Although we tried to fix the regression for the recent changes with
the delayed card registration, it doesn't seem covering the all
cases; e.g. on Roland EDIROL M-100FX, where the generic quirk for
Roland devices is applied, it misses the card registration because the
detection of the last interface (apparently for MIDI) fails.
This patch is an attempt to recover from those failures by calling the
card register also at the error path for the secondary interfaces.
The card register condition is also extended to match with the old
check in the previous patch, too (i.e. the simple check of the
interface number) for catching the probe with errors.
Fixes: 39efc9c8a9 ("ALSA: usb-audio: Fix last interface check for registration")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.suse.com/show_bug.cgi?id=1205111
Link: https://lore.kernel.org/r/20221108065824.14418-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SAT SCSI/ATA Translation specification requires SCSI SYNCHRONIZE CACHE
(10) and (16) commands both shall be translated to ATA flush command.
Also, ZBC Zoned Block Commands specification mandates SYNCHRONIZE CACHE
(16) command support. However, libata translates only SYNCHRONIZE CACHE
(10). This results in SYNCHRONIZE CACHE (16) command failures on SATA
drives and then libata translation does not conform to ZBC. To avoid the
failure, add support for SYNCHRONIZE CACHE (16).
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
atc_complete_all() had concurrency bugs, thus remove it:
1/ atc_complete_all() in its entirety was buggy, as when the atchan->queue
list (the one that contains descriptors that are not yet issued to the
hardware) contained descriptors, it fired just the first from the
atchan->queue, but moved all the desc from atchan->queue to
atchan->active_list and considered them all as fired. This could result in
calling the completion of a descriptor that was not yet issued to the
hardware.
2/ when in tasklet at atc_advance_work() time, atchan->active_list was
queried without holding the lock of the chan. This can result in
atchan->active_list concurrency problems between the tasklet and
issue_pending().
Fixes: dc78baa2b9 ("dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller")
Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/13c6c9a2-6db5-c3bf-349b-4c127ad3496a@axentia.se/
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20221025090306.297886-1-tudor.ambarus@microchip.com
Link: https://lore.kernel.org/r/20221025090306.297886-8-tudor.ambarus@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
tx_submit is supposed to push the current transaction descriptor to a
pending queue, waiting for issue_pending() to be called. issue_pending()
must start the transfer, not tx_submit(), thus remove atc_dostart() from
atc_tx_submit(). Clients of at_xdmac that assume that tx_submit() starts
the transfer must be updated and call dma_async_issue_pending() if they
miss to call it.
The vdbg print was moved to after the lock is released. It is desirable to
do the prints without the lock held if possible, and because the if
statement disappears there's no reason why to do the print while holding
the lock.
Fixes: dc78baa2b9 ("dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller")
Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/13c6c9a2-6db5-c3bf-349b-4c127ad3496a@axentia.se/
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20221025090306.297886-1-tudor.ambarus@microchip.com
Link: https://lore.kernel.org/r/20221025090306.297886-3-tudor.ambarus@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When disabling dma channel, a TCF flag is set and as TCIE is enabled, an
interrupt is raised.
On a busy system, the interrupt may have latency and the user can ask for
dmaengine_resume while stm32-dma driver has not yet managed the complete
pause (backup of registers to restore state in resume).
To avoid such a case, instead of waiting the interrupt to backup the
registers, do it just after disabling the channel and discard Transfer
Complete interrupt in case the channel is paused.
Fixes: 099a9a94be ("dmaengine: stm32-dma: add device_pause/device_resume support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20221024083611.132588-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If device_register() fails, it should call put_device() to give
up reference, the name allocated in dev_set_name() can be freed
in callback function kobject_cleanup().
Fixes: 5b65781d06 ("dmaengine: ti: k3-udma-glue: Add support for K3 PKTDMA")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20221020062827.2914148-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The of_xlate callback is supposed to return the channel after already
having 'grabbed' it for private use, so fill that in.
Fixes: b127315d9a ("dmaengine: apple-admac: Add Apple ADMAC driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221019132324.8585-1-povik+lin@cutebit.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When IDXD is not configurable, that means its WQ, engine, and group
configurations cannot be changed. But it can be disabled and its state
should be set as disabled regardless it's configurable or not.
Fix this by setting device state IDXD_DEV_DISABLED for read-only device
as well in idxd_device_clear_state().
