Accessing the TypeC DKL PHY registers during modeset-commit,
-verification, DP link-retraining and AUX power well toggling is racy
due to these code paths being concurrent and the PHY register bank
selection register (HIP_INDEX_REG) being shared between PHY instances
(aka TC ports) and the bank selection being not atomic wrt. the actual
PHY register access.
Add the required locking around each PHY register bank selection->
register access sequence.
Kudos to Ville for noticing the race conditions.
v2:
- Add the DKL PHY register accessors to intel_dkl_phy.[ch]. (Jani)
- Make the DKL_REG_TC_PORT macro independent of PHY internals.
- Move initing the DKL PHY lock to a more logical place.
v3:
- Fix parameter reuse in the DKL_REG_TC_PORT definition.
- Document the usage of phy_lock.
v4:
- Fix adding TC_PORT_1 offset in the DKL_REG_TC_PORT definition.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025114457.2191004-1-imre.deak@intel.com
(cherry picked from commit 89cb0ba4ceee6bed1059904859c5723b3f39da68)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We always allocate two DPLLs (TC and TBT) for TC ports. This
is because we can't know ahead of time wherher we need to put
the PHY into DP-Alt or TBT mode.
However during readout we can obviously only read out the state
of the DPLL that the port is actually using. Thus the state after
readout will not have both DPLLs populated.
We run into problems if during readout the TC port is in DP-Alt
mode, but we then perform a modeset on the port without going
through the full .compute_config() machinery, and during said
modeset the port cannot be switched back into DP-Alt mode and
we need to take the TBT fallback path. Such a modeset can
happen eg. due to cdclk reprogramming.
This wasn't a problem earlier because we did all the DPLL
calculations much later in the modeset. So even if flagged
a modeset very late we'd still have gone through the DPLL
calculations. But now all the DPLL calculations happen much
earlier and so we need to deal with it, or else we'll attempt
a modeset without a DPLL.
To guarantee that we always have both DPLLs fully cal/ulated
for TC ports force a full modeset computation during the
initial commit.
v2: Avoid bitwise operation on bool (Jani)
Call the return variable 'fastset' to convey its meaning
Reported-by: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: b000abd3b3 ("drm/i915: Do .crtc_compute_clock() earlier")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922191236.4194-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit eddb4afcb6c533d3f75f5f1a77e292fece27570e)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Make sure the TypeC PHY ownership flag is not getting reset during
an HDMI modeset on the given port. Besides the WARN this triggered, it
didn't cause other issues, since for TypeC legacy mode setting the
PHY ownership flag is optional (there is no other user of the PHY
besides display).
Reported-and-tested-by: Shawn C Lee <shawn.c.lee@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220726134313.1484763-1-imre.deak@intel.com
Starting with TGL the disabling order of HDMI transcoder clock vs. DDI
BUF has swapped, fix this. There hasn't been any issues seen related to
this, but let's follow the spec.
Reported-by: Sandeep K Lakkakula <sandeep.k.lakkakula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617112807.1586621-1-imre.deak@intel.com
Extract intel_crtc_dotclock() from ddi_dotclock_get(). We'll reuse
this during state computation in order to determine the actual final
dotclcok after the DPLL computation has been done (which may not give
us the exact same port_clock that we fed in).
v2: Add the prototype
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220504123350.13235-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Split out audio registers to a header of its own to reduce the size of
i915_reg.h.
TODO: Remove direct audio register access from intel_ddi.c. However,
unification of audio get config is cumbersome due to the audio enable
bit being in the DP or HDMI registers on older platforms.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220602094542.1386151-1-jani.nikula@intel.com
Avoid bringing the entire machine down even if there's a bug that
shouldn't happen, but won't corrupt the system either. Log them loudly
and limp on.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531162527.1062319-1-jani.nikula@intel.com
We have the same "override eDP VBT bpp with the current bpp" code
duplciated in two places. Extract it to a helper function.
