.intel.com
The PPS SDP is fed into the transcoder whereas the DSC
block is (or at least can be) per pipe. Let's split these
into two distinct operations in an effort to untagle the
bigjoiner mess where we have two pipes feeding a single
transcoder.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-7-ville.syrjala@linux.intel.com
Disabling planes in the middle of the modeset seuqnece does not make
sense since userspace can anyway disable planes before the modeset
even starts. So when the modeset seuqence starts the set of enabled
planes is entirely arbitrary. Trying to sprinkle the plane disabling
into the modeset sequence just means more randomness and potential
for hard to reproduce bugs.
So it makes most sense to just disable all planes first so that the
rest of the modeset sequence remains identical regardless of which
planes happen to be enabled by userspace at the time.
This reverts commit 84030adb9e.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reanme intel_ddi_fdi_post_disable() to hsw_fdi_disable() and
relocate it next to all the other code dealing with FDI_RX.
intel_ddi.c has now been cleansed of FDI_RX.
In order to avoid exposing intel_disable_ddi_buf() outside
intel_ddi.c we can just open code the DDI_BUF_CTL write. The
enable side already has all that stuff open coded so
this actually is more symmetric. But we do need to remeber
to bring the intel_wait_ddi_buf_idle() call over from
inside intel_disable_ddi_buf().
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-9-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Move the lpt_get_iclkip() call from hsw_crt_get_config()
since that's where we have the lpt_program_iclkip() call
as well.
Tehcnically this isn't perhaps quite right since iCLKIP
is providing the CRT dotclock. So one can argue all of
it should be directly in intel_crt.c. But since the CRT
port is the only one on the PCH sticking it all into the
PCH code seems OK.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-7-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
DKL_TX_LOADGEN_SHARING_PMD_DISABLE doesn't even seem to exist,
also the spec says to skip all loadgen stuff.
The code was dead anyway since it wasn't actually writing the value
anywhere.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006204937.30774-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The 128b/132b channel coding link training uses more straightforward TX
FFE preset values. Reuse voltage tries and max vswing for retry logic.
The delays for 128b/132b are still all wrong, but this is regardless a
step forward.
v2: Fix UHBR rate checks, use intel_dp_is_uhbr() helper
v3:
- Rebase
- Modify intel_dp_adjust_request_changed() and
intel_dp_link_max_vswing_reached() to take 128b/132b into
account. (Ville)
v4:
- Train request printing for TX FFE (Ville)
- Log 8b/10b vs. 128b/132b (Ville)
- Add helper for per-lane max vswing / tx ffe (Ville)
- Name functions with tx_ffe/vswing instead of 128b132b/8b10b
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211011182144.22074-2-jani.nikula@intel.com
The "digi_port" pointer can't be NULL and we have already dereferenced
it so checking for NULL is not necessary. Delete the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211004103737.GC25015@kili
In order to have per-lane drive settings we need intel_ddi_level()
to accept the lane as a parameter. That is, the eventual goal is to
call intel_ddi_level() once for each lane. For now we just pass in
a hardcoded 0 and use the same settings for every lane. Ie. no
change in behaviour yet.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-9-ville.syrjala@linux.intel.com
Since intel_ddi_level() now looks at the buf_trans table there's
no point in having intel_ddi_hdmi_num_entries() around. Just
roll the necessary bits of locic into
intel_ddi_hdmi_level()/intel_ddi_level().
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-8-ville.syrjala@linux.intel.com
All callers of intel_ddi_level() duplicate the check+WARN
to make sure the returned level is actually present in the
appropriate buf_trans table. Let's push that stuff into
intel_ddi_level() so the callers don't have to worry about it.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-7-ville.syrjala@linux.intel.com
Currently .set_signal_levels() is only used by encoders in DP mode.
For most modern platforms there is no essential difference between
DP and HDMI, and both codepaths just end up calling the same function
under the hood. Let's get remove the need for that extra indirection
by moving .set_signal_levels() into the encoder from intel_dp.
Since we already plumb the crtc_state/etc. into .set_signal_levels()
the code will do the right thing for both DP and HDMI.
HSW/BDW/SKL are the only platforms that need a bit of care on
account of having to preload the hardware buf_trans register
with the full set of values. So we must still remember to call
hsw_prepare_{dp,hdmi}_ddi_buffers() to do said preloading, and
.set_signal_levels() will just end up selecting the correct entry
for DP, and also setting up the iboost magic for both DP and HDMI.