Fixes: cf4ac3fef3 ("dmaengine: idxd: fix lockdep warning on device driver removal")
Signed-off-by: Fengqian Gao <fengqian.gao@intel.com>
Reviewed-by: Xiaochen Shen <xiaochen.shen@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220930032835.2290-1-fengqian.gao@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
>From Intel IAA spec [1], Intel IAA does not support batch processing.
Two batch related default values for IAA are incorrect in current code:
(1) The max batch size of device is set during device initialization,
that indicates batch is supported. It should be always 0 on IAA.
(2) The max batch size of work queue is set to WQ_DEFAULT_MAX_BATCH (32)
as the default value regardless of Intel DSA or IAA device during
work queue setup and cleanup. It should be always 0 on IAA.
Fix the issues by setting the max batch size of device and max batch
size of work queue to 0 on IAA device, that means batch is not
supported.
[1]: https://cdrdv2.intel.com/v1/dl/getContent/721858
Fixes: 23084545db ("dmaengine: idxd: set max_xfer and max_batch for RO device")
Fixes: 92452a72eb ("dmaengine: idxd: set defaults for wq configs")
Fixes: bfe1d56091 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220930201528.18621-2-xiaochen.shen@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The first IRQ is required, but IRQs 1 through (nb_phy_chans - 1) are
optional, because on some platforms (e.g. PXA168) there is a single IRQ
shared between all channels.
This change inhibits a flood of "IRQ index # not found" messages at
startup. Tested on a PXA168-based device.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20220906000709.52705-1-doug@schmorgal.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Xin Long says:
====================
sctp: fix a NULL pointer dereference in sctp_sched_dequeue_common
This issue was triggered with SCTP_PR_SCTP_PRIO in sctp,
and caused by not checking and fixing stream->out_curr
after removing a chunk from this stream.
Patch 1 removes an unnecessary check and makes the real
fix easier to add in Patch 2.
====================
Link: https://lore.kernel.org/r/cover.1667598261.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A crash was reported by Zhen Chen:
list_del corruption, ffffa035ddf01c18->next is NULL
WARNING: CPU: 1 PID: 250682 at lib/list_debug.c:49 __list_del_entry_valid+0x59/0xe0
RIP: 0010:__list_del_entry_valid+0x59/0xe0
Call Trace:
sctp_sched_dequeue_common+0x17/0x70 [sctp]
sctp_sched_fcfs_dequeue+0x37/0x50 [sctp]
sctp_outq_flush_data+0x85/0x360 [sctp]
sctp_outq_uncork+0x77/0xa0 [sctp]
sctp_cmd_interpreter.constprop.0+0x164/0x1450 [sctp]
sctp_side_effects+0x37/0xe0 [sctp]
sctp_do_sm+0xd0/0x230 [sctp]
sctp_primitive_SEND+0x2f/0x40 [sctp]
sctp_sendmsg_to_asoc+0x3fa/0x5c0 [sctp]
sctp_sendmsg+0x3d5/0x440 [sctp]
sock_sendmsg+0x5b/0x70
and in sctp_sched_fcfs_dequeue() it dequeued a chunk from stream
out_curr outq while this outq was empty.
Normally stream->out_curr must be set to NULL once all frag chunks of
current msg are dequeued, as we can see in sctp_sched_dequeue_done().
However, in sctp_prsctp_prune_unsent() as it is not a proper dequeue,
sctp_sched_dequeue_done() is not called to do this.
This patch is to fix it by simply setting out_curr to NULL when the
last frag chunk of current msg is dequeued from out_curr stream in
sctp_prsctp_prune_unsent().
Fixes: 5bbbbe32a4 ("sctp: introduce stream scheduler foundations")
Reported-by: Zhen Chen <chenzhen126@huawei.com>
Tested-by: Caowangbao <caowangbao@huawei.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 5bbbbe32a4 ("sctp: introduce stream scheduler foundations"),
sctp_stream_outq_migrate() has been called in sctp_stream_init/update to
removes those chunks to streams higher than the new max. There is no longer
need to do such check in sctp_prsctp_prune_unsent().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a follow-up for commit 974cb0e3e7 ("tipc: fix uninit-value
in tipc_nl_compat_name_table_dump") where it should have type casted
sizeof(..) to int to work when TLV_GET_DATA_LEN() returns a negative
value.