TODO: Having this in .get_config() is pretty ugly. Should probably
try to move it somewhere else (setup_hw_state()/etc.)...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
drm/i915 feature pull #2 for v5.19:
Features and functionality:
- Add first set of DG2 PCI IDs for "motherboard down" designs (Matt Roper)
- Add initial RPL-P PCI IDs as ADL-P subplatform (Matt Atwood)
Refactoring and cleanups:
- Power well refactoring and cleanup (Imre)
- GVT-g refactor and mdev API cleanup (Christoph, Jason, Zhi)
- DPLL refactoring and cleanup (Ville)
- VBT panel specific data parsing cleanup (Ville)
- Use drm_mode_init() for on-stack modes (Ville)
Fixes:
- Fix PSR state pipe A/B confusion by clearing more state on disable (José)
- Fix FIFO underruns caused by not taking DRAM channel into account (Vinod)
- Fix FBC flicker on display 11+ by enabling a workaround (José)
- Fix VBT seamless DRRS min refresh rate check (Ville)
- Fix panel type assumption on bogus VBT data (Ville)
- Fix panel data parsing for VBT that misses panel data pointers block (Ville)
- Fix spurious AUX timeout/hotplug handling on LTTPR links (Imre)
Merges:
- Backmerge drm-next (Jani)
- GVT changes (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87bkwbkkdo.fsf@intel.com
SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.
To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-9-tzimmermann@suse.de
Atm the port -> DDI and AUX power domain mapping is specified by relying
on the aliasing of the platform specific intel_display_power_domain enum
values. For instance D12+ platforms refer to the 'D' port and power
domain instances, which doesn't match the bspec terminology, on these
platforms the corresponding port is TC1. To make it clear what
port/domain the code refers to add a mapping between them which matches
the bspec terms on different display versions.
This also allows for removing the aliasing in enum values in a follow-up
patch.
v2: Add the functions to intel_display_power.c, use
intel_display_power_ prefix.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-14-imre.deak@intel.com
When the PHY fails on calibration we were previously skipping the ddi
initialization. However the driver is not really prepared for that,
ultimately leading to a NULL pointer dereference:
[ 75.748348] i915 0000:03:00.0: [drm:intel_modeset_init_nogem [i915]] SNPS PHY A failed to calibrate; output will not be used.
...
[ 75.750336] i915 0000:03:00.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:80:pipe A] hw state readout: enabled
...
( no DDI A/PHY A )
[ 75.753080] i915 0000:03:00.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:235:DDI B/PHY B] hw state readout: disabled, pipe A
[ 75.753164] i915 0000:03:00.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:245:DDI C/PHY C] hw state readout: disabled, pipe A
...
[ 75.754425] i915 0000:03:00.0: [drm] *ERROR* crtc 80: Can't calculate constants, dotclock = 0!
[ 75.765558] i915 0000:03:00.0: drm_WARN_ON_ONCE(drm_drv_uses_atomic_modeset(dev))
[ 75.765569] WARNING: CPU: 5 PID: 1759 at drivers/gpu/drm/drm_vblank.c:728 drm_crtc_vblank_helper_get_vblank_timestamp_internal+0x347/0x360
...
[ 75.781230] BUG: kernel NULL pointer dereference, address: 000000000000007c
[ 75.788198] #PF: supervisor read access in kernel mode
[ 75.793347] #PF: error_code(0x0000) - not-present page
[ 75.798480] PGD 0 P4D 0
[ 75.801019] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 75.805377] CPU: 5 PID: 1759 Comm: modprobe Tainted: G W 5.18.0-rc1-demarchi+ #199
[ 75.827613] RIP: 0010:icl_aux_power_well_disable+0x3b/0x200 [i915]
[ 75.833890] Code: 83 ec 30 65 48 8b 04 25 28 00 00 00 48 89 44 24 28 48 8b 06 0f b6 70 1c f6 40 20 04 8d 56 fa 0f 45 f2 e8 88 bd ff ff 48 89 ef <8b> 70 7c e8 ed 67 ff ff 48 89 ef 89 c6 e8 73 67 ff ff 84 c0 75 0a
[ 75.852629] RSP: 0018:ffffc90003a7fb30 EFLAGS: 00010246
[ 75.857852] RAX: 0000000000000000 RBX: ffff8881145e8f10 RCX: 0000000000000000
[ 75.864978] RDX: ffff888115220840 RSI: 0000000000000000 RDI: ffff888115220000
[ 75.872106] RBP: ffff888115220000 R08: ffff88888effffe8 R09: 00000000fffdffff
[ 75.879234] R10: ffff88888e200000 R11: ffff88888ed00000 R12: ffff8881145e8f10
[ 75.886363] R13: 0000000000000001 R14: ffff888115223240 R15: 0000000000000000
[ 75.893490] FS: 00007ff6e753a740(0000) GS:ffff88888f680000(0000) knlGS:0000000000000000
[ 75.901573] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 75.907313] CR2: 000000000000007c CR3: 00000001216a6001 CR4: 0000000000770ee0
[ 75.914446] PKRU: 55555554
[ 75.917153] Call Trace:
[ 75.919603] <TASK>
[ 75.921709] intel_power_domains_sanitize_state+0x88/0xb0 [i915]
[ 75.927814] intel_modeset_init_nogem+0x317/0xef0 [i915]
[ 75.933205] i915_driver_probe+0x5f6/0xdf0 [i915]
[ 75.937976] i915_pci_probe+0x51/0x1d0 [i915]
We skip the initialization of PHY A, but later we try to find out what
is the phy for that power well and dereference dig_port, which is NULL.