Note that previously on HSW/BDW/SKL we did write to DDI_BUF_CTL to
select the correct entry until link training started, now that we
call .set_signal_levels() already from hsw_ddi_pre_enable_dp() that
is no longer the case. But it's all safe now that the
intel_ddi_init_dp_buf_reg() call was hoisted up and it no longer
sets up the DDI_BUF_CTL_ENABLE bit (that is still deferred until
link training).
v2: Rebase due to has_{iboost,buf_trans_select}()
Add some notes about the DDI_BUF_CTL situation on HSW/BDW/SKL (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-4-ville.syrjala@linux.intel.com
Add a small helper to determine if DDI_BUF_CTL uses the
DDI_BUF_TRANS_SELECT field, and whether we have the
accompanying DDI_BUF_TRANS table in the hardware.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
I want intel_dp->DP to be fully populated by the time the
initial vswing programming happens. To that end move the
intel_ddi_init_dp_buf_reg() call to an earlier spot.
Additionally we don't want intel_ddi_init_dp_buf_reg() to
set DDI_BUF_CTL_ENABLE since the port should only get enabled
at the start of link training (see intel_ddi_prepare_link_retrain()).
So any earlier write to the register should not set the enable bit.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
So far TC-cold was blocked only for the duration of TypeC mode resets.
The DP-alt and legacy modes require TC-cold to be blocked also whenever
the port is in use (AUX transfers, enable modeset), and this was ensured
by the held PHY ownership flag. On ADL-P this doesn't work, since the
PHY ownership flag is in a register backed by the PW#2 power well.
Whenever this power well is disabled the ownership flag is cleared by
the HW under the driver.
The only way to cleanly release and re-acquire the PHY ownership flag
and also allow for power saving (by disabling the display power wells
and reaching DC5/6 states) is to hold the TC-cold blocking power domains
while the PHY is connected and disconnect/reconnect the PHY on-demand
around AUX transfers and modeset enable/disables. Let's do that,
disconnecting a PHY with a 1 sec delay after it becomes idle. For
consistency do this on all platforms and TypeC modes.
v2: Add tc_mode!=disconnected and phy_is_owned asserts to
__intel_tc_port_lock().
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-6-imre.deak@intel.com
Instead of directly accessing the TypeC port internal struct members,
add/use helpers to retrieve the corresponding properties.
No functional change.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-6-imre.deak@intel.com
Atm during driver loading and system resume TypeC ports are accessed
before their HW/SW state is synced. Move the TypeC port sanitization to
the encoder's sync_state hook to fix this.
v2: Handle the encoder disabled case in gen11_dsi_sync_state() as well
(Jose, Jani)
Fixes: f9e76a6e68 ("drm/i915: Add an encoder hook to sanitize its state during init/resume")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-1-imre.deak@intel.com
PSR always had a requirement to only be enabled if there is active
planes but not following that never caused any issues.
But that changes in Alderlake-P, leaving PSR enabled without
active planes causes transcoder/port underruns.
Similar behavior was fixed during the pipe disable sequence by
commit 84030adb9e ("drm/i915/display: Disable audio, DRRS and PSR before planes").
intel_dp_compute_psr_vsc_sdp() had to move from
intel_psr_enable_locked() to intel_psr_compute_config() because we
need to be able to disable/enable PSR from atomic states without
connector and encoder state.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922215242.66683-3-jose.souza@intel.com
128b/132b has a separate transcoder DDI mode, which also requires the
MST transport select to be set. Note that we'll use DP MST also for
single-stream 128b/132b.
Having the FDI and 128b/132b modes share the register mode value
complicates things a bit.
v2:
- Use HAS_DP20 abstraction for 128b/132b mode (Ville)
- Use intel_dp_is_uhbr() helper
Bspec: 50493
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/279bfbd979e0256fae13a5231e07e2f4fb665c07.1631191763.git.jani.nikula@intel.com
PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder.
Bigjoiner is making life even more confusing by introducing
a N:1 relationship between pipes and transcoders. In that case
we only enable/configure the transcoder corresponding to the
master pipe. Let's do some renames to make it clear we're dealing
with the transcoder rather than pipe when it comes to
PIPECONF/TRANSCONF.