syzbot reported a call trace because of it:
BUG: KMSAN: uninit-value in ...
tipc_nl_compat_name_table_dump+0x841/0xea0 net/tipc/netlink_compat.c:934
__tipc_nl_compat_dumpit+0xab2/0x1320 net/tipc/netlink_compat.c:238
tipc_nl_compat_dumpit+0x991/0xb50 net/tipc/netlink_compat.c:321
tipc_nl_compat_recv+0xb6e/0x1640 net/tipc/netlink_compat.c:1324
genl_family_rcv_msg_doit net/netlink/genetlink.c:731 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:775 [inline]
genl_rcv_msg+0x103f/0x1260 net/netlink/genetlink.c:792
netlink_rcv_skb+0x3a5/0x6c0 net/netlink/af_netlink.c:2501
genl_rcv+0x3c/0x50 net/netlink/genetlink.c:803
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0xf3b/0x1270 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x1288/0x1440 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
Reported-by: syzbot+e5dbaaa238680ce206ea@syzkaller.appspotmail.com
Fixes: 974cb0e3e7 ("tipc: fix uninit-value in tipc_nl_compat_name_table_dump")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/ccd6a7ea801b15aec092c3b532a883b4c5708695.1667594933.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
From ZBC-1:
- RC BASIS = 0: The RETURNED LOGICAL BLOCK ADDRESS field indicates the
highest LBA of a contiguous range of zones that are not sequential write
required zones starting with the first zone.
- RC BASIS = 1: The RETURNED LOGICAL BLOCK ADDRESS field indicates the LBA
of the last logical block on the logical unit.
The current scsi_debug READ CAPACITY response does not comply with the
above if there are one or more sequential write required zones. SCSI
initiators need a way to retrieve the largest valid LBA from SCSI
devices. Reporting the largest valid LBA if there are one or more
sequential zones requires to set the RC BASIS field in the READ CAPACITY
response to one. Hence this patch.
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20221102193248.3177608-1-bvanassche@acm.org
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While BCMGENET select BROADCOM_PHY as y, but PTP_1588_CLOCK_OPTIONAL is m,
kconfig warning and build errors:
WARNING: unmet direct dependencies detected for BROADCOM_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- BCMGENET [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_BROADCOM [=y] && HAS_IOMEM [=y] && ARCH_BCM2835 [=y]
drivers/net/phy/broadcom.o: In function `bcm54xx_suspend':
broadcom.c:(.text+0x6ac): undefined reference to `bcm_ptp_stop'
drivers/net/phy/broadcom.o: In function `bcm54xx_phy_probe':
broadcom.c:(.text+0x784): undefined reference to `bcm_ptp_probe'
drivers/net/phy/broadcom.o: In function `bcm54xx_config_init':
broadcom.c:(.text+0xd4c): undefined reference to `bcm_ptp_config_init'
Fixes: 99addbe31f ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20221105090245.8508-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If CONFIG_MACSEC=m and CONFIG_OCTEONTX2_PF=y, it leads a build error:
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_pfaf_mbox_up_handler':
otx2_pf.c:(.text+0x181c): undefined reference to `cn10k_handle_mcs_event'
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_probe':
otx2_pf.c:(.text+0x437e): undefined reference to `cn10k_mcs_init'
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_remove':
otx2_pf.c:(.text+0x5031): undefined reference to `cn10k_mcs_free'
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_mbox_up_handler_mcs_intr_notify':
otx2_pf.c:(.text+0x5f11): undefined reference to `cn10k_handle_mcs_event'
Make CONFIG_OCTEONTX2_PF depends on CONFIG_MACSEC to fix it. Because
it has empty stub functions of cn10k, CONFIG_OCTEONTX2_PF can be enabled
if CONFIG_MACSEC is disabled
Fixes: c54ffc7360 ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221105063442.2013981-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While working on the nvmem description I figured out this file had the
"nvmem-cell-names" property name misspelled. Fix the typo, as
"nvmem-cells-names" has never existed.
Fixes: 603094b2cd ("dt-bindings: net: Add tsnep Ethernet controller")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221104162147.1288230-1-miquel.raynal@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If transport_add_device() fails in sas_phy_add(), the kernel will crash
trying to delete the device in transport_remove_device() called from
sas_remove_host().