Failing the PHY calibration could be left as a warning or error, like it
was before commit b4eb76d82a ("drm/i915/dg2: Skip output init on PHY
calibration failure"). However that often fails for outputs not being
used, which would make the warning/error appear on systems that have no
visible issues. Anyway, there is still a need to fix those failures,
but that is left for later.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220410061537.4187383-1-lucas.demarchi@intel.com
Let's just do a full DRRS disable/enable across all pipe updates.
This guarantees that the DRRS work doesn't interfere with anything
while the atomic commit is busy reprogramming the pipe.
Needed so that we can start reprogramming M/N seamlessly during
fastsets whenever possible. Also avoids the pre-bdw DRRS PIPECONF
rmw racing with the potential PIPECONF write from the atomic
commit (eg. due to GAMMA_MODE changes).
v2: Include has_drrs in state dump (José)
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315213944.17132-1-ville.syrjala@linux.intel.com
No reason to keep the DRRS enable/disable hidden insider the encoder
hooks. Let's just move them all the way up into platform independent
code so that all platforms get to use them. These are nops when
the state computation doesn't think DRRS is possible.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-14-ville.syrjala@linux.intel.com
Ger rid of one more ugly crtc->config usage by storing the DRRS
state under intel_crtc. intel_drrs_enable() copies what it needs
from the crtc state, after which DRRS can be blissfully ignorant
of anything going on around it.
This also lets multiple pipes do DRRS simultanously and entirely
independently.
v2: Split out some stuff (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Remove the local enabledisable() implementation and adopt the
str_enable_disable() from linux/string_helpers.h.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220225234631.3725943-2-lucas.demarchi@intel.com
If one of our PHYs fails to complete calibration, we should skip the
general initialization of the corresponding output. Most likely this is
going to happen on outputs that don't actually exist on the board; in
theory we should have already decided to skip this output based on the
VBT, but we can't always rely on the VBT being accurate.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223165421.3949883-1-matthew.d.roper@intel.com
Add display workaround # 1309179469 , which fixes a PHY hang when
switching from TBT mode to DP-alt/legacy mode. The workaround also
requires an IFWI/PHY firmware change, before that this change has no
effect (the DKL_PCS_DW5/SOFTRESET flag is always cleared).
HSDES: 18018237866
HSDES: 16014473319
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218122611.767974-1-imre.deak@intel.com
Get rid of the inflexible bigjoiner_linked_crtc pointer thing
and just track things as a bitmask of pipes instead. We can
also nuke the bigjoiner_slave boolean as the role of the pipe
can be determined from its position in the bitmask.
It might be possible to nuke the bigjoiner boolean as well
if we make encoder.compute_config() do the bitmask assignment
directly for the master pipe. But for now I left that alone so
that encoer.compute_config() will just flag the state as needing
bigjoiner, and the intel_atomic_check_bigjoiner() is still
responsible for determining the bitmask. But that may have to change
as the encoder may be in the best position to determine how
exactly we should populate the bitmask.
Most places that just looked at the single bigjoiner_linked_crtc
now iterate over the whole bitmask, eliminating the singular
slave pipe assumption.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203183823.22890-11-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Instead of passing in the whole crtc state let's pass in just
the bits of state we need. This will help with the DRRS code
which shouldn't really be accessing the atomic state stuff directly
as it gets called outside the normal atomic flows.
v2: Fix set_m1_n1 vs. set_m2_n2 fumble for i9xx (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Make things a bit more explicit by splitting
intel_cpu_transcoder_set_m_n() into separate variants for M1/N1 vs.