I decided to leave the _cpu_ part out from the function/macro
names since the PCH transcoder related stuff already has a
_pch_ in their name. So shouldn't be possible to confuse them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We had a mix of intel_edp_drrs_*(), intel_dp_drrs_*() and
intel_dp_set_drrs_state(), so properly renaming all functions to
keep the same pattern.
While at it, also dropping intel_dp_set_drrs_state from the
documentation as it is a static function.
v3:
- dropping documentation style comment in static function
(intel_drrs_set_state)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-3-jose.souza@intel.com
intel_dp.c is a 5k lines monster, so moving DRRS out of it to reduce
some lines from it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-2-jose.souza@intel.com
We use encoder->get_buf_trans() in many places, for example
intel_ddi_dp_voltage_max(), and the hook was set to some old platform's
function for DG2 SNPS PHY. Convert SNPS PHY to use the same translation
mechanisms as everything else.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210813115151.19290-2-jani.nikula@intel.com
ADL-P supports stream splitter on pipe B in addition to pipe A. Update
the sanity check in intel_ddi_mso_get_config() to reflect this, and
remove the check in intel_ddi_mso_configure() as redundant with
encoder->pipe_mask. Abstract the splitter pipe mask to a single point of
truth while at it to avoid similar mistakes in the future.
Fixes: 7bc188cc2c ("drm/i915/adl_p: enable MSO on pipe B")
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Tested-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812132354.10885-1-jani.nikula@intel.com
DG1 and XE_PLD platforms has Audio MMIO/VERBS lies in PG0 power
well. Adjusting the power domain accordingly to
POWER_DOMAIN_AUDIO_MMIO for audio detection and
POWER_DOMAIN_AUDIO_PLAYBACK for audio playback.
While doing this it requires to use POWER_DOMAIN_AUDIO_MMIO
power domain instead of POWER_DOMAIN_AUDIO in crtc power domain mask
and POWER_DOMAIN_AUDIO_PLAYBACK with intel_display_power_{get, put}
to enable/disable display audio codec power.
It will save the power in use cases when DP/HDMI connectors
configured with PIPE_A without any audio playback.
v1: Changes since RFC
- changed power domain names. [Imre]
- Removed TC{3,6}, AUX_USBC{3,6} and TBT from DG1
power well and PW_3 power domains. [Imre]
- Fixed the order of powe wells , power domains and its
registration. [Imre]
v2:
- Not allowe DC states when AUDIO_MMIO domain enabled. [Imre]
v3:
- Squashes the commits of series to avoid build failure.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
[Fix typo in commit message and in AUDIO_PLAYBACK domain name]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210729121858.16897-2-anshuman.gupta@intel.com
The only real platform with DISPLAY_VER == 10 is GLK. We don't need to
handle CNL explicitly in intel_ddi.c.
Remove code and rename functions/macros accordingly to use ICL prefix.
There's one leftover reference to cnl that comes from the struct
intel_ddi_buf_trans. This will be renamed later when we get rid of the
additional CNL tables.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728215946.1573015-7-lucas.demarchi@intel.com
DG2 has some changes to the expected modesetting sequences when compared
to gen12. Adjust our driver logic accordingly. Although the DP
sequence is pretty similar to TGL's, there are some steps that change,
so let's split the handling for that out into a separate function.
v2:
- Switch wait_for_us() -> _wait_for() so that we can parameterize the
timeout rather than duplicating the macro call. (Jani)
Bspec: 54128
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-27-matthew.d.roper@intel.com
Vswing programming for SNPS PHYs is just a single step -- look up the
value that corresponds to the voltage level from a table and program it
into the SNPS_PHY_TX_EQ register.
Bspec: 53920
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-26-matthew.d.roper@intel.com
At the moment we don't have a proper algorithm that can be used to
calculate PHY settings for arbitrary HDMI link rates. The PHY tables
here should support the regular modes of real-world HDMI monitors.
Bspec: 54032
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-25-matthew.d.roper@intel.com
HDMI and DisplayPort sequences states that audio and PSR should be
disabled before planes are disabled.
Not following it did not caused any problems up to Alderlake-P but
for this platform it causes underruns during the PSR2 disable
sequence.
Specification don't mention that DRRS should be disabled before planes
but it looks safer to switch back to the default refresh rate before
following with the rest of the pipe disable sequence.