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000108
CPU: 61 PID: 42829 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc1+ #173
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x54/0x3d0
lr : device_del+0x37c/0x3d0
Call trace:
device_del+0x54/0x3d0
attribute_container_class_device_del+0x28/0x38
transport_remove_classdev+0x6c/0x80
attribute_container_device_trigger+0x108/0x110
transport_remove_device+0x28/0x38
sas_phy_delete+0x30/0x60 [scsi_transport_sas]
do_sas_phy_delete+0x6c/0x80 [scsi_transport_sas]
device_for_each_child+0x68/0xb0
sas_remove_children+0x40/0x50 [scsi_transport_sas]
sas_remove_host+0x20/0x38 [scsi_transport_sas]
hisi_sas_remove+0x40/0x68 [hisi_sas_main]
hisi_sas_v2_remove+0x20/0x30 [hisi_sas_v2_hw]
platform_remove+0x2c/0x60
Fix this by checking and handling return value of transport_add_device()
in sas_phy_add().
Fixes: c7ebbbce36 ("[SCSI] SAS transport class")
Suggested-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221107124828.115557-1-yangyingliang@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two problems with meson8b_devm_clk_prepare_enable(),
introduced in commit a54dc4a490 ("net: stmmac: dwmac-meson8b:
Make the clock enabling code re-usable"):
- It doesn't pass the clk argument, but instead always the
rgmii_tx_clk of the device.
- It silently ignores the return value of devm_add_action_or_reset().
The former didn't become an actual bug until another user showed up in
the next commit 9308c47640 ("net: stmmac: dwmac-meson8b: add support
for the RX delay configuration"). The latter means the callers could
end up with the clock not actually prepared/enabled.
Fixes: a54dc4a490 ("net: stmmac: dwmac-meson8b: Make the clock enabling code re-usable")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221104083004.2212520-1-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When iterating the VMAs, the maple state needs to be invalidated if the
tree is modified by a split or merge to ensure the maple tree node
contained in the maple state is still valid. These invalidations were
missed, so add them to the paths which alter the tree.
Reported-by: syzbot+0d2014e4da2ccced5b41@syzkaller.appspotmail.com
Fixes: 69dbe6daf1 (userfaultfd: use maple tree iterator to iterate VMAs)
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix an issue reported when performing a live migration when multipath is
configured with a short fast fail timeout of 5 seconds and also to have
no_path_retry set to fail. In this scenario, all paths would go into the
devloss state while the ibmvfc driver went through discovery to log back
in. On a loaded system, the discovery might take longer than 5 seconds,
which was resulting in all paths being marked failed, which then resulted
in a read only filesystem.
This patch changes the migration code in ibmvfc to avoid deleting rports at
all in this scenario, so we avoid losing all paths.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20221026181356.148517-1-brking@linux.vnet.ibm.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Highlights:
- ACPI: video: Fix regressions from 6.1 backlight refactor by making
acpi_video_backlight_use_native() always return true for now
- Misc. other bugfixes and HW id additions
The following is an automated git shortlog grouped by driver:
ACPI:
- video: Add backlight=native DMI quirk for Dell G15 5515
- video: Make acpi_video_backlight_use_native() always return true
- video: Improve Chromebook checks
hp_wmi:
- Fix rfkill causing soft blocked wifi
ideapad-laptop:
- Disable touchpad_switch
p2sb:
- Don't fail if unknown CPU is found
platform/x86/intel/hid:
- Add some ACPI device IDs
platform/x86/intel/pmt:
- Sapphire Rapids PMT errata fix
touchscreen_dmi:
- Add info for the RCA Cambio W101 v2 2-in-1
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmNo7hsUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9y08wf/Q+GL05jx3uVprDmoQljc3DJnHCut
haa/ZHsqq6OY2RYeY4mX1iYOzlRD20nDEQ52/2IOXvx2FOEorDewByGHD7gOJ6Xr
IvI0JTmfPZ4yflW/N+z2ujXYpp/XlELzHEXFBA6t+62NOT0y4fu2mJx95twDgsa0
ohgTVtmSqIwhjJVt+pQ2UVdy2M+Yv07XabZswLTPt6JZJRhvu8UzPu+DkQd0qqKi
tvmFMkYVSkJnEKBT07Ii+QiUxXDKDzfwRPBFxSEm7m3GvkkPJp0ZqmrB9m8mK6oJ
f83FZ8X9vcTGaG5Gjm3X5xejs4B2qeBs9AzhsrAW/maKOADsbjJdJPz7JQ==
=aes0
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"The most important fixes here are a set of fixes for the ACPI
backlight detection refactor which landed in 6.1.
