It does not make sense to have a comma after a sentinel, as any new
elements must be added before the sentinel.
Add comments to clarify the purpose of the empty elements.
Rewrap entries to a single line to have a consistent style.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> [ahci_brcm]
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
DIPM is unsupported or broken on sunxi. Trying to enable the power
management policy med_power_with_dipm on an Allwinner A20 SoC based board
leads to immediate I/O errors and the attached SATA disk disappears from
the /dev filesystem. A reset (power cycle) is required to make the SATA
controller or disk work again. The A10 and A20 SoC data sheets and manuals
don't mention DIPM at all [1], so it's fair to assume that it's simply not
supported. But even if it was, it should be considered broken and best be
disabled in the ahci_sunxi driver.
[1] https://github.com/allwinner-zh/documents/tree/master/
Fixes: c5754b5220 ("ARM: sunxi: Add support for Allwinner SUNXi SoCs sata to ahci_platform")
Cc: stable@vger.kernel.org
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Link: https://lore.kernel.org/r/20210614072539.3307-1-public_timo.s@silentcreek.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Increasing the SATA/AHCI DMA TX/RX FIFOs (P0DMACR.TXTS and .RXTS, ie.
TX_TRANSACTION_SIZE and RX_TRANSACTION_SIZE) from default 0x0 each
to 0x3 each, gives a write performance boost of 120 MiB/s to 132 MiB/s
from lame 36 MiB/s to 45 MiB/s previously.
Read performance is above 200 MiB/s.
[tested on SSD using dd bs=4K/8K/12K/16K/20K/24K/32K: peak-perf at 12K]
Tested on the SBCs Banana Pi R1 (aka Lamobo R1) and Banana Pi M1 which
are based on the Allwinner A20 32bit-SoC (ARMv7-a / arm-linux-gnueabihf).
These devices are RaspberryPi-like small devices.
This problem of slow SATA write-speed with these small devices lasts
for about 7 years now (beginning with the A10 SoC). Many commentators
throughout the years wrongly assumed the slow write speed was a
hardware limitation. This patch finally solves the problem, which
in fact was just a hard-to-find software problem due to lack of
SATA/AHCI documentation by the SoC-maker Allwinner Technology.
Lists of the affected sunxi and other boards and SoCs with SATA using
the ahci_sunxi driver:
$ grep -i -e "^&ahci" arch/arm/boot/dts/sun*dts
and http://linux-sunxi.org/SATA#Devices_with_SATA_ports
See also http://linux-sunxi.org/Category:Devices_with_SATA_port
Tested-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Uenal Mutlu <um@mutluit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add the r40 compatible to the ahci_sunxi's supported list of
compatible.
Since R40 need ahci_platform to handle the reset controller, we also add
the new AHCI_PLATFORM_GET_RESETS flag for ahci_platform_get_resources().
This has no consequence for older platform (a10, a20) since the reset is
optional.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add an extra argument to ahci_platform_get_resources(), that is
for the bitmap representing the resource to get in this function.
Currently there is no resources to be defined, so all the callers set
'0' to the argument.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The owner module reference of the ahci platform's scsi_host is
initialized to libahci_platform's one, because these drivers use a
scsi_host_template defined in libahci_platform. So these drivers can
be unloaded even if the scsi device is being accessed.
This fixes it by pushing the scsi_host_template from libahci_platform
to all leaf drivers. The scsi_host_template is passed through a new
argument of ahci_platform_init_host().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The use of the AHCI_HFLAG_NO_PMP flag is something which we inherited from
the Allwinner android kernel sources, and I've always wanted to test if this
is really necessary.
So recently I've bought a sata port multiplexer, and I've given this a test
spin on both A10 and A20 devices, and it seems to work fine:
[ 2.154456] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.161092] ata1.15: Port Multiplier 1.2, 0x197b:0x0325 r0, 5 ports, feat 0x5/0xf
[ 2.175511] ata1.00: hard resetting link
[ 2.524929] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 2.531430] ata1.01: hard resetting link
[ 2.974465] ata1.01: link resume succeeded after 1 retries
[ 3.094932] ata1.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.101431] ata1.02: hard resetting link
[ 4.174466] ata1.02: failed to resume link (SControl 0)
[ 4.180065] ata1.02: SATA link down (SStatus 0 SControl 0)
(and the same for links 3 and 4)
Once the NO_PMP flag is removed it correctly sees the 2 disks which I've
attached, and I can mount and use them just fine.
Unfortunately when I then directly attached a disk to the sata port on the
sunxi SoC, and booted a kernel without the AHCI_HFLAG_NO_PMP flag, it would
not recognize that disk.
It turns out that the sata controller in the sunxi SoCs fails to handle
soft-resets issued to directly attached disks, and when pmp support is
enabled the kernel will always issue a soft-reset.
So add a module parameter to enable pmp usage, and default this to off, so
that directly attached disks keep working normally.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch moves force_port_map and mask_port_map into the
ahci_host_priv structure. This allows to modify them into the AHCI
framework. This is needed by the new dt bindings representing ports as
the port_map mask is computed automatically.
Parameters modifying force_port_map, mask_port_map and flags have been
removed from the ahci_platform_init_host() function, and inputs in the
ahci_host_priv structure are now directly filed.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a dynamic host_flags argument to make ahci_platform_init_host more flexible,
then remove the AHCI_HFLAGS(...) argument from some driver's ata_port_info,
and pass that in as the new argument.
Cc: Hans de Geode <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_sunxi_phy_init is called from the probe and resume code paths, and
sleeping is safe in both, so use msleep instead of mdelay.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds support for the ahci sata controler found on Allwinner A10
and A20 SoCs to the ahci_platform driver.
Orignally written by Olliver Schinagl using the approach of having a platform
device which probe method creates a new child platform device which gets
driven by ahci_platform.c, as done by ahci_imx.c .
Refactored by Hans de Goede to add most of the non sunxi specific functionality
to ahci_platform.c and use a platform_data pointer from of_device_id for the
sunxi specific bits.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