BSpec: 49191
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210726181559.80855-1-jose.souza@intel.com
_DG1_DPCLKA0_CFGCR0 maps between DPLL 0 and 1 with one bit for phy A
and B while _DG1_DPCLKA1_CFGCR0 maps between DPLL 2 and 3 with one
bit for phy C and D.
Reusing _cnl_ddi_get_pll() don't take that into cosideration returing
DPLL 0 and 1 for phy C and D.
That is a regression introduced in the refactor done in
commit 351221ffc5 ("drm/i915: Move DDI clock readout to
encoder->get_config()").
While at it also dropping the macros previously used, not reusing it
to improve readability.
BSpec: 50286
Fixes: 351221ffc5 ("drm/i915: Move DDI clock readout to encoder->get_config()")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210630210522.162674-1-jose.souza@intel.com
Disconnect TypeC PHYs during system suspend and shutdown, even with the
corresponding TypeC sink still plugged to its connector, since leaving
the PHY connected causes havoc at least during system resume in the
presence of an Nvidia card.
Note that this will only make a difference in the TypeC DP alternate
mode, since in Thunderbolt alternate mode the PHY is never owned by the
display engine and there is no notion of PHY ownership in legacy mode
(the display engine being the only possible owner in that mode and the
TypeC subsystem not having anything to do with the port in that case).
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3500
Reported-and-tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610174223.605904-1-imre.deak@intel.com
Looks this FIXME is still valid as we need a way to tell LSPCON to
stop sending infoframes, so reverting it.
This reverts commit 3f409e4cd5.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610194527.84997-1-jose.souza@intel.com
intel_dp_set_infoframes() call in intel_ddi_post_disable_dp() will
take care to disable all enabled infoframes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514232247.144542-4-jose.souza@intel.com
An async-put on an encoder specific power domain (for instance the AUX
PW domain) may be pending when removing the encoder. Make sure any such
async-puts are complete while the corresponding encoder is still in place
since at least AUX power wells require this to do a power well->PHY
lookup.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210526143729.2563672-1-imre.deak@intel.com
On ADL-P, it's possible to enable the stream splitter on pipe B in
addition to pipe A.
Bspec: 50174
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210526082903.26395-1-jani.nikula@intel.com
On ADL_P besides programming the PLL accordingly the DP/HDMI link rate
should be also programmed to the DDI_BUF_CTL register, do that.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-16-lucas.demarchi@intel.com
Define and use DP voltage swing and pre-emphasis translation tables
for ADL-P.
v2:
- Update according to recent bspec updates; there are now separate
tables for RBR/HBR and HBR2/HBR3. (Anusha)
BSpec: 54956
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-14-lucas.demarchi@intel.com
ADL-P have basically the same TC connection and disconnection
sequences as ICL and TGL, the major difference is the new registers.
So here adding functions without the icl prefix in the name and
making the new functions call the platform specific function to access
the correct register.
v2:
- Retain DDI TC PHY ownership flag during modesetting.
BSpec: 55480
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-6-lucas.demarchi@intel.com
Disable loadgen sharing for DP link rate 1.62 GHz and HDMI 5.94 GHz.
For all other modes, we can enable loadgen sharing feature.
BSpec: 55359
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-13-matthew.d.roper@intel.com
The DDI naming template for display version 12 went A-C, TC1-TC6. With
XE_LPD, that naming scheme for DDI's has now changed to A-E, TC1-TC4.
The XE_LPD design keeps the register offsets and bitfields relating to
the TC outputs in the same location they were previously. The new "D"
and "E" outputs now take the locations that were previously used by TC5
and TC6 outputs, or what we would have considered to be outputs "H" and
"I" under the legacy lettering scheme.
For the most part everything will just work as long as we initialize the
output with the proper 'enum port' value. However we do need to take
care to pick the correct AUX channel when parsing the VBT (e.g., a
reference to 'AUX D' is actually asking us to use the 8th aux channel,
not the fourth). We should also make sure that our encoders and aux
channels are named appropriately so that it's easier to correlate driver
debug messages with the bspec instructions.
v2:
- Update handling of TGL_TRANS_CLK_SEL_PORT. (Jose)
v3:
- Add hpd_pin to handle outputs D and E (Jose)
- Fixed conversion of BIOS port to aux ch for TC ports (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-2-matthew.d.roper@intel.com
So far if we had a mismatch between the state asked and what was
programmed in hardware for PSR, this mismatch would go unnoticed.