These fix regressions reported on some laptop models by making
acpi_video_backlight_use_native() always return true for now, which in
essence undoes some of the changes.
I plan to take another shot at having only 1 /sys/class/backlight
class device per panel with 6.2, with modified detection heuristics to
avoid the (known) regressions.
Highlights:
- ACPI: video: Fix regressions from 6.1 backlight refactor by making
acpi_video_backlight_use_native() always return true for now
- Misc other bugfixes and HW id additions"
* tag 'platform-drivers-x86-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: p2sb: Don't fail if unknown CPU is found
platform/x86/intel/hid: Add some ACPI device IDs
platform/x86/intel/pmt: Sapphire Rapids PMT errata fix
platform/x86: hp_wmi: Fix rfkill causing soft blocked wifi
platform/x86: touchscreen_dmi: Add info for the RCA Cambio W101 v2 2-in-1
platform/x86: ideapad-laptop: Disable touchpad_switch
ACPI: video: Add backlight=native DMI quirk for Dell G15 5515
ACPI: video: Make acpi_video_backlight_use_native() always return true
ACPI: video: Improve Chromebook checks
Akira reports:
> "make htmldocs" reports duplicate C declaration of ksize() as follows:
> /linux/Documentation/core-api/mm-api:43: ./mm/slab_common.c:1428: WARNING: Duplicate C declaration, also defined at core-api/mm-api:212.
> Declaration is '.. c:function:: size_t ksize (const void *objp)'.
> This is due to the kernel-doc comment for ksize() declaration added in
> include/linux/slab.h by commit 05a940656e ("slab: Introduce
> kmalloc_size_roundup()").
There is an older kernel-doc comment for ksize() definition in
mm/slab_common.c, which is not only duplicated, but also contradicts the
new one - the additional storage discovered by ksize() should not be
used by callers anymore. Delete the old kernel-doc.
Reported-by: Akira Yokosawa <akiyks@gmail.com>
Link: https://lore.kernel.org/all/d33440f6-40cf-9747-3340-e54ffaf7afb8@gmail.com/
Fixes: 05a940656e ("slab: Introduce kmalloc_size_roundup()")
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Commit 72655fb942 ("drm/panfrost: replace endian-specific types with
native ones") accidentally reverted part of the parent commit
7228d9d792 ("drm/panfrost: Remove type name from internal structs")
leading to the situation that the Panfrost UAPI header still doesn't
compile correctly in C++.
Revert the accidental revert and pass me a brown paper bag.
Reported-by: Alyssa Rosenzweig <alyssa@collabora.com>
Fixes: 72655fb942 ("drm/panfrost: replace endian-specific types with native ones")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Alyssa Rosenzweig <alyssa@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103114036.1581854-1-steven.price@arm.com
If we're doing device replace on a zoned filesystem and discover in
scrub_enumerate_chunks() that we don't have to copy the block group it is
unlocked before it gets skipped.
But as the block group hasn't yet been locked before it leads to a locking
imbalance. To fix this simply remove the unlock.
This was uncovered by fstests' testcase btrfs/163.
Fixes: 9283b9e09a ("btrfs: remove lock protection for BLOCK_GROUP_FLAG_TO_COPY")
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When performing seeding on a zoned filesystem it is necessary to
initialize each zoned device's btrfs_zoned_device_info structure,
otherwise mounting the filesystem will cause a NULL pointer dereference.
This was uncovered by fstests' testcase btrfs/163.
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When cloning a btrfs_device, we're not cloning the associated
btrfs_zoned_device_info structure of the device in case of a zoned
filesystem.
Later on this leads to a NULL pointer dereference when accessing the
device's zone_info for instance when setting a zone as active.
This was uncovered by fstests' testcase btrfs/161.
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This reverts commit 786672e9e1.
[BUG]
Since commit 786672e9e1 ("btrfs: scrub: use larger block size for data
extent scrub"), btrfs scrub no longer reports errors if the corruption
is not in the first sector of a STRIPE_LEN.