M2/N2. Makes the DRRS M/N programming at least more obvious.
Note that for the MST and DRRS cases we don't need to call the
M2/N2 variant at all since the transcoders that support those
do not have the M2/N2 registers.
Same could be said for i9xx_crtc_enable() but I want to do a
higher level code sharing between that valleyview_crtc_enable()
later in which case we do need the M2/N2 variant. This is also
why I keep the transcoder_has_m2_n2() in intel_cpu_transcoder_set_m2_n2()
so the caller doesn't have necessarily care what the chosen
transcoder supports.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
I want to make a clean split betwen the CPU vs. PCH transcoder
programming. To that end eliminate intel_dp_set_m_n() and just
call the individual CPU/PCH transcoder functions directly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Lift the dsc/joiner enable up from the wonky places where it
currently sits (ddi .pre_enable() or icl_ddi_bigjoiner_pre_enable())
into hsw_crtc_enable() where we write the other per-pipe stuff
as well. Makes the transcoder vs. pipe split less confusing.
For DSI this results in slight reordering between the dsc/joiner
enable vs. transcoder timings setup, but I can't really think
why that should cause any issues since the transcoder isn't yet
enabled at that point.
v2: Take care of dsi (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220125063937.7003-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
dg2_ddi_pre_enable_dp() has outlived its usefulness so eliminate
it.
The one thing that tgl_ddi_pre_enable_dp() is missing that we
need is intel_ddi_config_transcoder_dp2(). So we'll bring that
over.
tgl_ddi_pre_enable_dp() does also have a few things that
dg2_ddi_pre_enable_dp() didn't have:
- icl_program_mg_dp_mode() -> nop due to intel_phy_is_tc()==false on DG2
- intel_ddi_power_up_lanes() -> nop due to intel_phy_is_combo()==false on DG2
- intel_ddi_mso_configure() -> only matters for MSO panels
Another slight difference is that dg2_ddi_pre_enable_dp() was
missing a bigjoiner check around intel_dsc_enable(), which
tgl_ddi_pre_enable_dp() does have.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119122150.12941-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
TC voltage swing programming sequence was updated with a new step.
BSpec: 54956
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220113174826.50272-1-jose.souza@intel.com
Registers representing the MG/DKL TC PHYs (including the TC DPLLs which
exist inside the PHY) are only needed in a couple files and on specific
platforms; let's keep them separate from the general register pool.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220111051600.3429104-11-matthew.d.roper@intel.com
Add support for eDP panels with a built-in privacy screen using the
new drm_privacy_screen class.
Changes in v3:
- Move drm_privacy_screen_get() call to intel_ddi_init_dp_connector()
Changes in v2:
- Call drm_connector_update_privacy_screen() from
intel_enable_ddi_dp() / intel_ddi_update_pipe_dp() instead of adding a
for_each_new_connector_in_state() loop to intel_atomic_commit_tail()
- Move the probe-deferral check to the intel_modeset_probe_defer() helper
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005202322.700909-11-hdegoede@redhat.com
Currently we're only calling intel_update_active_dpll() for the
bigjoiner master pipe but not for the slave. With TC ports this
leads to the two pipes end up trying to use different PLLs
(TC vs. TBT). What's worse we're enabling the PLL that didn't get
intel_update_active_dpll() called on it at the spot where we
need the clocks turned on. So we turn on the wrong PLL and the
DDI is now trying to source its clock from the other PLL which is
still disabled. Naturally that doesn't end so well and the DDI
fails to start up.
The state checker also gets a bit unhappy (which is a good thing)
when it notices that one of the pipes was using the wrong PLL.
Let's fix this by remembering to call intel_update_active_dpll()
for both pipes. That should get the correct PLL turned on when
we need it, and the state checker should also be happy.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4434
Fixes: e12d6218fd ("drm/i915: Reduce bigjoiner special casing")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211105212156.5697-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Prepare for per-lane drive settings by querying the desired vswing
level per-lane.
Note that the code only does two loops, with each one writing the
levels for two TX lanes. The register offsets also look a bit funny
because each time through the loop we write to the exact same
register offsets. The crucial bit is the HIP_INDEX_REG
write that steers the same mmio window into different places.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006204937.30774-11-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Prepare for per-lane drive settings by querying the desired vswing
level per-lane.
Note that the code only does two loops, with each one writing the
levels for two TX lanes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006204937.30774-10-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