So here adding the PSR to the hardware configuration readout,
EDP_PSR_CTL and EDP_PSR2_CTL can't be directly read because its state
flips due to other factors like frontbuffer modifications and CRC.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210418002126.87882-1-jose.souza@intel.com
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:
1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?
2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check
With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.
So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:
@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1
@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1
@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com
Just let bxt/glk fall back to intel_hpd_pin_default() instead
of using skl_hpd_pin() or cnl_hpd_pin(). Doesn't really matter
since both functions will end up returning the correct hpd pin
anyway, but I find it a bit less confusing when bxt/glk are
fully separated from the logic for the other platforms.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210412054607.18133-5-ville.syrjala@linux.intel.com
Now that we've eliminated INTEL_GEN(), IS_GEN_RANGE(), etc. from the
display code, we should also kill off our use of the IS_GEN9_* macros
too. We'll do the conversion manually this time instead of using
Coccinelle since the most logical substitution can depend heavily on the
code context, and sometimes we can keep the code simpler if we make
additional adjustments such as swapping the order of if/else arms.
v2:
- Restore a lost negation in intel_pll_is_valid().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210407203945.1432531-1-matthew.d.roper@intel.com
(cherry picked from commit 70bfb30743)
[Jani: cherry picked to topic branch to reduce conflicts]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
Add intel_bios_encoder_data pointer to encoder, and use it for hdmi and
dp iboost. For starters, we only set the encoder->devdata for DDI
encoders, i.e. we can only use it for data that is used by DDI encoders.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4bc49244ce68e136e5b21db4c4e6554bec9ac0fb.1615998927.git.jani.nikula@intel.com
Stop caching the information in ddi_port_info. We're phasing out
ddi_port_info usage completely, and prefer using the VBT child device
information directly using the provided helpers.
v2:
- Remove supports_typec_usb & supports_tbt from ddi_vbt_port_info (Lucas)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b04bd183e7554aeb4bc3962af90d63171aa32fc2.1615998927.git.jani.nikula@intel.com
Start using struct intel_bios_encoder_data directly. We'll start
sanitizing the child device data directly as well, instead of the cached
data in ddi_port_info[]. The one downside here is having to store a
non-const pointer back to intel_bios_encoder_data.
Eventually we'll be able to have a direct pointer from encoder to
intel_bios_encoder_data, removing the need to go through the
ddi_port_info[] array altogether. And we'll be able to remove all the
cached data in ddi_port_info[].
v2:
- Remove supports_dp and supports_edp from ddi_port_info too
- Add devdata != NULL check in intel_bios_is_port_edp()
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> # v1
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/061df32a012ff640060920fcd730fb23f8717ee8.1615998927.git.jani.nikula@intel.com
Let's check that we actually found the PLL before doing the
port_clock readout, just in case the hardware was severly
misprogrammed by the previous guy. Not sure the hw would
even survive such misprogramming without hanging but no
real harm in checking anyway.
Cc: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210310194351.6233-1-ville.syrjala@linux.intel.com
Reviewed-by: Karthik B S <karthik.b.s@intel.com>
Now that all the encoder clock stuff is uniformly abstracted
for all hsw+ platforms, let's extend icl_sanitize_encoder_pll_mapping()
to cover all of them.
Not sure there is a particular benefit in doing so, but less special
cases always makes me happy.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-7-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Support reading out the current state of the DDI clock.
Not sure we really want this. Seems a bit excessive just to
restore the debug print to icl_sanitize_encoder_pll_mapping()?
But maybe there's more use for it?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-6-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Move the *_get_ddi_pll() stuff into the encodet->get_config() hook.
There it neatly sits next to the matching .{enable,disable}_clock()
functions.
In order to avoid excessive boilerplate I changed the behaviour
such that all platforms now do the readout via
crtc_state->port_dpll[].
ICL+ TC is still a bit special due to TBTPLL not having a functional
.get_freq(). Should probably change that by adopting the LCPLL
approach, but that would require a fairly substantial rework of the
DPLL ID handling. So leave it for later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-5-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
On platforms/outputs without a working frame counter we rely
on the vblank code to cook up the frame counter from the timestamps.