The following script can expose the problem:
mkfs.btrfs -f $dev
mount $dev $mnt
xfs_io -f -c "pwrite -S 0xff 0 8k" $mnt/foobar
umount $mnt
# 13631488 is the logical bytenr of above 8K extent
btrfs-map-logical -l 13631488 -b 4096 $dev
mirror 1 logical 13631488 physical 13631488 device /dev/test/scratch1
# Corrupt the 2nd sector of that extent
xfs_io -f -c "pwrite -S 0x00 13635584 4k" $dev
mount $dev $mnt
btrfs scrub start -B $mnt
scrub done for 54e63f9f-0c30-4c84-a33b-5c56014629b7
Scrub started: Mon Nov 7 07:18:27 2022
Status: finished
Duration: 0:00:00
Total to scrub: 536.00MiB
Rate: 0.00B/s
Error summary: no errors found <<<
[CAUSE]
That offending commit enlarges the data extent scrub size from sector
size to BTRFS_STRIPE_LEN, to avoid extra scrub_block to be allocated.
But unfortunately the data extent scrub is still heavily relying on the
fact that there is only one scrub_sector per scrub_block.
Thus it will only check the first sector, and ignoring the remaining
sectors.
Furthermore the error reporting is not able to handle multiple sectors
either.
[FIX]
For now just revert the offending commit.
The consequence is just extra memory usage during scrub.
We will need a proper change to make the remaining data scrub path to
handle multiple sectors before we enlarging the data scrub size.
Reported-by: Li Zhang <zhanglikernel@gmail.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add ENOMEM among the error codes that don't print stack trace on
transaction abort. We've got several reports from syzbot that detects
stacks as errors but caused by limiting memory. As this is an artificial
condition we don't need to know where exactly the error happens, the
abort and error cleanup will continue like e.g. for EIO.
As the transaction aborts code needs to be inline in a lot of code, the
implementation cases about minimal bloat. The error codes are in a
separate function and the WARN uses the condition directly. This
increases the code size by 571 bytes on release build.
Alternatives considered: add -ENOMEM among the errors, this increases
size by 2340 bytes, various attempts to combine the WARN and helper
calls, increase by 700 or more bytes.
Example syzbot reports (error -12):
- https://syzkaller.appspot.com/bug?extid=5244d35be7f589cf093e
- https://syzkaller.appspot.com/bug?extid=9c37714c07194d816417
Signed-off-by: David Sterba <dsterba@suse.com>
The btrfs_alloc_dummy_root() uses ERR_PTR as the error return value
rather than NULL, if error happened, there will be a NULL pointer
dereference:
BUG: KASAN: null-ptr-deref in btrfs_free_dummy_root+0x21/0x50 [btrfs]
Read of size 8 at addr 000000000000002c by task insmod/258926
CPU: 2 PID: 258926 Comm: insmod Tainted: G W 6.1.0-rc2+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
kasan_report+0xb7/0x140
kasan_check_range+0x145/0x1a0
btrfs_free_dummy_root+0x21/0x50 [btrfs]
btrfs_test_free_space_cache+0x1a8c/0x1add [btrfs]
btrfs_run_sanity_tests+0x65/0x80 [btrfs]
init_btrfs_fs+0xec/0x154 [btrfs]
do_one_initcall+0x87/0x2a0
do_init_module+0xdf/0x320
load_module+0x3006/0x3390
__do_sys_finit_module+0x113/0x1b0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: aaedb55bc0 ("Btrfs: add tests for btrfs_get_extent")
CC: stable@vger.kernel.org # 4.9+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
syzkaller found a failed assertion:
assertion failed: (args->devid != (u64)-1) || args->missing, in fs/btrfs/volumes.c:6921
This can be triggered when we set devid to (u64)-1 by ioctl. In this
case, the match of devid will be skipped and the match of device may
succeed incorrectly.
Patch 562d7b1512 introduced this function which is used to match device.
This function contains two matching scenarios, we can distinguish them by
checking the value of args->missing rather than check whether args->devid
and args->uuid is default value.