That requires that vblank support is enabled. Thus we need to
move the pipe enable/disable tracepoints to the other side
of the drm_vblank_{on,off}() calls. There shouldn't really be
much happening between these old and new call sites so the
tracepoints should still provide reasonable data.
The alternative would be to give up on having the frame counter
values in the trace which would render the tracepoints more or
less pointless.
v2: Missed one case in intel_ddi_post_disable()
Drop the now useless i915_trace.h includes
Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210304170421.10901-2-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Add splitter configuration to crtc state, and read it where
supported. Also add splitter state dumping. The stream splitter will be
required for eDP MSO.
v4:
- Catch invalid splitter configuration (Uma)
v3:
- Convert segment timings to full panel timings.
- Refer to splitter instead of mso in crtc state.
- Dump splitter state.
v2: Add warning for mso being enabled on pipes other than A.
Cc: Nischal Varide <nischal.varide@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/95cbe1c9d45edf3e3ec252e49fb49055def98155.1614682842.git.jani.nikula@intel.com
Instead of every new platform having yet another masive
copy of the whole PLL sanitation code, let's just reuse the
.disable_clock() hook for this purpose. We do need to plug
this into the ICL+ DSI code for that, but fortunately it
already has a suitable function we can use.
We do lose the debug message though on account of not bothering
to check if the clock is actually enabled or not before turning
it off. We could introduce yet another vfunc to query the current
state, but not sure it's worth the hassle?
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-14-ville.syrjala@linux.intel.com
Since .{enable,disable}_clock() are already vfuncs it's a bit silly to
have if-ladders inside them. Just provide specialized version for adl-s
and rkl so we don't need any of that.
v2: s/dev_priv/i915/ (Lucas)
Fix typos in platform names (Lucas)
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-13-ville.syrjala@linux.intel.com
The other DDI .enable_clock() functions are trying to protect us
against pll==NULL. A bit tempted to throw out all the WARNs as
just unnecessary noise, but I guess they might have some use
when poking around the shared_dpll code (not sure it wouldn't
oops elsewhere though). So let's unify it all and sprinkle in
the missing WARNs for icl/dg1.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-11-ville.syrjala@linux.intel.com
The current code attempts to protect the RMWs into global
clock routing registers with a mutex, but forgets to do so
in a few places. Let's remedy that.
Note that at the moment we serialize all modesets onto single
wq, so this shouldn't actually matter. But maybe one day we
wish to attempt parallel modesets again...
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-10-ville.syrjala@linux.intel.com
For ICL+ we have several styles of clock routing for DDIs:
1) TC DDI + TC PHY
-> needs DDI_CLK_SEL==MG/TBT part form intel_ddi_clk_{select,disable}()
and ICL_DPCLKA_CFGCR0_TC_CLK_OFF part form icl_{map,unmap}_plls_to_ports()
2) ICL/TGL combo DDI + combo PHY
-> just need the stuff from icl_{map,unmap}_plls_to_ports()
3) JSL/EHL TC DDI + combo PHY
-> needs DDI_CLK_SEL==MG part from intel_ddi_clk_{select,disable}() and
the full combo style clock selection from icl_{map,unmap}_plls_to_ports()
4) ADLS/RKL
-> these use both TC and combo DDIs with combo PHYs, however they
always use the full combo style clock selection as per
icl_{map,unmap}_plls_to_ports() and do not use DDI_CLK_SEL at all,
thus get treated the same as 2)
We extract all that from the current mess in the following way:
1) icl_ddi_tc_{enable,disable}_clock()
2) icl_ddi_combo_{enable,disable}_clock()
3) jsl_ddi_tc_{enable,disable}_clock()
4) for now we reuse icl_ddi_combo_{enable,disable}_clock() here
v2: s/dev_priv/i915/ (Lucas)
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-8-ville.syrjala@linux.intel.com
Yank out the HSW/BDW code from intel_ddi_clk_{select,disable}()
and put it into the new encoder .{enable,disable}_clock() vfuncs.
v2: s/dev_priv/i915/ (Lucas)
v3: Deal with FDI
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-4-ville.syrjala@linux.intel.com
The current code dealing with the clock routing for DDI encoders
is a maintenance nightmare. Let's start cleaning it up by allowing
the encoder to provide vfuncs for enablign/disabling the clock.
We leave them initially unimplemented, falling back to the old
if-else approach.
v2: Convert the FDI enable sequence
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-3-ville.syrjala@linux.intel.com