Reported-by: syzbot+031687116258450f9853@syzkaller.appspotmail.com
Fixes: 562d7b1512 ("btrfs: handle device lookup with btrfs_dev_lookup_args")
CC: stable@vger.kernel.org # 5.16+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The conversion looks harmless, however the addr value is updated inside
the loop with the previous vm_end, which then incorrectly leads to
for_each_vma_range() iterating over stuff outside the range we care
about. Fix this by storing the end value separately. Also fix the case
where the range doesn't intersect with any vma, or if the vma itself
doesn't extend the entire range, which must mean we have hole at the
end. Both should result in an error, as per the previous behaviour.
v2: Fix the cases where the range is empty, or if there's a hole at
the end of the range
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7247
Testcase: igt@gem_userptr_blits@probe
Fixes: f683b9d613 ("i915: use the VMA iterator")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Liam R. Howlett <Liam.Howlett@Oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yu Zhao <yuzhao@google.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221028130635.465839-1-matthew.auld@intel.com
(cherry picked from commit 6f7de35b50860c345babf8ed0aa0d75f9315eee4)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Currently on DG1, which does not have LLC, we hit the below
warning while rebinding an userptr invalidated object.
WARNING: CPU: 4 PID: 13008 at drivers/gpu/drm/i915/gem/i915_gem_pages.c:34 __i915_gem_object_set_pages+0x296/0x2d0 [i915]
...
RIP: 0010:__i915_gem_object_set_pages+0x296/0x2d0 [i915]
...
Call Trace:
<TASK>
i915_gem_userptr_get_pages+0x175/0x1a0 [i915]
____i915_gem_object_get_pages+0x32/0xb0 [i915]
i915_gem_object_userptr_submit_init+0x286/0x470 [i915]
eb_lookup_vmas+0x2ff/0xcf0 [i915]
? __intel_wakeref_get_first+0x55/0xb0 [i915]
i915_gem_do_execbuffer+0x785/0x21d0 [i915]
i915_gem_execbuffer2_ioctl+0xe7/0x3d0 [i915]
We shouldn't be setting the obj->cache_dirty for DGFX,
fix it.
Fixes: d70af57944 ("drm/i915/shmem: ensure flush during swap-in on non-LLC")
Suggested-by: Matthew Auld <matthew.auld@intel.com>
Reported-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Acked-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102051416.27327-1-niranjana.vishwanathapura@intel.com
(cherry picked from commit 0aeec60c76ca2631696b4228f3fc99fe3a80013d)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Currently we are observing mouse cursor stuttering when using
xrandr --scaling=1.2x1.2. X scaling/transformation seems to be
doing fronbuffer rendering. When moving mouse cursor X seems to
perform several invalidates and only one DirtyFB. I.e. it seems
to be assuming updates are sent to panel while drawing is done.
Earlier we were disabling PSR in frontbuffer invalidate call back
(when drawing in X started). PSR was re-enabled in frontbuffer
flush callback (dirtyfb ioctl). This was working fine with X
scaling/transformation. Now we are just enabling continuous full
frame (cff) in PSR invalidate callback. Enabling cff doesn't
trigger any updates. It just configures PSR to send full frame
when updates are sent. I.e. there are no updates on screen before
PSR flush callback is made. X seems to be doing several updates
in frontbuffer before doing dirtyfb ioctl.
Fix this by sending single update on every invalidate callback.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: 805f04d42a ("drm/i915/display/psr: Use continuos full frame to handle frontbuffer invalidations")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6679
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reported-by: Brian J. Tarricone <brian@tarricone.org>
Tested-by: Brian J. Tarricone <brian@tarricone.org>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221024054649.31299-1-jouni.hogander@intel.com
(cherry picked from commit d755f89220a2b49bc90b7b520bb6edeb4adb5f01)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We need to iterate over the original entries here for the sg_table,
pulling out the struct page for each one, to be remapped. However
currently this incorrectly iterates over the final dma mapped entries,
which is likely just one gigantic sg entry if the iommu is enabled,
leading to us only mapping the first struct page (and any physically
contiguous pages following it), even if there is potentially lots more
data to follow.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7306
Fixes: 1286ff7397 ("i915: add dmabuf/prime buffer sharing support.")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Michael J. Ruhl <michael.j.ruhl@intel.com>
Cc: <stable@vger.kernel.org> # v3.5+
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221028155029.494736-1-matthew.auld@intel.com
(cherry picked from commit 28d52f99bbca7227008cf580c9194c9b3516968e)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
